Wacker Neuson CT36-8A Manuel utilisateur

Operator’s Manual

Notice d'emploi

Walk-Behind Trowels

Truelle mécanique

CT36/CT36A

CT48/CT48A

Type

Document

Date

Version

Language

CT36/CT36A, CT48/CT48A

5100022588

0618

07

E

N-FR

5100022588

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

CALIFORNIA Proposition 65 Warning

wc_tx004643en.fm

3

CALIFORNIA Proposition 65 Warning

WARNING

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

WARNING

Breathing diesel engine exhaust exposes you to chemicals known to the State of

California to cause cancer and birth defects or other reproductive harm.

► Always start and operate the engine in a well-ventilated area.

► If in an enclosed area, vent the exhaust to the outside.

► Do not modify or tamper with the exhaust system.

► Do not idle the engine except as necessary.

For more information go to www.P65warning.ca.gov/diesel.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING

Batteries, battery posts, terminals and related accessories contain lead and lead

compounds, and other chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

CALIFORNIA Proposition 65 Warning

wc_tx004643en.fm

4

Notes

wc_tx004116gb_FM10.fm

5

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered by

this manual

n

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine Item Number Machine Item Number

CT 36-6 5000009443

5000620830

CT 48-9 5000009453

5000620838

CT 36-9 5000009444

5000620833

CT 36-9V 5000009447

5000620834

CT 36-5A 5000009438

5000620106

5000620829

5200016256

CT 48-8A 5000009449

5000620837

CT 36-8A 5000009439

5000620831

CT 48-11A 5000009450

5000620835

CT 36-8A-V 5000009442

5000620832

CT 48-13A-V 5000009452

5000620836

wc_gr010106

m3/hrm3/hr

Type/ModelType/Model

gpmgpm

Rev.Rev.

MADE IN USA MADE IN USA

kWkW

lbslbs

kgkg

Item NumberItem Number

Manuf.Yr.Manuf.Yr.

hphp

ftft

m

Serial NumberSerial Number

150188150188

Serial Number:

wc_tx004116gb_FM10.fm

6

Machine

documentation

■ From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

■ Keep a copy of the Operator’s Manual with the machine at all times.

■ For spare parts information, please see your Wacker Neuson Dealer, or visit the

Wacker Neuson website at http://www.wackerneuson.com/.

■ When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

■ This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

■ Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

■ The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change any

portion of this information without notice.

■ The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

wc_tx004116gb_FM10.fm

7

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

■ Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

■ Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

■ Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

■ Serious injury hazards to the operator and persons in the work area

■ Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

wc_tx004116gb_FM10.fm

8

Notes

2016-CE-CT36_CT48_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051, USA

Product

Product category

Product function

Item number

CT36-5A, CT36-8A, CT36-8A-V, CT36-6, CT36-9,

CT36-9-V, CT48-8A, CT48-11A, CT48-13A-V, CT48-9

Trowel

To smooth and finish semi-cured concrete

5000620829, 5000620830, 5000620831, 5000620832,

5000620833, 5000620834, 5000620835, 5000620836,

5000620837, 5000620838

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2014/30/EU, EN12649

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6, 85084

Reichertshofen, Germany

Menomonee Falls, WI, USA, 11.05.16

Original Declaration of Conformity

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Scott Grahl

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

Table of Contents

Walk-Behind Trowels

wc_bo5100019763_07TOC.fm

11

CALIFORNIA Proposition 65 Warning 3

Foreword 5

EC Declaration of Conformity 9

1 Safety Information 13

1.1 Signal Words Used in this Manual ..................................................... 13

1.2 Machine Description and Intended Use ............................................. 14

1.3 Operating Safety ................................................................................ 15

1.4 Service Safety .................................................................................... 17

1.5 Operator Safety while Using Internal Combustion Engines ............... 19

2 Labels 20

2.1 Label Locations .................................................................................. 20

2.2 Label Meanings .................................................................................. 21

3 Lifting and Transporting 25

3.1 Lifting the Machine ............................................................................. 25

3.2 Transporting the Machine ................................................................... 27

4 Operation 28

4.1 Preparing the Machine for First Use ................................................... 28

4.2 Recommended Fuel ........................................................................... 28

4.3 Refueling the Machine ........................................................................ 29

4.4 Installing the Blades ........................................................................... 30

4.5 Installing and Adjusting the Handle .................................................... 31

4.6 Controls .............................................................................................. 35

4.7 Position of the Operator ..................................................................... 35

4.8 Braking System .................................................................................. 36

4.9 Testing the Engine Control Module .................................................... 36

4.10 Optional Weights ................................................................................ 37

4.11 Before Starting the Machine ............................................................... 37

4.12 Starting, Operating, and Stopping the Machine ................................. 38

4.13 Emergency Shutdown Procedure ....................................................... 41

Table of Contents Walk-Behind Trowels

wc_bo5100019763_07TOC.fm

12

5 General Maintenance 42

5.1 Maintaining the Emission Control System .......................................... 42

5.2 Periodic Maintenance Schedule ......................................................... 42

5.3 Belt Replacement ............................................................................... 43

5.4 Trowel Lubrication .............................................................................. 44

5.5 Long-Term Storage ............................................................................. 44

5.6 Machine Disposal and Decommissioning ........................................... 45

6 Engine Maintenance 46

6.1 Periodic Maintenance Schedule: Wacker Neuson WM170 ................ 46

6.2 Engine Oil: Wacker Neuson WM 170 ................................................. 47

6.3 Periodic Maintenance Schedule: Honda GX 160 ............................... 48

6.4 Oil Recommendations ........................................................................ 49

7 Technical Data 50

7.1 Dimensions ......................................................................................... 50

7.2 Engine: Honda .................................................................................... 51

7.3 Engine: Wacker Neuson ..................................................................... 54

7.4 Trowel ................................................................................................. 56

7.5 Sound and Vibration Specifications .................................................... 57

8 Troubleshooting 58

9 Emission Control Systems Information

and Warranty 59

9.1 Emission Control Systems Warranty Statement ................................. 59

10 AEM Safety Manual 60

wc_si000959gb_FM10.fm

13

Walk-Behind Trowels Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000959gb_FM10.fm

14

Safety Information Walk-Behind Trowels

1.2 Machine Description and Intended Use

This machine is a walk-behind concrete finishing trowel. The Wacker Neuson

Walk-Behind Trowel consists of a frame onto which are mounted a gasoline

engine, a fuel tank, a gearbox, and a control handle. A set of four metal blades is

connected to the gearbox and is surrounded by a ring guard. The engine rotates

the blades through the gearbox and clutch mechanism. The rotating blades ride on

the surface of curing concrete, creating a smooth finish. The operator walks behind

the machine and uses the handle to control speed and direction of the machine.

This machine is intended to be used for floating and burnishing curing concrete.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine to finish inappropriate materials such as slurries, sealers, or

epoxy finishes

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

■ Heat, noise, exhaust, and carbon monoxide from the engine

■ Chemical burns from curing concrete

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes, fuel spillage from improper lifting technique

■ Personal injury from improper lifting techniques or operating techniques

■ Cutting hazards from sharp or worn blades

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000959gb_FM10.fm

15

Walk-Behind Trowels Safety Information

1.3 Operating Safety

Operator training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ Have received instruction on how to properly use the machine

■ Are familiar with required safety devices

The machine must not be accessed or operated by:

■ Children

■ People impaired by alcohol, drugs, or prescription drugs

Application area

Be aware of the application area.

■ Keep unauthorized personnel, children, and pets away from the machine.

■ Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

■ Identify whether special hazards exist in the application area, such as toxic

gases or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

■ Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Dust precaution

Dust created by construction activities may cause silicosis or respiratory harm. To

reduce the risk of exposure:

■ Work in a well ventilated area.

■ Use a dust control system.

■ Wear an approved dust/particle respirator.

wc_si000959gb_FM10.fm

16

Safety Information Walk-Behind Trowels

Safety devices, controls, and attachments

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

■ The machine is clean.

■ The machine’s labels are legible.

To ensure safe operation of the machine:

■ Do not operate the machine if any safety devices or guards are missing or

inoperative.

■ Do not modify or defeat the safety devices.

■ Only use accessories or attachments that are approved by Wacker Neuson.

Safe operating practices

When operating this machine:

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Do not operate a machine in need of repair.

■ Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic oil,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

General operating safety

■ Do not operate the machine with the beltguard missing. Exposed drive

belt and pulleys create potentially dangerous hazards that can cause

serious injuries.

■ Never operate this machine in applications for which it is not intended.

■ Do not use the trowel around pop-ups in the concrete that are lower than

the lowest ring on the ring guard.

■ Do not use a mobile device while operating this machine.

■ Do not tip the machine for cleaning or for any other reason.

■ Do not operate the trowel with the engine control module (safety interlock)

disabled. Serious injury could occur if struck by rotating trowel due to disabling

this interlock.

wc_si000959gb_FM10.fm

17

Walk-Behind Trowels Safety Information

1.4 Service Safety

Service training

Before servicing or maintaining the machine:

■ Read and understand the instructions contained in all manuals delivered

with the machine.

■ Familiarize yourself with the location and proper use of all controls and

protective devices.

■ Only trained personnel shall troubleshoot or repair problems occurring with

the machine.

■ Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

■ Do not allow untrained or improperly trained people to service or maintain

the machine. Personnel servicing or maintaining the machine must be

familiar with the associated potential risks and hazards.

Precautions

When servicing or maintaining the machine:

■ Read and understand the service procedures before performing any service

to the machine.

■ All adjustments and repairs must be completed before operating the

machine. Do not operate the machine with a known problem or deficiency.

■ All repairs and adjustments shall be completed by a qualified technician.

■ Turn off the machine before performing maintenance or making repairs.

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Reinstall the safety devices and guards after repair and maintenance

procedures are complete.

Machine modifications

When servicing or maintaining the machine:

■ Use only accessories/attachments that are approved by Wacker Neuson.

■ Do not defeat safety devices.

■ Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing parts and labels

■ Replace worn or damaged components.

■ Replace all missing and hard-to-read labels.

■ When replacing electrical components, use components that are identical in

rating and performance to the original components.

■ When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all

types of specifications, such as physical dimensions, type, strength, and

material.

wc_si000959gb_FM10.fm

18

Safety Information Walk-Behind Trowels

Cleaning

When cleaning and servicing the machine:

■ Keep machine clean and free of debris such as leaves, paper, cartons, etc.

■ Keep labels legible.

When cleaning the machine:

■ Do not clean the machine while it is running.

■ Never use gasoline or other types of fuels or flammable solvents to clean

the machine. Fumes from fuels and solvents can become explosive.

Personal protective equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

In addition, before servicing or maintaining the machine:

■ Tie back long hair.

■ Remove all jewelry (including rings).

Safe service practices

■ Do not crank a flooded engine with the spark plug removed on gasoline-

powered engines. Fuel trapped in the cylinder will squirt out the spark plug

opening.

■ Do not test for spark on gasoline-powered engines if the engine is flooded or

the smell of gasoline is present. A stray spark could ignite the fumes.

■ Disconnect the spark plug on machines equipped with gasoline engines,

before servicing, to avoid accidental start-up.

■ Do not remove blades while the machine is hanging overhead.

■ Only change the blades when the machine is supported securely.

■ Handle blades carefully. The blades can develop sharp edges which can

cause serious cuts.

After use

■ Stop the engine when the machine is not being operated.

■ Close the fuel valve on engines equipped with one when the machine is not

being operated.

■ Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

■ Store the machine properly when it is not being used. The machine should

be stored in a clean location out of the reach of children.

wc_si000959gb_FM10.fm

19

Walk-Behind Trowels Safety Information

1.5 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

■ Keep the area around the exhaust pipe free of flammable materials.

■ Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

■ Do not smoke while operating the machine.

■ Do not run the engine near sparks or open flames.

■ Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

■ Do not operate a machine when its fuel cap is loose or missing.

■ Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

■ Do not use the machine in areas with risk of explosion or fire.

Refueling safety

When refueling the engine:

■ Clean up any spilled fuel immediately.

■ Refill the fuel tank in a well-ventilated area.

■ Reinstall the fuel tank cap after refueling.

■ Use suitable tools for refueling (for example, a fuel hose or funnel).

■ Do not smoke.

■ Do not refuel a hot or running engine.

■ Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

► Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

► NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through items such as exhaust fans or hoses.

wc_si000960gb_FM10.fm

20

Labels Walk-Behind Trowels

2 Labels

2.1 Label Locations

wc_gr010351

J

C

H

G

D

F

L

B

E

A

M

K

N

O

P

La page charge ...

Wacker Neuson CT36-8A Manuel utilisateur

Wacker Neuson CT36-8A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents