Maytag W10343072D Mode d'emploi

Marque: Maytag

Modèle: W10343072D

Catégorie: Machines à laver

Taper: Mode d'emploi

Ce manuel convient également à

W10343072C

W10376241C - SP

WASHER/DRYER

USE AND CARE GUIDE

Table of Contents

WASHER/DRYER SAFETY ...........................................................2

ACCESSORIES ...................................................................................4

USING LESS WATER AND ENERGY .......................................4

CHECK YOUR VENT SYSTEM

FOR GOOD AIR FLOW ....................................................................4

CONTROL PANEL AND FEATURES .........................................5

WASHER CYCLE GUIDE ................................................................6

DRYER CYCLE GUIDE .....................................................................7

USING YOUR WASHER ..................................................................8

USING YOUR DRYER ...................................................................11

WASHER/DRYER MAINTENANCE ........................................12

TROUBLESHOOTING ...................................................................16

WARRANTY ......................................................................................... 22

ASSISTANCE OR SERVICE ................................... Back Cover

Table des matières

SÉCURITÉ DE LA LAVEUSE/SÉCHEUSE ........................23

ACCESSOIRES ................................................................................25

RÉDUCTION DE LA CONSOMMATION D’EAU

ET D’ÉNERGIE .................................................................................. 25

VÉRIFICATION D’UNE CIRCULATION

D’AIR ADÉQUATE POUR LE SYSTÈME

D’ÉVACUATION ...............................................................................26

TABLEAU DE COMMANDE ET

CARACTÉRISTIQUES ...................................................................27

GUIDE DE PROGRAMMES DE LA LAVEUSE .................. 28

GUIDE DE PROGRAMMES DE LA SÉCHEUSE .............29

UTILISATION DE LA LAVEUSE ................................................30

UTILISATION DE LA SÉCHEUSE ...........................................33

ENTRETIEN DE LA LAVEUSE/SÉCHEUSE ......................35

DÉPANNAGE .....................................................................................39

GARANTIE ........................................................................................... 47

ASSISTANCE OU SERVICE .................... Couverture arrière

LAVEUSE/SÉCHEUSE GUIDE

D’UTILISATION

ET D’ENTRETIEN

WASHER/DRYER SAFETY

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW

Good airﬂow

Along with heat, dryers require good airﬂow to efﬁciently dry

laundry. Proper venting will reduce your drying times and

improve your energy savings. See Installation Instructions.

The venting system attached to the dryer plays a big role in

good airﬂow.

Service calls caused by improper venting are not covered by

the warranty and will be paid by the customer, regardless of

who installed the dryer.

Maintain good airﬂow by:

Good Better

Cleaning your lint screen before each load.

Replace plastic or foil vent material with 4" (102 mm)

diameter heavy, rigid vent material.

Use the shortest length of vent possible.

Use no more than four 90° elbows in a vent system;

each bend and curve reduces air ﬂow.

Remove lint and debris from the exhaust hood.

Remove lint from the entire length of the vent system

at least every 2 years. When cleaning is complete, be

sure to follow the Installation Instructions supplied with

your dryer for ﬁnal product check.

Clear away items from the front the dryer.

(102 mm)

ACCESSORIES

This washer does not include inlet water hoses.

See Installation Instructions for installation accessories.

Enhance your washer with these premium accessories.

For more high-quality items or to order, call 1-800-901-2042,

or visit us at www.maytag.com/accessories. In Canada

call 1-800-807-6777, or visit us at www.whirlpoolparts.ca.

Part Number

Accessory:

8212526 Washer drip tray, ﬁts under all

All-purpose appliance cleaner

31682

Laundry supply storage cart

1903WH

Use Sensor Dry cycles for better fabric care and energy savings

Use the Sensor Dry cycles to provide the most energy savings and enhanced fabric care from the dryer. During Sensor Dry cycles,

drying air temperature or moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer shuts off

when the load reaches the selected dryness. The Energy Preferred cycle will provide optimal energy savings.

With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to

over-drying. Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.

USING LESS WATER AND ENERGY

This washer is designed to use less water and energy, and complies

with all 2011 energy standards. Wash cycles with controlled

temperatures are designed to maintain cleaning performance while

using less water and energy compared to older traditional washers.

As a result, water levels will be lower, and hot and warm wash

temperatures may not be as warm as you are used to.

Traditional washer

Reduced water washer

CONTROL PANEL AND FEATURES

WASH CYCLE KNOB

Use the Wash Cycle knob to select available cycles on your

washer. Turn the knob to select a cycle for your laundry load.

See “Cycle Guide” for detailed descriptions of cycles.

WASH TEMPERATURE

You may select a Wash Temperature based on the type of fabric

and soils being washed. Use the warmest wash water safe for

the fabric. Follow garment label instructions.

WATER LEVEL

Use this option to adjust the amount of water used with your

load size. Use enough water to allow the load to move freely.

NOTE: The highest water level will be lower than that

of pre-2011 washers.

FABRIC SOFTENER

This option must be selected if using fabric softener

during a cycle. It ensures that fabric softener is added

at the correct time in the rinse for even distribution.

Not all features and options are available on all models.

Appearance may vary.

5 6

PUSH TO START/END OF CYCLE SIGNAL

The End of Cycle Signal produces an audible sound when the

drying cycle is ﬁnished. Promptly removing clothes at the end

of the cycle reduces wrinkling.

Turn the END OF CYCLE SIGNAL knob to select the desired

setting (On or Off). Press the PUSH TO START knob to start

the dryer.

DRYER CYCLE KNOB

Use your Dryer Cycle knob to select available cycles on

your dryer. Turn the knob to select a cycle for your laundry load.

See “Cycle Guide” for detailed descriptions of cycles.

TIMED DRY

Will run the dryer for the speciﬁed time on the control.

Drying time and temperature will depend on your dryer

model.

SENSOR DRY

Senses moisture in the load or air temperature and shuts off

when the load reaches the selected dryness level. Gives the

best drying in the shortest time. Drying time will vary based

on fabric type, load size, and dryness setting.

WASHER

DRYER

* You should use the amount of detergent or presoak additive recommended by the manufacturer. After the cycle ends, you may add

detergent and start a new wash cycle.

** Approximate time in minutes.

IMPORTANT: Do not presoak items in your washer by lifting the lid or stopping the cycle. Failure to follow this instruction can result in

property damage. If needed, presoak items in a small wash basin prior to loading the washer.

WASHER CYCLE GUIDE

Items to wash:

Cycle:

Wash Times**:

Wash/Spin

Speed:

Cycle Details:

Light to moderately

soiled delicate items

and washable knits

Delicate

Low/Low

Permanent press

blends and synthetic

fabrics that are

lightly to moderately

soiled

Cottons and linens;

loads that are

moderately or heavily

soiled

Heavily soiled

or stained

items that need

pretreatment

Casual

Normal

Prewash*

Gently removes soils and minimizes wrinkling.

Features a cool down, rinse and low-speed ﬁnal spin

to reduce wrinkling.

You may select a wash time based on the soil level of

your load.

Brief periods of agitation and soak followed by a

4-minute Pre-Wash featuring high-speed agitation.

6–10

6–14

High and

Low/Low

High and

Low/High

High/High

6–10

Not all cycles or options are available on all models.

Refer to the cycle control knob on your washer.

Wash temperatures are selected using the Wash Temperature

control knob.

For best performance:

• Choosethecyclethatbesttstheloadbeingwashed.

• UsePrewashforheavilysoiledclothing.

• Donotleavethewasherlidopenunattendedoncethewasherhas

started to ﬁll.

DRYER CYCLE GUIDE — SENSOR DRY CYCLES

Not all cycles and settings are available on all models.

SENSOR DRY – Sensor dry cycles give the best drying in the

shortest time. They sense moisture in the load or air temperature and

shut off when the load reaches the selected dryness level. Drying

time varies based on fabric type, load size, and dryness setting.

Select a drying temperature based on the fabrics in your load. If you

are unsure of the temperature to select for a load, select the lower

setting rather than the higher setting.

Items to dry:

Available

Options:

Cycle Details:

End of Cycle Signal

NOTE: If loads do not seem as dry as you would like, select More Dry next time you dry a similar load. If loads seem drier than you like, select

Less Dry next time you dry a similar load.

SENSOR DRY

(Low Heat)

SENSOR DRY

(High Heat)

End of Cycle Signal Sensor Dry cycles include a cool down cycle to make the load

easier to handle.

An ENERGY PREFERRED cycle (*) is available for optimal

energy savings.

Cycle:

DRYER CYCLE GUIDE — TIMED DRY

Items to dry:

Temperature:

Cycle:

Available

Options:

Cycle Details:

Not all cycles and settings are available on all models.

Will run the dryer for the selected time.

Heavy, bulky, or

lightweight items

Timed Dry

Time Adjustment

End of Cycle Signal

Completes drying if items are still damp.

High

Rubber, plastic,

heat-sensitive fabrics

Air Fluff

No Heat

Time Adjustment

End of Cycle Signal

No-heat drying.

Any load Wrinkle Prevent No Heat Time Adjustment

End of Cycle Signal

Helps remove wrinkles, such as those

found in clothes packed in a suitcase

or in items wrinkled from being left in

the dryer too long.

Most loads, including

jeans, heavy work

clothes, towels

Medium to lightweight

synthetics, permanent

press, no-iron items or

smaller, lighter loads,

including work clothes,

medium weight fabrics,

sheets, casual, shirts,

pants, lightweight items,

synthetics, delicates,

athletic wear

• Emptypockets.Loosechange,buttons,oranysmallobject

can pass under the agitator and become trapped, causing

unexpected sounds.

• Sortitemsbyrecommendedcycle,watertemperature,

and colorfastness.

• Separateheavilysoileditemsfromlightlysoiled.

• Separatedelicateitemsfromsturdyfabrics.

• Donotdrygarmentsifstainsremainafterwashing,because

heat can set stains into fabric.

• Treatstainspromptly.

• Closezippers,fastenhooks,tiestringsandsashes,and

remove non-washable trim and ornaments.

• Mendripsandtearstoavoidfurtherdamagetoitems

during washing.

Helpful Tips:

• Whenwashingwater-prooforwater-resistantitems,loadevenly.

• Usemeshgarmentbagstohelpavoidtanglingwhenwashing

delicate or small items.

• Turnknitsinsideouttoavoidpilling.Separatelint-takersfrom

lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint

from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to avoid

damage to your garments.

1. Sort and prepare your laundry

Add a measured amount of detergent or single-dose laundry

packet into the basket before adding clothes. If using Oxi-type

boosters, color-safe bleach, or fabric softener crystals, add to

the bottom of the washer basket as well.

IMPORTANT: Follow the manufacturer’s instructions to

determine the amount of laundry products to use.

2. Add laundry products

USING YOUR WASHER

5. Add fabric softener to dispenser

(on some models)

Pour a measured amount of liquid fabric

softener into dispenser, always follow

manufacturer’s directions for correct amount

of fabric softener based on your load size.

Dilute liquid fabric softener by ﬁlling the dispenser with warm

water until liquid reaches the underside of the rim. See max ﬁll line

arrows. Do not overﬁll.

IMPORTANT: Fabric Softener option must be selected to “On”

to ensure proper distribution at correct time in cycle.

Adding Liquid Fabric Softener Manually to Wash Load

During the ﬁnal rinse, wait until the washer has completed ﬁlling,

push in the Cycle knob to pause the washer. Lift the lid and add

the measured recommended amount of liquid fabric softener

(diluted with 1/2 to 1 cup [125 to 250 mL] warm water). Do not

allow liquid fabric softener to spill, splash, drip, or run into the basket

or on load. Do not use more than the recommended amount. Close

the lid and pull out the Cycle knob to start the washer.

IMPORTANT: Fabric Softener option must be selected to “On”

to ensure proper distribution of the fabric softener during the rinse

portion of the cycle.

4. Add liquid chlorine bleach

to dispenser

Liquid

Chlorine Bleach

Do not overﬁll, dilute, or use more than 1 cup (250 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

Load garments in loose heaps evenly around basket wall.

For best results, do not pack the load tightly. Do not wrap large

items such as sheets around the agitator; load them in loose piles

around the sides of the basket. Try mixing different sized items to

reduce tangling.

3. Load laundry into washer

MAX FILL

Turn Cycle knob clockwise to choose your wash cycle.

For more information, see “Cycle Guide.”

6. Select cycle

IMPORTANT: Do not tightly pack or force items into washer.

Items need to move freely for best cleaning and to reduce

wrinkling and tangling.

Wash Temp

Hot

Some cold water is added to save

energy. This will be cooler than your

hot water heater setting.

Warm

Some cold water will be added, so

this will be cooler than what your

previous washer provided.

Cool

Warm water may be added to

assist in soil removal and to help

dissolve detergents.

Cold

This is the temperature from your

faucet. If your tap cold water is very

cold, warm water may be added

to assist in soil removal and help

dissolve detergent.

Suggested Fabrics

8. Select WASH TEMPERATURE

Once you select a cycle, select the desired wash temperature

by turning the WASH TEMPERATURE knob to the appropriate

setting based on your load. All rinses are tap cold.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your garments.

10. Pull out Cycle knob to begin wash

cycle

Close the washer lid and pull out the Cycle knob to start the

washer.

NOTE: Some washers will only ﬁll with the lid in the closed

position.

To add a garment after washer starts:

• PushintheCycleknobtostopthewasher.

• Openthelidandaddtheitem(s).

• ClosethelidandpulltheCycleknobouttoresumethecycle.

Do not leave the lid open unattended once the washer has

started ﬁlling.

• Forbestperformancedonotinterruptwashercycleoncethe

washer has been started.

Set FABRIC SOFTENER to ON if you want to add fabric softener.

IMPORTANT: Fabric Softener option must be selected to “On” to

ensure proper distribution at correct time in cycle.

Whites and pastels

Durable garments

Heavy soils

Bright colors

Moderate to light soils

Colors that bleed

or fade

Light soils

Dark colors that

bleed or fade

Light soils

9. Select FABRIC SOFTENER On or Off

Select the load size setting most suitable for your load. Small will

add a low amount of water for smaller loads and Large will add

the most amount of water for large or bulky loads. Items need to

move freely.

7. Select WATER LEVEL

USING YOUR DRYER

1. Clean the lint screen

Clean the lint screen before each load. Pull the lint screen straight

up. Roll lint off the screen with your ﬁngers. Do not rinse or wash

screen to remove lint. Push the lint screen ﬁrmly back into place.

For additional cleaning information, see “Cleaning the Lint Screen.”

2. Load the dryer

Place laundry in the dryer. Close the door.

NOTE: Your model may have a different door than the one shown.

Some models have drop down doors.

Do not tightly pack the dryer; clothes should be able to

tumble freely.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this dryer.

Before using your dryer, wipe the dryer drum with a damp cloth

to remove dust from storing and shipping.

3. Select cycle

Select the desired cycle for your load. See “Cycle Guide”

for more information about each cycle.

SENSOR DRY Cycles

You can select a different dryness level, depending on your load,

by turning the knob to dryness level.

Selecting More Dry, ENERGY PREFERRED, or Less Dry

automatically adjusts the dryness level at which the dryer will shut

off. Once a dry level is set, it cannot be changed without stopping

the cycle.

SENSOR DRY cycles give the best drying in the shortest time.

Drying time varies based on fabric type, load size, and dryness

setting.

NOTE: More Dry removes more load moisture. ENERGY

PREFERRED is used for a starting point for SENSOR DRY

cycles. Choose ENERGY PREFERRED for optimal energy

savings. Less Dry removes less moisture and is used for loads

you may want to put on a hanger to complete drying.

5. Press PUSH TO START to

begin cycle

Push and hold the PUSH TO START knob to begin the cycle.

Promptly remove garments after cycle has completed to reduce

wrinkling. Use the Wrinkle Prevent feature to avoid wrinkling when

you are unable to remove a load from the dryer as soon as it stops.

4. Select End of Cycle signal

(optional)

Your dryer may have an End of Cycle signal. The signal is helpful

when drying items that should be removed from the dryer as

soon as it stops. The End of Cycle signal is part of the PUSH

TO START button and is selectable. Turn the PUSH TO START

button to ON or OFF. The signal will sound only if the selector is

set to ON.

NOTE: When the Wrinkle Prevent setting is selected and the End

of Cycle signal is on, the tone will sound every 5 minutes until the

clothes are removed or the Wrinkle Prevent setting ends.

Replace inlet hoses after 5 years of use to reduce the risk of hose

failure. Periodically inspect and replace inlet hoses if bulges, kinks,

cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement on

the label with a permanent marker.

WATER INLET HOSES

WASHER/DRYER MAINTENANCE

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at its Best

1. Always follow the detergent manufacturer’s instructions

regarding the amount of detergent to use. Never use more than

the recommended amount because that may increase the rate

at which detergent and soil residue accumulate inside your

washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better job

of controlling the rate at which soils and detergent accumulate.

3. Always leave the washer lid open between uses to help dry out

the washer and prevent the buildup of odor-causing residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This Washer

Maintenance Procedure should be performed, at a minimum, once

per month or every 30 wash cycles, whichever occurs sooner,

to control the rate at which soils and detergent may otherwise

accumulate in your washer. To keep washer interior odor-free,

follow this recommended monthly cleaning procedure:

affresh

Washer Cleaner Cycle Procedure (Recommended for

Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affesh

Washer Cleaner tablet in the bottom of

the washer basket.

c. Do not add any detergent or other chemical to the

washer when following this procedure.

d. Close the washer lid.

e. Select Normal Heavy cycle, Hot Temperature, and High

Water Level.

f. Pull out the Cycle knob. Water will pour into washer

for a moment and then pause; the lid will lock and

the cycle will continue.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, push in the Cycle knob.

Keep washer/dryer area clear and free from items that would

block the airﬂow for proper washer/dryer operation. This

includes clearing piles of laundry in front of the washer/dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum

1. Apply a liquid, nonﬂammable household cleaner to the

stained area of the drum and rub with a soft cloth until stain

is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum.

NOTE: Garments that contain loose dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will not

stain future loads of clothes. Dry these items inside out to avoid

drum staining.

REMOVING ACCUMULATED LINT

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualiﬁed servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

CLEANING THE WASHER/DRYER LOCATION

WASHER CARE

Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing

or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Do not add any detergent or other chemical to the

washer when following this procedure.

d. Close the washer lid.

e. Select Normal Heavy cycle, Hot Temperature, and

High Water Level

f. Pull out the Cycle knob. Water will pour into washer

for a moment and then pause; the lid will lock and

the cycle will continue.

NOTE: For best results, do not interrupt cycle. If cycle must

be interrupted, push in the Cycle knob.

Cleaning the liquid fabric softener dispenser

1. Remove dispenser by grasping top with both hands and

squeezing, while pushing upward with thumbs.

2. Rinse dispenser under warm water, then replace it.

NOTE: To avoid damage to the washer or clothing,

do not wash clothes with the liquid fabric softener

dispenser removed.

Cleaning the bleach dispenser

Wipe the inside of the bleach dispenser with a clean, damp

cloth.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills. Use

only mild soaps or cleaners when cleaning external washer

surfaces.

IMPORTANT: To avoid damaging the washer’s ﬁnish, do not use

abrasive products.

CHANGING THE DRUM LIGHT (on some models)

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Using a Phillips-head screwdriver, remove

the screw located in the lower right-hand corner of the cover.

Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 10-watt

appliance bulb only. Replace the cover and secure with the

screw.

4. Plug into a grounded outlet or reconnect power.

CLEANING THE LINT SCREEN

Every load cleaning

The lint screen is located in the door opening of the dryer.

A screen blocked by lint can increase drying time.

To clean:

1. Pull the lint screen straight up. Roll lint off the screen with

your ﬁngers. Do not rinse or wash screen to remove lint.

Wet lint is hard to remove.

2. Push the lint screen ﬁrmly back into place.

IMPORTANT:

Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can cause

overheating and damage to both the dryer and fabrics.

If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

“Venting Requirements.”

As needed cleaning

Laundry detergent and fabric softener residue can build up

on the lint screen. This buildup can cause longer drying times

for your clothes, or cause the dryer to stop before your load is

completely dry. The screen is probably clogged if lint falls off

while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your ﬁngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel.

Reinstall screen in dryer.

VACATION, STORAGE, AND MOVING CARE

Non-Use or Storage Care

Operate your washer/dryer only when you are at home.

If you will be on vacation or not using your washer/dryer

for an extended period of time, you should:

1. Unplug washer/dryer or disconnect power.

2. Turn off water supply to washer, to avoid ﬂooding due

to water pressure surge.

3. For gas dryers only: Close shut-off valve to gas supply line.

4. Clean lint screen. See “Cleaning the Lint Screen.”

Moving Care

For power supply cord-connected washer/dryers:

1. Unplug the power supply cord.

2. Make sure leveling legs are secure in washer/dryer base.

3. Continue with “For washers” on next page.

For direct-wired washer/dryers:

1. Turn off power at fuse or breaker box.

2. Disconnect wiring.

3. Make sure leveling legs are secure in washer/dryer base.

4. Continue with “For washers” on next page.

For gas washer/dryers:

1. Unplug or disconnect power to washer/dryer.

2. Close shut-off valve in gas supply line.

3. Disconnect gas supply line pipe and remove ﬁttings

attached to dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in washer/dryer base.

6. Continue with “For washers” on next page.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer/dryer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer/dryer. If storing or moving

during freezing weather, winterize your washer/dryer.

To winterize washer/dryer:

1. Shut off both water faucets, disconnect and drain water inlet

hoses.

2. Put 1 qt. (1 L) of R.V. - type antifreeze in basket and run

washer on RINSE cycle for about 30 seconds to mix

antifreeze and remaining water.

3. Unplug washer/dryer or disconnect power.

VACATION, STORAGE, AND MOVING CARE (cont.)

For washers:

1. Shut off both water faucets. Disconnect and drain water inlet

hoses.

2. If washer/dryer will be moved during freezing weather,

follow “Winter Storage Care” directions before moving.

3. Disconnect drain from drain system and drain any

remaining water into a pan or bucket. Disconnect drain hose

from back of washer.

4. Place inlet hoses and drain hose inside washer basket.

5. Drape power cord over edge and into washer basket.

6. Place packing tray from original shipping materials back inside

washer/dryer. If you do not have packing tray, place heavy

blankets or towels into basket opening. Close doors and place

tape over doors and down front of washer/dryer. Keep doors

taped until washer/dryer is placed in new location.

REINSTALLING/USING WASHER/DRYER AGAIN

To reinstall washer/dryer after non-use, vacation, moving

or winter storage:

1. Refer to Installation Instructions to locate, level, and

connect washer/dryer.

2. Before using again, run washer/dryer through the following

recommended procedure:

To use washer/dryer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

(continued in next column)

2. Plug in washer/dryer or reconnect power.

3. Run washer through a complete cycle to clean washer

and remove antifreeze, if used. Use half the manufacturer’s

recommended amount of detergent for a medium-size load.

In the U.S.A.

In Canada

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.

If you experience

Possible Causes

Solution

Feet may not be in contact with the

ﬂoor and locked.

Front and rear feet must be in ﬁrm contact with ﬂoor, and

washer/dryer must be level to operate properly. Jam nuts must be

tight against the bottom of the cabinet.

Check ﬂoor for ﬂexing or sagging. If ﬂooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer/dryer will reduce

sound.

See “Level the Washer/Dryer” in Installation Instructions.

Load could be unbalanced. Load dry items in loose heaps evenly around basket wall. Adding

wet items to washer or adding more water to basket could

unbalance washer.

Do not tightly pack. Avoid washing single items.

See “Cycle Guide” and “Using Your Washer” in this Use and

Care Guide.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump.

It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

Objects caught in washer drain

system.

Clicking or metallic noises

Gurgling or humming

It is normal to hear the pump making a continuous humming sound

with periodic gurgling or surging as ﬁnal amounts of water are

removed during the Spin cycle.

Washer may be draining water.

Check the following for

proper installation or

see “Using Your

Washer” section.

Washer/dryer may not be level.

Vibration or Off-Balance

Noises

TROUBLESHOOTING – WASHER

Washer not level.

Water may splash off basket if washer is not level. Check that load

is not unbalanced or tightly packed.

Fill hoses not attached tightly.

Tighten ﬁll-hose connection.

Make sure all four ﬁll hose ﬂat washers are properly seated.

Drain hose connection.

Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Check household plumbing for leaks or

clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check

all household plumbing for leaks (laundry tubs, drain pipe, water

pipes, and faucets.)

Fill hose washers.

Check the following for

proper installation:

Improper loading can cause basket to be out of alignment

and cause water to splash off tub. See “Using Your Washer”

for loading instructions.

Washer not loaded as

recommended.

Water Leaks

Washer not performing as expected

Washer won’t run

or ﬁll, washer stops

working

Check for proper water supply.

Both hoses must be attached and have water ﬂowing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ﬂow.

Humming

You may hear the hum of the sensing spins after you have started

the washer. This is normal. Sensing spins will take several minutes

before water is added to the washer.

Washer is in sensing spin.

TROUBLESHOOTING – WASHER cont.

In the U.S.A.

In Canada

If you experience

Possible Causes

Solution

Normal washer operation. Door must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer spins the dry load for several minutes before ﬁlling to

determine if load is balanced. You may hear the hum of the spins.

This is normal.

Washer not loaded as

recommended.

Remove several items, rearrange load evenly in basket and add

detergent. Close door and press PUSH TO START.

Do not add more than 1 or 2 additional items after cycle has started

to avoid tightly packing or unbalancing.

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.

Washer not performing as expected (cont.)

Use a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/speed spin for

your garment. To remove extra water in the load, select Spin. Load

may need to be rearranged to allow even distribution of the load in

the basket.

Small items may have been caught in pump or between basket and

tub, which can slow draining.

Empty pockets and use garment bags

for small items.

Washer not draining/

spinning, loads are

still wet

Washer not loaded as recommended. Tightly packing or unbalanced loads will not allow the washer to

spin correctly, leaving the load wetter than normal. See “Using Your

Washer” for loading recommendations.

Check plumbing for correct drain hose

installation. Drain hose extends into

standpipe farther than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening. Lower drain hose if the end is higher than 96" (2.4 m)

above the ﬂoor. Remove any clogs from drain hose.

Washer won’t run

or ﬁll, washer stops

working (cont.)

Too much detergent causing suds

to slow or stop draining and spinning.

Always measure and follow detergent directions for your load.

To remove extra suds, select Rinse and Spin. Do not add

detergent.

Plug into a grounded outlet or reconnect power.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Check proper electrical supply.

If you experience

Possible causes

Solution

Incorrect or wrong

wash or rinse

temperatures

Check for proper water supply. Check that hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water ﬂowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

This washer uses cooler wash and rinse water temperatures

than your previous washer. This includes cooler hot and warm

washes.

Load not rinsed Check for proper water supply.

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.

Washer not performing as expected (cont.)

Energy-saving controlled

wash temperatures.

Check that hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water ﬂowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Using too much detergent.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

detergent directions based on load size and soil level.

Washer not loaded as recommended. The washer is less efﬁcient at rinsing when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

The washer will not rinse well if tightly packed. Load with dry items

only.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 garments after washer has started.

The high spin speeds combined with air ﬂow during the ﬁnal

spin can cause items near the top of the load to develop dry spots

during the ﬁnal spin. This is normal.

High speed spins extract more

moisture than traditional top-load

washers.

Add an extra rinse to the selected cycle. Heavy sand, pet hair, lint, and

detergent or bleach residues may

require additional rinsing.

Sand, pet hair, lint,

etc. on load after

washing

Load is tangling Washer not loaded as recommended. See “Using Your Washer” section.

Select a cycle with a slower wash action and spin speed;

however, items will be wetter than those using a higher

speed spin.

Load garments in loose heaps evenly around the basket wall.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

Not cleaning or

removing stains

Washer is less efﬁcient at cleaning when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Add only 1 or 2 garments after washer has started.

Washer not loaded as recommended.

TROUBLESHOOTING – WASHER cont.

Adding detergent on top of load. Add detergent, oxi products, and color-safe bleach to the

bottom of the basket before adding the load items.

Water level seems

too low, or the washer

appears to not ﬁll

completely

The top of the agitator is much higher

than the highest water level.

This is normal and necessary for clothes to move freely.

Clothes not completely

covered with water

This washer uses much less water

than traditional top-load washers.

Clothes may not be completely covered with water.

Dry spots on load

after cycle

Select a higher load-size setting, or wash a smaller load.

This washer uses much less water than

traditional top-load washers.

If you experience

Possible Causes

Solution

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.

Using too much detergent.

Not using correct cycle for fabric type.

Not using dispensers.

Not washing like colors together.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

manufacturer’s directions based on load size and soil level.

Use a higher soil level cycle option and warmer wash

temperature to improve cleaning.

Use Heavy cycle for tough cleaning.

Use dispensers to avoid chlorine bleach and fabric softener

staining.

Load dispensers before starting a cycle. Set FABRIC SOFTENER

to ON when using fabric softener.

Do not add products directly to load.

Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Washer not performing as expected (cont.)

Clogged dispenser.

Incorrect dispenser

operation

Fabric damage

Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have tangled.

Tie all strings and straps before starting wash load.

Items may have been damaged before

washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if load is

tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 garments after washer is started.

Monthly maintenance not done as

recommended.

See “Washer Care” in “Washer/Dryer Maintenance.”

Unload washer as soon as cycle is complete.

Be sure to measure correctly. Always follow the manufacturer’s

directions.

See “Washer Care” section.

Odors

Liquid chlorine bleach may have been

added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

Garment care instructions may not have

been followed.

Always read and follow garment manufacturer’s care label

instructions.

Using too much detergent.

Not cleaning or

removing stains (cont.)

Use only liquid chlorine bleach in the bleach dispenser. Use only

fabric softener in the fabric softener dispenser.

TROUBLESHOOTING – WASHER cont.

Single-dose laundry

packet not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before adding

clothes. Do not add packet to dispenser. Follow the manufacturer’s

instructions to avoid damage to your garments.

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

In U.S.A. www.maytag.com/help – In Canada www.maytag.ca.

If you experience

Possible Causes

Solution

TROUBLESHOOTING – DRYER

Door not closed completely. Make sure the dryer door is closed completely.

Household fuse is blown or circuit

breaker has tripped.

Electric dryers use 2 household fuses or circuit breakers.

The drum may be turning, but you may not have heat. Replace both

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

Dryer will not run

PUSH TO START knob not pressed

ﬁrmly or held long enough.

Incorrect power supply.

Electric dryers require 240-volt power supply.

Check with a qualiﬁed electrician.

Wrong type of fuse.

Use a time-delay fuse.

Unusual sounds Dryer had a period of non-use. If the dryer hasn’t been used for awhile, there may be a

thumping sound during the ﬁrst few minutes of operation.

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

The four legs are not installed, or the

dryer is not level front to back and side

to side.

The dryer may vibrate if not properly installed.

See Installation Instructions.

A coin, button, or paper clip is

caught between the drum and front

or rear of the dryer.

Clothing knotted or balled up.

When balled up, the load will bounce, causing the dryer to vibrate.

Separate the load items and restart the dryer.

Press and hold the PUSH TO START knob until you hear the dryer

drum moving.

It is a gas dryer.

The gas valve clicking is a normal operating sound.

Clothes are not drying

satisfactorily, drying

times are too long

Lint screen clogged with lint. Lint screen should be cleaned before each load.

The Air Fluff cycle has been selected.

Select the correct cycle for the types of garments being dried.

See “Cycle Guide.”

Load too large and heavy to dry

quickly.

Separate the load to tumble freely.

Exhaust vent or outside exhaust

hood clogged with lint, restricting air

movement.

Run the dryer for 5–10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not feel air

movement, clean exhaust system of lint or replace exhaust vent with

heavy metal or ﬂexible metal vent. Make sure vent is not crushed or

kinked. See Installation Instructions.

Exhaust vent diameter not the

correct size.

Use 4" (102 mm) diameter vent material.

Dryer located in a room with

temperature below 45ºF (7ºC).

Proper operation of dryer cycles requires temperatures above 45ºF

(7ºC).

Dryer located in a closet without

adequate opening.

Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum

of 1" (25 mm) of airspace, and, for most installations, the rear

of the dryer requires 5" (127 mm). See Installation Instructions.

Exhaust vent not the correct length.

Check that the exhaust vent is not too long or has too many turns.

Long venting will increase drying times. Make sure vent

is not crushed or kinked. See Installation Instructions.

Fabric softener sheets blocking

the grille.

Use only one fabric softener sheet, and use it only once.

Dryer not performing as expected

La page charge ...

Maytag W10343072D Mode d'emploi

Marque: Maytag

Modèle: W10343072D

Catégorie: Machines à laver

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag W10343072D User guide

Maytag W10343072D Mode d'emploi

Ce manuel convient également à

Maytag W10343072D Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents