Ryobi RY802900VNM Le manuel du propriétaire

Ryobi
Marque
Ryobi
Modèle
RY802900VNM
Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire

Ce manuel convient également à

OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
2900 PSI PRESSURE WASHER
LAVEUSE À PRESSION DE 2 900 PSI
LAVADORA A PRESIÓN DE 2 900 PSI
RY802900/RY802900VNM/
RY802900AND
NOTICE AVIS AVISO
Do not use E15 or E85 fuel in this
product. It is a violation of federal
law and will damage the unit and
void your warranty. Only use unleaded gasoline containing
up to 10% ethanol.
Ne pas utiliser d’essence E15 ou E85 dans ce produit. Une
telle utilisation représente une violation de la loi fédérale
et endommagera l’appareil et annulera la garantie. Utiliser
seulement de l’essence sans plomb ne contenant pas plus
de 10 % d’éthanol.
No utilice combustibles E15 o E85 con este producto. Esto
constituye una violación a la ley federal, dañará la unidad
y anulará la garantía. Use únicamente gasolina sin plomo
con un contenido de hasta 10 % de etanol.
WARNING: To reduce the risk of
injury, the user must read and understand
the operator’s manual before using this
product.
TABLE OF CONTENTS
Important Safety Instructions ...............2
Specific Safety Rules ...........................3
Symbols ............................................4-5
Features ............................................5-6
Assembly ..........................................6-7
Operation ........................................8-12
Maintenance .................................13-15
Troubleshooting ............................16-17
Parts Ordering/Service ......... Back Page
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
TABLE DES MATIÈRES
Instructions importantes
concernant la sécurité .........................2
Règles de sécurité particulières ........... 3
Symboles ..........................................4-5
Caractéristiques ................................... 6
Assemblage ......................................7-8
Utilisation ........................................9-13
Entretien ........................................14-16
Dépannage ....................................17-18
Commande de pièces /
réparation ............................Páge arrière
ADVERTENCIA: Para reducir el
riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
ÍNDICE DE CONTENIDO
Instrucciones de seguridad
importantes .......................................... 2
Reglas de seguridad específicas ......... 3
Símbolos ...........................................4-5
Características .....................................6
Armado .............................................7-8
Funcionamiento ..............................9-13
Mantenimiento ..............................14-16
Solución de problemas .................17-18
Pedidos de piezas /
servicio ............................ Pág. posterior
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
ii
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner toutes les
figures mentionnées dans le manuel d’utilisation.
Consulte esta sección desplegable para ver todas
las figuras a las que se hace referencia en el manual
del operador.
A - Fuel cap (bouchon de carburant, tapa del
combustible)
B - Starter grip and rope (poignée du lanceur et
corde, mango del arrancador y cuerda)
C - Fuel tank (réservoir de carburant, tanque de
combustible)
D - Oil cap/dipstick (bouchon / jauge d’huile, tapa
del aceite con varilla de nivel)
E - Muffler (silencieux, silenciador)
F - Fuel valve (robinet de carburant, válvula de
combustible)
G - Stop switch (commutateur d’arrêt, interruptor
del apagado)
H - Choke (volet de départ, anegador)
I - High pressure hose (tuyau haute pression,
manguera de alta presión)
J - Spray wand (lance de pulvérisation, tubo de
rociado)
K - Handle (poignée, mango)
L
- Trigger handle (poignée de gâchete, mango
del gatillo)
M- Trigger with lock out (gâchette avec
verouillage, gatillo con seguro)
N - Soap injection hose with filter (tuyau pour
l’injection du savon avec filtre, manguera de
inyección del jabón con filtro)
O - 5-in-1 Change-over nozzle (buse à
permutation 5 en 1, boquilla intercambiable
5 en 1)
C
D
K
O
B
H
L
I
M
J
N
G
F
A
E
Fig. 1
iii
Fig. 2
A - Push to insert (pousser pour insérer, presione
para insertar)
Fig. 3
Fig. 4
A - Trigger handle (poignée à gâchette, mango
del gatillo)
B - Connector (connecteur, conector)
C - Spray wand (lance de pulvérisation, tubo de
rociado)
A - Collar (collier, casquillo)
B - Inlet coupler (raccord d’entrée, acoplador de
entrada)
C - High pressure hose (tuyau haute pression,
manguera de alta presión)
A
A
A
A
A
B
C
A - Fuel cap (bouchon du réservoir, tapa del
tanque de combustible)
A - OPEN (ouvrir, abra)
B - CLOSE (fermer, para cerrar)
Fig. 5
Fig. 7
Fig. 6
A - Threaded outlet (raccord fileté, salida con
rosca)
B - Collar (collier, casquillo)
B
A
C
A
B
Fig. 8
A - Oil cap/dipstick (bouchon / jauge d’huile, tapa
del aceite con varilla de nivel)
A
A
A - Water intake (rise d’eau, entrada de agua)
B - Screen (tamis, cedazo)
C - Garden hose (tuyau d’arrosage, manguera de
jardín)
FUEL VALVE
ROBINET DE CARBURANT
VÁLVULA DE COMBUSTIBLE
Fig. 9
OPEN
CLOSE
A
B
B
C
iv
Fig. 11
A - Starter grip and rope (poignée du lanceur et
corde, mango del arrancador y cuerda)
B - Choke (volet de départ, anegador)
A - Trigger (gâchette, gatillo)
B - Slot (fente, ranura)
C - Lock out (bouton de verrouillage, seguro)
Fig. 12
A
Fig. 16
C
B
Fig. 15
A
STOP SWITCH
COMMUTATEUR D’ARRÊT
INTERRUPTOR DEL APAGADO
A - OFF (arrêt, apagado)
A
Fig. 10
A - Soap injection hose with filter (tuyau pour
l’injection du savon avec filtre, manguera de
inyección del jabón con filtro)
B - Soap container (réservoir de savon,
recipiente del jabón)
C - Barbed fitting (raccord cannelé, conector
anillado)
B
A
A
C
Fig. 13
A - 5-in-1 Change-over nozzle (buse à
permutation 5 en 1, boquilla intercambiable
5 en 1)
B - Spray selector (sélecteur de jets , selector de
rociado )
Fig. 14
A - 5-in-1 Change-over nozzle (buse à
permutation 5 en 1, boquilla intercambiable
5 en 1)
B - Quick-connect collar (collier à ressort,
casquillo de conexión rápida)
C - Spray wand (lance de pulvérisation, tubo
rociador)
A
“CLICK”
DÉCLIC
CLIC
B
C
A
B
Fig. 17
A - Long range detergent [ ] (détergent à longue portée [ ], detergente de gran alcance [ ])
B - Short range detergent [ ] (détergent à courte portée [ ], detergente corto alcance [ ])
B
A
B
v
Fig. 19
Fig. 24
TO MOVE THE MACHINE
DÉPLACEMENT DE LA MACHINE
PARA MOVER LA MÁQUINA
TO STORE THE MACHINE
REMISAGE DE LA MACHINE
PARA GUARDAR LA MÁQUINA
Fig. 18
A - Threaded top (bouchon vissé, parte superior
roscada)
B - Rubber seal (joint de caoutchouc, sello de
goma)
C - Paper seal (sceaux de papier, sello de papel)
D - Water intake (rise d’eau, entrada de agua)
E - Pump outlet (sortie de la pompe, orificio de
descarga de la bomba)
F - Pump protector (protecteur de pompe,
protector de bomba)
C
B
A
A
E
F
D
Fig. 23
Fig. 21
Fig. 22
B
A
A
B
A - Air filter (filtre à air, filtro de aire)
B - Air filter cover (couvercle de filtre à air, tapa
del filtro de aire)
A - Spark plug (bougie, bujía)
B - Spark plug cap (creux de la bougie, tapa de
la bujía)
Fig. 20
A - Paper clip (pièces de papier, clips de papel)
B - 5-in-1 Change-over nozzle (buse à
permutation 5 en 1, boquilla intercambiable
5 en 1)
A
B
Page 2 — English
DANGER:
Risk of fire and serious burns: Never remove fuel cap when
unit is running. Shut off engine and allow the unit to cool at
least five minutes. Remove cap slowly.
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock, fire
and/or carbon monoxide poisoning which will cause death
or serious personal injury.
READ ALL INSTRUCTIONS
Know your tool. Read the operator’s manual carefully.
Learn the machine’s applications and limitations as well as
the specific potential hazards related to this tool.
Keep guards in place and in working order. Never operate
the tool with any guard or cover removed. Make sure all
guards are operating properly before each use.
Remove adjusting keys and wrenches. Form habit of
checking to see that keys and adjusting wrenches are re-
moved from tool before turning it on.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept a
safe distance from work area.
Keep the area of operation clear of all persons, particularly
small children, and pets.
Do not start or operate the engine in a confined space,
building, near open windows, or in other unventilated
space where dangerous carbon monoxide fumes can col-
lect. Carbon monoxide, a colorless, odorless, and extremely
dangerous gas, can cause unconsciousness or death.
Use right tool. Don’t force tool or attachment to do a job it
was not designed for. Don’t use it for a purpose not intended.
Dress properly. Wear long pants and long sleeves. Do not
wear loose clothing, neckties, or jewelry. They can get caught
and draw you into moving parts. Rubber gloves and nonskid
footwear are recommended when working outdoors. Also
wear protective hair covering to contain long hair.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Exercise caution to avoid slipping or falling.
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Following this rule will reduce the
risk of serious personal injury.
Don’t overreach or stand on a ladder, rooftop, or other
unstable support. Keep proper footing and balance at all
times.
Use only recommended accessories. The use of improper
accessories may cause risk of injury.
Follow the maintenance instructions specified in this
manual.
Check damaged parts. Before further use of the
tool, a guard
or other part that is damaged should be carefully checked
to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard
or other part that is damaged must be properly repaired or
replaced by a qualifed service center to avoid risk of personal
injury.
Never leave tool running unattended. Turn power off.
Don’t leave tool until it comes to a complete stop.
Keep the engine free of grass, leaves, or grease to reduce
the chance of a fire hazard.
Keep the exhaust pipe free of foreign objects.
Follow manufacturer’s recommendations for safeload-
ing, unloading, transport, and storage of machine.
Be thoroughly familiar with controls. Know how to stop
the product and bleed pressure quickly.
Keep tool dry, clean, and free from oil and grease. Always
use a clean cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any solvents to
clean tool.
Stay alert and exercise control. Watch what you are doing
and use common sense. Do not operate tool when you are
tired. Do not rush.
Do not operate the product while under the influence of
drugs, alcohol, or any medication.
Check the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire, or string which can
be thrown or become entangled in the machine.
Do not use tool if switch does not turn it off. Have switch
replaced by a qualified service center.
Before cleaning, repairing, or inspecting, shut off the
engine and make certain all moving parts have stopped.
Disconnect the spark plug wire, and keep the wire away
from the plug to prevent accidental starting.
Avoid dangerous environment. Don’t use in damp or wet
locations or expose to rain. Keep work area well lit.
Never use in an explosive atmosphere. Normal sparking
of the motor could ignite fumes.
Do not operate while smoking or near an open flame.
Do not operate around dry brush, twigs, cloth rags, or other
flammable materials.
WARNING: Risk of injection or injury – Do not direct dis-
charge stream at persons.
IMPORTANT SAFETY INSTRUCTIONS
Page 3 — English
Use caution when positioning the pressure washer for
use. Warm air from the engine could cause discolored spots
on grass.
Never direct a water stream toward people or pets, or
any electrical device.
Before starting any cleaning operation, close doors and
windows. Clear the area to be cleaned of debris, toys, out-
door furniture, or other objects that could create a hazard.
Never pick up or carry a machine while the engine is
running.
Never start the machine if ice has formed in any part of the
equipment.
Do not use acids, alkalines, solvents, flammable material,
bleaches, or industrial grade solutions in this product.
These products can cause physical injuries to the operator
and irreversible damage to the machine.
Always operate the machine on a level surface. If the engine
is on an incline, it could seize due to improper lubrication
(even at the maximum lubricant level).
WARNING: High pressure jets can be dangerous if sub-
ject to misuse. The jet must not be directed at persons,
animals, electrical devices, or the machine itself.
Hold the trigger handle securely with both hands. Expect
the trigger handle to move when the trigger is pulled due to
reaction forces. Failure to do so could cause loss of control
and injury to yourself and others.
Never attempt to make any adjustments while the engine
(motor) is running (except where specifically recommended
by the manufacturer).
Protective covers must always cover rotating parts when
the engine is running.
Keep cooling air intake (starter grip and rope area) and
muffler side of the engine at least 3 feet away from buildings,
obstructions, and other combustible objects.
Keep the engine away from flammables and other haz-
ardous materials.
Keep away from hot parts. The muffler, exhaust gases,
and other engine parts become very hot. Do not touch the
muffler or place any body parts in the path of hot exhaust
gases, which can cause burns and other serious personal
injuries.
Do not touch the spark plug and ignition cable when
starting and operating the engine.
Check fuel hoses and joints for looseness and fuel leakage
before each use.
Check bolts and nuts for looseness before each use. A
loose bolt or nut may cause serious engine problems.
Always refuel outdoors. Never refuel indoors or in a poorly
ventilated area.
Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present, such
as hot water and space heaters, clothes dryers, and the like.
If the fuel tank has to be drained, do this outdoors into a
container approved for gasoline and away from all igni-
tion sources.
To reduce the risk of fire and burn injury, handle fuel with
care. It is highly flammable.
Do not smoke while handling fuel.
Add fuel before starting the engine. Never remove the
cap of the fuel tank or add fuel while the engine is running
or when the engine is hot.
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
Replace all fuel tank and container caps securely.
Wipe spilled fuel from the unit. Move 30 feet away from
refueling site before starting engine.
If fuel is spilled, do not attempt to start the engine, but move
the machine away from the area of spillage and avoid creat-
ing any source of ignition until fuel vapors have dissipated.
Never attempt to burn off spilled fuel under any
circumstances.
Before storing, allow the pressure washer to cool for 30
minutes and drain fuel from the unit.
Store fuel in a cool, well-ventilated area, safely away from
spark and/or flame-producing equipment.
Store fuel in containers specifically designed for this pur-
pose.
Empty fuel tank and restrain the unit from moving before
transporting in a vehicle.
When servicing use only recommended or equivalent
replacement parts. Use of any other parts may create a
hazard or cause product damage.
ONLY use cold water.
Make sure minimum clearance of 3 feet is maintained from
combustible materials.
Never spray close to the surface to be cleaned as you can
damage the surface.
After stopping the engine, always pull the trigger on the
trigger handle to relieve stored pressure in the high pres-
sure hose. Failure to do so could result in serious personal
injury.
For outdoor use only.
Ensure the high pressure hose is properly connected
before using the product.
Save these instructions. Refer to them frequently and use
them to instruct other users. If you loan someone this tool,
loan them these instructions also.
SPECIFIC SAFETY RULES
Page 4 — English
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe
operation of this product.
SYMBOL NAME EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection
Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Wet Conditions Alert
Do not expose to rain or use in damp locations, and never direct
a water stream toward any electrical device.
Hot Surface and Exhaust Gases
To reduce the risk of injury or damage, avoid contact with any
hot surface and do not place any body parts in the path of hot
exhaust gases.
Risk of Injections
To reduce the risk of injection or injury, never direct a water
stream towards people or pets or place any body part in the
stream. Leaking hoses and fittings are also capable of causing
injection injury. Do not hold hoses or fittings.
Risk of Explosion
Do not spray flammable liquids. Flammable liquids, fuel, and
their vapors are explosive and can cause severe burns or death.
Risk of Fire
Do not add fuel when the product is operating or still hot. Fire
can cause severe burns or death.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates a hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING:
Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION:
Indicates a hazardous situation, that, if not avoided, may result in minor or
moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).
SYMBOLS
Page 5 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe
operation of this product.
SYMBOL NAME EXPLANATION
Toxic Fumes
Running this product indoors can result in death due to carbon
monoxide, a poison gas you cannot see or smell. Never oper-
ate indoors, even if windows and doors are open. Only use
outdoors and at least 20 feet away from windows, doors, and
openings or vents.
Kickback
To reduce the risk of injury from kickback, hold the spray wand
securely with both hands when the machine is on.
Electric Shock Do not use near electric power lines or receptacle outlets.
Chemical Burns
To reduce the risk of injury or damage, DO NOT USE ACIDS,
ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,
OR INDUSTRIAL GRADE SOLUTIONS in this product.
PRODUCT SPECIFICATIONS
Engine............................................................................................................................................................................173cc
Fuel Tank Capacity ....................................................................................................................................................0.25 gal.
Lubricant Fill Volume ..................................................................................................................................................... 18 oz.
Spark Plug ...........................................................................................................................................LG F6TC or equivalent
Maximum Pounds Per Square Inch Pressure* ......................................................................................................... 2,900 psi
Maximum Gallons Per Minute* ...................................................................................................................................2.3 gpm
Maximum Inlet Water Temperature ................................................................................................................................ 104˚F
*Max. rating determined by PWMA Standard PW101
FEATURES
KNOW YOUR PRESSURE WASHER
See Figure 1.
The safe use of this product requires an understanding of the
information on the tool and in this operator’s manual as well
as a knowledge of the project you are attempting. Before use
of this product, familiarize yourself with all operating features
and safety rules.
5-IN-1 CHANGE-OVER NOZZLE
The 5-in-1 Change-over Nozzle makes it easy to change
spray patterns.
AUTOMATIC SOAP INJECTION SYSTEM
Place the soap injection hose with filter into your desired
pressure washer detergent to apply detergent quickly and
easily to your cleaning project. Use of a soap setting on the
nozzle will activate the soap injector at a 20:1 dilution ratio.
FUEL TANK
This fuel tank has a maximum capacity of 0.25 gal. Use un-
leaded automotive gasoline in the engine.
Page 6 — English
HOSE STORAGE
Once the high pressure hose is rolled, hang it on the back
of the machine using the stretch strap to secure in place.
STOP SWITCH
The stop switch is used to turn the engine off.
STARTER GRIP AND ROPE
The starter grip and rope is pulled to start the machine.
THERMAL RELIEF VALVE
This pump feature will prevent water temperatures from
reaching harmful levels by releasing a small amount of
water. Once the water has drained, the thermal relief valve
will reset itself.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides
added control of the spray wand and helps reduce fatigue.
TRIGGER WITH LOCK OUT
Pulling the trigger releases a stream of water for high
pressure cleaning. The lock out provides protection against
unauthorized use.
FEATURES
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-800-860-4050 for assistance.
PACKING LIST
Pressure Washer
35 ft. High Pressure Hose
Trigger Handle
Spray Wand
5-in-1 Change-over Nozzle
Soap Injection Hose
4-Cycle Engine Lubricant (SAE 30 or SAE 10W30)
Disposable Funnel
Handle
Operator’s Manual
WARNING:
If any parts are damaged or missing do not operate this
tool until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
INSTALLING THE HANDLE
See Figure 2.
CAUTION:
Be careful to avoid pinching your fingers or hands when
installing the handle onto the frame.
Push and hold the button on the handle as you slide the
handle into the holes in the frame.
NOTE: Before use, pull the handle up until the lock
button snaps through the locking slot to secure the
handle in place.
Page 7 — English
CONNECTING THE SPRAY WAND TO THE
TRIGGER HANDLE
See Figure 3.
Place the threaded end of the spray wand in the connec-
tor on the end of the trigger handle.
Turn the connector until it stops to secure the spray wand
in place.
CONNECTING THE HIGH PRESSURE HOSE
TO THE TRIGGER HANDLE
See Figure 4.
Screw the collar on the high pressure hose into the
trigger handle inlet coupler by turning the hose collar
clockwise. Tighten securely.
NOTE: Be careful to avoid cross-threading, which can
cause the trigger handle to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE
TO THE PUMP
See Figure 5.
Completely uncoil and straighten the high pressure hose
to prevent kinks.
NOTE: See Using the High Pressure Hose in Operation
for more information about using the high pressure hose.
Align the collar on the hose to the threaded outlet on the
pump.
Install the end of the high pressure hose collar onto the
threaded outlet.
Turn the collar clockwise to tighten the hose securely to
the pump.
NOTE: Be careful to avoid cross-threading, which can
cause the hose to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 6.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water sup-
ply to prevent the feedback of chemicals into the drinking
water supply. Direct connection through a receiver tank
or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose to the pressure washer:
Run water through the hose for 30 seconds to clean any
debris from the hose.
Inspect the screen in the water intake.
If the screen is damaged, do not use the machine until
the screen has been replaced.
If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 10 feet of unrestricted
hose between the pressure washer intake and the hose
faucet or shut off valve (such as a “Y” shut off connector).
With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
ASSEMBLY
DO NOT OVERTILT THE UNIT!
Page 8 — English
Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills, play-
ground equipment, etc.
*Always test in an inconspicuous area first.
ADDING/CHECKING ENGINE LUBRICANT
See Figure 7.
NOTE: This machine has been shipped with approximately
2 oz. of lubricant in the engine from testing. You must add
lubricant to the engine before starting it the first time.
NOTICE:
Any attempt to start the engine without adding lubricant
will result in engine failure.
To add engine lubricant:
Place pressure washer on a flat, level surface. Do not tilt.
Unscrew the oil cap/dipstick by turning counter-
clockwise.
Before first use, pour all but 2 oz. of the provided lubricant
into the engine through the oil fill hole. Check and add
additional lubricant as needed until the level reaches the
upper portion of the hatched area on the dipstick. Do not
overfill.
Replace the oil cap/dipstick and securely tighten.
To check engine lubricant level:
Place pressure washer on a flat, level surface. Do not tilt.
Unscrew the oil cap/dipstick by turning counter-
clockwise.
Wipe dipstick clean and re-seat in hole; do not rethread.
Remove dipstick again and check lubricant level. Lubricant
level should fall within the hatched area on the dipstick.
If level is low, add 4-stroke engine lubricant (SAE 30 or
SAE 10W30) until the level reaches the upper portion of
the hatched area on the dipstick. Do not overfill.
Replace and secure the oil cap/dipstick.
NOTICE:
Do not overfill. Overfilling the crankcase may cause ex-
cessive smoke and engine damage.
WARNING:
Do not allow familiarity with tools to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this tool. The use of at-
tachments or accessories not recommended can result
in serious personal injury.
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to follow these instructions
could result in serious injury, electric shock, or death.
WARNING:
Risk of serious burns. Do not touch the muffler or place
any body parts in the path of hot exhaust gases, which
can cause burns and other serious personal injuries.
NOTICE:
This product is not equipped with a spark arrestor and
cannot be used on U.S. forest lands; in addition, product
users must comply with Federal, State, and local fire pre-
vention regulations. Check with appropriate authorities.
Contact customer service or a qualified service center to
purchase a spark arrestor.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or a quali-
fied service center for assistance.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
OPERATION
Page 9 — English
Insert a clean funnel into the fuel tank then slowly pour gas-
oline into the tank. Fill tank to approximately 1-1/2 in. below
the top of the tank neck (this allows for fuel expansion).
Replace fuel cap and tighten securely.
Clean up any spills before starting the engine.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figures 9 - 11.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Before starting the engine:
Connect all hoses.
NOTE: Make sure the pressure washer’s water intake
screen is in place and unclogged before connecting
garden hose.
Check all fluids (lubricant and gas).
Turn on the garden hose then squeeze the trigger to
relieve air pressure; hold the trigger until a steady stream
of water appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the engine:
Turn the fuel valve to the OPEN position.
Move the choke to the CHOKE position.
NOTE: If restarting after a brief stop (i.e., after refueling
or moving), leave the choke lever in the RUN position.
Grasp the starter grip and pull slowly until resistance is
felt. Give the starter grip and rope a short, brisk pull to
start the engine.
NOTE: Do not allow the starter grip and rope to snap
back after starting; return it gently to its original place.
NOTICE:
If the starter grip and rope becomes difficult to pull,
squeeze the trigger to relieve water pressure before at-
tempting to start the engine again.
Allow the engine to run for 5 seconds, then move the
choke to the RUN position.
ETHANOL-BLENDED FUELS
NOTICE:
Do not use E15 or E85 fuel in this product. It is a viola-
tion of federal law and will damage the unit and void
your warranty. Only use unleaded gasoline containing
up to 10% ethanol.
ADDING GASOLINE TO THE FUEL TANK
See Figure 8.
DANGER:
Risk of fire and serious burns: Never remove fuel cap
when unit is running. Shut off engine and allow the unit
to cool at least five minutes. Remove cap slowly.
WARNING:
Gasoline and its vapors are highly flammable and
explosive. To prevent serious personal injury and prop-
erty damage, handle gasoline with care. Keep away from
ignition sources, handle outdoors only, do not smoke
while adding fuel, and wipe up spills immediately.
WARNING:
Always shut off engine before fueling. Never remove
fuel cap or add fuel to a machine with a running or hot
engine. Make sure the unit is sitting on a flat, level sur-
face and only add fuel outdoors. If the engine is hot, let
the unit cool for at least five minutes before adding fuel.
After fueling, immediately replace fuel cap and tighten
securely. Move at least 30 ft. from refueling site before
starting engine. Do not smoke and stay away from open
flames and sparks! Failure to follow these instructions
could result in a fire and cause serious personal injury.
WARNING:
Check for fuel leaks. A leaking fuel cap, tank, or line is a
fire hazard and must be replaced immediately. If you find
any leaks, correct the problem before using the product.
Failure to do so could result in a fire that could cause
serious personal injury.
NOTE: This is a 4-cycle engine. DO NOT mix fuel and
lubricant together.
Turn the fuel valve to the CLOSED position.
Mix fuel stabilizer with gasoline according to fuel stabilizer
manufacturer’s directions.
Before removing the fuel cap, clean the area around it.
Remove the fuel cap.
OPERATION
Page 10 — English
OPERATION
NOTICE:
Routinely make a visual inspection of the pump and
engine during use. If you notice any lubricant leaking
around the pump or engine seals, stop using the pres-
sure washer immediately. Contact customer service or
a qualified service center for repair. Failure to do so may
cause property damage.
To stop the engine:
Press and hold the STOP switch until the engine stops.
Turn the fuel valve to the CLOSED position.
NOTE: Shutting off the engine will not relieve pressure in the
system. Pull trigger to release water pressure.
WARNING:
While operating and storing, keep at least 3 feet of clear-
ance on all sides of this product, including overhead. Al-
low a minimum of 30 minutes of “cool down” time before
storage. Keep all body parts, clothing, combustible ma-
terials, and hoses away from the muffler. Heat created by
muffler and exhaust gases could be hot enough to cause
serious burns, ignite combustible objects, and/or damage
high pressure hoses that can result in an injection injury.
USING THE TRIGGER HANDLE
See Figure 12.
WARNING:
Hold the trigger handle securely with both hands. Expect
the trigger handle to move when the trigger is pulled due
to reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
Pull back and hold the trigger to operate the pressure
washer.
Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:
Push up on the lock out until it clicks into the slot.
To disengage the lock out:
Push the lock out down and into its original position.
Start with the nozzle 1–2 ft. away from the cleaning surface
and carefully approach the surface just until the desired
level of cleaning is achieved. If the spray is too close it can
damage the cleaning surface.
ABRASIVE GENTLE
NOZZLE SELECTION GUIDE
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
LOW PRESSURE
(FOR SOAP OR
GENTLE RINSE)
0º
25º 40º
Long Range
Short Range
Concrete, Brick, Masonry
Siding, Gutters, House
Fencing, Deck, Patio
Lawn Equipment, Boat, RV
Recommended Nozzle Use With Caution for Certain Applications
Page 11 — English
INSTALLING/REMOVING NOZZLE
See Figure 13.
WARNING:
NEVER remove nozzles without first turning off the
engine, relieving the water pressure in the trigger
handle, and locking the lock out on the trigger handle.
NEVER point the nozzle at your face or at others. The
quick-connect feature contains small springs that could
eject the nozzle with some force. Failure to follow these
instructions could result in an eye injury or other serious
personal injury.
To connect the nozzle to the trigger handle:
Turn off the pressure washer and shut off the water sup-
ply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Push the nozzle into the quick-connect collar until it clicks
in place and is secured properly.
To disconnect the nozzle from the trigger handle once
the cleaning job is complete:
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar.
USING THE 5-IN-1 CHANGE-OVER NOZZLE
See Figure 14.
There are five spray pattern settings located on the 5-in-1
Change-over Nozzle. To select a spray pattern, rotate the
spray selector to the desired setting. Refer to the Nozzle
Selection Guide for more information about which setting
to choose.
USING THE HIGH PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high pres-
sure hose prior to and during each use and do not allow
it to become kinked. The high pressure hose features an
outer covering that provides strength to the hose. If the
outer covering becomes damaged, stop using the hose
and replace it immediately. A kinked or damaged hose
can develop a high pressure leak and result in a possible
injection or other serious personal injury.
To prevent damage to the outer covering:
Inspect the hose before every use.
Fully unwrap and straighten hose before use.
Do not allow the high pressure hose to be kinked.
Keep hose away from hot surfaces and sharp edges.
Do not pull unit by high pressure hose.
Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 15 - 17.
As sold, this unit is designed for use with “downstream” pres-
sure washer detergents. To convert for use with “upstream”
detergents. Contact customer service or a qualified service
center for more information.
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRES-
SURE WASHERS. Do not use household detergents,
acids, alkalines, bleaches, solvents, flammable material,
or industrial grade solutions, which can damage the
pump or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
Place the open end of the soap injection hose over the
barbed fitting on the pump.
Remove the cap from the soap container and place the
soap injection hose with filter in the container.
NOTE: The machine setting of this unit is 20:1, which usu-
ally allows the use of 1 gallon pressure washer detergent
without further dilution. Check your detergent instructions
to be sure additional dilution is not necessary.
Install 5-in-1 Change-over Nozzle (if necessary). Rotate
the spray selector on the nozzle to either the blue short
range detergent ( ) or blue long range detergent ( )
setting.
Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
For long range detergent application:
With the nozzle installed on the spray wand and the engine
shut off, rotate the spray selector to the long range detergent
[ ] setting.
For short range detergent application:
With the nozzle installed on the spray wand and the engine
shut off, rotate the spray selector to the short range detergent
[ ] setting.
Before shutting off the engine:
Place the soap injection hose with filter in a bucket of
clean water.
OPERATION
Page 12 — English
OPERATION
Spray the clear water through the spray wand until the
bucket is empty.
If any detergent remains in the spray, repeat with a second
bucket of clean water.
Shut off the engine.
NOTE: Shutting off the engine will not relieve pressure in the
system. Pull trigger to release water pressure.
RINSING WITH THE PRESSURE WASHER
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Remove the soap injection hose, if installed.
Select the right nozzle setting for the job. See the chart
shown earlier in the manual to select the appropriate
nozzle setting.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
USING PUMP PROTECTOR
See Figure 18.
Regular use of a commercially available pump protector
prolongs the life of the pressure washer by removing hard
water mineral deposits, lubricating pump seals and pistons,
and preventing freeze damage. Pump protector should be
added to the unit after every use and before storage. Pump
protector can be purchased at the retailer where you pur-
chased your pressure washer, or by calling customer service.
The instructions that follow are typical for adding pump pro-
tector but you should always verify the specific instructions
provided by the manufacturer of the pump protector used.
Turn off the pressure washer engine and shut off the water
supply. Pull trigger to release water pressure.
Disconnect garden hose and high pressure hose.
Unscrew threaded top from pump protector bottle and
remove paper seal from bottle. Reinstall top on bottle and
tighten securely.
NOTE: The rubber seal should remain inside the threaded
top. If it comes out, be sure to replace before reinstalling
the top.
Remove bottle cap and attach threaded end of bottle
securely to pressure washer pump water intake.
Squeeze bottle to inject contents into pump.
With engine switch off, pull starter grip and rope to cycle
pump, then squeeze bottle again to guarantee complete
coverage.
Pump is protected when the protector fluid exits the pump
outlet.
MOVING THE PRESSURE WASHER
See Figure 19.
NOTE: Never lift or carry this product using the handle.
Turn the pressure washer off.
Tilt the machine toward you slightly until it balances on
the wheels then roll the machine to the desired position.
Do not tilt forward or sideways when moving.
DO NOT attempt to move the unit by pulling on any of
the hoses.
HIGH ALTITUDE OPERATION
Your engine is configured for operation below 2000 feet
altitude at the factory. Your engine must be reconfigured for
operation above 2000 feet altitude. Operating the engine
with the wrong engine configuration at a given altitude may
increase its emissions, decrease fuel efficiency, degrade per-
formance, and cause irreversible damage. Engines configured
for high altitude operation cannot be operated in standard
altitude conditions. A qualified service center should ensure
that your engine is properly configured for your location.
Page 13 — English
MAINTENANCE
Normal maintenance, replacement or repair of emission con-
trol devices and systems may be performed by any qualified
repair establishment or individual with original or equivalent
parts. Warranty and recall repairs must be performed by an
authorized service center; please contact customer service
for assistance.
WARNING:
Before inspecting, cleaning or servicing the machine, shut
off engine, wait for all moving parts to stop, and discon-
nect spark plug wire and move it away from spark plug.
Allow 30 minutes of cool down time before performing
any maintenance. Failure to follow these instructions
can result in serious personal injury or property damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
When servicing, use only recommended or equivalent
replacement parts. Use of any other parts could create
a hazard or cause product damage.
NOTICE:
This product is not equipped with a spark arrestor and
cannot be used on U.S. forest lands; in addition, product
users must comply with Federal, State, and local fire pre-
vention regulations. Check with appropriate authorities.
Contact customer service or a qualified service center to
purchase a spark arrestor.
NOTICE:
Periodically, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts,
caps, etc. Tighten securely all fasteners and caps and
do not operate this product until all missing or damaged
parts are replaced. Please contact customer service or
a qualified service center for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which could result in serious personal
injury.
Before running the engine, perform the following pre-
operation steps:
Check that all bolts, nuts, etc., are securely tightened.
Make sure the air filter is clean.
Check both the engine lubricant level and the fuel tank
level; refill as needed.
Inspect the work area for hazards.
If there is excessive noise or vibration, stop the unit im-
mediately.
NOZZLE MAINTENANCE
See Figure 20.
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Remove the nozzle from the spray wand.
WARNING:
NEVER remove nozzles without first turning off the en-
gine, relieving the water pressure in the trigger handle,
and locking the lock out on the trigger handle. NEVER
point the nozzle at your face or at others. The quick-
connect feature contains small springs that could eject
the nozzle with some force. Failure to follow these in-
structions could result in an eye injury or other serious
personal injury.
To free any foreign materials clogging or restricting the
nozzle, blow out or remove debris with a straightened
paper clip or fine needle (not included).
Using a garden hose, flush debris out of nozzle by back
flushing (running the water through the nozzle backwards
or from the outside to the inside).
Reconnect the nozzle to the spray wand.
Turn on the water supply and start the engine.
CHECKING/CLEANING AIR FILTER
See Figure 21.
For proper performance and long life, keep air filter clean.
Release latches on side of air filter cover. Remove cover
and set aside.
Remove the filter element.
Page 14 — English
If the filter element is dirty, clean with warm, soapy water.
Rinse and let dry.
Apply a light coat of engine lubricant to the element, then
squeeze it out.
Replace the element in the air filter unit.
Replace the air filter cover and latch to secure.
NOTE: Do not run the pressure washer without the air filter.
Rapid engine wear will result.
CHECKING THE SPARK PLUG
See Figure 22.
Clean the area around the base of the spark plug before
removing to keep dirt and debris out of the engine.
Remove spark plug.
Clean off carbon deposits on the spark plug electrode
using a plug cleaner or wire brush. Replace the plug if
worn or reuse is questionable. For replacement spark
plug, see Product Specifications earlier in this manual
or the accompanying engine manual, if applicable.
Check electrode gap. The gap should be .028 in.-.032 in.
(0.7- 0.8 mm). Adjust the gap, if necessary, by carefully
bending the ground electrode.
Reinstall spark plug. Tighten securely.
CHANGING ENGINE LUBRICANT
See Figure 23.
Shut off the engine.
Clean the area around the oil fill cap/dipstick, then remove
the oil fill cap/dipstick.
NOTE: Remove the dipstick to allow lubricant to drain
easier and more quickly.
Tilt the pressure washer on its side as shown. Drain lu-
bricant into approved container.
NOTE: Drain the lubricant while the engine is still warm
but not hot. Warm lubricant will drain quickly and more
completely.
WARNING:
Do not change engine lubricant while it is hot. Accidental
contact with hot engine lubricant could result in serious
burns.
After the crankcase is completely drained, return the
pressure washer to an upright position.
Fill with lubricant following the instructions in Adding/
Checking Engine Lubricant earlier in this manual. For
amount of lubricant needed to refill, see Product Specifi-
cations earlier in this manual or the accompanying engine
manual, if applicable.
Before using the pressure washer, check to ensure that
no lubricant is leaking from the engine.
NOTE: Consult hazardous waste management guidelines in
your area for the proper way to dispose of used lubricant.
PUMP LUBRICATION
The pump on this product was lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
PUMP MAINTENANCE
Routinely make a visual inspection of the pump. If you
notice any leaking of lubricant around the pump seals, take
the pressure washer to a qualified service center for repair.
There are no user serviceable parts to the pressure washer
pump. Any attempt to service or alter the pump may damage
the pressure washer and void your product warranty.
STORING THE PRESSURE WASHER
See Figure 24.
NOTE: Regular use of fuel stabilizer and pump protector
will give you better performance of the unit and increase
the life of the pump.
WARNING:
While storing, keep at least 3 feet of clearance on all sides
of this product, including overhead. Allow a minimum of
30 minutes of “cool down” time before storage. Heat cre-
ated by muffler and exhaust gases could be hot enough
to ignite combustible objects.
Store in a dry, covered area where the weather can’t damage it.
It is important to store this product in a frost-free area. Always
empty water from all hoses and the pump before storing.
Drain the fuel tank completely by running the pressure
washer until the gas runs out. Stored gas can go stale in
30 days.
NOTE: Make sure the water supply is connected and
turned on when allowing the pressure washer engine to
run.
Make sure the fuel valve is in the CLOSED position.
Disconnect both the high pressure hose and the garden
hose from the pump.
Empty the pump by pulling on the starter grip and rope
about 6 times. This should remove most of the liquid from
the pump.
NOTICE:
If the location where your pressure washer is stored will
fall below 32°F, the use of a pump protector is required
before storing to prevent freeze damage. Freeze damage
will void your warranty.
MAINTENANCE
Page 15 — English
Remove all hoses. Coil the hoses and store as shown.
Do not allow the hose to become kinked.
Store the unit and accessories in an area that does not
reach freezing temperatures. Do not store near furnace or
other sources of heat that could dry out the pump seals.
PREPARING FOR USE AFTER STORAGE
Pull the starter grip and rope three or four times to clean
lubricant from the combustion chamber.
Remove spark plug from the cylinder. Wipe lubricant from
the spark plug and return it to the cylinder.
Reconnect the spark plug wire.
Refuel the machine as described earlier in the operator’s
manual.
Drain the lubricant and replace with fresh, clean lubricant
as described in Adding/Checking Engine Lubricant in
the Operation section of this manual.
Disconnect spark plug wire and remove the spark plug.
Pour about a teaspoon of clean, air-cooled, four-cycle
lubricant through the spark plug hole into the combustion
chamber.
Leaving the spark plug out, pull the starter grip and rope
two or three times to coat the inside of the cylinder wall.
Inspect the spark plug and clean or replace, as necessary.
Reinstall the spark plug, but leave the spark plug wire
disconnected.
Clean the air filter.
Extend the starter grip and rope to check its condition.
If the rope is frayed, have it replaced immediately by a
qualified service center.
MAINTENANCE
PERIODIC MAINTENANCE SCHEDULE TABLE
NOTE: If a separate engine manual is provided for this pressure washer, please follow the maintenance schedule provided
in the engine manual instead of the maintenance information listed below.
Maintenance Items Each use Weekly 5 hrs 25 hrs 50 hrs 200 hrs
Check for water leaks under manifold, into crankcase X
Plumbing X
Clean engine and check nuts and bolts X
Check and refill engine lubricant X
Check water inlet filter placement
2
X
Add fuel stabilizer X
Add pump protector X
Change engine lubricant
1
X X
Check spark plug X
Clean air filter X
Replace air filter element X
Clean and adjust spark plug and electrodes X
Replace spark plug X
1
Initial lubricant change should be performed after first 5 hours of operation. Thereafter, change lubricant every 50 hours.
2
If water inlet filter is missing or damaged, it must be replaced. See Replacement Parts List available online or call customer
service for part number to order.
NOTE: If you are not sure how to perform any of the maintenance items listed above, take the unit to a qualified service
center to have the maintenance item performed.
Page 16 — English
PROBLEM POSSIBLE CAUSE SOLUTION
Engine fails to start No fuel in tank
Water pressure in hose
Spark plug shorted or fouled
Spark plug is broken (cracked porcelain or elec-
trodes broken)
Ignition lead wire shorted, broken, or disconnected
from spark plug
Ignition inoperative
Choke in wrong position
Engine is flooded
Fill tank.
Squeeze trigger to relieve water pressure.
Replace spark plug.
Replace spark plug.
Replace lead wire or attach to spark plug.
Contact a qualified service center.
Move choke to CHOKE position to start a
cold engine. If engine is warm, choke should
be in RUN position.
Move choke to RUN position and pull the
starter grip and rope repeatedly until the
engine starts.
Engine hard to start Water in gasoline
Weak spark at spark plug
Drain entire system and refill with fresh fuel.
Contact a qualified service center.
Engine lacks power Dirty air filter Clean or replace air filter
Detergent fails to mix with
spray
Spray selector on the 5-in-1 Change-over Nozzle
is set to either the 40º, 25º, or 0º setting
Soap injection hose is not proper ly submerged
Rotate the spray selector on the 5-in-1
Change-over Nozzle to either the short
range detergent [ ] or long range detergent
[ ] setting.
Insert soap injection hose into soap
container.
Pump doesn’t produce
pressure
Spray selector on the 5-in-1 Change-over Nozzle
is set to either the short range detergent [ ] or
long range detergent [ ] setting.
Inadequate water supply
Trigger handle or spray wand leaks
Nozzle is clogged
Air in line
Hose is leaking
Kink in hose
Pump is faulty
Rotate the spray selector on the 5-in-1
Change-over Nozzle to either the 40º, 25º,
or 0º setting.
Provide adequate water flow.
Check connections and/or replace trigger
handle or spray wand.
Clean nozzle.
Squeeze trigger on trigger handle to remove
air from line.
Replace hose.
Eliminate kinks in hose.
Contact a qualified service center.
TROUBLESHOOTING
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Ryobi RY802900VNM Le manuel du propriétaire

Ryobi
Marque
Ryobi
Modèle
RY802900VNM
Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents