Blastrac BDC-24 Le manuel du propriétaire

BDC-24-230V-P

C406 US-F-E

05/2018

US

F

E

INSTRUCTIONS MANUAL

MANUEL D’INSTRUCTIONS

MANUAL DE INSTRUCCIONES

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

1/16

I

US

Table of contents

Instructions for use ........................................................................... 2

Operator’s safety ............................................................................................ 2

General information for using the vacuum cleaner ............................................... 2

Proper uses .................................................................................................... 2

Improper Use ................................................................................................. 2

General recommendations ................................................................................ 3

Vacuum cleaner description .............................................................. 4

Vacuum Cleaner Parts and Labels ...................................................................... 4

Optional kits ................................................................................................... 4

Accessories .................................................................................................... 4

Packing and unpacking .................................................................................... 4

Unpacking, moving, use and storage ................................................................. 4

Setting to work - connection to the power supply ................................................ 5

Extensions ..................................................................................................... 5

Dry applications .............................................................................................. 5

Maintenance and repairs .................................................................................. 5

Technical data (US) ......................................................................................... 6

Controls and indicators .................................................................................... 7

Inspections prior to starting ............................................................................. 7

Starting and stopping ...................................................................................... 7

Vacuum cleaner operation ................................................................................ 8

Primary cartridge lters operation ..................................................................... 8

Emergency stopping ........................................................................................ 8

Emptying the dust container ............................................................................. 8

Plastic bag ..................................................................................................... 9

How to change the bag .................................................................................... 9

Tilting discharge device replacement and use ...................................................... 9

Compressor use and maintenance ..................................................................... 9

At the end of a cleaning session ........................................................................ 9

Maintenance, cleaning and decontamination ....................................................... 9

Cartridge and absolute lter disassembly and replacement ..................................10

Filter cartridge replacement .............................................................................10

HEPA lter replacement ..................................................................................10

Tightness inspection .......................................................................................11

Disposing of the vacuum cleaner ......................................................................11

Wiring diagram list .........................................................................................11

Procedure for Longopac

®

system installation ......................................................12

Procedure for hose removal .............................................................................14

Recommended spare parts .............................................................. 15

Troubleshooting .............................................................................. 16

Translation of the original instructions

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

2/16

I

US

Instructions for use

Proper uses

This vacuum cleaner is suitable for commercial use, in

hotels, schools, hospitals, factories, shops, oces and

apartment hotels for example, for hire and in any case for

purposes other than normal domestic use.

This vacuum cleaner is suitable for cleaning and vacuuming

solid materials in indoor and outdoor environments.

■ Always leave enough room around the vacuum cleaner

to reach the controls easily.

The vacuum cleaner has been designed to be used by one

operator only.

This vacuum cleaner consists of an automated vacuum unit,

with a lter upstream and a container for collecting the

vacuumed material.

Improper Use

WARNING!

The following use of the vacuum cleaner is strictly

forbidden:

■ Outdoors in case of atmospheric precipitation.

■ When not placed on horizontal levelled

grounds.

■ When the ltering unit is not installed.

■ When the vacuum inlet and/or hose are turned

to parts of the human body.

■ Use without the cover on the vacuum unit.

■ When the dust bag is not installed.

■ Use without the guards, protective covers and

safety systems installed by the manufacturer.

■ When the cooling vents are partially or totally

clogged.

■ When the vacuum cleaner is covered with

plastic or fabric sheets.

■ Use with the air outlet partially or totally

closed.

■ When used in narrow areas where there is no

fresh air.

■ Vacuuming liquids with vacuum cleaners

not equipped with specic original stopping

systems.

■ Vacuuming the following materials:

1. Burning materials (embers, hot ashes, lit

cigarettes, etc.).

2. Naked ames.

3. Combustible gas.

4. Flammable liquids, aggressive fuels

(gasoline, solvents, acids, alkaline solutions,

etc.).

5. Explosive dust/substances and/or ones

liable to ignite in a spontaneous way (such as

magnesium or aluminium dusts, etc.).

IMPORTANT: Fraudulent use is not admitted.

Read the operating instructions and comply with the important safety

recommendations identied by the word WARNING!

Operator’s safety

WARNING!

Before starting the vacuum cleaner, it

is absolutely essential to read these

operating instructions and to keep them

on hand for consultation.

The vacuum cleaner can only be used by people

who are familiar with the way it works and who

have been explicitly authorised and trained for the

purpose.

Before using the vacuum cleaner, the operators

must be informed, instructed and trained on how

to work it and for which substances its usage is

permitted including the safe method for removing

and disposing of the vacuumed material.

WARNING!

The use of vacuum cleaner by people (including

children) with limited physical and mental

capacities or lacking in experience and knowledge

is strictly forbidden, unless they are supervised by

a person who is experienced in the use and safe

handling of the machine.

Children must be supervised to make sure they will

not play with the vacuum cleaner.

General information for using the

vacuum cleaner

Use the vacuum cleaner in accordance with the laws in force

in the country where it is used.

Besides the operating instructions and the laws in force in

the country where the vacuum cleaner is used, the technical

regulations for ensuring safe and correct operation must also

be observed (EU and where applicable: legislation concerning

environmental and labour safety, i.e. European Union

Directive 89/391/EC and successive Directives).

Do not perform any operation that could jeopardize the

safety of people, property and the environment.

Comply with the safety indications and prescriptions in this

instruction manual.

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

3/16

I

US

General recommendations

WARNING!

If an emergency situation occurs:

■ lter breakage

■ re outbreak

■ short-circuit

■ motor block

■ electric shock

■ etc.

Turn the vacuum cleaner o, unplug it and request

assistance from qualied personnel.

WARNING!

The vacuum cleaners must not be used or stored

outdoors, or in damp places.

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

4/16

I

US

Vacuum cleaner description

Optional kits

Please contact the manufacturer’s sales network for

information on optionals.

Instructions for installing the optional are included in the

conversion kit.

WARNING!

Use only supplied and authorized genuine spare

parts.

Accessories

Various accessories are available; refer to the manufacturer’s

accessory catalogue.

WARNING!

Use only genuine accessories supplied and

authorized by the manufacturer.

Packing and unpacking

Dispose of the packing materials in compliance with the laws

in force.

Figure 2

Model BDC-24-230V-P

Units in

A 28

B 53

C 87

Weight with packing

(lbs.)

311

Unpacking, moving, use and storage

Operate on at, horizontal surfaces.

The load-bearing capacity of the surface the vacuum cleaner

is placed on must be suitable for bearing its weight).

Vacuum Cleaner Parts and Labels

Figure 1

1. Identication plate which includes:

Code of the Model, Technical Specications (see table

on page 6), Serial No., Year of manufacture, Nominal

network voltage.

2. Dust container

3. Dust container release lever

4. Inlet

5. Accessories compartment

6. Outlet

7. Plug for connecting the vacuum cleaner to an electrical

socket.

8. Silica Dust Warning

Draws the operator’s attention to the fact that exposure

of a crystalline silicon ust can cause cancer or silicosis.

This vacuum cleaner creates a strong air ow which is drawn

in through the inlet (4 - Fig. 1) and blown out through the

outlet (6 - Fig. 1).

Before turning on the vacuum cleaner, t the vacuum hose

into the inlet and then t the required tool on to the end part

(refer to the manufacturer’s accessory catalogue or Service

Centre).

The diameters of the authorised hoses are given in the

technical specications table.

The vacuum cleaner is equipped with cartridge lters which

enable it to be used for the majority of applications.

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

5/16

I

US

Setting to work - connection to the

power supply

WARNING!

■ Make sure there is no evident sign of damage

to the vacuum cleaner before starting work.

■ Before plugging the vacuum cleaner into the

electrical mains, make sure the voltage rating

indicated on the data plate corresponds to that

of the electrical mains.

■ Plug the vacuum cleaner into a socket with a

correctly installed ground contact/connection.

■ Make sure that the vacuum cleaner is turned

o.

■ The plugs and connectors of the connection

cables must be protected against splashes of

water.

■ Make sure that connections to the electrical

mains and plug are correct.

■ Use the vacuum cleaners only when the cables

that connect to the electrical mains are in

perfect condition (damaged cables could lead

to electric shocks!).

■ Regularly check there are no signs of damage,

excessive wear, cracks or ageing on the electric

cable.

WARNING!

When the vacuum cleaner is operating, do not:

■ Crush, pull, damage or tread on the cable that

connects to the electrical mains.

■ Only disconnect the cable from the electrical

mains by removing the plug (do not pull the

cable).

■ Only replace the electric power cable with one

of the same type as the original; the same rule

applies if an extension is used.

■ The cable must be replaced by the

manufacturer’s Service Centre sta or by

equivalent qualied personnel.

Extensions

▪ If an extension cable is used, make sure it is

suitable for the power input and protection degree of

the vacuum cleaner.

US version

Minimum section of extension cables: 12 AWG

Maximum length = 66 ft

Cable = SJT

WARNING!

Sockets, plugs, connectors and installation of the

extension cable must maintain the IP protection

degree of the vacuum cleaner, as indicated on the

data plate.

WARNING!

Never spray water on the vacuum cleaner: this

could be dangerous for persons exposed and could

short circuit the power supply.

WARNING!

The vacuum cleaner’s power socket must be

protected by a dierential circuit-breaker with

surge current limitation, that shuts o the power

supply when the current discharged to the

ground exceeds 30 mA for 30 ms or an equivalent

protection circuit.

Dry applications

[ NOTE ]

The supplied lters and the bag (if applicable) must be

installed correctly.

WARNING!

Comply with the safety regulations governing the

materials for which the vacuum cleaner is used.

Maintenance and repairs

WARNING!

Disconnect the vacuum cleaner from its power

source before cleaning, servicing, replacing parts

or converting it to another version/variant, the

plug must be disconnected from the socket and

controlled by the operator.

■ Carry out only the maintenance operations

described in this manual.

■ Use only original spare parts.

■ Do not modify the vacuum cleaner in any way.

Failure to comply with these instructions could

jeopardize your safety. Moreover, such action would

immediately make the EC declaration of conformity

issued with the vacuum cleaner void.

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

6/16

I

US

Technical data (US)

Parameter Units BDC-24-230V-P

Voltage (60 Hz) V 230

Power supply type Number of phases 1

Maximum power kW 4.5

Nominal current input A 19.5

Max vacuum Inches H

2

O 84.7

Max air ow rate cfm 286

Noise level, @ 3’3" (1 m)

dB(A) - vacuum unit 71

dB(A) - compressor 78

Protection IP 44

Insulation Class F

Inlet (diameter) in. 3

Hoses allowed (diameter) in. 2 / 3

Container capacity gal 26.4

Cartridge lter surface Sq. ft 161.5

Absolute lter surface Sq. ft 37.7

HEPA absolute lter eciency MPPS 99.995% @ 0.18 micron

Cable length ft 30

Weight

(1)

lbs. 289

(1) Net weight

(2) hPa = mbar

Storage conditions:

T : -10°C ÷ +40°C

Humidity: 85%

T : -10°C ÷ +40°C

Operating conditions:

Maximum altitude: 800 m

(Up to 2,000 m with reduced performances)

Humidity: 85%

Dimensions

Fig. 3

BDC-24-230V-P A B C

in 38.5 23.6 70

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

7/16

I

US

Controls and indicators

Figure 4

1. Main motor Start/Stop indicator and button

If the indicator is lit, the main motor is ON.

You can start/stop the main motor with this button.

2. Second motor Start/Stop indicator and button

If the indicator is lit, the second motor is ON.

You can start/stop the second motor with this button.

3. Third motor Start/Stop indicator and button

If the indicator is lit, the third motor is ON.

You can start/stop the third motor with this button.

4. Stop button

This button stops all the motors simultaneously when

pressed (but doesn’t turn the power of the vacuum

cleaner o).

5. Max. vacuumed level indicator

If lit, this indicates the maximum level of the vacuumed

material has been reached in the container, if the level

control for solids is installed.

6. Power indicator

Indicates the vacuum cleaner is powered.

7. Primary lter indicator

Green - Indicates the cartridge lters are functioning

properly.

Red - Indicates the cartridge lters are blocked.

8. Absolute lter indicator (if installed)

Red - Indicates the absolute lter is blocked.

Figure 5

1. Dust container release lever

2. Castor lever

3. Closing band lever

4. Electric power cable

5. Handle

6. Inlet

7. Electrical panel

Inspections prior to starting

Prior to starting, check that:

■ the lters are installed;

■ all the levers are locked in place;

■ the vacuum hose and tools have been correctly tted to

the inlet (6 - Fig. 5);

■ the bag is installed, if applicable.

WARNING!

Do not use the vacuum cleaner if the lter is faulty.

Starting and stopping

WARNING!

Before starting the vacuum cleaner, lock the castor

brakes (2 - Fig. 5) and turn the switch (7 - Fig. 5)

on “I” position.

WARNING!

Check the pressure of the air used to clean the

lters which is produced by the compressor.

It must never be superior than 5,5 bars, if

necessary, adjust it to the correct level using the

pressure releaf valve (8 - Fig. 5).

Figure 4

■ To turn on the vacuum cleaner, press the switches (2-

3-4).

When pressed, the motors start and the state of the

same is shown by indicators (2-3-4).

■ To turn o the vacuum cleaner, press the switches

again.

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

8/16

I

US

Primary cartridge lters operation

Figure 6

1. Electropneumatic device

2. Filter cartridges

3. Timer

The ltering cartridges (2) serve the purpose of ltering

the intake air. The vacuum cleaner is equipped with a fully

automatic electropneumatic device (1) to alternately clean

the ltering cartridges (2) which guarantees continuous

service; powered with a 24V rating, is complete with cyclic

timer (3) to regulate the following times:

T3= time between one cleaning cycle and the next, set on 0

seconds;

T2= time between one cleaning operation of the cartridge

(2) and the next, set on 20 seconds;

T1= opening time of the solenoid valve for backwashed air

exhaust into the cartridge, set at 1 tenths of a second.

The shorter the time, the more energetic the cleaning

action will be.

Factory setting should not be changed if without

consulting Blastrac.

The three solenoid valves of the electropneumatic device

control the cleaning of the relative lter cartridges.

Figure 6A

1. Filter cleaning solenoid valve E1

2. Filter cleaning solenoid valve E2

3. Filter cleaning solenoid valve E3

Emergency stopping

Press Stop button (5 - Fig. 4). The vacuum cleaner stops.

WARNING!

The motors and internal components of the vacuum

cleaner will still be electrically powered.

To start the vacuum cleaner, see the starting and stopping

paragraph

Emptying the dust container

WARNING!

■ Before proceeding with these operations, turn

the vacuum cleaner o and disconnect the plug

from the power socket.

■ Check the class of the vacuum cleaner.

■ Version not suitable for vacuuming hazardous dust

▪ Release dust container (1 - Fig. 7), with lever (2),

then remove and empty it.

▪ Make sure the seal is in perfect condition and

correctly positioned.

▪ Place the container back in position and secure it

again.

Vacuum cleaner operation

WARNING!

The air speed in the suction tube must not be less

than 20 m/s.

This state is shown by the green indicator of the

primary lter.

When using the vacuum cleaner, check:

■ The state of the max. vacuumed material level indicator

(6 - Fig. 4) if the level check is installed.

■ The state of the primary lter (8 - Fig. 4) and the

absolute lter (if installed) (9 - Fig. 4).

WARNING!

If one of the indicators is lit, follow the instructions.

Symbol

Indicator

signal

Indicator

colour

Vacuum cleaner

state and

procedure

bar/psi

MAX

Max. vacuumed

material level

(6 - Fig. 4)

Red

Suction stopped.

Empty the container

(see relevant

paragraph).

bar/psi

MAX

Primary lter

(8 - Fig. 4)

Red

Suction on.

Replace the cartridge

lters.

(see relevant

paragraph).

bar/psi

MAX

Absolute lter

(9 - Fig. 4)

Red

Suction on.

Change absolute lter

(see relevant

paragraph).

WARNING!

Consult the “Troubleshooting” chapter if faults

occur.

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

9/16

I

US

Plastic bag

You can use the plastic bags supplied by the manufacturer

sales network (Fig. 8).

How to change the bag

WARNING!

■ These operations can only be carried out by

trained and qualied personnel who must wear

adequate clothing, in compliance with the laws

in force.

■ Take care not to raise dust during these

operations. Wear a P3 protective mask.

■ In case of dangerous and/or toxic dust, you

must use the supplied safety bag for these

vacuum cleaners.

■ The bag must only be disposed of by qualied

personnel and in compliance with the laws in

force.

Tilting discharge device replacement

and use

Figure 8A

1. Tilting discharge device assembly

■ Fasten the hopper to the ltering chamber, by inserting

it into the relevant housings and, operating on the lever

(2) to lock it.

■ Insert the bag (Longopac

®

) into the relevant support

and fasten its end with the belt (3).

■ Engage the tilting discharge device support to the

hopper by fastening it with the relevant pins.

■ Remove the bag (Longopac

®

) until it lays on the lower

support platform and close its end with the supplied

clamp.

■ When the bag is full (Longopac

®

) close the upper end

with two clamps by fastening them at 50 mm one

from the other, then with a pair of scissors cut the bag

between the two clamps.

Compressor use and maintenance

WARNING!

Refer to the use and maintenance manual, supplied

with the machine documentation, when using or

servicing the compressor.

At the end of a cleaning session

■ Turn the vacuum cleaner o with switches (2-3-4 - Fig.

4), turn the electric panel (7 - Fig. 5) o and disconnect

the plug from the socket

■ Wind the connection cable up and hang it in the

relevant compartment (Fig. 9).

■ Empty the container as described in the “Emptying the

container” paragraph.

■ Clean the vacuum cleaner as described in the paragraph

“Maintenance, cleaning and decontamination”.

■ Wash the container with clean water if aggressive

substances have been vacuumed.

■ Store the vacuum cleaner in a dry place, out of reach of

unauthorised persons.

Maintenance, cleaning and

decontamination

WARNING!

To guarantee the safety level of the vacuum

cleaner, only original spare parts supplied by the

manufacturer should be used.

WARNING!

The precautions described below must be taken

during all the maintenance operations, including

cleaning and replacing of the main and HEPA lters.

WARNING!

The maintenance, cleaning and decontamination

operations must only be performed with the

vacuum cleaner turned o with switch (7 - Fig. 5)

and the plug disconnected from the power socket.

It is absolutely forbidden to perform maintenance

with the plug connected to the socket.

Danger of electric shock!

■ If the user is performing the maintenance operations,

the vacuum cleaner must be disassembled, cleaned

and overhauled as far as reasonably possible without

hazards for the maintenance personnel or other people.

The suitable precautions include decontamination before

disassembling the vacuum cleaner, adequate ltered

ventilation of the exhaust air from the room in which

it is disassembled, cleaning the maintenance area and

suitable personal protection.

■ A check must be carried out by the manufacturer or

the personnel of the same at least once a year. For

example: check the air lters to nd out whether the

air-tightness of the vacuum cleaner has been impaired

in any way and make sure the electric control panel

operates correctly.

WARNING!

The procedures for servicing and emptying the

vacuum cleaner including removing the dust

container, must only be performed by specialised

personnel wearing protective clothing. Do not use

without the complete lter system in place.

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

10/16

I

US

Cartridge and absolute lter

disassembly and replacement

WARNING!

When performing the lter replacement it is

necessary to:

■ work with care and avoid spilling the vacuumed

dust and/or material;

■ place the disassembled and/or replaced lter

in a sealed plastic bag;

■ close the bag hermetically;

■ dispose of the lter in accordance with the

laws in force.

WARNING!

Filter replacement is a serious matter. The

lter must be replaced with one of identical

characteristics, ltering surface and category.

Otherwise the vacuum cleaner will not operate

correctly.

WARNING!

Take care not to raise dust when this operation is

carried out. Wear a P3 mask and other protective

clothing plus protective gloves (DPI) suited to the

hazardous nature of the dust collected, refer to the

laws in force.

WARNING!

Reassemble with care to avoid trapping your hands

between the vacuum unit and the container. Use

gloves that provide protection against mechanical

risks (EN 388) with a level of protection CAT. II.

Filter cartridge replacement

Figure 11

1. Vacuuming unit

2. Locking lever

3. Ring

4. Compressed air hose

5. Electric cable

6. Locking lever

7. Cover

8. Filter cartridge support

9. Filter cartridge

10. Filter cartridge xing nut

11. Electric connector

12. Electrical plug

Before proceeding with these operations, turn o the vacuum

cleaner and remove the plug from the power socket.

■ Use the lever (2) to release vacuuming unit (1), remove

the plug (12) connected to the electric system box and

disconnect the compressed air hose (4), then remove the

vacuuming unit (1) from the vacuum cleaner by pulling it

up and out.

■ Disconnect the compressed air hose (4) by releasing its

quick-t coupling.

■ Disconnect the electric cable (5) by releasing the connector

(11).

■ Use the lever (6) to remove the cover (7).

■ Remove the support (8) with the lter cartridges.

■ Remove the lters cartridge (9) by unscrewing the xing

nuts (10).

■ Assemble the new lter cartridges and proceed in the

reverse order of removal to install all the components,

making sure that the previously disconnected electrical

and pneumatic connections have been reconnected.

When reassembling, turn the cover until the

electropneumatic device is in the right position for the

cartridge support.

■ Dispose of the old lter cartridges according to the laws

in force.

HEPA lter replacement

WARNING!

Take care not to raise dust when this operation is

carried out. Wear a P3 mask and other protective

clothing plus protective gloves (DPI) suited to the

hazardous nature of the dust collected, refer to the

laws in force.

Figure 10

1. Vacuuming unit

2. Locking lever

3. Absolute lter lock ring

4. Absolute lter disc

5. Absolute lter

WARNING!

Reassemble with care to avoid trapping your hands

between the vacuum unit and the container. Use

gloves that provide protection against mechanical

risks (EN 388) with a level of protection CAT. II.

Before proceeding with these operations, turn the vacuum

cleaner o and disconnect the plug from the power socket.

■ Use lever (2) to release vacuum unit (1) then pull it up

and out of the vacuum cleaner.

■ Unscrew ring (3).

■ Pull out disc (4) and absolute lter (5).

■ Place absolute lter (5) in a plastic bag, close the bag

hermetically and dispose of the lter in accordance with

the laws in force.

■ Insert a new lter (5) with the same ltering

characteristics as the removed one.

■ Lock the absolute lter with disc (4) and tighten ring

(3).

■ Replace vacuum unit (1).

■ Fix the vacuuming unit using the lever (2).

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

11/16

I

US

Tightness inspection

Hoses check

Make sure the connecting hoses (Fig. 12) are in a good

condition and correctly xed.

If the hoses are damaged, broken or badly connected to the

unions, they must be replaced.

When sticky materials are treated, check for possible

clogging along the hose, in the inlet and on the bae plate

inside the ltering chamber.

Scrape inlet (2 - Fig. 12) from the outside and remove the

deposited waste as indicated in gure 12.

Filtering chamber tightness check

If gasket (1 - Fig. 13) between container (4) and lter

chamber (3) fails to guarantee a good seal:

■ Loosen the four screws (2) that lock the ltering

chamber (3) against the vacuum cleaner structure.

■ Allow the ltering chamber (3) to lower down and tighten

the screws (2) once it has reached the tightness position.

If an optimal seal cannot be obtained and the gasket is torn

or cracked, etc. it must be replaced.

Wiring diagram list

Figure 14

1. Compressor

2. Motor head

Q1. Main switch

TS2. Cyclic timer

TR1. Transformer

M1. Clamp

XC2. Connector

H2. Light intervention of the compressor motor

protection

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

12/16

I

US

Procedure for Longopac

®

system installation

2. Insert the Longopac

®

bag and cut the connections

3. Prepare the bag on the stand, pull out the end and start

1. Remove the holder

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

13/16

I

US

4. Place the holder on the vacuum cleaner

5. “Duck-neck” closure of the bag with adhesive tape

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

14/16

I

US

Procedure for hose removal

2. Place the vacuum

plug

1. Remove the hose,

including its

coupling, from the

vacuum cleaner

3. Roll the hose 4. Thread the two ends

into each other

5. Use a belt or tape to

transport and store

away from dust

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

15/16

I

US

Recommended spare parts

The following is a list of spare parts that should be kept ready at hand in order to speed up maintenance operations.

Refer to the manufacturer’s spare parts catalogue when ordering spare parts.

Description Code

Primary cartridge lter 490803-1

Filter ring seal Z8 17026

Filter chamber gasket 40000762

Absolute lter 4081700936

230V 1000W Motor 40000937

110V 800W Motor 40000938

Brushes (carbon) for 230V 1000W motors (2 brushes) 40000885

Brushes (carbon) for 110V 800W motors (2 brushes) 40000886

www.blastrac.com ‒ info@blastrac.com

Instruction manual BDC-24-230V-P

16/16

I

US

Troubleshooting

Problem Cause Remedy

The vacuum cleaner does not

start

Lack of power supply

Check for power at the socket.

Check the condition of the socket and the

cable.

Ask for assistance to be performed by a

qualied manufacturer’s technician.

The vacuum cleaner does not

start

(Low pressure indicator ON)

Low pressure in the pneumatic

system

Make sure that the compressor is working

and that there are no leaks in the pneumatic

system.

The vacuuming unit revolutions

increase

Clogged cartridge lters Replace them with others of identical type

Clogged vacuum hose Check the vacuum hose and clean it.

Dust leaks from the vacuum

cleaner

Filters are broken Replace them with others of identical type.

Inadequate lter

Replace it with another of a suitable category

and check.

Noisy motors

Motor brushes (carbon) worn or

broken

Remove and replace the (carbon) motor

brushes.

Electrostatic current on the

vacuum cleaner

Non existent or inecient

grounding

Check all ground connections. In particular on

the vacuum inlet tting; replace the hose with

an antistatic hose.

www.blastrac.com ‒ info@blastrac.com

Manuel d’instructions BDC-24-230V-P

1/16

I

F

Index

Mode d’emploi ................................................................................... 2

Sécurité de l’opérateur .................................................................................... 2

Informations générales sur l’utilisation de l’aspirateur .......................................... 2

Utilisations prévues ......................................................................................... 2

Utilisations inappropriées ................................................................................. 2

Recommandations générales ............................................................................ 3

Description de l’aspirateur ................................................................ 4

Composants de l’Aspirateur et étiquettes ............................................................ 4

Options de transformation ................................................................................ 4

Accessoires .................................................................................................... 4

Emballage et déballage .................................................................................... 4

Déballage, manutention, emploi et stockage ....................................................... 4

Mise en service - raccordement au réseau d’alimentation électrique ....................... 5

Rallonges ....................................................................................................... 5

Aspiration de substances sèches ....................................................................... 5

Entretien et réparation ..................................................................................... 5

Caractéristiques techniques (US) ....................................................................... 6

Dimensions .................................................................................................... 6

Commandes et indicateurs ............................................................................... 7

Contrôles avant la mise en marche .................................................................... 7

Mise en marche et arrêt ................................................................................... 7

Fonctionnement .............................................................................................. 8

Fonctionnement des ltres primaires à cartouche ................................................ 8

Arrêt d’urgence ............................................................................................... 8

Vidange de la cuve à poussières ........................................................................ 8

Mode de remplacement des sacs ....................................................................... 9

Remplacement et utilisation du système de vidange basculant .............................. 9

Utilisation et entretien du compresseur .............................................................. 9

En n de poste ............................................................................................... 9

Entretien, nettoyage et décontamination ............................................................ 9

Remplacement des cartouches des ltres ..........................................................10

Remplacement du ltre absolu .........................................................................10

Contrôle des étanchéités .................................................................................11

Mise à la ferraille de l’aspirateur .......................................................................11

Légende schéma électrique .............................................................................11

Procédure pour l’installation du système Longopac .............................................12

Procédure de retrait du tuyau ..........................................................................14

Pièces détachées conseillées ........................................................... 15

Recherche des pannes ..................................................................... 16

Traduction des instructions originales

www.blastrac.com ‒ info@blastrac.com

Manuel d’instructions BDC-24-230V-P

2/16

I

F

Mode d’emploi

ouvert.

■ Prévoir toujours un espace libre autour de l’aspirateur

pour permettre un accès aisé aux commandes.

La machine a été conçue pour être utilisée par un seul

opérateur.

Cet aspirateur est formé d’une unité d’aspiration motorisée,

précédée d’une unité ltrante et munie d’une cuve pour la

collecte de la matière aspirée.

Utilisations inappropriées

ATTENTION !

Sont formellement interdits :

■ Utilisation en plein air en cas de précipitations

atmosphériques.

■ Utilisation de l’aspirateur sur des surfaces non

planes et non horizontales.

■ Utilisation sans l’unité ltrante prévue par le

fabricant.

■ Utilisation avec l’embout et/ou le tuyau

d’aspiration tournés vers le corps humain.

■ L’utilisation sans couverture de l’unité

d’aspiration.

■ Utilisation sans avoir installé la cuve de

récupération.

■ L’utilisation sans les abris, les protections

et les dispositifs de sécurité installés par le

fabricant.

■ Utilisation de l’aspirateur en occluant

partiellement ou totalement les prises d’air de

refroidissement des composants à l’intérieur.

■ Utilisation de l’aspirateur couvert par des toiles

en plastique ou en tissu.

■ L’utilisation avec les bouches d’échappement

d’air complètement ou partiellement fermées.

■ L’utilisation dans des endroits exigus, qui ne

permettent pas l’échange d’air.

■ L’aspiration de liquides avec des aspirateurs

non munis de systèmes originaux d’arrêt

spéciques.

■ Aspirer les matières suivantes :

1. matières ardentes (braises, cendres chaudes,

cigarettes allumées, etc.).

2. ammes libres.

3. gaz combustibles.

4. liquides inammables, combustibles agressifs

(essence, solvants, acides, solutions

alcalines, etc.).

5. poussières/substances et/ou mélanges

explosifs et à allumage spontané (poussières

de magnésium ou d’aluminium, etc.).

Remarque : Tout ce qui a été mentionné ci-dessus

n’inclut pas l’utilisation dolosive et cette dernière

est absolument interdite.

Lire les instructions du mode d’emploi et observer les avertissements importants de

sécurité repérés par ATTENTION !

Sécurité de l’opérateur

ATTENTION !

Avant de mettre l’aspirateur en service,

lire absolument les instructions

d’utilisation et les garder à portée de

main pour pouvoir les consulter en cas de

besoin.

L’utilisation de l’aspirateur est réservée

exclusivement au personnel expérimenté, formé et

expressément chargé du fonctionnement.

Avant l’utilisation, les opérateurs doivent être

instruits et formés à l’utilisation de l’aspirateur

et des substances pour lesquelles il doit être

utilisé, y compris la méthode sûre d’évacuation et

d’élimination de la matière recueillie.

ATTENTION !

Cet aspirateur ne doit pas être utilisé par des

personnes (y compris des enfants) présentant des

troubles psychiques, sensoriels ou mentaux ou

ayant un degré d’instruction et de connaissance

insusant, à moins qu’ils soient toujours

surveillées par des personnes compétentes ou qu’ils

aient reçu d’elles les instructions d’utilisation de

l’aspirateur.

Les enfants doivent être surveillés an qu’ils ne

jouent pas avec l’aspirateur.

Informations générales sur

l’utilisation de l’aspirateur

L’utilisation de l’aspirateur est soumise aux normes

internationales en vigueur.

En plus des instructions du mode d’emploi et des règlements

en vigueur dans le Pays où il est utilisé, pour la prévention

des accidents il est nécessaire d’observer les règles

techniques pour un travail sûr et correct (EU et où applicable

: Législation relative à la sécurité sur le lieu de travail,

Directive Communautaire 89 / 391 / CE et suivant).

Eviter tout travail pouvant porter atteinte à la sécurité des

personnes, des choses et de l’environnement.

Observer les informations et les prescriptions de sécurité

contenues dans ce manuel d’instructions.

Utilisations prévues

Cet aspirateur convient pour l’emploi commercial, par

exemple dans des hôtels, des écoles, des hôpitaux, des

usines, des magasins, des bureaux, des résidences, pour

l’emploi en location et de toute manière pour des emplois

diérents du simple usage domestique.

Cet aspirateur convient pour les travaux de nettoyage et

de collecte de matières solides en lieux couverts et à ciel

La page charge ...

Blastrac BDC-24 Le manuel du propriétaire

Ce manuel convient également à

Blastrac BDC-24 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents