Empire B-Vent Counterflow Wall Furnace (FAW55) Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

Page 1
WARNING
If not installed, operated and maintained
in accordance with the manufacturer's
instructions, this product could expose you
to substances in fuel or from fuel combustion
which can cause death or serious illness.
WARNING
FIRE OR EXPLOSION HAZARD
If the information in these instructions is

may result causing property damage,
personal injury or loss of life.
Do not store or use gasoline or other


WHAT TO DO IF YOU SMELL GAS
 
 
not use any phone in your building.
 
 
from a neighbors phone. Follow the
gas suppliers instructions.
 

 


INSTALLER:

CONSUMER:
Retain this manual for future reference.
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
FAN TYPE VENTED
WALL FURNACE
MODELS:
FAW55IPXLP-1 FAW55IPXNAT-1
37405-4-0519Page 2
TABLE OF CONTENTS
Introduction..................................................................................................................................3-4
Safety Information For Users Of Propane Gas .............................................................................. 5
Installation .................................................................................................................................6-10
Lighting Instructions ..................................................................................................................... 11
Service And Maintenance Suggestions ...................................................................................12-13
Troubleshooting ............................................................................................................................ 14
S8600H Troubleshooting Guide ..............................................................................................15-16
Venting ......................................................................................................................................... 17
Parts List ...................................................................................................................................... 18
Parts View .................................................................................................................................... 19
Master Parts Distributors .............................................................................................................. 20
How To Order Repair Parts .......................................................................................................... 20
Appliance Service History .......................................................................................................21-22
Warranty ....................................................................................................................................... 23
SECTION PAGE
37405-4-0519 Page 3
Introduction
Always consult your local Building Department regarding regulations,
codes or ordinances which apply to the installation of a vented
wall furnace.
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
2. Installermusthaveownerlloutandmailwarrantycardsupplied
with furnace.
3. Installer should show owner how to start and operate furnace.
WARNING
Any change to this furnace or its control can be dangerous.
This is a heating appliance and any panel, door or guard

to operating the appliance.
General Information
ThisseriesisdesigncertiedinaccordancewithAmericanNational
Standard / CSA Standard Z21.86 and CSA 2.32 by the Canadian
Standards Association, as a Fan Type Vented Wall Furnace and
must be installed according to these instructions.
Any alteration of the original design, installed other than as
shown in these instructions or use with a type of gas not
shown on the rating plate is the responsibility of the person
and company making the change.
Important
AllcorrespondenceshouldrefertocompleteModelNo.,SerialNo.
and type of gas.
NOTICE: Duringinitialringofthisunit,itspaintwillbakeoutand
smokewilloccur.Topreventtriggeringofsmokealarms,ventilate
the room in which the unit is installed.
Installation on Rugs and Tile
If this appliance is installed directly on carpeting, tile or other
combustiblematerialotherthanwoodooringtheapplianceshall
be installed on a metal or wood panel extending the full width and
depth of the appliance.
Thebasereferredtoabovedoesnotmeanthere-proofbaseas
used on wood stoves. The protection is for rugs that are extremely
thickandlightcoloredtile.
Installation in Residential Garages
Gas utilization equipment in residential garages shall be installed
so that all burners and burner ignition devices are located not less
than18”(457mm)abovetheoor.
Such equipment shall be located, or protected, so it is not subject
to physical damage by a moving vehicle.

Model FAW-55IP
BTU/HR (KW/H) 55,000 (16.1)
Height 82 3/8” (2092mm)
Width 16” (406mm)
Depth 11 1/2” (292mm)
Gas Inlet 1/2” (13mm) Pipe
Vent Collar 4” (102mm) Type B Oval
CFM 400
INTRODUCTION
ACCESSORIES
Part No. Description
SOR-1 Register,sideoutlet,xedregister
SOK-1 Sideoutlet,10”(254mm)maximumextension,xed
register
ROK-1 Rear Outlet, 10” (254mm) maximum extension,
adjustable register
DV-651 Vent enclosure, 14” (356mm) [for room up to 96
1/2” (245cm) in height]
DV-665 Vent enclosure, 24” (610mm) [for rooms up to 106
1/2” (270.5cm) in height]
DV-666 Vent enclosure, 36” (914mm) [for rooms up to 118
1/2” (301cm) in height]
DV-648 4”(102mm)Oval-to-Roundueadapterkit
CONVERSION KITS
Part Number Description Used On
682160 PropanetoNatural FAW55IPXLP-1
682269 NaturaltoPropane FAW55IPXNAT-1
37405-4-0519Page 4
INTRODUCTION (CONT’D)
 

 

burns or clothing ignition.
 
are in the same room as the appliance.
 
on or near the appliance.
        
an appliance must be replaced prior to operating the
appliance.
 
 Installation and repair should be done by a QUALIFIED
SERVICE PERSON. The appliance should be inspected




circulating air passageways of the appliance be kept
clean.
 put anything around the furnace that will obstruct

  keep the appliance area clear and free from combustible

       
damaged parts.
   
Clean and replace damaged parts.
 
during operation.
 use this heater if any part has been under water.

the heater and to replace any part of the control system
and any gas control which has been under water.
 

THIS IS A HEATING APPLIANCE
DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANELS INSTALLED.
When an existing Category 1 heater is removed or replaced,
the original venting system may no longer be sized to
properly vent the attached appliances. Instructions shall
also indicate effects of an improperly sized venting system
(formationofcondensate,leakage,spillage,etc.)andshall
specify the following test procedure:
WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to follow the steps outlined below for each
      
placed into operation could result in carbon monoxide
poisoning or death.
The following steps shall be followed for each
      
placed into operation, while all other appliances

1. 
2.        

Gas Code, ANSI Z223.1/NFPA 54 or the Natural
Gas and Propane Installation Code, CSA B149.1
and these instructions. Determine that there is no
blockage or restriction, leakage, corrosion and
      
condition.
3. As far as practical, close all building doors and
windows and all doors between the space in which

are located and other spaces of the building.
4. 
5. Turn on clothes dryers and any appliance not
       
exhaust fans, such as range hoods and bathroom
exhausts, so they are operating at maximum
speed. Do operate a summer exhaust fan.
6. Follow the lighting instructions. Place the appliance
being inspected into operation. Adjust the
thermostat so appliance is operating continuously.
7.       
appliances at the draft hood relief opening after 5

of a match or candle.
8. 

in accordance with National Fuel Gas Code, ANSI
Z223.1/NFPA 54 and/or Natural Gas and Propane
Installation Code, CSA B149.1.
9. After is has been determined that each appliance
connected
     
      
     
      

37405-4-0519 Page 5
SAFETY INFORMATION FOR USERS OF PROPANE GAS
-
sions. In its natural state, propane is odorless and colorless.
You may not know all the following safety precautions which
can protect both you and your family from an accident. Read

members of your household. Someday when there may not

exactly what to do. If, after reading the following information,
you feel you still need more information, please contact your
gas supplier.
PROPANE GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas
because of the odorant put in the Propane Gas. That’s your
signal to go into immediate action!
• Donotoperateelectricswitches,lightmatches,useyourphone.
Do not do anything that could ignite the gas.
• Geteveryoneoutofthebuilding,vehicle,trailer,orarea.Do
that IMMEDIATELY.
• Closeallgastankorcylindersupplyvalves.
• PropaneGasisheavierthanairandmaysettleinlowareas
such as basements. When you have reason to suspect a gas
leak,keepoutofbasementsandotherlowareas.Stayout
untilreghtersdeclarethemtobesafe.
• Useyour neighbor's phoneand call a trainedPropane Gas
servicepersonandtheredepartment.Eventhoughyoumay
not continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
• Finally, lettheservicemanandreghterscheckforescaped
gas. Have them air out the area before you return. Properly
trainedPropane Gasservice people shouldrepair the leak,
thencheckandrelightthegasapplianceforyou.
NO ODOR DETECTED - ODOR FADE
Some people cannot smell well. Some people cannot smell the
odorofthechemicalputintothegas.Youmustndoutifyoucan
smelltheodorantinpropane.Smokingcandecreaseyourabilityto
smell. Being around an odor for a time can affect your sensitivity or
abilitytodetectthatodor.Sometimesotherodorsintheareamask
the gas odor. People may not smell the gas odor or their minds are
onsomethingelse.Thinkingaboutsmellingagasodorcanmake
it easier to smell.
The odorant in Propane Gas is colorless, and it can fade under some
circumstances.Forexample,ifthereisanundergroundleak,the
movementofthegasthroughsoilcanltertheodorant.Odorants
in Propane Gas also are subject to oxidation. This fading can occur
ifthereisrustinsidethestoragetankorinirongaspipes.
The odorant in escaped gas can adsorb or absorb onto or into
walls, masonry and other materials and fabrics in a room. That will
takesomeoftheodorantoutofthegas,reducingitsodorintensity.
Propane Gas may stratify in a closed area, and the odor intensity
could vary at different levels. Since it is heavier than air, there may
be more odor at lower levels. Always be sensitive to the slightest gas
odor.Ifyoudetectanyodor,treatitasaseriousleak.Immediately
go into action as instructed earlier.
SOME POINTS TO REMEMBER
• LearntorecognizetheodorofPropaneGas.YourlocalPropane
Gas Dealer can give you a "Scratch and Sniff" pamphlet. Use
ittondoutwhatthepropaneodorsmellslike.Ifyoususpect
thatyourPropaneGashasaweakorabnormalodor,callyour
Propane Gas Dealer.
• Ifyouarenotqualied,donotlightpilotlights,performservice,
ormakeadjustmentstoappliancesonthePropaneGassystem.
Ifyouarequalied,consciouslythinkabouttheodorofPropane
Gas prior to and while lighting pilot lights or performing service
ormakingadjustments.
• Sometimes a basement or a closed-up house has a musty
smell that can cover up the Propane Gas odor. Do not try to
lightpilotlights,performservice,ormakeadjustmentsinan
area where the conditions are such that you may not detect
theodoriftherehasbeenaleakofPropaneGas.
• Odorfade,duetooxidationbyrustoradsorptiononwallsof
newcylindersandtanks,ispossible.Therefore,peopleshould
beparticularlyalertandcarefulwhennewtanksorcylinders
areplacedinservice.Odorfadecanoccurinnewtanks,or
reinstalledoldtanks,iftheyarelledandallowedtosettoo
longbeforerelling.Cylindersandtankswhichhavebeenout
of service for a time may develop internal rust which will cause
odor fade. If such conditions are suspected to exist, a periodic
sniff test of the gas is advisable. If you have any question about
the gas odor, call your Propane Gas Dealer. A periodic sniff
test of the Propane Gas is a good safety measure under any
condition.
• If,atanytime,youdonotsmellthePropaneGasodorantand
youthinkyoushould,assumeyouhavealeak.Thentakethe
same immediate action recommended above for the occasion
when you do detect the odorized Propane Gas.
• Ifyouexperienceacomplete"gasout,"(thecontainerisunder
novaporpressure),turnthetankvalveoffimmediately.Ifthe
container valve is left on, the container may draw in some air
throughopeningssuchaspilotlightorices.Ifthisoccurs,some
new internal rusting could occur. If the valve is left open, then
treatthecontainerasanewtank.Alwaysbesureyourcon-
tainer is under vapor pressure by turning it off at the container
beforeitgoescompletelyemptyorhavingitrelledbeforeitis
completely empty.
37405-4-0519Page 6
Ventilation and Combustion Air
Wall furnaces shall be installed in a location in which the facilities
for ventilation permit satisfactory combustion of gas and proper
venting under normal conditions. In buildings of conventional frame,
brick,orstoneconstructionwithouttightstormwindowsanddoors,
inltrationisnormallyadequatetoprovideairforcombustionand
draft hood dilution.
Whereappliancesareinstalledinconnedandunconnedspaces
within a building, the building being of unusually tight construction,
air for combustion and ventilation must be obtained directly from
outdoors or from such spaces that freely communicate with the
outdoors.Undertheseconditions,theconnedandunconned
spaces shall be provided with two permanent openings, one near
the top of the enclosure and one near the bottom; each opening
shall have a free area of not less than one square inch (6,45cm
2
)
per 2,000 BTU hr. (.6KW/H) of total input.

Installation and replacement of gas piping, gas utilization equipment
or accessories and repair and servicing of equipment shall be
performedonlybyaqualiedagency.Theterm“qualiedagency”
meansanyindividual,rm,corporationorcompanywhicheitherin
person or through a representative is engaged in and is responsible for
(a) the installation or replacement of gas piping or (b) the connection,
installation, repair or servicing of equipment, who is experienced in
suchwork,familiarwithallprecautionsrequiredandhascomplied
with all the requirements of the authority having jurisdiction.
The installation must conform with local codes or, in the absence of
local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA
54,* Natural Gas and Propane Installation Code, CSA B149.1.
*Available from the American National Standards Institute, Inc., 11
West 42nd St., New York, N.Y. 10036.
Clearances
1. In selecting a location for installation, it is necessary to provide
adequate accessibility clearances for servicing and proper
installation.
2. The FAW-55 can be attached to the wall or recessed into the
wall up to 4 inches (102mm) in depth.
3. The wall in which the furnace is recessed has (0) zero (0mm)
clearance to the furnace sides and top.
4. When using side discharge registers, SOR-1 or SOK-1, the
furnace cannot be recessed into the wall.
5. Clearance to sidewall or combustible material is 4 inches
(102mm).
6. Ceiling clearance is 7 1/2 inches (191mm).
7. Floor and rear wall clearance is (0) zero inches (0mm).
8. Clearance of 18 inches (457mm) is required to adjacent wall or
combustiblematerialwhenushmountedSOR-1,sideoutlet
register is used.
Before Installing Consider The Following Venting
1. A chimney for residential-type or low-heat gas utilization
equipment shall extend at least 3 feet (914mm) above the
highest point where it passes through a roof of a building and
at least 2 feet (610mm) higher than any portion of building
within a horizontal distance of 10 feet (3m).
2. Thisfurnacemustnotbeconnectedtoachimneyueserving
a separate solid-fuel burning appliance.
3. Uninsulated Single-Wall Metal Pipe shall not be used
       

4. Attention! This Fan Type Vented Wall Furnace is equipped with
aventsafetyswitch.Intheeventofspillageofueproducts
INSTALLATION
due to improper venting the vent safety switch will open, which
resultsinthemainburnersto“shutoff”.
Refer to Figure 1 and page 16 for additional information regarding
U.L. Listed gas vent equipment.
Installing Optional Side Outlets
Side outlet register, SOR-1 may be installed on one or both sides
of the furnace at the required clearances of 18 inches (457mm) to
adjacent wall or combustible material as shown in Figure 2.
1. Locate and cut the 5 1/2” (140mm) square opening in the cabinet
sideusingthetemplatefromthekit,exposingtheinnerliner
knock-out.
2. Removetheknock-out.
3. Place the register on the 5 1/2” (140mm) opening with the
louverssetforthedesireddirectionandmarkthemounting
holes using the register as a template.
4. Drill (2) 1/8” (3mm) diameter holes in cabinet side and fasten
the register in place with (2) #10 x 1” (25mm) screws provided.
Sideoutletkit,10”(254mm)bootassemblywithregister,SOK-1
for warm air discharge into an adjoining room may be installed on
either side of the furnace at the required clearance of 4 inches to
adjacent wall as shown in Figure 3A.
1. Locate and cut the 5 1/2” (140mm) square opening in the cabinet
sideusingthetemplatefromthekit,exposingtheinnerliner
knock-out.
2. Removetheknock-out.
3. Usingtheinnerandouterbootsasholetemplates,markand
drill (8) 1/8” (3mm) diameter holes in the inner liner and cabinet
side.
4. Using Figure 3A locate and cut a 6 3/4” (171mm) square opening
through walls.
5. Attach furnace to wall. (See Attaching Furnace to Wall).
6. Withfurnaceinplace,aftercheckingalignmentofsideoutlet
opening in wall and furnace, place the 9 3/8” x 9 3/8” (238mm
x 238mm) side outlet wall plate over outer boot, pass the outer
boot through the wall and attach side outlet wall plate to furnace
side of wall with (2) #10 x 1” (25mm) screws provided.
7. Fasten outer boot to the cabinet side with (4) #8 x 1/4” (6mm)
screws provided.
8. Position and attach inner boot to inner liner with (4) #8 x 1/4”
(6mm) screws provided.
9. Locate the register with its louvers positioned for the desired
airdischargedirectionandmarkthemountingholesusingthe
register as a template.
10. Drill (2) 1/8” (3mm) diameter holes in the wall and fasten the
register in place with (2) #10 x 1” (25mm) screws provided
37405-4-0519 Page 7
REGISTER KIT #DV-637
REAR OUTLET
3” (76mm) TO CENTER OF
1/2” (13mm) INLET ELBOW
6-5/8” (168mm)
WALL TO VALVE INLET
3-3/4” (95mm) FLOOR TO
CONTROL VALVE INLET
FURNACE
CLEARANCE TO
COMBUSTIBLES
4” (102mm) MINIMUM
KIT PART DV-608
SIDE OUTLET
TOPTO COMBUSTIBLES
7-1/2” (191mm)
MINIMUM CLEARANCE
4” (102mm) OVAL TYPE “B”
CONNECTION
VENT CENTER TO
COMBUSTIBLES MINIMUM
CLEARANCE 1-9/16” (40mm)
VENTENCLOSURE
DV-651 OR DV-665
OR DV-666
MINIMUM CLEARANCE
TO COMBUSTIBLES
18” (457mm)
REGISTER PART DV-603
Figure 2
(140mm)
(406mm)
(102mm)
(102mm)
(140mm)
(102mm)
3 1/4” (83mm)
11 ½”(292mm)
Figure 3 Figure 3A
Installing Optional Rear Outlet
Rearoutletkit,10”(254mm)bootassemblywithregister,ROK-1
for warm air discharge into an adjoining room.
Attention: Before furnace is attached to the wall, the wall opening
for the rear outlet must be cut, in addition to removal of the outer
andinnercasingknockoutsonfurnace.
1. The wall opening measurements for the rear outlet are the
following.
A. Fromoortobottomofwallopeningis143/4”(375mm).
B. From bottom of wall opening to top of wall opening is 8 1/2”
(216mm) .
C. Wall opening width is 12 1/8” (308mm).
2. Removeoutercasingknockoutfromoutercasingback.
3. Removeinnercasingknockoutfrominnercasing.
4. Attach furnace to wall (see Attaching Furnace to Wall).
5. Align clearance holes on 8” x 12” (203mm x 305mm) boot with
screwholesonoutercasingbackandmarkboottobeush
with wall surface. Remove boot and cut to proper length.
6. Attach8”x12”(203mmx305mm)boottooutercasingback
with (6) #10 x 1/2” (13mm) screws provided.
7. Align clearance holes on 6” x 10” (152mm x 254mm) duct with
screwholesoninnercasingandmarkducttobe21/4”(57mm)
shorter than 8” x 12” (203mm x 305mm) boot. Remove duct
and cut to proper length.
8. Attach 6” x 10” (152mm x 254mm) duct to inner casing with
(6) #10 x 1/2” (13mm) screws provided.
9. Insert rear register into 8” x 12” (203mm x 305mm) boot. Attach
rear register to wall with (2) #10 x 1” (25mm) screws provided.
ALL CONNECTIONS MUST BE MECHANICALLY
MADE AND LISTED CLERANCES MAINTAINED
*PARTS LISTED ARE TO BE
PURCHASED
LOCALLY
SPACER STRAP*
BASE PLATE*
MOUNTING HOLE
2
PIECE VENT ENCLOSURE
CUT
TO THE PROPER LENGTH
BASE PLATE
GASKET
Figure 1
INSTALLATION (CONT’D)
VENTCENTERTOCOMBUSTIBLES
MINIMUMCLEARANCE1-9/16”(40mm)
SIDE OUTLET
KIT PART SOK-1
37405-4-0519Page 8
Locating Furnace On Wall
The furnace is to be located on a wall. The furnace is 16 inches
(406mm) in width and normal 16 inches (406mm) on center studs
will not allow the furnace to be recessed into the wall unless a stud
is repositioned.
A template is provided in furnace carton for locating gas line
connection. Also, refer to Figure 2 for positioning the furnace on
wall and for locating gas line connection.
Locating Gas Supply
Thegaslinecanenterthefurnaceeitherthroughtheoororwall.
The gas line opening should be made at this time. Location of the
openingwillbedeterminedbythepositionofoorjoistsandthe
valve and union used for servicing.
Locating Electric Supply
A7/8”(22mm)diameterknockoutisprovidedatthebottomofthe
left and right side panels. A three-prong (grounding) plug assembly
is located within the control compartment (bottom) of the furnace.
Pleaseremove7/8”(22mm)knockoutfromappropriatesidepanel
when routing plug assembly to an electrical outlet.
Installation of Three-prong (Grounding) Plug Assembly
1. Disconnect nylon cap on 3’ (914mm) plug assembly from nylon
plug on wiring harness. Remove 3’ (914mm) plug assembly from
control compartment (bottom) of the furnace.
2. Remove7/8”(22mm)knockoutfromappropriatesidepanel.
3. Insert nylon cap on 3’ (914mm) plug assembly into the 7/8”
(22mm) hole in the side panel.
4. Connect nylon cap on 3’ (914mm) plug assembly to nylon plug
on the wiring harness.
5. Place 7/8” (22mm) strain relief bushing around the cord of the 3’
(914mm) plug assembly. Insert 7/8” (22mm) strain relief bushing
into the 7/8” (22mm) hole in the side panel.
Attention! The 7/8” (22mm) strain relief bushing is located within
the same yellow envelope as the Installation Instructions and
Owners Manual.
Attaching Furnace to Wall
When attaching furnace to the wall remove that portion of baseboard
and molding on the wall which is behind the furnace. Attach furnace
to wall, at the outer casing top, with (2) toggle bolts provided and
tooor,attheoutercasingbottom,with(2)#10x11/2”(38mm)
screws provided.
Attention! The screw holes on the outer casing bottom are off-set
abovetheoorapproximately3/8”(9.5mm).Donotover-tighten
screws and distort the off-set on the outer casing bottom. Distortion
of the outer casing bottom will not allow the lower front panel to be
attached to the furnace.
Gas Supply
Checkalllocalcodesforrequirements,especiallyforthesizeand
typeofgassupplyline required.OnNaturalGaslineslessthan
15’ (4.5m) long, use 1/2” (13mm) pipe; on longer runs, use 3/4”
(19mm) iron pipe or equal. On Propane Gas lines please consult
Propane Gas supplier.
Installing a New Main Gas Shut-Off
Each appliance should have its own manual gas shut-off.
A manual main gas shut-off should be located in the vicinity of the
unit. Where none exists, or where its size or location is not adequate,
contact your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant
totheactionofliqueedpetroleumgases.Thegaslinesmustbe
checkedforleaksbytheinstaller.Thisshouldbedonewithasoap
solution watching for bubbles on all exposed connections, and if
unexposed, a pressure test should be made.
         



