PowerStroke PS8C310E Le manuel du propriétaire

PowerStroke
Marque
PowerStroke
Modèle
PS8C310E
Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire
OPERATOR’S MANUAL
MANUEL D’UTILISATION
3100 PSI PRESSURE WASHER
LAVEUSE À PRESSION DE 3 100 PSI
PS8C310E
CUSTOMER SERVICE
SERVICE CLIENTELE
English: 1-877-617-3501
French: 1-800-268-4015
www.powerstroketools.com
To register your POWERSTROKE product, please visit:
http://register.powerstroketools.com/
Pour enregistrer votre produit de POWERSTROKE, s’il vous
plaît la visite: http://register.powerstroketools.com/
NOTICE AVIS
Do not use E15 or E85 fuel in this product. It is
a violation of federal law and will damage the
unit and void your warranty. Only use unleaded
gasoline containing up to 10% ethanol.
Ne pas utiliser d’essence E15 ou E85 dans ce produit. Une
telle utilisation représente une violation de la loi fédérale et
endommagera l’appareil et annulera la garantie. Utiliser seulement
de l’essence sans plomb ne contenant pas plus de 10 % d’éthanol.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
WARNING: To reduce the risk of injury, the user must
read and understand the operator’s manual before using this
product.
AVERTISSEMENT : Pour réduire les risques de
blessures, l’utilisateur doit lire et veiller à bien comprendre le
manuel d’utilisation avant d’utiliser ce produit.
TABLE OF CONTENTS
Important Safety Instructions .................................................. 2
Specific Safety Rules .............................................................. 3
Symbols ...............................................................................4-5
Features ..................................................................................6
Assembly .............................................................................6-9
Operation ...........................................................................9-13
Maintenance ....................................................................14-17
Troubleshooting ....................................................................18
Warranty ................................................................................ 19
Parts Ordering / Service ...........................................Back Page
TABLE DES MATIÈRES
Instructions importantes concernant la sécurité .....................2
Règles de sécurité particulières ...............................................3
Symboles .............................................................................. 4-5
Caractéristiques .......................................................................6
Assemblage .......................................................................... 6-9
Utilisation ............................................................................ 9-14
Entretien ...........................................................................15-16
Dépannage .............................................................................17
Garantie ..................................................................................18
Commande de pièces et réparation ....................... Page arrière
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
ii
Fig. 1
A - Fuel cap / bouchon de carburant
B - Starter grip and rope / poignée du lanceur et
corde
C - Fuel tank / réservoir de carburant
D - Oil cap/dipstick / bouchon/jauge d’huile
E - Gripping surface / surface de prise
F - Engine switch / commutateur du moteur
G - Fuel valve / robinet de carburant
H - Battery maintainer charger / chargeur/
mainteneur de batterie
I - Choke / étrangleur
J - High pressure hose / tuyau haute pression
K - Nozzle storage / rangement de buse
L - Handle / poignée
M
- Trigger handle / poignée de gâchette
N - Trigger with lock out / gâchette avec verrouillage
O - Spray wand / lance de pulvérisation
P - Muffler / silencieux
Q - Battery / batterie
R - Maintainer input / entrée du chargeur/
mainteneur
S - Soap tank / réservoir de savon
Fig. 2 Fig. 3 Fig. 4
A - Push to insert / pousser pour insérer
A - Trigger handle / poignée à gâchette
B - Connector / connecteur
C - Spray wand / lance de pulvérisation
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner toutes les figures
mentionnées dans le manuel d’utilisation.
A
A
A
E
JM
N
O
Q
H
B
L
F
S
G
R
I
D
P
C
K
A
B
C
A - Red female wire (+) / câble femelle rouge (+)
B - Positive (+) terminal / borne positive (+)
C - Red male wire (+) / câble mâle rouge (+)
D - Black female wire (–) / câble femelle noir (–)
E - Negative (–) terminal / borne négative (–)
F - Black male wire (–) / câble mâle noir (–)
G - Cap / capuchon
B
GC
D
AEF
iii
Fig. 5
A - Threaded outlet / raccord fileté
B - Collar / collier
A - Battery / batterie
B - Battery bracket / support de batterie
C - Tab / languette
Fig. 8
A - Water intake / prise d’eau
B - Screen / tamis
C - Garden hose / tuyau d’arrosage
Fig. 9
Fig. 6 Fig. 7
A - Oil cap/dipstick / bouchon/jauge d’huile
Fig. 10
A - Fuel cap / bouchon du réservoir
B - Funnel / entonnoir
A
C
B
BA
A
D
B
A
B
A - Inlet coupler / raccord d’entrée
B - Collar / collier
C - High pressure hose / tuyau haute pression
B
C
D - Opening / ouverture
E - Battery holder / porte-batterie
F - Bolt / boulon
F
AC
E
A
iv
Fig. 15
A - Starter grip and rope / poignée du lanceur et
corde
Fig. 18
Fig. 19
A - Nozzle / embout
B - “Click” / déclic
C - Quick-connect collar / collier à ressort
D - Spray wand / lance de pulvérisation
E - Pull back the quick-connect collar / tirer la
bague à connexion rapide
F - Push the nozzle into place / insérer en place la
buse
G - Push the collar forward / poussez la bague
A
B
C
D
F
E
G
A
Fig. 17
Fig. 14
A - Trigger / gâchette
B - Slot / fente
C - Lock out / bouton de verrouillage
A
B
C
Fig. 16
A - OFF position / position ARRÊT
B - Engine switch / interrupteur du moteur
A - ON position / position MARCHE
B - Lock button / bouton de verrouillage
C - Engine switch / interrupteur du moteur
D - START position / position DÉMARRAGE
1
2
1
2
A
A
B
C
D
B
Fig. 12
Fig. 11
A - Engine switch / interrupteur du moteur
B - Choke / étrangleur
C - Fuel valve / robinet de carburant
OFF
ENGINE
SWITCH
ON
START
C
B
A
A - OPEN position / position OUVERT
B - CLOSED position / position FERMÉ
C - Fuel valve / robinet de carburant
C
B
A
Fig. 13
A - Choke / étrangleur
B - RUN position / position FERMÉ
C - START position / position DÉMARRAGE
A
B
C
v
Fig. 20
TO MOVE THE MACHINE
DÉPLACEMENT DE LA MACHINE
Fig. 22
A - Fuse holder / porte-fusible
B - Fuse / fusible
A - Maintainer input / entrée du chargeur/
mainteneur
B - Battery maintainer charger / chargeur/
mainteneur de batterie
C - Cover / couvercle
Fig. 27
Fig. 24
Fig. 25
Fig. 23
TO STORE THE MACHINE
REMISAGE DE LA MACHINE
A - Straightened paper clip / trombone droit
B - Nozzle / buse
B
A
B
B
C
A
A
C
B
A
Fig. 21
A - Threaded top / bouchon vissé
B - Rubber seal / joint de caoutchouc
C - Paper seal / sceaux de papier
D - Water intake / rise d’eau
E - Pump outlet / sortie de la pompe
F - Pump protector / protecteur de pompe
E
D
A
F
A - Flange nuts (écrous de bride)
B - Muffler cover (couvercle de silencieux)
C - Spark arrestor (pare-étincelles)
D - Screw (vis)
E - Wire brush (brosse métallique)
Fig. 26
A
B
CD
E
Page 2 — English
DANGER:
Risk of fire and serious burns: Never remove fuel cap
when unit is running. Shut off engine and allow the unit
to cool at least five minutes. Remove cap slowly.
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire and/or carbon monoxide poisoning which will cause
death or serious personal injury.
READ ALL INSTRUCTIONS
Know your tool. Read the operator’s manual carefully.
Learn the machine’s applications and limitations as well
as the specific potential hazards related to this tool.
Keep guards in place and in working order. Never
operate the tool with any guard or cover removed. Make
sure all guards are operating properly before each use.
Remove adjusting keys and wrenches. Form habit of
checking to see that keys and adjusting wrenches are
removed from tool before turning it on.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept
a safe distance from work area.
Keep the area of operation clear of all persons,
particularly small children, and pets.
Do not start or operate the engine in a confined space,
building, near open windows, or in other unventilated
space where dangerous carbon monoxide fumes can
collect. Carbon monoxide, a colourless, odourless, and
extremely dangerous gas, can cause unconsciousness
or death.
Use right tool. Don’t force tool or attachment to do a
job it was not designed for. Don’t use it for a purpose not
intended.
Dress properly. Wear long pants and long sleeves. Do
not wear loose clothing, gloves, neckties, or jewelry. They
can get caught and draw you into moving parts. Rubber
gloves and nonskid footwear are recommended when
working outdoors. Also wear protective hair covering to
contain long hair.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Exercise caution to avoid slipping or falling.
Always wear eye protection with side shields marked
to comply with ANSI Z87.1. Following this rule will
reduce the risk of serious personal injury.
Don’t overreach or stand on a ladder, rooftop, or other
unstable support. Keep proper footing and balance at
all times.
Use only recommended accessories. The use of
improper accessories may cause risk of injury.
Follow the maintenance instructions specified in this
manual.
Check damaged parts. Before further use of the tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged must
be properly repaired or replaced by a qualified service
centre to avoid risk of personal injury.
Never leave tool running unattended. Turn power off.
Don’t leave tool until it comes to a complete stop.
Keep the engine free of grass, leaves, or grease to
reduce the chance of a fire hazard.
Keep the exhaust pipe free of foreign objects.
Follow manufacturer’s recommendations for
safeloading, unloading, transport, and storage of
machine.
Be thoroughly familiar with controls. Know how to stop
the product and bleed pressure quickly.
Keep tool dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use
brake fluids, gasoline, petroleum-based products, or any
solvents to clean tool.
Stay alert and exercise control. Watch what you are
doing and use common sense. Do not operate tool when
you are tired. Do not rush.
Do not operate the product while under the influence
of drugs, alcohol, or any medication.
Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or
string which can be thrown or become entangled in the
machine.
Do not use tool if switch does not turn it off. Have
switch replaced by a qualified service centre.
Before cleaning, repairing, or inspecting, shut off the
engine and make certain all moving parts have stopped.
Disconnect the spark plug wire, and keep the wire away
from the plug to prevent accidental starting.
Avoid dangerous environment. Don’t use in damp or
wet locations or expose to rain. Keep work area well
lit.
Never use in an explosive atmosphere. Normal
sparking of the motor could ignite fumes.
Do not operate while smoking or near an open flame.
Do not operate around dry brush, twigs, cloth rags, or
other flammable materials.
WARNING: Risk of injection or injury – Do not direct
discharge stream at persons.
IMPORTANT SAFETY INSTRUCTIONS
Page 3 — English
Use caution when positioning the pressure washer
for use. Warm air from the engine could cause
discoloured spots on grass.
Never direct a water stream toward people or pets,
or any electrical device.
Before starting any cleaning operation, close doors
and windows. Clear the area to be cleaned of debris,
toys, outdoor furniture, or other objects that could create
a hazard.
Never pick up or carry a machine while the engine is
running.
Never start the machine if ice has formed in any part
of the equipment.
Do not use acids, alkalines, solvents, flammable
material, bleaches, or industrial grade solutions in
this product. These products can cause physical injuries
to the operator and irreversible damage to the machine.
Always operate the machine on a level surface. If the
engine is on an incline, it could seize due to improper
lubrication (even at the maximum lubricant level).
WARNING: High pressure jets can be dangerous
if subject to misuse. The jet must not be directed at
persons, animals, electrical devices, or the machine
itself.
Hold the trigger handle securely with both hands. Ex-
pect the trigger handle to move when the trigger is pulled
due to reaction forces. Failure to do so could cause loss
of control and injury to yourself and others.
Never attempt to make any adjustments while the
engine (motor) is running (except where specifically
recommended by the manufacturer).
Protective covers must always cover rotating parts
when the engine is running.
Keep cooling air intake (starter grip and rope area) and
muffler side of the engine at least 914 mm (3 feet) away from
buildings, obstructions, and other combustible objects.
Keep the engine away from flammables and other
hazardous materials.
Keep away from hot parts. The muffler, exhaust gasses,
and other engine parts become very hot. Do not touch the
muffler or place any body parts in the path of hot exhaust
gases, which can cause burns and other serious personal
injuries.
Do not touch the spark plug and ignition cable when
starting and operating the engine.
Check fuel hoses and joints for looseness and fuel
leakage before each use.
Check bolts and nuts for looseness before each use.
A loose bolt or nut may cause serious engine problems.
Always refuel outdoors. Never refuel indoors or in a poorly
ventilated area.
Never store the machine with fuel in the fuel tank inside
a building where ignition sources are present, such as hot
water and space heaters, clothes dryers, and the like.
If the fuel tank has to be drained, do this outdoors into
a container approved for gasoline and away from all
ignition sources.
To reduce the risk of fire and burn injury, handle fuel
with care. It is highly flammable.
Do not smoke while handling fuel.
Add fuel before starting the engine. Never remove the
cap of the fuel tank or add fuel while the engine is running
or when the engine is hot.
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
Replace all fuel tank and container caps securely.
Wipe spilled fuel from the unit. Move 30 feet away from
refueling site before starting engine.
If fuel is spilled, do not attempt to start the engine, but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapours have
dissipated.
Never attempt to burn off spilled fuel under any
circumstances.
Before storing, allow the pressure washer to cool for
30 minutes and drain fuel from the unit.
Store fuel in a cool, well-ventilated area, safely away
from spark and/or flame-producing equipment.
Store fuel in containers specifically designed for this
purpose.
Empty fuel tank and restrain the unit from moving before
transporting in a vehicle.
When servicing use only recommended or equivalent
replacement parts. Use of any other parts may create a
hazard or cause product damage.
ONLY use cold water.
Make sure minimum clearance of 914 mm (3 feet) is
maintained from combustible materials.
Never spray close to the surface to be cleaned as you
can damage the surface.
After stopping the engine, always pull the trigger on
the trigger handle to relieve stored pressure in the high
pressure hose. Failure to do so could result in serious
personal injury.
For outdoor use only.
Ensure the high pressure hose is properly connected
before using the product.
CAUTION: Risk of Injury. Disconnect Battery Ground
[Negative (–)] Terminal Before Servicing.
Keep battery away from other metal objects like paper
clips, coins, keys, nails, screws, or other small metal
objects that can make a connection from one terminal
to another. Shorting the battery terminals together may
cause burns or a fire.
Save these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone this
tool, loan them these instructions also.
SPECIFIC SAFETY RULES
Page 4 — English
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe
operation of this product.
SYMBOL NAME EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Wet Conditions Alert Do not expose to rain or use in damp locations.
Hot Surface and Exhaust Gases
To reduce the risk of injury or damage, avoid contact with any
hot surface and do not place any body parts in the path of hot
exhaust gases.
Risk of Injections
To reduce the risk of injection or injury, never direct a water
stream towards people or pets or place any body part in the
stream. Leaking hoses and fittings are also capable of causing
injection injury. Do not hold hoses or fittings.
Risk of Explosion Do not spray flammable liquids. Flammable liquids, fuel, and
their vapours are explosive and can cause severe burns or death.
Risk of Fire Fuel and its vapours are extremely flammable and explosive.
Fire can cause severe burns or death.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
NOTICE: (Without Safety Alert Symbol) Indicates important information not related to an
injury hazard, such as a situation that may result in property damage.
SYMBOLS
Page 5 — English
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe
operation of this product.
SYMBOL NAME EXPLANATION
Toxic Fumes
Gas products emit carbon monoxide, an odourless, colourless,
poison gas. Breathing carbon monoxide can cause nausea,
fainting, or death.
Kickback To reduce the risk of injury from kickback, hold the spray wand
securely with both hands when the machine is on.
Electric Shock Failure to use in dry conditions and to observe safe practices
can result in electric shock.
Chemical Burns
To reduce the risk of injury or damage, DO NOT USE ACIDS,
ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,
OR INDUSTRIAL GRADE SOLUTIONS in this product.
Recycle Symbol
This product uses lead acid (Pb) batteries. Local, state or federal
laws may prohibit disposal of batteries in ordinary trash. Consult
your local waste authority for information regarding available
recycling and/or disposal options.
SYMBOLS
Page 6 — English
PRODUCT SPECIFICATIONS
Fuel Tank Capacity ................................................................................................................................... 1.17 liter (0.31 gal.)
Maximum Pounds Per Square Inch Pressure* .........................................................................................................3,100 psi
Maximum Gallons Per Minute* ................................................................................................................ 9.09 LPM (2.4 gpm)
Maximum Inlet Water Temperature ......................................................................................................................40˚C (104˚F)
*Max. rating determined by PWMA Standard 101
KNOW YOUR PRESSURE WASHER
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
189cc OHC ENGINE
This engine enables the pressure washer to achieve 3,100 psi
(pounds per square inch) at a rate of 9.09 LPM [2.4 gpm
(gallons per minute)].
AUTOMATIC SOAP INJECTION SYSTEM
Pour pressure washer detergent into the soap tank to apply
detergent quickly and easily to your cleaning project. Use
of the soap nozzle will activate the soap injector at a 20:1
dilution ratio.
BATTERY MAINTAINER CHARGER
When storing the pressure washer, connect the battery
maintainer charger to keep the battery fully charged and
ready for use. If the battery’s charge is depleted, the Electric
Start feature will not function.
NOTE: The pressure washer engine does not charge or
maintain the battery as it runs.
ENGINE SWITCH
The engine switch is used either alone or in combination
with the starter grip and rope to start the pressure washer.
FUEL TANK
This fuel tank has a maximum capacity of 1.17 liter (0.31 gal.).
Use unleaded automotive gasoline in the engine.
HOSE STORAGE
Once the high pressure hose is rolled, hang it on the back
of the machine using the stretch strap to secure in place.
SOAP NOZZLE
The blue soap nozzle is used to apply detergent at low
pressure only.
STARTER GRIP AND ROPE
The starter grip and rope is pulled to start the machine.
THERMAL RELIEF VALVE
This pump feature will prevent water temperatures from
reaching harmful levels by releasing a small amount of
water. Once the water has drained, the thermal relief valve
will reset itself.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides
added control of the spray wand and helps reduce fatigue.
TRIGGER WITH LOCK OUT
Pulling the trigger releases a stream of water for high
pressure cleaning. The lock out provides protection against
unauthorized use.
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
FEATURES
ASSEMBLY
Page 7 — English
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-877-617-3501 for assistance.
PACKING LIST
Pressure Washer
Handle
7.6 m (25 ft.) High Pressure Hose
Trigger Handle
Spray Wand
Quick-Connect Nozzles (4)
4-Cycle Engine Lubricant (SAE 30 or SAE 10W30)
Disposable Funnel
Battery Maintainer Charger
Operator’s Manual
WARNING:
If any parts are damaged or missing do not operate this
tool until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
INSTALLING THE HANDLE
See Figure 2.
CAUTION:
Be careful to avoid pinching your fingers or hands when
installing the handle onto the frame.
Push and hold the button on the handle as you slide the
handle into the holes in the frame.
NOTE: Before use, pull the handle up until the lock button
snaps through the locking slot to secure the handle in
place.
CONNECTING THE SPRAY WAND TO THE
TRIGGER HANDLE
See Figure 3.
Place the threaded end of the spray wand in the connector
on the end of the trigger handle.
Turn the connector clockwise until it stops. This secures
the spray wand in place.
CONNECTING/DISCONNECTING BATTERY
See Figures 4 - 5.
WARNING:
To reduce the risk of electric shock or explosion, do not
short circuit the battery terminals or charge in a sealed
container. Keep sparks and flame away. Do not use
metal tools for connections and keep metal objects away
from the battery terminals. Metal objects can make a
connection from one terminal to another. Shorting the
battery terminals together can cause sparks, burns, or
a fire.
The battery terminal design does not require the use of tools
when installing or removing battery wires. All battery wires
must be connected before the electric start feature of the
pressure washer can be operated.
To connect the battery:
Remove the cap from the positive (+) terminal.
Connect the red female wire to the red male wire on the
positive (+) terminal.
NOTE: The black male, black female, and red male wires
have been preinstalled.
To replace the battery:
Drain lubricant and fuel from the pressure washer into
containers approved for lubricant and gasoline.
Disconnect the black wires from the battery’s negative
(–) terminal, first the female then the male wire.
Disconnect the red wires from the battery’s positive (+)
terminal, first the female then the male wire.
Carefully lay the pressure washer down so that it rests
on its handle.
NOTE: Do not attempt to access the battery by tilting
the unit as this may allow the pressure washer to fall
unexpectedly.
Using a 10 mm wrench, remove the retaining bolt securing
the battery holder to the battery bracket. Lift and slide
the battery holder to the left until it disengages from the
bracket.
Remove the old battery and dispose of according to local
and state regulations. Always abide by the safety warnings
provided with the battery.
ASSEMBLY
Page 8 — English
Put the battery holder on top of the new battery, then place
the new battery on the bracket in the same orientation as
the old one.
Insert the battery holder’s tab into the opening on the
battery bracket. Gently press down on the battery holder
while pushing it to the right to lock it into position.
Install the retaining bolt and return the pressure washer
to its upright position.
Connect the red wires to the battery’s positive (+) terminal,
first the male then the female wire.
Connect the black wires to the battery’s negative (–)
terminal, first the male then the female wire.
NOTE: Be careful not to short across the terminals when
installing. Shorting the terminals together can cause sparks,
damage to the battery or pressure washer, or even burns
or explosions.
CONNECTING HIGH PRESSURE HOSE TO
TRIGGER HANDLE
See Figure 6.
Screw the collar on the high pressure hose into the trigger
handle inlet coupler by turning the hose collar clockwise.
Tighten securely.
NOTE: Be careful to avoid cross-threading, which can
cause the trigger handle to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE TO
THE PUMP
See Figure 7.
Completely uncoil and straighten the high pressure hose
to prevent kinks.
NOTE: See Using the High Pressure Hose in Operation
for more information about using the high pressure hose.
Align the collar on the hose to the threaded outlet on the
pump.
Insert the high pressure hose collar onto the threaded
outlet.
Turn the collar clockwise to tighten the hose securely to
the pump.
NOTE: Be careful to avoid cross-threading, which can
cause the hose to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 8.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water
supply to prevent the feedback of chemicals into the
drinking water supply. Direct connection through a
receiver tank or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose to the pressure washer:
Run water through the hose for 30 seconds to clean any
debris from the hose.
Inspect the screen in the water intake.
If the screen is damaged, do not use the machine until
the screen has been replaced.
If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 3 m (10 feet) of
unrestricted hose between the pressure washer intake
and the hose faucet or shut off valve (such as a “Y” shut
off connector).
With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
ASSEMBLY
Page 9 — English
DO NOT OVERTILT THE UNIT!
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool. The use
of attachments or accessories not recommended can
result in serious personal injury.
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to follow these instructions
could result in serious injury, electric shock, or death.
WARNING:
Risk of serious burns. Do not touch the muffler or
place any body parts in the path of hot exhaust gases,
which can cause burns and other serious personal
injuries.
NOTICE:
The spark arrestor on this product has not been evaluated
by the USDA Forest Service and cannot be used on
U.S. forest lands. In addition, product users must
comply with Federal, State, and local fire prevention
regulations. Check with appropriate authorities. Refer
to accompanying engine manual for maintenance and
replacement parts.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts,
caps, etc. Tighten securely all fasteners and caps and
do not operate this product until all missing or damaged
parts are replaced. Please contact customer service or
a qualified service centre for assistance.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills,
playground equipment, etc.
*Always test in an inconspicuous area first.
ASSEMBLY
OPERATION
Page 10 — English
ADDING/CHECKING ENGINE LUBRICANT
See Figure 9.
NOTE: This machine has been shipped with approximately
0.06 l (2 oz.) of lubricant in the engine from testing. You must
add lubricant to the engine before starting it the first time.
NOTICE:
Any attempt to start the engine without adding lubricant
will result in engine failure.
To add engine lubricant:
Place pressure washer on a flat, level surface. Do not tilt.
Unscrew the oil cap/dipstick by turning counter-
clockwise.
Before first use, squeeze the entire contents of the
lubricant container provided into the oil reservoir.
After initial use, add 4-stroke engine lubricant (SAE 30 or
SAE 10W30) until the fluid level rises to the upper portion
of the hatched area on the dipstick. Do not overfill.
Replace the oil cap/dipstick and securely tighten.
To check engine lubricant level:
Place pressure washer on a flat, level surface. Do not tilt.
Unscrew the oil cap/dipstick by turning counter-
clockwise.
Wipe dipstick clean and re-seat in hole; do not rethread.
Remove dipstick again and check lubricant level. Lubricant
level should fall within the hatched area on the dipstick.
If level is low, add engine lubricant until the fluid level rises
to the upper portion of the hatched area on the dipstick.
Replace and secure the oil cap/dipstick.
NOTICE:
Do not overfill. Overfilling the crankcase may cause
excessive smoke and engine damage.
ETHANOL-BLENDED FUELS
NOTICE:
Do not use E15 or E85 fuel in this product. It is a
violation of federal law and will damage the unit
and void your warranty. Only use unleaded gasoline
containing up to 10% ethanol.
ADDING GASOLINE TO THE FUEL TANK
See Figure 10.
DANGER:
Risk of fire and serious burns: Never remove fuel cap
when unit is running. Shut off engine and allow the unit
to cool at least five minutes. Remove cap slowly.
WARNING:
Gasoline and its vapours are highly flammable and
explosive. To prevent serious personal injury and property
damage, handle gasoline with care. Keep away from
ignition sources, handle outdoors only, do not smoke
while adding fuel, and wipe up spills immediately.
WARNING:
Always shut off engine before fueling. Never remove fuel
cap or add fuel to a machine with a running or hot engine.
Make sure the unit is sitting on a flat, level surface and
only add fuel outdoors. If the engine is hot, let the unit
cool for at least five minutes before adding fuel. After fu-
eling, immediately replace fuel cap and tighten securely.
Move at least 9 m (30 ft.) from refueling site before starting
engine. Do not smoke and stay away from open flames
and sparks! Failure to follow these instructions could
result in a fire and cause serious personal injury.
WARNING:
Check for fuel leaks. A leaking fuel cap, tank, or line is a
fire hazard and must be replaced immediately. If you find
any leaks, correct the problem before using the product.
Failure to do so could result in a fire that could cause
serious personal injury.
NOTE: This is a 4-cycle engine. DO NOT mix fuel and
lubricant together.
Mix fuel stabilizer with gasoline according to fuel stabilizer
manufacturer’s directions.
Before removing the fuel cap, clean the area around it.
Remove the fuel cap.
Insert a clean funnel into the fuel tank then slowly pour
gasoline into the tank. Fill tank to approximately 38 mm
(1-1/2 in.) below the top of the tank neck (this allows for
fuel expansion).
Replace fuel cap and tighten until the cap “clicks”.
Clean up any spills before starting the engine.
ELECTRIC START
This pressure washer model is provided with both electric
start and recoil start capabilities. Avoid prolonged cranking,
as it can damage the engine.
The battery provided is a nominal 12 volt sealed rechargeable
lead-acid battery and can be operated in any position without
leakage. It complies with non-spillable battery regulations.
NOTE: Brand new pressure washers are shipped with the
red female wire (+) disconnected. The cap must be removed
and the red female wire (+) must be connected to the positive
OPERATION
Page 11 — English
(+) terminal on the battery before the Electric Start feature
will work.
For initial battery connection, see Connecting/Disconnecting
Battery.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figures 11 - 16.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Before starting the engine:
Connect the battery.
Connect all hoses.
NOTE: Make sure the pressure washer’s water intake
screen is in place and unclogged before connecting
garden hose.
Check all fluids (oil and gas).
Turn on the garden hose then squeeze the trigger to
relieve air pressure; hold the trigger until a steady stream
of water appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the engine:
Turn the fuel valve to the OPEN position.
Pull the choke out to the START position.
NOTE: If engine is warm or the temperature is above 10˚C
(50˚F), push the choke in to the RUN position.
Push in at the top of the engine switch to put it in the ON
position.
Slide down and hold the lock button while pushing the
engine switch to the START position.
NOTE: The battery may require charging before the
pressure washer can be started using only the engine
switch.
The pressure washer can also be started by pulling the
starter grip and rope until the engine runs.
NOTE: Do not allow the starter grip and rope to snap
back after starting; return it gently to its original place.
NOTICE:
If the starter grip and rope becomes difficult to pull,
squeeze the trigger to relieve water pressure before at-
tempting to start the engine again.
Allow the engine to run for 5 seconds, then push the
choke in to the RUN position.
NOTICE:
Routinely make a visual inspection of the pump and
engine during use. If you notice any lubricant leaking
around the pump or engine seals, stop using the pres-
sure washer immediately. Contact customer service or
a qualified service centre for repair. Failure to do so may
cause property damage.
To stop the engine:
Put the engine switch in the OFF position by pushing in
at the bottom of the switch.
NOTE: Shutting off the engine will not relieve pressure in the
system. Pull trigger to release water pressure.
WARNING:
While operating and storing, keep at least 3 feet of
clearance on all sides of this product, including overhead.
Allow a minimum of 30 minutes of “cool down” time
before storage. Keep all body parts, clothing, combustible
materials, and hoses away from the muffler. Heat created
by muffler and exhaust gases could be hot enough to
cause serious burns, ignite combustible objects, and/
or damage high pressure hoses that can result in an
injection injury.
USING THE TRIGGER HANDLE
See Figure 17.
WARNING:
Hold the trigger handle securely with both hands. Expect
the trigger handle to move when the trigger is pulled due
to reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
Pull back and hold the trigger to operate the pressure
washer.
Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:
Push up on the lock out until it clicks into the slot.
To disengage the lock out:
Push the lock out down and into its original position.
Start with the nozzle 30-60 cm (1-2 ft.) away from the cleaning
surface. and carefully approach the surface just until the
desired level of cleaning is achieved. If the spray is too close
it can damage the cleaning surface.
OPERATION
Page 12 — English
SELECTING THE RIGHT NOZZLE FOR THE JOB
See Figure 18.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. Refer to the Nozzle Selection Guide for more information
about which nozzle to choose.
WARNING:
NEVER remove nozzles without first turning off the
engine, relieving the water pressure in the trigger
handle, and locking the lock out on the trigger handle.
NEVER point the nozzle at your face or at others. The
quick-connect feature contains small springs that could
eject the nozzle with some force. Failure to follow these
instructions could result in an eye injury or other serious
personal injury.
To connect a nozzle to the spray wand:
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Pull back the quick-connect collar.
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
To disconnect a nozzle from the spray wand once the
cleaning job is complete:
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Pull back and hold the quick-connect collar.
Remove the nozzle by pulling it from the quick-connect
collar. Place nozzle in the nozzle storage area on the top
of the machine.
USING THE HIGH PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high
pressure hose prior to and during each use and do
not allow it to become kinked. The high pressure hose
features an outer covering that provides strength to the
hose. If the outer covering becomes damaged, stop using
the hose and replace it immediately. A kinked or damaged
hose can develop a high pressure leak and result in a
possible injection or other serious personal injury.
ABRASIVE GENTLE
NOZZLE SELECTION GUIDE
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
LOW
PRESSURE
(FOR SOAP OR
GENTLE RINSE)
0º Red 25º Green 40º White Blue Soap Nozzle
Concrete, Brick, Masonry   
Siding, Gutters, House  
Fencing, Deck, Patio  
Lawn Equipment, Boat, RV 
Recommended Nozzle Use With Caution for Certain Applications
OPERATION
Page 13 — English
To prevent damage to the outer covering:
Inspect the hose before every use.
Fully unwrap and straighten hose before use.
Do not allow the high pressure hose to be kinked.
Keep hose away from hot surfaces and sharp edges.
Do not pull unit by high pressure hose.
Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 19 - 20.
As sold, this unit is designed for use with “downstream” pres-
sure washer detergents. To convert for use with “upstream”
detergents, contact an customer service or a qualified service
centre for more information.
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS. Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump
or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
Remove the cap from the soap tank and pour pressure
washer detergent in the tank. Replace cap on tank.
NOTE: The machine setting of this unit is 20:1, which
usually allows the use of 3.79 l (1 gallon) pressure washer
detergent without further dilution. Check your detergent
instructions to be sure additional dilution is not necessary.
Install the blue soap nozzle on the spray wand.
Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
Before shutting off the engine:
Fill the soap tank with clean water.
Spray the clear water through the spray wand until the
tank is empty.
If any detergent remains in the spray, repeat with a second
tank of clean water.
Shut off the engine.
NOTE: Shutting off the engine will not relieve pressure in the
system. Pull trigger to release water pressure.
RINSING WITH THE PRESSURE WASHER
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Remove the soap nozzle and place in the nozzle storage
area.
Select the right nozzle for the job. See the chart shown
earlier in the manual to select the appropriate nozzle.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
USING PUMP PROTECTOR
See Figure 21.
Regular use of a commercially available pump protector
prolongs the life of the pressure washer by removing hard
water mineral deposits, lubricating pump seals and pistons,
and preventing freeze damage. Pump protector should be
added to the unit after every use and before storage. Pump
protector can be purchased at the retailer where you purchased
your pressure washer, or by calling customer service.
The instructions that follow are typical for adding pump
protector but you should always verify the specific instructions
provided by the manufacturer of the pump protector used.
Turn off the pressure washer engine and shut off the water
supply. Pull trigger to release water pressure.
Disconnect garden hose and high pressure hose.
Unscrew threaded top from pump protector bottle and
remove paper seal from bottle. Reinstall top on bottle and
tighten securely.
NOTE: The rubber seal should remain inside the threaded
top. If it comes out, be sure to replace before reinstalling
the top.
Remove bottle cap and attach threaded end of bottle
securely to pressure washer pump water intake.
Squeeze bottle to inject contents into pump.
With engine switch off, pull starter grip and rope to cycle
pump, then squeeze bottle again to guarantee complete
coverage.
Pump is protected when the protector fluid exits the pump
outlet.
MOVING THE PRESSURE WASHER
See Figure 22.
NOTE: Never lift or carry this product using the handle and
never place the unit in any position other than upright on
its wheels.
Turn the pressure washer off.
Tilt the machine toward you slightly until it balances on
the wheels then roll the machine to the desired position.
Do not tilt forward or sideways when moving.
DO NOT attempt to move the unit by pulling on any of
the hoses.
OPERATION
Page 14 — English
Normal maintenance, replacement or repair of emission con-
trol devices and systems may be performed by any qualified
repair establishment or individual with original or equivalent
parts. Warranty and recall repairs must be performed by an
authorized service centre; please contact customer service
for assistance.
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug. Failure to follow these instructions can result in
serious personal injury or property damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
When servicing, use only recommended or equivalent
replacement parts. Use of any other parts could create
a hazard or cause product damage.
CAUTION:
Risk of Injury. Disconnect Battery Ground [Negative (–)]
Terminal Before Servicing.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are
replaced. Please contact customer service or a qualified
service centre for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which could result in serious personal injury.
Before running the engine, perform the following pre-
operation steps:
Check that all bolts, nuts, etc., are securely tightened.
Make sure the air filter is clean.
Check both the engine lubricant level and the fuel tank
level; refill as needed.
Inspect the work area for hazards.
If there is excessive noise or vibration, stop the unit
immediately.
NOZZLE MAINTENANCE
See Figure 23.
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Remove the nozzle from the spray wand.
WARNING:
NEVER remove nozzles without first turning off the engine,
relieving the water pressure in the trigger handle, and
locking the lock out on the trigger handle. NEVER point
the nozzle at your face or at others. The quick-connect
feature contains small springs that could eject the nozzle
with some force. Failure to follow these instructions could
result in an eye injury or other serious personal injury.
To free any foreign materials clogging or restricting the
nozzle, blow out or remove debris with a straightened
paper clip or fine needle.
Using a garden hose, flush debris out of nozzle by back
flushing (running the water through the nozzle backwards
or from the outside to the inside).
Reconnect the nozzle to the spray wand.
Turn on the water supply and start the engine.
PUMP LUBRICATION
The pump on this product was lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
PUMP MAINTENANCE
Routinely make a visual inspection of the pump. If you notice
any leaking of lubricant around the pump seals, take the
pressure washer to an authorized service centre for repair.
There are no user serviceable parts to the pressure washer
pump. Any attempt to service or alter the pump may damage
the pressure washer and void your product warranty.
MAINTENANCE
Page 15 — English
USING THE BATTERY MAINTAINER CHARGER
See Figure 24.
When storing the pressure washer, connect the battery
maintainer charger to keep the battery fully charged and
ready for use.
NOTE: The battery maintainer charger provided should only
be used with the 12V 4.5Ah/20HR sealed lead acid battery
model RT1245B supplied with this pressure washer.
Plug the battery maintainer charger into a standard
household 120V receptacle. Make sure the household
power supply is 120V, 60 Hz, AC only.
Remove the input cover and connect the battery maintainer
charger to the pressure washer’s maintainer input. The
light on the battery maintainer charger will illuminate red
while the battery is charging.
The battery will become slightly warm to the touch while
charging. This is normal and does not indicate a problem.
When battery is fully charged, the red light will turn green.
NOTE: If the light does not illuminate, the battery maintainer
fuse may need to be replaced. Check the fuse and replace
if needed.
Disconnect the battery maintainer charger before operating
the pressure washer. Place the cover over the the pressure
washer’s maintainer input when not in use.
CHANGING BATTERY MAINTAINER CHARGER
FUSE
See Figure 25.
NOTICE:
Do not use a higher rated fuse other than the specified
amperage. This could cause damage to the product.
Open the fuse holder and remove the old fuse.
Insert new 7.5 amp fuse and close the fuse holder.
SPARK ARRESTOR
See Figure 26.
WARNING:
Muffler surfaces are very hot during and after operation
of the pressure washer. To avoid serious personal injury,
keep all body parts away from the muffler.
NOTICE:
The spark arrestor on this product has not been evalu-
ated by the USDA Forest Service and cannot be used
on U.S. forest lands. In addition, product users must
comply with Federal, State, and local fire prevention
regulations. Check with appropriate authorities. Refer
to accompanying engine manual for maintenance and
replacement parts.
Inspect the spark arrestor for breaks or holes. Clean or
replace if necessary.
To clean the spark arrestor:
Allow the muffler to cool completely.
Remove the flange nuts securing the muffler cover. Remove
cover and set aside.
Remove the screw securing the spark arrestor in place.
Remove the spark arrestor and gently clean using a wire
brush (not provided).
Replace the spark arrestor and reinstall the screw. Tighten
to secure.
Replace the muffler cover. Reinstall flange nuts and tighten
securely.
STORING THE PRESSURE WASHER
See Figure 27.
NOTE: Regular use of fuel stabilizer and pump protector
will give you better performance of the unit and increase
the life of the pump.
WARNING:
While storing, keep at least 914 mm (3 feet) of clearance
on all sides of this product, including overhead. Allow
a minimum of 30 minutes of “cool down” time before
storage. Heat created by muffler and exhaust gases could
be hot enough to ignite combustible objects.
Store in a dry, covered area where the weather can’t damage it.
It is important to store this product in a frost-free area. Always
empty water from all hoses, the pump, and the soap tank
before storing.
Drain the fuel tank completely by running the pressure
washer until the gas runs out. Stored gas can go stale in
30 days.
NOTE: Make sure the water supply is connected and
turned on when allowing the pressure washer engine to
run.
Make sure the engine switch is in the OFF position and
the fuel valve is in the CLOSED position.
Disconnect both the high pressure hose and the garden
hose from the pump.
Empty the pump by pulling on the starter grip and rope
about 6 times. This should remove most of the liquid from
the pump.
NOTICE:
The use of a pump protector is required after each use
and before storing to prevent cold weather and seal
damage during storage. Failure to use pump protector
will void your warranty.
Drain the lubricant and replace with fresh, clean lubricant
as described in Adding/Checking Engine Lubricant in
the Operation section of this manual.
MAINTENANCE
Page 16 — English
Disconnect spark plug wire and remove the spark plug.
Pour about a teaspoon of clean, air-cooled, four-cycle
lubricant through the spark plug hole into the combustion
chamber.
Leaving the spark plug out, pull the starter grip and rope
two or three times to coat the inside of the cylinder wall.
Inspect the spark plug and clean or replace, as necessary.
Reinstall the spark plug, but leave the spark plug wire
disconnected.
Clean the air filter.
Extend the starter grip and rope rope to check its condition.
If the rope is frayed, have it replaced immediately by a
qualified service centre.
Remove all hoses. Coil the hoses and store as shown.
Do not allow the hose to become kinked.
For short-term storage, connect the charging cable
and allow the battery to charge. For long-term storage,
disconnect the cable and coil it neatly.
Store the unit and accessories in an area that does not
reach freezing temperatures. Do not store near furnace or
other sources of heat that could dry out the pump seals.
PREPARING FOR USE AFTER STORAGE
Pull the starter grip and rope grip three or four times to
clean lubricant from the combustion chamber.
Remove spark plug from the cylinder. Wipe lubricant from
the spark plug and return it to the cylinder.
Reconnect the spark plug wire.
Refuel the machine as described earlier in the operator’s
manual.
BATTERY REMOVAL AND PREPARATION
FOR RECYCLING
WARNING:
To reduce the risk of electric shock or explosion, do
not short circuit the battery terminals. Keep sparks and
flame away. Do not use metal tools for connections and
keep metal objects away from the battery terminals.
Metal objects can make a connection from one terminal
to another. Shorting the battery terminals together can
cause sparks, burns, or a fire.
To preserve natural resources, please recycle
or dispose of batteries properly.
This product uses lead acid batteries. Local,
state or federal laws may prohibit disposal of
batteries in ordinary trash.
Consult your local waste authority for information regarding
available recycling and/or disposal options.
WARNING:
Upon removal, cover the battery’s terminals with
heavy-duty adhesive tape. Do not attempt to destroy or
disassemble battery or remove any of its components.
Lead acid batteries must be recycled or disposed of
properly. Also, never touch both terminals with metal
objects and/or body parts as short circuit may result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
MAINTENANCE
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

PowerStroke PS8C310E Le manuel du propriétaire

PowerStroke
Marque
PowerStroke
Modèle
PS8C310E
Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents