Matrox G450 MMS Manuel utilisateur

www.matrox.com/graphics

Graphics Solutions for Professionals

User Guide

10807-301-0220

2007.02.02

Matrox

G450 MMS

ENGLISH

2 Matrox G450 MMS – User Guide

Overview

Thank you for purchasing a G450 MMS (Multi-Monitor Series) graphics card. Your Matrox MMS

card is a high-performance graphics card that plugs into an expansion slot inside your personal

computer. With this card, you can use 2 or 4 computer monitors or TVs at a time.

Hardware supplied

Software supplied (for Windows 2000/XP and NT 4.0)

!

Matrox PowerDesk

– to use your Matrox graphics hardware

!

Other software

– see the CD-ROM

Readme

file

Installation overview

To install your Matrox product:

1

Install the Matrox card – see “Hardware installation”, page 3.

2

Install the software – see “Software installation”, page 8.

G450 MMS card

*

* Pictured is a G450×4 MMS card.

Dual-monitor cable

†

† 2 dual-monitor cables are included with Matrox MMS×4 products.

DVI-to-HD15 adapters

‡

‡ 2 DVI-to-HD15 adapters are included for each dual-monitor cable.

Note:

If your Matrox product is already partially or fully installed on your computer, some

or all the installation information in this guide may not apply to you. However, this

information may be useful if you need to reinstall your Matrox product.

Matrox G450 MMS – User Guide 3

Hardware installation

This section describes how to install your Matrox card. For information specific to your computer,

like how to remove its cover, see your system manual.

1 Switch to the standard VGA display driver

If you’re running Windows 2000/XP on your computer, this step isn’t necessary.

If you’re using another operating system (for example, Windows NT 4.0), see its

documentation for how to switch to VGA mode.

2 Open your computer and

remove your existing graphics

card

*

If a graphics card

isn’t

already installed in

your computer, skip to step 3.

a

Using

Add/Remove Programs

in the

Windows

Control Panel

, remove any

currently installed display drivers.

Restart your computer for the changes

to take effect.

After your computer restarts, you’re

prompted to install drivers for the new

graphics hardware detected. Click

Cancel

.

WA R NI N G :

To avoid personal injury, turn off your computer, unplug it, and then wait for

it to cool before you touch any of its internal parts.

While your computer is turned off but still plugged in, some electrical current is supplied

to the motherboard. This current may prevent newly installed hardware from working

properly.

Also, static electricity can severely damage electronic parts. Before touching any electronic

parts, drain static electricity from your body (for example, by touching the metal frame of

your computer). When handling a card, carefully hold it by its edges and avoid touching its

circuitry.

* With multi-display mode, you may be able to use your existing graphics card. For Windows 2000/XP, see Windows 2000/XP

online help under “Multiple Display Support”. For Windows NT 4.0, only Matrox graphics card models supported by the Matrox

display driver can be used.

4 Matrox G450 MMS – User Guide

b

Turn off your computer and all peripherals such as your monitor or printer.

c

Open the computer and remove your existing graphics card. (If graphics hardware is

built into the motherboard of your computer, you may need to disable it manually. For

more information, see your system manual.)

3 Choose a PCI slot

Most computers have different types of

expansion slots. Choose a

PCI

(not

PCI

Express

) slot for your graphics card. Your

card supports both 64-bit and 32-bit PCI

slots. Your system manual should identify

the location of each type of expansion slot in

your computer.)

(Back of computer)

PCI

Express

slots

PCI

slots

AGP

slot

Note:

If you’re using a PCI graphics card in a PCI 64-bit compatible slot, your choice of PCI

slot may affect your card or system performance. For more information, see your computer

manual.

WARNIN G:

Inserting your Matrox card

into the wrong type of slot could damage

your card, your computer, or both.

If you’re using a 64-bit PCI slot, your

card’s edge connector should be inserted

into only part of the PCI slot (the part

closest to the back of the computer).

AGP card

PCI card

PCIe card

32-bit

64-bit

Matrox G450 MMS – User Guide 5

4 Insert your Matrox card

a

Position your Matrox card over the

expansion slot you’ve chosen.

b

Push the card in firmly and evenly until

it’s fully seated in the slot.

c

Secure the bracket of your Matrox card

to the computer frame.

6 Matrox G450 MMS – User Guide

Connection setup

This section describes how to connect computer monitors to your Matrox product.

1 Connect your dual-monitor

cables

Attach your Matrox dual-monitor cables

*

to

the connectors on the bracket of your

Matrox MMS card. Make sure the

connectors are firmly in place.

Note:

Windows 2000/XP

– If you want to use TV output with your Matrox product, you

first need to connect at least one (1) computer monitor to be able to install the display

driver. After the display driver is installed with TV output support, you can connect your

dual-TV-output cables. For more information, see “TV output” in the online version of

this guide.

* Only one dual-monitor cable is included with Matrox MMS×2 cards.

Dual-monitor

cable

WA RN I NG :

To avoid damaging the LFH-60 connector on your

dual-monitor cable or on your graphics card, carefully insert the

connector on your dual-monitor cable as straight as possible into the

connector on your graphics card. Specifically, inserting the

connectors into each other at an angle is likely to bend and damage

the pins on the connector of the dual-monitor cable.

Matrox G450 MMS – User Guide 7

2 Connect your monitors

Connect your preferred monitor to the main

DVI connector of your multi-monitor cable.

If your monitor has a DVI connector, connect it

directly to the main DVI connector of your

multi-monitor cable.

If your monitor has an HD-15 connector, use

the DVI-to-HD15 adapter included with your

product to connect your monitor to the main

connector. Make sure the connectors are

properly fastened.

Your Matrox card is now installed. Restart your computer and install your Matrox software

(see “Software installation”, page 8).

Monitor

connector

(DVI)

DVI-to-HD15

adapter

Monitor connector

(HD15)

Note:

Monitors are numbered consecutively based

on which connector each is attached to.

Numbering starts with the primary display – the

one that first displays information when you

restart your computer. If another graphics card is

installed in your computer, display numbering

may be different.

Note:

To connect a

digital

monitor (a

monitor that uses digital input, usually a

flat panel monitor) to your Matrox

product, your monitor must have a DVI

connector.

Some monitors with DVI connectors

support both digital and analog input. If

you’re using one of these monitors with

your Matrox product, make sure it’s configured to use the correct type of input. For more

information, see your monitor documentation.

DVI connector

(digital)

HD-15 connector (analog)

DVI connector

(analog/digital)

8 Matrox G450 MMS – User Guide

Software installation

This section describes how to install Matrox

software for

Windows 2000/XP or NT 4.0

.

You may need administrator rights to install

certain software. For more information, see

Windows documentation.

1 Install display driver

Windows detects new hardware when you restart. If Matrox display drivers haven’t been

previously installed, Windows prompts you to install a display driver. Follow the on-screen

instructions. (The Matrox Windows 2000/XP display driver is in the

Win2kXP

folder of your

Matrox installation CD-ROM.)

If you want to use TV output, you need to enable the feature when you install the display

driver. For more information on TV output, see “TV output”, page 14.

After the required display software is installed, you’re prompted to restart your computer for

changes to take effect.

2 Install optional software

After your computer has restarted, insert (or reinsert) the Matrox installation CD-ROM in

your CD-ROM drive – the setup program automatically starts.

*

The setup program shows

you a list of additional items you can install. For each item you want to install, select a list

item, click

Install

, then follow the on-screen instructions.

3 Set up your display software

See “Display setup”, page 9.

Note:

This guide has references that are specific to the Matrox installation CD-ROM. If your Matrox

product wasn’t packaged by Matrox (for example, if it was included with your computer), your

product may not include this CD-ROM.

If you don’t have this CD-ROM, certain references in this guide may not reflect the software you

have. For more information, see other software documentation provided by your system vendor.

* If Windows doesn’t automatically start the setup program, you can start it manually from the root folder of the CD-ROM.

Matrox G450 MMS – User Guide 9

Display setup

Windows 2000/XP or NT 4.0 –

Your Matrox display driver includes Matrox PowerDesk software. This

software helps you get the most out of your Matrox graphics card. This section has important

information on how to configure your display settings using Matrox PowerDesk software.

Accessing PowerDesk property sheets

Many display controls are on Matrox PowerDesk property sheets. You can identify

Matrox PowerDesk property sheets by the icon appearing on the tab. To access

these property sheets:

!

Windows 2000/XP

– Right-click your Windows desktop background, then click

Properties

"

Settings

"

Advanced

. If you’re using a multi-display desktop, select a

display before clicking

Advanced

.

!

Windows NT 4.0

– Click

Start

"

Settings

"

Control Panel

"

Matrox Display Properties

(double-click).

Also, to quickly access PowerDesk features, click the Matrox QuickDesk icon ( ) on your Windows

taskbar. To see the QuickDesk icon in Windows XP, you may need to click the

Show hidden icons

button ( ) on your Windows taskbar.

Monitor setup

Before changing your display resolution, color palette, or other Matrox PowerDesk settings, make

sure correct software monitor settings are selected. If you have a Plug-and-Play (DDC) monitor,

correct settings are usually automatically selected. The following explains how to make sure your

monitor settings are okay.

Note:

Multi-display mode is supported under Windows 2000/XP and NT 4.0. For more

information on multi-display mode, see Windows 2000/XP online help under “Multiple

Display support”.

WA R NI N G :

If incorrect software monitor settings are applied,

some

monitors can be

permanently damaged. For more information, see your monitor manual.

10 Matrox G450 MMS – User Guide

Windows 2000/XP

– If you have a Plug-and-Play (DDC) monitor, Windows should

automatically use correct settings for your monitor. To make sure the correct monitor is

selected in Windows:

1

Right-click your Windows desktop background, then click

Properties

"

Settings

"

Advanced

"

Monitor

. If you’re using a multi-display desktop (see “Multi-display setup”,

page 11), select a display before clicking

Advanced

.

2

If the monitor name listed doesn’t match your monitor, click

Properties

"

Driver

"

Update driver

. Follow the on-screen instructions.

3

If you’re using a multi-display desktop (see “Multi-display setup”, page 11), repeat steps

1–2 for each display in your Windows desktop.

For more information on Windows monitor settings, see Windows documentation.

If you want to customize your Windows monitor settings:

1

Access the PowerDesk

Monitor Settings

property sheet (see “Accessing PowerDesk

property sheets”, page 9).

2

Depending on what you want to do, click one of the buttons in the

Monitor settings

selection method

box, then follow the on-screen instructions.

Windows NT 4.0 –

1

Access the PowerDesk

Monitor

property sheet (see “Accessing PowerDesk property

sheets”, page 9).

2

If you have a Plug-and-Play monitor

:

Make sure the

Plug-and-Play (DDC) monitor

button is

selected. If so, the Matrox display driver

automatically

uses correct settings for your

monitor. If not, click this button, then click

Apply

.

If you don’t have a Plug-and-Play monitor

:

See if the

Default monitor (60 Hz)

button is selected. If

so, use the Matrox monitor selection method. For more information on Matrox monitor

selection, see Matrox PowerDesk online documentation.

3

If you’re using a multi-display desktop (see “Multi-display setup”, page 11), repeat steps

1–2 for each display in your Windows desktop.

Matrox G450 MMS – User Guide 11

Multi-display setup

To set up multi-display mode:

Windows 2000/XP

– If multi-display mode isn’t automatically enabled when you restart

Windows:

1

Right-click your Windows desktop background, then click

Properties

"

Settings

.

2

Select the disabled display, enable the

Extend my Windows desktop onto this monitor

check box, then click

Apply

.

3

To change resolution and color settings for each display, select a display, then change the

Screen area

and

Colors

settings. When you’re done, click

OK

.

Windows NT 4.0

–

1

Access the PowerDesk

Settings

property sheet (see “Accessing PowerDesk property

sheets”, page 9).

2

Click

Multi-Display Desktop

().

3

Move the

Desktop area

slider to adjust your multi-display desktop, then click

OK

to

accept your changes.

Advanced multi-display setup

Windows 2000/XP

– Use

Matrox Hybrid Display

to configure advanced display settings. With this

software, you can:

!

Combine 2 or more individual displays into a single Windows display. (A

Windows

display

is a display that Windows recognizes and that can be adjusted with Windows

controls.)

!

View a

clone

(copy) of a Windows display on one or more other displays.

!

Use up to 16 displays at a time by combining or copying displays. To do this, you need

more than one supported Matrox graphics card installed in your computer. (Without

this software, the maximum number of independent displays you can use at a time with

Windows 2000/XP is 10.)

!

Rotate one or more displays to support portrait orientation. (A

portrait

orientation is

taller than wide.)

!

Change the display layout to reflect the physical layout of your monitors.

Note:

In multi-display mode under Windows NT 4.0, the same display settings (resolution

and color palette) are used for each display.

12 Matrox G450 MMS – User Guide

To set up an advanced multi-display desktop:

1

Click the Matrox QuickDesk icon ( ) on your Windows taskbar, then click

Matrox

Hybrid Display

. To see the QuickDesk icon in Windows XP, you may need to click the

Show hidden icons

button ( ) on your Windows taskbar.

2

Select

Enable an advanced multi-display setup

, then click

3

Select the maximum number of Windows displays you want to use. (Using only 1

Windows display for all your individual displays is also referred to as an

NT-style

multi-

display setup.)

4

Select the first

Undefined

display, then click

Display Setup

.

5

Make sure each of the following controls are using the setting you want. Adjust them in

this order:

a

Number of clones

b

Display layout

c

Display rotation

d

Display resolution

e

Color palette

f

Refresh rate

g

Enlarge mouse pointer

6

Click

OK

.

7

Repeat steps 4 to 6 until there are no more

Undefined

or available displays. An

Undefined

display won’t be used when Windows restarts.

8

Click

9

Click

Finish

. For changes to take effect, your computer must be restarted.

For more information on specific controls, see context-sensitive help.

Note:

You can position each Windows display through the Windows controls. To access

these controls, right-click your Windows desktop background, then click

Properties

"

Settings

.

Matrox G450 MMS – User Guide 13

More PowerDesk information

For more information on Matrox PowerDesk:

Windows 2000/XP or NT 4.0

– For context-sensitive help where available, click the “ ”

icon in the title bar, then click the item you want help on. Right-click a help topic for a

pop-up menu that lets you print or copy it. (Some help topics are only available through

context-sensitive help.)

Windows 2000/XP

– Access the PowerDesk

Information

property sheet (see “Accessing

PowerDesk property sheets”, page 9), then click

Help

or

View Readme File

.

Windows NT 4.0

–

!

Access the Matrox PowerDesk

Information

property sheet (see “Accessing PowerDesk

property sheets”, page 9).

!

Click the Matrox QuickDesk icon ( ) on your Windows taskbar, then click

Help

"

PowerDesk Guide

or

Help

"

View Readme File

.

14 Matrox G450 MMS – User Guide

TV output

With your Matrox card, you can use dual-TV-output cables

instead of dual-monitor cables. With dual-TV-output cables,

you can view or record your displays with TVs or video

recorders. While using TV output, all your displays use TV

output settings. If you want to use this feature and dual-TV-

output cables weren’t included with your Matrox product, you

can purchase them separately (see http://shopmatrox.com

).

This section describes how to use the

TV output

feature.

Connection setup

1 Turn off computer

Windows 2000/XP –

To shut down your computer, click

Start

"

Shut Down

"

Shut down

"

OK

, then turn off your computer.

Note:

To use TV output, you need to enable the feature when you install the display driver

for your Matrox product. If TV output isn’t enabled, you need to reinstall the display driver

and enable TV output. For more information, see “Connection setup”, page 6 and

“Software installation”, page 8.

Note:

TV output isn’t supported with full-screen DOS display modes (for example, the

information you see before Windows starts) or with standard VGA mode (for example,

when you restart Windows in “safe mode”). Older programs may use these display modes.

While one of these display modes is in use, your TV displays nothing (black).

Note:

Certain software (especially software that depends on hardware-based graphics

acceleration) may not work properly while TV output is used.

Dual-TV-output cable

WA R N I N G :

Don’t change monitor connections while your computer is turned on. While

your computer is turned on, it may be using monitor settings that are specific to the

current monitor connections.

If a display device (monitor, TV or video recorder) is connected while your computer is

using settings intended for another display device, the display of the new device may be

garbled or unusable.

Some

devices may be permanently damaged if incorrect settings are

used.

Matrox G450 MMS – User Guide 15

2 Replace your dual monitor cables

a

Disconnect any computer monitor

connected to your dual-monitor cables.

b

Detach any dual-monitor cable from your

Matrox card.

c

Attach your dual-TV-output cables to your

Matrox graphics card.

*

3 Connect video output

To connect to a TV or a video recorder, you’ll

need a composite video (RCA) or S-video

cable.

If your video device (a TV or a video

recorder) didn’t come with one of these

cables, these types of cable are available at

most electronics stores. The type of cable

you use depends on what your video device

supports. Many video devices support

composite video connections, and some

higher-quality video devices support

S-video connections.

For each TV or video recorder, you want to

connect to your Matrox product:

a

Attach one end of your composite video

or S-video cable to the appropriate

connector on your dual-TV-output

cable.

b

Attach the other end to the

VIDEO IN

†

connector on your TV

‡

or video

recorder.

* Only one (1) dual-TV-output cable can be connected to Matrox MMS×2 cards.

Dual-TV-

output cable

Dual-monitor

cable

† The labels on your devices may not be consistent with what’s in this guide. Different manufacturers sometimes use different labels

for the same type of controls and connectors. For example, the

VIDEO IN

connector on your TV may be labeled

VIDEO 1

(or

VIDEO

2

). To match labels, see the documentation for your video devices.

‡ If your TV only has an antenna or cable TV connector, you can use an

RF modulator

to connect it to your Matrox card. RF

modulators are available at most electronics stores.

TV or video

recorder using

S-video

Composite

video (RCA)

cable

S-video cable

TV or video recorder

using composite video

Matrox card

Dual-TV-output

cable

(Note: Using the Matrox composite

video and S-video connectors at the

same time is optional.)

16 Matrox G450 MMS – User Guide

c

Before viewing or recording video output directly from your computer, make sure your

TV or video recorder is set up to use

line

input. For example, if your TV has a

TV/VIDEO

switch, set it to

VIDEO

; or if your video recorder has a

TUNER/LINE

switch, set it to

LINE

.

Optionally, if you use the composite video

and

S-video connectors on your Matrox TV

adapter, you can directly connect two different video devices at the same time.

To v i ew

and

record output from the same Matrox video connector, you can connect it to a

video recorder and connect the video recorder to a TV. For more information, see your video

recorder and TV manuals.

4 Connect audio output

Typically, the sound output from a

computer comes from speakers connected

to your sound card. If you prefer, you can

hear or record the sound output from your

computer using the same TV or video

recorder you connect to your graphics card.

To do this, you need an audio cable with a

stereo jack on one end and two RCA

connectors on the other end. If you don’t

have this type of cable, you can buy one at

most consumer electronics stores.

a

Plug the stereo-jack end of the audio

cable into the

LINE OUT

*

()

connector on your sound card.

b

Plug the other end of the cable into the

left (

L

) and right (

R

)

AUDIO IN

connectors of your video device. For

more information, see your sound card

manual.

* If your computer has no audio

LINE OUT

connector, you can use its

SPKR

(speaker) connector instead. In this case, all your

computer sound output goes to the video device you connected to.

TV or video

recorder

Audio

connectors

Matrox G450 MMS – User Guide 17

Software setup

If a TV or video recorder is connected to your Matrox product, you can use TV output mode to view

or record your display on your TV or video recorder. (To connect video devices to your computer, see

page 14.)

TV settings have lower resolutions and refresh rates than typical computer monitor settings. Lower

refresh rates may result in more noticeable flicker.

Windows 2000/XP –

To adjust TV settings, access the Matrox PowerDesk

DualHead

property

sheet (see “Accessing PowerDesk property sheets”, page 9).

Note:

Two TV standards are supported for TV output. The NTSC standard is used in North

America and Japan, among other places. The PAL standard is used in most of Western

Europe and in China, among other places.

If an incorrect TV standard is selected in Matrox software, the output from your computer

may not appear or record properly on your TV or your video recorder. To find out what

standard your TV or video recorder supports, see its documentation.

18 Matrox G450 MMS – User Guide

Troubleshooting

Basic procedures

This section explains basic procedures that are referred to by some troubleshooting items in this

guide.

Restarting in VGA mode

What follows is information on how to restart your computer in

VGA mode

.

Windows 2000/XP or NT 4.0 –

1

Restart your computer:

#

Windows 2000/XP

– Click

Start

"

Shut Down

"

Restart

"

OK

* to restart your

computer. (* Depending on your version and configuration of Windows, this part of

the step may not be necessary.)

#

Windows NT 4.0

– Click

Start

"

Shut Down

"

Restart the computer

"

Yes

.

If your primary monitor is unusable, see your system manual for information on how to

restart your computer using a hardware control.

2

Windows 2000/XP

–

Before

Windows starts, press [F8] for the Windows startup menu

to appear. (If [F8] doesn’t work, instead try pressing and holding [Ctrl] before Windows

starts.)

3

Select “VGA mode”, then press [Enter].

Main troubleshooting

This section addresses possible problems that could prevent you from using your computer.

Problem Computer doesn’t display information or boot after Matrox card is

installed

1

Cause

Your Matrox card may not be properly installed.

1

Solution

Make sure your Matrox card is properly installed. Specifically, make sure the card is firmly

inserted in its expansion slot and that all connections to it are firmly in place. For more

information, see “Hardware installation”, page 3.

Matrox G450 MMS – User Guide 19

2

Cause

There may be an unsupported graphics adapter in your computer. (For Matrox

multi-display

mode

in Windows NT, all graphics cards in your computer must be Matrox cards supported

by the display driver.)

1

Solution

If an unsupported graphics card is plugged into an expansion slot, remove it.

2

Solution

If a graphics adapter is built-in to your computer motherboard, your system may not have

automatically disabled it when you inserted your Matrox card. Check your system manual for

instructions on how to disable your computer’s built-in graphics adapter.

3

Cause

Your computer BIOS (Basic Input/Output System) may not be up to date. For more

information on your computer BIOS, see your system manual.

1

Solution

Reinstall your previous graphics card and, if possible, update your computer BIOS. This can

usually be done with software from the manufacturer of your computer. Contact your system

vendor or manufacturer to get a BIOS update for your computer.

To get the correct BIOS update, you may need to know the serial number your computer

displays when it restarts. (This number is usually in the lower-left corner of the display.)

Problem Wrong color balance, screen image off-center, or no picture at all

1

Cause

Your monitor video controls may be improperly set.

1

Solution

Adjust your monitor controls (brightness, contrast, and so on). For more information, see

your monitor manual.

2

Cause

Your monitor may not be properly connected.

1

Solution

Make sure your monitor is properly connected to the correct connector on your Matrox

graphics card (see “Connect your dual-monitor cables”, page 6).

2

Solution

Make sure the monitor power cable is firmly in place.

3

Cause

If display problems occur after the startup screen of your operating system, your software

monitor settings may be incorrect.

1

Solution

Make sure correct software monitor settings are selected.

If your primary display is still usable, see “Monitor setup”, page 9. Otherwise, see the next

troubleshooting item.

20 Matrox G450 MMS – User Guide

Problem After the startup screen, or after display settings are changed, the

screen image is garbled or unusable

(blank screen, rolling or overlapping screen images)

1

Cause

Analog monitors only

– The Matrox display driver may be trying to use settings your

monitor doesn’t support. This can happen if a monitor was never selected in the software and

the display resolution was changed to one your monitor doesn’t support, or if the monitor

connected to your computer was changed without changing it in the software.

1

Solution

Make sure the correct monitor is selected in Windows.

Windows 2000/XP –

1

If your primary display is unusable, restart your computer in VGA mode (see “Restarting

in VGA mode”, page 18).

2

Right-click your Windows desktop background, then click

Properties

"

Settings

.

3

Move the

Screen area

(Windows 2000) or

Screen resolution

(Windows XP) slider down

to its lowest setting, then click

OK

.

4

Restart your computer normally.

5

Make sure the correct monitor is selected in Windows (see “Monitor setup”, page 9).

6

Make sure you’re not using inappropriate monitor setting customizations: Access the

PowerDesk

Monitor Settings

property sheet (see “Accessing PowerDesk property sheets”,

page 9), then click

Delete all customizations

.

7

If necessary, restore your original display settings (see steps 2 and 3).

2

Windows NT 4.0 –

1

If your primary display is unusable, restart your computer in VGA mode (see “Restarting

in VGA mode”, page 18).

2

Right-click your Windows desktop background, then click

Properties

"

Settings

.

Windows may prompt you that the display settings are incorrect for the current mode;

click

OK

to continue.

3

Move the

Desktop area

slider down to its lowest setting, then click

OK

.

WARN I NG:

If incorrect software monitor settings are applied,

some

monitors can be

permanently damaged. For more information, see your monitor manual.

Note:

In multi-display mode, each display has its own monitor settings (refresh rates).

Make sure correct software monitor settings are selected for

each

monitor.

La page charge ...

Matrox G450 MMS Manuel utilisateur

Matrox G450 MMS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents