Blastrac BDC-23 Le manuel du propriétaire

Catégorie
Aspirateurs
Taper
Le manuel du propriétaire

Ce manuel convient également à

BDC-23-230V-P
BDC-23-110V-P
C370 US-F-E
05/2018
US
F
E
INSTRUCTIONS MANUAL
MANUEL D’INSTRUCTIONS
MANUAL DE INSTRUCCIONES
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
1/16
I
US
Table of contents
Instructions for use .........................................................................................................2
Operator’s safety ............................................................................................................................. 2
General information for using the vacuum cleaner .......................................................................... 2
Proper uses ..................................................................................................................................... 2
Improper Use ................................................................................................................................... 3
Versions and variations ................................................................................................................... 3
General recommendations .............................................................................................................. 3
Vacuum cleaner description...........................................................................................4
Vacuum Cleaner Parts and Labels .................................................................................................. 4
Optional kits ..................................................................................................................................... 4
Accessories ..................................................................................................................................... 4
Packing and unpacking ................................................................................................................... 4
Unpacking, moving, use and storage .............................................................................................. 5
Setting to work - connection to the power supply ............................................................................ 5
Extensions ....................................................................................................................................... 5
Wet and dry applications ................................................................................................................. 6
Maintenance and repairs ................................................................................................................. 6
Technical specications ................................................................................................................... 7
Controls and indicators .................................................................................................................... 8
Inspections prior to starting ............................................................................................................. 8
Starting and stopping ...................................................................................................................... 8
Vacuum cleaner operation ............................................................................................................... 8
Primary lter shaker ........................................................................................................................ 8
Emergency stopping ........................................................................................................................ 8
Emptying the dust container ............................................................................................................ 8
Liquids vacuuming ........................................................................................................................... 8
At the end of a cleaning session ..................................................................................................... 9
Maintenance, cleaning and decontamination .................................................................................. 9
Primary and absolute lter disassembly and replacement .............................................................. 9
Primary lter replacement ............................................................................................................... 9
Absolute lter assembly or replacement ....................................................................................... 10
Tightness inspection ...................................................................................................................... 10
Wiring diagrams ............................................................................................................................ 10
Procedure for Longopac
®
system installation .................................................................................11
Procedure for hose removal .......................................................................................................... 13
Recommended spare parts ..........................................................................................14
Troubleshooting ............................................................................................................15
Translation of original instructions
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
2/16
I
US
Instructions for use
General information for using the
vacuum cleaner
Use the vacuum cleaner in accordance with the laws in force
in the country where it is used.
Besides the operating instructions and the laws in force in
the country where the vacuum cleaner is used, the technical
regulations for ensuring safe and correct operation must
also be observed (Legislation concerning environmental and
labour safety, i.e. European Union Directive 89/391/EC and
successive Directives).
Do not perform any operation that could jeopardize the safety
of people, property and the environment.
Comply with the safety indications and prescriptions in this
instruction manual.
Proper uses
This vacuum cleaner is suitable for commercial use, in hotels,
schools, hospitals, factories, shops, oces and apartment
hotels for example, for hire and in any case for purposes
other than normal domestic use.
This vacuum cleaner is suitable for cleaning and vacuuming
solid materials in indoor and outdoor environments.
Always leave enough room around the vacuum cleaner to
reach the controls easily.
The vacuum cleaner has been designed to be used by one
operator only.
This vacuum cleaner consists of an automated vacuum unit,
with a lter upstream and a container for collecting the
vacuumed material.
Read the operating instructions and comply with the important safety
recommendations identied by the word WARNING!
Operator’s safety
WARNING!
Before starting the vacuum cleaner, it
is absolutely essential to read these
operating instructions and to keep them
on hand for consultation.
The vacuum cleaner can only be used by people
who are familiar with the way it works and who
have been explicitly authorised and trained for the
purpose.
Before using the vacuum cleaner, the operators
must be informed, instructed and trained on how
to work it and for which substances its usage is
permitted including the safe method for removing
and disposing of the vacuumed material.
WARNING!
The use of vacuum cleaner by people (including
children) with limited physical and mental
capacities or lacking in experience and knowledge
is strictly forbidden, unless they are supervised by
a person who is experienced in the use and safe
handling of the machine.
Children must be supervised to make sure they will
not play with the vacuum cleaner.
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
3/16
I
US
Improper Use
WARNING!
The following use of the vacuum cleaner is strictly
forbidden:
Outdoors in case of atmospheric precipitation.
When not placed on horizontal levelled
grounds.
When the ltering unit is not installed.
When the vacuum inlet and/or hose are turned
to parts of the human body.
Use without the cover on the vacuum unit.
When the dust bag is not installed.
Use without the guards, protective covers and
safety systems installed by the manufacturer.
When the cooling vents are partially or totally
clogged.
When the vacuum cleaner is covered with
plastic or fabric sheets.
Use with the air outlet partially or totally
closed.
When used in narrow areas where there is no
fresh air.
Vacuuming liquids with vacuum cleaners
not equipped with specic original stopping
systems.
Vacuuming the following materials:
1. Burning materials (embers, hot ashes, lit
cigarettes, etc.).
2. Naked ames.
3. Combustible gas.
4. Flammable liquids, aggressive fuels
(gasoline, solvents, acids, alkaline
solutions, etc.).
5. Explosive dust/substances and/or ones
liable to ignite in a spontaneous way (such
as magnesium or aluminium dusts, etc.).
IMPORTANT: Fraudulent use is not admitted.
General recommendations
WARNING!
If an emergency situation occurs:
lter breakage
re outbreak
short-circuit
motor block
electric shock
etc.
Turn the vacuum cleaner o, unplug it and request
assistance from qualied personnel.
WARNING!
The vacuum cleaners must not be used or stored
outdoors, or in damp places.
Only versions with the level sensor can be used for
liquids, if not, they can only be used to vacuum dry
materials.
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
4/16
I
US
Vacuum cleaner description
Optional kits
Please contact the manufacturer’s sales network for
information on optionals.
Instructions for installing the optional are included in the
conversion kit.
WARNING!
Use only supplied and authorized genuine spare
parts.
Accessories
Various accessories are available; refer to the manufacturer’s
accessory catalogue.
WARNING!
Use only genuine accessories supplied and
authorized by the manufacturer.
Packing and unpacking
Dispose of the packing materials in compliance with the laws
in force.
Figure 2
Model
BDC-23-230V-P
BDC-23-110V-P
A (mm) 700
B (mm) 860
C (mm) 1750
Weight with packing
(kg)
86
Vacuum Cleaner Parts and Labels
Figure 1
1. Identication plate which includes:
Code of the Model, Technical Specications (see table
on page 7), Serial No., EC Mark, Year of manufacture,
Nominal network voltage.
2. Longopac System
3. Inlet
4. Outlet
5. Attention plate
Draws the operator’s attention to the fact that the lter
must only be shaken when the vacuum cleaner is turned
o (see also par. “Primary lter shaker”).
6. Plug for connecting the vacuum cleaner to an electrical
socket.
7. Silica Dust Warning
Draws the operator’s attention to the fact that exposure
of a crystalline silicon ust can cause cancer or silicosis.
This vacuum cleaner creates a strong air ow which is drawn
in through the inlet (4 - Fig. 1) and blown out through the
outlet (5 - Fig. 1).
Before turning on the vacuum cleaner, t the vacuum hose
into the inlet and then t the required tool on to the end part
(refer to the manufacturer’s accessory catalogue or Service
Centre).
The diameters of the authorised hoses are given in the
technical specications table.
The vacuum cleaner is equipped with a primary lter which
enables it to be used for the majority of applications.
Besides the primary lter, which retains the most common
types of dust, the vacuum cleaner can be tted with a
secondary lter (absolute H class) with a higher ltering
capacity for ne dusts and dusts that are hazardous to
health.
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
5/16
I
US
Unpacking, moving, use and storage
Operate on at, horizontal surfaces.
The load-bearing capacity of the surface the vacuum cleaner
is placed on must be suitable for bearing its weight).
Setting to work - connection to the
power supply
WARNING!
Make sure there is no evident sign of damage
to the vacuum cleaner before starting work.
Before plugging the vacuum cleaner into the
electrical mains, make sure the voltage rating
indicated on the data plate corresponds to that
of the electrical mains.
Plug the vacuum cleaner into a socket with a
correctly installed ground contact/connection.
Make sure that the vacuum cleaner is turned
o.
The plugs and connectors of the connection
cables must be protected against splashes of
water.
Make sure that connections to the electrical
mains and plug are correct.
Use the vacuum cleaners only when the cables
that connect to the electrical mains are in
perfect condition (damaged cables could lead
to electric shocks!).
Regularly check there are no signs of damage,
excessive wear, cracks or ageing on the
electric cable.
WARNING!
When the vacuum cleaner is operating, do not:
Crush, pull, damage or tread on the cable that
connects to the electrical mains.
Only disconnect the cable from the electrical
mains by removing the plug (do not pull the
cable).
Only replace the electric power cable with one
of the same type as the original: H07 RN - F.
The same rule applies if an extension is used.
The cable must be replaced by the
manufacturer’s Service Centre sta or by
equivalent qualied personnel.
Extensions
If an extension cable is used, make sure it is suitable for the
power input and protection degree of the vacuum cleaner.
Minimum section of extension cables: 2.5 mm
2
Maximum length = 20 m
Cable = H07 RN - F
WARNING!
Sockets, plugs, connectors and installation of the
extension cable must maintain the IP protection
degree of the vacuum cleaner, as indicated on the
data plate.
WARNING!
Never spray water on the vacuum cleaner: this
could be dangerous for persons exposed and could
short circuit the power supply.
WARNING!
The vacuum cleaner’s power socket must be
protected by a dierential circuit-breaker with
surge current limitation, that shuts o the power
supply when the current discharged to the ground
exceeds 30 mA for 30 msec. or an equivalent
protection circuit.
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
6/16
I
US
Wet and dry applications
[ NOTE ]
The supplied lters and the bag (if applicable) must be
installed correctly.
WARNING!
Comply with the safety regulations governing the
materials for which the vacuum cleaner is used.
WARNING!
If the version for liquids is used:
Make sure the liquid level sensor is working
correctly before vacuuming liquids.
If foam forms, turn o the vacuum cleaner
immediately and empty the container.
Warning: Switch o the vacuum cleaner
immediately if foam or liquid leaks out.
Regularly clean the liquid level limiting device
and check to make sure that there are no signs
of damage.
Warning: Dirty liquid vacuumed up by
the vacuum cleaner must be considered
conductive.
WARNING!
Vacuum cleaner for liquids.
When vacuuming a mix of water and air, take care
to avoid overloading the motor of the vacuum unit.
Maintenance and repairs
WARNING!
Disconnect the vacuum cleaner from its power
source before cleaning, servicing, replacing parts or
converting it to another version/variant, the plug
must be disconnected from the socket.
Carry out only the maintenance operations
described in this manual.
Use only original spare parts.
Do not modify the vacuum cleaner in any way.
Failure to comply with these instructions could
jeopardize your safety.
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
7/16
I
US
Technical specications
Parameter Units
BDC-23-230V-P
BDC-23-110V-P
120 230
Voltage (60 Hz) V 120 230
Power supply type Number of phases 1
Maximum power kW 2.4 3
Nominal current input A 15.8 13
Max vacuum Inches H
2
O 71.5 84.7
Max air ow rate cfm 270 286
Noise level, @ 3’3" (1 m) dB(A) - vacuum unit 75
Protection IP 43
Insulation Class I
Inlet (diameter) in. 3
Hoses allowed (diameter) in. 2 / 3
Container capacity gal 26.4
Filter surface Sq. ft 21
Absolute lter surface Sq. ft 25.9
HEPA absolute lter eciency MPPS 99,995% @ 0.18 micron
Cable length ft 30
Weight
(1)
lbs. 157
(1) Net weight
(2) hPa = mbar
Storage conditions:
T : -10°C ÷ +40°C
Humidity: 85%
T : -10°C ÷ +40°C
Operating conditions:
Maximum altitude: 800 m
(Up to 2,000 m with reduced performances)
Humidity: 85%
Dimensions
(Fig. 3)
BDC-23-230V-P
BDC-23-110V-P
A B C
in 31.3 23.6 61.8
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
8/16
I
US
Primary lter shaker
Depending on the quantity of dust cleaned up, shake the
main lter by means of the knob “3” (Fig. 4).
WARNING!
Stop the vacuum cleaner before using the lter
shaker.
Do not shake the lter while the vacuum cleaner is
on, as this could damage the lter.
Wait before restarting the vacuum cleaner, to allow the dust
to settle.
Emergency stopping
Turn the switch “1” (Fig. 4) to “0” position.
Emptying the dust container
WARNING!
Before proceeding with these operations, turn
the vacuum cleaner o and disconnect the plug
from the power socket.
Check the class of the vacuum cleaner.
Before emptying the container it is advisable to clean the
lter (see “Primary lter shaker”).
Standard version is not suitable for vacuuming
hazardous dust
Release the dust container (2 , Fig. 1) using lever
(3, Fig. 1), then remove and empty it.
Make sure the seal is in perfect condition and
correctly positioned.
Place the container back in position and secure it
again.
Liquids vacuuming
WARNING!
Check that the vacuum cleaner is equipped with
liquids mechanical stop.
The lter element will be wet after liquids have been
vacuumed.
A wet lter element can quickly become clogged if the
vacuum cleaner is then used to vacuum dry substances.
For this reason, make sure that the lter element is dry
or replace it with another one before using the vacuum
cleaner for dry materials.
Controls and indicators
Figure 4
1. Motor start/stop switch
2. Power indicator
3. Manual lter shaker knob
Figure 5
1. Inlet
Inspections prior to starting
Prior to starting, check that:
the lters are installed;
all the levers are locked in place;
the vacuum hose and tools have been correctly tted to
the inlet (1 - Fig. 5);
WARNING!
Do not use the vacuum cleaner if the lter is faulty.
Starting and stopping
Figure 4
WARNING!
Lock the castor brakes before starting the vacuum
cleaner.
Turn the switch “1” (Fig. 4) to “I” position to start the
vacuum cleaner.
Turn the switch to “0” position to turn the vacuum
cleaner o.
Vacuum cleaner operation
WARNING!
The air speed in the suction tube must not be less
than 20 m/s.
WARNING!
Consult the “Troubleshooting” chapter if faults
occur.
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
9/16
I
US
At the end of a cleaning session
Turn the vacuum cleaner o with switch (1 - Fig. 4) and
disconnect the plug from the socket.
Wind the connection cable up and hang it in the
relevant compartment (Fig. 6).
Empty the container as described in the “Emptying the
container” paragraph.
Clean the vacuum cleaner as described in the paragraph
“Maintenance, cleaning and decontamination”.
Wash the container with clean water if aggressive
substances have been vacuumed.
Store the vacuum cleaner in a dry place, out of reach of
unauthorised persons.
Maintenance, cleaning and
decontamination
WARNING!
To guarantee the safety level of the vacuum
cleaner, only original spare parts supplied by the
manufacturer should be used.
WARNING!
The precautions described below must be taken
during all maintenance operations, including
cleaning and replacing the primary and absolute
lters.
WARNING!
The maintenance, cleaning and decontamination
operations must only be performed with
the vacuum cleaner turned o and the plug
disconnected from the power socket.
It is absolutely forbidden to perform maintenance
with the plug connected to the socket.
Danger of electric shock!
If the user is performing the maintenance operations,
the vacuum cleaner must be disassembled, cleaned
and overhauled as far as reasonably possible without
hazards for the maintenance personnel or other people.
The suitable precautions include decontamination before
disassembling the vacuum cleaner, adequate ltered
ventilation of the exhaust air from the room in which
it is disassembled, cleaning the maintenance area and
suitable personal protection.
A check must be carried out by the manufacturer or
the personnel of the same at least once a year. For
example: check the air lters to nd out whether the
air-tightness of the vacuum cleaner has been impaired
in any way and make sure the electric system operates
correctly.
Primary and absolute lter
disassembly and replacement
WARNING!
When the vacuum cleaner is used to vacuum
hazardous substances, the lters become
contaminated, therefore:
work with care and avoid spilling the vacuumed
dust and/or material;
place the disassembled and/or replaced lter
in a sealed plastic bag;
close the bag hermetically;
dispose of the lter in accordance with the
laws in force.
WARNING!
Filter replacement is a serious matter. The
lter must be replaced with one of identical
characteristics, ltering surface and category.
Otherwise the vacuum cleaner will not operate
correctly.
Primary lter replacement
Figure 7
Before proceeding with these operations, turn o the vacuum
cleaner and remove the plug from the power socket.
Release the stop (1), unscrew the lter shaker knob
(2).
Release the closing band (3).
Lift the motor head (4).
Lift lter (5) and unscrew the lter clamp (6) on
bearing ring (7).
Unscrew cage (8) and overturn the lter, exposing
coupling clamp (9).
Release the clamps and detach the cage from the lter.
Dispose of the lter according to the laws in force.
Fit the new lter and secure it in the cage with special
clamps. Assemble the components in the reverse order
of disassembly.
WARNING!
Take care not to raise dust when this operation is
carried out. Wear a P3 mask and other protective
clothing plus protective gloves (DPI) suited to the
hazardous nature of the dust collected, refer to the
laws in force.
WARNING!
Reassemble with care to avoid trapping your hands
between the vacuum unit and the container. Use
gloves that provide protection against mechanical
risks (EN 388) with a level of protection CAT. II.
If necessary contact the manufacturer’s Service Centre.
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
10/16
I
US
Absolute lter assembly or
replacement
WARNING!
Do not use the absolute lter again after having
removed it from the vacuum cleaner.
Figure 8
1. Vacuuming unit
2. Closing band
3. Filter shaker stop
4. Filter shaker knob
5. Washer
6. Ferrule
7. Absolute lter
8. Seal
9. Disc
10. Nut
WARNING!
Reassemble with care to avoid trapping your hands
between the vacuum unit and the container. Use
gloves that provide protection against mechanical
risks (EN 388) with a level of protection CAT. II.
Before proceeding with these operations, turn the vacuum
cleaner o and disconnect the plug from the power socket.
Assembly
1. Release the stop (3) and unscrew the lter shaker knob
(4), release the closing band (2) and remove the head
(1).
2. Unscrew the nut from the ferrule under the head (1),
insert the washer (5), screw the ferrule (6), insert the
lter (7), the gasket (8) and the disc (9), screw the
nut (10), t the head back in position and x with the
closing band (2), screw the knob (4) and lock it with
the stop (3).
Replacement
1. Proceed as indicated in step 1 of the assembling
procedure.
2. Unscrew the nut (10), remove the disc (9) and the
gasket (8).
3. Replace the lter (7) and proceed in the reverse order
to reassemble the head.
To dispose of the lter put it in a sealed plastic bag, close it
hermetically and dispose of it in accordance with the laws in
force.
Tightness inspection
Hoses check
Figure 9
Make sure the connecting hoses (1) are in a good condition
and correctly xed.
If the hoses are damaged, broken or badly connected to the
unions, they must be replaced.
When sticky materials are treated, check for possible
clogging along the hose, in the inlet and on the bae plate
inside the ltering chamber.
Scrape inlet (2) from the outside and remove the deposited
waste as indicated in the gure.
Wiring diagrams
Figure 10
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
11/16
I
US
Procedure for Longopac
®
system installation
2. Insert the Longopac
®
bag and cut the connections
3. Prepare the bag on the stand, pull out the end and start
1. Remove the holder
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
12/16
I
US
4. Place the holder on the vacuum cleaner
5. “Duck-neck” closure of the bag with adhesive tape
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
13/16
I
US
Procedure for hose removal
2. Place the vacuum
plug
1. Remove the hose,
including its coupling,
from the vacuum
cleaner
3. Roll the hose 4. Thread the two ends
into each other
5. Use a belt or tape to
transport and store
away from dust
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
14/16
I
US
Recommended spare parts
The following is a list of spare parts that should be kept ready at hand in order to speed up maintenance operations.
Refer to the manufacturer’s spare parts catalogue when ordering spare parts.
Description Code
Star lter kit 40000699
Filter ring seal Z8 17026
Filter chamber gasket 40000762
Filter clamp Z8 18079
Absolute lter Z8 17455
230V 1000W Motor 40000937
110V 1000W Motor 40000938
Brushes (carbon) for 230V 1000W motors (2 brushes) 40000885
Brushes (carbon) for 120V 1000W motors (2 brushes) 40000886
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
15/16
I
US
Troubleshooting
Problem Cause Remedy
The vacuum cleaner does not
start
Lack of power supply Check for power at the socket.
Check the condition of the socket and the
cable.
Ask for assistance to be performed by a
qualied manufacturer’s technician.
The vacuum cleaner revolutions
increase
Clogged primary lter Use the lter shaker. Replace it if this is not
sucient.
Clogged vacuum hose Check the vacuum hose and clean it.
Dust leaks from the vacuum
cleaner
The lter is torn Replace it with another of identical type.
Inadequate lter Replace it with another of a suitable category
and check.
Noisy motors Motor brushes (carbon) worn or
broken
Remove and replace the (carbon) motor
brushes.
Electrostatic current on the
vacuum cleaner
Non existent or inecient
grounding
Check all ground connections. In particular on
the vacuum inlet tting; replace the hose with
an antistatic hose.
www.blastrac.com ‒ [email protected]
Instruction manual BDC-23-230V-P_ BDC-23-110V-P
16/16
I
US
www.blastrac.com ‒ [email protected]
1/16
Manuel d’instructions BDC-23-230V-P_ BDC-23-110V-P
I
F
Index
Mode d’emploi .................................................................................................................2
Sécurité de l’opérateur .................................................................................................................... 2
Informations générales sur l’utilisation de l’aspirateur ..................................................................... 2
Utilisations prévues ......................................................................................................................... 2
Utilisations inappropriées ................................................................................................................ 3
Versions et variantes de construction .............................................................................................. 3
Recommandations générales .......................................................................................................... 3
Description de l’aspirateur .............................................................................................4
Composants de l’Aspirateur et étiquettes ........................................................................................ 4
Options de transformation ............................................................................................................... 4
Accessoires ..................................................................................................................................... 4
Emballage et déballage ................................................................................................................... 4
Déballage, manutention, emploi et stockage .................................................................................. 5
Mise en service - raccordement au réseau d’alimentation électrique ............................................. 5
Rallonges ........................................................................................................................................ 5
Aspiration de substances sèches - aspiration de liquides ............................................................... 6
Entretien et réparation ..................................................................................................................... 6
Caractéristiques techniques ............................................................................................................ 7
Dimensions ...................................................................................................................................... 7
Commandes et indicateurs .............................................................................................................. 8
Contrôles avant la mise en marche ................................................................................................. 8
Mise en marche et arrêt .................................................................................................................. 8
Fonctionnement ............................................................................................................................... 8
Secoueur primaire ........................................................................................................................... 8
Arrêt d’urgence ................................................................................................................................ 8
Vidange de la cuve à poussières .................................................................................................... 8
Aspiration de liquides ...................................................................................................................... 8
En n de poste ................................................................................................................................ 9
Entretien, nettoyage et décontamination ......................................................................................... 9
Démontage et remplacement des ltres primaire et absolu ............................................................ 9
Remplacement du ltre primaire ..................................................................................................... 9
Montage ou remplacement du ltre absolu ................................................................................... 10
Contrôle des étanchéités ............................................................................................................... 10
Schémas électriques ..................................................................................................................... 10
Procédure pour l’installation du système Longopac ....................................................................... 11
Procédure de retrait du tuyau ........................................................................................................ 13
Pièces détachées conseillées ......................................................................................14
Recherche des pannes .................................................................................................15
Traduction des instructions originales
www.blastrac.com ‒ [email protected]
Manuel d’instructions BDC-23-230V-P_ BDC-23-110V-P
2/16
I
F
Mode d’emploi
Informations générales sur
l’utilisation de l’aspirateur
L’utilisation de l’aspirateur est soumise aux normes
internationales en vigueur.
En plus des instructions du mode d’emploi et des règlements
en vigueur dans le Pays où il est utilisé, pour la prévention
des accidents il est nécessaire d’observer les règles
techniques pour un travail sûr et correct (Législation relative
à la sécurité sur le lieu de travail, Directive Communautaire
89 / 391 / CE et suivant).
Eviter tout travail pouvant porter atteinte à la sécurité des
personnes, des choses et de l’environnement.
Observer les informations et les prescriptions de sécurité
contenues dans ce manuel d’instructions.
Utilisations prévues
Cet aspirateur convient pour l’emploi commercial, par
exemple dans des hôtels, des écoles, des hôpitaux, des
usines, des magasins, des bureaux, des résidences, pour
l’emploi en location et de toute manière pour des emplois
diérents du simple usage domestique.
Cet aspirateur convient pour les travaux de nettoyage et
de collecte de matières solides en lieux couverts et à ciel
ouvert.
Prévoir toujours un espace libre autour de l’aspirateur
pour permettre un accès aisé aux commandes.
La machine a été conçue pour être utilisée par un seul
opérateur.
Cet aspirateur est formé d’une unité d’aspiration motorisée,
précédée d’une unité ltrante et munie d’une cuve pour la
collecte de la matière aspirée.
Lire les instructions du mode d’emploi et observer les avertissements importants de
sécurité repérés par ATTENTION !
Sécurité de l’opérateur
ATTENTION !
Avant de mettre l’aspirateur en service,
lire absolument les instructions
d’utilisation et les garder à portée de
main pour pouvoir les consulter en cas de
besoin.
L’utilisation de l’aspirateur est réservée
exclusivement au personnel expérimenté, formé et
expressément chargé du fonctionnement.
Avant l’utilisation, les opérateurs doivent être
instruits et formés à l’utilisation de l’aspirateur
et des substances pour lesquelles il doit être
utilisé, y compris la méthode sûre d’évacuation et
d’élimination de la matière recueillie.
ATTENTION !
Cet aspirateur ne doit pas être utilisé par des
personnes (y compris des enfants) présentant des
troubles psychiques, sensoriels ou mentaux ou
ayant un degré d’instruction et de connaissance
insusant, à moins qu’ils soient toujours
surveillées par des personnes compétentes ou
qu’ils aient reçu d’elles les instructions d’utilisation
de l’aspirateur.
Les enfants doivent être surveillés an qu’ils ne
jouent pas avec l’aspirateur.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

Blastrac BDC-23 Le manuel du propriétaire

Catégorie
Aspirateurs
Taper
Le manuel du propriétaire
Ce manuel convient également à