30" AND 36" (76.2 CM AND 91.4 CM)
TOUCH CONTROL AND KNOB CONTROL
RADIANT COOKTOP
TABLE DE CUISSON RADIANTE
À COMMANDES TACTILES ET COMMANDES
À BOUTONS 30" ET 36" (76,2 CM ET 91,4 CM)
W10848426B
Use & Care Guide
For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:
1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.
In Canada, call: 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.
Guide d’utilisation et d’entretien
Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, accessoires ou dépannage,
composer le : 1-800-JENNAIR (1-800-536-6247) ou visitez notre site web à www.jennair.com.
Au Canada, composer le : 1-800-JENNAIR (1-800-536-6247) ou visitez notre site web à www.jennair.ca.
2
TABLE OF CONTENTS TABLE DES MATIÈRES
COOKTOP SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
COOKTOP SAFETY ........................................................................ 2
PARTS AND FEATURES – ELECTRONIC
TOUCH CONTROLS ....................................................................... 4
COOKTOP CONTROLS – ELECTRONIC
TOUCH CONTROLS ....................................................................... 5
Cooktop Controls .........................................................................5
Dual/Triple Element ......................................................................6
Control Lock .................................................................................6
PARTS AND FEATURES – KNOB CONTROLS ............................7
COOKTOP CONTROLS – KNOB CONTROLS .............................8
Cooktop Controls .........................................................................8
Dual/Triple Circuit Element ........................................................... 8
COOKTOP USE ..............................................................................9
Downdraft Ventilation System ...................................................... 9
Home Canning .............................................................................9
Cookware .....................................................................................9
Ceramic Glass ............................................................................10
COOKTOP CARE ..........................................................................11
General Cleaning ........................................................................11
TROUBLESHOOTING ..................................................................13
ASSISTANCE OR SERVICE .........................................................14
In the U.S.A. ...............................................................................14
In Canada ...................................................................................14
Accessories ................................................................................14
WARRANTY ..................................................................................15
SÉCURITÉ DE LA TABLE DE CUISSON .....................................17
PIÈCES ET CARACTÉRISTIQUES –
COMMANDES ÉLECTRONIQUES TACTILES ...........................19
COMMANDES DE LA TABLE DE CUISSON –
COM - MANDES ÉLECTRONIQUES TACTILES ........................20
Commandes de la table de cuisson ..........................................20
Éléments double/triple ...............................................................21
Verrouillage des commandes .....................................................21
PIÈCES ET CARACTÉRISTIQUES –
COMMANDES À BOUTONS ........................................................22
COMMANDES DE LA TABLE DE CUISSON –
COMMANDES À BOUTONS ........................................................23
Commandes de la table de cuisson ..........................................23
Élément à double/triple circuit ...................................................24
UTILISATION DE LA TABLE DE CUISSON ................................25
Système de ventilation avec aspiration par le bas ....................25
Préparation de conserves à la maison ......................................25
Ustensiles de cuisson ................................................................25
Vitrocéramique ...........................................................................26
ENTRETIEN DE LA TABLE DE CUISSON ..................................27
Nettoyage général ......................................................................27
DÉPANNAGE .................................................................................29
ASSISTANCE OU SERVICE .........................................................30
Aux É.-U. ....................................................................................30
Au Canada ..................................................................................30
Accessoires ................................................................................30
GARANTIE .....................................................................................31
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
3
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the cooktop, follow
basic precautions, including the following:
■ CAUTION: Do not store items of interest to children in
cabinets above a cooktop – Children climbing on the
cooktop to reach items could be seriously injured.
■ Proper Installation – Be sure your cooktop is properly
installed and grounded by a qualified technician.
■ Never Use Your Cooktop for Warming or Heating the
Room.
■ Do Not Leave Children Alone – Children should not be left
alone or unattended in area where cooktop is in use. They
should never be allowed to sit or stand on any part of the
cooktop.
■
Wear Proper Apparel – Loose-fitting or hanging garments
should never be worn while using the cooktop.
■ User Servicing – Do not repair or replace any part of the
cooktop unless specifically recommended in the manual. All
other servicing should be referred to a qualified technician.
■ Storage on Cooktop – Flammable materials should not be
stored near surface units.
■ Do Not Use Water on Grease Fires – Smother fire or flame
or use dry chemical or foam-type extinguisher.
■ Use Only Dry Potholders – Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholder touch hot heating elements. Do not use a towel
or other bulky cloth.
■ DO NOT TOUCH SURFACE UNITS OR AREAS NEAR
UNITS – Surface units may be hot even though they are
dark in color. Areas near surface units may become hot
enough to cause burns. During and after use, do not touch,
or let clothing or other flammable materials contact surface
units or areas near units until they have had sufficient time
to cool. Among those areas are the cooktop and surfaces
facing the cooktop.
■
Use Proper Pan Size – This cooktop is equipped with one
or more surface units of different size. Select utensils
having flat bottoms large enough to cover the surface unit
heating element. The use of undersized utensils will
expose a portion of the heating element to direct contact
and may result in ignition of clothing. Proper relationship of
utensil to burner will also improve efficiency.
■ Never Leave Surface Units Unattended at High Heat
Settings – Boilover causes smoking and greasy spillovers
that may ignite.
■
Glazed Cooking Utensils – Only certain types of glass,
glass/ceramic, ceramic, earthenware, or other glazed
utensils are suitable for cooktop service without breaking
due to the sudden change in temperature.
■
Utensil Handles Should Be Turned Inward and Not Extend
Over Adjacent Surface Units – To reduce the risk of burns,
ignition of flammable materials, and spillage due to
unintentional contact with the utensil, the handle of a
utensil should be positioned so that it is turned inward, and
does not extend over adjacent surface units.
■ Do Not Cook on Broken Cooktop – If cooktop should
break, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock. Contact
a qualified technician immediately.
■ Clean Cooktop With Caution – If a wet sponge or cloth is
used to wipe spills on a hot cooking area, be careful to
avoid steam burn. Some cleaners can produce noxious
fumes if applied to a hot surface.
For units with ventilating hood –
■ Clean Ventilating Hoods Frequently – Grease should not
be allowed to accumulate on hood or filter.
■
When flaming foods under the hood, turn the fan on.
For units with coil elements –
■
Make Sure Reflector Pans or Drip Bowls Are in
Place – Absence of these pans or bowls during
cooking may subject wiring or components
underneath to damage.
■ Protective Liners – Do not use aluminum foil to line surface
unit drip bowls, except as suggested in the manual.
Improper installation of these liners may result in a risk of
electric shock, or fire.
■ Do Not Soak Removable Heating Elements - Heating
elements should never be immersed in water.
4
PARTS AND FEATURES – ELECTRONIC TOUCH CONTROLS
This manual covers different models. The cooktop you have purchased may have some or all of the items listed.
30" (76.2 cm) Control Panel
30" (76.2 cm) Cooktop
36" (91.4 cm) Control Panel
36" (91.4 cm) Cooktop
A. 6" (15.2 cm) single element electronic
touch control
B. 10"/6" (25.4 cm/15.2 cm) dual element
electronic touch control
C. Control lock hold 3 sec
D. 3-speed vent fan electronic touch control
E. 6" (15.2 cm) single element electronic
touch control
F. 9"/6" (22.9 cm/15.2 cm) dual element
electronic touch control
A. 6" (15.2 cm) single element
B. Downdraft vent grille
C. 9"/6" (22.9 cm/15.2 cm)
dual element
D. Control panel
E. 6" (15.2 cm) single element
F. Ceramic cooking surface
G. 10"/6" (25.4 cm/15.2 cm)
dual element
A. 8" (20.3 cm) single element
electronic touch control
B. 6" (15.2 cm) single element
electronic touch control
C. 6" (15.2 cm) single element
electronic touch control
D. 10"/6" (25.4 cm/15.2 cm)
dual element electronic
touch control
E. Control Lock Hold 3 Sec
F. 3-speed vent fan electronic
touch control
G. 12"/9"/6" (30.5 cm/22.9 cm/
15.2 cm) triple element
electronic touch control system
A. 8" (20.3 cm) single element
B. 6" (15.2 cm) single element
C. Downdraft vent grille
D. 12"/9"/6" (30.5 cm/22.9 cm/
15.2 cm) triple element
E. Control panel
F. Ceramic cooking surface
G. 10"/6" (25.4 cm/15.2 cm)
dual element
H. 6" (15.2 cm) single
element
5
COOKTOP CONTROLS – ELECTRONIC TOUCH CONTROLS
Cooktop Controls
The electronic touch controls offer a variety of heat settings
for optimal cooking results.
For maximum element operation, all cooktop electronic touch
controls can be set to High when bringing liquids to a rapid boil.
When the cooktop is turned on or after power is restored to the
cooktop after a power failure, all temperature setting lights will
glow for 10-15 seconds. After the lights go off, the cooktop is
ready to use.
To Use:
1. Touch ON/OFF for the desired element.
2. Touch the + (plus) or - (minus) keypad to select the power
level.
NOTE: Press and hold the + or - keypad for a few seconds to
quickly scroll through the power level. If a power level is not
selected within approximately 10 seconds, the element will
not turn on.
3. To change the power level while cooking, select a power level
with the + or - keypad.
4. When finished cooking, touch ON/OFF for the desired element
to turn off surface cooking area(s) individually or touch OFF to
turn off all surface cooking areas at once.
Use the following chart as a guide when setting heat levels.
Setting Recommended Use
High
20 BOIL
■ Start food cooking.
■ Bring liquid to a boil.
Medium High
17-19
■ Hold a rapid boil.
■ Quickly brown or sear food.
Medium
10-16
■ Maintain a slow boil.
■ Fry or sauté foods.
Medium Low
04-09
■ Cook soups, sauces, and gravies.
■ Stew or steam food.
Low
03 SIMMER
■ Provide lowest simmer/heat setting.
■ Simmer (range of simmer temperatures).
Keep Warm
02 K. WARM
■ Keep cooked foods warm.
Melt
01 MELT
■ Melt chocolate and butter.
Dual/Triple
Elements
■ Home canning
■ Large-diameter cookware
■ Large quantities of food
Hot Surface Indicator Lights
An “H” will appear in the surface cooking area display as long as
any surface cooking area is too hot to touch, even after the
surface cooking area(s) is turned off.
Cooktop On Indicator Light
The cooktop has a cooktop on indicator light. The light will glow
when any of the elements are on.
The element display will show the current power level when that
element is on and a power level is selected.
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
REMEMBER: When cooktop is in use, the entire cooktop
area may become hot.
A. Hot surface indicator
6
Dual/Triple Element
The dual and triple elements offer flexibility depending on the size
of the cookware. Single size can be used in the same way as a
regular element. The dual and triple sizes combine single, dual,
and outer elements and are recommended for larger cookware,
large quantities of food, and home canning.
Triple Element (on some models)
Dual Element
To Use Dual and Triple:
1. When On/Off is touched, all heating zones for the selected
element will be active. To reduce the number of heating zones
being used, touch BURNER SIZE. One, two, or three lights will
glow to indicate the number of burner zones being used. One
of the lights will blink.
2. Touch the + or - keypad to select the power level. A tone will
sound each time a keypad is touched.
NOTE: Press and hold + or - keypad for a few seconds to
quickly scroll through the power level. If a power level is not
selected within approximately 10 seconds, the element will
not turn on.
3. To change the power level while cooking, touch the + or -
keypad to select a new power level.
NOTE: If the power level is at the minimum power setting,
press “-” minus to jump to the maximum setting.
4. To change the heating zones being used while cooking, touch
BURNER SIZE.
5. When finished cooking, touch ON/OFF for the desired element
to turn off the surface cooking area.
Control Lock
The Control Lock cooktop control avoids unintended use of the
surface cooking areas. When the cooktop is locked out, the
surface cooking areas cannot be turned on by the cooktop touch
controls.
To Lock Cooktop: Touch and hold CONTROL LOCK HOLD 3 SEC
for 3 seconds. After 3 seconds, CONTROL LOCK HOLD 3 SEC will
glow red, indicating that the cooktop controls are in the lockout
position.
To Unlock Cooktop: Touch and hold CONTROL LOCK HOLD
3 SEC for 3 seconds.
A. Single size
B. Dual size
C. Triple size
A. Single element
B. Dual element
A. Burner size
7
PARTS AND FEATURES – KNOB CONTROLS
This manual covers different models. The cooktop you have purchased may have some or all of the items listed.
30" (76.2 cm) Control Panel
30" (76.2 cm) Cooktop
36" (91.4 cm) Control Panel
36" (91.4 cm) Cooktop
A. 6" (15.2 cm) single element
control knob
B. 10"/6" (25.4 cm/15.2 cm) dual
element control knob
C. 10" (25.4 cm) single element
control knob
D. 6" (15.2 cm) single element
control knob
E. Three-speed fan control
F. Hot surface indicator light
G. Cooktop on indicator light
A B C D
F
EH GI
A. 6" (15.2 cm) single element
B. Downdraft vent grille
C. 10"/6" (25.4 cm/15.2 cm)
dual element
D. Control panel
E. Cooktop on indicator light
F. Hot surface indicator light
G. 6" (15.2 cm) single element
H. Ceramic cooking surface
I. 10" (25.4 cm) single element
A. 8" (20.3 cm) single element
control knob
B. 6" (15.2 cm) single element
control knob
C. 12"/9"/6" (30.5 cm/22.9 cm/
15.2 cm) triple element
control knob
D. Three-speed fan control
E. 10" (25.4 cm) single element
control knob
F. 6" (15.2 cm) single element
control knob
A. 8" (20.3 cm) single element
B. 6" (15.2 cm) single element
C. Downdraft vent grille
D. 12"/9"/6" (30.5 cm/22.9 cm/
15.2 cm) triple element
E. Control panel
F. Cooktop on indicator light
G. Hot surface indicator light
H. Ceramic cooking surface
I. 10" (25.4 cm) single element
J. 6" (15.2 cm) single element
8
COOKTOP CONTROLS – KNOB CONTROLS
Cooktop Controls
The controls can be set to anywhere between Hi (high) and Lo (low).
To Use:
Push in and turn knob to desired heat setting.
Use the following chart as a guide when setting heat levels.
Setting Recommended Use
Hi
High
■ Bring liquid to a boil.
Med High
Medium High
■ Hold a rapid boil.
■ Quickly brown or sear food.
Med
Medium
■ Maintain a slow boil.
■ Fry or sauté foods.
■ Cook soups, sauces, and gravies.
Med Low
Medium Low
■ Stew or steam food.
■ Simmer.
Lo
Low
■ Keep cooked foods warm.
Dual/Triple
Circuit Elements
■ Home canning
■ Large-diameter cookware
■ Large quantities of food
Melt
■ Melt chocolate or butter.
Hot Surface Indicator Light
This unit features a Hot Surface indicator light. The Hot Surface
indicator light will glow as long as any surface cooking area is too
hot to touch, even after the surface cooking area(s) is turned off.
If the cooktop is on when a power failure occurs, the Hot
Surface indicator light will remain on after the power is restored
to the cooktop. It will remain on until the cooktop has cooled
completely.
Cooktop On Indicator Light
Each cooktop has a Cooktop On Indicator light. When the control
knob is on, the light will glow.
Dual/Triple Circuit Element
The dual-size and triple-size elements offer flexibility depending
on the size of the cookware. Single size can be used in the same
way as a regular element. The dual and triple sizes combine
single, dual, and outer elements and are recommended for larger
cookware, large quantities of food, and home canning.
Triple Element (on some models)
Dual Element
To Use Single:
1. Push in and turn knob from OFF to the Single zone anywhere
between Melt and Hi.
2. Turn knob to OFF when finished.
To Use Dual and Triple:
1. Push in and turn knob from OFF to the Dual
or Triple zone anywhere between Melt and Hi.
2. Turn knob to OFF when finished.
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
REMEMBER: When cooktop is in use, the entire cooktop
area may become hot.
A. Single size
B. Dual size
C. Triple size
A. Single element
B. Dual element
9
COOKTOP USE
Downdraft Ventilation System
NOTE: Electronic touch control model is shown.
The downdraft ventilation system consists of a vent cover, filter,
and vent fan. The downdraft ventilation system removes cooking
vapors, odors, and smoke from foods prepared on the cooktop.
IMPORTANT: For optimal performance, operate the downdraft
ventilation system with the filter properly installed.
To avoid the buildup of grease, the filter should be cleaned often.
For more information on proper filter placement and cleaning, see
“Downdraft Ventilation System” in the “General Cleaning” section.
To Use – Electronic Touch Control:
1. Touch 3 SPEED once for High mode, twice for Medium mode,
or three times for Low mode. A beep will sound each time
3 Speed is touched.
2. When cooking is completed, touch OFF to turn the
downdraft system off, or touch and hold 3 SPEED for
approximately 4 seconds to set the downdraft ventilation
system to Automatic mode. In Automatic mode, the
downdraft ventilation system will shut off automatically
after 10 minutes.
To Use – Knob Control:
Turn vent fan knob to LO, or HI, or to the midpoint for Medium.
Turn vent fan knob to OFF when finished cooking or when the
cooktop is not in use.
Home Canning
When canning for long periods, alternate the use of surface
cooking areas, elements, or surface burners between batches.
This allows time for the most recently used areas to cool.
■ Center the canner on the grate or largest surface cooking area or
element. On electric cooktops, canners should not extend more
than
1
/
2
" (1.3 cm) beyond the surface cooking area or element.
■ Do not place canner on 2 surface cooking areas, elements,
or surface burners at the same time.
■ Use only flat-bottomed canners.
■ For more information, contact your local agricultural
department. Companies that manufacture home canning
products can also offer assistance.
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element, or surface burner.
Ideal cookware should have a flat bottom, straight sides, and a
well-fitting lid and the material should be of medium-to-heavy
thickness.
Rough finishes may scratch the cooktop. Aluminum and copper
may be used as a core or base in cookware. However, when used
as a base, they can leave permanent marks on the cooktop or
grates.
Cookware material is a factor in how quickly and evenly heat is
transferred which affects cooking results. A nonstick finish has
the same characteristics as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
Use the following chart as a guide for cookware material
characteristics.
Cookware Characteristics
Aluminum
■ Heats quickly and evenly.
■ Suitable for all types of cooking
■ Medium or heavy thickness is best
for most cooking tasks.
Cast iron
■ Heats slowly and evenly.
■ Good for browning and frying
■ Maintains heat for slow cooking.
Ceramic or
ceramic glass
■ Follow manufacturer’s instructions.
■ Heats slowly but unevenly.
■ Ideal results on low-to-medium
heat settings
Copper
■ Heats very quickly and evenly.
Earthenware
■ Follow manufacturer’s instructions.
■ Use on low heat settings.
Porcelain
enamel-
on-steel or
cast iron
■ See stainless steel or cast iron.
Stainless steel
■ Heats quickly but unevenly.
■ A core or base of aluminum or copper on
stainless steel provides even heating.
A. Vent grille
B. Removable grease filter
C. Ceramic glass top
10
Ceramic Glass
The surface cooking area will glow red when an element is on.
Some parts of the surface cooking area may not glow red when
an element is on. This is normal operation. The burner will cycle
on and off to maintain the selected heat level. It will also randomly
cycle off and back on again, even while on High, to keep the
cooktop from extreme temperatures.
It is normal for the surface of light-colored ceramic glass to
appear to change color when surface cooking areas are hot.
As the glass cools, it will return to its original color.
Cleaning off the cooktop before and after each use will help
keep it free from stains and provide the most even heating. On
cooktops with light-colored ceramic glass, soils and stains may
be more visible and may require more cleaning and attention.
Cooktop cleaner and a cooktop scraper are recommended.
For more information, see the “General Cleaning” section.
■ Avoid storing jars or cans above the cooktop. Dropping
a heavy or hard object onto the cooktop could crack the
cooktop.
■ To avoid damage to the cooktop, do not leave a hot lid on
the cooktop. As the cooktop cools, air can become trapped
between the lid and the cooktop, and the ceramic glass could
break when the lid is removed.
■ For foods containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly. Then, while wearing oven mitts, remove the spills
using a scraper while the surface is still warm. If sugary spills
are allowed to cool down, they can adhere to the cooktop and
can cause pitting and permanent marks.
■ To avoid scratches, do not slide cookware or bakeware across
the cooktop. Aluminum or copper bottoms and rough finishes
on cookware or bakeware could leave scratches or marks on
the cooktop. Do not cook popcorn in prepackaged aluminum
containers on the cooktop. They could leave aluminum marks
that cannot be removed completely.
■ To avoid damage to the cooktop, do not allow objects that
could melt, such as plastic or aluminum foil, to touch any
part of the entire cooktop.
■ To avoid damage to the cooktop, do not use the cooktop
as a cutting board.
■ Use cookware that is about the same size as the surface
cooking area. Cookware should not extend more than
1
/
2
"
(1.3 cm) outside the area.
■ Use flat-bottomed cookware for best heat conduction and
energy efficiency. Cookware with rounded, warped, ribbed,
or dented bottoms could cause uneven heating and poor
cooking results.
■ Determine flatness by placing the straight edge of a ruler
across the bottom of the cookware. While you rotate the
ruler, no space or light should be visible between it and
the cookware.
■ Cookware designed with slightly indented bottoms or small
expansion channels can be used.
■ Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
■ To avoid damage to the cooktop, do not cook foods directly
on the cooktop.
A
B
C
A. Surface cooking area
B. Cookware/canner
C.
1
/
2
" (1.3 cm) maximum overhang
11
COOKTOP CARE
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are OFF and
the cooktop is cool. Always follow label instructions on cleaning
products.
Soap, water, and a soft cloth or sponge are suggested first unless
otherwise noted.
CERAMIC GLASS (on some models)
To avoid damaging the cooktop, do not use steel wool, abrasive
powder cleansers, chlorine bleach, rust remover, or ammonia.
1. Remove food/residue with the Cooktop Scraper.
■ For best results, use the Cooktop Scraper while the cooktop
is still warm but not hot to the touch. It is recommended to
wear an oven mitt while scraping the warm cooktop.
■ Hold the Cooktop Scraper at approximately a 45° angle
against the glass surface and scrape the residue. It will be
necessary to apply pressure in order to remove the residue.
Allow the cooktop to cool down completely before proceeding
to Step 2.
2. Apply a few dime-sized drops of affresh
®
Cooktop Cleaner to
the affected areas.
■ Rub affresh
®
Cooktop Cleaner onto the cooktop surface
with the blue Cooktop Cleaning Pad. Some pressure is
needed to remove stubborn stains.
■ Allow the cleaner to dry to a white haze before proceeding
to Step 3.
3. Polish with a clean, dry cloth or a clean, dry paper towel.
■ Repeat steps 1 through 3 as necessary for stubborn
or burned-on stains.
The Complete Cooktop Cleaner Kit is available for order and
includes the following:
■ Cooktop Scraper
■ affresh
®
Cooktop Cleaner
■ Blue Cooktop Cleaning Pads
See the “Accessories” section for part numbers and information
about ordering.
STAINLESS STEEL (on some models)
To avoid damage to stainless steel surfaces, do not use soap-
filled scouring pads, abrasive cleaners, cooktop cleaner,
steelwool pads, gritty washcloths, or abrasive paper towels.
For best results, use a soft cloth or non-scratch sponge.
Rub in direction of grain to avoid damaging.
Cleaning Method:
■ affresh
®
Stainless Steel Cleaner Part Number W10355016
(not included):
See the “Assistance or Service” section to order.
■ Liquid detergent or all-purpose cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
■ Vinegar for hard water spots
COOKTOP CONTROLS
To avoid damage to the cooktop controls, do not use steel wool,
abrasive cleansers, or oven cleaner.
To avoid damage, do not soak knobs.
When replacing knobs, make sure knobs are in the Off position.
On some models, do not remove seals under knobs.
Cleaning Method:
■ Soap and water:
Pull knobs straight away from control panel to remove.
■ Do not place knobs in dishwasher.
CONTROL PANEL
To avoid damage to the control panel, do not use abrasive
cleaners, steel-wool pads, gritty washcloths, or abrasive paper
towels.
Cleaning Method:
■ Glass cleaner and soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly
on panel.
■ affresh
®
Kitchen and Appliance Cleaner Part Number
W10355010 (not included):
See the “Assistance or Service” section to order.
12
DOWNDRAFT VENTILATION SYSTEM
Vent Grate
Cleaning Method:
■ Grasp the opening and lift the vent grille of the cooktop.
■ Wipe clean or wash in sink:
Nonabrasive plastic scrubbing pad and mildly abrasive
cleanser.
■ Dishwasher:
Use mild detergent.
Removable Grease Filter
The filter is a permanent type and should be cleaned when soiled.
Cleaning Method:
■ Turn off the downdraft ventilation system before removing
the filter.
■ Remove vent grate then lift the filter out of the vent chamber.
■ Clean the filter in the sink with warm water and detergent
or in the dishwasher.
■ Replace the filter.
The filter should always be placed at an angle. As you face
the front of the cooktop, the top of the filter should rest
against the left side of the vent opening. The bottom of the
filter should rest against the right side of the vent chamber at
the bottom.
If the filter is flat against the fan wall, ventilation effectiveness
will be reduced.
Ventilation Chamber
The ventilation chamber, which houses the filter, should be
cleaned in the event of spills or when it becomes coated with
a film of grease.
Cleaning Method:
■ Mild household detergent or cleanser and paper towel,
damp cloth, or sponge:
Apply detergent or cleanser to paper towel, damp cloth,
or sponge, not directly to the ventilation chamber.
A. Vent grille
B. Removable grease filter
C. Ceramic glass top
13
TROUBLESHOOTING
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,
refer to the warranty page in this manual and scan the code there with your mobile device, or visit https://jennair.custhelp.com.
In Canada, visit http://www.jennair.ca.
Contact us by mail with any questions or concerns at the address below.
In the U.S.A.:
Jenn-Air Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Problem Possible Causes and/or Solutions
Nothing will operate
A household fuse has blown or a circuit breaker has tripped: Replace the fuse or reset
the circuit breaker. If the problem continues, call an electrician.
Cooktop isn’t wired properly: See the Installation Instructions.
Cooktop will not operate
Control knob set incorrectly: Push in knob before turning to a setting.
One or more burners stopped working during use: Allow the cooktop to cool down for 30 minutes,
then turn the burner on again.
Control Lock is not set: Press and hold “Control Lock” for 3 seconds
Excessive heat around
cookware on cooktop
Cookware is not the proper size: Use cookware about the same size as the surface cooking area,
element, or surface burner. Cookware should not extend more than ½" (1.3 cm) outside the cooking area.
Cooktop surfaces become hot: When cooktop is in use, the entire cooktop area may become hot.
Cooktop cooking results
not what expected
Proper cookware is not being used: See the “Cookware” section.
Control knob is not set to the proper heat level: See the “Cooktop Controls” section.
Cooktop is not level: Level the cooktop. See the Installation Instructions.
Certain power levels seem to take longer to cook food or some power levels do not perform as
well as usual: The cooktop regulates the temperature of the internal components and automatically
reduces the power of all the elements in use without any visual or audible feedback. Allow the cooktop
to cool down for 30 minutes to resume normal cooking performance. See “To Use” in the “Cooktop
Controls” section.
Cooktop is beeping
Key is pressed and held: Remove any objects left on the control area, or wipe any debris from the
control panel surface. If the cooktop continues beeping for longer than 15 minutes, the control panel
will lock, and the F1E0 code will appear in the display. See “Cooktop is displaying F1E0 code” in this
section.
Cooktop is displaying
F1E0 code
Cooktop is displaying F1E0, indicating that one or more keys are permanently pressed: Follow
the steps below.
1. Make sure the cooktop controls are off.
2. Clean the cooktop touch control panel thoroughly. See the “General Cleaning” section.
3. Disconnect power or unplug the cooktop.
4. After 1 minute, reconnect power or plug in the cooktop.
5. If error returns after 1 minute, call for service.
In Canada:
Jenn-Air Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
14
ASSISTANCE OR SERVICE
If you need service
Please refer to the warranty page in this manual.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only factory specified parts. These factory specified parts
will fit right and work right because they are made with the same
precision used to build every new Jenn-Air
®
appliance.
To locate factory specified parts in your area, call us or your
nearest Jenn-Air designated service center.
In the U.S.A.
Call the Jenn-Air Customer eXperience Center toll-free:
1-800-JENNAIR (1-800-536-6247) or visit our website at
www.jennair.com.
Our consultants provide assistance with:
■ Scheduling of service. Jenn-Air appliances designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service anywhere in the United States.
■ Features and specifications on our full line of appliances.
■ Referrals to local Jenn-Air appliance dealers.
■ Installation information.
■ Use and maintenance procedures.
■ Accessory and repair parts sales.
■ Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
For further assistance:
If you need further assistance, you can write to Jenn-Air with any
questions or concerns at:
Jenn-Air Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
Call the Jenn-Air Customer eXperience Center toll-free:
1-800-JENNAIR (1-800-536-6247) or visit our website at
www.jennair.ca.
Our consultants provide assistance with:
■ Scheduling of service. Jenn-Air appliances designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service anywhere in Canada.
■ Features and specifications on our full line of appliances.
■ Referrals to local Jenn-Air appliance dealers.
■ Use and maintenance procedures.
■ Accessory and repair parts sales.
For further assistance:
If you need further assistance, you can write to Jenn-Air with any
questions or concerns at:
Customer eXperience Centre
Whirlpool Canada
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
Accessories
To order accessories, visit our website at www.jennair.com.
affresh
®
Stainless Steel Cleaner
(stainless steel models)
Order Part Number W10355016
affresh
®
Kitchen and Appliance Cleaner
Order Part Number W10355010
15
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions
can be addressed without service. Please take a few minutes to review the Troubleshooting or Problem Solver
section of the Use and Care Guide, scan the QR code on the right to access additional resources, or visit
https://jennair.custhelp.com.
2. All warranty service is provided exclusively by our authorized Jenn-Air Service Providers. In the U.S. and Canada,
direct all requests for warranty service to:
Jenn-Air Customer eXperience Center
1-800-JENNAIR (1-800-536-6247).
If outside the 50 United States or Canada, contact your authorized Jenn-Air dealer to determine whether another warranty applies.
JENN-AIR
®
COOKING
LIMITED WARRANTY
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED
TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
Customer eXperience Center:
■ Name, address and telephone number
■ Model number and serial number
■ A clear, detailed description of the problem
■ Proof of purchase including dealer or retailer name and address
FIVE YEAR LIMITED WARRANTY
WHAT IS COVERED WHAT IS NOT COVERED
TWO YEAR LIMITED WARRANTY (PARTS & LABOR)
For two years from the date of purchase, when this major appliance
is installed, operated and maintained according to instructions
attached to or furnished with the product, Jenn-Air brand of
Whirlpool Corporation or Whirlpool Canada, LP (hereafter “Jenn-Air”)
will pay for factory specified replacement parts and repair labor to
correct defects in materials or workmanship that existed when this
major appliance was purchased or, at its sole discretion replace the
product. In the event of product replacement, your appliance will be
warranted for the remaining term of the original unit’s warranty period.
THIRD THROUGH FIFTH YEAR LIMITED WARRANTY
(CERTAIN COMPONENT PARTS ONLY - LABOR NOT INCLUDED)
In the third through fifth years from the date of original purchase,
when this major appliance is installed, operated and maintained
according to instructions attached to or furnished with the product,
Jenn-Air will pay for factory specified parts for the following
components to correct non-cosmetic defects in materials or
workmanship in these parts that prevent function of this major
appliance and that existed when this major appliance was
purchased. This is a limited 5-year warranty on the below named
parts only and does not include repair labor.
■ Electric element
■ Touch Pad and microprocessor
■ Glass ceramic cooktop: if due to thermal breakage
■ Electronic controls
■ Magnetron tube
■ Sealed gas burners
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
Service must be provided by a Jenn-Air designated service company.
This limited warranty is valid only in the United States or Canada
and applies only when the major appliance is used in the country in
which it was purchased. This limited warranty is effective from the
date of original consumer purchase. Proof of original purchase date is
required to obtain service under this limited warranty.
1. Commercial, non-residential, multiple-family use, or use inconsistent
with published user, operator or installation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or installation,
installation not in accordance with electrical or plumbing codes or
correction of household electrical or plumbing (i.e. house wiring, fuses
or water inlet hoses).
4. Consumable parts (i.e. light bulbs, batteries, air or water filters,
preservation solutions, etc.).
5. Defects or damage caused by the use of non-genuine Jenn-Air parts
or accessories.
6. Conversion of products from natural gas or L.P. gas.
7. Damage from accident, misuse, abuse, fire, floods, acts of God or
use with products not approved by Jenn-Air.
8. Repairs to parts or systems to correct product damage or defects
caused by unauthorized service, alteration or modification of
the appliance.
9. Cosmetic damage including scratches, dents, chips, and other damage
to the appliance finishes unless such damage results from defects in
materials and workmanship and is reported to Jenn-Air within 30 days.
10. Discoloration, rust or oxidation of surfaces resulting from caustic
or corrosive environments including but not limited to high salt
concentrations, high moisture or humidity or exposure to chemicals.
11. Food or medicine loss due to product failure.
12. Pick-up or delivery. This product is intended for in-home repair.
13. Travel or transportation expenses for service in remote locations where
an authorized Jenn-Air servicer is not available.
14. Removal or reinstallation of inaccessible appliances or built-in fixtures
(i.e. trim, decorative panels, flooring, cabinetry, islands, countertops,
drywall, etc.) that interfere with servicing, removal or replacement of
the product.
15. Service or parts for appliances with original model/serial numbers
removed, altered or not easily determined.
The cost of repair or replacement under these excluded circumstances
shall be borne by the customer.
https://jennair.custhelp.com
12/14
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow
limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific
legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations
contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you
should ask Jenn-Air or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-AIR
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of
incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you
also may have other rights that vary from state to state or province to province.
16
Notes
17
SÉCURITÉ DE LA TABLE DE CUISSON
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :
Avertissements de la proposition 65 de l'État de Californie :
AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de
cancers.
AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de
malformations et autres déficiences de naissance.
18
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
CONSERVEZ CES INSTRUCTIONS
AVERTISSEMENT :
Pour réduire le risque d'incendie, de
choc électrique, de blessures ou de dommages lors de
l'utilisation de la table de cuisson, observer les précautions
élémentaires suivantes, y compris ce qui suit :
■ MISE EN GARDE :
Ne pas remiser dans les armoires
au-dessus d'une table de cuisson, des articles que des
enfants pourraient vouloir atteindre. Les enfants pourraient
se brûler ou se blesser en grimpant sur la table de cuisson.
■ Installation appropriée – S’assurer que la table de cuisson
est correctement installée et reliée à la terre par un
technicien qualifié.
■ Ne jamais utiliser la table de cuisson pour réchauffer ou
chauffer la pièce.
■
Ne pas laisser les enfants seuls – Les enfants ne doivent
pas être laissés seuls ou sans surveillance dans la pièce
où la table de cuisson est en service. Ne jamais laisser les
enfants s’asseoir ou se tenir sur une partie quelconque de
la table de cuisson.
■ Porter des vêtements appropriés – Des vêtements amples
ou détachés ne doivent jamais être portés pendant
l’utilisation de la table de cuisson.
■ Entretien par l’utilisateur – Ne pas réparer ou remplacer
toute pièce de la table de cuisson si ce n’est pas
spécifiquement recommandé dans le manuel. Toute autre
opération d’entretien ou de réparation doit être confiée à un
technicien qualifié.
■ Remisage sur la table de cuisson – Des matériaux
inflammables ne doivent pas être remisés près des
éléments à la surface.
■ Ne pas utiliser d’eau sur un feu de graisse – Étouffer le feu
ou la flamme ou utiliser un extincteur à produits chimiques
secs ou à mousse.
■ N’utiliser que des mitaines de four sèches – Des mitaines
de four mouillées ou humides sur des surfaces chaudes
peuvent provoquer des brûlures provenant de la vapeur.
Ne pas laisser les mitaines de four toucher les éléments
chauffants. Ne pas utiliser une serviette ou autre tissu
épais.
■ NE PAS TOUCHER LES ÉLÉMENTS À LA SURFACE OU
L’ESPACE PRÈS DES ÉLÉMENTS – Les éléments de
surface peuvent être chauds même lorsqu’ils ont une teinte
foncée. Les endroits près des éléments à la surface
peuvent devenir assez chauds pour provoquer des
brûlures. Pendant et après l’utilisation, ne pas toucher les
éléments chauffants et ne pas laisser les vêtements ou
autres matériaux inflammables entrer en contact avec ces
éléments de surface ou les endroits près des éléments,
avant qu’ils soient suffisamment refroidis. Ces endroits
comprennent la table de cuisson et les surfaces près de la
table de la cuisson.
■ Utiliser des ustensiles de format approprié – La table de
cuisson est munie d’un ou de plusieurs éléments
chauffants de différentes grandeurs. Choisir les ustensiles
qui ont un fond plat assez grand pour couvrir l’élément
chauffant de la surface de cuisson. L’utilisation d’ustensiles
trop petits exposera une partie de l’élément chauffant, ce
qui peut provoquer l’inflammation des vêtements.
L’utilisation d’un récipient de format correct améliore
l’efficacité de la cuisson.
■ Ne jamais laisser les éléments de la table de cuisson sans
surveillance alors qu’ils chauffent à la puissance maximale
– Il pourrait en résulter une ébullition qui cause de la
fumée et des renversements de corps gras qui peuvent
s’enflammer.
■ Ustensiles de cuisson vitrifiés – Seulement certains types
d’ustensiles de verre, vitrocéramique, céramique, faïence
ou autres surfaces vitrifiées conviennent pour le service
sur une table de cuisson, sans bris attribuables aux
changements soudains de température.
■ Les poignées des ustensiles doivent être tournées vers
l’intérieur et non vers le dessus des éléments adjacents –
Pour réduire les risques de brûlures, d’inflammation de
produits combustibles et de renversements dus à
l’entrechoquement non intentionnel des ustensiles, la
poignée d’un ustensile doit être positionnée de sorte qu’elle
est tournée vers l’intérieur et non au-dessus des éléments
de surface adjacents.
■
Ne pas faire cuire sur une table de cuisson endommagée –
Si la table de cuisson est brisée, les solutions de
nettoyage et les renversements peuvent pénétrer dans la
table brisée et créer le risque d’un choc électrique.
Contacter immédiatement un technicien qualifié.
■ Nettoyer la table de cuisson avec prudence – Si une
éponge ou un chiffon mouillé est utilisé pour essuyer les
renversements sur une surface de cuisson chaude, éviter
les brûlures causées par la vapeur chaude. Certains
nettoyants peuvent produire des émanations désagréables
lorsqu’ils sont utilisés sur une surface chaude.
Pour les appareils avec hotte de ventilation –
■ Nettoyer les hottes de ventilation fréquemment – La
graisse ne doit pas s’accumuler sur la hotte ou le filtre.
■
Lorsque vous flambez des aliments sous la hotte, mettre le
ventilateur en marche.
Pour les appareils à éléments en spirale –
■ S’assurer que les cuvettes de propreté sont en place –
L’absence de ces cuvettes au cours de la cuisson peut
causer des dommages aux fils ou aux composants en
dessous des éléments.
■
Garnissages protecteurs – Ne pas recouvrir les cuvettes
de papier d’aluminium sauf tel que suggéré dans le
manuel. L’installation incorrecte de papier d’aluminium ou
autre matériau peut causer un risque de choc électrique ou
d’incendie.
■ Ne pas tremper les éléments de chauffage amovibles –
Les éléments de chauffage ne doivent jamais être
immergés dans l'eau.
19
PIÈCES ET CARACTÉRISTIQUES –
COMMANDES ÉLECTRONIQUES TACTILES
Ce manuel couvre différents modèles. La table de cuisson que vous avez achetée peut comporter tous les articles énumérés
ou seulement certains d'entre eux.
Tableau de commande de 30" (76,2 cm)
Table de cuisson de 30" (76,2 cm)
Tableau de commande de 36" (91,4 cm)
Table de cuisson de 36" (91,4 cm)
A. Commande électronique tactile d'élément simple
de 6" (15,2 cm)
B. Commande électronique tactile d'élément double
de 10"/6" (25,4 cm/15,2 cm)
C. Commandes verrouillées appuyer pendant 3 sec.
D. Commande électronique tactile du ventilateur
à 3 vitesses
E. Commande électronique tactile d'élément simple
de 6" (15,2 cm)
F. Commande électronique tactile d'élément double
de 9"/6" (22,9 cm/15,2 cm)
A. Élément simple de 6" (15,2 cm)
B. Grille de ventilation à extraction
par le bas
C. Élément double de 9"/6"
(22,9 cm/15,2 cm)
D. Tableau de commande
E. Élément simple de 6" (15,2 cm)
F. Surface de cuisson
en céramique
G. Élément double de 10"/6"
(25,4 cm/15,2 cm)
A. Commande électronique
tactile d'élément simple de 8"
(20,3 cm)
B. Commande électronique
tactile d'élément simple de 6"
(15,2 cm)
C. Commande électronique
tactile d'élément simple de 6"
(15,2 cm)
D. Commande électronique tactile
d'élément double de 10"/6"
(25,4 cm/15,2 cm)
E. Commandes verrouillées
appuyer pendant 3 sec.
F. Commande électronique tactile
du ventilateur à 3 vitesses
G. Commande électronique tactile
d'élément triple de 12"/9"/6"
(30,5 cm/22,9 cm/15,2 cm)
A. Élément simple de 8" (20,3 cm)
B. Élément simple de 6" (15,2 cm)
C. Grille de ventilation à extraction
par le bas
D. Élément triple de 12"/9"/6"
(30,5 cm/22,9 cm/15,2 cm)
E. Tableau de commande
F. Surface de cuisson en
céramique
G. Élément double de 10"/6"
(25,4 cm/15,2 cm)
H. Élément simple de 6" (15,2 cm)
20
COMMANDES DE LA TABLE DE CUISSON –
COMMANDES ÉLECTRONIQUES TACTILES
Commandes de la table de cuisson
Les commandes électroniques tactiles offrent une grande variété
de réglages de chaleur pour des résultats de cuisson optimaux.
Pour un fonctionnement maximal de l’élément, toutes les
commandes électroniques tactiles de la table de cuisson peuvent
être réglées à High (élevé) lorsqu’on porte rapidement un liquide à
ébullition.
Lorsque la table de cuisson est allumée ou une fois le courant
rétabli après une panne de courant, tous les témoins lumineux
de réglage de température s'allument pendant 10 à 15 secondes.
Une fois les témoins lumineux éteints, la table de cuisson est
prête à l'emploi.
Utilisation :
1. Appuyer sur ON/OFF (marche/arrêt) correspondant
à l'élément souhaité.
2. Appuyer sur la touche + (plus) ou - (moins) pour sélectionner
le niveau de puissance.
REMARQUE : Maintenir enfoncée + ou - pendant quelques
secondes pour naviguer rapidement dans les niveaux de
puissance. Si un niveau de puissance n’est pas sélectionné
dans les 10 secondes qui suivent, l’élément ne se met pas en
marche.
3. Pour modifier la puissance pendant la cuisson, sélectionner
un niveau de puissance en utilisant + ou -.
4. À la fin de la cuisson, appuyer sur ON/OFF (marche/arrêt)
pour éteindre la surface de cuisson désirée ou appuyer
sur OFF (arrêt) pour éteindre simultanément toutes les zones
de cuisson.
Utiliser le tableau suivant comme guide lors du réglage des
niveaux de chaleur.
Réglage Utilisation recommandée
Élevé
20 BOIL
(ébullition)
■ Démarrer la cuisson des aliments.
■ Porter un liquide à ébullition.
Moyen-élevé
17-19
■ Maintenir une ébullition rapide.
■ Brunir ou saisir rapidement les aliments.
Moyenne
10-16
■ Maintenir une ébullition lente.
■ Faire frire ou sauter les aliments.
Moyen - bas
04-09
■ Faire cuire les soupes et les sauces.
■ Faire mijoter ou étuver les aliments.
Bas
03 SIMMER
(mijoter)
■ Fournit le réglage le plus bas
de mijotage/chaleur.
■ Mijotage (gamme de températures de
mijotage).
Maintien
au chaud
02 K. WARM
(maintien
au chaud)
■ Pour garder au chaud les aliments cuits.
Faire fondre
01 MELT
(faire fondre)
■ Faire fondre le chocolat et le beurre.
Éléments
double/triple
■ Préparation de conserves à la maison
■ Ustensile de cuisson à grand diamètre
■ Grandes quantités de nourriture
Témoins lumineux de surface chaude
Un “H” apparaît sur l’affichage de la surface de cuisson tant
qu’une surface de cuisson est trop chaude pour être touchée,
même une fois que la ou les surfaces sont éteintes.
Témoin lumineux d’allumage de la table de cuisson
La table de cuisson est munie d’un témoin lumineux d’allumage
de la table de cuisson. Le témoin s’illumine lorsqu’un élément est
en marche.
L’affichage de l’élément indique le niveau de puissance utilisé
lorsque l’élément est en marche et qu’une puissance est
sélectionnée.
Risque d’incendie
La flamme d'un brûleur ne devrait pas dépasser le bord
du récipient de cuisson.
Fermer tous les réglages lorsque la cuisson est
terminée.
Le non-respect de ces instructions peut causer un
décès ou un incendie.
AVERTISSEMENT
N’OUBLIEZ PAS : Quand l’appareil est utilisé, toute la
surface de la table de cuisson peut devenir chaude.
A. Témoin de surface chaude
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
JennAir JED3536GS Le manuel du propriétaire
- Catégorie
- Cuisinières
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: JennAir JED3536GS Owner's manual
Documents connexes
Autres documents
-
KitchenAid KECC667BBL Manuel utilisateur
-
Jenn-Air 36" (91.4 cm) Manuel utilisateur
-
-
Jenn-Air JED4430WS01 Le manuel du propriétaire
-
KitchenAid KCED600GSS Le manuel du propriétaire
-
-
-
-
Whirlpool WCE97US0HB Manuel utilisateur
-
Fox Run 10100 Manuel utilisateur
