NAPOLEON GPFN-2 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

EN
FR
PG.23
www.napoleongrills.com
N415-0359 JUN 12.18
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
DANGER
IF YOU SMELL GAS:
Shut o gas to the appliance.
Exnguish any open ame.
If odor connues, keep away from the
appliance and immediately call your gas
supplier or re department.
DANGER! CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide, which has no odor. Using it in an
enclosed space can kill you. Never use this appliance in an enclosed space such
as a camper, tent, car or home.
WARNING! For Outdoor Use Only.
AVERTISSEMENT
Ne tentez pas d’allumer cet appareil avant
d’avoir lu la secon «INSTRUCTIONS
D’ALLUMAGE» de ce manuel.
Pour votre sécurité, n’entreposez pas et
n’ulisez pas d’essence ou autres liquides
et vapeurs inammables à proximité de cet
ou tout autre appareil. Une bonbonne de
propane non branchée ne devrait pas être
entreposée à proximité de cet ou de tout
autre appareil. Si ces instrucons ne sont pas
suivies à la lere, un feu ou une explosion
pourraient s’ensuivre, causant des dommages
à la propriété, des blessures corporelles ou
des pertes de vie.
This gas appliance must be used only outdoors in a well-venlated space and must not be used
inside a building, garage, screened-in porch, gazebo or any other enclosed area.
APPLY SERIAL NUMBER LABEL FROM CARTON
Serial No.
XXXXXX000000
MODEL NO.
Wolf Steel Ltd.
214 Bayview Drive,
Barrie, Ontario, CANADA L4N 4Y8
PATIOFLAME
OUTDOOR GAS FIREPLACE
GPFN NATURAL GAS
GPFP PROPANE
2
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Should deterioration of parts occur to the degree of non-performance (rusted
through or burnt through) within the duration of the warranted coverage, a
replacement part will be provided. The replacement component is the sole
responsibility of NAPOLEON defined by this Limited Warranty; in no event will
NAPOLEON be responsible for installation, labor or any other costs or expenses
related to the re-installation of a warranted part, for any incidental,
consequential, or indirect damages or for any transportation charges, labor costs
or export duties.
This Limited Warranty is provided in addition to any rights afforded to you by local
laws. Accordingly, this Limited Warranty imposes no obligation upon NAPOLEON
to keep parts in stock. Based on the availability of parts, NAPOLEON may at its
discretion discharge all obligations by providing a customer a prorated credit
towards a new product. After the first year, with respect to this Limited Warranty
NAPOLEON may, at its discretion, fully discharge all obligations with respect to
this warranty by refunding to the original warranted purchaser the wholesale price
of any warranted but defective part(s).
The bill of sale or copy will be required together with a serial number and a model
number when making any warranty claims from NAPOLEON.
NAPOLEON reserves the right to have its representative inspect any product or part
prior to honoring any warranty claim. You must contact NAPOLEON Customer Service
or an authorized NAPOLEON dealer to obtain the benefit of the warranty coverage.
napoleongrills.com
Napoleon President’s 3 Year Limited Warranty
NAPOLEON products are designed with superior components and materials, and are assembled by trained
craftsmen who take great pride in their work. This product has been thoroughly inspected by a qualified
technician before packaging and shipping to ensure that you, the customer, receive the quality product you
expect from NAPOLEON.
NAPOLEON warrants that components in your new NAPOLEON product will be free from defects in material and
workmanship from the date of purchase, for the following period:
* Conditions and Limitations
This Limited Warranty creates a warranty period as specified in the
aforementioned table, for any product purchased through an authorized NAPOLEON
dealer, and entitles the original purchaser to the specified coverage in respect of
any component replaced within the warranty period, either by NAPOLEON or an
authorized NAPOLEON dealer, to replace a component of such product that has
failed in normal private use as a result of a manufacturing defect. The “50% off”
indicated in the table means the component is made available to the purchaser at
a 50% discount off the regular retail price of the component for the period
indicated. This Limited Warranty does not cover accessories or bonus items.
For greater certainty, “normal private use” of a product means that the product:
has been installed by a licensed, authorized service technician or contractor, in
accordance with the installation instructions included with the product and all
local and national building and fire codes; has been properly maintained; and has
not been used as a communal amenity or in a commercial application.
Similarly, “failure” does not include: over-firing, blow outs caused by
environmental conditions such as strong winds or inadequate ventilation,
scratches, dents, corrosion, deterioration of painted and plated finishes,
discoloration caused by heat, abrasive or chemical cleaners or UV exposure,
chipping of porcelain enameled parts, or damages caused by misuse, accident,
hail, grease fires, lack of maintenance, hostile environments such as salt or
chlorine, alterations, abuse, neglect or parts installed from other manufacturers.
Aluminum table top and pedestal ...................................................... 3 years
Stainless steel housing ......................................................................3 years
Stainless steel burner assembly ........................................................ 3 years
All other parts .................................................................................... 2 years
3
EN
www.napoleongrills.com
N415-0359 JUN 12.18
WARNING! For Outdoor Use Only.
WARNING! Improper installaon, adjustment, alteraon, service or maintenance can cause injury
or property damage. Read the installaon, operang and maintenance instrucons thoroughly before
installing or servicing this gas appliance.
Safe Operang Pracces
THIS APPLIANCE IS HOT WHEN OPERATING AND CAN CAUSE SEVERE BURNS IF CONTACTED.
Installaon and repair should be done by a qualied service person. The appliance should be
inspected before use and at least annually by a qualied service person. More frequent cleaning
may be required as necessary. It is imperave the control compartment, burners and circulang air
passageways of the appliance be kept clean.
Do not operate appliance before reading and understanding operang instrucons. Failure to operate
appliance according to operang instrucons could cause re or injury.
Risk of burns. The appliance should be turned o and cooled before servicing.
Do not install damaged, incomplete or substute components.
Young children should be carefully supervised when they are in the area of the appliance. Toddlers,
young children and others may be suscepble to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the vicinity. To restrict access to an appliance or
stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals
out of the vicinity and away from hot surfaces.
Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching
hot surfaces.
Under no circumstances should this appliance be modied.
Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plasc bags, these are not toys and should be kept away from children and infants.
Do not leave appliance unaended when in use.
For Outdoor use only.
This appliance must not be used for cooking.
This unit is not for use with solid fuel.
Improper installaon, adjustment, alteraon, service, or maintenance can cause injury or property
damage. Read the installaon, operang and maintenance instrucons thoroughly before installing or
servicing this equipment.
This appliance shall be used ONLY outdoors in a well-venlated space and shall NOT be used inside a
building, garage, or any other enclosed area.
Cylinders must be stored outdoors in a well-venlated area out of reach of children. Disconnected
cylinders must have threaded valve plugs ghtly installed and must not be stored in a building, garage
or any other enclosed area.
Storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply
(natural gas line or LP gas cylinder).
If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the
appliance being put into operaon.
Clothing or other ammable materials should not be hung from the appliance, or placed on or near
the appliance.
Any guard or other protecve device removed for servicing the appliance must be replaced prior to
operang the appliance.
Inspect the fuel supply connecon for signs of leakage (including the hose for LP models) before each
use of the appliance.
The pressure regulator and hose assembly supplied with LP models must be used. Replacement
pressure regulators and hose assemblies must be those specied in this manual.
The LP gas supply cylinder used with LP models must be constructed and marked in accordance with
the specicaons for LP-gas cylinders as required by the U.S. Department of Transportaon (DOT) or
the Canadian Transport Commission (CTC).
The LP gas cylinder supply system must be arranged for vapour withdrawal.
The LP-gas cylinder used must include a collar to protect the cylinder valve.
When an LP model is not in use, the LP-gas must be turned o at the supply cylinder.
To extend the life of your appliance, protect and cover it from the elements when not in use.
This product must be installed by a licensed plumber or gas er when installed within the
commonwealth of Massachuses.
4
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Geng Started
1. Remove all of the parts from the carton. Use the parts list to ensure all necessary parts are included.
2. Do not destroy packaging unl the appliance has been installed and operates to your sasfacon.
3. Choose a locaon that meets the clearance to combusbles as outlined in this manual. Take into
consideraon the need for clear and easy access to the on/o valve AFTER the appliance is installed
and connected to the gas supply in order to safely turn o the burner.
4. Most stainless steel parts are supplied with a protecve plasc coang that must be removed prior
to using the appliance. The protecve coang has been removed from some of the parts during the
manufacturing process and may have le behind a residue that can be perceived as scratches or
blemishes. To remove the residue, vigorously wipe the stainless steel in the same direcon as the grain.
5. Read and follow all instrucons in this manual before installing or servicing this gas appliance.
If you have any quesons about assembly or appliance operaon, or if there are damaged or missing
parts please call our Customer Soluons Department at 1-866-820-8686 between 9 AM and 5 PM
(Eastern Standard Time).
WARNING! This appliance is designed for non-combusble enclosures only, and must be installed
and serviced by a qualied installer to local codes.
General Informaon
This gas appliance was tested and listed to Canadian and American Naonal Standards, ANSI Z21.97-2012
/ CSA 2.41-2012 “Standard for Outdoor Decorave Gas Appliance”. When an appliance is for connecon
to a xed piping system, the installaon must conform with local codes, or in the absence of local codes,
with the Naonal Fuel Gas Code, ANSI Z223.1/NFPA 54, Internaonal Fuel Gas Code, Natural Gas and
Propane Installaon Code, CSA B149.1, or Propane Storage and Handling Code, B149.2, as applicable.
This appliance should be installed and serviced by a qualied installer to conform according to local codes.
Installaon pracces vary from region to region and it is important to know the specics that apply to your
area, for example: in Massachuses State:
The appliance o valve must be a “T” handle gas cock.
The exible connector must not be longer than 36 inches.
The appliance and its individual shut o valve must be disconnected from the gas supply piping system
during any pressure tesng of the system at test pressures in excess of 1/2 psig (3.5kPa).
This appliance must be isolated from the gas supply piping system by closing its individual manual shut o
valve during any pressure tesng of the gas supply piping system at test pressures equal to or less than 1/2
psig (3.5kPa).
The following clearances to combusble materials must be maintained:
Sides (all around) - 24 inches (610mm)
Top - 72 inches (1830mm)
Always keep the appliance area clear and free
from combusble materials, gasoline, and
other ammable vapors and liquids.
Do not locate appliance where it can get
excessively wet.
Do not use this appliance if any part has been
under water. Immediately call a qualied
service technician to inspect the unit and to
replace any part of the control system and any
gas control, which has been underwater.
California Proposion 65: This product can expose you to chemicals including lead and lead compounds,
which are known to the State of California to cause cancer, and chemicals including carbon monoxide,
which are known to the State of California to cause birth defects or other reproducve harm. For more
informaon go to www.P65Warnings.ca.gov.
5
EN
www.napoleongrills.com
N415-0359 JUN 12.18
DIMENSIONS
Specicaons
INPUT
MODEL FUEL MAX. INPUT Btu/Hr
GPFN Natural Gas 60, 000
GPFP Propane Gas 60, 000
GAS INLET PRESSURES
NATURAL PROPANE
Maximum Inlet Pressure 7.0" w.c. 11.0" w.c.
MINIMUM CLEARANCE TO COMBUSTIBLES
INCHES MM
Side Walls 24 610
Top of unit to ceiling 72 1830
6
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Locaon
Locang Your Outdoor Appliance
It is important when selecng a locaon for your appliance to ensure clearances to adjacent combusbles
are met. This appliance is intended for installaon on an outdoor pao or in your yard. It is highly
recommended that this appliance be installed in a sheltered area (following the guidelines outlined
below). Direct wind will cause an errac ame and possible pilot or main burner outage. An errac
ame could also lead to excessive carboning (black soot), this condion is not a safety issue but is visually
undesirable.
Note: When choosing a locaon for your appliance, care must be taken to avoid areas where excessive
moisture or running water may be a problem.
Any enclosure (shelter) in which the appliance is used must comply with one of the following:
With walls on all sides, but at least one permanent opening at ground level and no overhead cover.
Within a paral enclosure which includes an overhead cover and no more than two sidewalls. These
sidewalls may be parallel, as in a breezeway, or at right angles to each other.
Within a paral enclosure which includes an overhead cover and three sidewalls, as long as 30 percent or
more of the horizontal periphery of the enclosure is permanently open.
7
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Gas Hook-Up Instrucons
Manual Gas
Valve (on/off)
Burner Assembly
Natural Gas Hook-Up
The gas appliance is designed to operate at an inlet pressure of 7 inches water column. The piping up to
the appliance is the responsibility of the installer. Connect the inlet valve to rigid pipe, copper tube or an
approved exible metal connector, which complies with Z21.4/CSA 6.10. If using a gas hose (not supplied)
connect the ared end of the hose to the connector on the end of the inlet valve. Tighten using two
wrenches. (Do not use thread sealer/pipe dope.) Leak test all joints prior to using the appliance. Piping
and valves upstream of the quick disconnect are not supplied. The gas supply pipe must be suciently
sized to supply the BTU/h specied on the rang plate, based on the length of the piping run. The quick
disconnect must not be installed in an upward direcon and a readily accessible manual shut-o valve
must be installed upstream of, and as close to, the quick disconnect as is feasible.
Purge the gas supply line of any trapped air prior to the rst ring of the unit.
WARNING!
The installaon must be performed by a licensed gas er, and all connecons must be leak tested
before operang the appliance.
Ensure all hose connecons are ghtened using two wrenches. Do not use Teon tape or pipe dope
on any hose connecon.
Ensure the hose does not contact any high temperature surfaces or it may melt and leak causing a
re.
Locate the hose out of pathways where people may trip over it or in areas where the hose may be
subject to accidental damage.
Leak test all the connecons using a soap and water soluon as indicated in the diagrams.
Installaon
DO NOT USE AN OPEN FLAME.
WARNING! When the appliance is being used with the oponal tripod, it must not be situated on
a combusble surface, nor can it be located below a combusble overhang.
The log set and the burner assembly are shipped together.
Remove the gas log set and burner assembly and check for damage. DO NOT install damaged
components. The logs are fragile use care when handling.
Place the appliance on a level/secure surface in desired locaon. This locaon must be adjacent to the
gas supply line or cylinder.
NOTE: Minimum clearances to combusble construcon must be maintained, see "SPECIFICATIONS"
secon.
WARNING! You must have clear and easy access to the on/o valve AFTER the appliance is
installed and connected to the gas supply in order to safely turn o the burner.
THE ON/OFF GAS VALVE IS USED TO TURN THE BURNER ON AND OFF.
8
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Cylinder Connecon: Ensure the gas regulator hose is kink free. Remove the cap or plug from the cylinder
fuel valve. Insert the black QCC1 regulator nipple onto the QCC1 fuel valve. Hand ghten clockwise. Do not
use tools. Leak test all joints prior to using the appliance. A leak test must be performed annually and each
me a cylinder is hooked up or if a part of the gas system is replaced.
If this appliance is to be connected directly to a house propane gas supply line, follow the instrucons
for the natural gas hook-up.
CAUTION!
Make sure cylinder valve is in its full o posion. (Turn clockwise to stop).
Check cylinder valve features to ensure it has proper external mang threads. (Cylinder Valve Marked:
USE WITH TYPE 1)
Inspect hose shipped with the unit for damage. Never aempt to use damaged or plugged equipment.
See your local LP Gas Dealer for repairs.
When connecng regulator assembly to the cylinder valve, hand ghten black QCC1 nut clockwise to a
posive stop. DO NOT use a wrench to ghten. Use of a wrench may damage the quick closing coupling
nut and result in a hazardous condion.
Locate the hose out of pathways where people may trip over
it or in areas where the hose may be subject to accidental
damage.
Open cylinder valve fully (counter-clockwise). Turn the on/
o valve at the unit slowly to the on posion and use a soapy
water soluon to check all connecons for leaks as indicated
in the diagrams before aempng to light the appliance. If a
leak is found, turn tank valve o and do not use the appliance
unl repairs can be made.
WARNING! If these instrucons are not followed exactly, a re causing death or serious injury may
occur.
Propane Cylinder Specicaons
A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a
cylinder with a damaged valve. The LP-gas supply cylinder must be constructed and marked in accordance
with the U.S. D.O.T. Specicaons for LP-Gas Cylinders or the Standard for Cylinders, Spheres and Tubes for
Transportaon of Dangerous Good and Commission, CAN/CSA-B339, as applicable.
This appliance has been designed for use with a 20 lb. (9.1 kg) or 30 lb (13.6 kg) size propane cylinder only
(not supplied).
The LP-gas supply cylinder must be provided with a cylinder-connecon device compable with the
connecon for the appliance. The propane cylinder must be provided with a shut-o valve terminang in
a propane cylinder valve type QCC1, and a safety relief device having direct communicaon with the vapor
space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and the cylinder
shall include a collar to protect the cylinder valve. The LP-gas cylinder must be provided with a listed
overll protecon device (OPD). Do not store a spare LP-gas cylinder under or near this appliance. Never
ll the cylinder beyond 80 percent full.
Use only the pressure regulator and hose assembly provided with this appliance. Replacement pressure
regulators and hose assemblies must be specied by the manufacturer. The regulator supplies a pressure
of 11 inches. water column to the appliance and has a QCC1 type ng. Cylinders to be used with this
unit must be supplied with a QCC1 cylinder valve. A QCC1 cylinder has a posive seang connecon,
which will not allow gas ow unl a posive seal has been achieved. It is also equipped with an excess ow
device. In order to aain full ow to the appliance, the valve must be in the o posion when the cylinder
valve is turned on.
WARNING! A re will result if the gas supply hose makes contact with the underside of the
appliance.
Manual Gas
Valve (on/off)
Burner Assembly
Cylinder Retaining
Bracket
DO NOT USE AN OPEN FLAME.
9
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Cylinder Retaining Bracket
1. Fasten the bracket to the boom of the propane bole using
bolt and nut supplied.
2. Tighten the lag screw into the mounng surface
leaving approxi
mately 1/4” (6mm) of thread above the
surface.
3. Slide propane bole into posion so that the bracket slides
under the head of the lag screw.
4. Tighten the lag screw onto the bracket.
5. For fastening to a concrete surface a concrete anchor will be
required. (Not supplied)
Enclosures For LP (Propane) Gas Supply Systems
If you build an enclosure for an LP gas cylinder, follow these recommended specicaons. You must also
follow local codes.
An enclosure for an LP-gas cylinder shall be venlated by openings at both the upper and lower levels
of the enclosure.
This shall be accomplished by one of the following:
One side of the enclosure shall be completely open;
OR
For an enclosure having four sides, a top, and a boom:
a) At least two venlaon openings shall be provided in the sidewalls of the enclosure, located within 5 in
(127 mm) of the top of the enclosure, equally sized, spaced at a minimum of 90 degrees (1.57 rad), and
unobstructed. The opening(s) shall have a total free area of not less than 1 in
2
per lb (14.2 cm
2
/ kg) of
stored fuel capacity.
b) Venlaon opening(s) shall be provided at oor level of the enclosure and shall have a total free area of
not less than 1/2 in
2
per lb (7.1 cm
2
/ kg) of stored fuel capacity. If venlaon openings at oor level are in
a side wall, there shall be at least two openings. The boom of the openings shall be 1 in (25.4 mm) or less
from the oor level and the upper edge no more than 5 in (127 mm) above the oor level. The openings
shall be equally sized, spaced at a minimum of 90 degrees (1.57 rad), and unobstructed.
c) Every opening shall have minimum dimensions so as to permit the entrance of a 1/8 inch (3.2mm)
diameter rod.
Venlaon openings in sidewalls shall not communicate directly with other enclosures of the
appliance.
Cylinder valves shall be readily accessible for hand operaon. A door on the enclosure to gain access to
the cylinder valve is acceptable, provided it is non-locking and can be opened without the use of tools.
Designs using a cover to gain access to the cylinder and cylinder valve shall be provided with handles or
equivalent at a minimum of 180 degrees apart to facilitate liing of the cover.
There shall be a minimum clearance of 2 inches (50.8mm) between the lower surface of the oor of the LP
gas supply cylinder enclosure and the ground.
The design of the enclosure shall be such that (1) the LP gas supply cylinder(s) can be connected,
disconnected and the connecons inspected and tested outside the cylinder enclosure; and (2) those
connecons which could be disturbed when installing the cylinder(s) in the enclosure can be leak tested
inside the enclosure.
The enclosure for the LP-gas cylinder
shall isolate the cylinder from the burner
compartment to provide:
a. Shielding from radiaon;
b. A ame barrier; and
c. Protecon from foreign material.
Be certain to mount or set the LP gas cylinder
on a at surface and restrain it using a cylinder
retaining bracket to prevent it from pping.
Natural Gas
Supply Line
(not supplied)
Propane Regulator
Hose
Manual Gas
Valve (on/off)
QCC1
Cylinder Retaining
Bracket
10
EN
www.napoleongrills.com
N415-0359 JUN 12.18
CYLINDER SIZE OPENING A AREA OPENING B AREA
20 lb (9.1kg)
20in
2
(130cm
2
) 10in
2
(65cm
2
)
30 lb (13.6kg)
30in
2
(195cm
2
) 15in
2
(100cm
2
)
5” (127mm)
MAXIMUM
1” (25.4mm)
MAXIMUM
OPENING
A
OPENING
B
2” (51mm)
MINIMUM
PARTITION TO ISOLATE
CYLINDER FROM GRILL
NON LOCKING DOOR
34” (864mm)
RECOMMENDED
5” (127mm)
MAXIMUM
11
EN
www.napoleongrills.com
N415-0359 JUN 12.18
LOG PLACEMENT / AGGREGATE
The appliance is supplied with 3lbs of lava rock. All 3lbs can be poured into outer ring. It may be mixed,
or layered with desired aggregate on top. DO NOT PLACE AGGREGATE ONTO BURNER.
Finishing
BASE LOG
#1
#2
#3
#4
AGGREGATE
Set base log onto burner ensuring stud and
bracket t into hole and notch. Base log should
sit at on “Paoame” base.
Place “Y” end of log #1 into “Y” notch on the
base log.
Place pocket on log #2 onto the locator on the
base log.
Hook log #3 into notch on base log.
Place log #4 into notch on base and pocket on
log #3.
12
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Finishing
Notched
Rock
MKR Rock Installaon (Oponal)
WARNING! Real rocks must not be used in this appliance. Heat will cause them to explode.
1. Remove the refactpry logs and lava rocks from your appliance.
2. Place the 4 notched rocks and 2 clusters on the edge of the burner pan as shown, making sure not to
cover any ports.
3. Place the remaining refractory rocks on and around the burner as desired. (There are not set
locaons).
4. Spread the lava rock removed in Step 1 and evenly distribute it around the rocks.
Glass Ember Installaon
WARNING! Glass embers may have sharp edges, wear safety glasses and gloves when handling.
Do not change or substute the glass ember material provided with this appliance. If replacing, use
only replacement glass embers available from your local authorized dealer / distributor.
WARNING! Glass embers may have a ne oil residue that needs to be cleaned prior to installaon.
Clean the glass with mild dish soap, drain, rinse thoroughly and dry before installing.
1. Remove the refractory logs and lava rocks from your appliance.
2. Carefully pour 3 bags of the appliance glass media onto the appliance log support as shown.
3. Spread the glass evenly over the pan burner. The distribuon of clear glass over the burner pan will
inuence ame height.
13
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Leak Tesng Instrucons
WARNING! A leak test must be performed annually, or if a part of the gas system is replaced.
WARNING! Never use an open ame to check for gas leaks. Be certain no sparks or open ames
are in the area while you check for leaks. Sparks or open ames will result in a re or explosion,
damage to property, serious bodily injury, or death.
Leak tesng: This must be done before inial use, annually, and whenever any gas components are
replaced or serviced. Do not smoke while performing this test, and remove all sources of ignion. See Leak
Tesng Diagram for areas to check. Turn all burner controls to the o posion. Turn gas supply valve on.
Brush a half-and-half soluon of liquid soap and water onto all joints and connecons of the regulator,
hose, manifolds and valves.
Bubbles will indicate a gas leak. Either ghten the loose joint or have the part replaced with one
recommended by the Napoleon Customer Soluons department and have the appliance inspected by a
cered gas installer.
If the leak cannot be stopped, immediately shut o the gas supply, disconnect it, and have the grill
inspected by a cered gas installer or dealer. Do not use the appliance unl the leak has been corrected.
Manual Gas
Valve (on/off)
Burner Assembly
Cylinder Retaining
Bracket
DO NOT USE AN OPEN FLAME.
Manual Gas
Valve (on/off)
Burner Assembly
DO NOT USE AN OPEN FLAME.
Propane
Natural Gas
14
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Lighng Instrucons
WARNING! If you do not follow these instrucons exactly a re or explosion may result causing
property damage, personal injury or loss of life.
WARNING! Keep face and body away from burner area when lighng.
Upon compleng the gas line connecon, a small amount of air will be in the lines. When rst lighng the
burner, it will take a few seconds for the lines to purge themselves of this air.
Once the purging is complete, the burner will light and operate as indicated in the instrucon manual.
Subsequent lighng of the appliance will not require such purging unless the gas supply has been
disconnected.
1. Locate the manual gas control valve.
2. Hold a lit long match or long butane lighter near the burner ports on top of the burner. For a
Natural Gas unit, turn on the ON/OFF valve slowly at the unit. For a LP unit, turn the valve in the LP
tank counter clockwise all the way and then turn on the ON/OFF valve slowly at the unit.
3. If the burner does not light within 10 seconds, turn the valve o and wait 5 minutes for any gas
to dissipate before repeang the procedure.
4. To shut down the burner turn the burner control knob clockwise to the o posion. Then turn
the gas o at the source (propane cylinder valve or natural gas supply valve).
Note: The propane regulator in this appliance is equipped with a low ow protecon device. Unless
the propane cylinder valve is opened before the appliance valve, the gas ow will be reduced resulng
in a very small ame. To reset this device, shut o the appliance valve, then the propane cylinder valve.
Next, diconnect the regulator adaptor from the tank and then reconnect. Follow the lighng procedure
ensuring the propane cylinder valve is opened before the unit is.
Manual Gas
Valve (on/off)
Burner Assembly
15
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Operang The Pao Flame
Inial Lighng: When lit for the rst me, the appliance emits a slight odor. This is a normal temporary
condion caused by the “burn-in” of internal paints and lubricants used in the manufacturing process and
does not occur again. Simply run the main burner on high for approximately one-half hour.
WARNING!
Children and adults should be alerted to the hazards of high surface temperatures and should stay
away from the appliance to avoid burns or clothing ignion.
Children should be carefully supervised when they are in the area of the appliance.
Clothing or other ammable materials should not be hung from the appliance, or placed on or near
the appliance. The area above the enclosure may be extremely hot. Direct contact with these
surfaces should be avoided in order to prevent burns or clothing ignion.
Any guard or protecve device removed for servicing the appliance must be replaced prior to
operang the appliance.
Installaon and repair should be done by a qualied service person. The appliance should be
inspected before each use and at least annually by a qualied service person. More frequent
cleaning may be required as necessary. It is imperave that the control compartment, burners and
circulang air passageways of the appliance be kept clean.
WARNING!
Never use the appliance while it is raining.
Always turn the appliance o when raining.
Never splash any liquid on the glass / glass embers when the appliance is operang.
The glass / glass embers will be extremely hot while operang, never try to touch them.
Always ensure the appliance stands rmly on level ground.
Never use the appliance if the burner is damaged. Inspect the burner before each use. Ensure that
no debris such as leaves; grass or other objects have entered or are on the appliance. If the burner
is damaged it must be replaced prior to using the appliance with a replacement burner specied by
your Napoleon dealer.
Inspect the hose assembly before each use. If there is evidence of excessive abrasion or wear, or if
the hose is damaged it must be replaced prior to using the appliance with a replacement hose as-
sembly specied by your Napoleon dealer.
WARNING! Any modicaon to the appliance may compromise the safety of this appliance.
Do not operate the appliance if any part has been under water. Immediately call a qualied service
technician to inspect the appliance and replace any part of the control system and any gas control,
which has been underwater.
WARNING! You must have clear and easy access to the on/o valve AFTER the appliance is
installed and connected to the gas supply in order to safely turn o the burner.
WARNING! Never use this appliance for other than the intended use. Do not use this appliance to
prepare food.
16
EN
www.napoleongrills.com
N415-0359 JUN 12.18
WARNING! Glass embers may have sharp edges, wear safety glasses and gloves when handling.
Do not change or substute the glass ember material provided with this appliance. If replacing, use
only replacement glass embers available from your local authorized dealer / distributor.
WARNING! To avoid the possibility of burns, maintenance should be done only when the
appliance is . Avoid unprotected contact with hot surfaces. Ensure burner is turned o. Turn gas o at
source and disconnect the appliance before servicing. Clean the appliance in an area where cleaning
soluons will not harm decks, lawns, or paos. Do not use ammable, corrosive or abrasive cleaners.
Note: Stainless steel tends to oxidize or stain in the presence of chlorides and suldes, parcularly in
coastal areas and other harsh environments, such as the warm, highly humid atmosphere around pools
and hot tubs. These stains could be perceived as rust, but can be easily removed or prevented. To provide
stain prevenon and removal, wash all stainless steel and chrome surfaces every 3-4 weeks or as oen as
required with fresh water and/or stainless steel cleaner.
Maintenance / Cleaning Instrucons
Burner: The burner is made from stainless steel, but extreme heat and a corrosive environment can cause
surface corrosion to occur. This can be removed with a brass wire brush. Inspect the burner at least
annually for cracks, insect nests, excessive corrosion or any other damage. If the burner is damaged, it
must be replaced with a burner specied by the manufacturer before the appliance is put into operaon.
CAUTION! Beware of Spiders.
Spiders and insects are aracted to the smell of propane and natural gas. The burner is equipped with an
insect screen on the air shuer, which reduces the likelihood of insects building nests inside the burner
but does not enrely eliminate the problem. A nest or web can cause the burner to burn with a so yellow
or orange ame or cause a re (ashback) at the air shuer underneath the control panel. Other warning
signs that may indicate a problem are:
Strong or unusual odor coming from the appliance.
Connued diculty or delayed ignion.
Flame appears either very short or very long.
Flame only burns part way across the burner.
Excessive soot building up on the glass embers.
To clean the inside of the burner, it must be removed from the appliance: Remove the glass embers and
examine the burner. If dirty, clean with a wire brush.
Cleaning: Use a exible venturi tube brush to clean the inside of the burner. Shake any loose debris from
the burner through the gas inlet. Check the burner ports and valve orices for blockages. Burner ports can
close over me due to debris and corrosion; use an opened paperclip or a drill bit to clean them. The ports
are easier to clean if the burner is removed from the appliance, but it can also be done with the burner
installed.
Reinstallaon: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when
installing. Replace the glass embers. When the appliance is put back in service, check the burner ame
paern with the image below.
WARNING! Hose: Check for abrasions, melng, cuts, and cracks in the hose. If any of these
condions exist, do not use the appliance. Have the part replaced by your Napoleon dealer or qualied
gas installer.
Cleaning Inside The Appliance: While washing your appliance, be sure to keep the area around the burner
and pilot assembly dry at all mes.
WARNING! If the gas control is exposed to water in any way, DO NOT try to use the appliance.
The gas control must be replaced.
17
EN
www.napoleongrills.com
N415-0359 JUN 12.18
High Elevaon Installaon
This listed gas appliance is tested and approved for elevaons from 0 to 4500 feet in Canada and the U.S.
When installing this appliance at an elevaon above 4500 feet (in the U.S.), it may be necessary to
decrease the input rang by changing the exisng burner orice to a smaller size. Input should be reduced
four percent (4%) for each 1,000 feet beyond the 4,500 feet above sea level, unless the heang value of
the gas has been reduced, in which case this general rule will not apply. To idenfy the proper orice size,
check with the local gas ulity.
When installing this unit at an elevaon above 4,500 feet (in Canada), check with local authories.
Consult your local gas ulity for assistance in determining the proper orice for your locaon.
NORMAL
ABNORMAL
Cleaning The Outer Appliance Surface: Do not use abrasive cleaners or steel wool on any painted, or
stainless steel parts of your Napoleon Appliance. Doing so will scratch the nish. Exterior surfaces should
be cleaned with warm soapy water. To clean stainless surfaces, use a stainless steel or a non-abrasive
cleaner. Always wipe in the direcon of the grain. Over me, stainless steel parts discolor when heated,
usually to a golden or brown hue. This discoloraon is normal and does not aect the performance of the
appliance
WARNING! The appliance area must be clear and free from combusble materials, gasoline and
other ammable vapors and liquids. Do not obstruct the ow of combuson and venlaon air. Keep
the venlaon opening of the cylinder enclosure free and clear of debris.
18
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Troubleshoong
Problem Possible Causes Soluon
Low heat / Low ame
when valve turned on.
For propane - improper
lighng procedure.
For natural gas - undersized
supply line.
Ensure lighng procedure is
followed carefully. The valve
must be in the o posion
when the tank valve is turned
on. Turn tank on slowly to allow
pressure to equalize. See lighng
instrucons.
Pipe must be sized according to
installaon code.
Burners burn with
yellow ame,
accompanied by the
smell of gas.
Possible spider web or
other debris.
Thoroughly clean burner venturi.
See general maintenance
instrucons.
Burner will not stay
lit .
Too windy. Unit will shut down if winds are
greater than 10mph (16km/h).
Either locate to dierent area or
use when it is less windy.
Humming regulator. Normal occurrence on hot
days.
This is not a defect. It is caused
by internal vibraons in the
regulator and does not aect the
performance or safety of the gas
heater. Humming regulators will
not be replaced.
19
EN
www.napoleongrills.com
N415-0359 JUN 12.18
Problem Possible Causes Soluon
Burner output on
“high” seng is
too low. (Rumbling
noise and uering
blue ame at burner
surface.)
Lack of gas.
Supply hose is pinched.
Dirty or clogged orice.
Spider webs or other
maer in venturi tube.
Propane regulator in “low
ow” state.
Check gas level in propane
cylinder.
Reposion supply hose as
necessary.
Clean burner orice.
Clean out venturi tube.
Ensure lighng procedure is
followed carefully. All valves
must be in the o posion
when the tank valve is turned
on. Turn tank on slowly to allow
pressure to equalize. See lighng
instrucons.
20
EN
www.napoleongrills.com
N415-0359 JUN 12.18
COMPONENTS
REF PART NO. DESCRIPTION
1 QA-047 OUTER BASE
2 W655-0176 LOG SUPPORT
3 W010-1030 BURNER ASSEMBLY
4 W080-0618 ORIFICE BRACKET
5 W455-0076 PROPANE ORIFICE - #43
N455-0082 NATURAL GAS ORIFICE - 1/8”
6 GL-640 LOG SET
7 W135-0189 BASE LOG
8 W135-0190 LOG #1
9 W135-0191 LOG #2
10 W135-0192 LOG #3
11 W135-0193 LOG #4
12 W175-0210 FLEX c/w SHUT OFF - STAINLESS STEEL
13 W530-0023 PROPANE REGULATOR / HOSE ASSEMBLY (LP UNITS ONLY)
* W550-0005 AGGREGATE LAVA ROCK
ACCESSORIES
REF PART NO. DESCRIPTION
14 W320-0014 WIRE GUARD
* N345-0001 NATURAL GAS HOSE 10FT
* PFS SAFETY SCREEN
* PFT PATIO FLAME TABLE
* PFTT-GK GRANITE TABLE TOP
* MKRY GREY RIVER ROCKS
* MKRM MULTI-COLOURED RIVER ROCKS
* MKGC GLASS EMBERS - CLEAR
* MKGK GLASS EMBERS - BLACK
* MKGB GLASS EMBERS - BLUE
* MKGR GLASS EMBERS - RED
* MKGA GLASS EMBERS - AMBER
KEEP YOUR RECEIPT AS PROOF OF PURCHASE TO VALIDATE YOUR WARRANTY.
Ordering Replacement Parts
Warranty Informaon
MODEL:
DATE OF PURCHASE:
SERIAL NUMBER:
(Record informaon here for easy reference)
For replacement parts and warranty claims, contact the Napoleon dealer where the product was purchased.
Before contacng the dealer, check the Napoleon Grills Website for more extensive cleaning, maintenance,
troubleshoong and parts replacement instrucons at www.napoleongrills.com.
To process a claim, the following informaon is required:
1. Model and serial number of the unit.
2. Part number and descripon.
3. A concise descripon of the problem (‘broken’ is not sucient).
4. Proof of purchase (photocopy of the invoice).
In some cases, Napoleon could request to have the parts returned to the factory for inspecon before
providing replacement parts.
Before contacng Napoleon dealer, please note that the following items are not covered by the warranty:
Costs for transportaon, brokerage or export dues.
Labour costs for removal and reinstallaon.
Costs for service calls to diagnose problems.
Discolouraon of stainless steel parts.
Part failure due to lack of cleaning and maintenance, or use of improper cleaners (oven
cleaner or other harsh chemicals).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

NAPOLEON GPFN-2 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues