Simplicity 2691161-00 Manuel utilisateur

Not for

Reproduction

Zero Turn Rider

1757570USCN

Revision C

!

fr

en

Operator’s Manual

Manuel d’utilisation

Not for

Reproduction

2

Not for

Reproduction

Table of Contents

Seat and Ground Speed Lever Adjustments .........24

Cutting Height Adjustment ....................................25

Mower Removal and Installation ...........................25

Mower Deck Leveling ............................................28

Check Mower Blade Stopping Time ......................30

Battery Service ......................................................30

Troubleshooting ............................................... 32

Troubleshooting the Rider .....................................32

Troubleshooting the Mower ...................................33

Specifications ................................................... 34

Operator Safety

.................................................. 4

Safety Interlock System Tests ...............................13

Features and Controls ..................................... 14

Control Functions ..................................................14

Operation .......................................................... 16

General Operating Safety......................................16

Checks Before Starting .........................................16

Starting the Engine ................................................17

Stopping the Rider and Engine .............................17

Mowing ..................................................................17

Pushing the Rider by Hand ...................................17

Zero Turn Driving Practice ....................................18

Attaching a Trailer .................................................20

Maintenance ..................................................... 21

Maintenance Chart ................................................21

Checking Tire Pressures .......................................22

Checking/Adding Fuel ...........................................22

Fuel Filter ..............................................................22

Engine Maintenance .............................................22

Washout Port (Select Models) ..............................23

Storage..................................................................23

3

en

Not for

Reproduction

Operator Safety

Operating Safety

Congratulations on purchasing a superior-quality piece of lawn

and garden equipment. Our products are designed and manufac-

tured to meet or exceed all industry standards for safety.

Do not operate this machine unless you have familiarized yourself

with it. Reading and understanding this operator’s manual is a

way to do just that.

Power equipment is only as safe as the operator. If it is misused,

or not properly maintained, it can be dangerous! Remember, you

are responsible for your safety and that of those around you.

Use common sense, and think through what you are doing. If you

are not sure that the task you are about to perform can be safely

done with the equipment you have chosen, ask a professional:

contact your local authorized dealer.

Read the Manual

The operator’s manual contains important safety infor-

mation you need to be aware of BEFORE you operate

your unit as well as DURING operation.

Safe operating techniques, an explanation of the prod-

uct’s features and controls, and maintenance informa-

tion is included to help you get the most out of your

equipment investment.

Be sure to completely read the Safety Rules and

Information found on the following pages. Also com-

pletely read the Operation section.

Children

Tragic accidents can occur with children. Do

not allow them anywhere near the area of

operation. Children are often attracted to the

unit and mowing activity. Never assume that

children will remain where you last saw them.

If there is a risk that children may enter the

area where you are mowing, have another

responsible adult watch them.

4

Not for

Reproduction

20

3.5

Slope Operation

Operation on slopes can be dangerous. Using the unit on

a slope that is too steep where you do not have adequate

wheel traction (and control) can cause sliding, loss of

steering, control, and possible rollover. You should not

operate on a slope greater than a 3.5 foot rise over a 20

foot length (10 degrees).

Always mow up and down slopes, not across, and avoid

sudden turns or rapid speed changes. Reduce speed and

use extreme caution on ALL slopes.

Also, note that the surface condition you are on can

greatly impact your ability to safely operate this machine.

Operating on wet or slippery slopes can cause sliding and

loss of steering and control. Do not operate on slopes that

are slippery, wet, or have soft soil conditions.

If you feel unsure about operating the unit on a slope, don’t

do it. It’s not worth the risk.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and

throw debris that could seriously injure a bystander. Be sure to clean

up the area to be mowed and remove objects that could be thrown by

the blade BEFORE you start mowing. Do not operate this unit without

the entire grass catcher or discharge guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running! If some-

one does enter the area, shut the unit off immediately until they leave.

Moving Parts

This equipment has many moving parts that can injure

you or someone else. However, if you stay in the operator

zone (stay seated in the seat), and follow the safety rules

in this operator’s manual, the unit is safe to operate.

The mower deck has spinning mower blades that can

amputate hands and feet. Do not allow anyone near the

unit while it is running! Keep safety devices (guards,

shields, and switches) in place and working.

To help you, the operator, use this equipment safely, it is

equipped with an operator-present safety system. Do NOT

attempt to alter or bypass the system. See your dealer

immediately if the system does not pass all the safety

interlock system tests found in this manual

5

en

Not for

Reproduction

Fuel and Maintenance

Always disengage all drives, shutoff the engine, and

remove the key before doing any cleaning, refueling, or

servicing.

Gasoline and its vapors are extremely flammable. Do not

smoke while operating or refueling. Do not add fuel while

engine is hot or running. Allow engine to cool for at least 3

minutes prior to adding fuel.

Do not add fuel indoors, in an enclosed trailer, garage,

or any other enclosed area that is not well ventilated.

Gasoline spills should be cleaned up promptly and before

operation begins.

Gasoline should be stored only in sealed containers

approved for fuel.

Proper maintenance is critical to the safety and perfor-

mance of your unit. Keep the unit free of grass, leaves,

and excess oil. Be sure to perform the maintenance proce-

dures listed in this manual, especially periodically testing

the safety system.

Retaining Walls, Drop-Offs, and Water

Retaining walls and drop-offs around steps and water are a common hazard. Give yourself a minimum of two mower

widths of clearance around these hazards and hand-trim with a walk behind mower or string trimmer. Wheels drop-

ping over retaining walls, edges, ditches, embankments, or into water can cause rollovers, which may result in serious

injury, death, or drowning.

Enclosed Areas

Only operate this unit outdoors and away from unventi-

lated areas such as inside garages or enclosed trailers.

The engine emits poisonous carbon monoxide gas and

prolonged exposure in an enclosed area can result in

serious injury or death.

6

Not for

Reproduction

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can

cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or

death to the operator or other persons. The owner of the machine must understand these instructions and must allow

only persons who understand these instructions to operate machine. Each person operating the machine must be of

sound mind and body and must not be under the influence of any substance, which might impair vision, dexterity or

judgment. If you have any questions pertaining to your machine which your dealer cannot answer to your satisfaction,

contact the Customer Service Department.

Protection for Children

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Children who have

been given rides in the past may suddenly appear in the

mowing area for another ride and be run over or backed

over by the machine. Never assume that children will

remain where you last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

2. DO NOT allow children in yard when machine is

operated (even with the blade OFF).

3. DO NOT allow children or others to ride on machine,

attachments or towed equipment (even with the

blades OFF). They may fall and be seriously injured.

4. DO NOT allow pre-teenage children to operate

machine.

5. ALLOW only responsible adults & teenagers with

mature judgment under close adult supervision to

operate machine.

6. DO NOT operate blades in reverse. STOP BLADES.

LOOK and SEE behind and down for children, pets

and hazards before and while backing.

7. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure

vision.

Protection Against Tipovers

Slopes are a major factor related to loss-of-control and

tip-over accidents, which can result in severe injury or

death. All slopes require extra CAUTION. If you cannot

back up the slope or if you feel uneasy on the slope, DO

NOT mow it. Use extra care with grass catchers or other

attachments; these affect the handling and the stability of

the machine.

1. DO NOT operate machine on slopes exceeding 10

degrees (18% grade).

2. Exercise EXTREME CAUTION on all slopes. Turn

blades OFF when traveling uphill. Use a slow speed

and avoid sudden or sharp turns.

3. DO NOT operate machine back and forth across face

of slopes. Operate up and down. Practice on slopes

with blades off.

4. AVOID starting, stopping or turning on slopes. If

machine stops going uphill or tires lose traction, turn

blades OFF and back slowly straight down the slope.

5. STAY ALERT for holes and other hidden hazards.

Tall grass can hide obstacles. Keep away from

ditches, washouts, culverts, fences and protruding

objects.

Protection Against Tipovers

(Continued From Previous Column)

6. KEEP A SAFE DISTANCE (at least two mower

widths) away from edge of ditches and other drop

offs. The machine could turn over if an edge caves in.

7. Always begin forward motion slowly and with caution.

8. Use weights or a weighted load carrier in accordance

with instructions supplied with a grass catcher. DO

NOT operate machine on slopes exceeding 10

degrees (18% grade) when equipped with grass

catcher.

9. DO NOT put your foot on the ground to try to stabilize

the machine.

10. DO NOT operate machine on wet grass. Reduced

traction could cause sliding.

11. Choose a low enough speed setting so that you will

not have to stop or shift on a slope. Tires may lose

traction on slopes even though the brakes are

functioning properly.

12. DO NOT operate machine under any condition where

traction, steering or stability is doubtful.

13. Always keep the machine in gear when going down

slopes. DO NOT shift to neutral (or actuate hydro roll

release) and coast downhill.

Preparation

1. Read, understand, and follow instructions and warn-

ings in this manual and on the machine, engine and

attachments. Know the controls and the proper use of

the machine before starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related inju-

ries. These operators should evaluate their ability to

operate the mower safely enough to protect them-

selves and others from serious injury.

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel con-

tainer. DO NOT remove fuel cap or add fuel with

engine running. Add fuel outdoors only with engine

stopped and cool. Clean spilled fuel from machine.

DO NOT smoke.

5. Practice operation of machine with BLADES OFF to

learn controls and develop skills.

7

en

Not for

Reproduction

Preparation

(Continued From Previous Page)

6. Check the area to be mowed and remove all objects

such as toys, wire, rocks, limbs and other objects that

could cause injury if thrown by blade or interfere with

mowing.

7. Keep people and pets out of mowing area. Immed-

iately STOP blades, STOP engine, and STOP

machine if anyone enters the area.

8. Check shields, deflectors, switches, blade controls

and other safety devices frequently for proper opera-

tion and location.

9. Make sure all safety decals are clearly legible.

Replace if damaged.

10. Protect yourself when mowing and wear safety glass-

es, long pants and substantial footwear.

11. Know how to STOP blades and engine quickly in

preparation for emergencies.

12. Use extra care when loading or unloading the

machine into a trailer or truck.

13. Check grass catcher components frequently for signs

of wear or deterioration and replace as needed to

prevent injury from thrown objects going through

weak or worn spots.

Safe Handling of Gasoline

To avoid personal injury or property damage, use

extreme care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside

where there is an open flame, spark or pilot light such

as on a water heater or other appliances.

6. DO NOT fill fuel containers inside a vehicle or on a

truck or trailer bed with a plastic liner. Always place

the containers on the ground away from the vehicle

before filling.

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not pos-

sible, then refuel equipment using a portable con-

tainer, rather than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed

vehicles or trailers.

9. Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete. DO NOT use a nozzle lock-open device

10. If fuel is spilled on clothing, change clothing immedi-

ately.

11. Never overfill a fuel tank. Replace fuel cap and tigh-

ten securely.

OPERATION

1. Mount and dismount machine from left side. Keep

clear of discharge opening at all times.

2. Start engine from operator’s seat, if possible. Make

sure blades are OFF and parking brake is set.

3. DO NOT leave machine with engine running. STOP

engine, STOP blades, SET brake, and Remove key

before leaving operators position of any reason.

4. DO NOT operate machine unless properly seated

with feet on feet rests or pedal(s).

5. STOP BLADES and ENGINE and make sure blades

have stopped before removing grass catcher or

unclogging mower to prevent loss of fingers or hand.

6. Blades must be OFF except when cutting grass.

Set blades in highest position when mowing over

rough ground.

7. Keep hands and feet away from rotating blades

underneath deck. DO NOT place foot on ground

while BLADES are ON or machine is in motion.

8. DO NOT operate machine without entire grass

catcher or guards in place and working. DO NOT

point discharge at people, passing cars, windows or

doors.

9. Slow down before turning.

10. Watch out for traffic when near or crossing roadways.

11. STOP engine immediately after striking an obstruc-

tion. Inspect machine and repair damage before

resuming operation.

12. Operate machine only in daylight or with good artifi-

cial light.

13. Move joystick (if equipped) SLOWLY to maintain con-

trol during speed and directional changes.

14. Exercise CAUTION when pulling loads. Limit loads

to those you can safely control and attach loads to

hitch plate as specified with attachment instructions.

15. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control. When tow-

ing, travel slowly and allow extra distance to stop.

16. DO NOT operate engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly

poison.

17. DO NOT discharge material against a wall or obstruc-

tion. Material may ricochet back towards the operator.

18. Only use accessories approved by the manufacturer.

See manufacturer’s instructions for proper operation

and installation of accessories.

Emissions

1. Engine exhaust from this product contains chemi-

cals known, in certain quantities, to cause cancer,

birth defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period and

Air Index information on the engine emissions label.

Ignition System

1. This spark ignition system complies with Canadian

Standard ICES-002.

8

Not for

Reproduction

Towing

1. Tow only with a machine that has a hitch designed for

towing. DO NOT attach towed equipment except at

the hitch point.

2. Follow the manufacturer’s recommendation for weight

limits for towed equipment and towing on slopes.

3. DO NOT allow children or others on towed equip-

ment.

4. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

Maintenance

1. DO NOT store machine or fuel container inside where

fumes may reach an open flame, spark or pilot light

such as in a water heater, furnace, clothes dryer or

other gas appliance. Allow engine to cool before

storing machine in an enclosure. Store fuel container

out of the reach of children in a well ventilated, unoc-

cupied building.

2. Keep engine free of grass, leaves or excess grease

to reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved

container outdoors and away from open flame.

4. Check brakes frequently; adjust, repair or replace as

needed.

5. Keep all bolts, nuts and screws properly tight. Check

that all cotter pins are in proper position.

Maintenance

(Continued From Previous Column)

6. Always provide adequate ventilation when running

engine. Exhaust gases contain carbon monoxide, an

odorless and deadly poison.

7. Disconnect negative (black) cable from battery before

performing maintenance or service. Cranking engine

could cause injury.

8. DO NOT work under machine without safety blocks.

9. Service engine and make adjustments only when

engine is stopped. Remove spark plug wire(s) from

spark plug(s) and secure wire(s) away from spark

plug(s).

10. DO NOT change engine governor speed settings or

overspeed engine.

11. Lubricate machine at intervals specified in manual to

prevent controls from binding.

12. Mower blades are sharp and can cut. Wrap the

blades or wear heavy leather gloves and use

CAUTION when handling them.

13. DO NOT test for spark by grounding spark plug next

to spark plug hole; spark plug could ignite gas exiting

engine.

14. Have machine serviced by an authorized dealer at

least once a year and have the dealer install any new

safety devices.

15. Maintain or replace safety and instruction labels as

necessary.

16. Use only factory authorized replacement parts or like

parts when making repairs.

WARNING

Grass Catcher bags used on this product are made of

woven fabric, and are subject to deterioration and wear

during normal usage. Check condition of bags before

each use. Immediately replace worn or damaged catch-

er bags with only bags recommended by the manufac-

turer. The Grass Catcher is optional equipment on some

models.

WARNING

Battery posts, terminals and related accessories contain

lead and lead compounds, chemicals known to the

State of California to cause cancer and birth defects or

other reproductive harm. Wash hands after handling.

WARNING

Engine exhaust, some of its constituents, and certain

vehicle components contain or emit chemicals known to

the State of California to cause cancer or other repro-

ductive harm.

9

en

Not for

Reproduction

WARNING: To avoid serious injury, operate your unit up and

down the face of slopes, never across the face. Do not operate

on slopes greater than 10 degrees. Make turns gradually to

prevent tipping or loss of control. Exercise extreme caution

when changing direction on slopes. Braking may be affected by

attachments. Reduce speed on slopes.

1. Fold this page along dotted line indicated above.

2. Hold page before you so that its left edge is vertically parallel to a tree

trunk or other upright structure.

3. Sight across the fold in the direction of hill slope you want to measure.

4. Compare the angle of the fold with the slope of the hill.

ONLY RIDE UP AND DOWN HILL,

NOT ACROSS HILL

F

O

L

D

A

LON

G

D

OT

TED LI

N

E

THIS IS A

10 DEGREE SLOPE

10 DEGREES MAX.

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

10

Not for

Reproduction

Safety and Instructional Decals

All DANGER, WARNING, CAUTION and instructional

messages on your rider and mower should be carefully

read and obeyed. Personal bodily injury can result when

these instructions are not followed. The information is for

your safety and it is important! The safety decals below

are on your rider and mower.

If any of these decals are lost or damaged, replace them

at once. See your local dealer for replacements.

These decals are easily applied and will act as a con-

stant visual reminder to you, and others who may use the

equipment, to follow the safety instructions necessary for

safe, effective operation.

Decal, Warning

Part No. 1755607

Decal, Warning

Part No. 1755608

Decal, Danger

Part No. 1755606

Decal, Danger

Part No. 7101665

DANGER

Amputation and thrown objects hazard

Keep hands and feet

away from deck.

Do not operate mower

unless discharge chute

or entire grass catcher

is in its proper place.

7101665

Decal, Warning

Part No. 1734273

Decal, Caution

Part No. 7104393

11

en

Not for

Reproduction

12

Safety and Instructional Decals (ANSI

Export Models)

Operating Instructions,

Part No. 1750631

1. WARNING: Read and understand the Operator’s Man-

ual before using this machine. Know the location and

function of all controls. Do not operate this machine

unless you are trained.

2. DANGER - LOSS OF TRACTION, SLIDING, STEER-

ING AND CONTROL ON SLOPES HAZARD: If ma-

chine stops forward motion or starts sliding on a slope,

stop the blades and drive slowly off the slope.

3. DANGER: FIRE HAZARD: Keep unit free of grass,

leaves and excess oil. Do not add fuel while engine

is hot or running. Stop engine, remove key and allow to

cool for at least 3 minutes prior to adding fuel. Do not

add fuel indoors, in an enclosed trailer, garage or other

enclosed areas. Clean up spilled fuel. Do not smoke

while operating this machine.

4. DANGER - TIPPING AND SLIPPING HAZARD: Mow

up and down slopes not across. Do not operate on

slopes over 10 degrees. Avoid sudden and sharp (fast)

turns while on slopes.

5. DANGER - AMPUTATION AND DISMEMBERMENT

HAZARD: To avoid injury from rotating blades and mov-

ing parts, keep safety devices (guards, shields and

switches) in place and working.

6. Do not mow when children or others are around. Never

carry riders especially children even with the blades off.

Do not mow in reverse unless absolutely necessary.

Look down and behind – before and while backing.

7. Consult technical literature before performing technical

repairs or maintenance. When leaving the machine,

shutoff engine, set the parking brake to the lock position

and remove the ignition key.

8. Keep by-standers and children a safe distance away.

Remove objects that can be thrown by the blade. Do not

mow without discharge chute in place.

9. Do not mow without discharge chute or entire grass

catcher in place.

10. To avoid injury from rotating blades, stay clear of deck

edge and keep others away.

Danger, Amputation and

Thrown Objects Hazard,

Part No. 5102420

Danger, Thrown Objects

Hazard, Part No. 5102457

9

10

1

2

5

6

7

8

3

4

Not for

Reproduction

13

en

Decal, Control Panel,

L.H.

Part No. 7104232

7104232

Decal, Control Panel,

R.H.

Part No. 7104233

7104233

Decal, Ground

Speed Lever, L.H.

Part No. 7104226

7104226

Decal, Ground

Speed Lever, R.H.

Part No. 7104227

7104227

Decal, Transmission

Release

Part No. 7104231

7104231

Decal, Weight Limit

Part No. 7101940

Safety Interlock System Tests

This unit is equipped with a Safety Interlock System.

Do not attempt to bypass or tamper with the switches/

devices.

TEST 1 — ENGINE SHOULD NOT CRANK IF:

• PTO switch is engaged, OR

• Parking brake is disengaged, OR

• Ground speed levers are not locked in their START/

PARK positions.

TEST 2 — ENGINE SHOULD CRANK IF:

• PTO switch is NOT engaged, AND

• Parking brake is engaged, AND

• Ground speed levers are locked into their

START/PARK positions.

TEST 3 — ENGINE SHOULD SHUT OFF IF:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with parking brake dis-

enaged, OR

• Operator rises off seat with ground speed levers not

locked in their START/PARK positions.

TEST 4 — CHECK MOWER BLADE STOPPING TIME

The mower blades and mower drive belt should come

to a complete stop within five seconds after the electric

PTO switch is turned off. If mower drive belt does not

stop within five seconds, see your dealer.

NOTE: Once the engine has stopped, the PTO switch

must be turned off, the parking brake must be engaged,

and the ground speed levers must be locked in their

START/PARK positions in order to start the engine.

WARNING

If the unit does not pass a safety test, do not operate

it. See an authorized dealer.

Decal, Control Panel,

L.H. (w/Choke)

Part No. 1756189

1756189

Not for

Reproduction

Features and Controls

Ground Speed Levers

These levers control the ground speed and direc-

tion of the rider. The left lever controls the left rear drive

wheel and the right controls the right rear drive wheel.

Moving a lever forward increases the FORWARD speed

of the associated wheel, and pulling back on a lever

increases the REVERSE speed.

The further a lever is moved away from the neutral posi-

tion the faster the drive wheel will turn.

See the Operation section for steering instructions.

Engine Speed / Choke Control

(Briggs & Stratton Engines)

Move the engine speed / choke control to the FAST

position to increase engine speed, and to the SLOW

position to decrease engine speed. Move the engine

speed / choke control past the FAST position to the

CHOKE position to start a cold engine. A warm engine

may not require choking.

NOTE: Always operate the rider with the engine speed

control in the FAST position.

Control Functions

The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing

require the combined use of several controls applied in specific sequences. To learn what combination and sequence

of controls to use for various tasks see the Operation section.

14

Not for

Reproduction

15

en

Engine Speed Control

(Kawasaki Engines)

Move the engine speed control to the FAST position to

increase engine speed, and to the SLOW position to

decrease engine speed.

NOTE: Always operate the rider with the engine speed

control in the FAST position.

Choke Control

(Kawasaki Engines)

Move the choke control to the CHOKE position to start a

cold engine. A warm engine may not require choking.

Ignition Switch

The ignition switch starts and stops the engine; it

has three positions:

OFF Stops the engine and shuts off the

electrical system.

RUN Allows the engine to run and powers the

electrical system.

START Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN posi-

tion with the engine stopped–this drains the battery.

PTO Switch

The PTO (Power Take-Off) switch engages and

disengages the mower blade clutch. To engage the PTO,

pull UP on the switch. Push DOWN to disengage. Note

that the operator must be seated firmly in the rider seat

for the PTO to function.

Transmission Release Levers

The transmission release levers deactivate the

transmissions so that the unit can be pushed by hand

(see Pushing the Unit by Hand).

Seat Adjustment Lever

The seat can be adjusted forward and backward

(see Seat Adjustments).

Fuel Tank Cap

To remove the cap, turn counterclockwise.

Mower Cutting Height Adjustment

Switch

The mower cutting height is adjustable between 1.5”

(3,8 cm) and 4.0” (10,0 cm). See Cutting Height

Adjustment.

Parking Brake

Moving the parking brake lever forward and to the

right engages the parking brake. Moving the lever to the

left and back disengages the brake.

Not for

Reproduction

16

Operation

General Operating Safety

Before first time operation:

• Be sure to read all information in the Operator Safety

section before attempting to operate this rider and

mower.

• Become familiar with all of the controls and how to

stop the unit.

• Drive in an open area without mowing to become

accustomed to driving the unit.

Checks Before Starting

• Check that the crankcase is filled to full mark on dip-

stick (A, Figure 1 - located under the engine cover on

some models). See the engine owner’s manual for

instructions and oil recommendations.

• Make sure all nuts, bolts, screws and pins are in

place and secure.

• Adjust the seat position (B), and make certain you

can reach all controls from the operator’s position.

• Fill the fuel tank (C) with fresh fuel. Refer to the

engine owner’s manual for fuel recommendations.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any reason,

lock the ground speed levers in the START/PARK

position, engage the parking brake, disengage the

PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, rider and

mower free of grass, leaves and excess grease.

Do not stop or park rider over dry leaves, grass or

combustible materials.

Gasoline is highly flammable and must be handled

with care. Never fill the tank when the engine is still

hot from recent operation. Do not allow open flame,

smoking or matches in the area. Avoid over-filling and

wipe up any spills.

WARNING

Never operate on slopes greater than 18 percent

(10°).

Select slow ground speed before driving onto a slope.

Use extra caution when operating on slopes with a

rear-mounted grass catcher.

Mow up and down slopes, not across the face, use

caution when changing directions and DO NOT

START OR STOP ON SLOPE.

Do not load this zero-turn rider on a trailer or truck

using two separate ramps. Only use a single ramp

that is at least one foot wider than the width of the

rear wheels of this rider. This rider has a zero turning

radius and the rear wheels could fall off the ramps,

or the rider could tip over injuring the operator or

bystanders.

WARNING

If you do not understand how a specific control

functions, or have not yet thoroughly read the Features

and Controls section, do so now. Do NOT attempt to

operate the rider without first becoming familiar with

the location and function of ALL controls.

Figure 1. Pre-Start Checks

B

C

A

Not for

Reproduction

17

en

Starting the Engine

1. While sitting in the operator’s seat, make sure the

PTO switch is disengaged, the parking brake is

engaged, and the ground speed levers are locked in

the START/PARK position.

2. Briggs Engines: Set the engine speed / choke con-

trol to the CHOKE position.

Kawasaki Engines: Set the engine speed control to

the FAST position, and engage the choke control.

NOTE: A warm engine may not require choking.

3. Insert the key into the ignition switch and turn it to

START.

4. After the engine starts,

Briggs Engines: Move the engine speed / choke

control back to the FAST position.

Kawasaki Engines: Disengage the choke control.

Warm up the engine by running it for at least a minute

before engaging the PTO switch or driving the rider.

5. After warming the engine, ALWAYS operate the rider

at FULL ENGINE SPEED when mowing.

In the event of an emergency the engine can be

stopped by simply turning the ignition switch to

STOP. Use this method only in emergency situations.

For normal engine shut down follow the procedure given

in Stopping the Rider and Engine.

Stopping the Rider and Engine

1. Return the ground speed levers to the middle (or

neutral ‘N’) position to stop rider movement. Pivot the

levers outward to lock them in the START/PARK posi-

tion.

2. Disengage the PTO by pushing down on the PTO

switch.

3. Engage the parking brake by moving the parking

brake lever forward and to the right.

4. Move the engine speed control to the SLOW position

and turn the ignition key to OFF. Remove the key.

Mowing

1. Make sure the PTO switch is disengaged, the parking

brake is engaged, the ground speed levers are locked

in their START/PARK positions, and the operator is in

the seat.

2. Start the engine (see Starting the Engine).

3. Set the mower cutting height (see Cutting Height

Adjustment).

4. Set the engine speed control to FAST.

5. Disengage the parking brake.

6. Engage the PTO by pulling up on the switch.

7. Pivot the ground speed levers in from the START/

PARK position to the neutral ‘N’ position.

8. Begin mowing. See Operator Safety for tips on safe

mowing practices.

9. When finished, shut off the PTO.

10. Stop the engine (see Stopping the Rider and

Engine).

Pushing the Rider by Hand

1. Disengage the PTO, engage the parking brake, lock

the ground speed levers into their START/PARK posi-

tions, turn the ignition OFF, remove the key, and wait

for all moving parts to stop.

2. To disengage the transmissions, pull the roll release

rods (A, Figure 2), located on either side of the

engine, up into the PUSH position.

3. Disengage the parking brake.

The rider can now be pushed by hand.

4. After moving the rider, re-engage the transmissions

by pushing the roll release rods back down to the

DRIVE position.

DO NOT TOW RIDER

Towing the unit will cause transmission dam-

age. Do not use another vehicle to push or

pull this unit.

Figure 2. Roll Release Components (On Each Side)

WARNING

DO NOT disengage the transmissions and coast

down slopes. DO NOT use Roll Release to disengage

the transmissions unless machine motion can be

controlled and engine is off.

A

Not for

Reproduction

Basic Driving

Figure 4. Forward Travel

Forward

Travel

Figure 5. Reverse Travel

Reverse

Travel

Smooth Travel

The ground speed levers

of the zero turn rider are

responsive.

The BEST method of

handling the ground

speed levers is in three

steps — as shown in

Figure 3.

FIRST place your hands

onto the levers as

shown.

SECOND, to go forward

gradually push the levers

forward with your palms.

THIRD, to speed up,

move the levers farther

forward. To slow down

smoothly, slowly move

the levers toward neu-

tral.

Figure 3. Move Ground

Speed Levers Gradually

Forward Travel Practice

Gradually move both ground speed levers — evenly

FORWARD from neutral. Slow down and repeat.

Straight forward travel takes practice. If necessary, top

speed can be balance-adjusted — see Speed Balancing

Adjustment section.

Reverse Travel Practice

LOOK DOWN & BEHIND, then gradually move both

ground speed levers evenly BACK from neutral. Slow

down and repeat.

Practice backing up for several minutes before attempt-

ing to do so near objects. The rider turns as sharply in

reverse as when going forward, and backing up straight

takes practice.

Zero Turn

Driving Practice

The ground speed levers of the zero turn rider are

responsive, and learning to gain a smooth and efficient

control of the rider’s forward, reverse, and turning move-

ments will take some practice.

Spending some time going through the maneuvers shown

and becoming familiar with how the unit accelerates, trav-

els, and steers — before you begin mowing — is abso-

lutely essential to getting the most out of the zero turn

rider.

Locate a smooth, flat area of your lawn — one with

plenty of room to maneuver. (Clear the area of objects,

people and animals before you begin.) Operate the

unit at mid-engine speed during this practice session

(ALWAYS operate at full engine speed when mowing),

and turn slowly to prevent tire slippage and damage to

your lawn.

We suggest you begin with the Smooth Travel proce-

dure to the right, and then advance through the forward,

reverse, and turning maneuvers.

18

Not for

Reproduction

19

en

Advanced Driving

Executing an End-Of-Row Zero

Turn

Your zero turn rider’s unique ability to turn in

place allows you to turn around at the end of

a cutting row rather than having to stop and

Y-turn before starting a new row.

For example, to execute a right end-of row

zero turn:

1. Slow down at the end of the row.

2. Move the LEFT ground speed lever

forward slightly while moving the

RIGHT ground speed lever back to center

and then slightly back from center.

3. Begin mowing forward again.

This technique turns the rider RIGHT and

slightly overlaps the row just cut — eliminating

the need to back up and re-cut missed grass.

As you become more familiar and experi-

enced with operating the zero turn rider, you

will learn more maneuvers that will make your

mowing time easier and more enjoyable.

Remember, the more you practice, the better

your control of the rider will be!

Executing

Turns

Figure 6. Turning Around a Corner

Figure 7. Turning in Place

Turning

In-Place

Figure 8. Executing an End-Of-Row Turn

Practice Turning In Place

To turn in place, “zero turn,” gradually move one ground

speed lever forward from neutral and one lever back from

neutral simultaneously. Repeat several times.

Changing the amount each lever is pulled — forward or

back, changes the “pivot point” you turn on.

Practice Turning Around a Corner

While traveling forward allow one lever to gradually return

back toward neutral. Repeat several times.

To prevent pivoting directly on thetire tread, it is best to

keep both wheels going at least slightly forward.

Not for

Reproduction

Figure 9. Trailer Weight Recommendations

A

B

Attaching a Trailer

The maximum weight of a towed trailer should be less

than 200 lbs (91 kg). Secure the trailer with an appropri-

ately sized clevis pin (A, Figure 9) and clip (B).

Excessive towed loads can cause loss of traction and

loss of control on slopes. Reduce towed weight when

operating on slopes. The surface being driven on greatly

impacts traction and stability. Wet or slippery surfaces

can greatly reduce traction and the ability to stop or turn.

Carefully evaluate the surface conditions before oper-

ating the unit and trailer, and never operate on slopes

greater than 10°. See Protection Against Tipovers and

Towing in the Operator Safety section of this manual.

3’6”

(1m)

20’ (6m)

20

La page charge ...

Simplicity 2691161-00 Manuel utilisateur

Ce manuel convient également à

Simplicity 2691161-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents