Matrox Millennium G450 Manuel utilisateur

Millennium G450 • Millennium G450 LE

User Guide

10711-301-0102

2000.08.25

ENGLISH

2 Matrox Graphics Card – User Guide

Hardware installation

This section describes how to install your Matrox card. For information specific to your computer,

like how to remove its cover, see your system manual.

1

Switch to the standard VGA display driver

If you’re running Windows 95/98/2000 on your computer, this step isn’t necessary.

If you’re using another operating system (for example, Windows NT 4.0), see its

documentation for how to switch to VGA mode.

2

Open your computer and

remove your existing graphics

card

*

Turn off your computer and all peripherals

such as your monitor or printer. Open the

computer and remove your existing graphics

card (if any). (If graphics hardware is built

into the motherboard of your computer, this

graphics hardware should automatically

disable itself after your Matrox card is

installed.)

WARNING:

To avoid personal injury, turn off your computer, unplug it, and then wait for

it to cool before you touch any of its internal parts. Also, static electricity can severely

damage electronic parts. Before touching any electronic parts, drain static electricity from

your body (for example, by touching the metal frame of your computer). When handling a

card, carefully hold it by its edges and avoid touching its circuitry.

* With multi-display mode, you may be able to use your existing graphics card. For Windows 98/2000, see Windows 98/2000

online help under “Multiple Display Support”. For Windows NT 4.0, only Matrox graphics card models supported by the Matrox

display driver can be used.

Matrox Graphics Card – User Guide 3

3

Choose an expansion slot

Most computers have different types of

expansion slots. Choose an AGP or PCI slot,

depending on the type of Matrox card you

have. Your system manual should identify

the location of each type of expansion slot in

your computer.

4

Insert your Matrox card

a

Remove the cover for the slot you

intend to use.

b

Save the screw for the mounting

bracket. Position your Matrox card over

the expansion slot you’ve chosen.

c

Push the card in firmly and evenly until

it’s fully seated in the slot.

d

Replace the screw to secure the bracket

of your Matrox card to the computer

frame.

WARNING:

Inserting your Matrox card

into the wrong type of slot could damage

your card, your computer, or both.

If you have an AGP card,

don’t

insert the

plastic tab (see picture) into the slot.

AGP slot

PCI slot

ISA slot

(Back of computer)

AGP cardPCI card

Plastic

tab

4 Matrox Graphics Card – User Guide

5

Connect your monitors

Simply plug your monitor cables into the

monitor connectors on your Matrox card.

Make sure each end of the monitor cables

are properly connected and fastened.

Your Matrox card is now installed. To get the most out of your Matrox card, install Matrox software

– see “Software installation”, page 5.

Note:

Before you restart your computer,

make sure your monitors are turned on. Do

this each time you restart your computer.

Otherwise, the software may not be able to

properly detect your monitors.

Note:

With the special TV output adapter

*

included with your Matrox product, you can

connect a TV or video recorder to the

secondary

connector on your graphics card.

For more information, see “TV output” in

the online version of this guide.

* If your Matrox product was included with your computer, your product may not include this adapter.

Main

connector

Secondary

connector

If you only have one monitor,

use this connector.

TV output adapter

*

Matrox Graphics Card – User Guide 5

Software installation

This section describes how to install Matrox software for

Windows 95/98

*

/2000 or NT 4.0

. (For other operating systems,

see the

Readme

file in the root folder of the Matrox installation

CD-ROM.)

Windows 2000 or NT 4.0 –

You may need administrator rights

to install certain software. For more information, see Windows

documentation.

1

Restart your computer

If you’re using Windows 95/98/2000

, it detects new

hardware when you restart. If Matrox display drivers haven’t been previously installed,

Windows reports finding a PCI adapter (even if you have an AGP card). Windows prompts

you to install a display driver. Follow the on-screen instructions. (The Matrox Windows

95/98 display driver is in the

Win9x

folder of your Matrox installation CD-ROM. The Matrox

Windows 2000 display driver is in the

Win2k

folder.)

2

Install required software

After your computer has restarted, insert (or reinsert)

the Matrox installation CD-ROM in your CD-ROM drive – the setup program automatically

starts.

†

This setup program works with Windows 95/98/2000

and NT 4.0, and detects which

operating system you’re using. If the required display software isn’t already installed, the

setup program automatically prompts you to install this software. Follow the on-screen

instructions.

After the required display software is installed, you’re prompted to restart your computer for

changes to take effect. Leave your Matrox CD-ROM in your CD-ROM drive.

3

Install optional software

After your computer restarts, the setup program shows

you a list of additional items you can install. For each item you want to install, select a list

item, click

Install

, then follow the on-screen instructions.

4

Set up your display software

See “Software setup”, page 6.

* Unless otherwise indicated, references to

Windows 98

apply to

Windows Me

(Millennium Edition).

2

k2k

9x

NT 2

k

9x

NT

2

k2k

NT

2

k

NT

2

k2k

9x

2

k

9x

† If Windows doesn’t automatically start the setup program, you can start it manually from the root folder of the CD-ROM.

6 Matrox Graphics Card – User Guide

Software setup

Your Matrox display driver includes Matrox PowerDesk software. This software helps you get the

most out of your Matrox graphics card. This section has important information on how to configure

your display settings using Matrox PowerDesk software.

Accessing PowerDesk property sheets

Many display controls are on Matrox PowerDesk property sheets. You can identify

Matrox PowerDesk property sheets by the icon appearing on the tab. To access

these property sheets:

!

Windows 95 –

Right-click your Windows desktop background, then click

Properties

.

!

Windows 98/2000 –

Right-click your Windows desktop background, then click

Properties

"

Settings

"

Advanced

. If you’re using a multi-display desktop, select a

display before clicking

Advanced

.

!

Windows NT 4.0 –

Click

"

Programs

"

Matrox PowerDesk NT

"

Matrox

Display Properties

.

Also, to quickly access PowerDesk features, click the Matrox QuickDesk icon ( ) on your

Windows taskbar.

Monitor setup

Before changing your display resolution, color palette, or other Matrox PowerDesk settings, make

sure correct software monitor settings are selected. If you have a Plug-and-Play (DDC) monitor, the

correct settings are usually automatically selected. The following explains how to make sure your

monitor settings are okay.

9595

2

k2k

9

898

2

k

9

8

NTNT

Note:

Multi-display mode is supported under Windows 98/2000 and NT 4.0. For more

information on multi-display mode, see Windows 98/2000 online help under “Multiple

Display support” and see “DualHead Multi-Display setup”, page 7. (Windows 95 doesn’t

support multiple displays.)

WARNING:

If incorrect software monitor settings are applied,

some

monitors can be

permanently damaged. For more information, see your monitor manual.

Matrox Graphics Card – User Guide 7

Windows 95/98/2000 –

If you have a Plug-and-Play (DDC) monitor, Windows should

automatically use the correct settings for your monitor. To make sure the correct monitor is

selected in Windows:

1

Right-click your Windows desktop background, then click

Properties

"

Settings

.

2

Depending on what version of Windows you have, click

Change Display Type

, or

Advanced Properties

"

Monitor

, or

Advanced

"

Monitor

. If you’re using a multi-display

desktop, select a display before clicking

Advanced

.

3

If the monitor name listed doesn’t match your monitor, click the

Change

button to select

a new monitor name. Follow the on-screen instructions.

For more information on Windows monitor settings, see Windows documentation.

If you want to customize your Windows monitor settings:

1

Access the PowerDesk

Monitor Settings

property sheet (see “Accessing PowerDesk

property sheets”, page 6).

2

Depending on what you want to do, click one of the buttons in the

Monitor settings

selection method

box, then follow the on-screen instructions.

Windows NT 4.0

–

1

Click

"

Programs

"

Matrox PowerDesk NT

"

Matrox Display Properties

"

Monitor

.

2

If you have a Plug-and-Play monitor:

Make sure the

Plug-and-Play (DDC) monitor

button is

selected. If so, the Matrox display driver

automatically

uses the correct settings for your

monitor. If not, click this button, then click

Apply

.

If you don’t have a Plug-and-Play monitor:

See if the

Default monitor (60 Hz)

button is selected. If

so, use the Matrox monitor selection method. For more information on Matrox monitor

selection, see Matrox PowerDesk online documentation.

DualHead Multi-Display setup

With your Matrox graphics card, you can enable a second display (for example, a computer monitor

or a TV) as part of your Windows desktop. This is the Matrox

DualHead Multi-Display

feature. To

use this feature:

Windows 98 –

1

Access the PowerDesk

DualHead

property sheet (see “Accessing PowerDesk property

sheets”, page 6).

2

Select the

DualHead Multi-Display

option button.

2

k2k

9x

2

k

9x

NTNT

9898

8 Matrox Graphics Card – User Guide

3

Click

OK

"

Yes

to restart your computer and for changes to take effect.

4

If multi-display mode isn’t automatically enabled when you restart Windows:

a

Right-click your Windows desktop background, then click

Properties

"

Settings

.

b

Select the disabled display, enable the

Extend my Windows desktop onto this

monitor

check box, then click

OK

.

Windows 2000 –

1

Access the PowerDesk

DualHead

property sheet (see “Accessing PowerDesk property

sheets”, page 6).

2

Select the

DualHead Multi-Display

option button.

3

Click

Multi-Display Settings

to adjust your DualHead Multi-Display settings. Click

OK

when you’re done.

4

Click

OK

"

OK

for changes to take effect.

5

Move the

Screen area

slider to adjust your display resolution and to select single-display

or DualHead Multi-Display mode. A DualHead Multi-Display resolution is twice as

wide or tall as its corresponding single-display resolution. For example, 640 × 480 is a

single-display resolution and 1280 × 480 is a DualHead Multi-Display resolution.

6

Click

OK

to accept your changes.

Windows NT 4.0 –

1

Click

"

Programs

"

Matrox PowerDesk NT

"

Matrox Display Properties

"

DualHead

.

2

Select the

DualHead Multi-Display

option button.

3

Click

OK

"

Yes

to restart your computer and for changes to take effect.

4

Click

"

Programs

"

Matrox PowerDesk NT

"

Matrox Display Properties

"

Settings

.

5

Click

Multi-Display Desktop

().

Note:

In DualHead Multi-Display mode under Windows 2000, Windows treats the main

and secondary displays as a single display (which the Matrox display driver divides between

two monitors). As a result, these displays always use the same resolution and color palette

settings. The resolution of both displays is limited by the display with the lower maximum

resolution.

2k2k

NTNT

Matrox Graphics Card – User Guide 9

6

Move the

Desktop area

slider to adjust your multi-display desktop, then click

OK

to

accept your changes.

Other DualHead features

If your Matrox graphics card has a second monitor connector you can also use these features:

Windows 95/98/2000 or NT 4.0 –

!

DualHead Clone

– View a copy of your main display on your secondary display. Each

display can use different monitor settings (refresh rates).

!

DualHead Zoom

– Use your secondary display to view a zoomed-in portion of your main

display.

Windows 95/98/2000 –

!

DualHead DVDMax

– Play digital video in a window on your main display and, at the

same time, view that video full-screen on a TV.

More PowerDesk information

For more information on Matrox PowerDesk:

Windows 95/98/2000 or NT 4.0 –

!

For context-sensitive help where available, click the “” icon in the title bar, then click

the item you want help on. Right-click a help topic for a pop-up menu that lets you print

or copy it. (Some help topics are only available through context-sensitive help.)

Windows 95/98/2000 –

!

Access the PowerDesk

Information

property sheet (see “Accessing PowerDesk property

sheets”, page 6), then click

Help

or

View Readme File

.

Windows NT 4.0 –

!

Click

"

Programs

"

Matrox PowerDesk NT

"

Matrox Display Properties

"

Information

.

!

Click

"

Programs

"

Matrox PowerDesk NT

"

Matrox PowerDesk Guide

.

!

Click

"

Programs

"

Matrox PowerDesk NT

"

Readme

.

Note:

In multi-display mode under Windows NT 4.0, the same display resolution and color

palette is used for each display.

Note:

You can also use your main and secondary display for two distinct views in games

that use the DualHead Multi-Display feature. For more information on games that use this

feature, see the Matrox Web site (www.matrox.com/mga

).

2

k2k

9x

NT 2

k

9x

NT

2

k2k

9x

NT 2

k

9x

NT

2

k2k

9x

2

k

9x

NTNT

10 Matrox Graphics Card – User Guide

Troubleshooting

Basic procedures

This section explains basic procedures that are referred to by some troubleshooting items in this

guide.

Restarting in safe mode

What follows is information on how to restart your computer in

safe mode

(or

VGA mode

).

If your primary display is

usable

:

Windows 95/98/2000 or NT 4.0 –

1

Restart your computer:

#

Windows 95/98 –

Click

"

Shut Down

"

Restart

"

OK

.

#

Windows 2000 –

Click

"

Shut Down

, select

Restart

, then click

OK

.

#

Windows NT 4.0 –

Click

"

Shut Down

"

Restart your computer

"

Yes

.

2

Windows 95/98/2000 –

Before

Windows starts, press [F8] for the Windows startup

menu to appear. (With Windows 98, if [F8] doesn’t work, instead try pressing and

holding [Ctrl] before Windows starts.)

3

Select “safe mode” or “VGA mode”, then press [Enter].

If your primary display is

unusable

:

Windows 95/98 –

1

Press [Ctrl]+[Alt]+[Del] twice to restart your computer.

2

Before

Windows starts, press [F8] for the Windows startup menu to appear. (With

Windows 98, if [F8] doesn’t work, instead try pressing and holding [Ctrl] before

Windows starts.)

3

Select “safe mode”, then press [Enter].

Windows 2000 –

1

Press [Ctrl]+[Alt]+[Del]

"

[Tab]

"

[Tab]

"

[Enter]

"

[

$

] (down arrow)

"

[Enter] to

restart your computer.

2

Before

Windows starts, press [F8] for the Windows startup menu to appear.

3

Select “safe mode”, then press [Enter].

2

k2k

9x

NT 2

k

9x

NT

9x9x

2k2k

Matrox Graphics Card – User Guide 11

Windows NT 4.0 –

1

Press [Ctrl]+[Alt]+[Del]

"

[Tab]

"

[Tab]

"

[Enter]

"

[

$

] (down arrow)

"

[Enter] to

restart your computer.

2

From the startup menu, choose Windows “VGA mode”.

Main troubleshooting

This section addresses possible problems that could prevent you from using your computer.

Problem Computer doesn’t display information or boot after Matrox card is installed

1

Cause

Your Matrox card may not be properly installed.

1

Solution

Make sure your Matrox card is properly installed. Specifically, make sure the card is firmly

inserted in its expansion slot and that all connections to it are firmly in place. For more

information, see “Hardware installation”, page 2.

2

Cause

There may be an unsupported graphics adapter in your computer. (For Matrox

multi-display

mode

in Windows NT, all graphics cards in your computer must be Matrox cards supported

by the display driver.)

1

Solution

If an unsupported graphics card is plugged into an expansion slot, remove it.

2

Solution

If a graphics adapter is built into your computer motherboard, your system may not have

automatically disabled it when you inserted your Matrox card. Check your system manual

for instructions on how to disable your computer’s built-in graphics adapter.

3

Cause

Your computer BIOS (Basic Input/Output System) may not be up to date. For more

information on your computer BIOS, see your system manual.

1

Solution

Reinstall your previous graphics card and, if possible, update your computer BIOS. This can

usually be done with software from the manufacturer of your computer. Contact your system

vendor or manufacturer to get a BIOS update for your computer.

To get the correct BIOS update, you may need to know the serial number your computer

displays when it restarts. (This number is usually in the lower-left corner of the display.)

NTNT

12 Matrox Graphics Card – User Guide

4

Cause

The BIOS of your Matrox graphics card may need to be updated or restored.

1

Solution

For advanced users –

If you have another VGA-compatible graphics card (ISA or PCI), you

can try resetting the BIOS of your Matrox graphics card.

1

Turn off your computer and insert the other graphics card into an expansion slot. For

more information on expansion slots, see “Choose an expansion slot”, page 3.

2

Plug your monitor into the other graphics card and restart your computer.

3

Make sure

Matrox System Utilities

are installed on your computer. (These can be

installed from your Matrox CD-ROM.)

4

Restart your computer in DOS mode, then type:

cd c:\matrox\util

[Enter]

upbiosdos

[Enter]

5

Turn off your computer, remove the other graphics card, then plug your monitor into

your Matrox graphics card.

6

Restart your computer.

Problem Wrong color balance, screen image off-center, or no picture at all

1

Cause

Your monitor video controls may be improperly set.

1

Solution

Adjust your monitor controls (brightness, contrast, and so on). For more information, see

your monitor manual.

2

Cause

Your monitor may not be properly connected.

1

Solution

Make sure your monitor is properly connected to the correct connector on your Matrox

graphics card (see “Connect your monitors”, page 4).

Note:

Make sure your computer uses the other graphics card to control your primary

display. The graphics card that controls your primary display is the one that first displays

information when you restart your computer. (A DualHead-supporting graphics card

may display this startup information on both of its displays at the same time.)

Your computer BIOS (Basic Input/Output System) and the slot type (ISA, PCI, or AGP

– see “Choose an expansion slot”, page 3) of each graphics card help determine which

graphics card controls your primary display.

To control which graphics card is used for your primary display, you may be able to

change the configuration of your computer BIOS. For information on how to change

your computer BIOS settings, see your system manual.

Matrox Graphics Card – User Guide 13

2

Solution

Make sure the monitor power cable is firmly in place.

3

Solution

Make sure the connection to the back of the monitor is firmly in place.

If your monitor uses BNC input, make

sure the Red (

R

), Green (

G

), Blue (

B

),

Horizontal Sync (

HSYNC

– white or gray

wire), and Vertical Sync (

VSYNC

– black

wire) connections are firmly in place and

plugged into the correct input.

3

Cause

If your monitor uses BNC input, one or more connection settings may be incorrect.

1

Solution

Set each of your monitor RGB input and sync switches (if available) to 75 ohms, with the

sync set to “external”. These controls are usually switches on the back of your monitor.

4

Cause

If display problems occur after the startup screen of your operating system, your software

monitor settings may be incorrect.

1

Solution

Make sure correct software monitor settings are selected.

If your primary display is still usable, see “Monitor setup”, page 6. Otherwise, see the next

troubleshooting item.

Problem After the startup screen, or after display settings are changed,

the screen image is garbled or unusable

(blank screen, rolling or overlapping screen images)

1

Cause

The Matrox display driver may be trying to use settings your monitor doesn’t support. This

can happen if a monitor was never selected in the software and the display resolution was

changed to one your monitor doesn’t support, or if the monitor connected to your computer

was changed without changing it in the software.

1

Solution

Windows 95/98/2000 –

1

If your primary display is unusable, restart your computer in safe mode (see “Restarting

in safe mode”, page 10).

2

Right-click the Windows desktop background, then click

Properties

"

Settings

.

3

Move the

Desktop area

(Windows 95) or

Screen area

(Windows 98/2000) slider down

to its lowest setting, then click

OK

.

Bayonet Nut Connect (BNC)

2

k2k

9x

NT 2

k

9x

NT

WARNING:

If incorrect software monitor settings are applied,

some

monitors can be

permanently damaged. For more information, see your monitor manual.

2

k2k

9x

2

k

9x

14 Matrox Graphics Card – User Guide

4

Restart your computer normally.

5

Make sure the correct monitor is selected in Windows (see “Monitor setup”, page 6).

6

Make sure you’re not using inappropriate monitor setting customizations: Access the

PowerDesk

Monitor Settings

property sheet (see “Accessing PowerDesk property

sheets”, page 6), then click

Delete all customizations

.

7

Restore your original display settings (see steps 2 and 3).

Windows NT 4.0 –

1

If your primary display is unusable, restart your computer in VGA mode (see

“Restarting in safe mode”, page 10).

2

Right-click the Windows desktop background, then click

Properties

"

Settings

.

Windows may prompt you that the display settings are incorrect for the current mode;

click

OK

to continue.

3

Move the

Desktop area

slider down to its lowest setting, then click

OK

.

4

Restart your computer normally.

5

Select a monitor with the Matrox PowerDesk

Monitor

property sheet, then adjust your

display settings. For more information, see the Matrox PowerDesk online

documentation.

Note:

In multi-display mode (see “DualHead Multi-Display setup”), each monitor has its

own monitor settings (refresh rates).

NTNT

Matrox Graphics Card – User Guide 15

2

Cause

Files on your system may have been deleted or corrupted.

1

Solution

Remove, then restore Matrox software:

Windows 95/98/2000 or NT 4.0 –

1

If your primary display is unusable, restart your computer in safe mode or VGA mode

(see “Restarting in safe mode”, page 10).

2

To remove Matrox software:

#

Windows 95/98/2000 –

Click

"

Settings

"

Control Panel

"

Add/Remove

Programs

(double-click)

"

Matrox Graphics Software (remove only)

"

Add/Remove

"

Yes

.

#

Windows NT 4.0 –

Run the separate uninstall program included with

Matrox

System Utilites

. For more information, see the

Readme

file on your Matrox

installation CD-ROM.

3

After removing Matrox software, install the latest display driver for your Matrox

graphics card. You may also need to reinstall other Matrox software.

Note:

Before removing software, make sure you have all the necessary files to reinstall

software that may still be needed. Also, make sure the display driver you reinstall supports

all

Matrox products in your computer.

2

k2k

9x

NT 2

k

9x

NT

16 Matrox Graphics Card – User Guide

More information

We provide additional documentation in help files,

Readme

files, and Adobe Acrobat PDF (Portable

Document Format) files. To view or print PDF files, use the

Acrobat Reader

program, which you can

install from the Matrox installation CD-ROM. This guide is available on the CD-ROM as a PDF file

(

Doc\English\Guide\Guide_en.pdf

).

The online version of this guide has additional information, including the following sections: “TV

output”, “Extra troubleshooting”, “Display information”, “Hardware information”, “Customer

support”, “Warranty”, and “Software license agreement”.

The “Extra troubleshooting” section includes more information on the following problems:

• Can’t use Windows, Windows reports a

configuration error, and/or can’t install or uninstall

Matrox display driver

• Monitor settings aren’t automatically detected

• After game for Windows 95/98/2000 starts, monitor

doesn’t display properly

• Matrox Diagnostic or setup program reports an IRQ

problem

• Game for Windows 95/98 doesn’t start or runs

slower than normal

• After restarting computer, Windows 95/98 warns

that the graphics card isn’t configured correctly

• Using multiple displays under Windows 98/2000 or

NT 4.0, program doesn’t work with main graphics

card

• Not all graphics cards in the computer are fully

supported

• In multi-display mode, displays aren’t numbered

consecutively

• Screen image defects appear, program doesn’t run

properly, or Windows doesn’t work properly

• Program window or dialog box doesn’t appear on

screen

• Video file playback is jerky (skipping frames)

• DVD video playback is jerky (skipping frames)

• Can’t play certain DVD videos

• Can’t record DVD video

• TV image is garbled or unusable

• Computer text is hard to read with a TV

• Poor TV or video recorder image quality

• Can’t record video with a video recorder

• Video appears stretched or squished on a TV

• Sound doesn’t record, video files play back with no

sound, or sound output is distorted or too loud

Note:

Be sure to check for any last-minute release notes at the end of this manual and in the

Matrox CD-ROM

Readme

file. Also, check the Matrox Web site (www.matrox.com/mga)

for the latest Matrox software, technical support, and product information.

Matrox Graphics Card – User Guide 17

TV output

You can view or record the secondary display of your Matrox graphics card with a TV or a video

recorder. This section describes this

TV output

feature:

Connection setup

1

Turn off computer

Windows 95/98/2000 or NT 4.0 –

To shut down your computer, click

"

Shut Down

"

Shut down

"

OK

, then turn off your computer.

2

Attach TV adapter

Attach the TV output adapter

*

included

with your Matrox product to the

Analog/TV

connector of your graphics

card.

Note:

TV output isn’t supported with full-screen DOS display modes (for example, the

information you see before Windows starts) or with standard VGA mode (for example, when

you restart Windows in “safe mode”). Older programs may use these display modes. While

one of these display modes is in use, your TV displays nothing (black).

WARNING:

Don’t change monitor connections while your computer is turned on. While

your computer is turned on, it may be using monitor settings that are specific to the current

monitor connections.

If a display device (monitor, TV or video recorder) is connected while your computer is

using settings intended for another display device, the display of the new device may be

garbled or unusable.

Some

devices may be permanently damaged if incorrect settings are

used.

2

k2k

9x

NT 2

k

9x

NT

* If your Matrox product was included with your computer, your product may not include this adapter.

TV output

adapter

*

Matrox card

Analog/TV

connector

18 Matrox Graphics Card – User Guide

3

Connect video output

To connect to a TV or a video recorder,

you’ll need a composite video (RCA) or S-

video cable.

If your video device (a TV or a video

recorder) didn’t come with one of these

cables, these types of cable are available at

most electronics stores. The type of cable

you use depends on what your video device

supports. Many video devices support

composite video connections, and some

higher-quality video devices support

S-video connections.

a

Attach one end of your composite

video or S-video cable to the

appropriate connector on your TV

adapter.

b

Attach the other end to the

VIDEO IN

*

connector on your TV

†

or video

recorder.

c

Before viewing or recording video

output directly from your computer,

make sure your TV or video recorder is

set up to use

line

input. For example, if

your TV has a

TV/VIDEO

switch, set it

to

VIDEO

; or if your video recorder has

a

TUNER/LINE

switch, set it to

LINE

.

Optionally, if you use the composite video

and

S-video connectors on your Matrox TV

adapter, you can directly connect two different video devices at the same time.

To view

and

record output from the same Matrox video connector, you can connect it to a

video recorder and connect the video recorder to a TV. For more information, see your video

recorder and TV manuals.

* The labels on your devices may not be consistent with what’s in this guide. Different manufacturers sometimes use different

labels for the same type of controls and connectors. For example, the

VIDEO IN

connector on your TV may be labeled

VIDEO 1

(or

VIDEO 2

). To match labels, see the documentation for your video devices.

† If your TV only has an antenna or cable TV connector, you can use an

RF modulator

to connect it to your Matrox card. RF

modulators are available at most electronics stores.

TV or video

recorder using

S-video

Composite

video (RCA)

cable

S-video cable

TV or video recorder

using composite video

Matrox card

TV adapter

(Note: Using the Matrox composite

video and S-video connectors at the

same time is optional.)

Matrox Graphics Card – User Guide 19

4

Connect audio output

Typically, the sound output from a computer

comes from speakers connected to your

sound card. If you prefer, you can hear or

record the sound output from your computer

using the same TV or video recorder you

connect to your graphics card. To do this,

you need an audio cable with a stereo jack

on one end and two RCA connectors on the

other end. If you don’t have this type of

cable, you can buy one at most consumer

electronics stores.

a

Plug the stereo-jack end of the audio

cable into the

LINE OUT

*

connector on

your sound card.

b

Plug the other end of the cable into the

left (

L

) and right (

R

)

AUDIO IN

connectors of your video device. For

more information, see your sound card

manual.

SCART adapter

Some video devices in Europe only have SCART

connectors. This type of connector includes video

and

audio, whereas composite video or S-video

connectors include only video.

If your TV or video recorder

only

uses a SCART

connector, you need a SCART cable adapter to

connect your computer to that TV or video recorder.

You need a SCART adapter that has at least 2 or 3

connectors – 1 video and 1 or 2 audio. The video

connector has to be either composite or S-video. If

you don’t already have this type of adapter, it should

be available at your local electronics store. To find

out if your TV or your video recorder supports

composite or S-video, see its documentation.

To use a SCART adapter, connect the SCART end of the adapter to your TV or video recorder, then

connect the other end to your Matrox TV adapter

and

sound card.

* If your sound card has no

LINE OUT

connector, you can use its

SPKR

connector instead. In this case, all your computer’s sound

output goes to the video device you connected to.

TV or video

recorder

Sound

card

S-video SCART

adapter with 3

connectors

Composite SCART

adapter with 3

connectors

SCART connector

20 Matrox Graphics Card – User Guide

Software setup

If a TV or video recorder is connected to the second monitor connector on your Matrox graphics card,

you can use TV output mode to view or record your display on your TV or video recorder. (To

connect video devices to your computer, see page 17.)

TV settings have lower resolutions and refresh rates than typical computer monitor settings. Lower

refresh rates may result in more noticeable flicker.

Windows 98/2000 –

To add a TV to your Windows desktop, see “DualHead Multi-Display

setup”, page 7.

Windows 95/98/2000 or NT 4.0 –

To use TV output, you can use the

DualHead Clone

,

DualHead Zoom

, or

DualHead DVDMax

*

features (see “Other DualHead features”, page 9).

Windows 95/98/2000 –

To adjust TV settings, access the Matrox PowerDesk

DualHead

property sheet (see “Accessing PowerDesk property sheets”, page 6). To adjust advanced

desktop TV settings, click

Desktop TV Settings

. To adjust advanced DVDMax TV settings,

click

DVDMax TV Settings

.

Windows NT 4.0 –

To adjust TV settings, click

"

Programs

"

Matrox PowerDesk

NT

"

Matrox Display Properties

"

Monitor

. To adjust advanced TV settings, click

Advanced

TV Settings

.

For more information on how you can use your secondary display, see Matrox PowerDesk

online help.

Note:

Two TV standards are supported for TV output. The NTSC standard is used in North

America and Japan, among other places. The PAL standard is used in most of Western

Europe and in China, among other places.

If an incorrect TV standard is selected in Matrox software, the output from your computer

may not appear or record properly on your TV or your video recorder. To find out what

standard your TV or video recorder supports, see its documentation.

* Under Windows NT 4.0, the DualHead DVDMax feature isn’t supported.

2

k2k

9

898

2

k

9

8

2

k2k

9x

NT 2

k

9x

NT

2

k2k

9x

2

k

9x

NTNT

La page charge ...

Matrox Millennium G450 Manuel utilisateur

Ce manuel convient également à

Matrox Millennium G450 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents