Smeg LBI147 VASKEMASKIN Manuel utilisateur

LAVATRICE

WASHING MACHINE

LAVE-LINGE

WASCHVOLLAUTOMAT

LAVADORA

LIBRETTO ISTRUZIONI IT

INSTRUCTION MANUAL EN

MANUEL D'INSTRUCTIONS FR

GEBRAUCHSANLEITUNG DE

MANUAL DE INSTRUCCIONES ES

1

EN

Contents

1. PRECAUTIONS FOR SAFETY AND USE ................................................................................... 2

3. DESCRIPTION OF CONTROLS ................................................................................................. 12

4. USING THE APPLIANCE FOR WASHING ............................................................................... 13

5. CLEANING AND MAINTENANCE ........................................................................................ 21

6. TROUBLESHOOTING ................................................................................................................. 24

7. ADDITIONAL INFORMATION FOR THE USER .................................................................... 26

This appliance is tagged in accordance with European Directive 2002/96/EC on

Waste Electrical and Electronic Equipment - WEEE.

This directive contains the regulations governing the collection and recycling of de-

commissioned appliances throughout the European Union.

The symbol of the rubbish bin with a line through it on the appliance or its packag-

ing indicates that the product must be disposed of separately from other waste at

the end of its life cycle. The user is thus obliged to consign scrapped appliances to

the special electronic and electrotechnical waste disposal centres, or return them to

the dealer on purchase of a similar new appliance, on a one-to-one basis.

Consignment to the appropriate facility for environmentally responsible recycling,

treatment and disposal helps to prevent any negative effects on the environment

and health, and encourages the reuse and/or recycling of the appliance’s compo-

nent materials.

Illegal dumping of the appliance by the user will be subject to prosecution under the

relevant law.

EN

2

READ THE INSTRUCTIONS

ATTENTION!

You are advised to read all the instructions in this manual carefully; it will in-

form you

about the right conditions for the proper, safe use of your washing

machine.

It is very important to keep this instruction manual with the appliance for fu-

ture reference.

In the even

t of sale or transfer, ensure that the manual always accompanies

the appliance, to provide the necessary information about its use.

1. PRECAUTIONS FOR SAFETY AND USE

ATTENTION!

These precautions are detailed for reasons of safety.

This section must be read carefully before installation and use.

Disposing of packaging

 Never leave packaging residues unattended in the home. Separate waste

packaging materials by type and consign them to the nearest recycling cen-

tre.

 Packaging materials (plastic bags, polystyrene, etc.) must not be left within

reach of children.

Disposing of old appliances

 Once no longer in use, the appliance must be rendered unusable:

permanently disarm the lock on the door (this will prevent children

risking their lives by locking themselves inside during play) and cut

the power supply lead after removing the plug from the socket.

The appliance must be delivered to a recycling facility.

Environmental protection

 Use the whole of the maximum recommended capacity. Never exceed the

maximum permitted load.

 Do not use the prewash function for lightly or normally soiled items.

 Follow the manufacturer's recommendations on detergent usage.

 Use the highest spin speed permitted for the fabric type. Fast spins reduce

the drying time and thus energy consumption.

 Programs that work with lower temperatures are the most efficient in

terms of energy consumption. We therefore recommend that you to make a

note of the information on the labels on the items to be washed and provided

by the manufacturer. This will mean that the temperatures and detergent

doses will be optimized to avoid excessive energy consumption"

 It is recommended to follow the instructions provided in the manual, and

those provided by the manufacturers of the detergents, softeners and addi-

tives (solvents, degreasers, stain remover additives…) for their correct use

and dosage. Failure to comply with the recommendations provided may

damage the appliance.

EN

3

 Information on household detergents, additives and cleaning agents can

be found on the following website www.cleanright.eu.

 WARNING: the higher the spin speed, the higher will be the noise and

the lower the remaining moisture content. The lower the amount of residual

moisture at the end of the wash, the lower the energy consumption will be

during drying."

Safety instructions

 This appliance is intended for domestic use and is compliant with Directives

72/23/EEC and 89/336/EEC (including Directives 92/31/EEC and

93/68/EEC) currently in force.

 Read all the instructions in this manual carefully before installation and use.

 Check that the drum assembly has been released before use (see instruc-

tions). Failure to release the drum assembly may cause damage to the

washing machine and the surrounding furniture or appliances during the

spin cycle.

 This Instruction Manual is an integral part of the appliance: it must always

be kept intact with the appliance. Installation must be carried out by quali-

fied staff in compliance with the relevant regulations. The appliance is built

to provide the following functions: washing and drying of clothes or fabrics

stated to be suitable for machine washing by the producer on the relevant

label. All other uses are to be considered improper. The manufacturer de-

clines all liability for uses other than those stated above.

 The nameplate with the technical data, serial number and mark is in a visi-

ble position in the part in view after the door has been opened. The name-

plate must never be removed.

 The electrical and plumbing works required to install the appliance

must only be carried out by skilled staff.

 The appliance must be connected to earth in compliance with electrical sys-

tem safety regulations. The manufacturer declines all liability for direct

or indirect injury or damage deriving from a non-existent or defective

earth connection.

 In the event that the appliance is not connected by means of a plug, an om-

nipolar circuit-breaker device with contact gap of at least 3 mm must be

provided.

 The plug to be connected to the power supply lead and the relative socket

must be of the same type and comply with the relevant regulations. Check

that the mains voltage and frequency are the same as the values marked

on the nameplate. The use of adapters or junctions is not recommended.

Never disconnect the plug by pulling on the power supply lead.

 The appliance is only disconnected from the electricity supply if the

plug has been removed from the socket or the electrical system mas-

ter switch has been turned off. The power plug must be accessible af-

ter the appliance has been installed.

 The appliance must be installed using new sets of hoses (supplied with the

appliance). Old hose sets should not be reused.

 Take care that the appliance is not standing on the power supply cable.

EN

4

 The washing machine must never be used on vehicles, on board ships or

planes, or in environments with hazards, such as explosive or corrosive en-

vironments (powders, vapours and gases) or explosive and/or corrosive liq-

uids.

 Do not install the washing machine in places with a risk of frost. Frozen

pipes may burst under the pressure.

 Make sure that the drain hose connected to the sink is securely fastened

and cannot move.

 If it is not fixed in place, the repulsive force of the water might thrust it away

from the sink, causing the risk of flooding.

 When connecting the hose to a sink also check that the water drains

from it quickly, as otherwise the sink may overflow.

 Do not overload the appliance.

 Never use detergents which contain solvents or chemicals for washing in

the washing machine. They might damage the appliance and form poi-

sonous vapours. These fumes might also catch fire and explode.

 Garments soaked in petroleum products must not be washed in the wash-

ing machine. Before washing, check that garments do not contain inflam-

mable devices (e.g. cigarette-lighters, matches, etc.)

 If volatile cleaning fluids are used, ensure that these substances have been

removed from the garments before they are placed in the appliance.

 Before loading garments for washing, check that the pockets are empty,

buttons secure and zips fastened.

 Do not wash frayed or torn garments.

 During washing at high temperatures, the glass in the door will become very

hot.

 Check that all water has been drained from the appliance before open-

ing the door.

 If there is water inside, pump it out before opening the door. If in doubt,

read the instruction manual.

 The water in the appliance is not suitable for drinking!

 Swallowing washing machine detergents may injure the mouth and throat.

 Before removing the garments from the washing machine check that the

drum is at a standstill.

 Switch the appliance off after each use to avoid wasting electricity.

 Leave the door ajar between washes to keep the gasket in good condition.

 In the event of a malfunction never attempt to repair the appliance your-

self. Disconnect the appliance from the electricity supply and turn off the

water tap. Then contact a qualified engineer. Repairs must only be car-

ried out by qualified staff.

 The appliance is intended for use by adults. Do not allow children to

tamper with the washing machine's controls or play with it and do not keep

children in the vicinity while the programme is in progress.

 Young animals or small children might climb into the washing machine.

 Always check the inside of the drum before use and do not allow children

to play with the appliance.

EN

5

 Keep children away from the appliance when the door or the detergent

drawer is open; the appliance might contain detergent resides which may

cause permanent injury to the eyes, mouth and throat, or even cause death

by suffocation.

 The appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their safety.

 Do not store flammable fluids near the appliance.

Length periods out of use.

 If the appliance is not to be used for a lengthy period it should be discon-

nected from the electricity and water supplies and the door should be left

ajar to prevent unpleasant smells from building up inside.

For Great Britain only

WARNING: this appliance must be earthed.

Fuse replacement

If the mains lead of this appliance is fit-

ted with a BS 1363A 13amp fused

plug, to change a fuse in this type of

plug use an A.S.T.A. approved fuse to

BS 1362 type and proceed as follows:

1. Remove the fuse cover (A) and

fuse (B)

2. Fit replacement 13A fuse into

fuse cover

3. Refit both into plug

Important:

The fuse cover must be refitted when changing a fuse and if the fuse cover is

lost the plug must not be used until a correct replacement is fitted.

Correct replacement are identified by the colour insert or the colour embossed

in words on the base of the plug.Replacement fuse covers are available from

your local electrical store.

EN

6

If the appliance is provided with a plugless supply cord:

 It is necessary to install in the fixed wiring an all-pole disconnection de-

vice having a gap between contacts of at least 3,5mm. After installation

the disconnection device has to be easy to reach.

 The connection to the mains must be carried out by a qualified technician

in accordance to the scheme shown below and the regulations in force

L = brown

N = blue

= yellow-green

 In the event of damage to the supply cord, it has to be replaced by the

manufacturer or an authorized technical service center in order to avoid

any risk.

Important!

This appliance is easy to use.

However, for the best results it is important to read this manual carefully and

follow all the instructions before putting it into operation.

The manual provides the correct instructions for installation, use and mainte-

nance, as well as giving useful advice.

The manufacturer declines all responsibility for injury or damage cau

sed

by failure to comply

with the above regulations or deriving from tampering

with even just one part of the appliance and the use of non-

original spare

parts.

EN

7

2. INSTALLATION INSTRUCTIONS

Important!

The appliance must be installed by a qualified engineer in compliance

with the relevant regulations.

The washing machine is heavy. Take care when lifting it.

2.1 UNPACKING

The unit on flexible mounts is fixed in place for transport using the screws (A)

on the rear of the washing machine with the relative plastic spacers (B). Once

the screws have been removed, the power supply lead can be used.

1. Undo all the screws with a 10 mm spanner.

2. Remove all the screws (A) from the rear

3. Remove all the plastic spacers (B)

4. Fit all the plastic plugs (C) provided, to pre-

vent water splashes from getting into the appli-

ance, and contact with live parts.

Warning!

 Do not turn the appliance upside-down or place it on its sides.

 All the transport retainer fittings should be kept in a safe place; they must be

fitted again if the appliance has to be moved around in the future.

A+B

A

B

C

EN

8

2.2 POSITIONING AND LEVELLING

1. Place the appli-

ance in the chosen

position.

2. Level the appli-

ance carefully in all

directions with the

aid of a spirit level,

adjusting the height

of the feet if neces-

sary. Once done, fix

the feet in place with the locknuts provided.

3. On appliances with adjustable rear feet, note that the rear of the appliance

rests on skids and not on the feet. Before inserting the appliance into its

place between the kitchen units, check that the rear feet are screwed fully in

to prevent damage as the appliance is shifted into position.

Once the appliance is in position in the kitchen, the height of the rear feet

has to be increased so that the appliance no longer stands on the skids. Af-

ter adjusting the rear feet, level the appliance and fix the front feet at the

height required.

EN

9

The water intake and drain hoses can be fitted pointing to the left or right for ef-

fective installation.

Warning!

 This operation must be carried out with care to prevent the washing

machine from vibrating, moving or generating excessive noise during

use.

 If the appliance is installed on a carpeted floor, take care to ensure

that the openings in the bottom of the washing machine are not ob-

structed.

 Also check that during operation the washing machine is not resting against

walls, kitchen units, etc.

 The appliance must not be installed behind a door with lock, a sliding door,

or a door with hinge on the opposite side.

EN

10

2.3 CONNECTING TO THE WATER SUPPLY

1. Check that the water supply pressure is in the following

range: 0,05-0,9MPa. With higher pressures, use a pressure

reducer.

2. Connect the cold water supply hose (blue screw collar)

to the cold water tap with ¾ gas threaded connector, taking

care to tighten firmly to prevent leaks. The water sup-

ply hose must not be kinked or crushed and must not

be changed or cut. Threaded connections must only

be tightened by hand.

3. When appliances are supplied with hot water, the intake water tempera-

ture must not exceed 60°C and the hose with red screw collar must be con-

nected to the hot water supply tap.

Warning!

 If the connection is made to new pipelines, or lines which have been out

of use for a long time, allow a considerable amount of water to flow out be-

fore connecting the intake hose. This prevents any sand or other dirt from

fouling the filters installed in the appliance to protect the water intake

valves.

 The new intake hose supplied with the appliance must be used, and the old

water supply hose must not be used.

2.4 CONNECTING TO THE DRAIN

1. Insert the end of the drain hose into a drain pipe having inside diameter of

at least 4 cm, at least 50 to 90 cm above floor level, or connect it securely

(using the plastic fitting on the elbow in the hose) to a sink or bathtub.

2. In all cases, check that the end of the drain hose is securely fixed to pre-

vent the repulsive force of the water from pushing it out of place.

Warning!

 Avoid kinks or restrictions to ensure effective drainage.

 Any drain hose extensions must be no more than 1 metre long, must be of

the same diameter and must be free from restrictions of all kinds.

 The end of the drain hose must never be submerged in water.

EN

11

2.5 ELECTRICAL CONNECTION

Before connecting the plug to the power socket ensure that:

1. The electrical system voltage is the same as that stated on the name-

plate on the front of the appliance, in the zone visible when the door is

open. The rated power supply and the fuses required are specified on

the nameplate.

2. The meter, safety breakers, power supply line and power socket are rat-

ed to withstand the maximum load required, stated on the nameplate.

3. The power supply socket and the plug fitted to the appliance are com-

patible without the use of reductions, multiple sockets, adapters and ex-

tension leads which might cause overheating or scorching.

If the power supply socket is not compatible with the plug supplied, re-

place the socket with one of the appropriate type.

Warning

 The power plug must be accessible after the appliance has been installed.

 It is absolutely essential to connect the appliance to earth. Connect

the plug to a socket with an earth connection in good working order.

The manufacturer declines all liability for direct or indirect injury or dam-

age deriving from a non-existent or defective earth connection. Correct

electrical connection guarantees conditions of maximum safety.

 This appliance is compliant with the requirements of EEC directive 89/336

of 3.5.89 (including the amendment directive 92/31/EEC) concerning the

elimination of radio-frequency disturbance.

 If the power supply lead is damaged, it must only be replaced with an orig-

inal spare, available from the After-Sales Service.

 Do not connection/disconnect the power supply plug from the socket

with wet hands

 Only disconnect the power supply plug from the socket by taking

hold of the plug itself, never by pulling on the lead.

EN

12

3. DESCRIPTION OF CONTROLS

3.1 CONTROL PANEL

All the appliance's control and monitoring devices are placed together on the front panel.

Programme Selector

For switching the washing ma-

chine on and off and selecting

programmes. Can be turned in

either direction. Does not turn

while programmes are in pro-

gress.

Start/Pause button:

For starting and stopping

working cycles.

Display: shows the settings (spin speed, cycle status, flexi time, child lock on/off, maximum rec-

ommended weight). The settings can be modified using the buttons underneath.

Buttons (from left to right):

Temperature selection

Spin speed selection

Option selection

Confirm option

Delay Timer

Child Lock

EN

13

4. USING THE APPLIANCE FOR WASHING

4.1 PREPARING THE ITEMS FOR WASHING

1. Subdivide the items for washing by fabric type and colour fastness.

2. Wash white and coloured items separately. New coloured items should be washed separately the

first time. Normally, items carry labels with washing instructions. The following is a short descrip-

tion of the symbols used on these labels.

Warning!

 Do not wash unhemmed or torn items as they may fray.

 Unrelated items in the wash may damage the garments or parts of the washing machine. So:

empty pockets and turn them inside-out, and remove wheels from curtains or wrap them in a mesh

bag.

 Wash very small items (belts, handkerchiefs, socks, padded bras, etc.) in a white canvas bag.

Fasten press-studs and zips and sew on loose buttons.

 The use of modern detergents and the correct washing temperature is generally sufficient to re-

move stains from fabrics. However, some difficult stains such as grass, fruit, egg, blood, rust, ball-

point pen, etc. should be dealt with before washing. Depending on the type of fabric, there are a

large number of commercial stain removers on the market. In all cases, stains should be

cleaned or diluted at once, since the older they are, the harder they are to remove.

 Failure to comply with washing guidance symbols may result in damage to the items

washed.

Wool – Only wool marked as pure new wool, with the mark, or labelled "shrink-proof, machine-

washable" can be washed in a washing machine on the specific programme; other types of wool

should be hand-washed or dry-cleaned.

WASHING

BLEACHING

Machine wash at

max. 90°C

Bleaching allowed

Do not bleach

Machine wash at

max. 60°C

IRONING

Machine wash at

max. 40°C

Hot iron

Warm iron

Cool iron

Do not iron

Machine wash at

max. 30°C

DRY CLEANING

Machine wash,

delicate cycle at

max. 60°C

Any solvent

Any solvent ex-

cept trichloroe-

thylene

Petroleum

solvent and

R113

Do not dry

clean

Machine wash,

delicate cycle at

max. 40°C

Machine wash,

delicate cycle at

max. 30°C

DRYING

Hand wash

High tempe-

rature

Less than 60°C

Do not

tumble dry

Do not wash

EN

14

4.2 OPENING THE DOOR

The appliance is fitted with a safety device which prevents the door from being opened while the pro-

gramme is in progress.

1. Check that all the water has been drained from the tank and the drum is at a standstill.

Warning!

 If the washing programme is interrupted, it will be from 3 to 15 minutes before the door can be

opened, depending on the temperature reached inside the appliance.

Warning!

The water may still be boiling hot if the wash was at high temperature.

Do not open the door if there is still water in the drum!

4.3 LOADS OF WASHING

As far as possible, to save electricity, it is more economical to wash complete loads of the vari-

ous types of fabric. Shake out the washing before loading, and alternate large and small items. It is

best to weight the load the first few times, after which you will be able to rely on your experience. As a

guide, the following is a list of the average weights of the standard items:

4.4 LOADING THE ITEMS FOR WASHING

1. Open the door and load the washing, distributing it evenly over the drum, with items opened

out and not bundled together; if possible, large and small items should be well mixed.

2. The washing machine covered by this manual can be loaded with up to 7kg of washing for

each wash. If this weight is exceeded, the washing results will be poor and the appliance may

malfunction.

3. To save energy it is more economical to wash full loads of the various types of fabric, fol-

lowing the guidance on quantities provided in the “Programmes Table” supplied in this manual.

4. Close the door by pressing against the frame until you hear it click shut. Take care not to trap

items of washing between the door and the rubber gasket.

Warning!

 If the door is not properly closed, a safety device prevents the washing machine from starting.

 Do not exceed the maximum load: overloading adversely affects washing results.

4.5 ADDING DETERGENT AND ADDITIVE

The internal tray comprises three compartments, marked with the symbols

prewash detergent

main wash detergent

for fabric conditioner, starch, additives, etc. (e.g. treatment products). The additives are added

to the washing tank automatically during the final rinse.

The main wash detergent compartment has a tang allowing the use of liquid detergent. To insert it, pull

it towards the front and then lower it.

EN

15

Following the recommendations in the "Programmes Table"

supplied with this manual, place the detergent and any addi-

tives in the drawer before the start of the programme.

Never fill with liquids above the maximum level marked;

otherwise the trays will empty too quickly.

Before pouring dense additives into the container, dilute with a

little water to ensure they do not clog the outlet.

Use only low-foam detergents suitable for use in a washing

machine.

The amount of detergent must be decided in relation of the hardness of the water, the type and

quantity of items loaded, and their degree of dirt.

This will provide the desired effect with optimal detergent consumption.

On detergent packs the recommended dose is indicated for 4 levels of water hardness and for loads of

4-5 kg of washing with average dirt levels.

Request information about the water's hardness from your water supply company.

Water hardness

Level of hardness French degrees fH German degrees dH

Soft Up to 15° Up to 8°

Medium 15° - 25° 8° - 14°

Hard 25° - 40° 14° - 22°

Very hard More than 40° More than 22°

4.6 POWDER DETERGENT DOSES

Laundry with normal dirt

1. Choose a programme without prewash.

2. Pour the total amount of detergent shown on the pack into the main wash compartment of the de-

tergent drawer.

Very dirty laundry

1. Choose a programme with prewash.

2. Place ¼ of the recommended amount of detergent in the prewash compartment of the detergent

drawer and ¾ of the detergent in the wash compartment.

Warning!

 If no recommended doses are provided, for delicate items in synthetic fibre use from ½ to 2/3 of

the recommended dose for washing tough cotton fabrics.

 Only neutral detergents recommended for wool should be used on the wool programme.

 Use the doses recommended by the detergent producer.

4.7 LIQUID DETERGENT DOSES

1. Pour the dose required into the measuring cap supplied with the bottle of liquid detergent and

place it in the drum, or use the main wash compartment of the detergent drawer, fitting the insert

provided.

2. The scale on the red insert is intended as an aid when deciding the dose of liquid detergent.

Warning!

 Liquid detergents can be used, at the doses recommended by the producer, only for the main

wash, i.e. in all programmes without prewash.

EN

16

4.8 DESCALERS

Descalers can be added to the prewash and main wash compartments as recommended by their pro-

ducers.

Place the detergent in the compartments first, followed by the descaler.

4.9 PROGRAMMES AND FUNCTIONS

For advice on selecting programmes in relation to the type of fabric, refer to the "Programmes

Table", supplied with this manual.

4.10 SWITCHING ON THE APPLIANCE AND SELECTING THE WASHING PROGRAMME

To switch on the appliance and select the programme, proceed as follows:

1. Turn the programmes knob in either direction. This switches on the washing machine.

2. Select the washing programme. The time left to the end of the programme and the maximum rec-

ommended weight for the selected programme alternate on the display. The symbols on the dis-

play light up to identify the information shown.

3. The default spin speed values are shown. The initial settings can be modified using the button un-

derneath the sequence of spin speeds. And temperatures

4. If spin speed is set, there will be no spin cycle and the appliance will stop with the tank full. If

this value is set the appliance does not perform the final spin and the washing programme ends

with water in the tank.

Time to en

d

Max recommended weight

Spin Speed selection

T

emperatures selection

EN

17

4.11 SELECTING AND CONFIRMING OPTIONS

1. The Option Selection button can be used to select the following options in sequence (from the

top down):

Prewash: adds a stage before the main wash, lasting about 20 minutes at a temperature of

35°C. Suitable for loads of particularly dirty items.

Intensive: the max. temperature is changed to 60°C and the washing stage is extended to in-

crease the effectiveness of the enzymes in the detergents. Suitable for delicate but dirty items.

Easy iron: produces items which are less creased and easy to iron.

Water plus: Increases the amount of water used for washing and rinses.

In alternative Extra rinse: this option adds a rinse to the selected washing programme.

Flexi Time: reduces the duration of the cycle. The symbol is completely illuminated with the in-

itial duration of the selected programme. Once the option has been selected the cycle duration

can be further reduced to an intermediate setting and a minimum setting and then returned to

the initial duration by repeated pressing of the Set button

In alternative Rapid: reduces the duration of the washing cycle. Suitable for small amounts of

laundry with only light dirt.

Buzzer: sets whether or not the buzzer will sound at the end of the cycle. The appliance

comes with the buzzer function "on".

2. To confirm the selected option, simply press the Confirm options button and the LED of the op-

tion remains on.

3. To delete an option selection, simply return to the option with the Selection button and press

the Confirm options button. To annul all the options previously selected in a single operation,

simply hold down the Confirm options button for 4 seconds.

4. The Buzzer option retains its "on" or "off" status for subsequent cycles. It is only automatically

switched to "off" if the Night Wash programme is chosen.

Option selection

Confirm option

Options

Start Pause

EN

18

4.12 TIME TO END

1. The Time to End can be pressed repeatedly to select the time after which the washing pro-

gramme will end. The time left before the end of the cycle calculates the initial duration of the

washing cycle, the settings made (temperature, spin speed and options) which may shorten or

lengthen the cycle's initial duration, and the delay time the user wishes to add before the cycle

starts.

2. After the Time to End function has been set, the symbol on the display remains on.

3. To annul the Delay Timer function, keep pressing the button repeatedly until the display shows

0.

4. The Start Pause symbol flashes on and off until the cycle starts. After the cycle starts, the

symbol remains constantly lit.

4.13 STARTING THE WASHING PROGRAMME

1. To start the washing programme after making your personal settings, press the Start Pause

button.

2. Once the cycle has started, the display shows the time remaining before the end of the cycle

and the Start Pause symbol on the display is constantly on.

3. During performance of the washing programme, the symbols which identify the various phases

light up:

Time to end button

Time to end symbol

Start Pause

Start pause symbol

Cycle phase symbols: Prewash, wash, rinse and final spin.

EN

19

4.14 INTERRUPTING OR CHANGING THE WASHING PROGRAMME

The washing programme in progress can be interrupted at any moment:

1. Press the “Start/Pause” button for about 3 seconds: the display shows the word PAUS (for 1

second) alternating with the time remaining until the end of the cycle (for 1 second). The

Start/Pause light flashes on and off.

Programmes can also be interrupted by turning the programme/temperature setting knob while

the cycle is in progress.

2. To change the washing programme, simply turn the programme knob to select the new pro-

gramme; there is no need to set the appliance in pause status. The new cycle will be carried

out completely, beginning from the start. If the tank had already been filled with water during

the previous cycle, the water intake phase will be omitted from the new programme.

3. To restart the cycle, press the Start-Pause button again.

4.15 PROGRAMME END

Washing programmes are completed automatically. The word END appears on the display and the

"Time remaining" light goes out.

1. Switch the appliance off by turning the programmes knob to OFF

2. Unload the laundry from the drum.

3. Leave the door ajar to allow the interior of the washing machine to dry out.

4. Turn off the water intake tap.

If during the initial spin speed setting stage, the "no spin" mode with stop with tank full (spin

speed set as 0) was selected, at the end of the washing programme the word STOP appears on the

display, alternating with ---- (spin speed of 0) and the spin light is on.

To proceed with the pump-out and spin, press the spin selection button twice. The appliance restarts

the cycle with the pump-out and spin. To select the spin speed required, press the button until the cho-

sen speed is displayed. To pump out the water from the tank without performing the spin, press the

spin selection button until the display indicates speed of 0: the pump-out will be run without spin.

4.16 CHILD LOCK

1. When this function is activated, the modification of options, temperatures, spin speed and the

washing/drying cycle is not possible while the cycle is in progress.

2. To activate the Child Lock Function, press the Child Lock (1) button and hold it down. Also

press the Option selection (2) button within 3 seconds.

3. The Child Safety Function symbol lights up to show that the function has been activated.

4. Repeat the same procedure to deactivate the function.

Child Lock Symbol

1

2

La page charge ...

Smeg LBI147 VASKEMASKIN Manuel utilisateur

Smeg LBI147 VASKEMASKIN Manuel utilisateur

dans d''autres langues

Autres documents