TEAC NT-505 Manuel utilisateur

D01323020C

Z

NT-505

USB DAC/ Network Player

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

For information about this unit’s network functions,

see the TEAC HR Streamer User’s Manual.

The Owner’s Manual and TEAC HR Streamer User’s

Manual can be downloaded from the TEAC Global

Site (http://www.teac-global.com/).

To use network functions and USB flash drive play-

back, you must also use a tablet or smartphone that

has the TEAC HR Streamer app (free) installed and is

connected to the same network as the unit.

ENGLISH

FRANÇAIS

ESPAÑOL

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete

outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the manufac-

turer, or sold with the apparatus. When a

cart is used, use caution when moving the

cart/apparatus combination to avoid injury

from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume)

from earphones or headphones can cause hearing loss.

EN

3

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batter-

ies: there is danger of explosion if a battery is replaced with

an incorrect type of battery. Replace only with the same or

equivalent type.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

V

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and

negative (^) orientations.

o Use batteries of the same type. Never use different types of bat-

teries together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batter-

ies together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The

batteries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

For European Customers

Disposal of electrical and electronic equipment

and batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/

accumulators should be disposed of separately from the

municipal waste stream via collection facilities designated by

the government or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valuable

resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those

elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

The nameplate is located on the bottom of the unit as shown below.

Front side

Nameplate

4

Wireless equipment precautions

Compliance of radio transmitter and

interference

Model for USA

Declaration of Conformity

Responsible party: TEAC AMERICA, INC.

Address: 1834 Gage Road, Montebello, California, U.S.A.

Telephone number : 1-323-726-0303

This device complies with Part.15 of FCC Rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Labeling of authorization

FCC ID: XEG-NT505

Model for Canada

Compliance of radio transmitter

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions:

1) This device may not cause interference; and

2) This device must accept any interference, including interference

that may cause undesired operation of the device.

Labeling of authorization

IC: 1559C-NT505

Compliance of interference

This Class B digital apparatus complies with Canadian ICES-003.

This equipment complies with FCC/IC radiation exposure limits set

forth for an uncontrolled environment and meets the FCC radio

frequency (RF) Exposure Guidelines and RSS-102 of the IC radio

frequency (RF) Exposure rules. This equipment has very low levels

of RF energy that it deemed to comply without maximum permis-

sive exposure evaluation (MPE). But it is desirable that it should be

installed and operated keeping the radiator at least 20cm or more

away from person’s body (excluding extremities: hands, wrists, feet

and ankles).

Model for EEA (European Economic Area)

This product has the function of broadband transmitter using

2.4GHz Band.

Use frequency range: 2400MHz – 2480MHz

Maximum output power: Bluetooth® Class 2 (less than 2.5 mW)

Hereby, TEAC Corporation declares that the radio

equipment type is in compliance with Directive

2014/53/EU., and the other Directives, and

Commission Regulations.

The full text of the EU declaration of conformity is available at the

following internet address. Please contact us by e-mail.

http://www.teac-audio.eu/en/

TEAC Corporation

1-47 Ochiai, Tama-shi, Tokyo, 206-8530, Japan

CAUTION

Authorization of wireless devices are different in countries or regions.

Please use only in the country where you purchased the product.

o Depending on the country, restrictions on the use of Bluetooth

wireless technology might exist.

Confirm the laws and regulations of the country or region where

you want to use the unit before use.

Radiation Exposure requirements

This equipment meets the regulation, which is recognized interna-

tionally, for the case of human exposure to radio waves generated

by the transmitter.

Statement of compliance

Model for USA

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment and meets the FCC radio fre-

quency Exposure Guidelines.

Model for Canada

This equipment complies with IC RSS-102 radiation exposure limits set

forth for an uncontrolled environment.

Model for EEA (European Economic Area)

This equipment complies with EN.62311; Assessment of electronic and

electrical equipment related to human exposure restrictions for elec-

tromagnetic fields; the harmonised standard of DIRECTIVE 2014/53/EU.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Information for interference

(FCC requirements)

This equipment has been tested and found to comply with the lim-

its for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference

by one or more of the following measures.

o Reorient or relocate the equipment and/or the receiving

antenna.

o Increase the separation between the equipment and receiver.

o Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

o Consult the dealer or an experienced radio/TV technician for

help.

EN

5

Contents

Thank you for choosing TEAC.

Read this manual carefully to get the best performance from this

unit. After reading it, keep it in a safe place for future reference.

ATTENTION

o For information about this unit’s network functions, see the TEAC

HR Streamer User’s Manual.

o The Owner’s Manual and TEAC HR Streamer User’s Manual can be

downloaded from the TEAC Global Site (http://www.teac-global.

com/).

o To use network functions and USB flash drive playback, you must

also use a tablet or smartphone that has the TEAC HR Streamer

app (free) installed and is connected to the same network as the

unit.

IMPORTANT SAFETY INSTRUCTIONS ...............................2

Wireless equipment precautions ...................................4

Trademarks and copyrights ........................................5

Included accessories ............................................... 6

Before use .........................................................6

Maintenance ......................................................6

Using the TEAC Global Site .........................................6

Product registration ...............................................6

Downloading the remote app .....................................6

Network connections .............................................. 7

Connections (rear panel) ...........................................8

Connections (front panel) .........................................10

Connecting headphones .........................................11

Using the remote control .........................................11

Names and functions of parts (main unit) .........................12

Upconversion ....................................................13

Names and functions of parts (remote control) ....................14

Display ...........................................................15

Basic operation ...................................................17

Bluetooth® wireless technology ...................................18

Settings ..........................................................21

Playing back music on a computer ................................25

MQA (Master Quality Authenticated) ..............................27

Troubleshooting ..................................................27

Specifications ....................................................29

Trademarks and copyrights

The MQA logo is a trade mark of MQA Limited.

“DSD” is a registered trademark.

The Bluetooth® word mark and logos are registered trademarks

owned by Bluetooth SIG, Inc. and any use of such marks by TEAC

CORPORATION is under license.

Qualcomm aptX is a product of Qualcomm Technologies International,

Ltd.

Qualcomm is a trademark of Qualcomm Incorporated, registered in

the United States and other countries, used with permission. aptX is

a trademark of Qualcomm Technologies International, Ltd., registered

in the United States and other countries, used with permission.

Microsoft and Windows are either registered trademarks or trade-

marks of Microsoft Corporation in the United States and/or other

countries.

Apple, Mac, OS X, macOS, iPad, iPhone and iPod touch are trademarks

of Apple Inc., registered in the U.S. and other countries.

App Store is a service mark of Apple Inc.

Android is a trademark of Google Inc.

LDAC™ and LDAC logo are trademarks of Sony Corporation.

Bulk Pet is a registered trademark of INTERFACE CO., LTD.

Other company names, product names and logos in this document

are the trademarks or registered trademarks of their respective

owners.

Information about copyrights and licensing related to open-source

software is provided in the separate “Important Notice Regarding

Software” document.

6

Using the TEAC Global Site

Check to be sure the box contains all the included items shown

below.

Please contact the store where you purchased this unit if any of these

items are missing or have been damaged during transportation.

Power cord × 1

RCA conversion (RCA to mini plug) cable × 1

Remote control (RC-1330) × 1

Batteries for remote control (AAA) × 2

Owner’s manual (this document, including warranty) × 1

o For information about the warranty, users living in the USA and

Canada should see pages 86–87 and the back cover (war-

ranty document). Users living in Europe and other regions should

see page87.

o The TEAC HR Streamer User’s Manual can be downloaded from

the TEAC Global Site (http://www.teac-global.com/).

Before use

V

Placement precautions

o Do not install this unit in a location that could become hot.

This includes places that are exposed to direct sunlight or near

a radiator, heater, stove or other heating equipment. Moreover,

do not place it on top of an amplifier or other equipment that

generates heat. Doing so could cause discoloration, deformation

or malfunction.

o Avoid locations that are extremely cold or exposed to excessive

humidity or dust.

o When installing this unit, leave a little space (at least 3 cm or 1")

between it and walls and other devices in order to allow good

heat dissipation. If you put it in a rack, for example, leave at least

5 cm (2") open above it and at least 10 cm (4") open behind it.

Failure to provide these gaps could cause heat to build up inside

and result in fire.

o The voltage supplied to the unit should match the voltage

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

o Do not move the unit during use.

o Do not open the body of the unit because this could result in

damage to the circuitry or cause electric shock. If a foreign object

should enter the unit, contact your dealer.

o When removing the power plug from the wall outlet, always pull

directly on the plug; never yank on the cord.

Maintenance

Wipe dirt from the top cover and other panel surfaces using a soft

cloth that has been slightly dampened with a diluted neutral cleanser.

Do not wipe with chemical cleaning cloths, thinner or other chemi-

cal agents. Doing so could damage the surface.

V

For your safety, disconnect the power cord from

the outlet before cleaning.

Included accessories

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

1) Open the TEAC Global Site.

2) In the TEAC Downloads section, click the desired language to

open the Downloads website page for that language.

NOTE

If the desired language does not appear, click Other Languages.

3) Click the “Search by Model Name” section to open the Downloads

page for that product. (Users in Europe should click the product

name in the “Products” section instead.)

4) Select and download the updates that are needed.

Product registration

Customers in the USA, please visit the following TEAC website to

register your TEAC product online.

http://audio.teac.com/support/registration/

Downloading the remote app

To use the network functions and USB flash drive playback functions

of this unit, you must also use a smartphone or tablet that has the

TEAC HR Streamer app (free) installed and is connected to the same

network as the unit.

o For details, see the TEAC HR Streamer User’s Manual.

The TEAC HR Streamer User’s Manual can be downloaded from

the TEAC Global Site (http://www.teac-global.com/).

How to download the iPad/iPhone/iPod touch app

Search for “TEAC HR Streamer” in the App Store.

NOTE

Network module firmware is updated through TEAC HR Streamer.

We recommend that you regularly select this unit in TEAC HR

Streamer, and update it with the latest firmware. A pop-up window

recommending a firmware update will appear if one is available.

o Release is planned for an Android version (as of June 2018). See

the product website for details.

EN

7

a

b

c

d

Network connections

a NAS (Network Attached Storage)

Use to store audio files.

Operation as a UPnP server is necessary to use it as a media

server. MinimServer is the media server recommended for use

with this unit.

b Wi-Fi™ router

Use Wi-Fi to connect the iPad, iPhone or other device to this

unit and the NAS.

c iPad, iPhone, etc.

Install the app to control this unit.

d NT-505

This unit. The IP address is acquired from the DHCP server.

Connection example

iPad, iPhone, etc.

NAS

Wi-Fi™ router

NT-505

LAN cable

To Internet

o The Wi-Fi router must be connected to the

Internet when installing apps on the iPad, iPhone

or other device, when updating the NET firmware

of this unit, and when listening to Internet radio.

8

Connections (rear panel)

LRLR

A B

H

C D

FE G

Device that outputs

clock signal

Digital audio output

device

Digital audio output

device

CLOCK SYNC OUTDigital output

(COAXIAL)

Digital output

(OPTICAL)

RCA coaxial digital cable

BNC coaxial cable

Optical digital cable

RCA audio cables

XLR cables

USB cable

Included power cord

Audio input

(LINE IN, etc.)

Stereo amplifier or

powered speakers

Computer

c

Wall outlet

Connect cables for the pair set

for line output (page23).

Sound will only be output

from the selected pair.

If headphones are connected,

sound will stop being output

from the rear panel connectors.

The polarity of the XLR connec-

tors can be set so that either 2

or 3 is HOT (page23).

If you want to be able to

control the volume from the

amplifier, set LINE OUT LEVEL

to “FIXED 0dB” or “FIXED +6dB”

(page23).

Connect a set

of cables of one

type or the other.

Install the dedicated driver

on the computer before

connecting this unit to it

(page25).

EN

9

A ETHERNET port

Connect a commercially-available LAN cable to this port

when you want to connect this unit to a wired network or the

Internet.

o When switching input sources, this port is labeled “NET”.

B OPTICAL digital audio input connector

Use this to input digital audio. Connect the optical digital audio

output connector of an audio device to it.

Use a commercially-available optical digital cable with a

square connector (TOSLINK) for connection.

C RCA COAXIAL digital audio input connector

Use this to input digital audio. Connect the coaxial digital audio

output connector of an audio device to it.

Use a commercially-available RCA coaxial digital cable

for connection.

D CLOCK SYNC input (10MHz IN) connector

Use this to input a synchronization signal (clock sync).

To input a 10MHz oscillator signal, connect the oscillator output

here (page29).

Use a commercially available BNC coaxial cable for

connection.

o Clock sync is only possible when the input source is USB or

NET (including USB flash drives).

E Analog audio output (LINE OUT) connectors

These output 2 channels of analog audio. Connect these XLR or

RCA connectors to a stereo amplifier or powered speakers.

Use commercially available cables for connections.

XLR: balanced XLR cables

RCA: RCA audio cables

Connect this unit’s R connector to the R connector of the

amplifier and its L connector to the L connector of the amplifier.

o See “Line output” on page23 for analog output settings.

F USB port (rear)

Use this to input digital audio from a computer. Connect it to a

computer’s USB port.

Use a commercially-available USB2.0 cable (A-B type) for

this connection.

ATTENTION

Before connecting a computer that is running a Windows

OS, you must install the dedicated driver on the computer

(page25).

Proper connection is not possible with a computer that does

not have this driver installed.

G Maintenance port

This is used for maintenance. Do not connect anything to this

port unless instructed to do so by our service department.

H Power inlet (~IN)

Connect the supplied power cord here.

After all other connections are complete, connect the power

cord’s plug to a wall outlet.

V

Do not use any power cord other than the one

included with this unit. Use of other power cords

could result in fire or electric shock.

V

Unplug the cord from the outlet when not using

the unit for a long time.

V

Complete all other connections before turn-

ing the unit on.

o Carefully read the manuals of the devices that you are

connecting and follow their instructions when making

connections.

o Do not bundle connecting cables with power cords.

Doing so could cause noise.

o Connect all plugs completely.

10

Connections (front panel)

USB flash drives

Connect USB flash drives to the USB port on the front of the unit.

To play music files on a USB flash drive, set the input source to NET

and use the app for playback.

o For details, see the TEAC HR Streamer User’s Manual.

Digital audio input (OPT/COAX IN)

This input connector can be used for both optical (OPT) and coaxial

(COAX) connections.

Optical (OPT) connection

Use a commercially-available optical cable with a mini plug.

To enable this input, turn the SOURCE knob to select OPTICAL2.

Optical mini plug

Coaxial (COAX) connection

Use the included RCA conversion cable and a commercially-

available RCA coaxial digital cable.

To enable this input, turn the SOURCE knob to select COAXIAL2.

RCA conversion cable

RCA coaxial digital cable

EN

11

Connecting headphones

V

CAUTION

While wearing headphones, do not connect or disconnect them or

turn the unit on or off.

Doing so could result in a sudden loud noise that could harm your

hearing.

Before putting headphones on, always set the volume to

minimum (display should show “0” when set to “STEP (0-100)”

or “−∞ dB” when set to “dB”) (page17).

Using the remote control

Precautions for use

V

Misuse of batteries could cause them to rupture

or leak, which might result in fire, injury or the

staining of nearby materials. Please carefully read

and observe the precautions on page3.

o When using the remote control, point it toward the remote con-

trol signal receiver on the main unit from a distance of 5 m (16 ft)

or less. Do not place obstructions between the main unit and the

remote control.

o The remote control might not work if the remote control signal

receiver on the unit is exposed to direct sunlight or bright light. If

this occurs, try moving the unit.

o Beware that use of this remote control could cause the unin-

tentional operation of other devices that can be controlled by

infrared rays.

Installing batteries

Remove the cover from the back of the remote control and insert

two AAA batteries with their ¥/^ oriented as shown in the case.

Replace the cover.

When to replace batteries

If the distance required between the remote and the main unit

decreases or if the unit stops responding to the remote buttons,

replace both batteries with new ones.

Dispose of the used batteries according to the instructions on them

or requirements set by your local municipality.

12

Names and functions of parts (main unit)

A POWER switch

Use to turn the unit on and off.

o If the display is dark even though the POWER switch is set to

ON, the cause is usually one of the following.

o The power is on, but DIMMER (display brightness) is set

to OFF (page24).

o The automatic power saving function has put the unit

into standby.

o The power cord is disconnected.

To turn the unit on, press the STANDBY/ON button on the

remote control, or set the POWER switch to OFF once and

then back to ON.

B CLOCK indicator

This shows the clock synchronization status.

Lit: The unit is synchronized with the clock from the

CLOCK SYNC input (10MHz IN) connector.

Blinking: No clock is being input or the unit is not being

synchronized.

Unlit: No clock sync is occurring.

o Clock sync is only possible when the input source is USB or

NET (including USB flash drives).

o See page23 for clock sync settings.

C Digital audio input (OPT/COAX IN) connector

Use to input digital audio (page10).

Optical connection: Use an optical cable with a mini plug.

Coaxial connection: Use the included RCA conversion cable.

D SOURCE knob

Use to select the input source.

Use to change setting values when a menu item is shown.

Press to use as an ENTER button.

Turn when the menu is open to change the item shown or the

setting value.

E MENU button

Press to enter setting mode (page21).

Press when in setting mode to return to the previous screen.

F Remote control signal receiver

This receives signals from the remote control. When operating

the remote control, point it at the remote control signal receiver.

G USB port (front)

Connect USB flash drives here.

o To play music files on a USB flash drive, set the input source

to NET and use the app for playback.

o Do not connect a computer to the USB port on the front of

the unit. To input audio from a computer, connect it to the

USB port on the back of the unit.

o For details, see the TEAC HR Streamer User’s Manual.

A B C D E F G H I J

EN

13

H PHONES jack

Connect headphones with a 3.5mm (1/8") stereo mini plug here

(page11).

o This headphone amp circuit uses a four-pole connector with

independent left and right for grounding. Ordinary plugs

with 3 or 4 poles can be used.

o When headphones are connected to this unit, headphone

output will be turned on and audio will stop being output

from the analog audio output (LINE OUT) connectors on the

rear panel.

Wiring illustration

L+ R+ L− R−

I Display

This display shows information about the audio playing back

and menu screens.

J VOLUME knob

Use to adjust the volume. Turn right to increase and left to

decrease the volume.

o To enable adjustment of this unit’s analog audio output

volume, set LINE OUT LEVEL to VARIABLE (“Line output level”

on page23). This will enable adjustment of the analog

output level using this unit’s VOLUME knob.

o Volume settings are retained separately for analog audio

output and headphone output.

You can use the upconversion function with all input sources

(page22).

The relationships between input sampling frequencies and sampling

frequencies after upconversion are as follows.

Input source Upconversion setting

Digital

audio

input

USB OFF 2× Fs 4× Fs 8× Fs

DSD

256

DSD

512

Input sampling

frequency

Sampling frequency after upconversion

[kHz] [kHz] [MHz]

32 − 32 64 128 256 8.1 16.3

44.1 44.1 44.1 88.2 176.4 352.8 11.2 22.5

88.2 88.2 88.2 88.2 176.4 352.8 11.2 22.5

176.4 176.4 176.4 176.4 176.4 352.8 11.2 22.5

− 352.8 352.8 352.8 352.8 352.8 11.2 22.5

− 705.6 705.6 705.6 705.6 705.6 11.2 22.5

48 48 48 96 192 384 12.2 24.5

96 96 96 96 192 384 12.2 24.5

192 192 192 192 192 384 12.2 24.5

− 384 384 384 384 384 12.2 24.5

− 768 768 768 768 768 12.2 24.5

These values are not converted.

o The maximum upconversion is 8× Fs.

o Upconversion is not possible when the input is DSD.

o During MQA playback, 4× Fs upconversion will be used regard-

less of the setting.

Upconversion

14

Names and functions of parts (remote control)

When the main unit and the remote control both have buttons

with the same functions, this manual explains how to use one of

the buttons. The other corresponding button can be used in the

same manner.

a STANDBY/ON button

Press to put the unit into standby mode or turn it on.

b Input selection buttons

Use to select the playback source.

o The LINE button has no function.

c INFO button

Press to show information, including upconversion (page16).

d UPCONVERT button

Press to change the upconversion setting.

e FILTER button

Press to change the filter setting.

This changes the filter according to the input (PCM or DSD).

f MUTE button

Press to minimize the volume.

g DIMMER button

Press to adjust the brightness of the main unit’s display.

h HEADPHONE button

Press to turn headphone output on and off.

When headphone output is turned off, sound is output from

the analog audio output (LINE OUT) connectors.

i DISPLAY button

j MENU button

Press to enter setting mode (page21).

Press when in setting mode to return to the previous screen.

k Up/down (k/j) buttons

Use to select setting items.

l ENTER button

Press to confirm the selected item.

m VOLUME (+/−) buttons

Use to adjust the volume.

e

d

c

a

f

b

g

h

j

l

m

i

k

EN

15

Display

When on

Z

c

NT-505

NETWORK PLAYER

After the above messages appear, the input source will be shown on

the display.

Playback source information

The playback source information display will appear after turning

the unit on as well as after about 7 seconds pass without operation

when a setting screen is open.

The input signal format or volume is shown to the right of the playback

source. Press the DISPLAY button on the remote control to change

what is shown.

Display example

Playback source information displayed

Stopped

USB

check

Playback source

Shown when the connection is being checked

Playing back

USB

PCM

44.1k

Input signal format

Sampling frequency

Press the DISPLAY button on the remote control.

Volume display

USB

−45.5dB

Volume

Playback source name

This shows the name of the selected source.

The names on the display correspond to the selected connectors as

follows.

The names in parentheses appear when switching.

USB (USB)

USB port on the rear panel

COAX1 (COAXIAL 1)

RCA COAXIAL digital audio input connector on the rear panel

COAX2 (COAXIAL 2)

Coaxial connection with the digital audio input (OPT/COAX IN)

on the front panel

OPT1 (OPTICAL 1)

OPTICAL digital audio input connector on the rear panel

OPT2 (OPTICAL 2)

Optical connection with the digital audio input (OPT/COAX IN)

on the front panel

NET (NETWORK)

ETHERNET port

Bluetooth (Bluetooth)

Bluetooth device

Input signal status

This shows the input source signal status.

Check

The connection is being checked.

PCM 32kHz

PCM 44.1kHz

PCM 48kHz

PCM 88.2kHz

PCM 96kHz

PCM 128kHz

PCM 176.4kHz

PCM 192kHz

PCM 256kHz

PCM 352.8kHz

PCM 384kHz

PCM 705.6kHz

PCM 768kHz

DSD 2.8MHz

DSD 5.6MHz

DSD 11.2MHz

DSD 22.5MHz

These show the input signal type and sampling frequency.

16

Playback format information display

Press the INFO button on the remote control during playback to

show playback format information.

Example when the playback source is USB, COAX1, COAX2,

OPT1 or OPT2

o The input signal and playback signal displays will be the same

when the upconversion setting is “OFF”.

PCM DSD

44. 1kHz

11. 2MHz

Input signal sampling

frequency

Playback sampling

frequency

Playback signal

format

Input signal

format

Example when the playback source is NET or Bluetooth

LDAC PCM

48kHz

192kHz

Input signal sampling

frequency

Playback sampling

frequency

Codec

Playback signal

format

Volume display

Two types of volume can be shown: STEP and dB.

This is set by the VOLUME TYPE setting (page24).

The volume setting shown will be enlarged when you turn this unit’s

VOLUME knob.

VOLUME TYPE set to “STEP (0-100)”

Display example

VOL.

36

The maximum volume level is 100 and the minimum level is

0. Before connecting headphones, set the VOLUME knob to its

minimum value (0). Failure to do so might cause sudden loud

noises, which could harm your hearing or result in other trouble.

Display (continued)

VOLUME TYPE set to “dB”

Display example

VOL.

-62

.0dB

The maximum volume level is 0 and the minimum level is −∞

(negative infinity). Before connecting headphones, set the

VOLUME knob to its minimum value (−∞). Failure to do so might

cause sudden loud noises, which could harm your hearing or

result in other trouble.

The set output level is shown when LINE OUT LEVEL is set to “FIXED

0dB” or “FIXED +6dB”.

Example when VOLUME TYPE set to “dB”

USB

+ 0.0

dB

o If VOLUME TYPE is set to “STEP (0-100)”, “VOL. 86” will be shown

when set to “FIXED 0dB” and “VOL. 90” will be shown when set to

“FIXED +6dB”.

When headphones are not connected and LINE OUT LEVEL is set to

“OFF”, “VOL. 0” or “−∞ dB” will be shown.

Example when VOLUME TYPE set to “dB”

USB

− ∞ dB

When headphones are not connected and LINE OUT LEVEL is

set to FIXED or OFF

Turning the VOLUME knob will cause the following to be displayed.

LINE OUT LEVEL set to FIXED

VOL.

FIXED

LINE OUT LEVEL set to OFF

VOL.

OFF

EN

17

Basic operation

1 Shift the POWER switch to its ON position to

turn the unit on.

o If a stereo amplifier is connected to this unit, always turn its

power ON very last.

2 Turn the SOURCE knob to select the input

source.

The selected source appears on the display.

o You can also use the input selection buttons on the remote

control.

o If the input signal is not a digital audio signal or is an audio

signal format that is not supported by this unit, such as

Dolby Digital or DTS, no audio will be output. Set the digital

output of the connected device to PCM audio output.

o To play back audio files when this unit is set to USB, you

must first install a dedicated driver on the computer before

connecting them (page25).

o DSD data can only be played back when the input source is

USB or NET (including USB flash drives) or when using DoP

format digital input.

o To use NET or the front USB port, install the TEAC HR Streamer

(free) on a smartphone or tablet, and connect it to the same

network as the unit.

3 Operate the playback device.

Refer to the operation manual of that device.

4 Adjust the volume.

When using the line outputs

When LINE OUT LEVEL is set to VARIABLE, turn this unit’s VOLUME

knob to adjust the volume.

When LINE OUT LEVEL is set to any other setting, the volume

cannot be adjusted from this unit. Use the stereo amplifier or

other device connected to this unit to adjust the volume.

When headphones are connected to this unit

Turn this unit’s VOLUME knob to adjust the volume.

o When this unit’s VOLUME knob is enabled, the volume set-

ting will be shown.

18

Bluetooth® wireless technology

Bluetooth® notes

When using this unit with a mobile phone or other Bluetooth

devices, they should be no more than about 10 m (33 ft) apart.

Depending on the circumstances of use, however, the effective

transmission distance might be shorter.

Wireless communication with every device that supports Bluetooth

wireless technology is not guaranteed.

To determine the compatibility between this unit and another device

that supports Bluetooth wireless technology, refer to that device’s

operation manual or contact the shop where you purchased it.

Profiles

This unit supports the following Bluetooth profiles.

o A2DP (Advanced Audio Distribution Profile)

o AVRCP (Audio/Video Remote Control Profile)

In order to transfer audio using Bluetooth wireless transmission, the

Bluetooth device must support A2DP.

In order to control playback on the Bluetooth device, it must support

AVRCP.

Even if a Bluetooth device supports the same profiles, though, its

functions might differ according to its specifications.

Codecs

This unit supports the following codecs. It will automatically select

one of them during audio transfer.

o SBC

o AAC

o Qualcomm® aptX™

o Qualcomm® aptX™ HD

o LDAC

The unit will select the appropriate codec to use according to the

codec compatibility of the other Bluetooth device and communica-

tion conditions.

LDAC is an audio coding technology developed by Sony that enables

the transmission of High-Resolution (Hi-Res) Audio content, even over

a Bluetooth connection.

Unlike other Bluetooth compatible coding technologies such as SBC, it

operates without any down-conversion of the Hi-Res Audio content*,

and allows approximately three times more data** than those other

technologies to be transmitted over a Bluetooth wireless network with

unprecedented sound quality, by means of efficient coding and opti-

mized packetization.

* excluding DSD format contents

** in comparison with SBC (Subband Coding) when the bitrate of

990kbps (96/48 kHz) or 909kbps (88.2/44.1 kHz) is selected

NOTE

o You cannot select the codec to be used by pressing a button, for

example.

o Due to characteristics of Bluetooth wireless technology, playback

from a Bluetooth device will be slightly delayed compared to

playback from this unit.

Content protection

This unit supports SCMS-T as a form of content protection when

transmitting audio, so it can play protected audio.

Transmission security

This unit supports security functions during Bluetooth wireless

transmission in accordance with the Bluetooth standard specifica-

tions, but it does not guarantee the privacy of such transmissions.

TEAC CORPORATION will bear no responsibility should an informa-

tion leak occur during Bluetooth wireless transmission.

EN

19

Pairing with another Bluetooth device

Pairing this unit with another Bluetooth device is necessary the first

time it is used and when connecting to a different Bluetooth device

for the first time.

1 Turn the SOURCE knob to select Bluetooth.

Bluetooth

check

2 Enable Bluetooth transmission on the other

Bluetooth device.

3 Press and hold the SOURCE knob to enter pair-

ing mode.

PAIRING. . .

o “PAIRING…” blinks when pairing.

4 On the other Bluetooth device, select “NT-505”

(this unit).

After this unit enters pairing mode, pair with it from the other

Bluetooth device.

For details, refer to the operation manual of that Bluetooth

device.

After connection, the display will show the name of the con-

nected device, followed by the input source.

Display example

CONNECTED TO

iPhone 001

c

Bluetooth

VOL. 6

Playback from a Bluetooth device

o Pair this unit the first time you use it and when you want to

connect it with a different Bluetooth device for the first time

(page19).

o When pairing or connecting with another Bluetooth device,

they should be within a few meters of each other. If they are

too far apart, pairing and connection afterwards might become

impossible.

1 Enable Bluetooth transmission on the other

Bluetooth device.

2 Turn the SOURCE knob to select Bluetooth.

This sets the source to Bluetooth.

o You can also use the Bluetooth button on the remote control.

Display example

Bluetooth

check

c

CONNECTED TO

iPhone 001

c

Bluetooth

VOL. 6

This unit will search for paired devices and automatically con-

nect to one if found.

ATTENTION

Depending on the source device, you might also need to con-

duct connection operations on it.

If you are unable to connect it successfully, refer to the opera-

tion manual of the source device.

20

Changing the connected device

1 Press the SOURCE knob to show DEVICE SELECT.

The bottom line of the display shows the name of the last con-

nected device.

Display example

MENU

DEVICE SELECT

Player_1

Name of last connected device

2 Turn the SOURCE knob to show already paired

Bluetooth devices.

o The unit can remember a maximum of eight device pairings.

o If no paired device is available, the display will appear as

follows.

MENU

DEVICE SELECT

NO PAIRED DEVICE

o Press and hold the ENTER button to enter pairing mode

(page19).

o The first 16 characters of the device name are shown.

o If characters other than English letters and numbers are

included in the device name, it will not be shown properly.

3 Press the SOURCE knob to connect.

After connection, the display will show the input source.

ATTENTION

Regardless of the connection status of this unit and the other

Bluetooth device, if the input source is not shown, restart both

this unit and the other device and then connect them again.

NOTE

Depending on the source device, you might also need to con-

duct connection operations on it.

If you are unable to connect it successfully, refer to the opera-

tion manual of the source device.

Bluetooth® wireless technology (continued)

4 Start playback on the other Bluetooth device.

o Confirm that the volume is turned up on the other Bluetooth

device. If you do not turn up the volume on the playback

device, no sound might be output from this unit.

NOTE

Press and hold the MENU button to clear a paired device.

La page est en cours de chargement...

TEAC NT-505 Manuel utilisateur

TEAC NT-505 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents