DOODLe labs ACM-DB-2M Mode d'emploi

ACM-DB-2M
Marque
DOODLe labs
Modèle
ACM-DB-2M
Catégorie
Points d'accès WLAN
Taper
Mode d'emploi
ACM-DB-2M
Rugged/Military grade 2.4/ 2x2 MIMO Wi-Fi® Radio Transceivers
Features
•Qualcomm-Atheros QCA9890-BR4B Chipset with Extended Temperature Range
•Up to 1.3 Gbps Throughput with 3x3 MIMO Technology
•Calibrated High Power 2.4 GHz (29 dBm) afor Extended Range
•802.11 Dynamic Frequency Selection (DFS) in AP and Client mode
•Supported by OpenWRT and Ath10k Open-Source Driver
•MiniPCIE Interface
Installation and Usage
The ACM-DB-2M has been FCC certified for indoor usage with Superbat 3-dBi rubber-duck antennas
(WA2-1321-S02SP1-030 in the 5-GHz bands, and WA2-995-S02SP1-030 antennas in the 2.4GHz band). The
ACM-DB-3 mates with a standard PCIE-mini slot and integrates with the Ath10k software driver which is pre-
installed in Linux-based systems.
TECHNICAL SPECIFICATIONS
Model No.
ACM-DB-2M(Rugged/Military Applications, 802.11ac)
MAC Chipset
QCA9890-BR4B with Extended Temperature range for Outdoor and Rugged models)
Software Support
Open Source Linux Driver
ath10k
OpenWRT (Wireless Router/Linux OS)
Center Frequency Range
2.412 GHz ~ 2.484 GHz
This varies by the regulatory domain
Channel Bandwidth/(No. of Non-
overlapping Channels)*
20/(27), 40/(13) and 80/(6) MHz channels (5.x GHz)
20/(3), and 40/(1) MHz channels (2.4 GHz)
Radio Modulation (Auto Adjust)
BPSK, QPSK, 16 QAM, 64 QAM and 256 QAM (5.x GHz – 11ac models)
CCK, BPSK, QPSK, 16 QAM, and 64 QAM (2.4 GHz – 11ac models)
Data Rates Supported
802.11n: MCS0-23 (5.x and 2.4 GHz)
802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps (2.4 GHz)
802.11ac Wave 1 Capabilities
●Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx), Maximal ratio combining
(MRC), Cyclic shift diversity (CSD), Frame aggregation, block ACK, 802.11e compatible
bursting, Spatial multiplexing, cyclic-delay diversity (CDD), low-density parity check (LDPC),
Space Time Block Code (STBC)
●Phy data rates up to 1.3 Gbps (80 MHz channel)
Operating Modes
AP, STA and Adhoc modes to implement Point to Point, Point to multi Point, and Mesh
networks
MAC Protocol
TDD with Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)
Wireless Error Correction
FEC, ARQ
Wireless Data Security
128 bit AES, WEP, TKIP and WAPI hardware encryption. Support for IEEE 802.11d, e, h, i, k,
r, v, w and time stamp standards
FIPS Certification
Loop back mode to facilitate FIPS AES certification, Small packet size (96 bytes) in AES
encryption at full packet rate
Tx/Rx Specification
Data Rate
Radio
Modulation
Throughput**
Mbps
(Cabled Test
Setup)
Max Tx Power
(± 2 dBm)
3 Antennas
Rx Sensitivity
(± 2 dBm)
3 Antennas
2.4 GHz (20 MHz Channel)
802.11b, Single Stream, STBC
1 Mbps
CCK
0.8
29
-100
802.11g, Single Stream, STBC
6 Mbps
BPSK
5.5
29
-98
802.11g, Single Stream, STBC
24 Mbps
16 QAM
18
29
-90
802.11g, Single Stream, STBC
36 Mbps
16 QAM
24
27
-87
802.11g, Single Stream, STBC
48 Mbps
64 QAM
31
26
-84
802.11g, Single Stream, STBC
54 Mbps
64 QAM
32
26
-82
802.11n, HT20, 3 Streams
MCS16
BPSK
18
29
-92
802.11n, HT20, 3 Streams
MCS18
QPSK
54
29
-86
802.11n, HT20, 3 Streams
MCS20
16QAM
108
27
-79
802.11n, HT20, 3 Streams
MCS22
64 QAM
162
24
-75
802.11n, HT20, 3 Streams
MCS23
64QAM
189
24
-74
2.4 GHz (40 MHz Channel)
802.11n, HT40, 3 Streams
MCS16
BPSK
36
29
-87
802.11n, HT40, 3 Streams
MCS18
QPSK
108
29
-80
802.11n, HT40, 3 Streams
MCS20
16QAM
216
26
-74
802.11n, HT40, 3 Streams
MCS22
64 QAM
470
24
-70
802.11n, HT40, 3 Streams
MCS23
64QAM
486
23
-68
* It is advantageous to use the smallest Channel Bandwidth that can support the Throughput requirements. Smaller Bandwidths
provide more channels to choose and help avoid interference issues. The system’s SNR is higher at smaller Channel Bandwidths
and Range is longer.
** Throughput of a wireless link depends on many environmental parameters. Here the bench measurement results are shown to
give an indication of the real life performance of Doodle Labs modules. These results are lower than the theoretical values
published in most of the literature. They do not include distance related derating.
Antenna Signal Strength
-50 to -90 dBm (Recommended), Absolute Maximum=+12 dBm
Antenna port isolation for
concurrent operation
Up to +5 dBm signal strength for 2.4 GHz signal without degrading 5.x GHz operation
Integrated Antenna Port
Protection
>12 KV (Human Body Model) for Outdoor and Rugged models (ACO/ACM-DB-3 and NO/NM-
DB-3)
Receiver LNA Gain
>12 dB
Receiver Adjacent Channel
Rejection (ACR)
>28 dB @6 Mbps, 13 dB @54 Mbps, 3 dB @ VHT80, MCS9
Receiver Next to Adjacent
Channel Rejection (ALCR)
>40 dB
Receive chain Noise Figure
+5 dB
Transmitter Adjacent Channel
Leakage power Ratio (ACLR)
Min 45 dB (Fc ± ChBW)
Transmitter Spurious Emission
Suppression
-40 dBc (Minimum)
RF Power control by Driver
In 0.5 dBm steps. Accuracy of power calibration ±2 dBm
RF Hardware Disable
Pin 20 of miniPCI-E interface. (Required for FAA compliance)
Control for External Power Amp
Available as an optional configuration
Spectral Analysis
8 bit resolution spectral FFTs available for software analysis
PHYSICAL, ENVIRONMENTAL AND OTHER SPECIFICATIONS
Antenna Ports
3 Ports (50 Ohms) with MMCX connectors.
Optional configuration with U.FL connectors available on request
Host Interface
miniPCI-Express 1.2 Standard
Host CPU Board
Any CPU board with Industry standard miniPCI-Express interface with minimum 6 mm
connector height
Operating Voltage
3.3 Volts from miniPCI-Express connector
Power Consumption
5W @ Max power, in continuous data transfer mode on all 3 chains
3.5W @ 25 dBm power, in continuous data transfer mode on all 3 chains
2.5W @ 20 dBm power (ETSI max), in continuous data transfer mode on all 3 chains
0.9W in continuous data receive mode
250 mW in Sleep mode
Shield case temperature range
(Operating)
0°C to +60°C (Enterprise/Indoor “*E-DB-3” models)
-40°C to +60°C (Outdoor “*O-DB-3” models)
-40°C to +80°C (Rugged “*M-DB-3” models)
The System’s thermal design should ensure that the transceiver’s case temperature is
maintained within these specifications.
Humidity (Operating)
0% – 95% (Non-condensing)
Dimensions
30 x 50 x 7 mm, 14 grams (Rugged models).
Mechanical drawing and 3D-CAD files available upon request
Regulatory Requirements
Designed and Verified to meet various regulatory requirements. Formal testing and approval
is required based on the Integrator’s particular host platform and antenna type. The Integrator
is also responsible for obtaining all required regulatory approvals in target markets for the
finished product.
FCC ID
2AG87ACM-DB-2M
CE/ETSI
11ac models in AP and Client modes with full DFS – in conformity with all the requirements of
the European Directive 1999/5/EC – EN 301 893 V1.8.1, EN 300 328 V.1.8.1, EN 301 489-1
V1.9.2, EN 301 489-17 V2.2.1, EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011+
A2:2013
Industry Canada (IC)
21411-ACMDB2M
RoHS/WEEE Compliance
Yes. 100% Recyclable/Biodegradable packaging
FCC Statement
FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247
External antenna with gain ANT0: 7dBi, ANT1: 7dBi
FCC Regulatory Compliance:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
If power exceeds the limit and the distance(Over 20cm distance in actual use between the device and user) is compliance
with the requirement
RF Exposure Compliance:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated
with a minimum distance of 20cm between the radiator and any part of your body.
Notice to OEM integrator
If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the
module is installed must also
display a label referring to the enclosed module. The end product shall haves the words “Contains Transmitter Module FCC
ID: 2AG87ACM-DB-2M”.
The device must be professionally installed.
The intended use is generally not for the general public. It is generally for industry/commercial use.
The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not
normally required. The user has no
access to the connector.
Installation must be controlled. Installation requires special training.
Any company of the host device which installs this modular with unlimited modular approval should perform the test of
radiated & conducted emission and spurious emission, etc. according to FCC part 15C: 15.247 and15.209 & 15.207, 15B
Class B requirement, only if the tests result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B Class B
requirement, then the host can be sole legally.
When the module is installed inside another device, the user manual of the hose contain below
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation
Singapore:
Doodle Labs (SG) Pte. Ltd.
150 Kampong Ampat
KA Center, Suite 05-03
Singapore 368324
Tel: +65 6253 0100
USA:
Doodle Labs LLC
2 Mattawang Drive
Somerset, NJ 08873
Tel: +1 862 345 6781
Fax: +65 6353 5564
IC statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic DevelopmentCanada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
This product meets the applicable Industry Canada technical specifications.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences etDéveloppement économique
Canada. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pasproduire de
brouillage,et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme auxCNR d'Innovation,
Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
1)L'appareil ne doit pas produire de brouillage;
2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre lefonctionnement.
Please notice that if the ISED certification number is not visible when the module is installed inside another
device, then theoutside of the device into which
the module is installed o display a label referring to the enclosed module. This exteriorlabel can use wording
such as the following: “Contains IC:21411-ACMDB2M” any similar wording that expresses the same
meaningmay be used.
l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada,
précédé des mots «Contient un module
d'émission », du mot « IC:21411-ACMDB2M» ou d'une formulation similaireexprimant le même sens, comme
suit
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 andcompliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure andcompliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla
conformité à l'expositionde RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la
conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter. This
equipment should be installed and operated with a minimum distance of 20centimeters between the radiator
and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne
ouémetteur. Cet équipementdevrait être installé et actionné avec une distance minimum de 20 centimètres
entre le radiateur et votre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

DOODLe labs ACM-DB-2M Mode d'emploi

ACM-DB-2M
Marque
DOODLe labs
Modèle
ACM-DB-2M
Catégorie
Points d'accès WLAN
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents