Agrowtek RX1i Manuel utilisateur

Marque: Agrowtek

Modèle: RX1i

Taper: Manuel utilisateur

1© Agrowtek Inc. | www.agrowtek.com | Technology to Help You Grow™

Technology to Help You Grow

AGROWtEK

Digital Intelligent Outlet Relay

Contents

Installation Instructions 2

Mounting the RX1i Relay 2

Installation Notes 3

Connection to GrowControl™ GCX 3

GrowNET™ Hubs 3

Connection to USB AgrowLINK 4

Connection to MODBUS RTU 4

Serial Speed & Format 5

Supported Commands 5

MODBUS Register Map 5

Technical Information 6

Troubleshooting 6

Maintenance & Service 6

Storage and Disposal 6

Warranty 6

Specications

Input Power (GrowNET™) 1 W @ 12-24Vdc

Max Current 12A @ 120Vac ~

HP Rating 1/2HP (8FLA @ 120Vac ~ )

Frequency 60 Hz

Receptacle Type NEMA 5-15R

Independent Relays 1

Status Indicators Red LED

Enclosure Knock-Outs (2) dia. 7/8”

Enclosure Rating IP40

Minimum Cycle Time 1 second

Interface GrowNET™, MODBUS

Relay Ratings 100,000 cycles

Relay Cycle Counters Up to 4 billion cycles per relay

INSTRUCTION MANUAL

RX1i

KEEP THESE INSTRUCTIONS

The RX1i intelligent relay is designed to be plugged into a stan-

dard 120Vac wall outlet mounted on a vertical wall surface.

A screw tab is provided which can be used to x the relay to the

wall outlet preventing accidental disconnection from the recep-

tacle.

Equipment to be controlled is then plugged into the outlet on

the RX1i. When the RX1i is activated, power will be switched to

the outlet on the RX1i from the wall outlet.

Mounting the RX1i Relay

General Notes:

1. Install into a vertical receptacle with the RJ45 connection facing down to maintain enclosure rating.

2. Device is not intended for use with an extension cord.

3. For indoor use and installation only.

Installation Instructions

DANGER Electrocution Hazard

Always un-plug the relay module before servicing or wiring; ensure all power is disconnected. For continued protection against

electric shock plug into grounded outlets only and do not remove the ground pin. Install all electrical equipment and wiring in

accordance with national and local electric codes. For indoor use in dry locations only (0-80% RH non-condensing.) Do not open

the relay; there are no user-serviceable parts inside.

DANGER Risque d’électrocution

Toujours non brancher le module de relais avant l’entretien ou le câblage; assurer l’alimentation est débranché. Pour une protec-

tion continue contre le bouchon de choc électrique dans des prises mises à la terre et ne pas retirer la broche de terre. Installez

tous les équipements électriques et le câblage conformément aux codes électriques nationaux et locaux. Pour une utilisation en

intérieur dans des endroits secs seulement (0-80% sans condensation.) Ne ouvrez pas le relais; il n’y a aucune pièce réparable par

l’utilisateur.

NOTICE:

Plug the relay fully ush into a wall receptacle.

Do not plug the relay into an extension cord.

GrowNET™ Hubs

All GrowNET™ devices are connected using standard CAT5 Ethernet cable with RJ-45 connections.

Devices can be connected directly to the GrowNET™ ports on the bottom of the controller, or through HX8

GrowNET™ hubs. It is typical to simplify cabling by locating hubs centrally in hall ways and rooms allowing

single runs from an 8-port device hub back to a central hub or back to the controller.

HX8 GrowNET ™ hubs expand a single port into eight more ports.

Hubs can be daisy-chained to form a network of up to 100 devices per

GrowNET™ bus. Individually buered port transcievers provide excellent

signal integrity and extended communication strength and range.

Hubs provide up to 1A of power for operating sensors and most relays

directly over the CAT5 cable. A DC jack on the hub provides 24Vdc power

to the ports from the included wall power supply. A terminal block

power option is also available.

Refer to the GCX controller manual for details on adding the device to the system.

Connection to GrowControl™ GCX

DIELECTRIC GREASE

Dielectric grease is recommended on RJ-45 GrowNET™ connections when used in humid environments.

Place a small amount of grease onto the RJ-45 plug contacts before inserting into the GrowNET™ port.

Non-conductive grease is designed to prevent corrosion from moisture in electrical connectors.

• Loctite LB 8423 • Dupont Molykote 4/5 • CRC 05105 Di-Electric Grease

• Super Lube 91016 Silicone Dielectric Grease • Other Silicone or Lithium based insulating grease

NOTICE

GrowNET™ ports use standard RJ-45 connections but are NOT compatible the Ethernet network equipment.

Do not connect GrowNET™ ports to Ethernet ports or network switch gear.

Installation Notes

LX1 USB AgrowLINK connects Agrowtek’s devices to a computer’s USB port for:

Connection to USB AgrowLINK

• Firmware Updates

• Manual Operation

• API Based Control

• More

Agrowtek’s intelligent relays may be connected to the LX1 USB AgrowLINK for rmware updates, commu-

nication protocol conguration, addressing and manual operation. Standard drivers automatically install in

Windows for the LX1 USB AgrowLINK.

Connection to MODBUS RTU

RS-485 / RS-422

Use the LX2 ModLINK to connect MODBUS devices to the GrowNET™ port.

RJ45/CAT5

7 - 24 Vdc

3.3/5Vdc Serial Bus Compatible.

Include required bus terminating resistors per EIA standard.

TX/RX+

TX/RX-

PLC

RS-485

LX1

USBGrowNET™ RJ45

Data registers are 16 bits wide with addresses using the standard MODICON protocol. Floating point values

use the standard IEEE 32-bit format occupying two contiguous 16 bit registers. ASCII values are stored with

two characters (bytes) per register in hexadecimal format. Coil registers are single bit values which control

and indicate the status of a relay; 1 being on and 0 being o.

MODBUS Register Map

Parameter Description Type Scale Access Address

Device Address Slave Address Value, 1-247 8 bit R/W 40001

Serial# Serial Number ASCII 8 Char R 40004

DOM Date of Manufacture ASCII 8 Char R 40008

HW Version Hardware Version ASCII 8 Char R 40012

FW Version Firmware Version ASCII 8 Char R 40016

Timeout (seconds) Turn o relay if no comms Value 16 bit R/W 41001

Relay 1 Count Operation Cycle Count Value 32 bit R 49001

Relay Coil 1 Relay Coil Coil 1 bit R/W 1

0x01 Read Coils

0x03 Read Multiple Registers

0x05 Write Single Coil

0x06 Write Single Register

A request to use a function that is not available will return an illegal function exception.

Supported Commands

Serial Speed & Format

The default serial data format for the LX2 ModLINK interface is: 19,200 baud, 8-N-1.

Alternate speeds and formats between 9,600 - 115,200 baud may be congured with the free AgrowLINK PC

utility using a LX1 USB AgrowLINK and the cross-over adapter supplied with the LX2 ModLINK.

MODBUS Manual

See MODBUS manual for more information.

LX2 ModLINK™LX1 USB AgrowLINK™

GrowNET™

Cross-Over

7 - 24 Vdc

USB

A request to read or write a register that is not available will return an illegal address exception.

Technical Information

Agrowtek Inc. warrants that all manufactured products are, to the best of its knowledge, free of defective material and workman-

ship and warrants this product for 1 year from the date of purchase. This warranty is extended to the original purchaser from the

date of receipt. This warranty does not cover damages from abuse, accidental breakage, or units that have been modied, altered,

or installed in a manner other than that which is specied in the installation instructions. Agrowtek Inc. must be contacted prior to

return shipment for a return authorization. No returns will be accepted without a return authorization. This warranty is applicable

only to products that have been properly stored, installed, and maintained per the installation and operation manual and used for

their intended purpose. This limited warranty does not cover products installed in or operated under unusual conditions or envi-

ronments including, but not limited to, high humidity or high temperature conditions. The products which have been claimed and

comply with the aforementioned restrictions shall be replaced or repaired at the sole discretion of the Agrowtek Inc. at no charge.

This warranty is provided in lieu of all other warranty provisions, express or implied. It is including but not limited to any implied

warranty of tness or merchantability for a particular purpose and is limited to the Warranty Period. In no event or circumstance

shall Agrowtek Inc. be liable to any third party or the claimant for damages in excess of the price paid for the product, or for any

loss of use, inconvenience, commercial loss, loss of time, lost prots or savings or any other incidental, consequential or special

damages arising out of the use of, or inability to use, the product. This disclaimer is made to the fullest extent allowed by law or

regulation and is specically made to specify that the liability of Agrowtek Inc. under this limited warranty, or any claimed exten-

sion thereof, shall be to replace or repair the Product or refund the price paid for the Product.

Warranty

Exterior Cleaning

Exterior may be wiped with a damp cloth wish mild dish detergent, then wiped dry. Disconnect power be-

fore cleaning the enclosure to prevent electrical shock.

Fuse Replacement

There are no fuses or servicable components inside the RX1i. Do not open the enclosure.

Maintenance & Service

Storage and Disposal

Relays are not activating, no power LED on PCB

Ensure the relay is plugged into 120VAC outlet and the power is on to the outlet.

Relays are clicking but no power to an outlet

Check the status LED to determine if AC power is reaching the line terminal of the receptacle. The red LED is

passed through the relay to the terminal. If the status LED for the receptacle is on, check the equipment by

bypassing the relay.

Troubleshooting

Storage

Store equipment in a clean, dry environment with ambient temperature between 10-50°C.

Disposal

This indsutrial control equipment may contain traces of lead or other metals and environmental contami-

nants and must not be discarded as unsorted municipal waste, but must be collected separately for the

purpose of treatment, recovery and environmentally sound disposal. Wash hands after handling internal

components or PCB’s.

Agrowtek RX1i Manuel utilisateur

Marque: Agrowtek

Modèle: RX1i

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Agrowtek RX1i User manual

Agrowtek RX1i Manuel utilisateur

Agrowtek RX1i Manuel utilisateur

dans d''autres langues

Autres documents