Eneo IPB-62M2812M0A Quick Installation Manual

Marque: Eneo

Modèle: IPB-62M2812M0A

Catégorie: Des caméras de sécurité

Taper: Quick Installation Manual

Quick Installation Guide

1/2.8” Network Camera, 2MP,

1920x1080, Day&Night, D-WDR,

2.8-12mm, Infrared, Outdoor

IPB-62M2812M0A

Table of content

Parts supplied ..............................................................................................................5

Part names ....................................................................................................................6

Installation instructions ..............................................................................................7

Sunshield assembling ..................................................................................................................................................... 9

Pan & Tilt adjustments ...................................................................................................................................................8

Power supply connections ...........................................................................................................................................10

Quick Network Setup ..................................................................................................11

Web viewer description .............................................................................................................................................. 12

Player control & Display ......................................................................................................................................... 12

PTZ Control .................................................................................................................................................................. 13

Setup Menu Table ..................................................................................................................................................... 14

Quick Setup .................................................................................................................16

Information ...................................................................................................................................................................... 16

Users ................................................................................................................................................................................... 16

Add ................................................................................................................................................................................ 17

Edit .................................................................................................................................................................................. 17

Delete ............................................................................................................................................................................ 17

Date & Time ..................................................................................................................................................................... 18

Current Time ............................................................................................................................................................... 18

New Time...................................................................................................................................................................... 18

Time Zone .................................................................................................................................................................... 18

Day & Time Display ................................................................................................................................................... 18

Network ............................................................................................................................................................................. 19

Further information .................................................................................................. 20

Safety instructions

General safety instructions

•

• Keep the operating instructions in a safe place for later use.

• Installation, commissioning and maintenance of the system may only be carried out by authorised

individuals and in accordance with the installation instructions - ensuring that all applicable standards and

guidelines are followed.

• Protect the devices from water penetration and humidity, since these can cause lasting damage.

• Should moisture nevertheless enter the system, under no circumstance switch on the devices under these

conditions, instead send them for examination to an authorised specialist workshop.

•

• The device must be protected from excesses of heat, dust, humidity and vibration.

• When separating the system from the voltage supply, only ever use the plug to pull out the cable. Never

pull directly on the cable itself.

• Lay the connecting cables carefully and check that they are not mechanically stressed, kinked or damaged

and that no humidity can penetrate into them.

• In the event of a malfunction, please inform your supplier.

• Maintenance and repairs may only be carried out by authorised specialist personnel.

• The system must be isolated from the power supply before opening the housing.

•

warranty claim.

• Connection cables should always be exchanged through Videor E. Hartig GmbH.

• Use only original spare parts and accessories from Videor E. Hartig GmbH.

• The housing should only be cleaned using a mild domestic cleaning agent. Never use solvents or petrol as

these can permanently damage the surface.

• During installation, it is essential to ensure that the seals provided are correctly installed and that they are

not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.

• The installer is responsible for the maintenance of the enclosure as per the technical data, e.g. by sealing

the cable outlets with silicone.

•

• The devices may only be operated in the temperature range indicated in the data sheet and within the

• The camera may never be pointed directly at the Sun with the aperture open (this will destroy the sensor).

• It is unavoidable that during manufacture and to a certain extent during later use, humidity will be present

may condense inside the housing.

• To avoid this condensation inside the very tightly sealed housing, the manufacturer has inserted silica gel

sachets in the housing of the various camera types.

• It is however a physical given, that these silica gel bags will reach saturation after a certain amount of time.

They should therefore be replaced with new silica gel sachets.

• During installation, it is essential to ensure that the seals provided are correctly installed and that they are

not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.

• A multipolar, easily accessible isolation device should be installed in the proximity of the IR Spotlight, in

order to disconnect the device from the power supply for service work.

• The earth connection must be made according to the low impedance requirement of DIN VDE 0100.

• Subsequent painting of the equipment surface can impair the function.

• Any warranty claim is invalidated by subsequent painting.

• A safety margin of > 1m from the spotlight must be maintained when viewing directly into the IR Spotlight

in a darkened environment.

• Do not look directly at invisible LED radiation using optical instruments (e.g. a reading glass, magnifying

glass or microscope), since this can endanger the eyes, LED Class 1M.

• Operation of the IR spotlight with a defective cover or during repair is prohibited.

Class A device note

This is a Class A device. This device can cause malfunctions in the living area; in such an event, the operator may

need to take appropriate measures to compensate for these.

WEEE (Waste Electronical & Electronic Equipment)

Correct Disposal of This Product (Applicable in the European Union and other European countries with separate

collection systems).

This marking shown on the product or its literature, indicates that it should not be disposed with

other household wastes at the end of its working life. To prevent possible harm to the environment

or human health from uncontrolled waste disposal, please separate this from other types of wastes

and recycle it responsibly to promote the sustainable reuse of material resources. Household users

should contact either the retailer where they purchased this product, or their local government

Business users should contact their supplier and check the terms and conditions of the purchase

contract. This product should not be mixed with other commercial wastes for disposal.

Graphical symbols

Please pay attention to the safety instructions, and carefully read through this instruction guide before initial

operation.

Important points of warning are marked with a caution symbol.

Important points of advice are marked with a notice symbol.

Parts supplied

• Network Camera

• Operating Instruction

• CD

• Mounting Template

• Sunshield

• Plastic Anchor: 6 x 30mm (4x)

• Mounting Screw: 4 x 35mm (4x)

• Assembly Screw: 4 x 13mm (4x)

• Torque Wrench: 3mm (1x)

• Easy Bracket

Part names

Micro SD Card Slot

Reset Button

LED Control Switch

SUNSHIELD

FRONT CASE

EASY BRACKET

BRACKET

REAR CASE

RJ-45 Connector

Installation instructions

CAUTION: The camera’s base should be attached to a structural

object, such as concrete, hard wood, wall stud or ceiling rafter

that supports the weight of the camera. If necessary use appro-

priate mounting material (e.g. anchors) instead of the material

enclosed with the camera.

1. Locate the mounting template at the installation position and drill the ceiling or

wall if needed.

The easy bracket can not be installed on the ceiling.

screws(4x35mm). Skip this step when an easy bracket is not installed.

3. Route the ethernet and power cable to the connecting place. Hook up the camera

bracket with the easy bracket as illustrated below.

4. Fix the camera bracket through using assembly screws (4x13mm).

5. Set the camera’s viewing angle.

6. Put the sunshield to the camera unit.

Torque Wrench

Assembly Screw: 4x13mm

Mounting Screw : 4x35mm

Cable exit

CAUTION:

Extreme care should be taken NOT to scratch the window in front

of lens.

Care should be taken the cable is NOT to be damaged, kinked or

exposed in the hazardous area.

Do not expose the camera directly to a strong light source such

as the sun or spot light.

Pan & Tilt adjustments

• Unlock the screw on the camera bracket through using the torque wrench supplied

• Set the camera’s viewing angle then lock the screw on the bracket.

Adjustment of viewing angle with a bracket

1. Pan limit: Pan is limited to +/- 80°.

80° 80°

160°

90°

2. Tilt limit: Tilt is limited to 0° min ~ 90° max.

for wall(ceiling) installation respectively

with reference to the wall(ceiling) when

the inclination of camera module is 0°,

that is, the image is aligned horizontally.

±90°

3. Inclination limit (Horizontal image alignment):

Inclination limited to +/-90° max.

Torque wrench

Lock / Unlock

screw

Sunshield assembling

After all adjustments, assemble the sunsheild with the camera unit as illustrated.

1. Cover the sunsheild to the camera unit.

2. Slide foward to straight the camera front case.

3. Push down the front part of sunshield until clicking sound.

Make sure the sunshield is xed with camera.

Power supply connections

Make sure the power is removed before the installation. Camera can work with PoE

(IEEE Std. 802.3af). After all connections are nished properly, plug the network cable

into RJ-45 Ethernet Port and PoE is the unique power.

1. RJ-45 female connector is on the LAN cable from Camera.

2. Extension cable should be passed through the connector without RJ-45

connector. After then, extension cable should be assembled with RJ-45

male connector.

3. RJ-45 male connector from extension side should be plugged in. Tighten

all plugs rmly to ensure waterproof.

Camera side

Extension side

Quick Network Setup

1. After the camera is connected to the network, start ‘eneo Scan Device’ tool (en-

closed CD).

2. Use the ‘Scan eneo’

3. By default the camera is set to DHCP. If there is no DHCP server present in the net-

work the camera will fall back to a default IP address after a while. In this scenario

identical IP addresses.

The network camera‘s default IP address is: 192.168.1.10.

4. Right clicking the device name in the eneo Scan Device tool will bring up the

context menu. Use the ‘Open Device Web Site’ option to access the camera.

5. The web viewer login page will open up in your default web browser.

In case of Microsoft Internet Explorer install Active-X named VIDEOR E. Hartig

GmbH according to the instruction at the bottom of the browser.

6. Use the default user name and password to log in.

Default user name: admin

Default password: admin

Web viewer description

(A) Menu button : Click the button to show or hide the setup menu bar.

(B) Model name : Show a camera model name connected.

(D) Main setup menu bar : Set the camera or network functions.

(E) Camera monitoring window: Display the currently connected camera view or

function.

(F)

Log out and exit the web viewer

Player control & Display

(1) Pause: Freeze the current video.

(2) Snapshot: Take a picture of the video image currently on display. Supports the

origin image size view, print, and save feature.

(3)

Record: Record the current video on display.

A B

1 2 3

(4)

(5)

(6)

Full Screen: Expand the current windows into maximum monitor size. Clicking

ESC button or right button on mouse to back to the normal view.

Custom: Move the control bar to make preferred window size.

PTZ Control

Used to adjust zoom/focus manually or one-push

focus automatically.

• Zoom: Adjusts camera image zoom in/out ratio

manually.

• Focus: Adjusts camera image focus manually.

• Push AF: When Push AF command is sent, camera

becomes Auto Focus mode to adjust focus position

for a while.

Note:

• This option is activated Motorized lens / AF- Zoom

lens model only.

• Enable lens locking after completing zoom/focus

setting.

[ Setup> Video&Image> Image> AF]

• Do not adjust zoom/focus at low light condition,

night mode. It might cause erroneous focusing.

Setup Menu Table

Category Menu Conguration

LIVE VIEW

Player Control Pause, Snapshot, Record

Display (Window Fit, Full Screen, Custom)

Video Stream Stream1, Stream2, Stream3

Protocol HTTP, TCP, UDP

PTZ Contol Zoom, Focus, Push AF

PLAYBACK Event Search, Timeline Search, Timeline Bar

SETUP

Information General, System Information, Open source Information

Video & Image

Source

Image

Basic

Brightness, Contrast,

Saturation, Hue, Sharpness,

mirror image

OSD

Enable text OSD, Enable

date&time OSD, Enable

zoom&focus OSD, Mode

AWB Mode, Cb Gain, Cr Gain

Mode, Speed, Lens Locking,

Locking Timer, Lens Calibra-

tion, Enable Day&Night sync

focus

Day&Night

WDR

WDR(Mode, Level), Defog

(Mode)

BLC

BLC (Mode, Level), HLC

(Mode)

DNR

2DNR(Mode, Level),

3DNR(Mode, Level)

LDC Mode, Level, Boundary Line

VerticalView Mode, Rotation

Privacy Mask Color, Name

Digital Zoom Level

Mode, Switching time,

Threshold (D->N), Threshold

(N->D), Smart IR

Mode, Shutter, Max.shutter,

Gain, Max gain, Slow shutter,

Auto iris, Auto icker-less

Stream1/2/3, Snapshot

SETUP

Record

Overwrite when storage is full,

Continuous record setting

Schedule

Storage Format, Remove, Storage Information

Event

Triggers

Motion, VCA, Tamper, System, Manual, Network, Timer,

Day/Night

Actions Record, E-Mail, FTP, Video Boost, Notication Server

Rules Event Processing, ONVIF Mapping

System

Security User, HTTPS, IP Filter, ONVIF, Video Stream, Export/Import

Date & Time Current Time, New Time, Time Zone, Date & Time Display

Network TCP/IP, DDNS, RTP, UPnP, Zeroconf, Bonjour

Language English, German , French, Korean, Polish, Finnish

Maintenance

Maintain(Restart, Reset, Default), Upgrade, Setup Export,

Setup Import

LOG OUT

USER MANUAL

Logs & Report

Logs (Database Capacity, Search Condition, Log List),

Report

Click the Add, Edit, or Delete button for managing user account.

Quick Setup

Information

Users

group automatically and shows the permission status to access the menus.

• Name: Shows the name which registered to access the camera.

• Group: Shows the assigned permission given to users.

• Authority: Shows the permission status to access the menus.

The Information shows the camera information such as Model name, MAC address, IP

address, Zeroconf IP address, Firmware version, Server time, Running time, CPU Usage,

Incoming/Outcoming Bandwith and Open source list.

Video Stream Export/Import

Add

To add a new user:

1. Click the Add tab, and type a new user name. (1 to 14 alphanumeric characters).

User names are not case sensitive.

Passwords are case sensitive.

3. Select one of the groups you wish to assign to the user.

4. Click the OK button to save the settings and add a new user.

Edit

To edit a user:

1. Select one of the User Names in the User List you want to modify.

2. Click the Edit tab, then new pop-up window appears.

4. Select one of the groups you wish to assign to the user.

5. Click the OK button to save the settings and modify a user.

Delete

To delete a user:

1. Select one of the User Names in the User List you want to remove.

Date & Time

Current Time

Shows the current date and time.

New Time

Select one of the server time.

• Synchronize with computer time: Sets the time

according to the clock on your computer.

• Set manually: Using this option allows you to manu-

ally enter the date and time.

• Synchronize with NTP Server: This option will

obtain the correct time from an NTP server every 60

minutes. The NTP server’s IP address or host name is

Time Zone

Select the time zone where your camera is located. Click the “Automatically adjust for

daylight saving changes” checkbox to automatically update the time changes caused

by daylight saving.

Time zone: The default setting is GMT.

Day & Time Display

Select one of the Date and Time format.

• Date Format: The default setting is YYYY-MM-DD.

• Time Format: The default setting is 24 hours.

Network

assigns an IP address to the device if there is a device on the network.

Obtain IP address via DHCP :

Select the choice box if you want to assign the IP address from DHCP server automatical-

ly, and then the remaining setting are read-only text.

Use the following IP address:

Select the choice box if you want to assign the IP address manually.

IP address:

The address of the camera connected to the network. Specify an unique IP address for

this network camera.

Subnet mask:

The address that determines the IP network that the camera is connected to (relative to

its address). Specify the mask for the subnet the network camera is located on.

Gateway:

The gateway that accesses other networks. Specify the IP address of the default router

segments.

Further information

site at www.eneo-security.com to receive the latest functionality for your product.

The manual, and other software tools are available on the eneo website at www.eneo-se-

curity.com or on the included CD.

Information on compatible video management software solutions can be found in the

category Videomanagement at www.eneo-security.com.

La page charge ...

Eneo IPB-62M2812M0A Quick Installation Manual

Marque: Eneo

Modèle: IPB-62M2812M0A

Catégorie: Des caméras de sécurité

Taper: Quick Installation Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Eneo IPB-62M2812M0A
Deutsch: Eneo IPB-62M2812M0A

Eneo IPB-62M2812M0A Quick Installation Manual

Eneo IPB-62M2812M0A Quick Installation Manual

dans d''autres langues

Documents connexes