Yamaha C-5000 Le manuel du propriétaire

Owner´s Manual

Mode d´emploi

Pre-Ampliﬁer

Préampliﬁcateur

Français

English

2

Thank you and congratulations on your purchase of this Yamaha product.

¡

You can enjoy the high-quality stereo sound of this preamplier at home.

¡

This Owner’s Manual describes the unit’s features, connection procedures, and operations.

¡

To use the product properly and safely, we suggest that you read this manual and Safety Brochure

(separate booklet) thoroughly.

Keep the manual in a safe, accessible place for future reference.

You can download a PDF version of this manual from the following Yamaha website.

https://download.yamaha.com/

Features

¡

Left-right symmetrical design creates a bookmatched structure

¡

Class A operation of full-stage, full-oating balanced signal transmission from input to output

¡

Full-oating and balanced phono EQ amplier with balanced inputs

¡

High-accuracy controls that employ a proprietary bearing structure and high-rigidity lever switches

¡

Twin transformer designed specically for audio, which is completely separate from the control power

supply

¡

Stable mechanical grounding construction dramatically lessens the impact of external vibration.

¡

Tone control circuit that features a proprietary parallel volume system

¡

Newly-designed brass spiked feet

¡

Gain control function that enables ultra ne volume adjustment

About this manual

¡

The illustrations as shown in this manual are for instructional purposes only.

¡

The company names and product names in this manual are the trademarks or registered trademarks of

their respective companies.

¡

“

WARNING

” describes precautions to be followed to avoid the possibility of serious injury or

even death.

¡

“

CAUTION

” describes precautions to be followed to avoid the possibility of injury.

¡

“

NOTICE

” describes precautions to be followed to avoid the possibility of malfunction/damage to the

product, or damage to data.

¡

“

Note

” describes supplemental information about the product.

¡

Before starting to use the product, please be sure to read the separate “Safety Brochure”.

English

3

English

Table of contents

Features . . . . . . . . . . . . . . . . . . . . . . . . 2

About this manual . . . . . . . . . . . . . . . . .2

Supplied accessories . . . . . . . . . . . . . . . . 4

Maintenance . . . . . . . . . . . . . . . . . . . . . 4

Mirror-nish side panels . . . . . . . . . . . . .4

Surfaces other than the mirror-nish

side panels . . . . . . . . . . . . . . . . . . . . . 4

Part Names and Functions

Front panel . . . . . . . . . . . . . . . . . . . . . . 6

Rear panel. . . . . . . . . . . . . . . . . . . . . .10

Balanced and unbalanced connections . . 14

Remote control . . . . . . . . . . . . . . . . . . 16

Installing batteries in the remote control

. . 18

Operating the remote control . . . . . . . . 18

Connections

Connecting an external component . . . . . 20

Connecting a turntable . . . . . . . . . . . . 22

Connecting a recording component . . . . 22

Connecting another preamplier . . . . . . 23

Connecting a power amplier and

an active subwoofer . . . . . . . . . . . . . . 23

Trigger connections . . . . . . . . . . . . . . . 24

Controlling the power on-and-o operation

of a connected component, such as

a power amplier, in sync with this unit . . 24

Controlling the unit’s power on-and-

o operation in sync with a connected

component, such as an AV receiver. . . . .24

Remote connections . . . . . . . . . . . . . . . 25

Operating the unit from another room . . 25

Remote connection between Yamaha

components . . . . . . . . . . . . . . . . . . . 25

Connecting the power cord. . . . . . . . . . .26

Operations

Turning the power on . . . . . . . . . . . . . . 28

Selecting the input and output . . . . . . . . 28

Selecting the input from the EXT.IN jacks

. . 29

Adjusting the turntable input setting . . . . 29

PHONO selector . . . . . . . . . . . . . . . . . 29

Subsonic lter . . . . . . . . . . . . . . . . . . 30

Adjusting the volume level . . . . . . . . . . . 30

Lowering the volume level momentarily

. . 31

Adjusting the tone . . . . . . . . . . . . . . . . 31

Connecting headphones . . . . . . . . . . . . 32

Reference Materials

General specications . . . . . . . . . . . . . . 34

Block diagram . . . . . . . . . . . . . . . . . . . 36

Audio characteristics . . . . . . . . . . . . . . .37

Frequency response (tone control) . . . . . 37

Total harmonic distortion (PHONO). . . . .37

Frequency response (subsonic lter) . . . .38

Volume curve. . . . . . . . . . . . . . . . . . .38

Troubleshooting. . . . . . . . . . . . . . . . . .39

Index . . . . . . . . . . . . . . . . . . . . . . . . . 41

4

Supplied accessories

Please make sure that the following accessories are included in the package.

• Remote control

• Batteries (AAA, R03, UM-4) (x2)

• Power cord

• Owner’s Manual (this book)

• Safety Brochure (separate booklet)

WARNING

Do not use the supplied power cord for other devices.

Maintenance

To use this product for an extended period of time, we recommend that you maintain it regularly.

WARNING

• Check the power cord regularly to see if it is dusty. If so, wipe o the dust completely. Otherwise, re or electric shock might be

caused.

• Do not use aerosol or ammable gas spray for cleaning or lubrication. Otherwise, ammable gas will build up inside the unit,

causing possible explosion or re.

NOTICE

• Use a dry soft cloth to clean the unit. Using cleaning agents, such as benzene or thinner, detergent, or chemically-treated cloth

might cause color changes or deterioration of the surface. If the surface gets very dirty, damp a cloth with detergent (diluted

with water), wring the cloth tightly, and wipe o the dirt.

• If you wipe the surface area in the vicinity of the Yamaha logo with force, the logo might peel o or ber from the cloth might

stick to the surface.

Mirror-nish side panels

We recommend that you use a cleaning cloth such as those made for pianos. If the surface is very dirty, use a soft cloth

that is damp with water and wrung tightly.

Surfaces other than the mirror-nish side panels

Wipe other surfaces using a soft dry cloth. If the surface gets

very dirty, dampen a cloth with detergent diluted in water,

wring the cloth tightly, and then wipe the dirt from the surface.

Mirror-nish

side panels

5

English

Part Names and Functions

This section lists the names and describes the function of

various parts on the front and rear panels, and the remote control.

6

Front panel

A.

STANDBY/ON/OFF (Power)

switch/ indicator

Turns the power to the unit on (standby) or off.

STANDBY/ON

: Switches between standby and on using

the

A

AMP key on the remote control.

OFF

: Turns the power to the unit off.

Power status Indicator

On mode Lit brightly

Standby mode Lit dimly

O mode Oﬀ

The unit will enter standby mode not only when you

press the AMP key on the remote control, but also in one

of the following events:

• If the unit is powered on but not operated for eight

hours while the auto power standby function is turned

on, or

• If you turn off the power to the device that is connected

to this unit’s TRIGGER IN jack.

For more information, refer to “

Q

AUTO POWER

STANDBY switch” in the “Rear panel” section (page

13) and to “Trigger connections” (page 24).

Note

After you turn on the unit, it will take a few seconds before

the unit can reproduce sound.

NOTICE

If you plan not to use the unit for an extended period of

time, be sure to unplug the power cord from the AC outlet.

Even when the STANDBY/ON/OFF (Power) switch is turned

o (the power indicator is dark), a minimal amount of

electric current is still owing to the unit.

B.

Remote control sensor

Receives signals from the remote control. For more

information, refer to “Operating the remote control”

(page 18).

C.

PHONES jack

Connect your headphones here to listen to music

privately. For more information, refer to “Connecting

headphones” (page 32).



 





7

English

D.

TRIM selector

Switches the headphone amp gain. The unit will adjust

the volume level when headphones are plugged in to

avoid sudden changes in volume by modifying the level

balance between the audio output from the PHONES jack

and from the speakers.

Choices

: −6 dB, 0 dB, +6 dB, +12 dB

E.

GAIN selector

Switches the preamp gain. The unit will smoothly adapt to

the power amp gain and speaker sensitivity, enabling you

to make ne volume adjustments. For more information,

refer to “Adjusting the volume level” (page 30).

Choices

: −12 dB, −6 dB, 0 dB

F.

OUTPUT selector

Species which OUTPUT jacks will output signals, as

follows:

Use this selector if multiple power ampliers are

connected.

OUTPUT selector

OFF ALL BAL LINE1 LINE2

BAL

jacks

—

Output Output

— —

LINE 1

jacks

—

Output

—

Output

—

LINE 2

jacks

—

Output

— —

Output

G.

PHONO selector

Indicates the type of cartridge installed on the turntable

that is connected to the PHONO jacks on the rear panel

(

MM, MC 300, MC 100, MC 30, MC 10

). For

more information, refer to “Adjusting the turntable input

setting” (page 29).

NOTICE

Before you replace the cartridge, be sure to turn o the

power to this unit.



 





8

H.

BASS control

Adjusts the low-frequency response in the range from

−10 dB to +10 dB (in 0.5 dB steps). The center position

produces a at response.

I.

TREBLE control

Adjusts the high-frequency response in the range from

−10 dB to +10 dB (in 0.5 dB steps). The center position

produces a at response.

J.

BALANCE control

Adjusts the audio output balance between the left and

right speakers in the range from L (the right channel is

muted) to R (the left channel is muted) to compensate

for sound imbalances caused by speaker locations or

listening room conditions.

K.

EXT. DIRECT switch/indicator

If you press the EXT. DIRECT switch once, the EXT.

DIRECT indicator will light up, and the audio source

input at the EXT. IN jacks will be output at the connected

output jacks. For more information, refer to “Connecting

another preamplier” (page 23) and “Selecting the

input and output” (page 28).

If you press the EXT. DIRECT switch again or rotate

the INPUT selector, the signal specied by the INPUT

selector will become the input source, and the EXT.

DIRECT indicator will turn off.

Note

If EXT. DIRECT is selected, no signal will be output at the

LINE 2 OUT (recording) jacks nor at the PHONES jack.

Front panel

  







9

English

L.

INPUT selector/indicator

Enables you to select the input source to play back.

Options are:

PHONO, PHONO BAL, TUNER, CD, BAL 1,

BAL 2, LINE 1, and LINE 2

. The indicator for the selected

input source lights up.

Note

If LINE 2 is selected here, audio signals will not be output at

the LINE 2 OUT (recording) jacks.

M.

SUBSONIC FILTER switch

Toggles between

ON

(enabled) and

THROUGH

(disabled)

for the subsonic lter. For more information, refer to

“Adjusting the turntable input setting” (page 29).

Note

If the INPUT selector is set to any option other than PHONO

or PHONO BAL, the lter will be disabled.

N.

AUDIO MUTE switch/indicator

Press this switch to reduce the current volume level by

approximately 20 dB. The indicator will light up. Press

again to restore the audio output to the previous volume

level. The indicator will turn off.

O.

VOLUME control

Adjusts the volume level. This setting will not affect the

output level at the LINE 2 OUT (recording) jacks.

Note

The VOLUME control will not aect the volume level if EXT.

DIRECT is selected as the input source. To adjust the volume

level, use the volume control on the external preamplier

or another component connected to the EXT. IN jacks.

P.

Feet

If the unit is unstable, adjust the height of the feet as

needed by rotating them.



  







10

Note

For information regarding the connection procedure, refer

to “Connections” (page19).

A.

PHONO jacks

RCA and XLR-type jacks. If the INPUT selector is set

to PHONO, the signals at the RCA-type PHONO jacks

will be the input source. If the INPUT selector is set to

PHONO BAL, the signals at the XLR-type PHONO jacks

will be the input source.

Your preamplier comes with a shorting plug installed on

each RCA-type PHONO input jack. If you are planning

to connect an external component to these jacks, remove

the shorting plugs. For more information, refer to

“Connecting a turntable” (page 22).

PHONO

CAUTION

Handle the shorting plugs carefully. Do not allow children

to play with the shorting plug; otherwise they might

swallow it.

NOTICE

• Shorting plugs are intended for unused INPUTS ONLY;

using them on OUTPUTS can cause serious damage to

your components.

• If you are planning not to use the RCA-type PHONO input

jacks, insert the shorting plugs into the jacks to prevent

random static or noise from degrading the audio signal.

B.

SIGNAL GND (ground) terminal

If you connect your turntable to the RCA-type PHONO

input jacks, also connect the turntable to this terminal.

Doing so may reduce noise.

Rear panel



  

   

11

English

C.

BAL 1/BAL 2 jacks

These are two sets of XLR-type balanced input jacks. If

the INPUT selector is set to BAL 1 or BAL 2, signals at

the corresponding XLR jacks will be the input source.

Note

Set the ATTENUATOR selector and PHASE selector

appropriately for the playback components that are

connected to the unit.

D.

ATTENUATOR selector

Enables you to set the allowable input level for the XLR-

type balanced input jacks (BAL 1 and BAL 2 jacks). For

more information, refer to “Adjusting the volume level”

(page 30).

BYPASS

: The allowable input level will not change.

Usually select this option.

ATT. (−6 dB)

: The input gain will be lowered by 6 dB

to raise the allowable input level. Select this option if

the audio output from the connected component sounds

distorted.

E.

PHASE selector

Species the HOT pin position for the XLR-type

balanced input jacks (BAL 1 and BAL 2 jacks).

NORMAL

: Pin #2 is specied as HOT.

INV.

: Pin #3 is specied as HOT.

For more information, refer to “Balanced and unbalanced

connections” (page 14).

F.

TUNER jacks

These are RCA input jacks. If the INPUT selector is set

to TUNER, signals at these jacks will be the input source.

Connect your tuner here.



  

   

12

G.

CD jacks

These are RCA input jacks. If the INPUT selector is set

to CD, signals at these jacks will be the input source.

Connect your CD player here.

H.

LINE 1 jacks

These are RCA input jacks. If the INPUT selector is set

to LINE 1, signals at these jacks will be the input source.

I.

LINE 2 IN jacks

These are RCA input jacks. If the INPUT selector is set

to LINE 2, these jacks will be the input source.

J.

LINE 2 OUT (recording) jacks

These are RCA input jacks for recording. These jacks

normally output the input source signals selected via the

front panel or remote control. For information on the

connection procedure, refer to “Connecting a recording

component” (page 22).

Note

• Connect the LINE 2 IN jacks and LINE 2 OUT (recording)

jacks to the same component.

• The LINE 2 OUT (recording) jacks will not output any

signals if the INPUT selector is set to LINE 2 or the EXT.

DIRECT switch is pressed.

K.

EXT.IN jacks

These jacks feature XLR-type input jacks and RCA

input jacks. If the EXT. DIRECT switch is pressed,

signals at these jacks will be the input source. Connect

your preamplier here. For more information, refer to

“Connecting another preamplier” (page 23).

CAUTION

You cannot adjust the volume level of the signals input at

the EXT. IN jacks. Therefore, be sure to connect to the EXT.

IN jacks a component that features a volume control.

Rear panel



 

  







 

13

English

Note

The volume level is xed. Operating the VOLUME control or

GAIN selector on this unit will not change the volume level

of the signal from the EXT. IN jacks. Adjust the volume level

using the volume control on the component connected to

the EXT. IN jacks.

L.

BAL jacks

These are XLR-type output jacks. Connect these jacks to

the balanced input jacks on the power amplier.

M.

LINE 1/LINE 2 jacks

These are RCA output jacks. Connect these jacks to the

RCA input jacks on the power amplier.

N.

TRIGGER IN/TRIGGER OUT jacks

These are monaural mini jacks. Connect external

components that support the trigger function here.

For more information, refer to “Trigger connections”

(page 24).

O.

REMOTE IN/REMOTE OUT jacks

These are monaural mini jacks. Connect external

components that support the remote function here.

For more information, refer to “Remote connections”

(page 25).

P.

SERVICE jack

This jack is used to service the product. It is rarely used.

Q.

AUTO POWER STANDBY switch

Species whether the unit automatically enters standby

mode.

ON

: The unit enters standby mode automatically if it is

powered on but not operated for eight hours.

OFF

: The unit does not enter standby mode automatically.

R.

AC IN jack

Connect the supplied power cord here. For more

information, refer to “Connecting the power cord”

(page 26).



 

  







 

14

Balanced and unbalanced

connections

This unit features XLR-type balanced jacks and RCA-

type unbalanced input jacks.

Note

Do not use balanced and unbalanced connections between

two components simultaneously. Doing so would create a

ground loop that could generate static and noise.

Balanced connection

A balanced connection is designed to cancel and prevent

unwanted noise. Since longer cables tend to pick up

more noise, a balanced connection is useful if you need

to use long cables. Generally, if your components feature

balanced outputs, you should use balanced connections.

Jacks for balanced connections

XLR-type jacks on this unit are used for balanced

connections. The input and output jacks utilize different

designs. Input jacks are female, and output jacks are

male. For balanced connections, balanced cables with

XLR connectors are used. Connect a male connector

on the cable to a female jack on the unit, and connect a

female connector to a male jack on the unit.

3

2

1

3

Lever

XLR connector (male)XLR jack (female)

When connecting a cable to an input jack, be sure to

align the pins on the connector with the holes in the jack,

and then insert the connector into the jack until you hear

a click. To remove the cable, while pressing and holding

down the lever on the input jack on the unit, pull out the

male XLR connector from the jack.

3

1

2

3

XLR connector (female)XLR jack (male)

Lever

When connecting a cable to an output jack, be sure to

align the holes on the connector with the pins on the jack,

and then insert the connector into the jack until you hear

a click. To remove the cable, while pressing and holding

down the lever on the female XLR connector, pull it out

from the jack.

Balanced connection polarity

When making a balanced connection, you must set the

polarity correctly. Generally, pin #2 is Hot, but sometimes

pin #3 can be Hot. Refer to the owner’s manual for the

connected component to learn which pin at the output

jack is Hot.

To set the polarity for the BAL 1 and BAL 2 input jack

pins, use the PHASE selector on the rear panel.

Note

• The PHONO and EXT. IN jacks do not feature a PHASE

switch. The pin polarity of these jacks is standard and

xed.

• Pin #2 is Hot on Yamaha players.

15

English

If the PHASE selector is set to NORMAL, pin #2

becomes Hot.

XLR-type input jack

1: Ground

(earth)

3: Cold (−)

2: Hot (+)

Lever

If the PHASE selector is set to INVERTED, pin #3

becomes Hot.

XLR-type input jack

1: Ground

(earth)

3: Hot (+)

2: Cold (−)

Lever

XLR-type output jack

1: Ground

(earth)

3: Cold (−)

2: Hot (+)

Unbalanced connection

If you are connecting an audio component that features

only standard RCA jacks, use the RCA jacks on this unit

for unbalanced connections. For unbalanced connections,

unbalanced cables with RCA connectors should be used.

These jacks and connectors do not feature a male or

female design nor polarity differences.

Ring

16

Remote control

A.

Infrared signal transmitter

Outputs infrared control signals toward the unit.

B.

A

AMP key

Turns on the power to the unit or switches it to standby

mode. For more information regarding standby mode,

refer to “Front panel” (page 6).

C.

Input select keys

Enable you to select the input source to be played back.

BAL

: Selects the component connected to the XLR-type

BAL 1 or BAL 2 jacks as the input source.

PHONO

: Selects the turntable connected to the PHONO

jacks (XLR-type or RCA) as the input source. Press the

BAL key to select the source at the XLR-type jacks, or

the UNBAL key to select the source at the RCA jacks.

LINE

: Selects the component connected to the RCA-type

LINE 1 or LINE 2 jacks as the input source.

EXT. DIRECT

: Selects the component connected to the

EXT. IN jacks as the input source. If EXT. DIRECT is

selected as the input source, audio signals will not be

output at the LINE 2 OUT or PHONES jacks.

CD

: Selects the component (usually, a CD player)

connected to the RCA-type CD jacks as the input source.

TUNER

: Selects the component (usually, a tuner)

connected to the RCA-type TUNER jacks as the input

source.

Note

Audio signals of the selected input source will be output at

the LINE 2 OUT (recording) jacks. If LINE 2 is selected as the

input source, audio signals will not be output at the LINE 2

OUT (recording) jacks.

D.

Tuner control keys

Enable you to control the functions of the connected

Yamaha tuner. Use the BAND key to switch the reception

band, and the PRESET

er

keys to select a preset

station. For more information, refer to the owner’s

manual for your tuner.

Note

Some Yamaha tuner models might not support these key

functions.

AMP CD

BAL

PHONO

LINE

CD

TUNER BAND

PRESET

SOURCE LAYER

EXT.DIRECT

BALUNBAL

21

OPEN/CLOSE

VOLUME

MUTE



















17

English

E.

A

CD key

Turns on the power to a connected Yamaha CD player, or

switches it to standby mode.

F.

OPEN/CLOSE key

Opens or closes the disc tray of a connected Yamaha CD

player. For more information, refer to the owner’s manual

for your CD player.

Note

Some Yamaha CD player models might not support the

A

CD key and/or

OPEN/CLOSE key functions.

G.

CD player control keys

Enable you to control the functions of a connected

Yamaha CD player. For more information, refer to the

owner’s manual for your CD player.

(Play)

Starts playback.

(Pause)

Pauses playback. Press or to resume playback.

(Stop)

Stops playback.

/ (Skip)

Skips to the next track, or returns to the beginning of

the current track.

SOURCE key

Selects the source to be played on the Yamaha CD

player. The playback source changes each time this key

is pressed.

LAYER key

Toggles the playback layer of a hybrid super audio CD

between “Super audio CD” and “CD.”

Note

Some Yamaha CD player models might not support these

key functions.

H.

VOLUME +/− keys

Adjust the volume level.

Note

The VOLUME +/− keys on the remote control will not aect

the volume level if EXT. DIRECT is selected as the input

source. To adjust the volume level, use the volume control

on the external amplier connected to the EXT. IN jacks.

I.

MUTE key

Reduces the current volume level by approximately

20 dB. Press the key again to restore the audio output to

the previous volume level. Pressing the VOLUME + or

− key on the remote control will also cancel muting.

18

Installing batteries in the remote

control

1

Remove the battery compartment cover.

2

Insert two batteries (AAA, R03, UM-4)

according to the polarity markings

(+ and −) on the inside of the battery

compartment.

1

2

3

Reinstall the battery compartment cover.

3

WARNING

• Do not toss the batteries into an open re, or expose

them to high temperatures, such as direct sunlight or

open ame. Otherwise, the battery might explode,

causing re or injury.

• Do not try to recharge non-rechargeable batteries.

Otherwise, batteries might explode or leak, causing

blindness, chemical burns or injury.

• If a battery is leaking, do not touch the liquid. Otherwise,

blindness or chemical burns might be caused. If your

eyes, mouth, or skin comes in contact with the liquid,

immediately wash the site thoroughly with water and

seek medical attention.

CAUTION

• Do not use a new and old batteries at the same time.

Otherwise, re, burns, or irritation due to leaking battery

liquid might be caused.

• Do not use two dierent types of batteries at the same

time. For example, if you use an alkaline battery and

a manganese battery together, or two batteries from

two dierent manufacturers or with dierent product

numbers at the same time, re, burns, or skin irritation

due to leaking battery liquid might be caused.

• Keep the batteries out of the reach of children.

Otherwise, a child might swallow the battery by accident.

Also, leaking battery liquid might cause skin irritation.

• Insert the two batteries according to the polarity

markings (+ and −). Otherwise, re, burns, or skin

irritation due to leaking battery liquid might be caused.

• If you plan not to use the remote control for an

extended period of time, or if the batteries are

exhausted completely, remove them from the remote

control. Otherwise, all batteries will eventually become

exhausted and might leak, causing skin irritation or

damage to the remote control.

Operating the remote control

To operate the remote control, aim it directly at the

remote control sensor on the front panel of the unit.

Remote control

sensor

30 30

Within 6 m (20 ft)

19

English

Connections

CAUTION

Turn o the power to all components before making any connections.

NOTICE

• Do not use balanced and unbalanced connections between two components simultaneously. Doing so would create a ground

loop that could generate static and noise.

• If you are planning to connect external components, read and follow the instruction manuals for those components.

Otherwise, this unit or external components might malfunction.

This section explains how to connect the unit to an audio source,

such as a tuner or CD player, and a power amplier.

20

Connecting an external component

Turntable

Network audio player

CD player

Hard disk recorder,

etc.

Tuner

CD playerTurntable BD player

La page charge ...

Yamaha C-5000 Le manuel du propriétaire

Yamaha C-5000 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents