PowerStroke PS262311 Le manuel du propriétaire
- Catégorie
- Nettoyeurs haute pression
- Taper
- Le manuel du propriétaire
SAVE THIS MANUAL FOR FUTURE REFERENCE
Ce nettoyeur haute pression a été conçu et fabriqué conformément
aux strictes normes de fiabilité, simplicité d’emploi et sécurité
d’utilisation. Correctement entretenu, il vous donnera des années
de fonctionnement robuste et sans problème.
AVERTISSEMENT :
Pour réduire les risques de
blessures, l’utilisateur doit lire et veiller à bien comprendre
le manuel d’utilisation avant d’utiliser ce produit.
Merci de votre achat.
Su lavadora de presión ha sido diseñada y fabricada
de conformidad con las estrictas normas para brindar
fiabilidad, facilidad de uso y seguridad para el operador. Con el
debido cuidado, le brindará muchos años de sólido y eficiente
funcionamiento.
ADVERTENCIA: Para reducir el riesgo de lesiones, el
usuario debe leer y comprender el manual del operador antes
de usar este producto.
Le agradecemos su compra.
CONSERVER CE MANUEL POUR
FUTURE RÉFÉRENCE GUARDE ESTE MANUAL PARA
FUTURAS CONSULTAS
Your pressure washer has been engineered and manufactured to our high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
OPERATOR’S MANUAL
Manuel d’utilisation
Manual del operador
2600 PSI PRESSURE WASHER
NETTOYEUR HAUTE PRESSION DE 2 600 PSI
LAVADORA A PRESIÓN DE 2 600 PSI
PS262311
TM
To register your
POWERSTROKE product, please visit:
http://register.powerstroketools.com/
Pour enregistrer votre produit de
POWERSTROKE, s’il vous plaît la visite:
http://register.powerstroketools.com/
Para registrar su producto de
POWERSTROKE, por favor visita:
http://register.powerstroketools.com/
CUSTOMER SERVICE
SERVICE CLIENTELE
SERVICIO AL CLIENTE
1-877-617-3501
www.powerstroketools.com
ii
See this fold-out section for all of the figures referenced
in the operator’s manual.
Consulter l’encart à volets afin d’examiner toutes les
figures mentionnées dans le manuel d’utilisation.
Consulte esta sección desplegable para ver todas las
figuras a las que se hace referencia en el manual del
operador.
iii
Fig. 1
A - Fuel cap (bouchon de carburant, tapa del
combustible)
B - Starter grip and rope (poignée du lanceur,
mango del arrancador retráctil)
C - Fuel tank (réservoir de carburant, tanque de
combustible)
D - Oil cap/dipstick (bouchon/jauge d’huile , tapa
del aceite con varilla de nivel)
E - Injection hose (d’injection transparent,
manguera de inyección)
F - Detergent container (réservoir de détergent,
recipiente del detergente)
G - Fuel valve - (robinet de carburant, válvula de
combustible)
H - On/stop switch (interrupteur marche et buteé,
interruptor de encendido y tope)
I - Choke (volet de départ, anegador)
J - High pressure hose (manguera de alta
presión)
K - Nozzle storage (buses et rangement de buse,
boquillas y compartimientos para boquillas)
L - Handle (poignée, mango)
M
- Trigger handle (poignée de gâchete, mango
del gatillo)
N- Trigger with lock out (gâchette avec
verouillage, gatillo con seguro)
O - Spray wand (lance de pulvérisation , tubo de
rociado)
P - Gripping surface (surface de prise, superficie
de sujeción)
E
Fig. 2
A - Push to insert (capuchon de verrouillage du
manche, tapa de aseguramiento del mango)
Fig. 3
C
P
D
L
A
B
M
N
0
F
J
I
H
G
A - Trigger handle (poignée à gâchette,
mango del gatillo)
B - Connector (connecteur, conector)
C - Spray wand (lance de pulvérisation,
tubo de rociado)
A
B
C
K
iv
A - Funnel (entonnoir, embudo)
B - Fuel cap (bouchon du réservoir bouchon du
réservoir, tapa del tanque de combustible)
Fig. 4
A - OPEN (ouvrir, abra)
B - CLOSE (pour fermer, para cerrar)
Fig. 5
A - Collar (collier, casquillo)
B - Inlet coupler (raccord d’entrée, acoplador de
entrada)
C - High pressure hose (tuyau haute pression,
manguera de alta presión)
Fig. 7
Fig. 6
A - Threaded nipple (têton fileté, conexión
roscada)
B - Collar (collier, casquillo)
Fig. 11
A - Starter grip and rope (poignée du lanceur,
mango del arrancador retráctil)
B - Choke (volet de départ, anegador)
A
B
C
B
A
A
C
B
B
Fig. 8
A - Oil cap/dipstick (bouchon / jauge d’huile, tapa
del aceite con varilla de nivel)
A
A
A - Water intake (rise d’eau, entrada de agua)
B - Screen (tamis, cedazo)
C - Garden hose (tuyau d’arrosage, manguera de
jardín)
A
FUEL VALVE
ROBINET DE CARBURANT
VÁLVULA DE COMBUSTIBLE
Fig. 9
OPEN
CLOSE
ON
A
BB
ON/STOP SWITCH
INTERRUPTEUR MARCHE / BUTEÉ
INTERRUPTOR DE ENCENDIDO/ TOPE
A - OFF (arrêt, apagado)
B - ON (marche, encendido)
A
B
Fig. 10
v
Fig. 13
A - Trigger (gâchette, gatillo)
B - Slot (fente, ranura)
C - Lock Out (bouton de verrouillage, seguro)
A - Detergent container (réservoir de détergent,
recipiente del detergente)
B - Injection hose (d’injection transparent,
manguera de inyección)
Fig. 12
A
25
Fig. 14
A - Nozzle (embout, boquilla)
B - “Click” (déclic, hasta que trabe)
C - Quick-connect collar (casquillo de conexión
rápida)
D - Spray wand (lance de pulvérisation, tubo de
rociador)
E - Pull back the quick-connect collar (tirer la
bague à connexion rapide, tire del collar de
conexión rápida)
F - Push the nozzle into place (insérer en place la
buse, introduzca la boquilla en su lugar)
G - Push the collar forward (poussez en avant la
bague, empuje del collar adelante)
Fig. 15
Fig. 16
Fig. 17
A
B
C
D
TO MOVE THE MACHINE
DÉPLACEMENT DE LA MACHINE
PARA MOVER LA MÁQUINA
TO STORE THE MACHINE
REMISAGE DE LA MACHINE
PARA GUARDAR LA MÁQUINA
25
NOZZLE PATTERNS:
40º - Gentle rinse
25º - General purpose or large surfaces
0º - Spot cleaning or high-to-reach areas
Black nozzle - Detergent application
DIFFÉRENTES CONFIGURATIONS :
40º - Rinçage délicat
25º - Général ou grandes surfaces
0º - nettoyage d’endroit ou pour les endroits
difficiles d’accès
Buse noir - application de détergente
PATRONES DE ROCIADO:
40º - Enjuague leve
25º - Propósito general o superficies grandes
0º - Limpiar de lugar o para las partes de
difícil acceso
Negra boquilla - aplicación de detergente
F
E
G
C
B
AB
40º
25º
0º
SOAP
Page 2 — English
Introduction ...................................................................................................................................................................... 2
Introduction / Introducción
General Safety Rules ........................................................................................................................................................ 3
Règles de sécurité générales / Reglas de seguridad generales
Specific Safety Rules ........................................................................................................................................................ 4
Règles de sécurité particulières / Reglas de seguridad específicas
Symbols .........................................................................................................................................................................5-6
Symboles / Símbolos
Features ............................................................................................................................................................................ 7
Caractéristiques / Características
Assembly .......................................................................................................................................................................7-8
Assemblage / Armado
Operation .....................................................................................................................................................................9-11
Utilisation / Funcionamiento
Maintenance ..............................................................................................................................................................11-12
Entretien / Mantenimiento
Troubleshooting .............................................................................................................................................................. 13
Dépannage / Solución de problemas
Warranty ......................................................................................................................................................................... 14
Garantie / Garantía
Parts Ordering and Service ...............................................................................................................................Back Page
Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la
conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à
utiliser et à entretenir.
* * *
Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
INTRODUCTION
INTRODUCTION / INTRODUCCIÓN
TABLE OF CONTENTS
TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO
Page 3 — English
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire and/or carbon monoxide poisoning which will cause
death or serious personal injury.
READ ALL INSTRUCTIONS
Know your tool. Read the operator’s manual carefully.
Learn the machine’s applications and limitations as well
as the specific potential hazards related to this tool.
Keep guards in place and in working order. Never oper-
ate the tool with any guard or cover removed. Make sure
all guards are operating properly before each use.
Remove adjusting keys and wrenches. Form habit of
checking to see that keys and adjusting wrenches are
removed from tool before turning it on.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept
a safe distance from work area.
Keep the area of operation clear of all persons,
particularly small children, and pets.
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
Carbon monoxide, a colorless, odorless, and extremely
dangerous gas, can cause unconsciousness or death.
Use right tool. Don’t force tool or attachment to do a
job it was not designed for. Don’t use it for a purpose not
intended.
Dress properly. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Exercise caution to avoid slipping or falling.
Always wear eye protection with side shields marked
to comply with ANSI Z87.1. Following this rule will re-
duce the risk of serious personal injury.
Don’t overreach or stand on unstable support. Keep
proper footing and balance at all times.
Use only recommended accessories. The use of
improper accessories may cause risk of injury.
Follow the maintenance instructions specified in this
manual.
Check damaged parts. Before further use of the
tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
Never leave tool running unattended. Turn power off.
Don’t leave tool until it comes to a complete stop.
Keep the engine free of grass, leaves, or grease to
reduce the chance of a fire hazard.
Keep the exhaust pipe free of foreign objects.
Follow manufacturer’s recommendations for safe
loading, unloading, transport, and storage of
machine.
Be thoroughly familiar with controls. Know how to stop
the product and bleed pressure quickly.
Keep tool dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use
brake fluids, gasoline, petroleum-based products, or any
solvents to clean tool.
Stay alert and exercise control. Watch what you are
doing and use common sense. Do not operate tool when
you are tired. Do not rush.
Do not operate the product while under the influence
of drugs, alcohol, or any medication.
Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or string
which can be thrown or become entangled in the
machine.
Do not use tool if switch does not turn it off. Have
defective switches replaced by an authorized service
center.
Before cleaning, repairing, or inspecting, shut off the
engine and make certain all moving parts have stopped.
Disconnect the spark plug wire, and keep the wire away
from the plug to prevent accidental starting.
Avoid dangerous environment. Don’t use in damp or
wet locations or expose to rain. Keep work area well
lit.
Never use in an explosive atmosphere. Normal
sparking of the motor could ignite fumes.
Do not operature while smoking or near an open
flame.
Do not operate around dry brush, twigs, cloth rags, or
other flammable materials.
WARNING: Risk of injection or injury – Do not direct
discharge stream at persons.
Page 4 — English
SPECIFIC SAFETY RULES
Never direct a water stream toward people or pets,
or any electrical device.
Before starting any cleaning operation, close doors
and windows. Clear the area to be cleaned of debris,
toys, outdoor furniture, or other objects that could create
a hazard.
Never pick up or carry a machine while the engine is
running.
Never start the machine if ice has formed in any part
of the equipment.
Do not use acids, alkalines, solvents, flammable
material, bleaches, or industrial grade solutions
in this product. These products can cause physical
injuries to the operator and irreversible damage to the
machine.
Always operate the machine on a level surface. If the
engine is on an incline, it could seize due to improper
lubrication (even at the maximum oil level).
WARNING: High pressure jets can be dangerous
if subject to misuse. The jet must not be directed at
persons, animals, electrical devices, or the machine
itself.
Never attempt to make any adjustments while the
engine (motor) is running (except where specifically
recommended by the manufacturer).
Protective covers must always cover rotating parts
when the engine is running.
Keep cooling air intake (starter grip and rope area) and
muffler side of the engine at least 3 feet away from build-
ings, obstructions, and other combustible objects.
Keep the engine away from flammables and other
hazardous materials.
Keep away from hot parts. The muffler and other engine
parts become very hot; use caution.
Do not touch the spark plug and ignition cable when
starting and operating the engine.
Check fuel hoses and joints for looseness and fuel
leakage before each use.
Check bolts and nuts for looseness before each use.
A loose bolt or nut may cause serious engine prob-
lems.
Always refuel outdoors. Never refuel indoors or in a
poorly ventilated area.
Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present,
such as hot water and space heaters, clothes dryers,
and the like.
If the fuel tank has to be drained, do this outdoors.
To reduce the risk of fire and burn injury, handle fuel
with care. It is highly flammable.
Do not smoke while handling fuel.
Add fuel before starting the engine. Never remove the
cap of the fuel tank or add fuel while the engine is running
or when the engine is hot.
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
Replace all fuel tank and container caps securely.
Wipe spilled fuel from the unit. Move 30 feet away from
refueling site before starting engine.
If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
Never attempt to burn off spilled fuel under any
circumstances.
Before storing, allow the engine to cool.
Store fuel in a cool, well-ventilated area, safely away
from spark and/or flame-producing equipment.
Store fuel in containers specifically designed for this
purpose.
Empty fuel tank and restrain the unit from moving
before transporting in a vehicle.
When servicing use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
ONLY use cold water.
Make sure minimum clearance of 3 feet is maintained
from combustible materials.
Never spray close to the surface to be cleaned as you
can damage the surface.
After stopping the engine, always pull the trigger on
the trigger handle to relieve stored pressure in the
high pressure hose. Failure to do so could result in seri-
ous personal injury.
Save these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone this
tool, loan them these instructions also.
Page 5 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe
operation of this product.
SYMBOL NAME EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Wet Conditions Alert Do not expose to rain or use in damp locations.
Hot Surface To reduce the risk of injury or damage, avoid contact with any
hot surface.
Risk of Injections
To reduce the risk of injection or injury, never direct a water
stream towards people or pets or place any body part in the
stream. Leaking hoses and fittings are also capable of causing
injection injury. Do not hold hoses or fittings.
Risk of Explosion Fuel and its vapors are explosive and can cause severe burns
or death.
Risk of Fire Fuel and its vapors are extremely flammable and explosive. Fire
can cause severe burns or death.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
Page 6 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe
operation of this product.
SYMBOL NAME EXPLANATION
Toxic Fumes
Gas products emit carbon monoxide, an odorless, colorless,
poison gas. Breathing carbon monoxide can cause nausea,
fainting, or death.
Kickback To reduce the risk of injury from kickback, hold the spray wand
securely with both hands when the machine is on.
Electric Shock Failure to use in dry conditions and to observe safe practices
can result in electric shock.
Chemical Burns
To reduce the risk of injury or damage, DO NOT USE ACIDS,
ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,
OR INDUSTRIAL GRADE SOLUTIONS in this product.
Page 7 — English
FEATURES
PRODUCT SPECIFICATIONS
Engine .............................................................................................................................................................Honda GCV160
Fuel Tank Capacity .................................................................................................................................... 0.29 gal (1.1 liters)
Maximum Pounds Per Square Inch Pressure* ......................................................................................................... 2,600 psi
Maximum Gallons Per Minute* ...................................................................................................................................2.3 gpm
Maximum Inlet Water Temperature ................................................................................................................................104˚F
*Max. rating determined by PWMA Standard 101
KNOW YOUR PRESSURE WASHER
See Figure 1, page iii.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
ON/STOP SWITCH
The on/stop switch is used in combination with the starter
grip and rope to start the engine. It is also used to turn the
engine off.
FUEL TANK
This fuel tank has a maximum capacity of 0.29 gal.
(1.1 liters). Use unleaded automotive gasoline in the
engine.
HONDA GCV160 ENGINE
This Honda engine enables the pressure washer to achieve
2,600 psi (pounds per square inch) at a rate of 2.3 gpm
(gallons per minute). Please read the engine manual included
with this product.
HOSE STORAGE
Once the high pressure hose is rolled, hang it on the back of
the machine using the stretch strap to secure in place.
STARTER GRIP AND ROPE
The starter grip and rope is pulled to start the machine.
SPARK ARRESTOR
This engine is not factory equipped with a spark arrestor.
In some areas it is illegal to operate an engine without a spark
arrestor. A spark arrestor is available by calling customer
service for assistance.
THERMAL RELIEF VALVE
This pump feature will prevent water temperatures from
reaching harmful levels by releasing a small amount of water
from a rubber hose. Once the water has drained, the thermal
relief valve will reset itself.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides added
control of the spray wand and helps reduce fatigue.
TRIGGER WITH LOCK OUT
Pulling the trigger releases a stream of water for high
pressure cleaning. The lock out provides protection against
unauthorized use.
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully cut the box down the sides then remove the
tool and any accessories from the box. Make sure that
all items listed in the packing list are included.
WARNING:
Do not use this product if any parts on the packing list
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-877-617-3501 for assistance.
Page 8 — English
ASSEMBLY
PACKING LIST
Pressure Washer
25 ft. High Pressure Hose
Trigger Handle
Spray Wand
Quick-connect Nozzles (4)
Injection Hose
Injection Hose Filter
4-Cycle Engine Oil (SAE 30 or SAE 10W30)
Handle
Operator’s Manual
WARNING:
If any parts are damaged or missing do not operate this
tool until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
INSTALLING THE HANDLE
See Figure 2, page iii.
To install the handle:
Push and hold the button on the handle as you slide the
handle into the holes in the frame.
NOTE: Before use, pull the handle up until the lock
button snaps through the locking slot to secure the
handle in place.
ASSEMBLING THE TRIGGER HANDLE
See Figure 3, page iii.
To attach the spray wand:
Place the threaded end of the spray wand in the connec-
tor on the end of the trigger handle.
Turn the connector clockwise until it stops. This secures
the spray wand in place.
CONNECTING HIGH PRESSURE HOSE TO
TRIGGER HANDLE
See Figure 4, page iv.
Screw the collar on the high pressure hose into the
trigger handle inlet coupler by turning the hose collar
clockwise.
Pull on the hose to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE TO
THE PUMP
See Figure 5, page iv.
After the high pressure hose has been uncoiled and attached
to the spray wand:
Align the collar on the threaded nipple on the pump.
Insert the the end of the high pressure hose collar into
the threaded nipple.
Turn the collar clockwise to tighten the hose securely to
the pump.
Pull on the hose to be certain it is properly secured.
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 6, page iv.
CAUTION:
Always observe all local regulations when connnecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water sup-
ply to prevent the feedback of chemicals into the drinking
water supply. Direct connection through a receiver tank
or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER
use hot water or water from pools, lakes, etc. Before
connecting the garden hose to the pressure washer:
Run water through the hose for 30 seconds to clean any
debris from the hose.
Inspect the screen in the water intake.
If the screen is damaged, do not use the machine until
the screen has been replaced.
If the screen is dirty, clean it before connecting the garden
hose to the machine.
Page 9 — English
OPERATION
WARNING:
Do not allow familiarity with tools to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this tool. The use of at-
tachments or accessories not recommended can result
in serious personal injury.
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to heed this warning could
result in serious injury.
APPLICATIONS
You may use this tool for the purposes listed below:
Removing dirt and mold from decks, cement patios, and
house siding
Cleaning boats, motorcycles, outdoor furniture, and
grills
ADDING/CHECKING ENGINE OIL
See Figure 7, page iv.
NOTE: This machine has been shipped with approximately
2 oz. of oil in the engine from testing. You must add oil to
the engine before starting it the first time.
CAUTION:
Any attempt to start the engine without adding oil will
result in engine failure.
To add engine oil:
Place pressure washer on a flat, level surface.
Unscrew the oil cap / dipstick by turning counter-
clockwise.
Before first use, squeeze the entire contents of the oil
container provided into the oil reservoir.
After initial use, add 4-stroke engine oil (SAE 30 or SAE
10W30) until the fluid level rises to the upper portion of
the hatched area on the dipstick. Do not overfill.
Replace the oil cap / dipstick and securely tighten.
NOTE: This engine has a total oil capacity of 20 oz.
(0.6 liters).
To check engine oil level:
Set engine on a flat surface.
Wipe dipstick clean and re-seat in hole; do not reth-
read.
Remove dipstick again and check oil level. Oil level should
fall within the hatched area on the dipstick.
If level is low, add engine oil until the fluid level rises to
the upper portion of the hatched area on the dipstick.
Replace and secure the oil cap/dipstick.
CAUTION:
Do not overfill. Overfilling the crankcase may cause ex-
cessive smoke and engine damage.
OXYGENATED FUELS
DO NOT USE E85 FUEL. IT WILL VOID YOUR WAR-
RANTY.
NOTE: Fuel system damage or performance problems re-
sulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated below are not
covered under warranty.
Ethanol. Gasoline containing up to 10% ethanol by volume
(commonly referred to as E10) or 15% ethanol by volume
(commonly referred to as E15) are acceptable. E85 is not.
ASSEMBLY
To connect the garden hose to the machine:
Uncoil the garden hose.
NOTE: There must be a minimum of 10 feet of unre-
stricted hose between the pressure washer intake and
the hose faucet or shut off valve (such as a “Y” shut off
connector).
With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
Page 10 — English
OPERATION
ADDING GASOLINE TO THE FUEL TANK
See Figure 8, page iv.
WARNING:
Gasoline and its vapors are highly flammable and
explosive. To prevent serious personal injury and prop-
erty damage, handle gasoline with care. Keep away from
ignition sources, handle outdoors only, do not smoke
while adding fuel, and wipe up spills immediately.
When adding gas to the pressure washer, make sure the unit
is sitting on a flat, level surface. If the engine is hot, let the
pressure washer cool before adding gas. ALWAYS fill the
fuel tank outdoors with the machine turned off.
NOTE: Use unleaded gas only. DO NOT mix oil with gas.
Before removing the fuel cap, clean the area around it.
Remove the fuel cap.
Insert a clean funnel into the fuel tank then slowly
pour gasoline into the tank. Fill tank to approximately
1-1/2 in. below the top of the tank neck (this allows for
fuel expansion).
Replace fuel cap and tighten until the cap “clicks”.
Clean up any spills before starting the engine.
WARNING:
Always shut off engine before fueling. Never add fuel to
a machine with a running or hot engine. Move at least
30 ft. from refueling site before starting engine. Do not
smoke and stay away from open flames and sparks!
Failure to follow these instructions could result in serious
personal injury.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figures 9 - 11, page iv.
CAUTION:
Do not run the pump without the water supply connected
and turned on.
Before starting the engine:
Connect all hoses.
Check all fluids (oil and gas).
Turn on the garden hose then squeeze the trigger to
relieve air pressure; hold the trigger until a steady stream
of water appears.
To start the engine:
Turn the fuel valve to the OPEN position.
Put the on/stop switch in the ON position.
Pull choke.
Grasp the starter grip and pull slowly until resistance is felt.
Give the starter grip a short, brisk pull to start the engine.
NOTE: Do not allow the starter grip and rope to snap
back after starting; return it gently to its original place.
Let engine run for several seconds, then push choke in.
To stop the engine:
Put the on/stop switch in the OFF position.
Turn the fuel valve to the CLOSED position.
NOTE: Shutting off the engine will not relieve pressure in the
system. Pull trigger to release water pressure.
WARNING:
Hold the handle securely with both hands. Expect the
trigger handle to move when the trigger is pulled due
to reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
USING THE SPRAY WAND TRIGGER
See Figure 12, page v.
For greater control and safety, keep both hands on the
trigger handle at all times.
Pull back and hold the trigger to operate the pressure
washer.
Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:
Push up on the lock out until it clicks into the slot.
To disengage the lock out:
Push the lock out down and into its original position.
For the most effective cleaning, the spray nozzle should be
between 8 in. and 24 in. from the surface to be cleaned. If
the spray is too close it can damage the cleaning surface.
SELECTING THE RIGHT NOZZLE FOR THE
JOB
See Figures 13 - 14, page v.
Before starting any cleaning job, determine the best nozzle
for the job. Each of the nozzles has a different spray
pattern. The nozzle patterns are: 40º (for gentle rinse),
25º (for general purpose or large surfaces), 0º (for spot
cleaning or high-to-reach areas), and the black nozzle for
using detergent.
WARNING:
NEVER change nozzles without locking the lock out on
the trigger handle and NEVER point the wand at your
face or at others. The quick-connect feature contains
small springs that could eject the nozzle with some force.
Failure to heed this may cause personal injury.
Page 11 — English
OPERATION
Using the quick-connect collar, changing nozzles is easy.
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
To connect a nozzle to the trigger handle:
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Pull back the quick-connect collar.
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
To disconnect a nozzle from the trigger handle once the
cleaning job is complete:
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place nozzle in the
nozzle storage area on the top of the machine.
WASHING WITH DETERGENT
See Figure 15, page v.
Use only detergents designed for pressure washers; house-
hold detergents, acids, alkalines, bleaches, solvents, flam-
mable material, or industrial grade solutions can damage
the pump. Many detergents may require mixing prior to use.
Prepare cleaning solution as instructed on the solution bottle.
Remove the cap from the detergent container and pour
detergent in the container. Replace cap on container.
Install the black nozzle on the spray wand.
Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
NOTE: To use a detergent bottle, open the detergent container
cap. Next, remove the filter from the end of the injection hose
then slide the hose out of the cap. Place the injection hose filter
back on the hose and place the hose in the bottom of the bottle.
For detergent application:
With the black nozzle installed on the spray wand and the
engine turned off, submerge the hose and black filter down
into the detergent container as far as it will go.
Before shutting off the engine:
Place the injection hose in a bucket of clean water.
Flush for 1 - 2 minutes (spray clear water through the
spray wand).
Shut off the engine.
NOTE: Shutting OFF ( O ) the engine will not relieve pressure
in the system. Pull trigger to release water pressure.
RINSING WITH THE PRESSURE WASHER
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place nozzle in the
nozzle storage area on the top of the machine.
Select the right nozzle for the job:
• Use medium pressure nozzle (green) for items such as
a car or boat.
• Use higher pressure nozzle for jobs such as stripping
paint and degreasing the driveway. When using these
nozzles, test a small area first to avoid surface damage.
NOTE: If injection hose is installed, remove before rinsing.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
MOVING THE PRESSURE WASHER
See Figure 16, page v.
NOTE: Never lift or carry this product using the handle.
Turn the pressure washer off.
Tilt the machine toward you until it balances on the wheels
then roll the machine to the desired position.
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Before inspecting, cleaning or servicing the machine, shut
off engine, wait for all moving parts to stop, and discon-
nect spark plug wire and move it away from spark plug.
Failure to follow these instructions can result in serious
personal injury or property damage.
Page 12 — English
MAINTENANCE
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at an authorized service center.
Before running the engine, perform the following pre-
operation steps:
Check that all bolts, nuts, etc., are securely tightened.
Make sure the air filter is clean.
Check both the engine oil level and the fuel tank level;
refill as needed.
Inspect the work area for hazards.
If there is excessive noise or vibration, stop the unit
immediately.
NOZZLE MAINTENANCE
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Remove the nozzle from the spray wand.
NOTE: Never point the spray wand at your face.
To free any foreign materials clogging or restricting the
nozzle, blow out or remove debris with a fine needle.
Using a garden hose, flush debris out of nozzle by back
flushing (running the water through the nozzle backwards
or from the outside to the inside).
Reconnect the nozzle to the spray wand.
Turn on the water supply and start the engine.
STORING THE PRESSURE WASHER
See Figure 17, page v.
Store the pressure washer with the gas tank empty by either
draining the tank or running the pressure washer until the
gas runs out. Allow 30 minutes of “cool down” time before
storing the machine. Store in a dry, covered area where the
weather can’t damage it.
It is important to store this product in a frost-free area. Always
empty water from all hoses, the pump, and the detergent
bucket before storing.
NOTE: Use of a fuel stabilizer and pump saver will give you
better performance and increase the life of the machine.
Discharge Fuel:
Drain the fuel tank completely. Stored gas can go stale in
30 days.
Engine Oil:
Drain the oil and replace with fresh, clean oil.
Spark Plug:
Disconnect spark plug wire and remove the spark plug.
Pour about a teaspoon of clean, air-cooled, four-cycle
oil through the spark plug hole into the combustion
chamber.
Leaving the spark plug out, pull the starter cord two or
three times to coat the inside of the cylinder wall.
Inspect the spark plug and clean or replace, as neces-
sary.
Reinstall the spark plug, but leave the spark plug wire
disconnected.
Air Filter:
Clean the air filter.
Hoses and Pump:
Flush the injection hose with clean water for 1-2 minutes.
Remove all hoses. Empty the pump by pulling on the starter
grip and rope about 6 times. This should remove most of
the liquid from the pump.
WARNING:
Ensure all engine cover and all engine parts are com-
pletely and properly reassembled before starting engine.
Failure to correctly reassemble engine may result in seri-
ous injury or property damage.
PREPARING FOR USE AFTER STORAGE
Pull the starter grip and rope grip three or four times to
clean oil from the combustion chamber.
Remove spark plug from the cylinder. Wipe oil from the
spark plug and return it to the cylinder.
Reconnect the spark plug wire.
Refuel the machine as described earlier in the operator’s
manual.
Page 13 — English
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Engine fails to start 1. No fuel in tank 1. Fill tank
2. Spark plug shorted or fouled 2. Replace spark plug
3. Spark plug is broken (cracked 3. Replace spark plug
porcelain or electrodes broken)
4. Ignition lead wire shorted, broken, 4. Replace lead wire or attach to spark
or disconnected from spark plug plug
5. Ignition inoperative 5. Contact authorized service center
Engine hard to start 1. Water in gasoline 1. Drain entire system and refill with
fresh fuel
2. Weak spark at spark plug 2. Contact authorized service center
Engine lacks power 1. Dirty air filter 1. Clean or replace air filter
Detergent fails to mix with spray 1. Detergent injection hose is not 1. Insert injection hose into detergent
properly submerged container or detergent bottle
2. High pressure nozzle attached 2. Use low pressure nozzle (black) to
apply detergent
Pump doesn’t produce pressure 1. Low pressure nozzle installed 1. Replace with high pressure nozzle
2. Inadequate water supply 2. Provide adequate water flow
3. Trigger handle or spray wand leaks 3. Check connections and / or replace
trigger handle or spray wand
4. Nozzle is clogged 4. Clean nozzle
5. Pump is faulty 5. Contact authorized service center
6. Air in line 6. Squeeze trigger on trigger handle to
remove air from line
Machine doesn’t reach high 1. Diameter of garden hose is too 1. Replace with 3/4 in. garden hose
pressure small
2. Water supply is restricted 2. Check garden hose for kinks, leaks,
and blockages
3. Not enough inlet water 3. Open water source full force
4. Wrong nozzle is attached 4. Attach the high pressure nozzle
Page 14 — English
WARRANTY
LIMITED WARRANTY
WARRANTY COVERAGE
OWT Industries, Inc., (the Company) warrants to the original retail purchaser that this PowerStroke Product is free from
defects in material and workmanship and agrees to repair or replace, at the Company’s sole discretion, any defective
Product free of charge within these time periods from the date of purchase:
Two years, if the Product is used solely for personal, family, or household use;
90 days, if the Product is used for business or commercial use.
This warranty applies only to Products sold within the United States of America, the District of Columbia, Canada,
Mexico, the Commonwealth of Puerto Rico, the Virgin Islands, Guam, the Canal Zone, or American Samoa.
This warranty is not transferable and does not cover damage resulting from defects other than in material or workman-
ship, or damage caused by unreasonable use, including the failure to provide reasonable and necessary maintenance.
Other items not covered under this warranty include:
Transportation charges for sending the product to the Company or its authorized service representative for warranty
service, or for shipping repaired or replacement products back to the customer; these charges must be borne by
the original retail purchaser.
Engine. Your Product is equipped with an engine that is covered exclusively by a separate warranty from the engine
manufacturer. Please refer to the engine manual included with the Product for warranty information related to the
engine.
Damages caused by abuse, accident, misuse, neglect, alteration, modification, the effects of corrosion, erosion,
normal wear and tear or repairs by other than the Company or its authorized service representative.
Warranty is voided if the customer fails to install, maintain and operate the product in accordance with the instruc-
tions and recommendations of the Company as set forth in the Product’s operator’s manual or if the Product is used
as rental equipment.
The Company will not pay for repairs or adjustments to the Product, or for any costs or labor, performed without the
Company’s prior authorization.
SAVE YOUR SALES SLIP
Proof of purchase in the form of your dated sales receipt, cash register slip, etc. showing the serial number and the
model of your Product will be required before the Company and/or its authorized service representatives can perform
warranty service on the Product.
EXCLUSIONS AND LIMITATIONS
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY IMPLIED WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, APPLICABLE TO THIS PRODUCT,
SHALL BE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. THE WARRANTY SERVICE
DESCRIBED ABOVE IS THE EXCLUSIVE REMEDY UNDER THIS WARRANTY. THE COMPANY SHALL NOT BE LIABILE
FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
SOME STATES DO NOT ALLOW A LIMITATION ON THE DURATION OF IMPLIED WARRANTIES, OR THE EXCLUSION
OR LIMITATION OF INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.
HOW TO OBTAIN WARRANTY SERVICE
For warranty service: Call toll free 1-877-617-3501, or write to OWT Industries, Inc., P.O. Box 35, Hwy. 8, Pickens,
SC 29671.
For warranty service outside the USA, please contact your local PowerStroke dealer.
NOTES
Page 3 — Français
INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ
AVERTISSEMENT :
Lire attentivement toutes les instructions. Le non-respect
de toutes les instructions ci-dessous peut entraîner un
choc électrique, un incendie et/ou une intoxication par le
monoxyde de carbone, ce qui peut causer des blessures
graves voire la mort.
LIRE TOUTES LES INSTRUCTIONS
Apprendre à connaître l’outil. Lire attentivement le manuel
d’utilisation. Apprendre les applications et les limites de l’outil,
ainsi que les risques spécifiques relatifs à son utilisation.
Maintenir tous les dispositifs de protection en place et en
bon état de fonctionnement. Ne jamais utiliser l’outil avec des
couvercles ou dispositifs de protection retirés. S’assurer que
tous les dispositifs de protection fonctionnent correctement
avant chaque utilisation.
Retirer les clés et outils de réglage. Prendre l’habitude
de vérifier que tous les outils et clés de réglage en ont été
retirés de l’outil avant de le mettre en marche.
Pour réduire les risques de blessures, garder les enfants
et visiteurs à l’écart. Tous les visiteurs doivent porter des
lunettes de sécurité et se tenir à bonne distance de la zone
de travail.
,
particulièrement les petits enfants et les animaux
domestiques.
Ne pas faire tourner le moteur dans un espace confiné
où des vapeurs toxiques de monoxyde de carbone peuvent
s’accumuler. Le monoxyde de carbone, un gaz incolore,
inodore et extrêmement toxique peut causer une perte de
conscience et être mortel.
Utiliser l’outil approprié. Ne pas utiliser l’outil ou un
accessoire pour effectuer un travail pour lequel il n’est pas
conçu. Ne ne pas utiliser l’outil pour une application non
prévue.
Porter une tenue appropriée. Ne pas porter de vêtements
amples, gants, cravate ou bijoux. Ces articles pourraient
être happés et tirer la main ou une partie du corps dans les
pièces en mouvement. Des gants en caoutchouc et des
chaussures antidérapantes sont recommandées pour le
travail à l’extérieur. Les cheveux longs doivent être ramassés
sous un couvre-chef.
similaires. Porter des chaussures de sécurité protégeant les
pieds et améliorant l’équilibre sur des surfaces glissantes.
Faire preuve de prudence pour éviter de glisser ou
tomber.
Toujours porter une protection oculaire avec écrans
latéraux certifiée conforme à la norme ANSI Z87.1. Le
respect de cette règle réduira les risques de blessures
graves.
instable. Toujours se tenir bien campé et en équilibre.
N’utiliser que les accessoires recommandés. L’emploi de
tout accessoire inadapté peut présenter un risque de blessure.
Suivre les instructions d’entretien spécifiées dans ce
manuel.
Avant d’utiliser l’outil de nouveau
examiner soigneusement les pièces et dispositifs de
protection qui semblent endommagés afin de déterminer
s’ils fonctionnent correctement et s’ils remplissent les
fonctions prévues. Vérifier l’alignement des pièces mobiles,
s’assurer qu’aucune pièce n’est bloquée ou cassée,
vérifier la fixation de chaque pièce et s’assurer qu’aucun
autre problème ne risque d’affecter le bon fonctionnement
de l’outil. Pour éviter les risques de blessures, toute
protection ou pièce endommagée doit être correctement
réparée ou remplacée dans un centre de réparations agréé.
Ne jamais laisser un outil en fonctionnement sans
surveillance. Ne pas s’éloigner de l’outil avant qu’il soit
parvenu à un arrêt complet.
pour réduire le risque d’incendie.
débris.
Veiller à savoir arrêter la machine et relâcher la pression
rapidement.
Toujours utiliser un chiffon propre pour le nettoyage. Ne
jamais utiliser de liquide de freins, d’essence ou de produits
à base de pétrole pour nettoyer l’outil.
Rester vigilant et garder le contrôle. Se montrer attentif
et faire preuve de bon sens. Ne pas utiliser l’outil en état de
fatigue. Ne pas se presser.
drogues ou de médicaments.
La
débarrasser de tous les objets tels que cailloux, verre brisé,
clous, fils métalliques, cordes, etc. risquant d’être projetés
ou de se prendre dans la machine.
Ne pas utiliser l’outil si le commutateur ne permet pas
de l’arrêter. Faire remplacer les commutateurs défectueux
dans un centre de réparations agréé.
couper le moteur
et vérifier que toutes les pièces en mouvement sont arrêtées.
Déconnecter le fil de bougie et garder le fil à l’écart de la
bougie afin d’empêcher un démarrage accidentel.
Éviter les environnements dangereux. Ne pas utiliser dans
des endroits mouillés ou humides, ne pas exposer à la pluie.
Garder le lieu de travail bien éclairé.
Les
étincelles normalement produites par le moteur pourraient
enflammer les vapeurs.
Ne jamais utiliser en fumant ou à côté d’une flamme vive.
Ne pas utiliser à proximité de buissons secs, brindilles,
chiffons ou autres matériaux inflammables.
Le non-respect de
cet avertissement pourrait entraîner des blessures graves.
AVERTISSEMENT : Risque d’injection ou de blessures
– ne pas diriger le jet directement vers quelqu’un.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
PowerStroke PS262311 Le manuel du propriétaire
- Catégorie
- Nettoyeurs haute pression
- Taper
- Le manuel du propriétaire