VTech TM8112 Manuel utilisateur

VTech
Marque
VTech
Modèle
TM8112
Catégorie
Babyphones
Taper
Manuel utilisateur

Ce manuel convient également à

TM8112
TM8112-2
Digital Audio Monitor with
Glow-on-the-Ceiling Night Light
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
Congratulations
on purchasing your new VTech product.
Before using this product, please read Important safety instructions.
This manual has all the feature operations and troubleshooting necessary to install and operate
your new VTech product. Please review this manual thoroughly to ensure proper installation and
operation of this innovative and feature-rich VTech product.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.
1 set for TM8112
2 sets for TM8112-2
User’s manual
TM8112 TM8112-2
For more support information
S
m
Important safety instructions
The applied nameplate is located at the bottom of the baby
unit’s base.
When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above
2 meters.
4. This product is not a substitute for adult supervision
of the infant. Supervising the infant is the parent’s or
caregiver’s responsibility. This product could cease
operating, and therefore you should not assume it will
continue working properly for any given period of time.
Further, this is not a medical device and should not be
used as such. This product is intended to assist you in
supervising your baby.
5. Do not use this product near water. For example, do not
use it next to a bath tub, wash bowl, kitchen sink, laundry
tub or swimming pool, or in a wet basement or shower.
6. CAUTION: Use only the battery provided. There may be
a risk of explosion if a wrong type of battery is used for
the parent unit. The battery cannot be subjected to high
or low extreme temperature and low air pressure at high
altitude during use, storage or transportation. Disposal of
battery into fire or a hot oven, or mechanically crushing or
cutting or the battery can result in an explosion. Leaving
the battery in an extremely high temperature surrounding
environment can result in an explosion or the leakage of
flammable liquid of gas. Battery subjected to extremely
low air pressure may result in an explosion or the leakage
of flammable liquid or gas. Dispose of used battery
according to the information in The RBRC seal.
7. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Power adapter information:
Output: 6V DC 400mA
VTech Telecommunications Ltd.
Model: VT05UUS06040
Rechargeable battery information:
2.4V 400mAh Ni-MH
Yiyang Corun Battery Co. Ltd
Model: NI-MHAAA400×2-FF
GPI International Ltd.
Model: VTRHC043C040
8. The power adapters are intended to be correctly oriented
in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
9. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
10. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth
for cleaning.
11. Unplug the power cords before replacing battery.
12. Do not cut off the power adapters to replace them with
other plugs, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
14. This product should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supply in your home,
consult your dealer or local power company.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf,
stand or other unstable surfaces.
17. This product should not be placed in any area where
proper ventilation is not provided. Slots and openings
in the back or bottom of this product are provided for
ventilation. To protect them from overheating, these
openings must not be blocked by placing the product
on a soft surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or heat
register.
18. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of any
kind on the product.
19. To reduce the risk of electric shock, do not disassemble
this product, but take it to an authorized service facility.
Opening or removing parts of the product other than
specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can
cause electric shock when the product is subsequently
used.
20. You should test the sound reception every time you turn
on the units or move one of the components.
21. Periodically examine all components for damage.
22. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless
telephones, etc. To protect your privacy, make sure the
product has never been used before purchase, reset
the baby monitor periodically by powering off and then
powering on the units, and power off the baby monitor
if you will not use it for some time.
23. Children should be supervised to ensure that they do not
play with the product.
24. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 32oF
and 104oF.
2. Do not expose the product to extreme cold, heat or
direct sunlight. Do not put the product close to a heating
source.
3. Batteries should not be exposed to excessive heat such as
bright sunshine or fire.
4. Warning—Strangulation Hazard—
Children have STRANGLED in cords. Keep
this cord out of the reach of children (more
than 3 ft (0.9m) away). Do not remove this
tag.
5. Never place the baby unit(s) inside the baby’s crib or
playpen. Never cover the baby unit(s) or parent unit with
anything such as a towel or a blanket.
6. Other electronic products may cause interference
with your baby monitor. Try installing your baby
monitor as far away from these electronic devices
as possible: wireless routers, radios, cellular
telephones, intercoms, room monitors, televisions,
personal computers, kitchen appliances and cordless
telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and
implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the
pacemaker.
• Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and
according to the instructions in this user’s manual, the product
is safe to be used based on scientific evidence available today.
What’s in the box
Quick Start Guide
NOTESNOTE
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time, disconnect and remove the battery
to prevent possible leakage.
1 Install parent unit battery
Battery Pack / Bloc-piles :
BT183342/BT283342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR0920
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
THIS SIDE UP
:
AVERTISSEMENT :
TTERIES.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
:
AVERTISSEMENT :
TTERIES.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
1
2
3
4
Connect the baby monitor
Notes
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to a switch-controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are
not designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-
the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of
children.
When you have installed the parent unit battery and connected it to power for the first
time or after a power outage, the parent unit powers on automatically.
Notes
• The parent unit battery is fully charged after 16 hours of continuous charging.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
• The standby time varies depending on the volume level you set, your actual use and the age of
battery.
Charge the parent unit
4
2 Connect and charge the units
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
3 Power on the baby monitor
Press to power on the baby unit.
The power indicator LED light turns
on. Press and hold again to power
off the baby unit. The power indicator
LED light turns off.
Press and hold to power on the
parent unit. The power indicator LED
light turns on. Press and hold again
to power off the parent unit. The
power indicator LED light turns off.
4 Status check
5 Positioning the baby monitor
> 3ft (1m)
> 6.5ft (2m)
6.5ft (2m)
<
Caution
• Keep the baby unit out of the reach
of your baby. Never place or mount
the baby unit inside the baby’s cot or
playpen.
You may test the baby monitor before initial use, and at regular times thereafter.
1. Make sure your baby unit and parent unit are on.
2. Speak towards the microphone of the baby unit. You will hear the sound at the parent unit,
and see the visual sound indicators light up.
6.5ft (2m)
>
Caution
• For hearing protection, make sure the parent
unit is more than 6.5 ft (2 m) away from the
baby unit. If you experience feedback:
• Move the parent unit further until the
noise stops.
• You can also press on the parent
unit to lower or mute the noise.
Caution
• For hearing protection, make sure the parent unit
is more than 6.5 ft (2 m) away from the baby unit.
If you hear feedback, move the units further apart
until the noise stops.
You can also press on the parent unit to
lower or mute the noise.
Place your baby unit at a location
suitable for glow-on-the-ceiling
night light to project images onto
the ceiling.
UL STD.
62368-1
CERTIFIED TO
CSA STD.
C22.2 NO.62368-1
CONFORMS TO
Specifications are subject to change without notice.
© 2021 VTech Communications, Inc.
All rights reserved. 10/21. TM8112-X_QSG_V1
Basic operation
Adjust speaker volume
The parent unit speaker volume is preset to Level 3 by default, you can adjust it to your
preferred volume level.
• Press to decrease the volume, and to increase the volume.
To mute the speaker volume:
• Press repeatedly until the volume reaches the minimum.
Note
• If you continue to press or when the volume reaches the minimum or maximum
setting, the parent unit will beep twice.
Overview - Baby unit
1Glow-on-the-ceiling night light
projector
2 Glow-on-the-Ceiling Night Light
On/Off
• Press to turn Glow-on-the-Ceiling
Night Light on or off.
3Microphone
4Power LED light
• Light on when the baby unit is on.
• Light off when the baby unit is off.
5 Power On/Off
• Press and hold to power on.
• Press and hold again to power off.
6Power jack
7Speaker
Overview - Parent unit
1Speaker
2 Battery LED light
• Light on when battery is charging.
• Light flashes when battery is low
and needs charging.
• Light off when the parent unit is
running on AC power without
battery installed, or the parent unit
is running on battery only.
3 Power LED light
• Light on when parent unit is
powered on.
• Light off when the parent unit is
powered off.
• Light flashes when there is no link
between baby unit and parent
unit.
4 Power On/Off
• Press and hold to power on.
• Press and hold again to power off.
5 /
• Adjust parent unit speaker volume.
6Visual Sound Indicator
The visual sound indicator shows the
sound level detected by the baby
unit, and the volume level when
setting unit volume.
• Green lights
indicate a moderate sound level
detected by the baby unit.
• Additional red
lights indicate a higher sound level
detected by the baby unit (e.g.
baby crying loudly).
7 Night Light LED light
• Light on when the projector is on.
• Light off when the projector is off.
8 Glow-on-the-Ceiling Night Light
On/Off
• Press to turn Glow-on-the-Ceiling
Night Light on or off.
9Power jack
10 Belt clip
11 Battery compartment cover
10
11
FCC Part 15
This equipment has been tested and found to comply with
the requirements for a Class B digital device under Part 15 of
the Federal Communications Commission (FCC) rules. These
requirements are intended to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
WARNING: Changes or modifications to this equipment not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the
amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the
product. This product has been tested and found to comply
with the FCC criteria. Caution: The baby unit must be installed to
provide a separation distance of at least 20cm from all persons.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
The term ‘’IC:‘’ before the certification/registration number
only signifies that the Industry Canada technical specifications
were met.
This product meets the applicable Innovation, Science and
Economic Development Canada technical specifications.
FCC RF radiation exposure statement
Caution: This baby unit must be installed to provide a separation
distance of at least 20cm from all persons. For body worn
operation, this parent unit has been tested and meets the FCC
RF exposure guidelines. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines. This equipment
complies also with Industry Canada RSS-102 with respect to
Canada’s Health Code 6 for Exposure of Humans to RF Fields.
For cETL compliance only FCC and IC regulations
Mesures de sécurité importantes
La plaque signalétique appliquée est située au bas du socle de
l’unité du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les
risques d’incendie, d’électrocution et de blessures corporelles,
dont ceux qui suivent :
1. Observez toutes les instructions et mises en garde inscrites
sur l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres.
4. Ce produit ne remplace pas la surveillance adulte du
nourrisson. La supervision du nourrisson est la responsabilité
du parent ou de la personne qui s’occupe de l’enfant. Ce
produit pourrait cesser de fonctionner et, par conséquent,
vous ne devriez pas présumer qu’il continuera de fonctionner
correctement pendant une période de temps donnée. De
plus, il ne s’agit pas d’un instrument médical et ne devrait pas
être utilisé comme tel. Ce produit est destiné à vous aider à
superviser votre bébé.
5. N’utilisez pas cet appareil près de l’eau ni de toute autre
source d’humidité, par exemple, près d’une baignoire, cuve
à lessive, évier de cuisine, dans un sous-sol humide ni près
d’une piscine, dans un soussol humide ou une douche.
6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il
existe un risque d’explosion si un autre type de batterie est
utilisé pour l’unité Parents. N’incinérez pas les piles. Celles-ci
risqueraient d’exploser. Jetez les piles usées selon les
renseignements suivant le sceau du RBRC.
7. N’utilisez que les adaptateurs inclus avec ce produit.
L’utilisation d’un adaptateur dont la polarité ou la tension
serait inadéquate risque d’endommager sérieusement le
produit et mettre votre sécurité en péril.
Informations sur les adaptateurs électriques :
Sortie : 6V CC 400mA
VTECH TELECOMMUNICATIONS LTD.
Modèle : VT05UUS06040
Informations sur les piles rechargeables :
2xAAA 2.4V 400mAh Ni-MH
YIYANG CORUN BATTERY CO LTD.
Modèle : NI-MHAAA400×2-FF
GPI INTERNATIONAL LTD.
Modèle : VTRHC043C040
8. Lorsqu’ils sont branchés dans une prise de courant, les
adaptateurs secteur ont été conçus pour être orientés
correctement, soit à la verticale ou au plancher. Les broches
n’ont pas été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici est branché
dans une prise au plafond, sous une table ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT,
la prise de courant doit être installée près du produit, afin
d’assurer une accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant avant de
procéder au nettoyage. N’utilisez pas de nettoyants en
aérosols. Utilisez un chiffon humide pour le nettoyer.
11. Débranchez les cordons d’alimentation avant de remplacer
le bloc-piles.
12. Ne coupez pas les cordons d’alimentation pour remplacer les
fiches, car ceci peut présenter un danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur le cordon
d’alimentation. N’installez pas cet appareil dans un endroit
où l’on risque d’écraser le cordon d’alimentation ou de le
piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur l’étiquette. Si vous ne connaissez
pas le type d’alimentation que vous possédez à votre
domicile, consultez votre marchand ou votre compagnie
locale d’électricité.
15. Ne surchargez pas les prises de courant murales ni les
rallonges électriques.
16. Ne placez pas cet appareil sur un chariot, meuble, trépied,
support de montage ni table chancelants.
17. Les trous et ouvertures du boîtier, situés à l’arrière de
l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour
l’empêcher de surchauffer, ne bloquez sous aucun prétexte
ces ouvertures et n’empêchez pas l’aération adéquate de
l’appareil en le plaçant sur un lit, divan, tapis ou toute autre
surface similaire. De même, ne le positionnez pas à proximité
ni au-dessus d’une source de chaleur ou d’un calorifère. De
plus, ne placez pas l’appareil dans un endroit avant de vous
assurer qu’il y ait une bonne circulation d’air.
18. N’enfoncez jamais d’objets à travers les ouvertures de
cet appareil, car ils pourraient entrer en contact avec
des points de tension dangereux ou causer des courts-
circuits qui peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide dans ce
produit.
19. Afin de réduire les risques d’électrocution, ne démontez
pas cet appareil, mais apportez-le dans un centre de service
autorisé. L’ouverture du boîtier ou le retrait de toutes pièces
que contient cet appareil, à l’exception de l’accès autorisé
à certaines portes ou ouvertures, risque de vous exposer à
des points de tension dangereux ou d’autres dangers. Un
remontage incorrect peut par la suite présenter des risques
d’électrocution.
20. Vous devriez tester la réception chaque fois que vous mettez
l’appareil en fonction.
21. Examinez les composantes afin de vérifier si celles-ci ne sont
pas endommagées.
22. Il existe un très faible risque de perte de confidentialité
avec certains appareils électroniques (autres écoute-bébés,
téléphones sans fils etc.). Pour l’éviter, s’assurer que le produit
n’a jamais été utilisé avant l’achat, réinitialiser l’unité de façon
périodique, éteindre l’écoute-bébé quand il n’est pas en
cours d’utilisation.
23. Les enfants devraient être supervisés afin de vous assurer
qu’ils ne jouent pas avec l’appareil.
24. Le produit n’est pas conçu pour être utilisé par des personnes
(incluant des enfants) aux capacités physiques, sensorielles
ou mentales réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné suffisamment
de supervision ou d’instructions relativement à l’utilisation de
l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre 0˚C
(32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez
pas près d’une source de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur excessive
telle que la lumière du soleil ou au feu.
4. Assurez-vous que le moniteur et le
cordon de l’adaptateur sont toujours hors
de portée des enfants, àau moins 1 mètre (3
pieds) de l’enfant ou du berceau, pour éviter
tout risque de strangulation.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du
parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)
portative avec un article tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des
interférences sur votre moniteur vidéo et audio. Tentez
d’installer votre moniteur vidéo ou audio à l’écart des appareils
électroniques tels que des routeurs sans fil, radios, téléphones
cellulaires, interphones, moniteurs, téléphones, ordinateurs
personnels, électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une
firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans fil
portatifs et les stimulateurs cardiaques implantés dans l’organisme.
Appuyée par l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
• Vous devriez maintenir les dispositifs sans fil à au moins six
pouces du simulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement sur
le stimulateur cardiaque, tel que dans une poche de chemise,
lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens
qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se
rapportant aux champs électromagnétiques (EMF) standard. Si
vous le manipulez correctement en suivant les instructions de ce
guide, son utilisation sera sécuritaire pendant de nombreuses
années, selon les meilleures évidences scientifiques dont nous
disposons aujourd’hui.
To keep this product working well and looking good, follow these guidelines:
• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors
or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
General product care
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a
valid proof of purchase (“Consumer” or “you”) that the Product and
all accessories provided in the sales package (“Product”) are free
from defects in material and workmanship, pursuant to the following
terms and conditions, when installed and used normally and in
accordance with the Product operating instructions. This limited
warranty extends only to the Consumer for Products purchased and
used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in
materials and workmanship during the limited warranty period
(“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service
representative will replace at VTech’s option, without charge, a
Materially Defective Product. If we choose to replace the Product,
we may replace it with a new or refurbished Product of the same
or similar design. We will retain defective parts, modules, or
equipment. Replacement of the Product, at VTech’s option, is your
exclusive remedy. VTech will return the replacement Products to you
in working condition. You should expect the replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1)
YEAR from the date of purchase (90 days on products purchased as
Refurbished*). This limited warranty also applies to the replacement
Product for a period of either (a) 90 days from the date the
replacement Product is shipped to you or (b) the time remaining on
the original one-year warranty (90-day limited warranty on products
that are purchased as Refurbished*); whichever is longer.
*Refurbished products purchased from our online store carry a
90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or
other physical damage, improper installation, abnormal operation
or handling, neglect, inundation, fire, water or other liquid
intrusion; or
2. Product that has been damaged due to repair, alteration or
modification by anyone other than an authorized service
representative of VTech; or
3. Product to the extent that the problem experienced is caused by
signal conditions, network reliability, or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with
non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number
plates or electronic serial numbers have been removed, altered or
rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from
outside the United States of America or Canada, or used for
commercial or institutional purposes (including but not limited to
Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see item 2
below); or
8. Charges for installation or set up, adjustment of customer controls,
and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at
www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call
1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a
check of the Product’s controls and features may save you a service
call.
Except as provided by applicable law, you assume the risk of loss
or damage during transit and transportation and are responsible
for delivery or handling charges incurred in the transport of the
Product(s) to the service location. VTech will return replaced Product
under this limited warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for damage or loss of the
Product in transit.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the
Product to the VTech service location along with a description of
the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the
Product purchased (Product model) and the date of purchase or
receipt; and
3. Provide your name, complete and correct mailing address, and
telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you
and VTech. It supersedes all other written or oral communications
related to this Product. VTech provides no other warranties for
this Product. The warranty exclusively describes all of VTech’s
responsibilities regarding the Product. There are no other express
warranties. No one is authorized to make modifications to this limited
warranty and you should not rely on any such modification. State/
Provincial Law Rights: This warranty gives you specific legal rights,
and you may also have other rights, which vary from state to state or
province to province.
Limitations: Implied warranties, including those of fitness for a
particular purpose and merchantability (an unwritten warranty that
the Product is fit for ordinary use) are limited to one year from the
date of purchase. Some states/provinces do not allow limitations
on how long an implied warranty lasts, so the above limitation may
not apply to you. In no event shall VTech be liable for any indirect,
special, incidental, consequential, or similar damages (including, but
not limited to lost profits or revenue, inability to use the Product or
other associated equipment, the cost of substitute equipment, and
claims by third parties) resulting from the use of this Product. Some
states/provinces do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may
not apply to you.
Please retain your original sales receipt as proof of purchase.
Limited warranty
The RBRC seal
The RBRC seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating in an industry
program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the
United States and Canada. The program provides a convenient alternative to placing used Ni-MH batteries into the
trash or municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent product at local retailers participating in the program
or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery
recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set
up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery.
The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery
charging testing mode is activated while it is powered off and charging.
California Energy Commission battery charging testing mode
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user’s
manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise
through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
For the latest information and support, check out our website.
Use your smartphone or mobile device to access online
support by scanning the QR code on the right.
- OR -
Go to https://help.vtechphones.com/tm8112 or
https://help.vtechphones.com/tm8112-2
You can also call our Customer Support at 1 (800) 595-9511 [in US]
or 1 (800) 267-7377 [in Canada] for help.
S
m
TM8112
TM8112-2
Need help?
Turn on and off glow-on-the-ceiling night light
Directly on the baby unit:
• Press to turn the night light on, and press again to turn it off.
Remotely on the parent unit:
• Press to turn the night light on, the Night Light LED light will light up.
• Press again to turn the night light off, the Night Light LED light will switch off.
Parent unit alert tones
Low battery tone • Beeps twice every 10 minutes when the battery is low.
Out of range tone • Beeps three times every 30 seconds when there is no link
between the baby unit and parent unit, or when the parent unit is
out of range from the baby unit.
Frequency control Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 1921.536 - 1928.448 MHz
Parent unit: 1921.536 - 1928.448 MHz
Channels 5
Nominal effective
range
Maximum power allowed by FCC and IC. Actual operating range may vary
according to environmental conditions at the time of use.
Power
requirements
Baby unit adapter: Input: 100-120V AC 60Hz; Output: 6V DC @ 400mA
Parent unit adapter: Input: 100-120V AC 60Hz; Output: 6V DC @ 400mA
Parent unit battery: 2.4V 400mAh Ni-MH battery
Technical specifications
  • Page 1 1
  • Page 2 2

VTech TM8112 Manuel utilisateur

VTech
Marque
VTech
Modèle
TM8112
Catégorie
Babyphones
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes