D M 3 5 D A C M O D U L E
User Guide
DM35 DAC Module User Guide2
CAUTION
TO REDUCE THE RISK OF FIRE, REPLACE WITH THE
SAME TYPE AND RATING OF FUSE.
ATTENTION
UTILISER UN FUSIBLE DE RECHANGE MÊME TYPE.
Safety compliance
This product has been designed to meet the IEC 60065
international electrical safety standard.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
The lightning flash with an arrowhead symbol within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated 'dangerous voltage' within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
CAUTION: To reduce the risk of electrical shock do not
remove cover (or back). No user serviceable parts inside.
Refer servicing to qualified service personnel.
WARNING: To reduce the risk of fire or electrical shock,
do not expose this apparatus to rain or moisture.
CAUTION: In Canada and the USA, to prevent electric
shock, match the wide blade of the plug to the wide slot
in the socket and insert the plug fully into the socket.
This product is designed and manufactured to meet strict
quality and safety standards. However, you should be aware
of the following installation and operation precautions.
1. Take heed of warnings & instructions
You should read all the safety and operating instructions
before operating this appliance. Retain this handbook
for future reference and adhere to all warnings in the
handbook or on the appliance.
2. Water and moisture
The presence of electricity near water can be dangerous.
Do not use the appliance near water – for example next to
a bathtub, washbowl, kitchen sink, in a wet basement or
near a swimming pool, etc.
3. Object or liquid entry
Take care that objects do not fall and liquids are not spilled
into the enclosure through any openings. Liquid-filled objects
such as vases should not be placed on the equipment.
4. Ventilation
Do not place the equipment on a bed, sofa, rug or similar
soft surface, or in an enclosed bookcase or cabinet, since
ventilation may be impeded. We recommend a minimum
distance of 50mm around the sides and top of the
appliance to provide adequate ventilation.
5. Heat
Locate the appliance away from naked flames or heat
producing equipment such as radiators, stoves or other
appliances (including other amplifiers) that produce heat.
6. Climate
The appliance has been designed for use in moderate
climates.
7. Racks and stands
Only use a rack or stand that is recommended for use with
audio equipment. If the equipment is on a portable rack it
should be moved with great care, to avoid overturning the
combination.
8. Cleaning
Unplug the unit from the mains supply before cleaning.
The case should normally only require a wipe with a soft,
damp, lint-free cloth. Do not use paint thinners or other
chemical solvents for cleaning.
We do not advise the use of furniture cleaning sprays or
polishes as they can cause indelible white marks if the unit
is subsequently wiped with a damp cloth.
9. Power sources
This appliance must be connected to a mains socket
outlet using the supplied power cord. To disconnect
this apparatus from power, you must disconnect the
power cord. Make sure the power cord is always easily
accessible.
Only connect the appliance to a power supply of the type
described in the operating instructions or as marked on
the appliance.
This is a Class 1 device and must be earthed.
The power switch is a single-pole switch. When the switch
is in the “Off” position, the appliance is not completely
disconnected from the main power.
10. Power-cord protection
Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords and
plugs, and the point where they exit from the appliance.
11. Grounding
Ensure that the grounding means of the appliance is not
defeated.
12. Power lines
Locate any outdoor antenna/aerial away from power lines.
13. Non-use periods
If the unit has a stand-by function, a small amount of
current will continue to flow into the equipment in this
mode. Unplug the power cord of the appliance from the
outlet if left unused for a long period of time.
14. Abnormal smell
If an abnormal smell or smoke is detected from the
appliance, turn the power off immediately and unplug the
unit from the wall outlet. Contact your dealer immediately.
15. Servicing
You should not attempt to service the appliance beyond
that described in this handbook. All other servicing should
be referred to qualified service personnel.
16. Damage requiring service
The appliance should be serviced by qualified service
personnel when:
A. the power-supply cord or the plug has been damaged, or
B. objects have fallen, or liquid has spilled into the
appliance, or
C. the appliance has been exposed to rain, or
D. the appliance does not appear to operate normally or
exhibits a marked change in performance, or
E. the appliance has been dropped or the enclosure
damaged.
DM35 DAC Module User Guide 3
2.4G and 5G FCC Statements
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Cet appareil est conforme à la section 15 des
réglementations de la FCC. Le fonctionnement de
l’appareil est sujetaux deux conditions suivantes :
1. cet appareil ne doit pas provoquer d’interférences
néfastes, et
2. cet appareil doit tolérer les interférences reçues,
y compris celles qui risquent de provoquer un
fonctionnement indésirable.
Note: This product has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This product generates, uses, and
can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Please take attention that changes or modification
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
This equipment should be installed and operated with a
minimum distance 20cm between the radiator and your
body .
Cet équipement doit être installé et utilisé à une distance
minimale de 20 cm entre le radiateur et votre corps.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radioexempts de
licence. L’exploitation est autorisée aux deux conditions
suivantes :
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada,
le présent émetteur radio peut fonctionner avec une
antenne d’un type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique
à l’intention des autres utilisateurs, il faut choisir le type
d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité
nécessaire à l’établissement d’une communication
satisfaisante.
The CE symbol indicates that this Primare product
complies with the EMC (Electromagnetic Compatibility)
and LVD (Low Voltage Directive) standards of the
European Community.
The WEEE symbol indicates this Primare product complies
with the European Parliament and Council Directive
2002/96/EC concerning Waste Electrical and Electronic
Equipment (WEEE). This product must be appropriately
recycled or processed in accordance with these directives.
Consult your local waste disposal authority for guidance.
The RoHS symbol indicates that Primare products are
designed and manufactured to comply with the Restriction
of Hazardous Substances (RoHS) as stated in the European
Parliament and Council Directive 2002/95/EC.
Copyright and acknowledgments
Copyright © 2017-18 Primare AB.
All rights reserved.
Primare AB
Limstensgatan 7
21616 Limhamn
Sweden
http://www.primare.net
Issue: DM35/1
The information in this guide is believed to be correct as
of the date of publication. However, our policy is one of
continuous development and so the information is subject
to change without notice, and does not represent a
commitment on the part of Primare AB.
Primare is a trademark of Primare AB.
This guide was produced by
Human-Computer Interface Ltd.
http://www.interface.co.uk
DM35 DAC Module User Guide4
DM35 DAC Module User Guide 5
CONTENTS
Getting started 6
Congratulations on selecting the DM35 DAC Module 6
Back-panel connections 6
Using the settings menus 6
AUDIO SETTINGS 6
STANDBY SETTINGS 6
Connecting digital sources 7
Technical specification 8
Digital inputs 8
Digital output 8
Index 9
DM35 DAC Module User Guide
6
GETTING STARTED
Congratulations on selecting the DM35
DAC Module
This user guide describes the additional features available
from the DM35 and explains how to set it up so you
can enjoy superb sound reproduction from your digital
sources.
For additional support and assistance please contact your
local authorized Primare dealer, or visit our website at
www.primare.net.
Back-panel connections
The following diagram explains the function of each of the
connectors on the back panel:
Optical
digital inputs
Coax
digital inputs
Digital
output
USB-B
input
Digital inputs
The DM35 adds seven inputs. Initially these are labelled
as shown in the following table, but you can give them
your own aliases to suit the sources in your system.
Label Description
D6–D9 Digital optical on TOS connectors.
D10, D11 Digital coax on RCA connectors.
PC/MAC (12) Digital on USB-B connector.
Connect digital optical sources to the digital optical
inputs D6 to D9 using optical cables.
Connect digital coax sources to the digital coax inputs
D10 and D11 using digital RCA cables.
Digital output
The DM35 provides a coax digital output on an RCA
connector.
l
l
Using the settings menus
The DM35 adds the following menus to the settings
menus.
AUDIO SETTINGS
The DM35 adds a DIGITAL OUTPUT option to the AUDIO
SETTINGS menu:
AUDIO SETTINGS 20
MAXIMUM VOLUME 99
MUTE VOLUME 0
DIGITAL OUTPUT 48kHz
DIGITAL OUTPUT
Allows you to choose the sample rate for analogue inputs
on the digital output as 96kHz (default) or 48kHz. For
digital inputs the output format is the same as the input.
STANDBY SETTINGS
The DM35 adds a STANDBY MODE option to the
STANDBY SETTINGS submenu on the GENERAL SETTINGS
menu:
STANDBY SETTINGS 20
STANDBY MODE NORMAL
AUTO STANDBY AFTER 20MIN
STANDBY MODE can be set to ECO to reduce the standby
consumption to less than 0.5W, but only allows the
product to wake from the analogue and digital inputs,
or NORMAL which also allows the product to wake from
streaming and the PC/MAC input.
DM35 DAC Module User Guide
7
Digital optical source
USB-A to USB-B cable
Digital optical cable
Digital coax source
Digital coax cable
PC/Mac
CONNECTING DIGITAL SOURCES
These methods of playing music from the DM35 involve
connecting the source to the DM35 via a cable, and don’t
require Wi-Fi, Ethernet, or Bluetooth.
To play music from a digital source
Connect the source via a suitable cable:
Digital optical source Digital optical cable
Digital source Digital coax cable
Select the source from the front panel, or using the
remote control.
If you have a phone or tablet on the same Wi-Fi network
as the product you can also use the Prisma app to select
and control sources.
l
l
To use the DM35 as a PC/Mac sound output device
Connect the Mac or PC to the I35 via a USB-A to
USB-B cable.
PC
Windows 7, 8, 8.1, or 10 (32/64-bit) is required. You
need to install the Primare xmos audio driver, available on
primare.net.
Macintosh
OSX 10.4 or later is recommended. No driver is required.
Connect the computer’s USB port to the USB B input on
the I35 using a USB A to USB B cable.
The DM35 will then appear as a sound output device
called DM35 in the Sound control panel (PC) or Sound
system preferences panel (Macintosh).
Select the PC/MAC source on the I35.
Select the DM35 as the sound output device in the
Mac Sound system preferences panel or the PC Sound
control panel.
l
l
l
l
DM35 DAC Module User Guide
8
Digital inputs
4 x Optical/TOSLINK 192kHz/24 bit
2 x RCA 192kHz/24 bit
1 x USB-A up to 192kHz/24 bit; up to DSD128
(5.6MHz)
1 x USB-B up to 768kHz/32 bit; up to DSD256
(11.2MHz)
Digital output
1 x RCA
Analogue input = selectable between 48 or 96kHz
Digital input = native output
TECHNICAL SPECIFICATION
DM35 DAC Module User Guide
9
INDEX
A
Analog inputs and outputs 6
Audio settings menu 6
B
Back panel 6
Balanced inputs 6
C
Coax inputs 6
D
Digital inputs and output 6
Digital output (settings menus) 6
G
General settings menu 6
I
IR input 6
M
Menus
Audio settings 6
General settings 6
O
Optical inputs 6
P
PC/Mac sound output device 7
R
RS232 input 6
S
Settings menus 6
Sources
Connecting 7
T
Technical specification 8
Trigger outputs 6
U
Unbalanced inputs and outputs 6
USB flash drive, playing music from 6
L I M S T E N S G ATA N 7 ,
2 1 6 1 6 L I M H A M N , S W E D E N
More information at primare.net
T H E S O U N D A N D V I S I O N O F S C A N D I N AV I A S I N C E 1 9 8 6
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Primare PRE35 Mode d'emploi
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
- English: Primare PRE35 User guide
Documents connexes
Autres documents
-
VINCENT DAC-7 Le manuel du propriétaire
-
ADVANCE X-I105 Le manuel du propriétaire
-
-
Esoteric N-05 Le manuel du propriétaire
-
TEAC NT-505 Manuel utilisateur
-
Focal Arche Manuel utilisateur
-
TEAC NT-503 Le manuel du propriétaire
-
-