TEAC NR-7CD Le manuel du propriétaire

NR-7CD

D01307621A

Z

Network CD Integrated Amplifier

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

For information about this unit’s network functions,

see the TEAC HR Streamer User’s Manual.

The Owner’s Manual and TEAC HR Streamer User’s

Manual can be downloaded from the TEAC Global

Site (http://www.teac-global.com/).

To play back files on USB flash drives and to use the

unit connected to a network, install the dedicated

app (free) on a smartphone or tablet, and connect it

to the same network as the unit.

ENGLISH

FRANÇAIS

ESPAÑOL

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete

outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the man-

ufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume)

from earphones or headphones can cause hearing loss.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batter-

ies: there is danger of explosion if a battery is replaced with

an incorrect type of battery. Replace only with the same or

equivalent type.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

EN

3

V

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and

negative (^) orientations.

o Use batteries of the same type. Never use different types of bat-

teries together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batter-

ies together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The

batteries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

Laser information

This product contains a semiconductor laser system inside the cabi-

net and is classified as a “CLASS 1 LASER PRODUCT”.

To prevent being exposed to the laser beam, do not try to open the

enclosure.

Laser:

Type: EP-C101

Manufacturer: GUANGDONG EVER BRIGHT GROUP CO.,LTD.

Laser output: Less than 0.3 mW

Wavelength: 790 ±25 nm

Model for USA

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified

as class ! laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

For European Customers

Disposal of electrical and electronic equipment

and batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/

accumulators should be disposed of separately from the

municipal waste stream via collection facilities designated by

the government or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valuable

resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those

elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

4

Wireless equipment precautions

Compliance of radio transmitter and

interference

Model for USA

Declaration of Conformity

Responsible party: TEAC AMERICA, INC.

Address: 1834 Gage Road, Montebello, California,

U.S.A.

Telephone number : 1-323-726-0303

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

Labeling of authorization

FCC ID: XEG-NR7CD

Model for Canada

Compliance of radio transmitter

This device complies with Industry Canada RSS standard(s).

Operation is subject to the following two conditions:

1) This device may not cause interference

2) This device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

Labeling of authorization

IC: 1559C-NR7CD

Compliance of interference

This Class B digital apparatus complies with Canadian ICES-003.

Model for EEA (European Economic Area)

This product has the function of broadband transmitter using

2.4GHz Band.

Use frequency range: 2400 MHz – 2480 MHz

Maximum output power: Bluetooth® Class 2 (less than 2.5 mW)

Hereby, TEAC Corporation declares that the radio

equipment type is in compliance with Directive

2014/53/EU., and the other Directives, and

Commission Regulations.

The full text of the EU declaration of conformity is available at the

following internet address: Please contact us by e-mail.

http://www.teac-audio.eu/en/

TEAC Corporation

1-47 Ochiai, Tama-shi, Tokyo, 206-8530, Japan

CAUTION

Authorization of wireless devices are different in countries or

regions. Please use only in the country where you purchased the

product.

o Depending on the country, restrictions on the use of Bluetooth

wireless technology might exist.

Confirm the laws and regulations of the country or region where

you want to use the unit before use.

Radiation Exposure requirements

This equipment meets the regulation, which is recognized interna-

tionally, for the case of human exposure to radio waves generated

by the transmitter.

Statement of compliance

Model for USA

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment and meets the FCC radio fre-

quency Exposure Guidelines.

Model for Canada

This equipment complies with IC RSS-102 radiation exposure limits set

forth for an uncontrolled environment.

Model for EEA (European Economic Area)

This equipment complies with EN.62311; Assessment of electronic

and electrical equipment related to human exposure restrictions

for electromagnetic fields; the harmonised standard of DIRECTIVE

2014/53/EU.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

EN

5

Trademarks and copyrights

“DSD” is a registered trademark.

The Bluetooth® word mark and logos are registered trademarks

owned by Bluetooth SIG, Inc. and any use of such marks by TEAC

CORPORATION is under license.

Qualcomm aptX is a product of Qualcomm Technologies International,

Ltd.

Qualcomm is a trademark of Qualcomm Incorporated, registered in

the United States and other countries, used with permission. aptX is

a trademark of Qualcomm Technologies International, Ltd., registered

in the United States and other countries, used with permission.

Wi-Fi is a trademark or registered trademark of Wi-Fi Alliance.

Apple, iPad, iPhone and iPod touch are trademarks of Apple Inc.,

registered in the U.S. and other countries. App Store is a service mark

of Apple Inc.

LDAC™ and LDAC logo are trademarks of Sony Corporation.

Other company names, product names and logos in this document

are the trademarks or registered trademarks of their respective

owners.

Information about copyrights and licensing related to open-source

software is provided in the separate “Important Notice Regarding

Software” document.

Information for interference

(FCC requirements)

This equipment has been tested and found to comply with the lim-

its for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference

by one or more of the following measures.

o Reorient or relocate the equipment and/or the receiving

antenna.

o Increase the separation between the equipment and receiver.

o Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

o Consult the dealer or an experienced radio/TV technician for

help.

6

Contents

IMPORTANT SAFETY INSTRUCTIONS ...............................2

Wireless equipment precautions ...................................4

Trademarks and copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Included items ....................................................6

Downloading the remote app .....................................6

Using the TEAC Global Site .........................................6

Product registration ...............................................6

Before use .........................................................7

Maintenance ......................................................7

Using the remote control ..........................................7

Discs ..............................................................8

Connecting speakers ..............................................9

Connections ......................................................10

Network connections .............................................12

Names and functions of parts (remote control) ....................13

Names and functions of parts (main unit) .........................14

Connecting headphones .........................................15

Upconversion ....................................................16

Display ...........................................................17

Basic operation ...................................................18

Listening to CDs ..................................................21

Bluetooth® wireless technology ...................................23

Settings ..........................................................25

Troubleshooting ..................................................27

Specifications .....................................................29

Thank you for choosing TEAC.

Read this manual carefully to get the best performance from this

unit.

After reading it, keep it in a safe place for future reference.

For information about this unit’s network functions, see the TEAC HR

Streamer User’s Manual.

o The Owner’s Manual and TEAC HR Streamer User’s Manual can be

downloaded from the TEAC Global Site (http://www.teac-global.

com/).

o To use network functions and USB playback, you must also use

an iPad or other iOS device that has the dedicated app (free)

installed and is connected to the same network as the unit.

Check to be sure the box contains all the included items shown

below.

Please contact the store where you purchased this unit if any of these

items are missing or have been damaged during transportation.

Power cord × 1

Remote control (RC-1328) × 1

Batteries for remote control (AAA) × 2

Felt pads × 3

Owner’s manual (this document, including warranty) × 1

o For information about the warranty, users living in the USA and

Canada should see page 86 and the back cover (warranty

document). Users living in Europe and other regions should see

page 87.

o The TEAC HR Streamer User’s Manual can be downloaded from

the TEAC Global Site (http://www.teac-global.com/).

Downloading the remote app

To use network and USB playback functions, you must also use an

iPad or other device that has the dedicated app (free) installed and

is connected to the same network.

How to download the app for iOS devices including iPad

Search for “TEAC HR Streamer” in the App Store.

o Release is planned for an Android version (as of January 2017).

See the product website for details.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

1) Open the TEAC Global Site.

2) In the TEAC Downloads section, click the desired language to

open the Downloads website page for that language.

NOTE

If the desired language does not appear, click Other Languages.

3) Click the “Search by Model Name” section to open the

Downloads page for that product. (Users in Europe should click

the product name in the “Products” section instead.)

4) Select and download the updates that are needed.

Product registration

Customers in the USA, please visit the following TEAC website to

register your TEAC product online.

http://audio.teac.com/support/registration/

Included items

EN

7

V

Placement precautions

o Do not install this unit in a location that could become hot.

This includes places that are exposed to direct sunlight or near

a radiator, heater, stove or other heating equipment. Moreover,

do not place it on top of an amplifier or other equipment that

generates heat. Doing so could cause discoloration, deformation

or malfunction.

o When installing this unit, leave a little space (at least 3 cm or 1")

between it and walls and other devices in order to allow good

heat dissipation.

If you put it in a rack, for example, leave at least 5 cm (2") open

above it and at least 10 cm (4") open behind it.

Failure to provide these gaps could cause heat to build up inside

and result in fire.

Note about pinpoint feet

High-precision metal pinpoint feet are attached firmly to the bot-

tom plate of this unit.

The stands for these feet are loose, but when the unit is placed in

position, it is supported by these pinpoint feet, which will effectively

disperse vibrations.

Chassis Pinpoint foot (metal)

Foot-stand (metal)

Screws that attach

foot-stand

o The included felt pads are intended to protect the surface where

the unit is placed. Apply them to the bottoms of the foot-stands.

Maintenance

Wipe dirt from the top cover and other panel surfaces using a

soft cloth that has been slightly dampened with a diluted neutral

cleanser.

Do not wipe with chemical cleaning cloths, thinner or other chemi-

cal agents. Doing so could damage the surface.

V

For your safety, disconnect the power cord from

the outlet before cleaning.

Before use Using the remote control

Precautions for use

V

Misuse of batteries could cause them to rupture or

leak, which might result in fire, injury or the stain-

ing of nearby materials. Please carefully read and

observe the precautions on page 3.

o When using the remote control, point it toward the remote con-

trol signal receiver on the main unit from a distance of 5 m (16 ft)

or less. Do not place obstructions between the main unit and the

remote control.

o The remote control might not work if the remote control signal

receiver on the unit is exposed to direct sunlight or bright light. If

this occurs, try moving the unit.

o Beware that use of this remote control could cause the unin-

tentional operation of other devices that can be controlled by

infrared rays.

Installing batteries

Remove the cover from the back of the remote control and insert

two AAA batteries with their ¥/^ oriented as shown in the case.

Replace the cover.

When to replace batteries

If the distance required between the remote and the main unit

decreases or if the unit stops responding to the remote buttons,

replace both batteries with new ones.

Dispose of the used batteries according to the instructions on them

or requirements set by your local municipality.

8

Discs

o If the side of the disc that has the data encoded on it (unlabeled

side) becomes dirty with fingerprints or dust, use a soft cloth to

wipe the surface from the center directly toward the edge.

Always clean discs before storing them. Leaving a disc in an

unclean state might degrade its sound quality.

o Never use record cleaners, antistatic treatments, thinners or

similar chemicals to clean discs. Such chemicals could harm the

surface of the disc.

o Do not leave discs in places that are exposed to direct sunlight or

that are very humid or hot.

o When writing something on the label side of a disc, use a felt tip

permanent marker. The use of a ballpoint pen or other pen with

a hard tip could damage the disc, making it unplayable.

o After you finish playing a disc, always put it back into its case for

storage. Failure to do so could result in warping and scratches.

o Do not apply labels or other materials to discs. Do not use a disc

that has sticky residue left on its surface after removing tape or

a sticker, for example. If such a disc is loaded, it might become

stuck in the unit or damage the unit.

o Never use commercially-available CD stabilizers. Doing so could

make the disc unplayable or damage the unit.

o Do not use cracked discs because they could damage the unit.

o Never use discs with irregular shapes, including heart-shaped

and octagonal discs, because they could damage the unit.

o Do not use printable discs, which allow printing on the label

side. Since the surface of such a disc has been specially treated,

if loaded, it might become stuck in the unit or damage the unit.

If you have any questions about how to handle a CD-R or CD-RW

disc, contact the manufacturer of the disc directly.

The following marks appear on disc labels and disc cases. This unit

can play discs that have these marks without using an adapter.

This unit cannot play discs that do not have these marks.

Types of discs that can be played on this unit and

their marks

CDs with the “COMPACT disc DIGITAL AUDIO” logo (12 cm,

8 cm)

o This logo appears on disc labels and packages.

If you try to play any other type of disc with this unit, loud

noises that could damage speakers or harm hearing might

occur. Never try to play any type of disc other than those

shown above.

o This unit cannot play DVD video, DVD audio, video CD, DVD-ROM

and CD-ROM discs, for example.

o This unit might not be able to properly play Dual Discs, Copy

Control CDs or other special CDs that do not conform to the

Red Book CD standard. Operation and sound quality cannot be

guaranteed when special discs are used in this unit. If playback of

a special disc should cause trouble, contact the seller of the disc.

CD-R/CD-RW discs

This unit can play CD-R/CD-RW discs that are in audio CD format.

o Be sure to finalize discs created by CD recorders.

Depending on the quality of the disc and the condition of the

recording, playback might not be possible. For details, see

the operation manual for the device you are using.

Handling discs

o Load discs with their labeled sides up.

(CDs only have one playable side.)

o To remove a disc from its case, always press down on the center

of the case first and then hold the disc by its edges.

Removal from case Holding by edges

o Be careful when handling discs. If the side that contains the data

(unlabeled side) is scratched, smudged with fingerprints or oth-

erwise dirty or marred, errors could occur during playback.

EN

9

Notes about speaker cables

o Use commercially-available speaker cables to connect the

speakers.

o Use the shortest speaker cables possible. The longer the cable,

the greater the resistance value and the more that damping

performance is reduced. Moreover, length also increases imped-

ance and capacitance, degrading the sound quality of high

frequencies.

o Use left and right speaker cables that have the same length.

How to connect speaker cables

Use commercially-available speaker cables to connect the ¥

terminal of the unit to the ¥ terminal of the speaker and the ^

terminal of the unit to the ^ terminal of the speaker.

o Use speakers with at least 4Ω impedance.

o If the exposed tip of the core wire of a speaker cable contacts

another cord or terminal, a short could occur.

Never allow a speaker cable to short.

o Do not connect more than one amplifier to a speaker.

o Do not bundle speaker cables with power cords. Doing so could

cause noise.

V

The power plug should always be disconnected

when connecting speaker cables.

When using bare wires

Loosen the cap and insert the core wire into the hole in the termi-

nal. Then, tighten the cap.

When using spade lugs

Loosen the cap and insert the lug between the cap and base of the

terminal. Then, tighten the cap.

o When using a spade lug to connect, use one with an inside

diameter of at least 8 mm (3/8").

When using banana plugs

With the cap tightened, insert the plug into the opening in the end

of the terminal.

o Carefully read the instructions for the banana plugs that you are

using.

Notice about the European model

In accordance with European safety regulations, connecting

banana plugs to speaker terminals is not allowed on European

models.

The holes into which banana plugs could be inserted have been

covered with black caps.

Connect speakers using bare wires or spade lugs.

If a black cap should become separated from its terminal, return

it to its original position.

Connecting speakers

10

LR

A B

C D F

E

A

Connections

Digital audio output

device

Digital audio output

device

DIGITAL OUT

(COAXIAL)

DIGITAL OUT

(OPTICAL)

RCA coaxial digital cable

Optical digital cable

RCA audio cables

Included power cord

c

Wall outlet

Right speaker Left speaker

Analog audio output device

Audio output

(LINE OUT, etc.)

LAN cable

USB flash drive

EN

11

A SPEAKER terminals

Use commercially-available speaker cables to connect the ¥

terminal of the unit to the ¥ terminal of the speaker and the ^

terminal of the unit to the ^ terminal of the speaker (page 9).

B Analog audio input (LINE IN) connectors

Use these to input 2-channel analog audio signals. Connect an

analog audio output device to these RCA connectors.

Use commercially-available cables for connections.

Connect this unit’s R input connector to the R output connec-

tor of the audio output device, and this unit’s L input connector

to the L output connector of the other device.

RCA audio cables

L

R

L

R

C Digital audio input connectors

COAXIAL

Use this to input digital audio. Connect the coaxial digital audio

output connector of a digital audio device to it.

Use a commercially-available RCA coaxial digital cable

for connection.

OPTICAL

Use these to input digital audio. Connect optical digital audio

output connectors of digital audio devices to them.

Use commercially-available optical digital cables with

rectangular connectors for connection.

D Power inlet (~IN)

Connect the supplied power cord here.

After all other connections are complete, connect the power

cord’s plug to a wall outlet.

V

Do not use any power cord other than the one

included with this unit. Use of other power cords

could result in fire or electric shock. Unplug the

cord from the outlet when not using the unit for a

long time.

E ETHERNET port

Connect a commercially-available LAN cable to this port when

you want to connect this unit to a wired network or the Internet.

o When switching input sources, this port is labeled “NET”.

F USB port

Connect USB flash drives that contain audio files here.

o USB flash drive playback requires operation using a device

(with the dedicated app) that is on the same network as this

unit.

V

Complete all other connections before turn-

ing the unit on.

o Carefully read the manuals of the devices that you are

connecting and follow their instructions when making

connections.

o Do not bundle connecting cables with power cords. Doing

so could cause noise.

o Connect all plugs completely.

12

Network connections

a NAS (Network Attached Storage)

Use to store audio files.

Operation as a UPnP server is necessary to use it as a media

server. MinimServer is the media server recommended for use

with this unit.

b Wi-Fi

™

router

Use Wi-Fi to connect the iPad or other device to this unit and

the NAS.

c iPad or other device

Install the app to control this unit (page 6).

d NR-7CD

This unit. The IP address is acquired from the DHCP server.

Connection example

a

b

c

d

iPad or other device

NAS

Wi-Fi™ router

NR-7CD

LAN cable

To Internet

o The Wi-Fi router must be connected to the

Internet when installing apps on the iPad or

other device, when updating the NET firmware

of this unit, and when listening to Internet radio.

EN

13

Names and functions of parts (remote control)

d FILTER button

Use to change the filter setting.

This changes the filter according to the input (PCM or DSD).

e SHUFFLE button

Use to change the shuffle playback setting.

f REPEAT button

Use to change the repeat playback setting.

g Stop (

8

) button

Press to stop CD, NET or Bluetooth playback.

h MUTE button

Press this button to temporarily mute the sound.

i METER button

Use to set level meter brightness and turn operation on and off

(page 20).

j DIMMER button

Use this button to change the brightness of the display.

k MENU button

Use to enter setting mode (page 25).

Press when in setting mode to return to the previous screen.

l ENTER button

Press to confirm the selected item.

m Up/down (k/j) buttons

Use to select setting items.

n Skip (

.

/

) buttons

During CD playback

Use to skip to the previous or next track.

Press and hold for at least one second during playback to

search forward/backward (page 22).

During NET and Bluetooth playback

Use to skip to the previous or next track in the playlist.

o Play/pause (7/9) button

When the input source is CD, NET or Bluetooth and playback is

stopped or paused, press to start playback.

Press during playback to pause.

p VOLUME (+/−) buttons

Use to adjust the speaker and headphone volumes.

o When the main unit and the remote control both have but-

tons with the same functions, this manual explains how to

use one of the buttons. The other corresponding button can

be used in the same manner.

e

d

c

a

f

b

g

h

i

j

k

l

m

n

o

p

a STANDBY/ON button

Press to put the unit into standby mode or turn it on (page

18).

b Input selection buttons

Use to select the playback source.

o The USB button is not used with this unit.

Select NET and use the app to control USB flash drive

playback.

o LINE 1 is the only line input for this device.

c UPCONVERT button

Use to show and change the upconversion setting (page 16).

14

Names and functions of parts (main unit)

A Level meters

These show the output levels.

B Disc tray

Load a disc here.

C POWER switch

Use to turn the unit on and off (page 18).

o If the display or level meters are dark even though the

POWER switch is set to ON, one of the following conditions

is possible.

o The power is on, but the display brightness is set to

DIMMER 0 and/or the level meter operation setting is

DIM0 or OFF (page 26).

o The automatic power saving function has activated, put-

ting the unit into standby (page 27).

o The power cord is disconnected.

D SOURCE knob

Use to select the input source.

Use to change setting values when a menu item is shown.

Turn when the menu is open to change the item shown or the

setting value.

E ENTER button

Press to confirm the selected item.

o Press when the unit is in standby to turn it on (page 19).

F MENU button

Use to enter setting mode (page 25).

Press when in setting mode to change the setting item.

G UPCONVERT button

Use to show and change the upconversion setting (page 16).

H Display

This display shows information about the audio playing back

and menu screens (page 17).

I Stop (8) button

Press to stop CD, NET or Bluetooth playback.

J Play/pause (7/9) button

When the input source is CD, NET or Bluetooth and playback is

stopped or paused, press to start playback.

Press during playback to pause.

K Remote control signal receiver

This receives signals from the remote control. When operating

the remote control, point it at the remote control signal receiver.

EDC F G H I J K L M N O

A B A

EN

15

L Skip (.//) buttons

During CD playback

Use to skip to the previous or next track.

Press and hold for at least one second during playback to

search forward/backward (page 22).

During NET and Bluetooth playback

Use to skip to the previous or next track in the playlist.

M Tray open/close (-) button

Press to open and close the disc tray.

N VOLUME knob

Use to adjust the volume. Turn right to increase and left to

decrease the volume.

o Volume settings are saved separately for speaker and head-

phone outputs.

O PHONES jack

Connect headphones (3.5mm stereo mini plug) here.

o This headphone amp circuit uses a four-pole connector with

independent left and right for grounding. Ordinary plugs

with 3 or 4 poles can be used.

o If headphones are connected to this unit, audio will not be

output from the SPEAKER terminals on the rear panel.

NOTE

The following buttons on the unit and the remote control function

with CD, NET and Bluetooth playback.

Stop (8) button

Play/pause (7/9) button

Skip (.//) buttons

o This unit cannot be used to create playlists, for example, on

another unit connected to it. Playlists must be created and

other settings must be made to enable playback on connected

devices.

Connecting headphones

Wiring illustration

L+ R+ L− R−

V

CAUTION

While wearing headphones, do not connect or dis-

connect them or turn the unit on or off.

Doing so could result in a sudden loud noise that

could harm your hearing.

Always set the volume to minimum (−∞ dB) before

putting headphones on.

16

Upconversion

The conversion function can be used when digital audio is being

input (CD, NET*, Bluetooth, OPT1, OPT2, COAX).

Press the UPCONVERT button to show the current setting.

Press it again to change the upconversion setting.

*For USB flash drive playback, set the input source to NET.

OFF

DSD

2Fs

4Fs

8Fs

Display example

UPCONV

DSD

OFF

Upconversion will not occur.

The original input signal is sent as is directly to the D/A converter.

DSD

2Fs

4Fs

8Fs

The upconversion shown will be used.

The relationships between input sampling frequencies and sam-

pling frequencies after upconversion are as follows.

Input source Upconversion setting

Input sampling

frequency

OFF 2Fs 4Fs 8Fs DSD

Sampling frequency after upconversion

[kHz] [kHz] [MHz]

32 32 64 128 256 8.0

44.1 44.1 88.2 176.4 352.8 11.2

88.2 88.2 88.2 176.4 352.8 11.2

176.4 176.4 176.4 176.4 352.8 11.2

352.8 352.8 352.8 352.8 352.8 11.2

48 48 96 192 384 12.2

96 96 96 192 384 12.2

192 192 192 192 384 12.2

384 384 384 384 384 12.2

DSD [MHz] [MHz] [MHz]

2.8 2.8 2.8 2.8 2.8 2.8

5.6 5.6 5.6 5.6 5.6 5.6

These values are not converted.

EN

17

Display

When the unit is turned on

WELCOME

c

TEAC

NR-7CD

After messages like the above appear, the input source will be

shown on the display.

Input source information

The input source information screen will appear after turning the

unit on as well as after about 10 seconds pass without operation on

a setting screen.

Display example

-

51

.5

OPT1

PCM 44k

Input signal status Volume

Input source name

o Turning the VOLUME knob will change the volume, and the vol-

ume will appear to the right of the input signal status.

Input source name

This shows the name of the selected source.

The names on the display correspond to the selected connectors as

follows.

CD

CD player in this unit

NET

ETHERNET port, USB port

COAX

RCA COAXIAL digital audio input connector

OPT1

Optical digital audio input connector 1

OPT2

Optical digital audio input connector 2

LINE

Analog audio input connectors

o When using Bluetooth, the name of the connected device is

shown.

Input signal status

This shows the input source signal status.

UNLOCK!

The unit cannot synchronize with the input signal.

NOT AUDIO!

A signal with a format that cannot be played is being received.

NETWORK!

The input source is NET, but the unit is not connected to a

network.

READY

The input source is NET and it is connected, but no audio signal

is being received.

WAV 44k

DSD 2.8M

DSD 5.6M

FLAC96k, etc.

These are abbreviations of the input signal type and sampling

frequency.

SBC

AAC

aptX

LDAC

When the input source is Bluetooth, abbreviations of the codec

type and sampling frequency are shown.

Volume display

The volume setting shown will be enlarged when you turn this

unit’s VOLUME knob.

Display example

Volume -

60

.0dB

18

Basic operation

1 Turn on the connected input source devices.

2 Shift the POWER switch to its ON position to

turn the unit on.

3 Turn the SOURCE knob to select an input

source.

The input sources will be shown in the following order

CD

NET

Bluetooth

OPT1

OPT2

COAX

LINE

o You can also use the input selection buttons on the remote

control.

o If the input signal is not a digital audio signal or is an audio

signal format that is not supported by this unit, such as

Dolby Digital or DTS, “NOT AUDIO!” will appear on the screen

and no audio will be output. Set the digital output of the

connected device to PCM audio output.

o To use NET or the USB port, install the dedicated app (page

6) on an iPad or other device, and connect it to the same

network as this unit (page 12).

4 Start playback on the source device.

Refer to the operation manual of that device.

o CD and Bluetooth operation are explained in later sections

of this manual.

EN

19

5 Play the source, and then adjust the volume by

turning the VOLUME knob.

o The volume operation screen will appear.

Automatic power saving function

When the automatic power saving function is ON, this unit will auto-

matically enter standby mode if there is no playback and it is not

operated for 30 minutes (page 27).

o Even when audio is playing back, automatic power saving will

also function if the VOLUME knob is set to a value at which sound

cannot be heard.

Turning the unit on from standby

o Press the remote control STANDBY/ON button.

o Press the ENTER button on the front of the unit.

20

Dimmer

Each time you press the remote control DIMMER button, the bright-

ness of the display changes as follows (page 26).

DIMMER3

c

DIMMER2

c

DIMMER1

c

DIMMER0

(normal brightness)

(Unlit)

Muting playback

If you want to temporarily mute the volume of this unit, press the

MUTE button on the remote control.

Press the MUTE button on the remote control again to return to the

previous volume level.

o When muted, adjusting the volume will unmute it.

Level meters

Press the remote control METER button to change level meter

brightness and turn the meters on and off.

DIM3

c

DIM2

c

DIM1

c

DIM0

c

OFF

(Unlit)

(Unlit, meters stopped)

Basic operation (continued)

La page est en cours de chargement...

TEAC NR-7CD Le manuel du propriétaire

TEAC NR-7CD Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents