Empire B-Vent Counterflow Wall Furnace (FAW55) Le manuel du propriétaire

Marque: Empire

Modèle: B-Vent Counterflow Wall Furnace (FAW55)

Taper: Le manuel du propriétaire

Ce manuel convient également à

FAW55

Page 1

WARNING

If not installed, operated and maintained

in accordance with the manufacturer's

instructions, this product could expose you

to substances in fuel or from fuel combustion

which can cause death or serious illness.

WARNING

FIRE OR EXPLOSION HAZARD

If the information in these instructions is



may result causing property damage,

personal injury or loss of life.

— Do not store or use gasoline or other





— WHAT TO DO IF YOU SMELL GAS

 

 

not use any phone in your building.

 

 

from a neighbor’s phone. Follow the

gas supplier’s instructions.

 



 





INSTALLER:



CONSUMER:

Retain this manual for future reference.

INSTALLATION INSTRUCTIONS

AND OWNER'S MANUAL

FAN TYPE VENTED

WALL FURNACE

MODELS:

FAW55IPXLP-1 FAW55IPXNAT-1

37405-4-0519Page 2

TABLE OF CONTENTS

Introduction..................................................................................................................................3-4

Safety Information For Users Of Propane Gas .............................................................................. 5

Installation .................................................................................................................................6-10

Lighting Instructions ..................................................................................................................... 11

Service And Maintenance Suggestions ...................................................................................12-13

Troubleshooting ............................................................................................................................ 14

S8600H Troubleshooting Guide ..............................................................................................15-16

Venting ......................................................................................................................................... 17

Parts List ...................................................................................................................................... 18

Parts View .................................................................................................................................... 19

Master Parts Distributors .............................................................................................................. 20

How To Order Repair Parts .......................................................................................................... 20

Appliance Service History .......................................................................................................21-22

Warranty ....................................................................................................................................... 23

SECTION PAGE

37405-4-0519 Page 3

Introduction

Always consult your local Building Department regarding regulations,

codes or ordinances which apply to the installation of a vented

wall furnace.

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installermusthaveownerlloutandmailwarrantycardsupplied

with furnace.

3. Installer should show owner how to start and operate furnace.

WARNING

Any change to this furnace or its control can be dangerous.

This is a heating appliance and any panel, door or guard



to operating the appliance.

General Information

ThisseriesisdesigncertiedinaccordancewithAmericanNational

Standard / CSA Standard Z21.86 and CSA 2.32 by the Canadian

Standards Association, as a Fan Type Vented Wall Furnace and

must be installed according to these instructions.

Any alteration of the original design, installed other than as

shown in these instructions or use with a type of gas not

shown on the rating plate is the responsibility of the person

and company making the change.

Important

AllcorrespondenceshouldrefertocompleteModelNo.,SerialNo.

and type of gas.

NOTICE: Duringinitialringofthisunit,itspaintwillbakeoutand

smokewilloccur.Topreventtriggeringofsmokealarms,ventilate

the room in which the unit is installed.

Installation on Rugs and Tile

If this appliance is installed directly on carpeting, tile or other

combustiblematerialotherthanwoodooringtheapplianceshall

be installed on a metal or wood panel extending the full width and

depth of the appliance.

Thebasereferredtoabovedoesnotmeanthere-proofbaseas

used on wood stoves. The protection is for rugs that are extremely

thickandlightcoloredtile.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be installed

so that all burners and burner ignition devices are located not less

than18”(457mm)abovetheoor.

Such equipment shall be located, or protected, so it is not subject

to physical damage by a moving vehicle.



Model FAW-55IP

BTU/HR (KW/H) 55,000 (16.1)

Height 82 3/8” (2092mm)

Width 16” (406mm)

Depth 11 1/2” (292mm)

Gas Inlet 1/2” (13mm) Pipe

Vent Collar 4” (102mm) Type B Oval

CFM 400

INTRODUCTION

ACCESSORIES

Part No. Description

SOR-1 Register,sideoutlet,xedregister

SOK-1 Sideoutlet,10”(254mm)maximumextension,xed

ROK-1 Rear Outlet, 10” (254mm) maximum extension,

adjustable register

DV-651 Vent enclosure, 14” (356mm) [for room up to 96

1/2” (245cm) in height]

DV-665 Vent enclosure, 24” (610mm) [for rooms up to 106

1/2” (270.5cm) in height]

DV-666 Vent enclosure, 36” (914mm) [for rooms up to 118

1/2” (301cm) in height]

DV-648 4”(102mm)Oval-to-Roundueadapterkit

CONVERSION KITS

Part Number Description Used On

682160 PropanetoNatural FAW55IPXLP-1

682269 NaturaltoPropane FAW55IPXNAT-1

37405-4-0519Page 4

INTRODUCTION (CONT’D)

 



 



burns or clothing ignition.

 

are in the same room as the appliance.

 

on or near the appliance.

        

an appliance must be replaced prior to operating the

appliance.

 

 Installation and repair should be done by a QUALIFIED

SERVICE PERSON. The appliance should be inspected









circulating air passageways of the appliance be kept

clean.

 put anything around the furnace that will obstruct



  keep the appliance area clear and free from combustible



       

damaged parts.

   

Clean and replace damaged parts.

 

during operation.

 use this heater if any part has been under water.



the heater and to replace any part of the control system

and any gas control which has been under water.

 



THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANELS INSTALLED.

When an existing Category 1 heater is removed or replaced,

the original venting system may no longer be sized to

properly vent the attached appliances. Instructions shall

also indicate effects of an improperly sized venting system

(formationofcondensate,leakage,spillage,etc.)andshall

specify the following test procedure:

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each

      

placed into operation could result in carbon monoxide

poisoning or death.

The following steps shall be followed for each

      

placed into operation, while all other appliances



1. 

2.        



Gas Code, ANSI Z223.1/NFPA 54 or the Natural

Gas and Propane Installation Code, CSA B149.1

and these instructions. Determine that there is no

blockage or restriction, leakage, corrosion and

      

condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which



are located and other spaces of the building.

4. 

5. Turn on clothes dryers and any appliance not

       

exhaust fans, such as range hoods and bathroom

exhausts, so they are operating at maximum

speed. Do operate a summer exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the

thermostat so appliance is operating continuously.

7.       

appliances at the draft hood relief opening after 5



of a match or candle.

8. 



in accordance with National Fuel Gas Code, ANSI

Z223.1/NFPA 54 and/or Natural Gas and Propane

Installation Code, CSA B149.1.

9. After is has been determined that each appliance

connected

     

      

     

      



37405-4-0519 Page 5

SAFETY INFORMATION FOR USERS OF PROPANE GAS

-

sions. In its natural state, propane is odorless and colorless.

You may not know all the following safety precautions which

can protect both you and your family from an accident. Read



members of your household. Someday when there may not



exactly what to do. If, after reading the following information,

you feel you still need more information, please contact your

gas supplier.

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas

because of the odorant put in the Propane Gas. That’s your

signal to go into immediate action!

• Donotoperateelectricswitches,lightmatches,useyourphone.

Do not do anything that could ignite the gas.

• Geteveryoneoutofthebuilding,vehicle,trailer,orarea.Do

that IMMEDIATELY.

• Closeallgastankorcylindersupplyvalves.

• PropaneGasisheavierthanairandmaysettleinlowareas

such as basements. When you have reason to suspect a gas

leak,keepoutofbasementsandotherlowareas.Stayout

untilreghtersdeclarethemtobesafe.

• Useyour neighbor's phoneand call a trainedPropane Gas

servicepersonandtheredepartment.Eventhoughyoumay

not continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

• Finally, lettheservicemanandreghterscheckforescaped

gas. Have them air out the area before you return. Properly

trainedPropane Gasservice people shouldrepair the leak,

thencheckandrelightthegasapplianceforyou.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell the

odorofthechemicalputintothegas.Youmustndoutifyoucan

smelltheodorantinpropane.Smokingcandecreaseyourabilityto

smell. Being around an odor for a time can affect your sensitivity or

abilitytodetectthatodor.Sometimesotherodorsintheareamask

the gas odor. People may not smell the gas odor or their minds are

onsomethingelse.Thinkingaboutsmellingagasodorcanmake

it easier to smell.

The odorant in Propane Gas is colorless, and it can fade under some

circumstances.Forexample,ifthereisanundergroundleak,the

movementofthegasthroughsoilcanltertheodorant.Odorants

in Propane Gas also are subject to oxidation. This fading can occur

ifthereisrustinsidethestoragetankorinirongaspipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That will

takesomeoftheodorantoutofthegas,reducingitsodorintensity.

Propane Gas may stratify in a closed area, and the odor intensity

could vary at different levels. Since it is heavier than air, there may

be more odor at lower levels. Always be sensitive to the slightest gas

odor.Ifyoudetectanyodor,treatitasaseriousleak.Immediately

go into action as instructed earlier.

SOME POINTS TO REMEMBER

• LearntorecognizetheodorofPropaneGas.YourlocalPropane

Gas Dealer can give you a "Scratch and Sniff" pamphlet. Use

ittondoutwhatthepropaneodorsmellslike.Ifyoususpect

thatyourPropaneGashasaweakorabnormalodor,callyour

Propane Gas Dealer.

• Ifyouarenotqualied,donotlightpilotlights,performservice,

ormakeadjustmentstoappliancesonthePropaneGassystem.

Ifyouarequalied,consciouslythinkabouttheodorofPropane

Gas prior to and while lighting pilot lights or performing service

ormakingadjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the Propane Gas odor. Do not try to

lightpilotlights,performservice,ormakeadjustmentsinan

area where the conditions are such that you may not detect

theodoriftherehasbeenaleakofPropaneGas.

• Odorfade,duetooxidationbyrustoradsorptiononwallsof

newcylindersandtanks,ispossible.Therefore,peopleshould

beparticularlyalertandcarefulwhennewtanksorcylinders

areplacedinservice.Odorfadecanoccurinnewtanks,or

reinstalledoldtanks,iftheyarelledandallowedtosettoo

longbeforerelling.Cylindersandtankswhichhavebeenout

of service for a time may develop internal rust which will cause

odor fade. If such conditions are suspected to exist, a periodic

sniff test of the gas is advisable. If you have any question about

the gas odor, call your Propane Gas Dealer. A periodic sniff

test of the Propane Gas is a good safety measure under any

condition.

• If,atanytime,youdonotsmellthePropaneGasodorantand

youthinkyoushould,assumeyouhavealeak.Thentakethe

same immediate action recommended above for the occasion

when you do detect the odorized Propane Gas.

• Ifyouexperienceacomplete"gasout,"(thecontainerisunder

novaporpressure),turnthetankvalveoffimmediately.Ifthe

container valve is left on, the container may draw in some air

throughopeningssuchaspilotlightorices.Ifthisoccurs,some

new internal rusting could occur. If the valve is left open, then

treatthecontainerasanewtank.Alwaysbesureyourcon-

tainer is under vapor pressure by turning it off at the container

beforeitgoescompletelyemptyorhavingitrelledbeforeitis

completely empty.

37405-4-0519Page 6

Ventilation and Combustion Air

Wall furnaces shall be installed in a location in which the facilities

for ventilation permit satisfactory combustion of gas and proper

venting under normal conditions. In buildings of conventional frame,

brick,orstoneconstructionwithouttightstormwindowsanddoors,

inltrationisnormallyadequatetoprovideairforcombustionand

draft hood dilution.

Whereappliancesareinstalledinconnedandunconnedspaces

within a building, the building being of unusually tight construction,

air for combustion and ventilation must be obtained directly from

outdoors or from such spaces that freely communicate with the

outdoors.Undertheseconditions,theconnedandunconned

spaces shall be provided with two permanent openings, one near

the top of the enclosure and one near the bottom; each opening

shall have a free area of not less than one square inch (6,45cm

)

per 2,000 BTU hr. (.6KW/H) of total input.



Installation and replacement of gas piping, gas utilization equipment

or accessories and repair and servicing of equipment shall be

performedonlybyaqualiedagency.Theterm“qualiedagency”

meansanyindividual,rm,corporationorcompanywhicheitherin

person or through a representative is engaged in and is responsible for

(a) the installation or replacement of gas piping or (b) the connection,

installation, repair or servicing of equipment, who is experienced in

suchwork,familiarwithallprecautionsrequiredandhascomplied

with all the requirements of the authority having jurisdiction.

The installation must conform with local codes or, in the absence of

local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA

54,* Natural Gas and Propane Installation Code, CSA B149.1.

*Available from the American National Standards Institute, Inc., 11

West 42nd St., New York, N.Y. 10036.

Clearances

1. In selecting a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper

installation.

2. The FAW-55 can be attached to the wall or recessed into the

wall up to 4 inches (102mm) in depth.

3. The wall in which the furnace is recessed has (0) zero (0mm)

clearance to the furnace sides and top.

4. When using side discharge registers, SOR-1 or SOK-1, the

furnace cannot be recessed into the wall.

5. Clearance to sidewall or combustible material is 4 inches

(102mm).

6. Ceiling clearance is 7 1/2 inches (191mm).

7. Floor and rear wall clearance is (0) zero inches (0mm).

8. Clearance of 18 inches (457mm) is required to adjacent wall or

combustiblematerialwhenushmountedSOR-1,sideoutlet

Before Installing Consider The Following Venting

1. A chimney for residential-type or low-heat gas utilization

equipment shall extend at least 3 feet (914mm) above the

highest point where it passes through a roof of a building and

at least 2 feet (610mm) higher than any portion of building

within a horizontal distance of 10 feet (3m).

2. Thisfurnacemustnotbeconnectedtoachimneyueserving

a separate solid-fuel burning appliance.

3. Uninsulated Single-Wall Metal Pipe shall not be used

       



4. Attention! This Fan Type Vented Wall Furnace is equipped with

aventsafetyswitch.Intheeventofspillageofueproducts

INSTALLATION

due to improper venting the vent safety switch will open, which

resultsinthemainburnersto“shutoff”.

Refer to Figure 1 and page 16 for additional information regarding

U.L. Listed gas vent equipment.

Installing Optional Side Outlets

Side outlet register, SOR-1 may be installed on one or both sides

of the furnace at the required clearances of 18 inches (457mm) to

adjacent wall or combustible material as shown in Figure 2.

1. Locate and cut the 5 1/2” (140mm) square opening in the cabinet

sideusingthetemplatefromthekit,exposingtheinnerliner

knock-out.

2. Removetheknock-out.

3. Place the register on the 5 1/2” (140mm) opening with the

louverssetforthedesireddirectionandmarkthemounting

holes using the register as a template.

4. Drill (2) 1/8” (3mm) diameter holes in cabinet side and fasten

the register in place with (2) #10 x 1” (25mm) screws provided.

Sideoutletkit,10”(254mm)bootassemblywithregister,SOK-1

for warm air discharge into an adjoining room may be installed on

either side of the furnace at the required clearance of 4 inches to

adjacent wall as shown in Figure 3A.

1. Locate and cut the 5 1/2” (140mm) square opening in the cabinet

sideusingthetemplatefromthekit,exposingtheinnerliner

knock-out.

2. Removetheknock-out.

3. Usingtheinnerandouterbootsasholetemplates,markand

drill (8) 1/8” (3mm) diameter holes in the inner liner and cabinet

side.

4. Using Figure 3A locate and cut a 6 3/4” (171mm) square opening

through walls.

5. Attach furnace to wall. (See Attaching Furnace to Wall).

6. Withfurnaceinplace,aftercheckingalignmentofsideoutlet

opening in wall and furnace, place the 9 3/8” x 9 3/8” (238mm

x 238mm) side outlet wall plate over outer boot, pass the outer

boot through the wall and attach side outlet wall plate to furnace

side of wall with (2) #10 x 1” (25mm) screws provided.

7. Fasten outer boot to the cabinet side with (4) #8 x 1/4” (6mm)

screws provided.

8. Position and attach inner boot to inner liner with (4) #8 x 1/4”

(6mm) screws provided.

9. Locate the register with its louvers positioned for the desired

airdischargedirectionandmarkthemountingholesusingthe

10. Drill (2) 1/8” (3mm) diameter holes in the wall and fasten the

37405-4-0519 Page 7

REAR OUTLET

3” (76mm) TO CENTER OF

1/2” (13mm) INLET ELBOW

6-5/8” (168mm)

WALL TO VALVE INLET

3-3/4” (95mm) FLOOR TO

CONTROL VALVE INLET

FURNACE

CLEARANCE TO

COMBUSTIBLES

4” (102mm) MINIMUM

KIT PART DV-608

SIDE OUTLET

TOPTO COMBUSTIBLES

7-1/2” (191mm)

MINIMUM CLEARANCE

4” (102mm) OVAL TYPE “B”

CONNECTION

VENT CENTER TO

COMBUSTIBLES MINIMUM

CLEARANCE 1-9/16” (40mm)

VENTENCLOSURE

DV-651 OR DV-665

OR DV-666

MINIMUM CLEARANCE

TO COMBUSTIBLES

18” (457mm)

Figure 2

(140mm)

(406mm)

(102mm)

(140mm)

(102mm)

3 1/4” (83mm)

11 ½”(292mm)

Figure 3 Figure 3A

Installing Optional Rear Outlet

Rearoutletkit,10”(254mm)bootassemblywithregister,ROK-1

for warm air discharge into an adjoining room.

Attention: Before furnace is attached to the wall, the wall opening

for the rear outlet must be cut, in addition to removal of the outer

andinnercasingknockoutsonfurnace.

1. The wall opening measurements for the rear outlet are the

following.

A. Fromoortobottomofwallopeningis143/4”(375mm).

B. From bottom of wall opening to top of wall opening is 8 1/2”

(216mm) .

C. Wall opening width is 12 1/8” (308mm).

2. Removeoutercasingknockoutfromoutercasingback.

3. Removeinnercasingknockoutfrominnercasing.

4. Attach furnace to wall (see Attaching Furnace to Wall).

5. Align clearance holes on 8” x 12” (203mm x 305mm) boot with

screwholesonoutercasingbackandmarkboottobeush

with wall surface. Remove boot and cut to proper length.

6. Attach8”x12”(203mmx305mm)boottooutercasingback

with (6) #10 x 1/2” (13mm) screws provided.

7. Align clearance holes on 6” x 10” (152mm x 254mm) duct with

screwholesoninnercasingandmarkducttobe21/4”(57mm)

shorter than 8” x 12” (203mm x 305mm) boot. Remove duct

and cut to proper length.

8. Attach 6” x 10” (152mm x 254mm) duct to inner casing with

(6) #10 x 1/2” (13mm) screws provided.

9. Insert rear register into 8” x 12” (203mm x 305mm) boot. Attach

rear register to wall with (2) #10 x 1” (25mm) screws provided.

ALL CONNECTIONS MUST BE MECHANICALLY

MADE AND LISTED CLERANCES MAINTAINED

*PARTS LISTED ARE TO BE

PURCHASED

LOCALLY

SPACER STRAP*

BASE PLATE*

MOUNTING HOLE

PIECE VENT ENCLOSURE

CUT

TO THE PROPER LENGTH

BASE PLATE

GASKET

Figure 1

INSTALLATION (CONT’D)

VENTCENTERTOCOMBUSTIBLES

MINIMUMCLEARANCE1-9/16”(40mm)

SIDE OUTLET

KIT PART SOK-1

37405-4-0519Page 8

Locating Furnace On Wall

The furnace is to be located on a wall. The furnace is 16 inches

(406mm) in width and normal 16 inches (406mm) on center studs

will not allow the furnace to be recessed into the wall unless a stud

is repositioned.

A template is provided in furnace carton for locating gas line

connection. Also, refer to Figure 2 for positioning the furnace on

wall and for locating gas line connection.

Locating Gas Supply

Thegaslinecanenterthefurnaceeitherthroughtheoororwall.

The gas line opening should be made at this time. Location of the

openingwillbedeterminedbythepositionofoorjoistsandthe

valve and union used for servicing.

Locating Electric Supply

A7/8”(22mm)diameterknockoutisprovidedatthebottomofthe

left and right side panels. A three-prong (grounding) plug assembly

is located within the control compartment (bottom) of the furnace.

Pleaseremove7/8”(22mm)knockoutfromappropriatesidepanel

when routing plug assembly to an electrical outlet.

Installation of Three-prong (Grounding) Plug Assembly

1. Disconnect nylon cap on 3’ (914mm) plug assembly from nylon

plug on wiring harness. Remove 3’ (914mm) plug assembly from

control compartment (bottom) of the furnace.

2. Remove7/8”(22mm)knockoutfromappropriatesidepanel.

3. Insert nylon cap on 3’ (914mm) plug assembly into the 7/8”

(22mm) hole in the side panel.

4. Connect nylon cap on 3’ (914mm) plug assembly to nylon plug

on the wiring harness.

5. Place 7/8” (22mm) strain relief bushing around the cord of the 3’

(914mm) plug assembly. Insert 7/8” (22mm) strain relief bushing

into the 7/8” (22mm) hole in the side panel.

Attention! The 7/8” (22mm) strain relief bushing is located within

the same yellow envelope as the Installation Instructions and

Owner’s Manual.

Attaching Furnace to Wall

When attaching furnace to the wall remove that portion of baseboard

and molding on the wall which is behind the furnace. Attach furnace

to wall, at the outer casing top, with (2) toggle bolts provided and

tooor,attheoutercasingbottom,with(2)#10x11/2”(38mm)

screws provided.

Attention! The screw holes on the outer casing bottom are off-set

abovetheoorapproximately3/8”(9.5mm).Donotover-tighten

screws and distort the off-set on the outer casing bottom. Distortion

of the outer casing bottom will not allow the lower front panel to be

attached to the furnace.

Gas Supply

Checkalllocalcodesforrequirements,especiallyforthesizeand

typeofgassupplyline required.OnNaturalGaslineslessthan

15’ (4.5m) long, use 1/2” (13mm) pipe; on longer runs, use 3/4”

(19mm) iron pipe or equal. On Propane Gas lines please consult

Propane Gas supplier.

Installing a New Main Gas Shut-Off

Each appliance should have its own manual gas shut-off.

A manual main gas shut-off should be located in the vicinity of the

unit. Where none exists, or where its size or location is not adequate,

contact your local authorized installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant

totheactionofliqueedpetroleumgases.Thegaslinesmustbe

checkedforleaksbytheinstaller.Thisshouldbedonewithasoap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made.

         







A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required by

theNationalFuelGasCodethatadriplinebeinstallednearthegas

inlet. This should consist of a vertical length of pipe tee connected

into the gas line that is capped on the bottom in which condensation

and foreign particles may collect.

(3mm)

Figure 4

Method of Installing a Tee Fitting Sediment Trap

The use of the following gas connectors is recommended:

— ANSZ21.24ApplianceConnectorsofCorrugatedMetalTubing

and Fittings

— ANSZ21.45AssembledFlexibleApplianceConnectorsofOther

Than All-Metal Construction

The above connectors may be used if acceptable by the authority

having jurisdiction.

Pressure Testing of the Gas Supply System

1. Tochecktheinletpressuretothegasvalve,a1/8”(3mm)N.P.T.

plugged tapping, accessible for test gauge connection, must

be placed immediately upstream of the gas supply connection

to the appliance.

2. The appliance and its individual shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of

1/2psig(3.5kPa).

3. The appliance must be isolated from the gas supply piping system

by closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal

toorlessthan1/2psig(3.5kPa).

Attention! If one of the above procedures results in pressures in

excessof1/2psig(14”w.c.)(3.5kPa)ontheappliancegasvalve,

it will result in a hazardous condition.

INSTALLATION (CONT’D)

37405-4-0519 Page 9

Figure 6

Electrode and pilot must be kept clean. Clean through pilot

access hole with a small brush (toothbrush) and water.

Proper Main Burner Flame

The correct ame will be a short blue inner ame with a much

largerlightblueouter ame.Themainburner (Figure 7) shows

theapproximateheightofeachpartoftheameforeachgas.The

burnerdoesnothaveaprimaryairadjustment.Theamewillbe

correctifthefactory-setpressureandoriceopeningareused.After

thefurnacehasbeenoperating,theburnerportsmaybeblocked

by foreign matter carried in by combustion air. Therefore, cleaning

oftheburnermaybeneededforproperame.

To clean burner port disconnect the gas supply to the valve, and

remove the eight screws fastening the burner door. After removing the

burner door from the combustion chamber, remove rear burner, pilot

burner and front burner. With front and rear burners removed from

furnace, force water into the ribbon ports and dry with air pressure.

4”

(102mm) NAT

6”

(152mm) LP

1 ½”(38mm) NAT

1/4” (6mm) LP

Figure 7

Replacing Fan and Oiling the Motor

The fan motor should be cleaned and oiled once each heating season.

To reach the motor, withdraw the metal shroud surrounding the fan

blade by removing the screws on each side. Oil holes are located

on the top at each end of the motor. Use a few drops of #10 motor

oil. To clean the motor, blow air through its ventilation openings

with a vacuum cleaner or low pressure air source.

Iffanmotorisreplaced,thesiliconerubbergaskets,seepage14,

IndexNo.5,PartNo.712059shouldalsobereplaced.Thegaskets

mustbestretchedtotthemotorboltsintothegasketholesand

thenthemotorandgasketsinstalledonthemotormountingbars.

Checking Manifold Pressure

Both Propane and Natural Gas valves have a built-in pressure

regulatorinthegasvalve.NaturalGasmodelswillhaveamanifold

pressureofapproximately3.5”w.c.(.871kPa)atthevalveoutlet

with the inlet pressure to the valve from a minimum of 5.0” w.c.

(1.24kPa) for the purpose of input adjustmentto a maximum of

10.5”w.c.(2.615kPa)PropaneGasmodelswillhaveamanifold

pressure approximately 10.0” w.c. (2.49kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 11.0” w.c.

(2.739kPa)forthepurposeofinputadjustmenttoamaximumof

13.0”w.c.(3.237kPa).

A 1/8” (3mm) N.P.T. plugged tapping, accessible for test gauge

connection, is located on the outlet side of the gas control.

The built-in regulator comes on at approximately 1/4th pressure

and full on in 10 seconds.

Figure 5

High Altitudes

For altitudes/elevations above 2,000 feet (610m), input ratings should

be reduced at the rate of 4 percent for each 1,000 feet (305m) above

sea level. Canadian High Altitudes for locations having an elevation

above mean sea level between 2,000 feet (610m) and 4,500 feet

(1370m), the manifold pressure is to be decreased from 3.5” w.c.

(.871kPa)to2.8”w.c.(.697kPa)forNaturalGasandfrom10.0”w.c.

(2.49kPa)to8.0”w.c.(1.992kPa)forPropaneGas.

Proper Pilot Flame

Thepilotame(Figure 6)goingtothesparkmustbelargeenough

tocompletelycoverthesparkingarea.Withtheproperame,only

2or3sparkswilloccur.Moresparksindicateasmallpilotame

andnoignitionwithsparkstoppingafterapproximately90seconds

generallymeansnotenoughame.

Toadjustpilotameremovethepilotcoverscrewonthecontrol

valve (Figure 5),andturntheadjustmentscrewclockwisetoreduce

ame.Replacepilotcoverscrewtoeliminategasleakage.

Thepilotamewillappearlarge.Abluenearlyhorizontalameis

proper.Thesparkgapmustbe1/8”(3mm).Alargergapcanresult

inthesparkoccurringsomeotherplace.Thepilotameandthe

sparkgaparefactorycheckedandtested.

Afteruse,cleaningmayberequiredfortheproperame.

Safety Lockout

       

lockout. If the pilot fails to light within 90 seconds, the

control system will shut down. The control system must be

reset by turning off the power to the module for one minute.

INSTALLATION (CONT’D)

37405-4-0519Page 10

Vent Safety Shut-Off System

This appliance must be properly connected to a venting system.

This appliance is equipped with a vent safety shutoff system.

Warning: Operation of this wall furnace when not connected

       



carbon monoxide (CO) poisoning and possible death.

This furnace is equipped with a manual reset vent safety switch.

Themanualresetventsafetyswitchwillcausegasowtothemain

burnersto“shutoff”duetoimproperventingorablockedue.

To reset the manual reset vent safety switch:

1. Remove upper front panel.

2. Depress red manual reset button. The manual reset vent

safety switch is located on the draft diverter.

3. Replace upper front panel.

Ifthemanualresetventsafetyswitchcontinuesto“shutoff”the

gasowtothemainburnersaqualiedservicepersonmustbe

contactedtoinspectforimproperventing,blockageintheventpipe

or the manual reset vent safety switch for being defective.

Wiring

The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical

Code, CSA C22.1, if an external electrical source is utilized. This





directly into a properly grounded three-prong receptacle. Do

 For an

ungrounded receptacle, an adapter, which has two prongs and a

wire for grounding, can be purchased, plugged into the ungrounded

receptacle and its wire connected to the receptacle mounting screw.

With this wire completing the ground, the appliance cord plug can

be plugged into the adapter and be electrically grounded. A 7/8”

(22mm) hole is provided in the junction box for use with a conduit

connector if local codes require this type of protection.



Insulated Vent Enclosure

Ventedwallfurnacesinstalledinbuildingswithatroofscanhave

poor venting. The cold vent pipe will have a delay in proper venting

andcausethewallfurnacetoshut“OFF”bytheventsafetyswitch.

Topreventdelayedventingaswellascondensationofueproducts

an insulated vent enclosure is recommended.

Use type B vent pipe and maintain at least a one inch (25mm)

clearance to combustibles.

Use metal thimble to protect vent pipe as it passes through

combustibles.

Installing the



ToinstallanON/OFF

device (such as a

wall switch, remote,

toggle switch, or

thermostat), remove

the wire nut from the

two wires from the

valve. Run additional

wire from the valve

wirestotheON/

OFF device. Install

theON/OFFdevice

in the same room as

the furnace following

the installation

instructions supplied

with it. In the absence

of instructions, install

theON/OFFdevice

4 to 5 feet above the

ooronaninterior

wall not affected

by another heating

source (i.e. stove or

water heater) or the

temperature of an

adjoining room.

INSTALLATION (CONT’D)

Figure 9 Figure 10

IF ANY OF THE ORIGINAL WIRE AS SUPPLIED

WITH THIS UNIT MUST BE REPLACED, IT MUST

BE REPLACED WITH 150°C THERMOPLASTIC

4/64 THICK OR ITS EQUIVALENT.

120V. 60Hz. LESS THAN 3 AMPS

S´IL YAUN FIL ORIGINAL FOURNI AVEC

L´APPAREIL QUI DIOT ÊTRE REMPLACÉ. IL DOIT

ÊTRE REMPLACÉ AVEC UN FIL

THERMOPLASTIQUE 150°C.

120V. 60Hz. MOINS DE 3 AMPS.

—————— ———————————————————————————————————————————————

WHITE (BLANC)

LOW VOLTAGE (BAS VOLTAGE)

120 VOLTS

SCHEMATIC WIRING DIAGRAM

——————————————————————————————

SCHÉMA ÉINSTALLATION LECTRIQUE

JUNCTION BOX

—— —— ——— —————————————— ——

BOÎTE DE JONCTION

LIMIT CONTROL

——— — ——————————————— —

CONTROL DE

TOLERANCE

AUTO FAN

——— —— ——————————— —

VENTILATE

AUTO

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

SPT-3 CORDSET

——— —— ——————————————— —

CORDON SPT-3

BLACK (NOIR)

LADDER WIRING DIAGRAM

——————————————————————————

DIAGRAMME À L´ÉCHELLE

D´INSTALLATION ÉLECTRIQUE

YELLOW

——— —————————

JAUNE

WHITE

——— —————————

BLANC

BLACK

——— —————————

NOIR

RED

—

ROUGE

WHT

—

BLANC

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

24 VOLTS

MOTOR

————— —————

MOTEUR

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

MOTOR

————— —————

MOTEUR

VENT SAFETY

——— — ——————————————— —

SÛERTÉ DE

L’ÉVENT

BRN/Brun

WHT/Blanc

RED/Rouge

GRN/Vert

MV/PV

GRND

GAS VALV E

——— — ——————————————— —

VALVE DE GAZ

MODULE

VENT SAFETY

——— — ——————————————— —

SÛERTÉ DE

L’ÉVENT

GAS VALV E

——— — ——————————————— —

VALVE DE GAZ

BRN/Brun

MODULE

WHT/Blanc

RED/Rouge

GRN/Vert

MV/PV

GRND

24V

LIMIT CONTROL

——— — ——————————————— —

CONTROL DE

TOLERANCE

ON/OFF DEVICE

——— — ——————————————— —

ON/OFF

PÉRIPHÉRIQUES

WIRE

NUT

————————————— —

FILS

TORSADÉS

WIRE NUT

—————————————---------------- —

FILS TORSADÉS

ON/OFF DEVICE

——— — ——————————————— —

ON/OFF

PÉRIPHÉRIQUES

(3m)

(.6m)

(3m)

More than 10”

Figure 8

37405-4-0519 Page 11

FOR YOUR SAFETY READ BEFORE OPERATING

 

automatically lights the pilot.

Do not try to light the pilot by hand.

B. BEFORE OPERATING smell all around the appliance area





WHAT TO DO IF YOU SMELL GAS

 

 

Do not use any phone in your building.

 

phone. Follow the gas supplier’s instructions.

 

department.

C. Use only your hand to push in or turn the gas control

           





or explosion.

D. Do not use this appliance if any part has been under water.



the appliance and to replace any part of the control system

and any gas control which has been under water.

1. STOP!

2. Turn off all electric power to the appliance.

 

automatically lights the pilot. Do not try to light the pilot

by hand.

 

5. Turn gas control knob clockwise

to “OFF.”

6. Wait ten (10) minutes to clear out any gas. Then smell





smell gas, go to the next step.

7. Turn gas control knob counterclockwise

to “ON”.

8. Replace control access panel (lower front panel).

9. Turn on all electric power to the appliance.

10. If the appliance will not operate, follow the instructions

“TO TURN OFF GAS TO APPLIANCE” and call your ser-



TO TURN OFF GAS TO APPLIANCE

OPERATING INSTRUCTIONS

 

be performed .

 

3. Turn gas control knob clockwise

to “OFF.” Do

not force.

4. Replace control access panel (lower front panel).

LIGHTING INSTRUCTIONS

WARNING



personal injury or loss of life.

37405-4-0519Page 12

CALL SERVICEMAN

SERVICE & MAINTENANCE SUGGESTIONS

GENERAL: Allfurnaceshavebeenre-testedtocheckforproper

operation. This includes, main burner ame, pilot ame, fan

operation, fan control, limit control and automatic valve operation.

If the furnace fails to function on initial installation, it is advisable to

re-checkthefollowing:

1. 115 volts to the junction box.

2. Inlet gas pressure.

3. The 24 volt system.

4. Type of gas being used and that shown on the rating label.

The Service Department at Empire Comfort Systems, Inc. may be

contacted to assist in servicing furnace.



  Disconnect the gas supply at the inlet to the

control valve. Then remove the burner door to which the above

components are attached.

    The upper front panel, the shroud

surrounding the fan blade and fan blade must be removed. See

“OilingtheMotor”paragraphonpage7.

S8600H INTERMITTENT IGNITION MODULE SPECIFICATIONS

Lockouttimingis90seconds.Ignitiontimingisuntilpilotlightsor

lockoutoccurs.

Moduleshutsdownandcutspowertogascontrolonamefailure.

Gascontrolclosestoprovide100percentlockoutonamefailure.

Manual reset required.

ELECTRICALRATINGS:

Voltage and frequency: 20.5 to 28.5V (24V nom.) 60 Hz.

Current rating: 0.2 A.

Valve contact ratings (at 24 Vac):

Run Inrush

Pilot 1.0 A 10.0 A

Main 1.0 A 10.0 A

SPARKGENERATOROUTPUT:13kVpeakat25pfload.

ANTICIPATORSETTING:0.2Apluspilotvalveratingplusmain

valve rating.

COMPATIBILITY: Standard models compatible with all open-close

switch type 24 Vac capable of supplying rated voltage and current

to the module.

AMBIENTTEMPERATURE RATING: Minus 40 F to plus 175 F

(minus 40 C to plus 79 C).

RELATIVEHUMIDITYRATING:5to90percentRHat95F.

FLAMEFAILURERESPONSETIME:0.8secondsat1.0uAame

current.

FLAMECURRENT:1uA,min.

CHECKOUT

Checkoutthegascontrolsystem:

1. At initial installation of the appliance.

2. As part of regular maintenance procedures.

 3. Astherststepintroubleshooting.

 4. Anytimeworkisdoneonthesystem.

STEP 1: Perform Visual Inspection.

 A. Withpoweroff,makesureallwiringconnectionsarecleanand

tight.

B. Turn on power to appliance and ignition module.

C. Open manual shutoff valves in the gas line to the appliance.

 D. Dogasleaktestaheadofgascontrolifpipinghasbeendisturbed.

GAS LEAK TEST: Paint pipe joints with rich soap and water

solution.Bubblesindicategasleak.Tightenjointstostopleak.

STEP 2: Review Normal Operating Sequence and Module

Specications.

STEP 3: Reset the Module.

 A. Turnthecontrolvalveto“OFF”.

B. Wait one minute.

As you do Steps 4 and 5, watch for points where operation

deviates from normal. Refer to Troubleshooting Chart to correct

problem.

STEP4:CheckSafetyLockoutOperation.

A. Turn gas supply off.

 B. Watchforsparkatpilotburner.

 C. Time length of spark operation. Maximum spark time is 90

seconds.

 D. Openmanualgascockandmakesurenogasisowingtopilot

or main burner.

E. Set thermostat below room temperature and wait one minute

before continuing.

STEP5:CheckNormalOperation.

A. Turn the control valve to call for heat.

 B. Make sure pilot lights smoothly when gas reaches the pilot

burner.

 C. Makesuremainburnerlightssmoothlywithoutashback.Make

sureburneroperatessmoothlywithoutoatingorlifting.

 D. Ifgaslinehasbeendisturbed,completegasleaktest.

GAS LEAK TEST: Paintgascontrolgasketedgesandallpipe

connections downstream of gas control, including pilot tubing

connections, with rich soap and water solution. Bubbles indicate

gasleaks.Tightenjointsandscrewsorreplacecomponentto

stopgasleak.

 E. Turnthecontrolvalve off. Make suremain burner andpilot

amesgoout.

OPERATION

Module operation can be conveniently divided into two phases for

S8600H. The phases are trial for ignition and main burner operation.

TRIAL FOR IGNITION

Pilot Ignition

Following call for heat (system start on S8600H), the module

energizestherstmainvalveoperator.Therstmainvalveopens,

whichallowsgastoowtothepilotburner.Atthesametime,the

electronicsparkgeneratorinthemoduleproducesa13,000volt

sparkpulseoutput(at25pfload).Thevoltagegeneratesaspark

at the igniter-sensor that lights the pilot.

37405-4-0519 Page 13

Ifthepilotdoesnotlight,orthepilotamecurrentisnotatleast1.0

uA and steady, the module will not energize the second main valve

and the main burner will not light.

Safety Lockout

S8600H provides 100percent shutoff, or safetylockout.A timer

startstimingthemomentthetrialforignitionstarts.Ignitionspark

continues only until the timed trial for ignition period ends. Then

the module goes into safety lockout. Lockout de-energizes the

rstmainvalveoperatorandclosestherstmainvalveinthegas

control,stoppingpilotgasow.Thecontrolsystemmustbereset

by turning the valve off for one minute or by turning off power to the

module for one minute.

Main Burner Operation

When the pilot ame is established, a ame rectication circuit

iscompletedbetweenthesensorandburnerground.Theame

sensingcircuitinthemoduledetectstheamecurrent,shutsoff

thesparkgeneratorandenergizesthesecondmainvalveoperator.

Thesecondmainvalveopensandgasowstothemainburner,

whereitisignitedbythepilotburner.Theamecurrentalsoholds

thesafetylockouttimerinthereset(normal)operatingcondition.

When the call for heat ends, both main valve operators are de-

energized, and both main valves in the gas control close.

CAUTION: Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

SERVICE & MAINTENANCE SUGGESTIONS

Spark Generator Powered

First Valve (Pilot)

Operator Opens

Pilot burner lights.

Module senses flame current.

PILOT BURNER OPERATION

MODULE

S8600H

* Lockout timing is stamped on module.

RESPONSE

After 90 seconds*pilot valve

closes, spark stops.

IF FLAME CURRENT SENSED

Spark generator off

Second valve operator

(Main) opens.

MAIN BURNER OPERATION

Module monitors pilot

flame current.

THERMOSTAT SATISFIED

Valves close. Pilot and

main burners are off.

START

STAGE 1

Trial for Ignition

STAGE 2

Main Burner

Operation

END

S8600H NORMAL OPERATING SEQUENCE

Pilot burner does not light

Thermostat, Wall Switch,

Remote, Etc. Calls for Heat

POWER INTERRUPTION

System shuts off. Restarts when

power is restored.

PILOT FLAME FAILURE

Second main operator closes.

Module starts trial for ignition.

ON/OFFDEVICESATISFIED

Valves close. Pilot and main

burners are off.

Wall Switch, Remote, Etc.

Calls for Heat

37405-4-0519Page 14

Important

1. The following service procedures are provided as a general

guide.

2. Meter readings between gas control and ignition module must

betakenwithinthetrialforignitionperiod.Oncetheignition

modulelocksout,thesystemmustberesetbyturningvalve

off for at least one minute before continuing.

 3. Ifanycomponentdoesnotfunctionproperly,makesureitis

correctly installed and wired before replacing it.

4. The ignition module cannot be repaired. If it malfunctions, it

must be replaced.

5. Only trained, experienced service technicians should service

intermittent pilot systems.

Perform the CHECKOUT steps on page 10 as the rst step in

troubleshooting.  Then check TROUBLESHOOTING GUIDE to

pinpoint the cause of the problem. If troubleshooting indicates an

ignition problem, see Ignition System Checks below to isolate

and correct the problem.

Following troubleshooting, perform the CHECKOUT procedure

(page 10 ) again to be sure system is operating normally.

Ignition System Checks

Step1:Checkignitioncable.

Makesure:

A. Ignition cable does not touch any metal surfaces.

B. Ignition cable is no more than 36 inches (914mm) long.

C. Connections to the ignition module and to the igniter-sensor

are clean and tight.

D. Ignition cable provides good electrical continuity.

Step2:Checkignitionsystemgrounding.

Nuisance shutdowns are often caused by a poor or erratic

ground.

 A. Acommonground,usuallysuppliedbythepilotburnerbracket,

is required for the module and the pilot burner/igniter sensor.

• Check for good metal-to-metal contact between the pilot

burnerbracketandthemainburner.

• CheckthegroundleadfromGND(BURNER)terminalonthe

moduletothepilotburner.Makesureconnectionsareclean

and tight. If the wire is damaged or deteriorated, replace it

with No.  14-18 gauge, moisture-resistant, thermoplastic

insulated wire with 105 C (221 F) minimum rating.

• Ifamerodorbracketarebentoutofposition,restoreto

correct position.

• Replacepilotburner/ignitersensorifinsulatoriscracked.

Step3: Checksparkignitioncircuit.You will need a short jumper

wire made from ignition cable or other heavily insulated

wire.

A. Close the manual gas valve.

B. Disconnect the ignition cable at the SPARK terminal on the

module.

WARNING

When performing the following steps, do not touch stripped

end of jumper or SPARK terminal. The ignition circuit



can result.

C. Energize the module and immediately touch one end of the jumper

rmlytotheGNDterminalonthemodule.Movethefreeend

ofthejumperslowlytowardtheSPARKterminaluntilaspark

is established.

D. Pull the jumper slowly away from the terminal and note the

lengthofthegapwhensparkingstops.Checktablebelow.

ARC LENGTH ACTION

Noarcorarclessthan1/8

inch (3mm).

Arc 1/8 inch (3mm) or longer.

Checkexternalfuse,if

provided.

Verify power at module input

terminal.

Replace module if fuse and

powerokay.

Voltageoutputisokay.

Step4: Checkpilotamecurrent.

A. Turn off furnace.

B. Disconnect main valve wire from the TH or MV terminal on the

gas control.

 C. Disconnect ground wire from GND (BURNER) terminal at

module.

D. Connect a meter (dc microamp scale) in series with the ground

lead.

• DisconnectgroundleadfromGNDterminalonignitionmodule.

• Connecttheblack(negative)meterleadtotheignitionmodule

GND(BURNER)terminal.

• Connectthered(positive)meterleadtothefreeendofthe

ground lead.

 E. Turnvalveontocallforheat.Thesparkwilllightthepilotbut

the main burner will not light because the main valve actuator

is disconnected.

 F. Readthemeter.Theamesensorcurrentmustbesteadyand

at least 1.0 uA.

G. If the reading is less than the minimum or unsteady,

• Make sure pilot ame envelopes 3/8 (9.5mm)to 1/2 inch

(13mm)oftheamerod.

• If necessary, adjust pilot flame by turning the pilot

adjustmentscrewonthegascontrolclockwisetodecrease

or counterclockwise to increase pilot ame.  Following

adjustment, always replace pilot adjustment cover screw

andtightenrmlytoassurepropergascontroloperation.

• Checkforcrackedceramicinsulator,whichcancauseshort

to ground, and replace igniter-sensor if necessary.

• Makesureelectricalconnectionsarecleanandtight.Replace

damagedwirewithmoisture-resistantNo.18wireratedfor

continuous duty up to 105 C (221 F).

H. Remove meter and reconnect all wires. Return system to

normal operation before leaving job.

TROUBLESHOOTING

37405-4-0519 Page 15

S8600H TROUBLESHOOTING GUIDE

Checklinevoltagepower,lowvoltagetransformer,limitcontroller,andwriting.

Also,checkairprovingswitchoncombustionairblowersystem(ifused)andthattheendswitch(ifused)ismade.

GREEN LED STATUS CODES

Green LED

Flash Code

(X + Y)

Indicates Next System Action 

OFF No“CallforHeat” Notapplicable None

Flash Fast Startup-Flame sense calibration Notapplicable None

Heart Beat Normaloperation Notapplicable None

Recycle

- Flame failed during run

Initiate new trial for ignition. Flash code

will remain through the ignition trial until

ameisproved.

If system fails to light on next trial for

ignition, check gas supply, pilot burner,

ame sense wiring, contamination of

amerod,burnergroundconnection.

Flame sensed out of sequence If situation self corrects within 10 sec-

onds, control returns to normal se-

quence. If ame out of sequence re-

mains longer than 10 seconds, control

goes to Flash code 6 + 4 (see below).

Checkforpilotame.Replacegasvalve

if pilot ame present. If no pilot ame,

cycle“CallforHeat.”Iferrorrepeats,re-

place control.

Flamesenseleakagetoground Control remains in wait mode. When the

fault corrects, control resumes normal

operation after a one minute delay.

Check ame sense lead wire for dam-

ageorshorting.Checkthatamerodis

in proper position.

Check ame rod ceramic for cracks,

damageortracking.

Low secondary voltage supply -

below 15.5 Vac)

Control remains in wait mode. When the

fault corrects, control resumes normal

operation after a one minute delay.

ChecktransformerandAClineforprop-

er input voltage to the control. Check

with full system load on the transformer.

6 + 2

Failed trial for ignition resulting in

lockout

Remaininlockoutuntil“CallforHeat”is

cycled.

Check gas supply, pilot burner, spark

andamesensewiring,amerodcon-

taminated or out of position, burner

ground connection.

6 + 3

Morethan5amefailuresduring

runonthesame“CallforHeat”re-

sultinginlockout

Remaininlockoutuntil“CallforHeat”is

cycled.

Check gas supply, pilot burner, ame

sense wiring, contamination of ame

rod, burner ground connection.

6 + 4

Flame sensed out of sequence -

longer than 10 seconds

Control waits until ame is no longer

sensed and then goes to soft lockout.

Flash code continues. Control auto re-

setsfromsoftlockoutafteronehour.

Checkforpilotame.Replacegasvalve

if pilot ame present. If no pilot ame,

cycle“CallforHeat.”Iferrorrepeats,re-

place control.

Softlockoutduetoerrordetected

duringselfchecksequences

Controlautoresetsfromsoftlockoutaf-

ter one hour.

Resetbycycling“CallforHeat.”Iferror

repeats, replace the control.

Flash Code Descriptions:

 - FlashFast:Rapidblinking

- Heartbeat: Constant 1/2 second bright 1/2 second dim cycles

 - AsingleashcodenumbersigniesthattheLEDashesXtimesat2Hz,remainsofffortwoseconds,andthenrepeatsthe

sequence.

 - X+YashcodessignifythattheLEDashesXtimesat2Hz,remainsofffortwoseconds,ashesYtimesat2Hz,remainsoff

for three seconds, and then repeats the sequence.

37405-4-0519Page 16

S8600H TROUBLESHOOTING GUIDE

37405-4-0519 Page 17

ModelNo.FAW-55maybeventedasshown.Theventcapmust

beatleast12feet(3.7m)abovetheoor.Clearancetocombustible

constructionisheldbythexedspacersat1inch(25mm)withB-1

vent pipe. Installation must conform to local codes.

4” (102mm) Round (all parts purchase locally except item 2)

1. Type B-1 round pipe

 2. PartNo.DV-648,4”(102mm)oval-to-roundueadapterkit

(see accessories)

3. Single story type B-1 gas vents require a baseplate and one

pair of ceiling plate spacers.

4. Multi-story type B-1 gas vents require a baseplate, one pair

ofceilingplatespacersattherstoorceilingandonepair

ofrestopspacersateachsuccessiveceilinglevel.

 (all parts purchase locally)

1. Type B-1 oval pipe

2. Single story type B-1 gas vents require a baseplate and one

pair of ceiling plate spacers.

3. Multi-story type B-1 gas vents require a baseplate, one pair

ofceilingplatespacersattherstoorceilingandonepair

ofrestopspacersateachsuccessiveceilinglevel.

(all parts purchase locally)

1. Type B-1 oval pipe

2. Type B-1 oval elbows

3. Single story type B-1 gas vents require a baseplate and one

pair of ceiling plate spacers.

4. Multi-story type B-1 gas vents require a baseplate, one pair

ofceilingplatespacersattherstoorceilingandonepair

ofrestopspacersateachsuccessiveceilinglevel.

Stud space around gas vents must be free of obstructions and

building paper.

Use U.L. listed gas vent equipment when installing the FAW-55. For

vent pipe running through walls, roof, and within one inch (25mm)

of combustible construction, use B-1 (one inch (25mm) clearance

to combustibles) vent pipe. Type B-2 x 4 or Type B-2 x 6 are to be

usedinconjunctionwithaListedrestopspacer.

Type BW gas vent pipe is available for single story or multi-story

installations. Type BW gas vent pipe is to be used with the Listed

baseplate,ceilingplatespacersandrestopspacers.

VENT

ENCLOSURE

(not shown)

ADAPTER

BRACKET

SIDE

FRONT

SIDE

FRONT

SPACER

45 ELBOWS

4" (102MM) OVAL STD.

BASEPLATE

FRONT

SIDE

BASEPLATE

VENTING

37405-4-0519Page 18

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

PARTS LIST

Index

No.

Part

No.

Description

1 WFA115 BaseplateGasket

2 11763 Outer Casing Top

3 R618 Motor Mount (Four Required)

4 11764 Motor Mounting Bar (Two Required)

5 M147 Gasket(TwoRequired)

6 R619 Motor

7 11787 Fan Blade

8 DV635 Combustion Chamber

9 11766 Fan Housing

10 11759 Side Panel

11 DV627 Upper Front Panel

12 R1619 Bushing

13 DV823 Diverter Assembly

14 R1749 Vent Safety Switch

15 R1587 Vent Safety Wire Assembly

16 R1536 Bushing

17 11765 Switch Compartment Assembly

18 DV832 Switch Compartment Cover

19 R630 Limit Control

20 R1941 Fan Control

21 DV826 Rear Burner

22 R1617 SparkPlugWire

23 R714L PilotBurnerWithOricePropaneGas

23 R714N PilotBurnerWithOriceNaturalGas

24 DV808 Pilot Tubing

25 DV562 Lower Front Panel

26 DV824 Front Burner

27 P8842

MainBurnerOriceNaturalGas(Two

Required)

27 P8853

MainBurnerOricePropaneGas(Two

Required)

28 DV687 Manifold and Plate Assembly

29 M148 ManifoldGasket

30 DV064 Cover Plate For Observation Hole

31 DV847 BurnerDoorNaturalGas

31 DV972 Burner Door Propane Gas

32 DV691A SealBracket

33 M147 GasketTubingSeal

34 P112 Manifold Union

35 R2147

Gas Valve VR8204C 1126 Propane Gas

(10.0”)

35 R2149

GasValveVR8204C1001NaturalGas

(3.5”)

36 UH810 TransformerMountingBracket

37 R1995 Transformer

38 UH451 Junction Box Cover

39 DV974 Outer Casing Bottom

40 R1515 Bushing

41 R690 Cord Set

42 R896 Bushing

43 DV671 Manifold Support

44 DV765

GasketforChamberAirInlet(Top&Bot-

tom) (Two Required)

45 DV764

GasketforChamberAirInlet(Sides)(Two

Required)

46 R721 Wire Harness

47 R1616 Control Module

48 DV692 ControlModuleMountingBracket

49 R1404 Bushing

50 DV684 Inner Lining Assembly

51 DV629 CasingBack

52 11759 Side Panel

N/S R9832 Wiring Assembly Upper

N/S R9833 Wiring Assembly Lower

N/S R1378 PilotOricePropane

N/S R7429 PilotOriceNatural

Index

No.

Part

No.

Description

37405-4-0519 Page 19

PARTS VIEW

37405-4-0519Page 20

To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.

com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the

nature of the problem with the unit.

To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.

Thislistchangesfromtimetotime.Forthecurrentlist,pleaseclickontheMasterPartsbuttonatwww.empirecomfort.com.

Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original

Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.

MASTER PARTS DISTRIBUTOR LIST

Parts Not Under Warranty

Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distribu-

tors list. For best results, the  should order parts through the distributor. Parts can be shipped directly to the

.

Warranty Parts

Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is  for

warranty parts.

AllpartslistedinthePartsListhaveaPartNumber.Whenorderingparts,rstobtaintheModelNumberandSerialNumberfromthe

nameplateonyourequipment.ThendeterminethePartNumber(nottheIndexNumber)andtheDescriptionofeachpartfromthefol-

lowing illustration and part list. Be sure to give all this information . . .

ApplianceModelNumber Part Description

ApplianceSerialNumber  PartNumber

TypeofGas(PropaneorNatural)

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.

Shipmentscontingentuponstrikes,resandallcausesbeyondourcontrol.

HOW TO ORDER REPAIR PARTS

Dey Distributing

1401WillowLakeBoulevard

VadnaisHeights,MN55101

Phone: 651-490-9191

Toll Free: 800-397-1339

Website: www.deydistributing.com

Parts: Heater, Hearth and Grills

F. W. Webb Company

200 Locust Street

Hartford, CT 06114

Phone: 860-722-2433

Toll Free: 800-243-9360

Fax: 860-293-0479

Toll Free Fax: 800-274-2004

Websites: www.fwwebb.com&www.victormfg.com

Parts: Heater, Hearth and Grills

East Coast Energy Products

10 East Route 36

WestLongBranch,NJ07764

Phone: 732-870-8809

Toll Free: 800-755-8809

Fax: 732-870-8811

Website: www.eastcoastenergy.com

Parts: Heater, Hearth and Grills

La page charge ...

Empire B-Vent Counterflow Wall Furnace (FAW55) Le manuel du propriétaire

Marque: Empire

Modèle: B-Vent Counterflow Wall Furnace (FAW55)

Taper: Le manuel du propriétaire

Ce manuel convient également à

FAW55

Télécharger le PDF

rapport

dans d''autres langues

English: Empire B-Vent Counterflow Wall Furnace (FAW55) Owner's manual

Empire B-Vent Counterflow Wall Furnace (FAW55) Le manuel du propriétaire

Ce manuel convient également à

Empire B-Vent Counterflow Wall Furnace (FAW55) Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents