SEMES SSD-100 Smoke and Temperature Detection Manuel utilisateur
- Taper
- Manuel utilisateur
Home » SEMES » SEMES SSD-100 Smoke and Temperature Detection User Manual
Contents
1 SEMES SSD-100 Smoke and Temperature
Detection
2 Product Overview
3 Package Content
4 Product Function and How To Use
5 General Operation (Mode Description)
6 Maintenance mode
7 Installation instruction
8 Specification
9 Warning Information
10 Manufacturer and Distributor
11 Documents / Resources
12 Related Posts
SEMES SSD-100 Smoke and Temperature Detection
SEMES SSD-100 Smoke and Temperature Detection User
Manual
Manuals+ — User Manuals Simplified.
Product Overview
It is a stand alone smoke and temperature detector designed to be used in various industrial production lines such
as distribution boards.
1. Smoke Detection Method (Light Scattering) Alarm function to notify of fire by detecting smoke caused by fire
2. Stand Alone alarm Detecting Smoke and sounds a Smoke alarm to notify people of the occurrence of a fire
3. Built-in Temperature sensor (PT100)
Package Content
Product Function and How To Use
Unit Layout and Function
No Description Function
1 Alarm Buzzer Alarm Sounds in case of Fire (1second on/1second off)
2
Reset Switch / LED Turn alarm sounds off or operation testing Status display LED
3 Screw Cap Screw Cap
4
Input / Output Port
DC 24V Voltage input.
Relay input / output & temperature sensor_PT100 input / output
Status Relay Contact Operating
Power on B contact Normal
Power off A contact B à A contact
Smoke Alarm On A contact B à A contact
Reset Alarm sound B contact A à B contact
LED Operation
LED Indication Status Description
Green LED ON Normal Status
Red LED Blinking Smoke Detection (Red LED 1second on/1second off)
Red LED ON Short Key : Red LED On until Alarm sound Off Long Key : maintenance mode
General Operation (Mode Description)
1. (Smoke monitoring mode) Once power is applied properly with correct power connection, Green LED will be
ON and Relay is connected to B contact.
2. (Smoke detection mode) When device detect smoke by fire, Red LED will be blinking and sounds alarm.
3. Operator click the Reset switch in order to reset device which is in Smoke detection mode,. Alarm sounds will
be OFF and Red LED will be ON until device come to smoke monitoring mode back. In Smoke monitoring
mode, LED will change to Green color
Maintenance mode
1. Push reset switch for 3 seconds in Smoke monitoring mode, Red LED will be On and alarm sounds.
2. Once click reset switch again, Alarm sound will be off and LED will be changed green color.
Installation instruction
How to install
Input/output pin-map
No name Connection
1 24V DC24V connect (Less than 30 m)
2 GND DC GND connect
3 FG Ground
4 R1 Relay input
5 R2 Relay B contact
6 PT1 PT100 A terminal
7 PT2 PT100 B terminal
Caution
1. When wiring to the terminal block, please be careful not to allow foreign objects such as dust or wire sheath to
enter the connection terminals and the inside of the product.
2. When mounting and wiring, make sure to disconnect the external power source.
3. Please use device in the prescribed temperature range. Otherwise, the product may malfunction and break.
4. Please use within the rated voltage and current ranges. When device used outside of prescribed range. the
product may malfunction and break.
5. Please read the product manual carefully and check the product rating, connection diagram, appearance
specifications, etc.
6. This product is an optical smoke detector that avoids dusty places, areas affected by wind, and places where
the lighting shines directly on the product, etc., and please carefully monitor the installation environment and
install and use it.
Use by installing at a distance of 60 cm from the wall.
Install and use in a place that is not affected by air conditioners and fans.
Install and use at a distance of at least 1 meter from the lights
7. In the event of an abnormality in the product, do not arbitrarily disassemble it and exchange it at the place of
purchase.
8. When using the product, please take care not to get debris around the product and on the exterior of the smoke
chamber in the product. (This causes malfunctions.)
9. Test in check mode every 1 month to make sure there are no abnormalities in the product.
Specification
No Category Description
1 Model Number SSD-100
2 Model Type DC 24V, Photo-electric type2, non-waterproof
3 Power DC 24V / current 50mA
4 Operating condition -10℃~60℃ / Humidity 10%~ less than 90%
5 Alarm sounds Bigger than 85dB
6 Detection Method Photo-electric (Light-scattering)
7 Temperature sensor PT100
8 Dimension / Weight 90.0 x 102 x 35.7 (mm) / 130g
9 Certification CE, FCC, KC , KFI Report.
10 Intended use environment Industry
Warning Information
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Manufacturer and Distributor
Manufacturer SEMES / Republic of Korea
Distributor Bridge Builder / 010-2740-5634
After Service 02-2699-7536~7
Address 77, 4sandan 5-gil, Jiksan-eup, Seobuk-gu, Cheonan-si, Chungcheongna
m-do, Republic of Korea
Documents / Resources
-
1
-
2
-
3
-
4
-
5
-
6
-
7
