Craftsman CMCMW220P2 Le manuel du propriétaire

Marque: Craftsman

Modèle: CMCMW220P2

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

final page size: 8.5 x 5.5 in

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1-888-331-4569 WWW.CRAFTSMAN.COM

CMCMW220

INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCTIONES

2xV20 20" Push Mower

Tondeuse Poussée 2xV20 508mm (20po)

Podadora de Empuje 2xV20 508mm (20pulg)

English (original instructions) 5

Français (traduction de la notice d’instructions originale) 15

Español (traducido de las instrucciones originales) 26

Fig. A

CMCMW220

Components

ON-OFF switch box

ON-OFF button

Safety key

Upper handle

Lower handle

Bail handle

Battery ports

Cut height adjust lever

Rear door cover

Grass collection bag

Grass collection bag handle

Lower carrying handle

Side flap

Side discharge attachment

Handle height adjust levers

Upper handle lock levers

Upper handle knob

Composants

Boîtier Marche/Arrêt

Bouton Marche/Arrêt

Clé de sûreté

Poignée supérieure

Poignée inférieure

Anse

Logements de bloc-piles

Levier de réglage de la hauteur

de coupe

Capot de la porte arrière

Sac de collecte du gazon

Poignée du sac de collecte du gazon

Poignée de transport inférieure

Volet latéral

Fixation de la décharge latérale

Leviers de réglage de la hauteur

de poignée

Leviers de verrouillage de

la poignée supérieure

Bouton de la poignée supérieure

Componentes

Caja de interruptor ON-OFF

(encendido-apagado)

Botón de encendido-apagado

Llave de seguridad

Manija superior

Manija inferior

Manija de travesaño

Puertos de batería

Palanca de ajuste de altura de corte

Cubierta de puerta trasera

Bolsa de recolección de césped

Manija de bolsa de recolección

de césped

Manija de transporte inferior

Aleta lateral

Conexión de descarga lateral

Palancas de ajuste de altura de

manija

Palancas de bloqueo de manija

superior

Perilla de manija superior

Fig.B Fig.C

Fig.D Fig.E

Fig.F

75–100% charged

Chargé de 75 à 100 %

75–100% cargada

51–74% charged

Chargé de 51 à 74 %

51–74% cargada

< 50% charged

Chargé de < 50 %

< 50% cargada

Pack needs to be charged

Le bloc-piles doit être rechargé

La batería tiene que cargarse

Indicators

Charging

Bloc-piles en Cours

de Chargement

Unidad en Proceso de Carga

Fully Charged

Bloc-piles Chargé

Unidad Cargada

Hot/Cold Pack Delay

Suspension de Charge Contre

le Chaud/Froid

Restraso por Unidad Caliente/

Fría

Fig.I Fig.J

Fig. K

Fig.G Fig.H

FRONT

BACK

Fig.N

Fig.L

Fig.M

ENGLISH

• Avoid dangerous environment – don’t use lawn mowers

in damp or wetlocations.

• Don’t Use InRain.

• Keep Children Away – All visitors should be kept a safe

distance from workarea.

• Dress Properly – Do not wear loose clothing or jewelry.

They can be caught in moving parts. Use of rubber gloves

and footwear is recommended when workingoutdoors.

• Use Safety Glasses – Always use face or dust mask if

operation isdusty.

• Use Right Appliance – Do not use lawn mower for any

job except that for which it isintended.

• Check for damaged parts. Before further use of the

mower, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect their

operation. A guard or other part that is damaged should

be properly repaired or replaced by an authorized service

center unless otherwise indicated elsewhere in thismanual.

• Repairs and service. Repairs, maintenance and

any adjustments not specified in this manual should

be performed by authorized service centers or other

qualified service organizations, always using identical

replacementparts.

• Don’t Force Lawn Mower – It will do the job better and

safer at the rate for which it wasdesigned.

• Don’t Overreach – Keep proper footing and balance at

alltimes.

• Stay Alert – Watch what you are doing. Use common

sense. Do not operate lawn mower when you aretired.

• Disconnect Lawn Mower – Remove the safety key and

battery packs from the mower when not in use, before servicing,

when changing accessories such as blades, and thelike.

• Store Idle Lawn Mower Indoors – When not in use, lawn

mower should be stored in an indoor dry and locked-up

place – out of reach of children. Remove safety key and

batterypacks.

• Maintain Lawn Mower With Care – Keep cutting edges

sharp and clean for best and safestperformance.

Follow instructions for lubricating and changing accessories.

Keep handles dry, clean, and free from oil andgrease.

• Keep guards in place and in workingorder.

• Keep bladessharp.

• Keep hands and feet away from cuttingarea.

• Objects struck by the lawn mower blade can cause severe

injuries to persons. The lawn should always be carefully

examined and cleared of all objects prior to eachmowing.

• If lawn mower strikes a foreign object, follow

thesesteps:

1. Stop lawn mower. Release the bailhandle.

2. Remove battery packs and safetykey.

3. Inspect fordamage.

4. Repair any damage before restarting and operating

the lawnmower.

IMPORTANT SAFETY WARNINGS AND

INSTRUCTIONS



WARNING: To reduce risk of injury:

• Before any use, be sure everyone using this tool

reads and understands all safety instructions and

other information contained in this manual.

• Save these instructions and review frequently prior

to use and in instructing others.



WARNING: When using battery powered lawn

mowers, basic safety precautions should always be

followed to reduce the risk of ﬁre, electric shock, and

personal injury, including thefollowing:

READ ALL INSTRUCTIONS

GENERAL SAFETY WARNINGS AND

INSTRUCTIONS FOR ALL LAWN MOWERS



DANGER:

• This tool can be dangerous. Follow all warnings

and Safety Instructions in this manual. The operator is

responsible for following warnings and instructions in

this manual and on unit. Restrict use of this mower to

persons who read, understand and follow warnings and

instructions in this manual and onunit.

Definitions: Safety Alert Symbols andWords

This instruction manual uses the following safety alert

symbols and words to alert you to hazardous situations and

your risk of personal injury or propertydamage.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.



(Used without word) Indicates a safety relatedmessage.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Intended Use

This mower is designed for residentialuse.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

English (original instructions)



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

ENGLISH

the safety key and battery packs, then check for the cause

immediately. Vibration is generally a warning of trouble.

Children Specific

1 . Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last sawthem.

2 . Keep children out of the operating area and under

the watchful care of a responsible adult other than

theoperator.

3 . Be alert and turn mower off if child enters the area.

Slope Specific

1 . Slopes are a major factor related to accidents. Operation

on slopes requires extra caution. Do not mow slope if

uncomfortable doing so.

2 . Mow across the face of slopes; never up and down.

Use caution while operating near dropoffs, ditches, or

embankments.

3 . Avoid mowing wet grass. (Poor footing could cause a slip

and fall accident.)

4 . Do not operate machine under any condition where

traction, steering, or stability is in question. Mower could

slide even if the wheels are stopped.

5 . Avoid starting and stopping on slopes. Avoid making

sudden changes in speed or direction. Make turns slowly

and gradually.

6 . Use extra care while operating machine with a grass

catcher or other attachment(s). They can affect the stability

of the machine.

Service

1 . Keep machine in good working order. Replace worn or

damaged parts.

2 . Use caution when servicing blades. Wrap the blade(s) or

wear gloves. Replace damaged blades. Do not repair or

alter blade(s). Keep all nuts and bolts tight.

3 . Keep mower free of grass, leaves, or other debris build-up.

4 . Maintain or replace safety and instruction labels as necessary.

The following are explanations of important safety

hazard pictorials on themower.

User must read and understand the

instructionmanual.

To avoid the risk of serious injury do not

mow up and down slopes. Always mow

acrossslopes.

To avoid the risk of injury to bystanders keep

all persons and pets at a safe distance from the

mower whileoperating.

• Use identical replacement bladesonly.

SAVE THESE INSTRUCTIONS

Important

Safe Practices for Pedestrian-

ControlledMowers

This machine is capable of amputating hands and feet and

throwing objects. Failure to observe the following safety

instructions could result in serious injury or death.

General Information

1 . Read, understand, and follow instructions and warnings in

this manual and on the machine, engine andattachments.

2 . Only allow operators, who are responsible, trained, familiar

with the instructions, and physically capable to operate the

machine.

3 . Do not operate the machine while under the influence of

alcohol or drugs.

Preparation Before Operating

1 . Clear the operating area of any objects which could be

thrown by or interfere with operation of the machine.

2 . Keep the area of operation clear of all bystanders,

particularly small children and pets. Stop the machine and

attachment(s) if anyone enters the area.

3 . Do not operate the machine without the entire grass

catcher, discharge chute, or other safety devices in place

and functioning properly. Check frequently for signs of wear

or deterioration and replace as needed.

4 . Wear appropriate personal protective equipment such as

safety glasses, hearing protection, respiratory protection

and footwear.

Operating

1 . Only operate the machine in daylight or good

artificiallight.

2 . Avoid holes, ruts, bumps, rocks, or other hidden hazards.

Uneven terrain could overturn the machine, or cause

operator's loss of balance or footing. Tall grass can hide

obstacles. Stay behind handle.

3 . Do not put hands or feet near rotating parts or under the

machine. Keep clear of the discharge opening at all times.

4 . Do not direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction. Material

may ricochet back toward the operator. Stop the blade(s)

when crossing gravel surfaces.

5 . Do not pull mower backward unless absolutely

necessary. Always look down and behind before and

while moving backward.

6 . Always release the bail handle to stop the motor and wait until

the blade comes to a complete stop and remove the safety

key and battery packs before cleaning the mower, removing

the grass catcher, unclogging the discharge, when leaving

the mower, when storing the mower, when transporting the

mower, or before any adjustments, repairs or inspection.

7 . If the mower should start to vibrate abnormally, release

the bail handle, wait for the blade to stop and remove

ENGLISH

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into a

non‑compatible charger as battery pack may rupture

causing serious personal injury. Consult the chart

at the end of this manual for compatibility of batteries

andchargers.

• Charge the battery packs only in

CRAFTSMANchargers.

• DO NOT splash or immerse in water or otherliquids.

• DO NOT allow water or any liquid to enter batterypack.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack

can explode in a fire. Toxic fumes and materials are created

when lithium-ion battery packs areburned.

• Do not expose a battery pack or appliance to ﬁre or

excessive temperature. Exposure to ﬁre or temperature

above 265°F (130°C) may causeexplosion.

• Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature

range speciﬁed in the instructions. Charging improperly

or at temperatures outside of the speciﬁed range may

damage the battery and increase the risk ofﬁre.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

..................... wear hearing

protection

..................... read all

documentation

..................... avoid staring at

light

or AC............alternating current

Ah ....................... amp hours

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

BPM .................... beats per minute

V ......................... volts

min ..................... minutes

or DC ............direct current

…/min ..............per minute

RPM .................... revolutions per

minute

A ......................... amperes

Hz .......................hertz

W ........................watts

Wh ......................watt hours

.......................no load speed

n .........................rated speed

.....................safety alert symbol

..................... wear respiratory

protection

..................... wear eye protection

..................... Class II Construction

(double insulated)

Rotating blades can cause serious injury.

Keep hands and feet clear of mower deck and

discharge opening at all times. Always be

sure blade has stopped. Release bail handle

to turn mower off and wait for the blade

to stop rotating (approximately 3 seconds)

and remove the safety key and battey packs

before removing and replacing grass catcher,

cleaning, servicing, transporting or lifting

themower.

Objects struck by mower blade can cause

serious injury. Stay behind the handle when the

motor is running. Always ensure persons and

pets are clear of the discharge from the mower

while operating. Always inspect mowing area

before mowing and remove objects that could

be thrown by blade. Release bail handle to

turn mower off and wait for the blade to stop

rotating (approximately 3 seconds) before

crossing walk, roads, patio and graveldrives.

Additional Safety Information



WARNING: Never modify the power tool or any part of

it. Damage or personal injury couldresult.



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. Wear hearing

protection if cutting operation is noisy. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by this product

contains chemicals known to the State of California to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides

andpesticides

• arsenic and chromium from chemically

treatedlumber

To reduce your exposure to these chemicals, wear approved

safety equipment such as dust masks that are specially designed

to filter out microscopicparticles.

ENGLISH

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than a CRAFTSMAN charger.

CRAFTSMAN chargers and battery packs are specifically

designed to worktogether.

• These chargers are not intended for any uses other

than charging CRAFTSMAN rechargeable battery

packs. Charging other types of battery packs may cause

them to overheat and burst, resulting in personal injury,

property damage, fire, electric shock orelectrocution.

• Do not expose the charger to rain orsnow.

• Do not allow water or any liquid to entercharger.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the heavier the cord and

thus the greater its capacity. An undersized cord will

cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size

to use depending on total length of all extension cords

plugged together, and nameplate ampere rating. If in

doubt, use the next heaviergauge.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

Ampere Rating

American Wire Gauge

More Than Not More

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source.

RBRC®Seal.

RBRC® is a registered trademark of Call 2Recycle,Inc.

The RBRC® Seal

Please take your spent battery packs to

an authorized service center or to your

local retailer for recycling. In some areas,

it is illegal to place spent battery packs in

the trash. You may also contact your local recycling center

for information on where to drop off the spent battery pack.

Do not place in curbside recycling. For more information

visit www.call2recycle.org. or call the toll free number in the

eye for 15minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of a

mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.

• Battery liquid may be flammable if exposed to spark

orflame.

• Never attempt to open the battery pack for any

reason. If the battery pack case is cracked or

damaged, do not insert into the charger. Do not crush,

drop or damage the battery pack. Do not use a battery pack

or charger that has received a sharp blow, been dropped,

run over or damaged in any way (e.g., pierced with a nail,

hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center forrecycling.

Storage Recommendations

The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold. Store the fully

charged battery pack out of thecharger.

Battery Pack Cleaning Instructions

Dirt and grease may be removed from the exterior of the

battery pack using a cloth or soft non-metallic brush. Do not

use water or any cleaningsolutions.

Fuel Gauge Battery Packs (Fig.B)

Some battery packs include a fuel gauge. When the

fuel gauge button is pressed and held, the LED lights

will indicate the approximate level of charge remaining.

This does not indicate tool functionality and is subject to

variation based on product components, temperature, and

end-userapplication.

Transportation



WARNING: Fire hazard. Do not store, carry, or

transport the battery pack so that metal objects

can contact exposed battery terminals. For

example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc.,

with loose nails, screws, keys, coins, hand tools, etc.

When transporting individual battery packs, make

sure that the battery terminals are protected and well

insulated from materials that could contact them and

cause a short circuit. NOTE: Li-ion battery packs should

not be put in checked baggage on airplanes and must

be properly protected from short circuits if they are in

carry-onbaggage.

ENGLISH

ASSEMBLY AND ADJUSTMENTS



DANGER: To reduce the risk of serious personal

injury, turn unit off and remove the safety key and

battery packs before making any adjustments or

removing/installing attachments or accessories.

An accidental start-up can causeinjury.

Wall Mounting

Some CRAFTSMAN chargers are designed to be wall

mountable or to sit upright on a table or work surface. If wall

mounting, locate the charger within reach of an electrical

outlet, and away from a corner or other obstructions which

may impede air flow. Use the back of the charger as a

template for the location of the mounting screws on the wall.

Mount the charger securely using drywall screws (purchased

separately) at least 1” (25.4mm) long, with a screw head

diameter of 0.28–0.35” (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32” (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

VersaTrack™



WARNING: Do not charge batteries while charger is

hung onTrackwall.

CRAFTSMAN chargers can be stored on CRAFTSMAN

VersaTrack™ Trackwall. Hooks and accessories are sold

separately. Please refer to the VersaTrack™ Trackwall accessory

sheet for furtherinformation.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

Important Charging Notes

1. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

2. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out

the lights;

c. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

3. You may charge a partially used pack whenever you

desire with no adverse effect on the batterypack.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaningsolutions.

The charger is ventilated through slots in the top and the

bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug. Have them replacedimmediately.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

• Foreign materials of a conductive nature, such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil or any buildup of metallic particles

should be kept away from the charger cavities and

ventilation slots.

• Always unplug the charger from the power supply

when there is no battery pack in thecavity.

Charging a Battery (Fig.C)

1. Plug the charger into an appropriate outlet.

2. Insert and fully seat battery pack. Green charging light

will continuously blink whilecharging.

3. Charging is complete when the green charging light

remains continuously ON. Battery pack can be left in

charger or removed.



WARNING: Only charge batteries in air temperature

over 40° F (4.5° C) and below 105° F (+40.5° C).

4. Charger will not charge a faulty battery pack, which

may be indicated by the light staying OFF. Take charger

and battery pack to an authorized service center if light

staysOFF.

NOTE: Refer to label near charging light on charger for

blinkpatterns.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack may charge at a slower rate than a warm

batterypack.

The hot/cold pack delay will be indicated by the green light

continuing to blink but with the red light continuously

ON. Once the battery pack has reached an appropriate

temperature, the red light will turn OFF and the charger will

resume the chargingprocedure.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deep discharge. The tool will automatically

turn off and the battery pack will need to berecharged.

ENGLISH

READ THIS INSTRUCTION MANUAL BEFORE

OPERATING YOUR MOWER

Refer to Figure A at the beginning of this manual for a complete

list ofcomponents. Save this manual for futurereference.



DANGER: Sharp moving blade. Do not operate the

mower in mulching mode if the rear door and side

discharge door are not closed under spring tension

as serious injury could result. Take your mower to the

nearest service center forrepair.

Proper hand position requires both hands grasping the main

handle

14

, and bail handle

13

Proper Hand Position (Fig. L)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery packs

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Adjusting Mower Height (Fig. H)

The height of cut is adjusted by the cut height adjustlever

8

NOTE: If you are not sure what height to cut at, begin

mowing with the cut height adjustment levers

8

positioned

towards the rear of the appliance and adjust the height down

asneeded.

To Set the Height of Cut

1. Pull the cut height adjustment lever

8

out of the locking

notch

20

2. Move the lever towards the rear of the appliance to raise

the height ofcut asdesired.

3. Move the lever towards the front of the appliance to

lower the height ofcut asdesired.

4. Push the cut height adjustment lever

8

into one of the

lockingnotches

20

to set theheight.

5. Repeat for the other cut height adjustment lever

8

Mulching (Fig. A, F, G)



DANGER: Turn unit off and remove safety key and

battery packs.

1. To operate mower in mulching mode, remove the grass

collection bag

10

2. Be sure rear door cover

9

isclosed.

3. If installed, remove side discharge chute

14

and make

sure side flap

13

is fully down.

4. Release the side flap and ensure the side discharge

chute

14

holds in place before turning moweron.

NOTE: The

rear door cover

9

is shaped in such a way

that the opening (at the bottom) cannot be completely

closedoff.

Side Discharge (Fig. A, G)



DANGER: Turn unit off and remove safety key and

battery packs.

1. To operate mower in side discharge mode, remove the

grass collection bag

10

2. Be sure rear door cover

9

isclosed.

3. Lift the side flap

13

and hook side discharge chute

14

onto themower.

Grass Collection Bag (Fig. F)



DANGER: Turn unit off and remove safety key and

battery packs.

1. Lift the rear door cover

9

and place the grass collection

bag

10

onto the mower so the bag hooks

18

rest

on the lugs

19

as shown in Fig. F. Then lower the rear

doorcover.

2. If installed, remove side discharge chute

14

and make

sure side flap

13

is fully down.

Attaching Upper Handle (Fig.A, E)

1. Line up the holes on the bottom of the upper handle

4

with the holes on the top of the lower handle

5

. Take

care to not pinch or stress the cord.

NOTE: Make sure the cord is located on the front of both

handles. If it is not it may result in the cord tangling and the

inability to easily store themower.

2. From the outside of the upper handle

4

, slide the handle

lock levers

16

through the two handle holes. Repeat for

the oppositeside.

3. From the inside of the upper handle loosely tighten a

knob

17

onto each handle lock lever

20

4. Rotate the upper handle

4

into its operatingposition.

Take care to not pinch or stress the cord.

5. Close the handle lock levers

16

securing the upper

handle intoposition.

NOTE: If the connection between the handle and lever

is too tight or too loose, open the lever and adjust the

depth of the lever by turning the lever clockwise or

counterclockwise.

Close it again until each lever stays

securelyclosed and the handle is secure and will not move.

Adjusting Handle Height (Fig. A, D)

The mower is shipped in storage mode. You will need to

adjust the handle to operating position beforecontinuing.

1. To unlock the lower handle

from the storage position,

open the two handle height adjust levers

15

. The handle

height adjust levers

15

are located on both sides of the

lower handle

5

2. Raise the lower handle to the operatingposition. Take

care to not pinch or stress the cord.

3. Close the handle height adjust levers

15

, securing the

lower handle intoposition.

NOTE:

If the connection between the handle and lever

is too tight or too loose, open the lever and adjust the

depth of the lever by turning the lever clockwise or

counterclockwise. Close it again until each lever stays

securelyclosed and the handle is secure and will not move.

ENGLISH

Mowing Tips (Fig. A)



WARNING: ALWAYS INSPECT AREA WHERE

MOWER IS TO BE USED AND REMOVE ALL STONES,

STICKS, WIRE, BONES, AND OTHER DEBRIS WHICH

MIGHT BE THROWN BY THE ROTATINGBLADE.



WARNING: Mow across the face of slopes, never

up-and-down. Exercise extreme caution when

changing direction on slopes. Do not mow excessively

steep slopes. Always maintain goodfooting.

• Release bail handle to turn mower “OFF” when crossing

any gravel area (stones can be thrown by theblade).

• Set mower at highest cutting height when mowing in rough

ground or in tall weeds. Removing too much grass at one

time can cause the motor to be overloaded and to stop.

• If a grass collection bag

10

is used during the fast

growing season, the grass may tend to clog up at the

discharge opening. Release bail handle to turn mower

off, remove the safety key and battery packs. Remove

the catcher and shake the grass down to the back end

of the bag. Also clean out any grass or debris which may

be packed around the discharge opening. Replace the

grasscatcher.

• If mower should start to vibrate abnormally, release bail

handle to turn mower off, remove the safety key and

battery packs. Check immediately for cause. Vibration is a

Mower Overload

To prevent damage due to overload conditions, do not try to

remove too much grass at one time. Slow down your cutting

pace, or raise the cutheight.

1. Lift and hold the battery port cover

9

up to expose the

battery port

20

2. Slide a battery pack

21

into the battery port

24

until an

audible click is heard. Repeat this process for the second

batteryport.

NOTE: Ensure the battery packs are fully seated and fully

latched intoposition before startingmower.

3. Close the battery port cover. Ensure the cover is fully

closed before startingmower.

4. Insert safety key

3

into the ONOFF switch box

1

until it is fully seated inside housing. The mower is

nowoperational.

5. Your mower is equipped with a special ONOFF switch

box

1

. To operate the mower, push and hold the

ONOFF button

2

on the ONOFF switch box

1

, then

pull the bail handle

6

to the handlebar

34

NOTE: Once the mower starts you can release

theONOFFbutton, but you must continue to hold the

bail handle to thehandlebar for the mower to run.

6. To turn the mower OFF, release the bailhandle

6



WARNING: Never attempt to lock a switch or bail

handle in the ONposition.

NOTE: Once the bail handle has returned to the original

position it will activate the “Automatic Braking Mechanism”.

The motor is braked and the mower blade will stop rotating

in three seconds orless. If mower blade rotates longer than

three seconds, discontinue using mower and have it serviced.

Starting Mower (Fig. I–K)



DANGER: Sharp moving blade. Never attempt

to override the operation of the switch box and

safety key system as serious injury couldresult.

NOTE: Mower is operational when battery packs and safety

key areinstalled.

Safety Key (Fig. J)



DANGER: Sharp moving blade. In order to prevent

accidental start-up or unauthorized use of your

cordless mower, a removable safety key

3

has been

incorporated into the design of your mower. The mower

will be completely disabled when the safety key has

been removed from themower.

NOTE: The safety key has a tether rope to allow for storage

on a nail, out of the reach of children. Do not tether safety

key tomower.



DANGER: Rotating blades can cause serious

injury. To prevent serious injury, turn unit off and

remove safety key and battery packs when unattended,

or when charging, cleaning, servicing, transporting,

lifting, or storingmower.

Installing and Removing the Battery Packs

(Fig. I)



DANGER: MAKE CERTAIN THE SAFETY KEY IS

REMOVED TO PREVENT ACTUATION BEFORE

REMOVING OR INSTALLINGBATTERIES.



WARNING: Use only CRAFTSMAN 20V batteries.

This mower is designed to operate on two battery packs

of equal capacity. The mower will not operate on a single

battery pack, and If using different capacity battery packs, the

smaller capacity battery pack, when depleted, will cause the

unit to turn off

NOTE: For best results, make sure the battery packs are

fullycharged.

To Install the Battery Packs

1. Slide a battery pack

21

into the battery port

24

until

an audible click is heard (Fig. I). Repeat for the second

batteryport.

NOTE: Ensure the battery packs are fully seated and fully

latched intoposition before startingmower.

To Remove the Battery Packs

1. Depress the battery release button

23

on the battery

pack

21

and pull the battery packs

21

out oftool.



DANGER: Do not operate mower unless handle is

locked intoposition.



DANGER:

Sharp moving blade. Never operate the

mower in bagging mode unless the bag hooks on the

grass collection bag are seated properly on the mower

and the rear discharge door rests firmly against the top of

the grass collection bag as serious injury couldresult.



WARNING: Let the mower work at its own pace. Do

notoverload.

ENGLISH

Blade Sharpening

KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A

DULL BLADE DOES NOT CUT GRASSCLEANLY.



WARNING: Use gloves and proper eye protection while

removing, sharpening, and installing blade. Ensure that

safety key and battery pack are removed.

Sharpening the blade twice during a mowing season is

usually sufficient under normal circumstances. Sand causes

the blade to dull quickly. If your lawn has sandy soil, more

frequent sharpening may berequired. REPLACE BENT OR

DAMAGED BLADEIMMEDIATELY.

When Sharpening the Blade:

• Make sure blade remainsbalanced.

• Sharpen blade at the original cuttingangle.

• Sharpen cutting edges on both ends of blade, removing

equal amounts of material from bothends.

To Sharpen Blade in a Vise (Fig. M)

1. Be sure the bail handle is released, the blade has stopped

and safety key and battery pack are removed before

removing theblade.



DANGER: To reduce the risk of serious personal

injury, turn unit off, remove safety key and

battery packs before making any adjustments or

removing/installing attachments or accessories.

An accidental start-up can causeinjury.

1. Cut a piece of 2" x 4" wood

24

(about 2 feet long)

(610mm) to keep blade from turning when removing

the flange nut 

25



WARNING: Use gloves and proper eye protection.

Turn the mower on its side. Be careful of sharp edges

of blade.

2. Position wood and unscrew flange nut counterclockwise

with a 18mm wrench

26

as shownin Fig.L.

3. Remove square metal blade spacer 

27

, square plastic

blade insulator 

28

and blade 

29

as shown in Fig. L. The

blade support

30

should not be removed. Examine all

pieces for damage and replace ifnecessary.

4. Install sharpened or new bladeon shoulder of the blade

fan as shown in Fig.L

NOTE: When replacing sharpened or new blade on

shoulderof blade fan, make sure the “GRASS SIDE” on the

blade will be facing the ground when the mower is returned

to its normal uprightposition.

5. Install the plastic blade insulator

28

on the blade such

that the raised lips on one side engage the edges of

theblade.

6. Install the blade spacer

27

so that it sits inside the raised

lips on the other side of the blade insulator. Be sure to

align the flats in the hole of the blade spacer with the

flats of the shaft, rotating the blade and blade insulator

together as necessary.

7. Position piece of wood to keep blade from turning as

shown in Fig. L. Install flange nut

25

with the flange

against the blade spacer

27

and securely tighten the

blade

29

with a 18mm wrench

26

Removing and Installing Blade (Fig. L)



DANGER: RISK OF INJURY. WHEN REASSEMBLING

THE BLADE SYSTEM, ENSURE EACH PART IS

REINSTALLED CORRECTLY, AS DESCRIBED BELOW.

IMPROPER ASSEMBLY OF THE BLADE OR OTHER PARTS

OF THE BLADE SYSTEM MAY CAUSE SERIOUSINJURY.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the safety

key and battery pack battery packs before

making any adjustments or removing/installing

attachments or accessories. An accidental start-up

can causeinjury.

Storage (Fig. D, E)



DANGER: Rotating blade can cause serious

injury. Release bail handle to turn mower off, remove

safety key, and remove battery packs before lifting,

transporting, or storing the mower. Store in a dryplace.



CAUTION: Pinch point. To avoid being pinched, keep

fingers away from area around handle brackets when

folding downhandles.

The handle of the mower can be easily folded down for quick

and convenientstorage.

1. Open the handle lock levers

16

securing the

upperhandle.

2. Rotate the upper handle towards the front of themower.

3. Open the handle height adjust levers

15

4. Rotate

the lower handle to the storageposition.

5. Close the handle height adjust levers

15

, securing the

lower handle into the storageposition.

warning of trouble. Do not operate mower until a service

check has been made.

• For best cutting results, keep blade sharpened

andbalanced.

• Inspect and thoroughly clean mower after each use as a

deck with caked grass will degradeperformance.

• Always release bail handle to turn mower off, remove

safety key and battery packs when leaving it unattended

even for a short period oftime.

The following suggestions will help you

to obtain optimum run time from your

cordless mower:

• Slow down in areas where the grass is especially long

orthick.

• Avoid mowing when the grass is wet from rain or

dew-soaked.

• Cut your lawn frequently, especially during high

growthperiods.

NOTE: It is recommended that your battery packs be

recharged after use to prolong the battery pack life. Frequent

charging will not harm your battery pack, and will ensure that

the battery pack is fully charged and ready for its next use.

Storing battery pack not fully charged will shorten itslife.

ENGLISH

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

• Register online at www.craftsman.com/registration

Repairs

The charger and battery pack are notserviceable. There are

no serviceable parts inside the charger or batterypack.



WARNING: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment (including brush

inspection and replacement, when applicable) should

be performed by a CRAFTSMAN factory service center

or a CRAFTSMAN authorized service center. Always use

identical replacementparts.

Accessories



WARNING: Since accessories, other than those

offered by CRAFTSMAN, have not been tested with

this product, use of such accessories with this tool

could be hazardous. To reduce the risk of injury, only

CRAFTSMAN recommended accessories should be used

with thisproduct.

Recommended accessories for use with your tool are available

at extra cost from your local dealer or authorized service

center. If you need assistance in locating any accessory, please

contact CRAFTSMAN call 1-888-331-4569 .

Meets CPSC Safety Requirements

CRAFTSMAN Mowers conform to the safety standards of

the American National Standards Institute, and the U.S.

Consumer Product Safety Commission. The blade turns when

the blade motor isrunning.

Corrosion (Fig. A)

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. If you mow in areas

where fertilizers or chemicals have been used, the mower

should be cleaned immediately afterward as follows:

Release bail handle

6

to turn mower off and remove battery

and safety key. Wipe all exposed parts with a dampcloth.



CAUTION: Do not pour or spray water on the mower

in an attempt to clean it. Do not store the tool on or

adjacent to fertilizers or chemicals. Such storage can

cause rapidcorrosion.

Cleaning (Fig. A)



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always use ANSI Z87.1 (CAN/CSA Z94.3)

approved eye protection and NIOSH/OSHA/MSHA

approved respiratory protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of the

tool. These chemicals may weaken the plastic materials

used in these parts. Use a cloth dampened only with

water and mild soap. Never let any liquid get inside the

tool; never immerse any part of the tool into aliquid.

Release bail handle

6

to turn mower off, let the blade come

to a stop and then remove battery and safety key. Clean out

any clippings which may have accumulated on the underside

of the deck. After several uses, check all exposed fasteners

fortightness.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have

plastic bearing surfaces which require nolubrication.

Blade Balancing (Fig. N)

Check balance of the blade

29

by placing center hole in

the blade over a nail or round screwdriver

32

, clamped

horizontally in a vise

31

. If either end of the blade rotates

downward, file along the sharp edge of that dropping end.

Blade is properly balanced when neither enddrops.

2. Remove blade from mower. See instructions for

Removing and InstallingBlade.

3. Secure blade

29

in a vise

31

4. Wear proper eye protection and gloves and be careful

not to cutyourself.

5. Carefully file the cutting edges of the blade with a fine

tooth file

33

or sharpening stone, maintaining the angle

of the original cuttingedge.

6. Check balance of blade. See instructions for

BladeBalancing.

7. Replace blade on mower and tightensecurely.

ENGLISH

Three Year Limited Warranty

CRAFTSMAN will repair or replace, without charge, any

defects due to faulty materials or workmanship for three

years from the date of purchase (two years for batteries).

This warranty does not cover part failure due to normal wear

or tool abuse. For further detail of warranty coverage and

warranty repair information, visit www.craftsman.com

or call 1-888-331-4569. This warranty does not apply to

accessories or damage caused where repairs have been

made or attempted by others. THIS LIMITED WARRANTY

IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

2 YEARS FREE SERVICE ON CRAFTSMAN

BATTERYPACKS

CMCB201, CMCB2011, CMCB2015

3 YEARS FREE SERVICE ON CRAFTSMAN

BATTERYPACKS

CMCB202, CMCB204, CMCB205, CMCB206

NOTE: Battery warranty voided if the battery pack is

tampered with in any way. CRAFTSMAN is not responsible for

any injury caused by tampering and may prosecute warranty

fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your CRAFTSMAN Power Tool or Nailer for any reason, you

can return it within 90 days from the date of purchase with a

receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-888-331-4569

for a freereplacement.

FRANÇAIS

Français (traduction de la notice d’instructions originale)



AVERTISSEMENT : lire tous les avertissements

de sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

LISEZ TOUTES LES INSTRUCTIONS

INSTRUCTIONS ET AVERTISSEMENTS DE

SÉCURITÉ GÉNÉRAUX POUR TOUTES LES

TONDEUSES À GAZON



DANGER:

• Cet outil peut être dangereux. Suivez tous les

avertissements et toutes les instructions de sécurité dans

ce manuel. L’utilisateur est responsable de suivre les

avertissements et instructions de ce manuel et sur l’appareil.

Limitez l’utilisation de cette tondeuse aux personnes qui

lisent, comprennent et suivent les avertissements et les

instructions de ce manuel et sur l’appareil.

• Évitez les environnements dangereux. Ne pas utiliser

des tondeuses dans des endroits humides ou mouillés.

• Ne pas utiliser sous la pluie.

• Gardez les enfants éloignés. Tous les visiteurs devraient

être gardés à une distance sécuritaire de l'aire de travail.

• Portez des vêtements appropriés. Ne pas porter des

vêtements amples ou des bijoux. Ils peuvent se coincer

dans les pièces qui se déplacent. L’utilisation de gants en

caoutchouc et de chaussures est recommandée lors du

travail extérieur.

• Utilisez des lunettes de sécurité. Utilisez un masque

facial ou antipoussières s’il y a de la poussière durant

l’utilisation.

• Utilisez le bon outil.Ne pas utiliser la tondeuse à gazon

pour toute tâche autre que celles pour lesquelles elle est

conçue.

• Faire un contrôle pour détecter toute pièce

endommagée. Avant toute utilisation ultérieure de

la tondeuse, un protecteur ou une autre pièce qui est

endommagé doit être soigneusement vérifié afin de

déterminer s’il fonctionnera correctement et s’il effectuera

la fonction prévue. Vérifiez l’alignement des pièces qui se

déplacent, les fixations des pièces qui se déplacent, le bris

des pièces, le montage et tout autre état qui peut affecter

leur utilisation. Un protecteur ou une autre pièce qui est

endommagé doit être convenablement réparé ou remplacé

par un centre de services autorisé sauf indication contraire

dans ce manuel.

• Réparations et service. Les réparations, l’entretien et

les ajustements non énumérés dans ce guide doivent être

effectués dans des centres de services autorisés ou des

entreprises de service qualifiées, toujours en utilisant des

pièces de remplacement identiques.

• Ne pas forcer la tondeuse. Elle travaillera mieux et sera

plus sécuritaire à la vitesse pour laquelle elle a été conçue.

• Ne pas s’étirer. Maintenez vos pieds bien d'aplomb sur le

sol et un bon équilibre en tout temps.

• Demeurez vigilant. Regardez ce que vous faites. Faites

preuve de bon sens. Ne pas utiliser la tondeuse lorsque vous

êtes fatigué.

• Débrancher la tondeuse à gazon – Retirez la clé de sûreté et

les blocs-piles de la tondeuse lorsqu’elle n’est pas utilisée, avant

AVERTISSEMENTS DE SÉCURITÉ

IMPORTANTS ET INSTRUCTIONS



AVERTISSEMENT: Afin de réduire le risque de blessure:

• Avant toute utilisation, assurez-vous que toutes

les personnes qui utiliseront cet outil lisent et

comprennent toutes les consignes de sécurité et

les autres renseignements compris dans le présent

manuel.

• Conservez ces instructions et passez-les en revue

fréquemment avant l’utilisation et la formation

d'autres personnes.



AVERTISSEMENT: Lors de l'utilisation de tondeuses à

gazon alimentées par piles, les mesures de précaution

de base devraient toujours être prises pour réduire le

risque d'incendie, de choc électrique et de blessures,

incluant ce qui suit:

Définitions: symboles et termes

d'alarmessécurité

Ces guides d'utilisation utilisent les symboles et termes

d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels

oumatériels.



DANGER : indique une situation dangereuse

imminente qui, si elle n’est pas évitée, entraînera la

mort ou des blessuresgraves.



AVERTISSEMENT : indique une situation

potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner la mort ou des blessuresgraves.



ATTENTION : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait

entraîner des blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message

propre à lasécurité.

AVIS : indique une pratique ne posant aucun risque

de dommages corporels mais qui par contre, si rien

n’est fait pour l’éviter, pourrait poser des risques de

dommagesmatériels.

Utilisation prévue

Cette tondeuse poussée est conçue pour utilisation résidentiel

NE PAS utiliser en conditions mouillées ou en présence de

liquides ou de gaz inflammables.

NE PAS laisser les enfants entrer en contact avec l’outil.

Une supervision est requise lorsque des utilisateurs non

expérimentés utilisent cet outil.

FRANÇAIS

compagnie. Arrêtez la machine et les accessoires si

quelqu’un entre dans la zone.

3 . Ne pas faire fonctionner la machine sans tout le sac

à herbe, le conduit d’éjection ou autres dispositifs de

sécurité en place et fonctionnant correctement. Vérifiez

régulièrement les signes d’usure ou de détérioration et

remplacer s’il y a lieu.

4 . Portez un équipement de protection individuel approprié

comme des lunettes de sécurité, une protection auditive,

une protection respiratoire et des chaussures.

Utilisation

1 . Utilisez seulement la machine en plein jour ou avec une

bonne lumière artificielle.

2 . Évitez les trous, les ornières, les bosses, les roches ou d’autres

dangers cachés. Un terrain inégal peut faire renverser

la machine ou faire perdre l’équilibre ou son aplomb à

l’utilisateur. L’herbe haute peut cacher des obstacles. Restez

derrière la poignée.

3 . Ne pas mettre les mains ou les pieds près des pièces en

rotation ou sous la machine. Tenez-vous éloigné de

l’ouverture d'éjection en tout temps.

4 . Ne pas diriger la matière rejetée vers quiconque. Évitez de

rejeter la matière contre un mur ou une obstruction. La

matière peut ricocher vers l’utilisateur. Arrêtez les lames

lorsque vous traversez des surfaces en gravier.

5 . Ne pas tirer la tondeuse vers l’arrière à moins que ce ne

soit absolument nécessaire. Regardez toujours vers le bas

et derrière avant de vous déplacer vers l'arrière.

6 . Relâchez l’anse pour arrêter le moteur et attendez jusqu’à ce

que la lame s’arrête complètement et retirez la clé de sûreté et

les blocs-piles avant de nettoyer la tondeuse, de retirer le sac

de collecte de l’herbe, de désobstruer la protection d’éjection,

lorsque vous laissez la tondeuse, que vous l’entreposez, la

transportez ou avant d’effectuer tout ajustement, toute

réparation ou toute inspection.

7 . Si la tondeuse devait démarrer en vibrant de façon

anormale, relâchez l’anse, attendez que la lame s’arrête

et retirez la clé de sûreté et les blocs-piles, puis vérifiez

immédiatement la cause. La vibration est généralement un

avertissement de problème.

Concernant les enfants

1 . Des accidents tragiques peuvent se produire si l’utilisateur

ne fait pas attention à la présence des enfants. Les enfants

sont souvent attirés par la machine et l’activité de tonte. Ne

jamais présumer que les enfants demeureront à l’endroit où

vous les avez vus la dernière fois.

2 . Gardez les enfants hors de la zone d’utilisation et sous la

vigilance d’un adulte responsable autre que l’utilisateur.

3 . Soyez attentif et éteignez la tondeuse si un enfant entre

dans la zone.

Concernant les pentes

1 . Les pentes sont un facteur important lié aux accidents.

L’utilisation sur les pentes nécessite une prudence accrue.

Ne tondez pas en pente si cette opération est inconfortable.

l’entretien, pour changer des accessoires comme les lames et

autres.

• Entreposez la tondeuse à gazon arrêtée à l’intérieur

‑ Lorsqu’elle n’est pas utilisée, la tondeuse à gazon doit être

entreposée à l’intérieur dans un endroit sec et verrouillé

hors de portée des enfants. Retirez la clé de sûreté et les

blocs-piles.

• Entretenez soigneusement la tondeuse à gazon.

Gardez bords coupants aiguisés et propre pour la meilleure

performance et la plus sécuritaire.

Pour lubrifier l'outil et remplacer les accessoires, suivez les

directives du manuel. Gardez vos mains sèches, propres et

exemptes de graisse et de poussière.

• Maintenez les protecteurs en place en bon état de

fonctionnement.

• Gardez les lames aiguisées.

• Gardez vos mains et vos pieds à distance de la zone

de coupe.

• Les objets frappés par la lame de la tondeuse à gazon

peuvent causer des blessures graves à des personnes. Le

gazon doit toujours être soigneusement examiné et libre de

tout objet avant chaque tonte.

• Si la tondeuse à gazon frappe un objet étranger,

suivez ces étapes:

1. Arrêtez la tondeuse à gazon. Relâchez l’anse.

2. Retirez les blocs-piles et la clé de sûreté.

3. Inspectez pour tout dommage.

4. Réparez tout dommage avant de redémarrer et

d’utiliser la tondeuse à gazon.

• Utilisez seulement des lames de remplacement

identiques.

CONSERVEZ CES INSTRUCTIONS

Important

Pratiques sécuritaires pour les tondeuses

à pousser

Cette machine peut amputer les mains et les pieds et

projeter des objets. Ne pas respecter les instructions de

sécurité suivantes pourrait entraîner une blessure grave ou

la mort.

Renseignements généraux

1 . Lisez, comprenez et suivez les instructions et les

avertissements dans ce guide et sur la machine, le moteur

et les accessoires.

2 . Permettez seulement aux utilisateurs, qui sont responsables,

formés, qui connaissent bien les instructions et ayant les

capacités physiques nécessaires d’utiliser la machine.

3 . Ne pas utiliser la machine lorsque vous êtes sous l’influence

de l’alcool ou de la drogue.

Préparation avant l’utilisation

1 . Retirez tout objet de la zone d’utilisation qui pourrait être

projeté ou nuire à l’utilisation de la machine.

2 . Gardez tous les passants à l’écart de la zone d’utilisation,

particulièrement les jeunes enfants et les animaux de

FRANÇAIS

L’étiquette sur votre outil peut comporter les symboles suivants.

Les symboles et les définitions sont les suivants:

BPM .................... battements par

minute

V ......................... volts

min ..................... minutes

ou CC ........... courant continu

…/min ..............par minute

Tr/min ................ tours par minute

A ......................... ampères

Hz .......................hertz

W ........................watts

Wh ......................Wattheures

..................... vitesse à vide

n .........................vitesse nominale

..................... symbole d’alertes

de sécurité

..................... portez une

protection

respiratoire

Les objets frappés par la lame de la tondeuse

peuvent causer une blessure grave. Restez

derrière la poignée lorsque le moteur

fonctionne. Assurez-vous toujours que les

personnes et les animaux sont éloignés de

l’éjection provenant de la tondeuse durant

l’utilisation. Inspectez toujours la zone de

tonte avant de tondre et retirez les objets qui

pourraient être projetés par la lame. Relâchez

l’anse pour éteindre la tondeuse et attendez

que la lame cesse de tourner (environ 3

secondes) avant de traverser le trottoir, les

routes, le patio et les entrées en gravier.

Renseignements de sécurité

supplémentaires



AVERTISSEMENT: Ne jamais modifier l’outil

électrique ou toute pièce de celui-ci. Cela pourrait

entraîner des dommages matériels ou des blessures

corporelles.



AVERTISSEMENT: Portez TOUJOURS des lunettes

de sécurité. Les lunettes de tous les jours NE SONT

PAS des lunettes de sécurité. De plus, utilisez un

masque facial ou antipoussière si l'opération de coupe

est poussiéreuse. Portez une protection auditive si

l’opération de tonte est bruyante. PORTEZ TOUJOURS

UN ÉQUIPEMENT DE SÉCURITÉ CERTIFIÉ:

• Protection oculaireANSI Z87.1 (CAN/CSA Z94.3),

• protection auditive ANSI S12.6 (S3.19),

• protection respiratoire NIOSH/OSHA/MSHA.



AVERTISSEMENT: Certaines poussières créées par ce

produit contiennent des produits chimiques reconnus

dans l’État de la Californie pour causer le cancer, des

anomalies congénitales ou autres effets nuisibles sur

la reproduction. Certains exemples de ces produits

chimiques sont:

• des composants de fertilisants

• des composants d'insecticides, d'herbicides et de

pesticides

• de l’arsenic et du chrome provenant du bois de

construction traité chimiquement.

Pour réduire votre exposition à ces produits chimiques, porter

un équipement de sécurité approuvé, comme un masque

antipoussière spécialement conçu pour filtrer les particules

microscopiques.

2 . Tondez en vous déplaçant en travers des pentes; jamais vers

le haut ou vers le bas. Soyez prudent lorsque vous utilisez la

tondeuse près de déclins, fossés ou remblais.

3 . Évitez de tondre le gazon mouillé. (Si vos pieds ne sont

pas d’aplomb, une glissage et une chute accidentelle sont

possibles)

4 . Ne pas utiliser la machine dans le cas où la traction, la

direction ou la stabilité remise en question. La tondeuse

pourrait glisser même si les roues sont arrêtées.

5 . Évitez les démarrages ou les arrêts sur les pentes. Évitez de

changer soudainement de vitesse ou de direction. Tournez

lentement et graduellement.

6 . Soyez très prudent lorsque vous utilisez la machine avec un

sac à herbe ou un (des) autre(s) accessoire(s). Ils peuvent

affecter la stabilité de la machine.

Réparer

1 . Gardez la machine en bon état de fonctionnement.

Remplacez les pièces usées ou endommagées.

2 . Soyez prudent lorsque vous entretenez les lames.

Enveloppez la (les) lame(s) ou portez des gants. Remplacez

les lames endommagées. Ne pas réparer ou altérer la (les)

lame(s). Maintenez tous les écrous et boulons serrés.

3 . Gardez la tondeuse libre de toute herbe, feuille ou autre

accumulation de débris.

4 . Entretenez ou remplacez les étiquettes d’instructions et de

sécurité selon les besoins.

Les éléments suivants sont des explications des symboles

de danger et sécurité importants sur la tondeuse.

L’utilisateur doit litre et comprendre le manuel

d'instructions.

Afin d’éviter le risque de blessure grave, ne pas

tondre les pentes vers le haut et vers le bas.

Tondez toujours en travers de pentes.

Afin d’éviter le risque de blesser les passants,

gardez toutes les personnes et tous les animaux

à une distance sécuritaire de la tondeuse

durant l’utilisation.

Les lames en rotation peuvent causer de graves

blessures. Gardez les mains et les pieds loin

du châssis de la tondeuse et de l’ouverture

d’éjection en tout temps. Assurez-vous toujours

que la lame est arrêtée. Relâchez l’anse pour

éteindre la tondeuse et attendez que la lame

cesse de tourner (environ 3 secondes) et

retirez la clé de sécurité et les blocs-piles avant

de retirer ou de remettre en place le bac de

collecte de l’herbe, de nettoyer, d’entretenir, de

transporter ou de soulever la tondeuse.

FRANÇAIS

ou à une température au-dessus de 129°C (265°F) pourrait

causer uneexplosion.

• Si le liquide des piles entre en contact avec la peau,

lavez immédiatement avec de l'eau et du savon doux.

Si le liquide vient en contact avec les yeux, rincez à l'eau

courante durant 15minutes, ou jusqu'à ce que l'irritation

cesse, en gardant les yeux ouverts. Pour information de

consultation médicale, l'électrolyte des piles est composé

d'un mélange organique liquide et de sels delithium.

• Le contenu des piles peut causer une irritation

respiratoire. Faites circuler de l'air frais. Si les symptômes

persistent, consultez unmédecin.

• Le liquide des piles peut être inflammable s’il est

exposé aux étincelles ou auxflammes.

• Ne jamais tenter d'ouvrir le bloc‑piles pour quelque

raison que ce soit. Si le boîtier du bloc‑piles est fendu

ou endommagé, ne pas l'insérer dans le chargeur. Ne

pas écraser, échapper ou endommager le bloc-piles. Ne pas

se servir d'un bloc-piles ou chargeur qui a subi un impact,

a été échappé, renversé par un véhicule ou endommagé

d'une façon ou d'une autre (par ex. perforé par un clou,

frappé par un marteau, sur lequel on a marché). Les

blocs-piles endommagés devraient être amenés/expédiés

au centre de service pourrecyclage.

Recommandations d’entreposage

Le meilleur lieu pour l'entreposage est un endroit frais et sec

loin de la lumière directe du soleil et de la chaleur ou du froid

excessif. Entreposez le bloc-piles entièrement chargé hors

duchargeur.

Instructions de nettoyage du bloc‑piles

La saleté et la graisse peuvent être retirées des surfaces

extérieures du bloc-piles à l'aide d'un linge ou d’une

brosse souple non métallique. Ne pas utiliser d'eau ou de

solutionnettoyante.

Blocs‑piles du niveau de la jauge de carburant

(Fig. B)

Certains blocs-piles incluent une jauge de carburant.

Lorsque vous appuyez et maintenez, les voyants DEL

indiqueront le niveau approximatif de charge restante. Cela

n’indique pas la fonctionnalité de l’outil et peut varier selon

les accessoires utilisés, la température et l'utilisation de

l’utilisateurfinal.

Transport



AVERTISSEMENT : danger d'incendie. Ne pas

entreposer ou transporter le bloc‑piles de manière

à ce que des objets métalliques puissent entrer

en contact avec les bornes des piles exposées. Par

exemple, ne pas placer le bloc-piles dans des tabliers,

des poches, des coffres à outils, des boîtes d’ensembles

de produits, des tiroirs, etc. avec des clous, des vis,

des clés, les pièces de monnaie, les outils à main, etc.

Lorsque vous transportez des blocs-piles individuels,

assurez-vous que leurs bornes sont protégées et bien

isolées de tout matériel avec lequel elles pourraient

entrer en contact et causer un court-circuit.

LISEZ TOUTES LES INSTRUCTIONS

Consignes de sécurité importantes pour

les blocs‑piles



AVERTISSEMENT : lisez toutes les consignes

de sécurité, les instructions et les symboles

d’avertissements du bloc‑piles, du chargeur et du

produit. Ne pas suivre les avertissements et les

instructions peut entraîner un choc électrique, un

incendie et/ou des blessuresgraves.

• Ne pas charger ou utiliser le bloc‑piles en

atmosphères explosibles comme la présence de

liquides inflammables, de gaz ou de poussière. Insérer

ou retirer la pile du bloc-piles peut enflammer la poussière

ou lesvapeurs.

• Ne JAMAIS forcer le bloc‑piles dans le chargeur.

NE PAS modifier le bloc‑piles de quelque façon

que ce soit dans un chargeur non compatible

puisque le bloc‑piles peut se briser causant une

blessurecorporelle. Consultez le tableau à la fin de ce

guide pour la compatibilité des blocs-piles et deschargeurs.

• Chargez les blocs‑piles seulement dansCRAFTSMAN.

• NE PAS éclabousser ou immerger dans l’eau ou tout

autreliquide.

• NE PAS laisser l’eau ou tout liquide entre dans le bloc-piles.

• Ne pas entreposer ou utiliser l’outil et le bloc‑piles

dans des endroits où la température peut atteindre

ou excéder 40°C (104°F) (comme les remises

extérieures ou les édifices en métal durant l’été). Pour

une meilleure durée de vie, entreposez le bloc-piles dans un

endroit frais etsec.

REMARQUE: Ne pas ranger les blocs‑piles dans un

outil avec la gâchette verrouillée. Ne jamais coller la

gâchette avec du ruban adhésif en positionMarche.

• Ne pas brûler le bloc‑piles même s’il est gravement

endommagé ou est entièrement usé. Le bloc-piles

peut exploser au cours d’un incendie. Des vapeurs et des

matières toxiques sont produites lorsque les blocs-piles au

lithium-ion sontbrûlés.

• Ne pas exposer de bloc‑piles ou l’outil aux flammes ou

à des températures excessives. L’exposition aux flammes

PILES ET CHARGEURS

Le bloc-piles n’est pas entièrement chargé lorsqu’il sort de

la boîte. Avant d'utiliser le bloc-piles et le chargeur, lisez

attentivement les instructions de sécurité suivantes, puis

suivez les procédures de chargement énoncées. Lorsque vous

commandez des blocs-piles de remplacement, assurez-vous

d’inclure le numéro du catalogue et latension.

..................... portez une

protection oculaire

..................... Construction de

classe II (à isolation

double)

..................... portez une

protection auditive

..................... lisez toute la

documentation

..................... évitez de fixer la

lumière

ou CA ...........courant alternatif

Ah ....................... ampères-heures

La page charge ...

Craftsman CMCMW220P2 Le manuel du propriétaire

Marque: Craftsman

Modèle: CMCMW220P2

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Craftsman CMCMW220P2 Owner's manual
español: Craftsman CMCMW220P2 El manual del propietario

Craftsman CMCMW220P2 Le manuel du propriétaire

Craftsman CMCMW220P2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents