KitchenAid 36" Installation Instructions And Use & Care Manual

Marque: KitchenAid

Modèle: 36"

Catégorie: Fours

Taper: Installation Instructions And Use & Care Manual

Ce manuel convient également à

30" (76.2 CM) AND 36" (91.4 CM)

SLIDE-OUT VENT RANGE HOOD

Installation Instructions and Use & Care Guide

HOTTE D’EXTRACTION AVEC MODULE DE

COMMANDE EXTRACTIBLE 30" (76,2 CM) ET 36"

(91,4 CM)

Instructions d’installation et Guide d’utilisation et d’entretien

Table of Contents/Table des matières.............................................................................2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

IMPORTANT:

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

Save installation instructions for local electrical inspector's use.

IMPORTANT :

Installateur : Remettre les instructions d'installation au propriétaire.

Propriétaire : Conserver les instructions d'installation pour référence ultérieure.

Conserver les instructions d'installation pour consultation par l'inspecteur local des installations électriques.

9763393

TABLE OF CONTENTS

RANGE HOOD SAFETY .................................................................3

INSTALLATION REQUIREMENTS................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................4

Venting Requirements..................................................................5

Electrical Requirements ...............................................................7

INSTALLATION INSTRUCTIONS..................................................7

Prepare Location..........................................................................7

Install Range Hood ....................................................................10

Make Electrical Connection .......................................................11

Connect the Vent System. .........................................................11

Customized Front Panel.............................................................11

Accessories................................................................................12

RANGE HOOD USE......................................................................13

KWVU Model Series .................................................................13

GZ and IH Model Series.............................................................13

RANGE HOOD CARE...................................................................13

Cleaning......................................................................................13

Replacing the Bulb.....................................................................13

WIRING DIAGRAM .......................................................................14

ASSISTANCE OR SERVICE.........................................................16

In the U.S.A. ...............................................................................16

In Canada ...................................................................................16

WARRANTY ..................................................................................17

TABLE DES MATIÈRES

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................20

EXIGENCES D’INSTALLATION...................................................22

Outillage et pièces......................................................................22

Exigences d’emplacement.........................................................22

Exigences concernant l’évacuation ...........................................23

Spécifications électriques ..........................................................25

INSTRUCTIONS D’INSTALLATION.............................................25

Préparation de l'emplacement...................................................25

Installation de la hotte de cuisinière ..........................................28

Raccordement électrique...........................................................29

Raccordement du circuit d'évacuation......................................29

Panneau avant personnalisé......................................................29

Accessoires ................................................................................30

UTILISATION DE LA HOTTE DE CUISINIÈRE...........................31

Modèles Séries KWVU ..............................................................31

Modèles Séries GZ et IH............................................................31

ENTRETIEN DE LA HOTTE DE CUISINIÈRE .............................31

Nettoyage ...................................................................................31

Remplacement de la lampe .......................................................31

SCHÉMA DE CÂBLAGE...............................................................32

ASSISTANCE OU SERVICE.........................................................33

GARANTIE.....................................................................................34

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

■ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

■ Before servicing or cleaning the unit, switch the power off at

the service panel disconnecting means to prevent power

from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service

panel.

■ Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

& standards, including fire-rated construction.

■ Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

■ When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

■ Ducted systems must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls ceilings, attics, crawl spaces, or

garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

■ Never leave the surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

■ Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

■ Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

■ Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:

■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or

other metal tray, then turn off the gas burner or electric

element. BE CAREFUL TO PREVENT BURNS. If the

flames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

■ NEVER PICK UP A FLAMING PAN - you may be burned.

■ DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

■ Use an extinguisher ONLY if:

– You know you have a class ABC extinguisher, and you

already know how to operate it.

– The fire is small and contained in the area where it

started.

– The fire department is being called.

– You can fight the fire with your back to an exit.

Based on "Kitchen Fire Safety Tips" published by NFPA.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the safety instructions provided with any tools

listed here.

Tools needed

■ Level

■ Drill

■ 1¹⁄₄" drill bit

■ ³⁄₈" (8 mm) nut driver or ratchet

■ Pencil

■ Pliers

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Caulking gun and weatherproof caulking compound

■ Phillips screwdriver

■ Flat-blade screwdriver

■ Saber or keyhole saw

■ Duct tape

■ Metal snips

Parts supplied

Check that all parts are included.

■ Literature package

■ 2 screws

■ Damper

■ Plastic cover (used for customized front panel)

■ Hardware package

Parts needed

■ Two ¹⁄₂" (12.7 mm) UL listed or CSA approved conduit

connectors

■ Wall cap for interior-mounted motor

■ Metal vent system

■ Power supply cable

Optional parts needed:

■ Wood filler strips for cabinets with recessed bottoms. Length

and thickness determined by recess dimensions. See

“Prepare Location” section.

■ Two, 1" x 1" x 5" (25.4 x 25.4 x 127 mm) wood pieces for

cabinet floor. See “Prepare Location” section.

■ Four, 1¹⁄₄" (31.8 mm) wood screws

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ Have a qualified technician install the range hood. It is the

installer’s responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial

rating plate is located behind the left filter on the rear wall of

the vent hood.

■ Range hood location should be away from strong draft areas,

such as windows, doors, and strong heating vents.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance. Consult your

cooktop/range manufacturer installation instructions before

making any cutouts.

■ Grounded electrical outlet is required. See “Electrical

Requirements” section.

■ The hood is factory set for vented installations through the

roof or wall.

For recirculating installations, Recirculation Kit Part

Number 883140 is available from your dealer or an

authorized parts distributor.

■ All openings in ceiling and wall where range hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

Installation Clearances

Venting Requirements

■ Vent system must terminate to the outside.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Do not use a 4" (10.2 cm) laundry-type wall caps.

■ Use a metal vent only. A rigid metal vent is recommended. Do

not use plastic or metal foil vent.

■ The size of the vent should be uniform.

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than one elbow is used.

■ Do not install 2 elbows together.

■ The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

■ The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

■ Use duct tape to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around the

cap.

■ Determine which venting method is best for your application.

1 ⁷⁄₁₆"

(5.1 cm)

Shelf extends

FRONT OF

VENT HOOD

11"

(27.9 cm)

¹⁄₈"

(23.2 cm)

(25.4 mm)

7" (17.8 cm)

¹⁄₂"

(24.1 cm)

1 ⁵⁄₈"

(41.3 mm)

⁵⁄₈" to 2 ¹⁄₈"

(1.6 cm to 5.4 cm)

30" (76.2 cm) model: 29 ⁷⁄₈" (75.9 cm)

36" (91.4 cm) model: 35 ⁷⁄₈" (91.1 cm)

30" (76.2 cm) model: 13" (33.0 cm)

36" (91.4 cm) model: 16" (40.6 cm)

30" (76.2 cm) model: 8" (20.3 cm)

36" (91.4 cm) model: 11" (27.9 cm)

30" (76.2 cm) model: 26" (66.0 cm)

36" (91.4 cm) model: 32" (81.3 cm)

4 ³⁄₈"

(11.1 cm)

¹⁄₄" (8.3 cm)

³⁄₈" (9.5 mm)

(25.4 cm)

³⁄₈"

(6.0 cm)

(5.1 cm)

¹⁄₄"

1 ¹⁄₄"

(31.8 mm)

10"

BACK OF

VENT HOOD

(3.6 cm)

(6.4 mm)

(20.3 cm)

15" (38.1 cm)

min. clearance

upper cabinet

to countertop

13" (33 cm)

cabinet depth

30" (76.2 cm) or

36" (91.4 cm) min.

cabinet opening width

24" (61 cm) min.

30" (76.2 cm)

suggested max.

bottom of hood

to cooking surface

36" (91.4 cm)

base cabinet

height

66"(167.6 cm)

max.

to bottom of

cabinet frame

Venting Methods

The vent system needed for installation is not included.

A 3¹⁄₄" x 10" (8.3 cm x 25 cm) rectangular vent system is

recommended.

Calculate Vent System Length

The recommended vent system length is 3¹⁄₄" x 10" (8.3 cm x

25 cm) vent with maximum length of 26 ft (8 m) for vent system.

For the best performance, use no more than three 90° elbows.

To calculate the length of the system, add the equivalent feet

(meters) for each of the vent pieces used in the system.

Example vent system

3¹⁄₄" x 10" (8.3 cm x 25 cm)

Recommended Standard Fittings

Recirculating Vent Through the Soffit/Cabinet

This vent hood is factory set for venting through the roof or wall.

For recirculating installations, Recirculation Kit Part

Number 883140 is available from the dealer or an authorized

parts distributor. Damper installation is not required.

Roof Venting Wall Venting

A. 3¹⁄₄" x 10" (8.3 cm x 25 cm)

vent through the roof

B. Roof cap

A. 3

¹⁄₄" x 10" (8.3 cm x 25 cm)

vent through the wall

B. Wall cap

Maximum Length = 26 ft (8 m)

1 - 90° elbow = 5 ft (1.5 m)

1 - wall cap = 0 ft (0 m)

9 ft (2.8 m) straight = 9 ft (2.8 m)

System length = 14 ft (4.3 m)

90˚ elbow

3 ft

(0.93 m)

6 ft (1.8 m)

Wall cap

Vent Piece 3¹⁄₄" x 10" (8.3 cm x 25 cm)

90° elbow 5.0 ft

(1.5 m)

Flat elbow 12.0 ft

(3.7 m)

Wall cap 0.0 ft

(0.0 m)

A. 3¹⁄₄" x 10" (8.3 cm x 25 cm) vent

B. 3

¹⁄₄" x 10" (8.3 cm x 25 cm) elbow

C. Vent cover

D. Soffit

A. Hood

B. Vent system

C. Top of cabinet

D. Vent cover

E. Ceiling or soffit

Electrical Requirements

For GZ or IH model series:

WARNING: To reduce the risk of fire or electrical shock, do not

use this fan with any solid state speed control device.

For KWVU model series:

This fan is suitable for use with solid state speed controls.

IMPORTANT: Observe all governing codes and ordinances. Save

Installation Instructions for electrical inspector’s use.

It is the customer’s responsibility to contact a qualified electrical

installer, and to assure that the electrical installation is adequate

and in conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit is

required.

■ Do not ground to a gas pipe.

■ Check with a qualified electrician if you are not sure the

downdraft vent is properly grounded.

■ Do not have a fuse in the neutral or ground circuit.

■ The range hood must be connected with copper wire only.

■ The range hood should be connected directly to the fused

disconnect (or circuit breaker) box through flexible armored or

nonmetallic sheathed copper cable.

■ Wire sizes (copper wire only) and connections must conform

with the rating of the appliance as specified on the model/

serial rating plate.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

■ A ¹⁄₂" (12.7 mm) UL listed or CSA approved strain relief must

be provided at each end of the power supply cable (at the

range hood and at the junction box).

INSTALLATION INSTRUCTIONS

Prepare Location

It is recommended that the vent system be installed before hood

is installed.

Do not cut a joist or stud unless absolutely necessary. If a joist or

stud must be cut, then a supporting frame must be constructed.

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for vent fittings.

Preparation

1. If possible, disconnect and slowly move the freestanding

range from the cabinet opening to provide easier access to

upper cabinet and rear wall.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Determine and clearly mark a centerline on the underside of

the cabinet.

4. Measure and mark lines as shown for your size of vent hood.

Use a saber saw or keyhole saw to cut an opening through

the underside of the cabinet.

The finished cutout size will be:

30” (76.2 cm) hood - 9¹³⁄₁₆" x 26¹⁄₈" (23.3 cm x 66.4 cm)

36” (91.4 cm) hood - 9¹³⁄₁₆" x 32¹⁄₈" (23.3 cm x 81.6 cm)

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

A. Centerline

¹⁄₂"

³⁄₁₆"

(3.8 cm)

(23.3 cm)

30" (76.2 cm) hood - 13

¹⁄₁₆"

(33.2 cm)

36" (91.4 cm) hood - 16

¹⁄₁₆"

(40.8 cm)

5. If the cabinet bottom is recessed above a support frame,

wood filler strips need to be installed on the right and left

sides of the cutout to provide sides of clearance for the

sliding screen. Wood filler strips should be flush with or

recessed ¹⁄₁₆"-¹⁄₈" (1.6 mm-3.2 mm) from the bottom of the

support frame.

6. Complete cabinet preparation following the instructions for

your type of installation.

Venting Outside Through the Roof

Measure and mark the lines as shown. Use a saber saw or

keyhole saw to cut a rectangular opening for the vent.

Venting Outside Through the Wall

Assemble the vent that you will use over the vent opening. Do

not attach the vent at this time. Measure from the top of the

screen housing to the top of the vent opening (A) and back to

the bottom of the vent opening (B). Remove the vent.

Transfer measurements A and B to the cabinet back wall.

Measure from the underside of the cabinet or wood filler

strips, if used. Mark the cutout as shown. Use a saber saw or

keyhole saw to cut a rectangular opening for the vent.

Venting Inside Through the Soffit/Cabinet

Measure and mark a rectangular vent opening in the soffit

using the method shown for venting through the wall.

Measure and mark the same centerline on the soffit above the

vent hood area.

Use the grille from the Recirculation Kit or other grille as a

template to outline an opening for the vent. Use a saber saw

or keyhole saw to cut a rectangular opening for the vent

system.

The hood can be vented inside through the top of the cabinet.

The Recirculation Kit Part Number 883140 must be used.

A. Wood filler strips

Cutout

Centerline

(25.4 mm)

(27.3 cm)

³⁄₄"

(10.2 cm)

A. Grille

B. Centerline

Centerline

Cutout

10 ³⁄₄"

(27.3 cm)

Cutout

Centerline

(25.4 mm)

(27.3 cm)

³⁄₄"

(10.2 cm)

7. Install the vent system according to the method needed. Use

caulking to seal the exterior wall or roof opening.

8. Determine wiring knockout.

To wire through the top wiring knockout:

Measure and mark a 10¹⁄₈" (27 cm) line for the 30" (76.2 cm)

hood or 11⁵⁄₈" (29.5 cm) line for the 36" (91.4 cm) hood from

the right of the centerline on the cabinet ceiling. Mark a point

on this line that is 4" (10.2 cm) from the back wall of the

cabinet. Drill a 1¹⁄₄" (3.2 cm) diam. hole through the cabinet

ceiling.

To wire through the rear wiring knockout:

Measure and mark an 11³⁄₈" (29.8 cm) line for the

30" (76.2 cm) hood or 14³⁄₈" (36.5 cm) line for the

36" (91.4 cm) hood from right of the centerline on the cabinet

back wall. Mark the point on this line that is 8¹⁄₄" (21 cm) from

the bottom of the cabinet. Drill a 1¹⁄₄" (3.2 cm) diam. hole

through the wall.

9. Run the wiring through the wall or cabinet according to the

national Electrical Code and all local codes and ordinances.

Use caulking to seal around wire opening.

NOTE: Do not turn on power until installation is complete.

10.

Measure the thickness of the cabinet floor, including the filler

strips, if used. If the thickness is less than

⁵⁄₈

" (15.9 mm), install

wood filler strips that are a minimum length of 5" (12.7 cm)

onto the cabinet floor. The mounting bracket adjusts from

⁵⁄₈

" (15.9 mm) to 2

¹⁄₈

" (54 mm) for the wood filler strips

11. Remove the vent hood from the carton. Attach the damper to

the vent opening. If the roof cap has a damper, do not attach

the damper to the vent hood.

12. Remove the top or rear knockout from the wiring opening to

be used.

A. Wiring cutout

A. Damper

A. Wiring knockouts

Wood fillers

(thickness as required)

Less than ⁵⁄₈" (15.9 mm)

including bottom filler

(if used)

13. Place the vent hood on its back side on a protected surface.

Slide the screen forward. Pull the tabs to remove the filters.

Remove the terminal box cover. Close the screen. Slide the

mounting brackets to the top position.

NOTE: For some installations using the recirculating kit, it

may be easier to attach the vent system to the hood before

lifting the hood into its final position. Seal the connection with

duct tape.

Install Range Hood

1. Lift the vent hood into its final position and feed the electrical

wire through the wiring opening. The mounting brackets

should overlap the cabinet bottom or wood filler strips.

Center the range hood.

2. Check that the front panel is parallel with the cabinet front

when the screen is pushed in. Slide the screen forward.

Tighten the mounting bracket screws so that the vent hood is

secured to the cabinet.

3. Align the hood front panel with the cabinet. Slide the screen

forward. Locate the 2 screws on each side and turn them

counterclockwise to loosen the screws. Adjust the front of the

vent vertically, ³⁄₈" (9.5 mm) up or down, or horizontally,

³⁄₄" (19 mm) front to back, until the front is flush with the

cabinet. Tighten the screws. If it is necessary to adjust the

given dimensions, lower and add or remove the filler strips or

redrill mounting holes.

A. Terminal box cover.

A. Mounting bracket

B. Cabinet bottom

C. Optional wood filler strip

D. Vent hood

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

A. Mounting bracket screw

B. Flat-blade screwdriver

A. Phillips screwdriver

B. Adjustment screws

Make Electrical Connection

1. Connect the white wire of the power supply cable to the white

wire in the hood with a twist-on connector.

2. Connect the black wire of the power supply cable to the

black wire in the hood with a twist-on connector.

3. Connect the green power supply ground wire to the green,

ground screw inside the vent hood terminal box.

4. Replace the terminal box cover.

Connect the Vent System.

1. Vented installations:

Replace the metal filter. Connect the vent system to the hood

vent opening. Seal the connection with duct tape.

Recirculation installations:

Connect the vent system to the hood vent opening. Seal the

connection with duct tape. Follow the instructions included

with Recirculation Kit Number 883140.

2. Turn the power supply on. Slide the screen forward. Check

the operation of the vent hood fan and light. Close the screen.

Customized Front Panel

The front panel of the vent hood can be removed and a

customized front panel added for a more blended look.

KWVU Model Series

It is recommended that a cabinetmaker cut the customized front

panel because of the precise cuts needed for the electronic

control panel.

1. Use the dimensions shown to cut the front panel for either a

30" (76.2 cm) or 36" (91.4 cm) front panel, depending on the

size of your vent hood.

2. Remove the 3 cross-recess screws located behind the front

trim panel in the screen frame.

A. White wires

B. Green ground screw

C. Ground wire

D. Black wires

E. Twist-on connectors

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green ground screw in

terminal box.

Failure to do so can result in death or electrical shock.

A. Filter

panel front face

Section view of control panel cutout

Panel

front face

8 ¹⁷⁄₆₄" (21.0 cm)

⁹⁄₁₆"

(6.5 cm)

¹¹⁄₃₂"

(8.7 mm)

¹⁴⁄₃₂"

(11.1 mm)

³⁄₈"

(6.0 cm)

8 ²¹⁄₃₂" (22.0 cm)

3. Remove the front panel from the screen frame.

4. Pull the control panel from the front of the trim panel.

5. Insert the control panel through the customized front panel.

6. Attach the plastic cover over the control panel and snap it

into place.

7. Press the control panel into the cutout and snap it into place.

8. Attach the customized front panel to the screen frame with

the 3 cross-recess screws.

GZ and IH Model Series

1. Use the dimensions shown to cut the front panel for either a

30" (76.2 cm) or 36" (91.4 cm) front panel, depending on size

of your vent hood.

2. Remove the 3 cross-recess screws located behind the front

trim panel in the screen frame. Remove the front panel from

the screen frame.

3. Remove the trim panel.

4. Attach the customized front panel to the screen frame with

the 3 cross-recess screws.

Accessories

Front trim kits for matching the front panel to your range or

cooktop color are available from your dealer.

NOTE: Instructions are included with each kit.

For 30" (76.2 cm) model series

Recirculation Kit:

Part No. 883140 (fits all models)

KWVU205:

Part No. 4360201 (white)

Part No. 4360203 (black)

Part No. 4392855 (biscuit)

For 36" (91.4 cm) model series

KWVU265:

Part No. 4360202 (white)

Part No. 4360204 (black)

Part No. 4392856 (biscuit)

For 30" (76.2 cm) model series

GZ7730:

Part No. 4396067 (white)

Part No. 4396066 (black)

Part No. 8171368 (biscuit)

IH530:

Part No. 4396844 (white)

For 36" (91.4 cm) model series

GZ7736:

Part No. 4396069 (white)

Part No. 4396068 (black)

Part No. 8171369 (biscuit)

A. Panel front face

A. Control panel

B. Plastic cover

Front view of control panel cutout

Panel

front face

30" (76.2 cm) model: 29 ⁷⁄₈" (75.9 cm)

36" (91.4 cm) model: 35

⁷⁄₈" (91.1 cm)

²⁵⁄₃₂"

(9.9 mm)

radius

²⁵⁄₃₂"

(18.3 mm)

¹³⁄₃₂"

(35.7 mm)

¹⁹⁄₃₂"

(15.1 mm)

⁶¹⁄₆₄"

(75.0 mm)

³¹⁄₆₄" (19.0 cm)

30" (76.2 cm) model: 29 ⁷⁄₈" (75.9 cm)

36" (91.4 cm) model: 35

⁷⁄₈" (91.1 cm)

¹⁵⁄₃₂"

(37.3 mm)

³⁄₄"

(19.1 mm)

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

KWVU Model Series

Operating the Fan

1. Slide the shelf forward.

2. Press the speed buttons for the desired speed.

Speed may be increased, decreased, or turned off at anytime

during the vent hood operation. The indicator light next to the

speed button selected should be on when the fan is running.

3. Press the 0 button or close the shelf to shut off the fan.

The fan will shut off when the shelf is about 2" (5.1 cm) from

the closed position. When the shelf is opened the fan will

operate at the last setting.

Operating the Light

1. Open the shelf about 1" (2.5 cm).

2. Press the light button.

The light will be on each time the shelf is opened. The light

can be used for a night light by opening the shelf about

1" (2.5 cm).

3. Press the light button to turn off the light.

Another option for turning off the vent hood light is to close

the shelf.

GZ and IH Model Series

Operating the Fan

1. Slide the shelf forward.

2. Move the fan switch to 1.

3. Move the speed switch to the desired setting.

The speed may be increased, decreased, or turned off at

anytime during the vent hood operation. The indicator light

should be on when the fan is running.

4. Move the fan switch to 0 or close the glass shelf.

The fan will shut off when the shelf is about 2" (5.1 cm) from

the closed position. When the shelf is opened, the fan will

operate at the last settings.

Operating the Light

1. Open the shelf about 1" (2.5 cm).

2. Move the light switch to the 1 position.

The light will be on each time the shelf is opened. The light

can be used for a night light by opening the glass shelf about

1" (2.5 cm).

3. Move the light switch to the 0 position.

Another option for turning the vent hood light off is to close

the shelf.

RANGE HOOD CARE

Cleaning

Exterior surfaces:

■ Clean the vent hood with a mild detergent and soft cloth.

■ Do not use abrasive cleansers or steel-wool pads

Metal Filter:

For the best results, clean the filters often. Pull the tabs

downward to remove filters. Place filters in dishwasher or hot,

soapy water to clean.

Replacing the Bulb

1. Use a 15-watt fluorescent bulb with 30" (76.2 cm) unit and

18-watt bulb with 36" (91.4 cm) unit.

2. Remove the screws above the light cover and set them aside.

3. Pull the light cover forward slightly and then downward to

remove the cover.

4. Replace the light bulb.

5. Lift cover back into position.

6. Replace the screws.

KWVU Model Series

GZ and IH Model Series

A. Light button

B. Speed buttons

A. Light switch

B. Fan switch

C. Indicator light

D. Speed switch

A. Screws

WIRING DIAGRAM

KWVU Model Series

LIGHT

FLAT CABLE

FAN

ON-OFF OFF

CONNECTOR

CONTROL BOARD

PUSH BUTTON PANEL

123

LIGHT

8 BS/28K–A120

WIRING BOX

BALLAST

TRANS.

FLUORESCENT

LAMP

120 VAC

LINE IN

7Fu

GZ and IH Model Series

8 BS/28K–A120

FLUORESCENT LAMP

WBK

WIRING BOX

120 VAC

LINE IN

FAN

LIGHT

BALLAST

TRANS.

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check

“Troubleshooting.” It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance.

To locate factory specified parts in your area, call us or your

nearest designated service center.

In the U.S.A.

Call the Whirlpool Customer eXperience Center

toll free: 1-800-253-1301 or call the Kitchen Aid Customer

eXperience Center toll free: 1-800-422-1230.

Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

■ Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool designated service technicians

are trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write with any questions

or concerns to:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

KitchenAid Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

For product related questions, please call the Customer

Interaction Centre toll free:

1-800-461-5681

Monday to Friday 8:00 a.m. - 6:00 p.m. (EST).

Saturday 8:30 a.m. - 4:30 p.m. (EST).

Our consultants provide assistance with:

■ Features and specifications on our full line of appliances.

■ Referrals to local dealers.

For parts, accessories and service in Canada

Call 1-800-807-6777. Whirlpool Canada LP and KitchenAid

Canada designated service technicians are trained to fulfill the

product warranty and provide after-warranty service, anywhere in

Canada.

For further assistance

If you need further assistance, you can write with any questions

or concerns to:

Customer Interaction Centre

Whirlpool Canada LP

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

KitchenAid Brand Home Appliances

KitchenAid Canada

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for FSP

replacement parts

and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

ITEMS WHIRLPOOL WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if

another warranty applies.

If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help

can be found by checking the “Assistance or Service” section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,

call 1-800-807-6777. 8/05

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name____________________________________________________

Address ________________________________________________________

Phone number__________________________________________________

Model number __________________________________________________

Serial number __________________________________________________

Purchase date __________________________________________________

KITCHENAID

VENTILATION WARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, KitchenAid or KitchenAid Canada (hereafter “KitchenAid”) will pay for factory specified parts and repair

labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.

ITEMS KITCHENAID WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by KitchenAid.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada.

6. Pickup and delivery. This major appliance is designed to be repaired in the home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service in remote locations.

9. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to determine if

another warranty applies.

If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help

can be found by checking the “Assistance or Service” section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,

call 1-800-807-6777. 9/05

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name____________________________________________________

Address ________________________________________________________

Phone number__________________________________________________

Model number __________________________________________________

Serial number __________________________________________________

Purchase date __________________________________________________

Notes

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

La page charge ...

KitchenAid 36" Installation Instructions And Use & Care Manual

Marque: KitchenAid

Modèle: 36"

Catégorie: Fours

Taper: Installation Instructions And Use & Care Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid 36"

Documents connexes

Autres documents

Whirlpool Slide-Out Range Hood Manuel utilisateur