KitchenAid KWVU Series Installation Instructions And Use & Care Manual
- Catégorie
- Fours
- Taper
- Installation Instructions And Use & Care Manual
Ce manuel convient également à
30" (76.2 CM) AND 36" (91.4 CM)
SLIDE-OUT VENT RANGE HOOD
Installation Instructions and Use & Care Guide
HOTTE D’EXTRACTION AVEC MODULE DE
COMMANDE EXTRACTIBLE 30" (76,2 CM) ET 36"
(91,4 CM)
Instructions d’installation et Guide d’utilisation et d’entretien
Table of Contents/Table des matières.............................................................................2
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.
IMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
Save installation instructions for local electrical inspector's use.
IMPORTANT :
Installateur : Remettre les instructions d'installation au propriétaire.
Propriétaire : Conserver les instructions d'installation pour référence ultérieure.
Conserver les instructions d'installation pour consultation par l'inspecteur local des installations électriques.
9763393
2
TABLE OF CONTENTS
RANGE HOOD SAFETY .................................................................3
INSTALLATION REQUIREMENTS................................................4
Tools and Parts ............................................................................4
Location Requirements................................................................4
Venting Requirements..................................................................5
Electrical Requirements ...............................................................7
INSTALLATION INSTRUCTIONS..................................................7
Prepare Location..........................................................................7
Install Range Hood ....................................................................10
Make Electrical Connection .......................................................11
Connect the Vent System. .........................................................11
Customized Front Panel.............................................................11
Accessories................................................................................12
RANGE HOOD USE......................................................................13
KWVU Model Series .................................................................13
GZ and IH Model Series.............................................................13
RANGE HOOD CARE...................................................................13
Cleaning......................................................................................13
Replacing the Bulb.....................................................................13
WIRING DIAGRAM .......................................................................14
ASSISTANCE OR SERVICE.........................................................16
In the U.S.A. ...............................................................................16
In Canada ...................................................................................16
WARRANTY ..................................................................................17
TABLE DES MATIÈRES
SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................20
EXIGENCES D’INSTALLATION...................................................22
Outillage et pièces......................................................................22
Exigences d’emplacement.........................................................22
Exigences concernant l’évacuation ...........................................23
Spécifications électriques ..........................................................25
INSTRUCTIONS D’INSTALLATION.............................................25
Préparation de l'emplacement...................................................25
Installation de la hotte de cuisinière ..........................................28
Raccordement électrique...........................................................29
Raccordement du circuit d'évacuation......................................29
Panneau avant personnalisé......................................................29
Accessoires ................................................................................30
UTILISATION DE LA HOTTE DE CUISINIÈRE...........................31
Modèles Séries KWVU ..............................................................31
Modèles Séries GZ et IH............................................................31
ENTRETIEN DE LA HOTTE DE CUISINIÈRE .............................31
Nettoyage ...................................................................................31
Remplacement de la lampe .......................................................31
SCHÉMA DE CÂBLAGE...............................................................32
ASSISTANCE OU SERVICE.........................................................33
GARANTIE.....................................................................................34
3
RANGE HOOD SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
■ Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
■ Before servicing or cleaning the unit, switch the power off at
the service panel disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service
panel.
■ Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable codes
& standards, including fire-rated construction.
■ Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
■ When cutting or drilling into wall or ceiling; do not damage
electrical wiring and other utilities.
■ Ducted systems must always be vented outdoors.
CAUTION: For general ventilating use only. Do not use
to exhaust hazardous or explosive materials and vapors.
CAUTION: To reduce risk of fire and to properly exhaust
air, be sure to duct air outside - do not vent exhaust air into
spaces within walls ceilings, attics, crawl spaces, or
garages.
WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
WARNING: TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
■ Never leave the surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
■ Always turn hood ON when cooking at high heat or when
flambeing food (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).
■ Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
■ Use proper pan size. Always use cookware appropriate for
the size of the surface element.
WARNING: TO REDUCE THE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGE TOP GREASE
FIRE, OBSERVE THE FOLLOWING:
a
■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or
other metal tray, then turn off the gas burner or electric
element. BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
■ NEVER PICK UP A FLAMING PAN - you may be burned.
■ DO NOT USE WATER, including wet dishcloths or towels -
a violent steam explosion will result.
■ Use an extinguisher ONLY if:
– You know you have a class ABC extinguisher, and you
already know how to operate it.
– The fire is small and contained in the area where it
started.
– The fire department is being called.
– You can fight the fire with your back to an exit.
a
Based on "Kitchen Fire Safety Tips" published by NFPA.
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the safety instructions provided with any tools
listed here.
Tools needed
■ Level
■ Drill
■ 1¹⁄₄" drill bit
■ ³⁄₈" (8 mm) nut driver or ratchet
■ Pencil
■ Pliers
■ Wire stripper or utility knife
■ Tape measure or ruler
■ Caulking gun and weatherproof caulking compound
■ Phillips screwdriver
■ Flat-blade screwdriver
■ Saber or keyhole saw
■ Duct tape
■ Metal snips
Parts supplied
Check that all parts are included.
■ Literature package
■ 2 screws
■ Damper
■ Plastic cover (used for customized front panel)
■ Hardware package
Parts needed
■ Two ¹⁄₂" (12.7 mm) UL listed or CSA approved conduit
connectors
■ Wall cap for interior-mounted motor
■ Metal vent system
■ Power supply cable
Optional parts needed:
■ Wood filler strips for cabinets with recessed bottoms. Length
and thickness determined by recess dimensions. See
“Prepare Location” section.
■ Two, 1" x 1" x 5" (25.4 x 25.4 x 127 mm) wood pieces for
cabinet floor. See “Prepare Location” section.
■ Four, 1¹⁄₄" (31.8 mm) wood screws
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■ Have a qualified technician install the range hood. It is the
installer’s responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating plate is located behind the left filter on the rear wall of
the vent hood.
■ Range hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.
■ Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult your
cooktop/range manufacturer installation instructions before
making any cutouts.
■ Grounded electrical outlet is required. See “Electrical
Requirements” section.
■ The hood is factory set for vented installations through the
roof or wall.
For recirculating installations, Recirculation Kit Part
Number 883140 is available from your dealer or an
authorized parts distributor.
■ All openings in ceiling and wall where range hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
5
Product Dimensions
Installation Clearances
Venting Requirements
■ Vent system must terminate to the outside.
■ Do not terminate the vent system in an attic or other enclosed
area.
■ Do not use a 4" (10.2 cm) laundry-type wall caps.
■ Use a metal vent only. A rigid metal vent is recommended. Do
not use plastic or metal foil vent.
■ The size of the vent should be uniform.
■ Use no more than three 90° elbows.
■ Make sure there is a minimum of 24" (61 cm) of straight vent
between the elbows if more than one elbow is used.
■ Do not install 2 elbows together.
■ The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
■ The vent system must have a damper. If the roof or wall cap
has a damper, do not use the damper supplied with the range
hood.
■ Use duct tape to seal all joints in the vent system.
■ Use caulking to seal exterior wall or roof opening around the
cap.
■ Determine which venting method is best for your application.
1 ⁷⁄₁₆"
2"
(5.1 cm)
Shelf extends
FRONT OF
VENT HOOD
11"
(27.9 cm)
9
¹⁄₈"
(23.2 cm)
1"
(25.4 mm)
7" (17.8 cm)
9
¹⁄₂"
(24.1 cm)
8"
1 ⁵⁄₈"
(41.3 mm)
⁵⁄₈" to 2 ¹⁄₈"
(1.6 cm to 5.4 cm)
30" (76.2 cm) model: 29 ⁷⁄₈" (75.9 cm)
36" (91.4 cm) model: 35 ⁷⁄₈" (91.1 cm)
30" (76.2 cm) model: 13" (33.0 cm)
36" (91.4 cm) model: 16" (40.6 cm)
30" (76.2 cm) model: 8" (20.3 cm)
36" (91.4 cm) model: 11" (27.9 cm)
30" (76.2 cm) model: 26" (66.0 cm)
36" (91.4 cm) model: 32" (81.3 cm)
4 ³⁄₈"
(11.1 cm)
3
¹⁄₄" (8.3 cm)
³⁄₈" (9.5 mm)
(25.4 cm)
2
³⁄₈"
(6.0 cm)
(5.1 cm)
¹⁄₄"
1 ¹⁄₄"
(31.8 mm)
10"
BACK OF
VENT HOOD
(3.6 cm)
(6.4 mm)
(20.3 cm)
2"
15" (38.1 cm)
min. clearance
upper cabinet
to countertop
13" (33 cm)
cabinet depth
30" (76.2 cm) or
36" (91.4 cm) min.
cabinet opening width
24" (61 cm) min.
30" (76.2 cm)
suggested max.
bottom of hood
to cooking surface
36" (91.4 cm)
base cabinet
height
66"(167.6 cm)
max.
to bottom of
cabinet frame
6
Venting Methods
The vent system needed for installation is not included.
A 3¹⁄₄" x 10" (8.3 cm x 25 cm) rectangular vent system is
recommended.
Calculate Vent System Length
The recommended vent system length is 3¹⁄₄" x 10" (8.3 cm x
25 cm) vent with maximum length of 26 ft (8 m) for vent system.
For the best performance, use no more than three 90° elbows.
To calculate the length of the system, add the equivalent feet
(meters) for each of the vent pieces used in the system.
Example vent system
3¹⁄₄" x 10" (8.3 cm x 25 cm)
Recommended Standard Fittings
Recirculating Vent Through the Soffit/Cabinet
This vent hood is factory set for venting through the roof or wall.
For recirculating installations, Recirculation Kit Part
Number 883140 is available from the dealer or an authorized
parts distributor. Damper installation is not required.
Roof Venting Wall Venting
A. 3¹⁄₄" x 10" (8.3 cm x 25 cm)
vent through the roof
B. Roof cap
A. 3
¹⁄₄" x 10" (8.3 cm x 25 cm)
vent through the wall
B. Wall cap
Maximum Length = 26 ft (8 m)
1 - 90° elbow = 5 ft (1.5 m)
1 - wall cap = 0 ft (0 m)
9 ft (2.8 m) straight = 9 ft (2.8 m)
System length = 14 ft (4.3 m)
A
B
A
B
90˚ elbow
3 ft
(0.93 m)
6 ft (1.8 m)
Wall cap
Vent Piece 3¹⁄₄" x 10" (8.3 cm x 25 cm)
90° elbow 5.0 ft
(1.5 m)
Flat elbow 12.0 ft
(3.7 m)
Wall cap 0.0 ft
(0.0 m)
A. 3¹⁄₄" x 10" (8.3 cm x 25 cm) vent
B. 3
¹⁄₄" x 10" (8.3 cm x 25 cm) elbow
C. Vent cover
D. Soffit
A. Hood
B. Vent system
C. Top of cabinet
D. Vent cover
E. Ceiling or soffit
A
B
C
D
A
B
C
D
E
7
Electrical Requirements
For GZ or IH model series:
WARNING: To reduce the risk of fire or electrical shock, do not
use this fan with any solid state speed control device.
For KWVU model series:
This fan is suitable for use with solid state speed controls.
IMPORTANT: Observe all governing codes and ordinances. Save
Installation Instructions for electrical inspector’s use.
It is the customer’s responsibility to contact a qualified electrical
installer, and to assure that the electrical installation is adequate
and in conformance with National Electrical Code, ANSI/NFPA 70
(latest edition), or CSA Standards C22.1-94, Canadian Electrical
Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local
codes and ordinances.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
■ A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit is
required.
■ Do not ground to a gas pipe.
■ Check with a qualified electrician if you are not sure the
downdraft vent is properly grounded.
■ Do not have a fuse in the neutral or ground circuit.
■ The range hood must be connected with copper wire only.
■ The range hood should be connected directly to the fused
disconnect (or circuit breaker) box through flexible armored or
nonmetallic sheathed copper cable.
■ Wire sizes (copper wire only) and connections must conform
with the rating of the appliance as specified on the model/
serial rating plate.
■ Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA
Standards C22. 1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition) and all local codes and
ordinances.
■ A ¹⁄₂" (12.7 mm) UL listed or CSA approved strain relief must
be provided at each end of the power supply cable (at the
range hood and at the junction box).
INSTALLATION INSTRUCTIONS
Prepare Location
It is recommended that the vent system be installed before hood
is installed.
Do not cut a joist or stud unless absolutely necessary. If a joist or
stud must be cut, then a supporting frame must be constructed.
Before making cutouts, make sure there is proper clearance
within the ceiling or wall for vent fittings.
Preparation
1. If possible, disconnect and slowly move the freestanding
range from the cabinet opening to provide easier access to
upper cabinet and rear wall.
2. Determine which venting method to use: roof, wall, or non-
vented.
3. Determine and clearly mark a centerline on the underside of
the cabinet.
4. Measure and mark lines as shown for your size of vent hood.
Use a saber saw or keyhole saw to cut an opening through
the underside of the cabinet.
The finished cutout size will be:
30” (76.2 cm) hood - 9¹³⁄₁₆" x 26¹⁄₈" (23.3 cm x 66.4 cm)
36” (91.4 cm) hood - 9¹³⁄₁₆" x 32¹⁄₈" (23.3 cm x 81.6 cm)
WARNING
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
A. Centerline
A
1
¹⁄₂"
9
³⁄₁₆"
(3.8 cm)
(23.3 cm)
30" (76.2 cm) hood - 13
¹⁄₁₆"
(33.2 cm)
36" (91.4 cm) hood - 16
¹⁄₁₆"
(40.8 cm)
8
5. If the cabinet bottom is recessed above a support frame,
wood filler strips need to be installed on the right and left
sides of the cutout to provide sides of clearance for the
sliding screen. Wood filler strips should be flush with or
recessed ¹⁄₁₆"-¹⁄₈" (1.6 mm-3.2 mm) from the bottom of the
support frame.
6. Complete cabinet preparation following the instructions for
your type of installation.
Venting Outside Through the Roof
Measure and mark the lines as shown. Use a saber saw or
keyhole saw to cut a rectangular opening for the vent.
Venting Outside Through the Wall
Assemble the vent that you will use over the vent opening. Do
not attach the vent at this time. Measure from the top of the
screen housing to the top of the vent opening (A) and back to
the bottom of the vent opening (B). Remove the vent.
Transfer measurements A and B to the cabinet back wall.
Measure from the underside of the cabinet or wood filler
strips, if used. Mark the cutout as shown. Use a saber saw or
keyhole saw to cut a rectangular opening for the vent.
Venting Inside Through the Soffit/Cabinet
Measure and mark a rectangular vent opening in the soffit
using the method shown for venting through the wall.
Measure and mark the same centerline on the soffit above the
vent hood area.
Use the grille from the Recirculation Kit or other grille as a
template to outline an opening for the vent. Use a saber saw
or keyhole saw to cut a rectangular opening for the vent
system.
The hood can be vented inside through the top of the cabinet.
The Recirculation Kit Part Number 883140 must be used.
A. Wood filler strips
A
Cutout
Centerline
(25.4 mm)
1"
(27.3 cm)
10
³⁄₄"
(10.2 cm)
4"
A
B
A. Grille
B. Centerline
A
B
Centerline
Cutout
10 ³⁄₄"
(27.3 cm)
B
A
Cutout
Centerline
(25.4 mm)
1"
(27.3 cm)
10
³⁄₄"
(10.2 cm)
4"
9
7. Install the vent system according to the method needed. Use
caulking to seal the exterior wall or roof opening.
8. Determine wiring knockout.
To wire through the top wiring knockout:
Measure and mark a 10¹⁄₈" (27 cm) line for the 30" (76.2 cm)
hood or 11⁵⁄₈" (29.5 cm) line for the 36" (91.4 cm) hood from
the right of the centerline on the cabinet ceiling. Mark a point
on this line that is 4" (10.2 cm) from the back wall of the
cabinet. Drill a 1¹⁄₄" (3.2 cm) diam. hole through the cabinet
ceiling.
To wire through the rear wiring knockout:
Measure and mark an 11³⁄₈" (29.8 cm) line for the
30" (76.2 cm) hood or 14³⁄₈" (36.5 cm) line for the
36" (91.4 cm) hood from right of the centerline on the cabinet
back wall. Mark the point on this line that is 8¹⁄₄" (21 cm) from
the bottom of the cabinet. Drill a 1¹⁄₄" (3.2 cm) diam. hole
through the wall.
9. Run the wiring through the wall or cabinet according to the
national Electrical Code and all local codes and ordinances.
Use caulking to seal around wire opening.
NOTE: Do not turn on power until installation is complete.
10.
Measure the thickness of the cabinet floor, including the filler
strips, if used. If the thickness is less than
⁵⁄₈
" (15.9 mm), install
wood filler strips that are a minimum length of 5" (12.7 cm)
onto the cabinet floor. The mounting bracket adjusts from
⁵⁄₈
" (15.9 mm) to 2
¹⁄₈
" (54 mm) for the wood filler strips
.
11. Remove the vent hood from the carton. Attach the damper to
the vent opening. If the roof cap has a damper, do not attach
the damper to the vent hood.
12. Remove the top or rear knockout from the wiring opening to
be used.
A. Wiring cutout
A. Wiring cutout
A
A
A. Damper
A. Wiring knockouts
Wood fillers
(thickness as required)
Less than ⁵⁄₈" (15.9 mm)
including bottom filler
(if used)
A
A
10
13. Place the vent hood on its back side on a protected surface.
Slide the screen forward. Pull the tabs to remove the filters.
Remove the terminal box cover. Close the screen. Slide the
mounting brackets to the top position.
NOTE: For some installations using the recirculating kit, it
may be easier to attach the vent system to the hood before
lifting the hood into its final position. Seal the connection with
duct tape.
Install Range Hood
1. Lift the vent hood into its final position and feed the electrical
wire through the wiring opening. The mounting brackets
should overlap the cabinet bottom or wood filler strips.
Center the range hood.
2. Check that the front panel is parallel with the cabinet front
when the screen is pushed in. Slide the screen forward.
Tighten the mounting bracket screws so that the vent hood is
secured to the cabinet.
3. Align the hood front panel with the cabinet. Slide the screen
forward. Locate the 2 screws on each side and turn them
counterclockwise to loosen the screws. Adjust the front of the
vent vertically, ³⁄₈" (9.5 mm) up or down, or horizontally,
³⁄₄" (19 mm) front to back, until the front is flush with the
cabinet. Tighten the screws. If it is necessary to adjust the
given dimensions, lower and add or remove the filler strips or
redrill mounting holes.
A. Terminal box cover.
A. Mounting bracket
B. Cabinet bottom
C. Optional wood filler strip
D. Vent hood
A
WARNING
Excessive Weight Hazard
Use two or more people to move and install
range hood.
Failure to do so can result in back or other injury.
A
B
C
D
A. Mounting bracket screw
B. Flat-blade screwdriver
A. Phillips screwdriver
B. Adjustment screws
A
B
A
B
11
Make Electrical Connection
1. Connect the white wire of the power supply cable to the white
wire in the hood with a twist-on connector.
2. Connect the black wire of the power supply cable to the
black wire in the hood with a twist-on connector.
3. Connect the green power supply ground wire to the green,
ground screw inside the vent hood terminal box.
4. Replace the terminal box cover.
Connect the Vent System.
1. Vented installations:
Replace the metal filter. Connect the vent system to the hood
vent opening. Seal the connection with duct tape.
Recirculation installations:
Connect the vent system to the hood vent opening. Seal the
connection with duct tape. Follow the instructions included
with Recirculation Kit Number 883140.
2. Turn the power supply on. Slide the screen forward. Check
the operation of the vent hood fan and light. Close the screen.
Customized Front Panel
The front panel of the vent hood can be removed and a
customized front panel added for a more blended look.
KWVU Model Series
It is recommended that a cabinetmaker cut the customized front
panel because of the precise cuts needed for the electronic
control panel.
1. Use the dimensions shown to cut the front panel for either a
30" (76.2 cm) or 36" (91.4 cm) front panel, depending on the
size of your vent hood.
2. Remove the 3 cross-recess screws located behind the front
trim panel in the screen frame.
A. White wires
B. Green ground screw
C. Ground wire
D. Black wires
E. Twist-on connectors
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
WARNING
Electrical Shock Hazard
Electrically ground blower.
Connect ground wire to green ground screw in
terminal box.
Failure to do so can result in death or electrical shock.
E
B
C
D
A
A. Filter
A
panel front face
Section view of control panel cutout
Panel
front face
8 ¹⁷⁄₆₄" (21.0 cm)
2
⁹⁄₁₆"
(6.5 cm)
¹¹⁄₃₂"
(8.7 mm)
¹⁴⁄₃₂"
(11.1 mm)
2
³⁄₈"
(6.0 cm)
8 ²¹⁄₃₂" (22.0 cm)
12
3. Remove the front panel from the screen frame.
4. Pull the control panel from the front of the trim panel.
5. Insert the control panel through the customized front panel.
6. Attach the plastic cover over the control panel and snap it
into place.
7. Press the control panel into the cutout and snap it into place.
8. Attach the customized front panel to the screen frame with
the 3 cross-recess screws.
GZ and IH Model Series
1. Use the dimensions shown to cut the front panel for either a
30" (76.2 cm) or 36" (91.4 cm) front panel, depending on size
of your vent hood.
2. Remove the 3 cross-recess screws located behind the front
trim panel in the screen frame. Remove the front panel from
the screen frame.
3. Remove the trim panel.
4. Attach the customized front panel to the screen frame with
the 3 cross-recess screws.
Accessories
Front trim kits for matching the front panel to your range or
cooktop color are available from your dealer.
NOTE: Instructions are included with each kit.
For 30" (76.2 cm) model series
Recirculation Kit:
Part No. 883140 (fits all models)
KWVU205:
Part No. 4360201 (white)
Part No. 4360203 (black)
Part No. 4392855 (biscuit)
For 36" (91.4 cm) model series
KWVU265:
Part No. 4360202 (white)
Part No. 4360204 (black)
Part No. 4392856 (biscuit)
For 30" (76.2 cm) model series
GZ7730:
Part No. 4396067 (white)
Part No. 4396066 (black)
Part No. 8171368 (biscuit)
IH530:
Part No. 4396844 (white)
For 36" (91.4 cm) model series
GZ7736:
Part No. 4396069 (white)
Part No. 4396068 (black)
Part No. 8171369 (biscuit)
A. Panel front face
A. Control panel
B. Plastic cover
Front view of control panel cutout
Panel
front face
30" (76.2 cm) model: 29 ⁷⁄₈" (75.9 cm)
36" (91.4 cm) model: 35
⁷⁄₈" (91.1 cm)
²⁵⁄₃₂"
(9.9 mm)
radius
²⁵⁄₃₂"
(18.3 mm)
1
¹³⁄₃₂"
(35.7 mm)
¹⁹⁄₃₂"
(15.1 mm)
2
⁶¹⁄₆₄"
(75.0 mm)
7
³¹⁄₆₄" (19.0 cm)
A
A
B
30" (76.2 cm) model: 29 ⁷⁄₈" (75.9 cm)
36" (91.4 cm) model: 35
⁷⁄₈" (91.1 cm)
1
¹⁵⁄₃₂"
(37.3 mm)
³⁄₄"
(19.1 mm)
13
RANGE HOOD USE
The range hood is designed to remove smoke, cooking vapors
and odors from the cooktop area. For best results, start the hood
before cooking and allow it to operate several minutes after the
cooking is complete to clear all smoke and odors from the
kitchen.
KWVU Model Series
Operating the Fan
1. Slide the shelf forward.
2. Press the speed buttons for the desired speed.
Speed may be increased, decreased, or turned off at anytime
during the vent hood operation. The indicator light next to the
speed button selected should be on when the fan is running.
3. Press the 0 button or close the shelf to shut off the fan.
The fan will shut off when the shelf is about 2" (5.1 cm) from
the closed position. When the shelf is opened the fan will
operate at the last setting.
Operating the Light
1. Open the shelf about 1" (2.5 cm).
2. Press the light button.
The light will be on each time the shelf is opened. The light
can be used for a night light by opening the shelf about
1" (2.5 cm).
3. Press the light button to turn off the light.
Another option for turning off the vent hood light is to close
the shelf.
GZ and IH Model Series
Operating the Fan
1. Slide the shelf forward.
2. Move the fan switch to 1.
3. Move the speed switch to the desired setting.
The speed may be increased, decreased, or turned off at
anytime during the vent hood operation. The indicator light
should be on when the fan is running.
4. Move the fan switch to 0 or close the glass shelf.
The fan will shut off when the shelf is about 2" (5.1 cm) from
the closed position. When the shelf is opened, the fan will
operate at the last settings.
Operating the Light
1. Open the shelf about 1" (2.5 cm).
2. Move the light switch to the 1 position.
The light will be on each time the shelf is opened. The light
can be used for a night light by opening the glass shelf about
1" (2.5 cm).
3. Move the light switch to the 0 position.
Another option for turning the vent hood light off is to close
the shelf.
RANGE HOOD CARE
Cleaning
Exterior surfaces:
■ Clean the vent hood with a mild detergent and soft cloth.
■ Do not use abrasive cleansers or steel-wool pads
Metal Filter:
For the best results, clean the filters often. Pull the tabs
downward to remove filters. Place filters in dishwasher or hot,
soapy water to clean.
Replacing the Bulb
1. Use a 15-watt fluorescent bulb with 30" (76.2 cm) unit and
18-watt bulb with 36" (91.4 cm) unit.
2. Remove the screws above the light cover and set them aside.
3. Pull the light cover forward slightly and then downward to
remove the cover.
4. Replace the light bulb.
5. Lift cover back into position.
6. Replace the screws.
KWVU Model Series
GZ and IH Model Series
A. Light button
B. Speed buttons
A
B
A. Light switch
B. Fan switch
C. Indicator light
D. Speed switch
B
A
C
D
A. Screws
A. Screws
A
A
14
WIRING DIAGRAM
KWVU Model Series
LIGHT
FLAT CABLE
FAN
R
R
FAN
ON-OFF OFF
CONNECTOR
CONNECTOR
V
V
V
OR
BU
BK
BK
BR
GY
W
W
CONTROL BOARD
PUSH BUTTON PANEL
123
LIGHT
K2
K1
6
8 BS/28K–A120
WIRING BOX
G
W
G
BK
BK
W
S
BALLAST
TRANS.
FLUORESCENT
LAMP
120 VAC
LINE IN
7Fu
5
H
1
4
3
2
FL
H
H
K
L
15
GZ and IH Model Series
S
8 BS/28K–A120
7
FLUORESCENT LAMP
WBK
BK
BK
BK
BK
OR
BU
GY
LP
BR
V
BK
WIRING BOX
GG
W
120 VAC
LINE IN
W
W
FAN
LIGHT
BK
RR
BALLAST
TRANS.
Fu
16
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only factory specified parts. Factory specified parts will fit
right and work right because they are made with the same
precision used to build every new appliance.
To locate factory specified parts in your area, call us or your
nearest designated service center.
In the U.S.A.
Call the Whirlpool Customer eXperience Center
toll free: 1-800-253-1301 or call the Kitchen Aid Customer
eXperience Center toll free: 1-800-422-1230.
Our consultants provide assistance with:
■ Features and specifications on our full line of appliances.
■ Installation information.
■ Use and maintenance procedures.
■ Accessory and repair parts sales.
■ Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
■ Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
For further assistance
If you need further assistance, you can write with any questions
or concerns to:
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
or
KitchenAid Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
For product related questions, please call the Customer
Interaction Centre toll free:
1-800-461-5681
Monday to Friday 8:00 a.m. - 6:00 p.m. (EST).
Saturday 8:30 a.m. - 4:30 p.m. (EST).
Our consultants provide assistance with:
■ Features and specifications on our full line of appliances.
■ Referrals to local dealers.
For parts, accessories and service in Canada
Call 1-800-807-6777. Whirlpool Canada LP and KitchenAid
Canada designated service technicians are trained to fulfill the
product warranty and provide after-warranty service, anywhere in
Canada.
For further assistance
If you need further assistance, you can write with any questions
or concerns to:
Customer Interaction Centre
Whirlpool Canada LP
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
or
KitchenAid Brand Home Appliances
KitchenAid Canada
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY
ONE YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for FSP
®
replacement parts
and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
ITEMS WHIRLPOOL WILL NOT PAY FOR
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
5. Any food loss due to refrigerator or freezer product failures.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Pickup and delivery. This major appliance is designed to be repaired in the home.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9. Expenses for travel and transportation for product service in remote locations.
10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if
another warranty applies.
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help
can be found by checking the “Assistance or Service” section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,
call 1-800-807-6777. 8/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
17
KITCHENAID
®
VENTILATION WARRANTY
ONE YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, KitchenAid or KitchenAid Canada (hereafter “KitchenAid”) will pay for factory specified parts and repair
labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.
ITEMS KITCHENAID WILL NOT PAY FOR
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by KitchenAid.
5. Replacement parts or repair labor costs for units operated outside the United States or Canada.
6. Pickup and delivery. This major appliance is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service in remote locations.
9. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to determine if
another warranty applies.
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help
can be found by checking the “Assistance or Service” section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,
call 1-800-807-6777. 9/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
18
Notes
19
20
SÉCURITÉ DE LA HOTTE DE CUISINIÈRE
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
KitchenAid KWVU Series Installation Instructions And Use & Care Manual
- Catégorie
- Fours
- Taper
- Installation Instructions And Use & Care Manual
- Ce manuel convient également à
dans d''autres langues
- English: KitchenAid KWVU Series
Documents connexes
-
KitchenAid Slide-Out Range Hood Manuel utilisateur
-
-
-
-
-
-
KitchenAid LI32NA/W10674120B Manuel utilisateur