A gas valve and ground joint union should be installed in the gas
line upstream of the gas control to aid in servicing. It is required by
theNationalFuelGasCodethatadriplinebeinstallednearthegas
inlet. This should consist of a vertical length of pipe tee connected
into the gas line that is capped on the bottom in which condensation
and foreign particles may collect.
(3mm)
(3mm)
Figure 4
Method of Installing a Tee Fitting Sediment Trap
The use of the following gas connectors is recommended:
— ANSZ21.24ApplianceConnectorsofCorrugatedMetalTubing
and Fittings
— ANSZ21.45AssembledFlexibleApplianceConnectorsofOther
Than All-Metal Construction
The above connectors may be used if acceptable by the authority
having jurisdiction.
Pressure Testing of the Gas Supply System
1. Tochecktheinletpressuretothegasvalve,a1/8”(3mm)N.P.T.
plugged tapping, accessible for test gauge connection, must
be placed immediately upstream of the gas supply connection
to the appliance.
2. The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2psig(3.5kPa).
3. The appliance must be isolated from the gas supply piping system
by closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal
toorlessthan1/2psig(3.5kPa).
Attention! If one of the above procedures results in pressures in
excessof1/2psig(14”w.c.)(3.5kPa)ontheappliancegasvalve,
it will result in a hazardous condition.
INSTALLATION (CONT’D)
37405-4-0519 Page 9
Figure 6
Electrode and pilot must be kept clean. Clean through pilot
access hole with a small brush (toothbrush) and water.
Proper Main Burner Flame
The correct ame will be a short blue inner ame with a much
largerlightblueouter ame.Themainburner (Figure 7) shows
theapproximateheightofeachpartoftheameforeachgas.The
burnerdoesnothaveaprimaryairadjustment.Theamewillbe
correctifthefactory-setpressureandoriceopeningareused.After
thefurnacehasbeenoperating,theburnerportsmaybeblocked
by foreign matter carried in by combustion air. Therefore, cleaning
oftheburnermaybeneededforproperame.
To clean burner port disconnect the gas supply to the valve, and
remove the eight screws fastening the burner door. After removing the
burner door from the combustion chamber, remove rear burner, pilot
burner and front burner. With front and rear burners removed from
furnace, force water into the ribbon ports and dry with air pressure.
4”
(102mm) NAT
6”
(152mm) LP
1 ½”(38mm) NAT
1/4” (6mm) LP
Figure 7
Replacing Fan and Oiling the Motor
The fan motor should be cleaned and oiled once each heating season.
To reach the motor, withdraw the metal shroud surrounding the fan
blade by removing the screws on each side. Oil holes are located
on the top at each end of the motor. Use a few drops of #10 motor
oil. To clean the motor, blow air through its ventilation openings
with a vacuum cleaner or low pressure air source.
Iffanmotorisreplaced,thesiliconerubbergaskets,seepage14,
IndexNo.5,PartNo.712059shouldalsobereplaced.Thegaskets
mustbestretchedtotthemotorboltsintothegasketholesand
thenthemotorandgasketsinstalledonthemotormountingbars.
Checking Manifold Pressure
Both Propane and Natural Gas valves have a built-in pressure
regulatorinthegasvalve.NaturalGasmodelswillhaveamanifold
pressureofapproximately3.5”w.c.(.871kPa)atthevalveoutlet
with the inlet pressure to the valve from a minimum of 5.0” w.c.
(1.24kPa) for the purpose of input adjustmentto a maximum of
10.5”w.c.(2.615kPa)PropaneGasmodelswillhaveamanifold
pressure approximately 10.0” w.c. (2.49kPa) at the valve outlet
with the inlet pressure to the valve from a minimum of 11.0” w.c.
(2.739kPa)forthepurposeofinputadjustmenttoamaximumof
13.0”w.c.(3.237kPa).
A 1/8” (3mm) N.P.T. plugged tapping, accessible for test gauge
connection, is located on the outlet side of the gas control.
The built-in regulator comes on at approximately 1/4th pressure
and full on in 10 seconds.
Figure 5
High Altitudes
For altitudes/elevations above 2,000 feet (610m), input ratings should
be reduced at the rate of 4 percent for each 1,000 feet (305m) above
sea level. Canadian High Altitudes for locations having an elevation
above mean sea level between 2,000 feet (610m) and 4,500 feet
(1370m), the manifold pressure is to be decreased from 3.5” w.c.
(.871kPa)to2.8”w.c.(.697kPa)forNaturalGasandfrom10.0”w.c.
(2.49kPa)to8.0”w.c.(1.992kPa)forPropaneGas.
Proper Pilot Flame
Thepilotame(Figure 6)goingtothesparkmustbelargeenough
tocompletelycoverthesparkingarea.Withtheproperame,only
2or3sparkswilloccur.Moresparksindicateasmallpilotame
andnoignitionwithsparkstoppingafterapproximately90seconds
generallymeansnotenoughame.
Toadjustpilotameremovethepilotcoverscrewonthecontrol
valve (Figure 5),andturntheadjustmentscrewclockwisetoreduce
ame.Replacepilotcoverscrewtoeliminategasleakage.
Thepilotamewillappearlarge.Abluenearlyhorizontalameis
proper.Thesparkgapmustbe1/8”(3mm).Alargergapcanresult
inthesparkoccurringsomeotherplace.Thepilotameandthe
sparkgaparefactorycheckedandtested.
Afteruse,cleaningmayberequiredfortheproperame.
Safety Lockout
       
lockout. If the pilot fails to light within 90 seconds, the
control system will shut down. The control system must be
reset by turning off the power to the module for one minute.
INSTALLATION (CONT’D)
37405-4-0519Page 10
Vent Safety Shut-Off System
This appliance must be properly connected to a venting system.
This appliance is equipped with a vent safety shutoff system.
Warning: Operation of this wall furnace when not connected
       

carbon monoxide (CO) poisoning and possible death.
This furnace is equipped with a manual reset vent safety switch.
Themanualresetventsafetyswitchwillcausegasowtothemain
burnersto“shutoff”duetoimproperventingorablockedue.
To reset the manual reset vent safety switch:
1. Remove upper front panel.
2. Depress red manual reset button. The manual reset vent
safety switch is located on the draft diverter.
3. Replace upper front panel.
Ifthemanualresetventsafetyswitchcontinuesto“shutoff”the
gasowtothemainburnersaqualiedservicepersonmustbe
contactedtoinspectforimproperventing,blockageintheventpipe
or the manual reset vent safety switch for being defective.
Wiring
The appliance, when installed, must be electrically grounded in
accordance with local codes or, in the absence of local codes, with
the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical
Code, CSA C22.1, if an external electrical source is utilized. This


directly into a properly grounded three-prong receptacle. Do
 For an
ungrounded receptacle, an adapter, which has two prongs and a
wire for grounding, can be purchased, plugged into the ungrounded
receptacle and its wire connected to the receptacle mounting screw.
With this wire completing the ground, the appliance cord plug can
be plugged into the adapter and be electrically grounded. A 7/8”
(22mm) hole is provided in the junction box for use with a conduit
connector if local codes require this type of protection.

Insulated Vent Enclosure
Ventedwallfurnacesinstalledinbuildingswithatroofscanhave
poor venting. The cold vent pipe will have a delay in proper venting
andcausethewallfurnacetoshut“OFF”bytheventsafetyswitch.
Topreventdelayedventingaswellascondensationofueproducts
an insulated vent enclosure is recommended.
Use type B vent pipe and maintain at least a one inch (25mm)
clearance to combustibles.
Use metal thimble to protect vent pipe as it passes through
combustibles.
Installing the

ToinstallanON/OFF
device (such as a
wall switch, remote,
toggle switch, or
thermostat), remove
the wire nut from the
two wires from the
valve. Run additional
wire from the valve
wirestotheON/
OFF device. Install
theON/OFFdevice
in the same room as
the furnace following
the installation
instructions supplied
with it. In the absence
of instructions, install
theON/OFFdevice
4 to 5 feet above the
ooronaninterior
wall not affected
by another heating
source (i.e. stove or
water heater) or the
temperature of an
adjoining room.
INSTALLATION (CONT’D)
Figure 9 Figure 10
IF ANY OF THE ORIGINAL WIRE AS SUPPLIED
WITH THIS UNIT MUST BE REPLACED, IT MUST
BE REPLACED WITH 150°C THERMOPLASTIC
4/64 THICK OR ITS EQUIVALENT.
120V. 60Hz. LESS THAN 3 AMPS
S´IL YAUN FIL ORIGINAL FOURNI AVEC
L´APPAREIL QUI DIOT ÊTRE REMPLACÉ. IL DOIT
ÊTRE REMPLACÉ AVEC UN FIL
THERMOPLASTIQUE 150°C.
120V. 60Hz. MOINS DE 3 AMPS.
—————— ———————————————————————————————————————————————
WHITE (BLANC)
LOW VOLTAGE (BAS VOLTAGE)
120 VOLTS
120 VOLTS
SCHEMATIC WIRING DIAGRAM
——————————————————————————————
SCHÉMA ÉINSTALLATION LECTRIQUE
JUNCTION BOX
—— —— ——— —————————————— ——
BOÎTE DE JONCTION
LIMIT CONTROL
——— ———————————————
CONTROL DE
TOLERANCE
AUTO FAN
——— —— ———————————
VENTILATE
AUTO
TRANSFORMER
——— —— ——————————————————
TRANSFORMATEUR
SPT-3 CORDSET
——— —— ———————————————
CORDON SPT-3
BLACK (NOIR)
LADDER WIRING DIAGRAM
——————————————————————————
DIAGRAMME À L´ÉCHELLE
D´INSTALLATION ÉLECTRIQUE
YELLOW
——— ————————
JAUNE
WHITE
——— ————————
BLANC
BLACK
——— ————————
NOIR
RED
ROUGE
WHT
BLANC
TRANSFORMER
——— —— ——————————————————
TRANSFORMATEUR
24 VOLTS
MOTOR
————— ————
MOTEUR
AUTO FAN
——— —— ———————————
VENTILATEUR
AUTO
MOTOR
————— ————
MOTEUR
VENT SAFETY
——— ———————————————
SÛERTÉ DE
L’ÉVENT
BRN/Brun
WHT/Blanc
RED/Rouge
GRN/Vert
MV
MV/PV
PV
GRND
GAS VALV E
——— ———————————————
VALVE DE GAZ
MODULE
VENT SAFETY
——— ———————————————
SÛERTÉ DE
L’ÉVENT
GAS VALV E
——— ———————————————
VALVE DE GAZ
BRN/Brun
MODULE
WHT/Blanc
RED/Rouge
GRN/Vert
MV
MV/PV
PV
MV
MV/PV
PV
GRND
24V
24V
LIMIT CONTROL
——— ———————————————
CONTROL DE
TOLERANCE
ON/OFF DEVICE
——— ———————————————
ON/OFF
PÉRIPHÉRIQUES
WIRE
NUT
—————————————
FILS
TORSADÉS
WIRE NUT
—————————————----------------
FILS TORSADÉS
ON/OFF DEVICE
——— ———————————————
ON/OFF
PÉRIPHÉRIQUES
(3m)
(.6m)
(3m)
More than 10”
Figure 8
37405-4-0519 Page 11
FOR YOUR SAFETY READ BEFORE OPERATING
 
automatically lights the pilot.
Do not try to light the pilot by hand.
B. BEFORE OPERATING smell all around the appliance area


WHAT TO DO IF YOU SMELL GAS
 
 
Do not use any phone in your building.
 
phone. Follow the gas suppliers instructions.
 
department.
C. Use only your hand to push in or turn the gas control
           


or explosion.
D. Do not use this appliance if any part has been under water.

the appliance and to replace any part of the control system
and any gas control which has been under water.
1. STOP!
2. Turn off all electric power to the appliance.
 
automatically lights the pilot. Do not try to light the pilot
by hand.
 
5. Turn gas control knob clockwise
to “OFF.”
6. Wait ten (10) minutes to clear out any gas. Then smell


smell gas, go to the next step.
7. Turn gas control knob counterclockwise
to “ON”.
8. Replace control access panel (lower front panel).
9. Turn on all electric power to the appliance.
10. If the appliance will not operate, follow the instructions
“TO TURN OFF GAS TO APPLIANCE” and call your ser-

TO TURN OFF GAS TO APPLIANCE
OPERATING INSTRUCTIONS
 
be performed .
 
3. Turn gas control knob clockwise
to “OFF.” Do
not force.
4. Replace control access panel (lower front panel).
LIGHTING INSTRUCTIONS
WARNING

personal injury or loss of life.
37405-4-0519Page 12
CALL SERVICEMAN
SERVICE & MAINTENANCE SUGGESTIONS
GENERAL: Allfurnaceshavebeenre-testedtocheckforproper
operation. This includes, main burner ame, pilot ame, fan
operation, fan control, limit control and automatic valve operation.
If the furnace fails to function on initial installation, it is advisable to
re-checkthefollowing:
1. 115 volts to the junction box.
2. Inlet gas pressure.
3. The 24 volt system.
4. Type of gas being used and that shown on the rating label.
The Service Department at Empire Comfort Systems, Inc. may be
contacted to assist in servicing furnace.

  Disconnect the gas supply at the inlet to the
control valve. Then remove the burner door to which the above
components are attached.
    The upper front panel, the shroud
surrounding the fan blade and fan blade must be removed. See
“OilingtheMotor”paragraphonpage7.
S8600H INTERMITTENT IGNITION MODULE SPECIFICATIONS
Lockouttimingis90seconds.Ignitiontimingisuntilpilotlightsor
lockoutoccurs.
Moduleshutsdownandcutspowertogascontrolonamefailure.
Gascontrolclosestoprovide100percentlockoutonamefailure.
Manual reset required.
ELECTRICALRATINGS:
Voltage and frequency: 20.5 to 28.5V (24V nom.) 60 Hz.
Current rating: 0.2 A.
Valve contact ratings (at 24 Vac):
Run Inrush
Pilot 1.0 A 10.0 A
Main 1.0 A 10.0 A
SPARKGENERATOROUTPUT:13kVpeakat25pfload.
ANTICIPATORSETTING:0.2Apluspilotvalveratingplusmain
valve rating.
COMPATIBILITY: Standard models compatible with all open-close
switch type 24 Vac capable of supplying rated voltage and current
to the module.
AMBIENTTEMPERATURE RATING: Minus 40 F to plus 175 F
(minus 40 C to plus 79 C).
RELATIVEHUMIDITYRATING:5to90percentRHat95F.
FLAMEFAILURERESPONSETIME:0.8secondsat1.0uAame
current.
FLAMECURRENT:1uA,min.
CHECKOUT
Checkoutthegascontrolsystem:
1. At initial installation of the appliance.
2. As part of regular maintenance procedures.
3. Astherststepintroubleshooting.
4. Anytimeworkisdoneonthesystem.
STEP 1: Perform Visual Inspection.
A. Withpoweroff,makesureallwiringconnectionsarecleanand
tight.
B. Turn on power to appliance and ignition module.
C. Open manual shutoff valves in the gas line to the appliance.
D. Dogasleaktestaheadofgascontrolifpipinghasbeendisturbed.
GAS LEAK TEST: Paint pipe joints with rich soap and water
solution.Bubblesindicategasleak.Tightenjointstostopleak.
STEP 2: Review Normal Operating Sequence and Module
Specications.
STEP 3: Reset the Module.
A. Turnthecontrolvalveto“OFF”.
B. Wait one minute.
As you do Steps 4 and 5, watch for points where operation
deviates from normal. Refer to Troubleshooting Chart to correct
problem.
STEP4:CheckSafetyLockoutOperation.
A. Turn gas supply off.
B. Watchforsparkatpilotburner.
C. Time length of spark operation. Maximum spark time is 90
seconds.
D. Openmanualgascockandmakesurenogasisowingtopilot
or main burner.
E. Set thermostat below room temperature and wait one minute
before continuing.
STEP5:CheckNormalOperation.
A. Turn the control valve to call for heat.
B. Make sure pilot lights smoothly when gas reaches the pilot
burner.
C. Makesuremainburnerlightssmoothlywithoutashback.Make
sureburneroperatessmoothlywithoutoatingorlifting.
D. Ifgaslinehasbeendisturbed,completegasleaktest.
GAS LEAK TEST: Paintgascontrolgasketedgesandallpipe
connections downstream of gas control, including pilot tubing
connections, with rich soap and water solution. Bubbles indicate
gasleaks.Tightenjointsandscrewsorreplacecomponentto
stopgasleak.
E. Turnthecontrolvalve off. Make suremain burner andpilot
amesgoout.
OPERATION
Module operation can be conveniently divided into two phases for
S8600H. The phases are trial for ignition and main burner operation.
TRIAL FOR IGNITION
Pilot Ignition
Following call for heat (system start on S8600H), the module
energizestherstmainvalveoperator.Therstmainvalveopens,
whichallowsgastoowtothepilotburner.Atthesametime,the
electronicsparkgeneratorinthemoduleproducesa13,000volt
sparkpulseoutput(at25pfload).Thevoltagegeneratesaspark
at the igniter-sensor that lights the pilot.
37405-4-0519 Page 13
Ifthepilotdoesnotlight,orthepilotamecurrentisnotatleast1.0
uA and steady, the module will not energize the second main valve
and the main burner will not light.
Safety Lockout
S8600H provides 100percent shutoff, or safetylockout.A timer
startstimingthemomentthetrialforignitionstarts.Ignitionspark
continues only until the timed trial for ignition period ends. Then
the module goes into safety lockout. Lockout de-energizes the
rstmainvalveoperatorandclosestherstmainvalveinthegas
control,stoppingpilotgasow.Thecontrolsystemmustbereset
by turning the valve off for one minute or by turning off power to the
module for one minute.
Main Burner Operation
When the pilot ame is established, a ame rectication circuit
iscompletedbetweenthesensorandburnerground.Theame
sensingcircuitinthemoduledetectstheamecurrent,shutsoff
thesparkgeneratorandenergizesthesecondmainvalveoperator.
Thesecondmainvalveopensandgasowstothemainburner,
whereitisignitedbythepilotburner.Theamecurrentalsoholds
thesafetylockouttimerinthereset(normal)operatingcondition.
When the call for heat ends, both main valve operators are de-
energized, and both main valves in the gas control close.
CAUTION: Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous
operation. Verify proper operation after servicing.
SERVICE & MAINTENANCE SUGGESTIONS
Spark Generator Powered
First Valve (Pilot)
Operator Opens
Pilot burner lights.
Module senses flame current.
PILOT BURNER OPERATION
MODULE
S8600H
* Lockout timing is stamped on module.
RESPONSE
After 90 seconds*pilot valve
closes, spark stops.
OR
IF FLAME CURRENT SENSED
Spark generator off
Second valve operator
(Main) opens.
MAIN BURNER OPERATION
Module monitors pilot
flame current.
THERMOSTAT SATISFIED
Valves close. Pilot and
main burners are off.
START
STAGE 1
Trial for Ignition
STAGE 2
Main Burner
Operation
END
S8600H NORMAL OPERATING SEQUENCE
Pilot burner does not light
Thermostat, Wall Switch,
Remote, Etc. Calls for Heat
POWER INTERRUPTION
System shuts off. Restarts when
power is restored.
PILOT FLAME FAILURE
Second main operator closes.
Module starts trial for ignition.
ON/OFFDEVICESATISFIED
Valves close. Pilot and main
burners are off.
Wall Switch, Remote, Etc.
Calls for Heat
37405-4-0519Page 14
Important
1. The following service procedures are provided as a general
guide.
2. Meter readings between gas control and ignition module must
betakenwithinthetrialforignitionperiod.Oncetheignition
modulelocksout,thesystemmustberesetbyturningvalve
off for at least one minute before continuing.
3. Ifanycomponentdoesnotfunctionproperly,makesureitis
correctly installed and wired before replacing it.
4. The ignition module cannot be repaired. If it malfunctions, it
must be replaced.
5. Only trained, experienced service technicians should service
intermittent pilot systems.
Perform the CHECKOUT steps on page 10 as the rst step in
troubleshooting. Then check TROUBLESHOOTING GUIDE to
pinpoint the cause of the problem. If troubleshooting indicates an
ignition problem, see Ignition System Checks below to isolate
and correct the problem.
Following troubleshooting, perform the CHECKOUT procedure
(page 10 ) again to be sure system is operating normally.
Ignition System Checks
Step1:Checkignitioncable.
Makesure:
A. Ignition cable does not touch any metal surfaces.
B. Ignition cable is no more than 36 inches (914mm) long.
C. Connections to the ignition module and to the igniter-sensor
are clean and tight.
D. Ignition cable provides good electrical continuity.
Step2:Checkignitionsystemgrounding.
Nuisance shutdowns are often caused by a poor or erratic
ground.
A. Acommonground,usuallysuppliedbythepilotburnerbracket,
is required for the module and the pilot burner/igniter sensor.
• Check for good metal-to-metal contact between the pilot
burnerbracketandthemainburner.
• CheckthegroundleadfromGND(BURNER)terminalonthe
moduletothepilotburner.Makesureconnectionsareclean
and tight. If the wire is damaged or deteriorated, replace it
with No. 14-18 gauge, moisture-resistant, thermoplastic
insulated wire with 105 C (221 F) minimum rating.
• Ifamerodorbracketarebentoutofposition,restoreto
correct position.
• Replacepilotburner/ignitersensorifinsulatoriscracked.
Step3: Checksparkignitioncircuit.You will need a short jumper
wire made from ignition cable or other heavily insulated
wire.
A. Close the manual gas valve.
B. Disconnect the ignition cable at the SPARK terminal on the
module.
WARNING
When performing the following steps, do not touch stripped
end of jumper or SPARK terminal. The ignition circuit

can result.
C. Energize the module and immediately touch one end of the jumper
rmlytotheGNDterminalonthemodule.Movethefreeend
ofthejumperslowlytowardtheSPARKterminaluntilaspark
is established.
D. Pull the jumper slowly away from the terminal and note the
lengthofthegapwhensparkingstops.Checktablebelow.
ARC LENGTH ACTION
Noarcorarclessthan1/8
inch (3mm).
Arc 1/8 inch (3mm) or longer.
Checkexternalfuse,if
provided.
Verify power at module input
terminal.
Replace module if fuse and
powerokay.
Voltageoutputisokay.
Step4: Checkpilotamecurrent.
A. Turn off furnace.
B. Disconnect main valve wire from the TH or MV terminal on the
gas control.
C. Disconnect ground wire from GND (BURNER) terminal at
module.
D. Connect a meter (dc microamp scale) in series with the ground
lead.
• DisconnectgroundleadfromGNDterminalonignitionmodule.
• Connecttheblack(negative)meterleadtotheignitionmodule
GND(BURNER)terminal.
• Connectthered(positive)meterleadtothefreeendofthe
ground lead.
E. Turnvalveontocallforheat.Thesparkwilllightthepilotbut
the main burner will not light because the main valve actuator
is disconnected.
F. Readthemeter.Theamesensorcurrentmustbesteadyand
at least 1.0 uA.
G. If the reading is less than the minimum or unsteady,
• Make sure pilot ame envelopes 3/8 (9.5mm)to 1/2 inch
(13mm)oftheamerod.
If necessary, adjust pilot flame by turning the pilot
adjustmentscrewonthegascontrolclockwisetodecrease
or counterclockwise to increase pilot ame. Following
adjustment, always replace pilot adjustment cover screw
andtightenrmlytoassurepropergascontroloperation.
• Checkforcrackedceramicinsulator,whichcancauseshort
to ground, and replace igniter-sensor if necessary.
• Makesureelectricalconnectionsarecleanandtight.Replace
damagedwirewithmoisture-resistantNo.18wireratedfor
continuous duty up to 105 C (221 F).
H. Remove meter and reconnect all wires. Return system to
normal operation before leaving job.
TROUBLESHOOTING
37405-4-0519 Page 15
S8600H TROUBLESHOOTING GUIDE
Checklinevoltagepower,lowvoltagetransformer,limitcontroller,andwriting.
Also,checkairprovingswitchoncombustionairblowersystem(ifused)andthattheendswitch(ifused)ismade.
GREEN LED STATUS CODES
Green LED
Flash Code
(X + Y)
a
Indicates Next System Action 
OFF No“CallforHeat” Notapplicable None
Flash Fast Startup-Flame sense calibration Notapplicable None
Heart Beat Normaloperation Notapplicable None
3
Recycle
- Flame failed during run
Initiate new trial for ignition. Flash code
will remain through the ignition trial until
ameisproved.
If system fails to light on next trial for
ignition, check gas supply, pilot burner,
ame sense wiring, contamination of
amerod,burnergroundconnection.
4
Flame sensed out of sequence If situation self corrects within 10 sec-
onds, control returns to normal se-
quence. If ame out of sequence re-
mains longer than 10 seconds, control
goes to Flash code 6 + 4 (see below).
Checkforpilotame.Replacegasvalve
if pilot ame present. If no pilot ame,
cycle“CallforHeat.”Iferrorrepeats,re-
place control.
7
Flamesenseleakagetoground Control remains in wait mode. When the
fault corrects, control resumes normal
operation after a one minute delay.
Check ame sense lead wire for dam-
ageorshorting.Checkthatamerodis
in proper position.
Check ame rod ceramic for cracks,
damageortracking.
8
Low secondary voltage supply -
below 15.5 Vac)
Control remains in wait mode. When the
fault corrects, control resumes normal
operation after a one minute delay.
ChecktransformerandAClineforprop-
er input voltage to the control. Check
with full system load on the transformer.
6 + 2
Failed trial for ignition resulting in
lockout
Remaininlockoutuntil“CallforHeat”is
cycled.
Check gas supply, pilot burner, spark
andamesensewiring,amerodcon-
taminated or out of position, burner
ground connection.
6 + 3
Morethan5amefailuresduring
runonthesame“CallforHeat”re-
sultinginlockout
Remaininlockoutuntil“CallforHeat”is
cycled.
Check gas supply, pilot burner, ame
sense wiring, contamination of ame
rod, burner ground connection.
6 + 4
Flame sensed out of sequence -
longer than 10 seconds
Control waits until ame is no longer
sensed and then goes to soft lockout.
Flash code continues. Control auto re-
setsfromsoftlockoutafteronehour.
Checkforpilotame.Replacegasvalve
if pilot ame present. If no pilot ame,
cycle“CallforHeat.”Iferrorrepeats,re-
place control.
ON
Softlockoutduetoerrordetected
duringselfchecksequences
Controlautoresetsfromsoftlockoutaf-
ter one hour.
Resetbycycling“CallforHeat.”Iferror
repeats, replace the control.
a
Flash Code Descriptions:
- FlashFast:Rapidblinking
- Heartbeat: Constant 1/2 second bright 1/2 second dim cycles
- AsingleashcodenumbersigniesthattheLEDashesXtimesat2Hz,remainsofffortwoseconds,andthenrepeatsthe
sequence.
- X+YashcodessignifythattheLEDashesXtimesat2Hz,remainsofffortwoseconds,ashesYtimesat2Hz,remainsoff
for three seconds, and then repeats the sequence.
37405-4-0519Page 16
S8600H TROUBLESHOOTING GUIDE
37405-4-0519 Page 17
ModelNo.FAW-55maybeventedasshown.Theventcapmust
beatleast12feet(3.7m)abovetheoor.Clearancetocombustible
constructionisheldbythexedspacersat1inch(25mm)withB-1
vent pipe. Installation must conform to local codes.
4” (102mm) Round (all parts purchase locally except item 2)
1. Type B-1 round pipe
2. PartNo.DV-648,4”(102mm)oval-to-roundueadapterkit
(see accessories)
3. Single story type B-1 gas vents require a baseplate and one
pair of ceiling plate spacers.
4. Multi-story type B-1 gas vents require a baseplate, one pair
ofceilingplatespacersattherstoorceilingandonepair
ofrestopspacersateachsuccessiveceilinglevel.
 (all parts purchase locally)
1. Type B-1 oval pipe
2. Single story type B-1 gas vents require a baseplate and one
pair of ceiling plate spacers.
3. Multi-story type B-1 gas vents require a baseplate, one pair
ofceilingplatespacersattherstoorceilingandonepair
ofrestopspacersateachsuccessiveceilinglevel.
(all parts purchase locally)
1. Type B-1 oval pipe
2. Type B-1 oval elbows
3. Single story type B-1 gas vents require a baseplate and one
pair of ceiling plate spacers.
4. Multi-story type B-1 gas vents require a baseplate, one pair
ofceilingplatespacersattherstoorceilingandonepair
ofrestopspacersateachsuccessiveceilinglevel.
Stud space around gas vents must be free of obstructions and
building paper.
Use U.L. listed gas vent equipment when installing the FAW-55. For
vent pipe running through walls, roof, and within one inch (25mm)
of combustible construction, use B-1 (one inch (25mm) clearance
to combustibles) vent pipe. Type B-2 x 4 or Type B-2 x 6 are to be
usedinconjunctionwithaListedrestopspacer.
Type BW gas vent pipe is available for single story or multi-story
installations. Type BW gas vent pipe is to be used with the Listed
baseplate,ceilingplatespacersandrestopspacers.
VENT
ENCLOSURE
(not shown)
ADAPTER
BRACKET
SIDE
FRONT
SIDE
FRONT
SPACER
45 ELBOWS
4" (102MM) OVAL STD.
o
BASEPLATE
FRONT
SIDE
BASEPLATE
VENTING
37405-4-0519Page 18
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
PARTS LIST
Index
No.
Part
No.
Description
1 WFA115 BaseplateGasket
2 11763 Outer Casing Top
3 R618 Motor Mount (Four Required)
4 11764 Motor Mounting Bar (Two Required)
5 M147 Gasket(TwoRequired)
6 R619 Motor
7 11787 Fan Blade
8 DV635 Combustion Chamber
9 11766 Fan Housing
10 11759 Side Panel
11 DV627 Upper Front Panel
12 R1619 Bushing
13 DV823 Diverter Assembly
14 R1749 Vent Safety Switch
15 R1587 Vent Safety Wire Assembly
16 R1536 Bushing
17 11765 Switch Compartment Assembly
18 DV832 Switch Compartment Cover
19 R630 Limit Control
20 R1941 Fan Control
21 DV826 Rear Burner
22 R1617 SparkPlugWire
23 R714L PilotBurnerWithOricePropaneGas
23 R714N PilotBurnerWithOriceNaturalGas
24 DV808 Pilot Tubing
25 DV562 Lower Front Panel
26 DV824 Front Burner
27 P8842
MainBurnerOriceNaturalGas(Two
Required)
27 P8853
MainBurnerOricePropaneGas(Two
Required)
28 DV687 Manifold and Plate Assembly
29 M148 ManifoldGasket
30 DV064 Cover Plate For Observation Hole
31 DV847 BurnerDoorNaturalGas
31 DV972 Burner Door Propane Gas
32 DV691A SealBracket
33 M147 GasketTubingSeal
34 P112 Manifold Union
35 R2147
Gas Valve VR8204C 1126 Propane Gas
(10.0”)
35 R2149
GasValveVR8204C1001NaturalGas
(3.5”)
36 UH810 TransformerMountingBracket
37 R1995 Transformer
38 UH451 Junction Box Cover
39 DV974 Outer Casing Bottom
40 R1515 Bushing
41 R690 Cord Set
42 R896 Bushing
43 DV671 Manifold Support
44 DV765
GasketforChamberAirInlet(Top&Bot-
tom) (Two Required)
45 DV764
GasketforChamberAirInlet(Sides)(Two
Required)
46 R721 Wire Harness
47 R1616 Control Module
48 DV692 ControlModuleMountingBracket
49 R1404 Bushing
50 DV684 Inner Lining Assembly
51 DV629 CasingBack
52 11759 Side Panel
N/S R9832 Wiring Assembly Upper
N/S R9833 Wiring Assembly Lower
N/S R1378 PilotOricePropane
N/S R7429 PilotOriceNatural
Index
No.
Part
No.
Description
37405-4-0519 Page 19
PARTS VIEW
37405-4-0519Page 20
To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.
com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the
nature of the problem with the unit.
To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.
Thislistchangesfromtimetotime.Forthecurrentlist,pleaseclickontheMasterPartsbuttonatwww.empirecomfort.com.
Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original
Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.
MASTER PARTS DISTRIBUTOR LIST
Parts Not Under Warranty
Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distribu-
tors list. For best results, the  should order parts through the distributor. Parts can be shipped directly to the
.
Warranty Parts
Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is  for
warranty parts.
AllpartslistedinthePartsListhaveaPartNumber.Whenorderingparts,rstobtaintheModelNumberandSerialNumberfromthe
nameplateonyourequipment.ThendeterminethePartNumber(nottheIndexNumber)andtheDescriptionofeachpartfromthefol-
lowing illustration and part list. Be sure to give all this information . . .
ApplianceModelNumber Part Description
ApplianceSerialNumber PartNumber
TypeofGas(PropaneorNatural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipmentscontingentuponstrikes,resandallcausesbeyondourcontrol.
HOW TO ORDER REPAIR PARTS
Dey Distributing
1401WillowLakeBoulevard
VadnaisHeights,MN55101
Phone: 651-490-9191
Toll Free: 800-397-1339
Website: www.deydistributing.com
Parts: Heater, Hearth and Grills
F. W. Webb Company
200 Locust Street
Hartford, CT 06114
Phone: 860-722-2433
Toll Free: 800-243-9360
Fax: 860-293-0479
Toll Free Fax: 800-274-2004
Websites: www.fwwebb.com&www.victormfg.com
Parts: Heater, Hearth and Grills
East Coast Energy Products
10 East Route 36
WestLongBranch,NJ07764
Phone: 732-870-8809
Toll Free: 800-755-8809
Fax: 732-870-8811
Website: www.eastcoastenergy.com
Parts: Heater, Hearth and Grills
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Empire B-Vent Counterflow Wall Furnace (FAW55) Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à