Electrolux EWN148540S Manuel utilisateur

user manual

notice d'utilisation

Washing Machine

Lave-linge

EWN 148540 S

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

CONTENTS

Safety information 2

Product description 4

Control panel 5

First use 8

Personalisation 8

Daily use 8

Helpful hints and tips 12

Washing programmes 13

Care and cleaning 16

What to do if… 21

Technical data 23

Consumption values 23

Installation 24

Electrical connection 27

Environment concerns 27

Subject to change without notice

SAFETY INFORMATION

Important! Read carefully & keep for future

reference.

• The safety of Your appliance complies

with the industry standards and with legal

requirements on the safety of appliances.

However, as manufacturers, we feel it is

our duty to provide the following safety

notes.

• It is most important that this instruction

book should be retained with the appli-

ance for future reference. Should the ap-

pliance be sold or transferred to another

owner, or should you move house and

leave the appliance, always ensure that

the book is supplied with the appliance in

order that the new owner can get to

know the functioning of the appliance

and the relevant warnings.

• You MUST read them carefully before in-

stalling or using the appliance.

• Before first starting up, check the appli-

ance for any damage incurred during

transport. Never connect up a damaged

appliance . If parts are damaged, contact

your supplier.

• If the appliance is delivered in the winter

months when there are minus tempera-

tures. Store it at room temperature for 24

hours before using for the first time.

General safety

• It is dangerous to alter the specifications

or attempt to modify this product in any

way.

• During high temperature wash pro-

grammes the door glass may get hot. Do

not touch it!

• Make sure that small pets and children

do not climb into the drum. To avoid this,

please check into the drum before using.

• Any objects such as coins, safety pins,

nails, screws, stones or any other hard,

sharp material can cause extensive dam-

age and must not be placed into the ma-

chine.

• Only use the advised quantities of fabric

softener and detergent. Damage to the

fabric can ensue if you over-fill. Refer to

the manufacturer’s recommendations of

quantities.

• Wash small items such as socks, laces,

washable belts etc in a washing bag or

pillow case as it is possible for such

items to slip down between the tub and

the inner drum.

• Do not use your washing machine to

wash articles with whalebones, material

without hems or torn material.

• Always unplug the appliance and turn off

the water supply after use, cleaning and

maintenance.

• Under no circumstances should you at-

tempt to repair the machine yourself. Re-

pairs carried out by inexperienced people

may cause injury or serious malfunction-

ing. Contact your local Service Centre.

Always insist on genuine spare parts.

Installation

• This appliance is heavy. Care should be

taken when moving it.

2 electrolux

• When unpacking the appliance, check

that it is not damaged. If in doubt, do not

use it and contact the Service Centre.

• All packing and transit bolts must be re-

moved before use. Serious damage can

occur to the product and to property if

this is not adhered to. See relevant sec-

tion in the user manual.

• After having installed the appliance,

check that it is not standing on the inlet

and drain hose and the worktop is not

pressing the electrical supply cable

against the wall.

• If the machine is situated on a carpeted

floor, please adjust the feet in order to al-

low air to circulate freely under the appli-

ance.

• Always be sure, that there is no water

leakage from hoses and their connec-

tions after the installation.

• If the appliance is installed in a location

subject to frost, please read the “dangers

of freezing” chapter.

• Any plumbing work required to install this

appliance should be carried out by a

qualified plumber or competent person.

• Any electrical work required to install this

appliance should be carried out by a

qualified electrician or competent person.

Use

• This appliance is designed for domestic

use. It must not be used for purposes

other than those for which it was de-

signed.

• Only wash fabrics which are designed to

be machine washed. Follow the instruc-

tions on each garment label.

• Do not overload the appliance. See the

Washing Programme Table.

• Before washing, ensure that all pockets

are empty and buttons and zips are fas-

tened. Avoid washing frayed or torn arti-

cles and treat stains such as paint, ink,

rust, and grass before washing. Under-

wired bras must NOT be machine wash-

ed.

• Garments which have been in contact

with volatile petroleum products should

not be machine washed. If volatile clean-

ing fluids are used, care should be taken

to ensure that the fluid is removed from

the garment before placing in the ma-

chine.

• Never pull the power supply cable to re-

move the plug from the socket; always

take hold of the plug itself.

• Never use the appliance if the power

supply cable, the control panel, the work-

ing surface or the base are damaged so

that the inside of the washing machine is

accessible.

Child safety

• This appliance is not intended for use by

person (including children) with reduced

physical sensory or mental capabilities or

lack of experience and knowledge unless

they have been given supervision or in-

struction concerning use of the appliance

by a person responsible for their safety.

• Children should be supervised to ensure

that they do not play with the appliance.

• The packaging components (e.g. plastic

film, polystyrene) can be dangerous to

children - danger of suffocation! Keep

them out of children’s reach.

• Keep all detergents in a safe place out of

children’s reach.

• Make sure that children or pets do not

climb into the drum. To prevent children

and pets becoming trapped inside the

drum the machine incorporates a special

feature. To activate this device, rotate the

button (without pressing it) inside the

door clockwise until the groove is hori-

zontal. If necessary use a coin.

To disable this device and restore the

possibility of closing the door, rotate the

electrolux 3

button counterclockwise until the groove

is vertical.

PRODUCT DESCRIPTION

Your new appliance meets all modern requirements for effective treatment of laundry

with low water, energy and detergent consumption. Its new washing system allows to-

tal use of detergent and reduces water consumption so saving energy.

1 2

3

4

5

6

1 Detergent dispenser drawer

2 Control panel

3 Door opening handle

4 Rating Plate

5 Drain pump

6 Adjustable feet

4 electrolux

Detergent dispenser drawer

Compartment for detergent used for

prewash and soak phase or for stain re-

mover used during the stain action phase (if

available). The prewash and soak detergent

is added at the beginning of the wash pro-

gramme. The stain remover is added dur-

ing the stain action phase.

Compartment for powder or liquid de-

tergent used for main wash. If using liquid

detergent pour it just before starting the

programme.

Compartment for liquid additives (fabric

softener, starch).

Follow the product manufacturer’s recom-

mendations on quantities to use and do not

exceed the «MAX» mark in the detergent

dispenser drawer. Any fabric softener or

starching additives must be poured into the

compartment before starting the wash pro-

gramme.

CONTROL PANEL

Below is a picture of the control panel. It shows the programme selector dial as well as

the buttons, pilot lights and the display. These are presented by relevant numbers on

the following pages.

1 2 3 4 5 6 7 8 9

1 Programme selector dial

2

Display

3

TEMPERATURE button

4

SPIN reduction button

5 PREWASH button

6

EXTRA RINSE button

7

DELAY START button

8 START/PAUSE button

9

TIME MANAGER buttons

Programme Selector Dial

It allows you to switch the appliance on/off

and/or to select a programme.

electrolux 5

Temperature

This button allows you to increase or de-

crease the washing temperature.

Spin Reduction

By pressing this button you can change the

spin speed of the selected programme.

Prewash

By selecting this option the machine per-

forms a prewash cycle before the main

wash phase. The washing time will be pro-

longed. This option is recommended for

heavily soiled laundry.

Extra Rinse

This appliance is designed to save energy.

If it necessary to rinse the laundry using an

extra quantity of water (extra rinse), select

this option. Some additional rinses will be

performed. This option is recommended for

people who are allergic to detergents, and

in areas where the water is very soft.

Delay Start

The programme can be delayed from 30

min - 60 min - 90 min, 2 hours and then by

1 hour up to a maximum of 20 hours by

means of this button.

Start Pause

This button allows you to start or to inter-

rupt the selected programme.

Time Manager

These buttons allows you to modify the

programme duration automatically pro-

posed by the appliance.

Display

2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9

2.12 2.11 2.10

The display shows the following informa-

tion:

2.1:Temperature value

2.2: Temperature icons

, Cold .

During the washing cycle the display shows

the temperature icon animated to indicate

that the appliance has started the heating

phase of the water in the tub.

2.3: Spin value

2.4: Spin speed icons.

•

No spin

•

Rinse Hold

•

Night Cycle

During the spinning phase the spiral is ani-

mated.

No spin option eliminates all the spin pha-

ses and increases the number of rinses for

some programmes.

Rinse Hold: by selecting this option the

water of the last rinse is not emptied out to

prevent the fabrics from creasing. When the

programme has finished the display shows

flashing

, the icon 2.8 is still visual-

ized, the light of button 8 is off and the door

is locked to indicate that the water must be

emptied out. To empty out the water,

please read the paragraph «At the end of

the programme».

Night Cycle: by selecting this option, the

machine will not drain the water of the last

rinse, so as not to wrinkle the laundry. As all

spinning phases are suppressed, this

washing cycle is very noiseless and it can

be selected at night or in times with a more

economical power rate. On some pro-

grammes the rinses will be performed with

more water. When the programme has fin-

ished, the display shows flashing

,

the icon 2.8 is still visualized, the light of

button 8 is off and the door is locked to in-

dicate that the water must be emptied out.

To empty out the water, please read the

paragraph «At the end of the programme».

2.5: Option icons: Extra Rinse

or Easy

Iron

.

2.6: Delay icon

The selected delay set by pressing the rele-

vant button appears on the display for a

few seconds, then the duration of the previ-

ously selected programme is displayed. The

6 electrolux

relevant icon is lighted on. The delay time

value decreases by one unit every hour and

then, when 1 hour remains, the time de-

creases every minute.

2.7: Child safety lock

(see «Personali-

sation» chapter).

2.8: Door locked icon

After you have pressed button 8 and the

machine has started, this icon is lighted on

and only the phase running icon stays on.

When the programme has finished, three

flashing zeros (

) are displayed and

this icon disappears.

2.9:

• Duration of the selected programme

After selecting a programme, the duration

is displayed in hours and minutes (for ex-

ample

). The duration is calculated

automatically on the basis of the maxi-

mum recommended load for each type of

fabric. After the programme has started,

the time remaining is updated every mi-

nute.

•

End of programme

When the programme has finished three

flashing zeros (

) are displayed, the

icon 2.8 disappears and the door can be

opened.

• Incorrect option selection

If an option which is not compatible with

the set wash programme is selected, the

message Err is displayed at the bottom

of the display for a few seconds and the

integrated red light of button 8 start flash-

ing.

•

Alarm codes

In the event of operating problems, some

alarm codes can be displayed, for exam-

ple

(see paragraph «What to do

if...»).

•

Delay Time value

2.10: Soil degree icons

•

Intensive

•

Normal

•

Daily

•

Light

•

Quick

•

Super Quick

•

Refresh

•

Super Refresh

(see paragraph «Select Time Manager op-

tion»).

2.11: Clock icon

After the programme has started, the dura-

tion is displayed and the clock icon is ani-

mated.

2.12: Washing programme phase icons

By selecting the wash programme, the

washing programme phase icons corre-

sponding to the various phases making up

the programme are shown in the upper part

of the display. After having pressed button

8 only the icon of the running phase stays

on:

•

Prewash

(this icon lights on when the

relevant option button is selected as well)

•

Wash

•

Rinses

•

Drain

•

Spin

TABLE OF SYMBOLS

Programmes Selector dial

= Cotton = Synthetics

= Delicates

= Wool / Handwah

= Lingerie = Rinse

= Drain = Spin

= Energy Saving programme (Economy) = Blanket

= Baby = 14 minutes

= Sport Light = Cool Clean

electrolux 7

Push buttons

= Temperature

= Spin reduction

= Prewash

= Extra Rinse

= Delay Start

= Start/Pause

+/-

= Time Manger buttons

FIRST USE

• Ensure that the electrical and water

connections comply with the installa-

tion instructions.

• Remove the polystyrene block and

any material from the drum.

• Before the first wash, run a cotton

cycle at the highest temperature

without any laundry in the machine,

to remove any manufacturing residue

from the drum and tub. Pour 1/2 a

measure of detergent into the main

wash compartment and start the

machine.

PERSONALISATION

Acoustic signals

The machine is provided with an acoustic

device, which sounds in the following ca-

ses:

• at the end of the cycle

• if there is a fault.

By pressing the 5 and 6 buttons simultane-

ously for about 6 seconds, the acoustic

signal is deactivated (except if there is a

fault). By pressing these 2 buttons again,

the acoustic signal is reactivated.

Child safety lock

This device permits you to leave the appli-

ance unattended and not to worry that chil-

dren might be injured by or cause damage

to the appliance. This function remains ena-

bled also when the washing machine is not

working.

There are two different ways to set this op-

tion:

1. Before pressing button 8: it will be im-

possible to start the machine.

2. After pressing button 8: it will be impos-

sible to change any other programme or

option.

To enable or disable this option press si-

multaneously for about 6 seconds buttons

6 and 7 until on the display, the icon

ap-

pears or disappears.

DAILY USE

Load the laundry

Open the door by carefully pulling the door

handle outwards. Place the laundry in the

drum, one item at a time, shaking them out

as much as possible. Close the door.

8 electrolux

Measure out the detergent and the fab-

ric softener

Pull out the dispenser drawer until it stops.

Measure out the amount of detergent re-

quired, pour it into the main wash compart-

ment

or in the appropriate compartment

if the selected programme/option it requires

(see more details in «Detergent dispenser

drawer»).

If required, pour fabric softener into the

compartment marked

(the amount used

must not exceed the «MAX» mark in the

drawer). Close the drawer gently.

Select the required programme by

turning the programme selector dial (1)

Turn the programme selector dial to the re-

quired programme. The washing machine

will propose a temperature and automati-

cally select the maximum spin value provi-

ded for the programme you have chosen.

You can change these values by operating

the corresponding buttons. The green pilot

light of the button 8 starts to flash.

The selector dial can be turned either clock-

wise or counterclockwise. Turn to position

to reset programme/Switching the ma-

chine off.

At the end of the programme the selec-

tor dial must be turned to position

,

to switch the machine off.

Caution! If you turn the programme

selector dial to another programme

when the machine is working, the red

pilot light of button 8 will blink 3 times

and the message Err is displayed to

indicate a wrong selection. The

machine will not perform the new

selected programme.

Select the temperature by pressing

button 3

By selecting a programme, the appliance

proposes automatically a default tempera-

ture.

Press this button repeatedly to increase or

decrease the temperature, if you want your

electrolux 9

laundry to be washed at a different temper-

ature.

Reduce the spin speed by pressing

button 4

By selecting a programme, the appliance

proposes automatically the maximum spin

speed provided for that programme.

Press button 4 repeatedly to change the

spin speed, if you want your laundry to be

spun at a different speed.

Select the available options by

pressing buttons 4, 5 and 6

Depending on the programme, different

functions can be combined. These must be

selected after choosing the desired pro-

gramme and before pressing button 8.

When these buttons are pressed, the corre-

sponding icons appear on the display.

When they are pressed again, the icons

disappear. If an incorrect option is selected,

the integrated red pilot light of the button 8

flashes for 3 times and the Err message

appears on the display for a few seconds.

For the compatibility among the wash-

ing programmes and the options see

chapter «Washing Programmes».

Select the Delay Start by pressing

button 7

Before you start the programme, if you wish

to delay the start, press the button 7 re-

peatedly, to select the desired delay. The

corresponding icon 2.6 will appear on the

display in the upper part of the display.

The selected delay time value (up to 20

hours) will appear on the display a few sec-

onds, then the duration of the programme

will appear again.

You must select this option after you have

set the programme and before you press

button 8.

You can cancel or modify the delay time at

any moment, before you press button 8.

Selecting the delayed start:

1. Select the programme and the required

options.

2. Select the delay start by pressing the

button 7.

3. Press button 8:

– the machine starts its hourly count-

down.

– The programme will start after the se-

lected delay has expired.

Cancelling the delayed start after having

pressed button 8:

1. Set the washing machine to PAUSE by

pressing button 8.

2.

Press button 7 once until the symbol

’

is displayed

3. Press button 8 again to start the pro-

gramme.

Important! The selected delay can be

changed only after selecting the washing

programme again.

The Delay Start can not be selected with

DRAIN programme.

Start the programme by pressing

button 8

To start the selected programme, press the

button 8, the green pilot light of the button

8 stops blinking. The icon 2.8 appears on

the display to indicate that the appliance

starts operating and the door is locked.

To interrupt a programme which is running,

press the button 8: the green pilot light

starts to blink.

To restart the programme from the point at

which it was interrupted, press the button 8

again. If you have chosen a delayed start,

the machine will begin the countdown.

If an incorrect option is selected, the red pi-

lot light of the button 8 blinks for 3 times

the message Err is displayed for few sec-

onds.

Select the Time Manager option by

pressing buttons 9

By pressing these buttons repeatedly, the

duration of the washing cycle can be in-

creased or decreased. The icon 2.10 will

appear on the display to indicate the chos-

en degree of soil. This option is available

only with Cotton, Synthetic and Delicate

programmes.

Soil Level Icon Type of fabric

Intensive For heavy soiled

items

Normal For normal soiled

items

10 electrolux

Soil Level Icon Type of fabric

Daily For daily soiled

items

Light For slightly soiled

items

Quick For very slightly

soiled items

Super Quick

1)

For items used or

worn for a short time

Refresh

1)

2)

For refreshing items

only

Super Re-

fresh

1)

2)

For refreshing a very

few items only

1) We recommend you to reduce the load sizes (see

Washing programmes table).

2) When you select this option the relevant icon appears

just for a while and then it disappears immediately.

Altering an option or a running

programme

It is possible to change some options be-

fore the programme carries them out .

Before you make any change, you must

PAUSE the appliance by pressing the but-

ton 8 (if you wish to change the Time Man-

ager option, you must cancel the running

programme and make your selection

again).

Changing a running programme is possible

only by resetting it. Turn the programme se-

lector dial to

and then to the new pro-

gramme position. Start the new programme

by pressing the button 8 again. The wash-

ing water in the tub will be not emptied out.

Interrupting a programme

Press the button 8 to interrupt a pro-

gramme which is running, the correspond-

ing green pilot light starts blinking.

Press the button again to restart the pro-

gramme.

Cancelling a programme

Turn the selector dial to

to cancel a pro-

gramme which is running.

You can select now a new programme.

Opening the door

After the programme has started (or during

the delay time) the door is locked, if you

need to open it, set first the machine to

PAUSE by pressing the button 8.

If the icon 2.8 disappears after some mi-

nutes, the door can be opened.

If the icon 2.8 does not go off, this means

that the machine is already heating or that

the water level is too high. Do not try to

force the door!

If you cannot open the door but you need

to open it you have to switch the machine

off by turning the selector dial to

. After a

few minutes the door can be opened (pay

attention to the water level and temper-

ature!).

After closing the door, it is necessary to se-

lect the programme and options again and

to press button 8.

At the end of the programme

The machine stops automatically. Three

blinking zeros (

) appear on the dis-

play and the pilot light of button 8 goes off.

Some acoustic signals sound for a few mi-

nutes.

If a programme or an option that ends with

water left in the tub has been selected, the

icon 2.8 remains displayed to indicate that

the water must be emptied out before

opening the door.

Follow the below instructions to empty out

the water:

1.

Turn the programme selector dial to

.

2. Select the draining or spinning pro-

gramme.

3. Reduce the spin speed if needed, by

pressing the relevant button.

4. Press button 8.

At the end of the programme, the icon 2.8

disappears and the door can be opened.

Turn the programme selector dial to

to

switch the machine off.

Remove the laundry from the drum and

carefully check that the drum is empty. If

you do not intend to carry out another

wash, close the water tap. Leave the door

open to prevent the formation of mildew

and unpleasant smells.

electrolux 11

Stand by : once the programme has finish-

ed after a few minutes the energy saving

system will be enabled. The brightness of

the display is reduced. By pressing any but-

ton the appliance will come out of the ener-

gy saving status.

HELPFUL HINTS AND TIPS

Sorting out the laundry

Follow the wash code symbols on each

garment label and the manufacturer’s

washing instructions. Sort the laundry as

follows: whites, coloureds, synthetics, deli-

cates, woollens.

Before loading the laundry

Never wash whites and coloureds together.

Whites may lose their «whiteness» in the

wash.

New coloured items may run in the first

wash; they should therefore be washed

separately the first time.

Button up pillowcases, close zip fasteners,

hooks and poppers. Tie any belts or long

tapes.

Remove persistent stains before washing.

Rub particularly soiled areas with a special

detergent or detergent paste.

Treat curtains with special care. Remove

hooks or tie them up in a bag or net.

Removing stains

Stubborn stains may not be removed by

just water and detergent. It is therefore ad-

visable to treat them prior to washing.

Blood: treat fresh stains with cold water.

For dried stains, soak overnight in water

with a special detergent then rub in the

soap and water.

Oil based paint: moisten with benzine

stain remover, lay the garment on a soft

cloth and dab the stain; treat several times.

Dried grease stains: moisten with turpen-

tine, lay the garment on a soft surface and

dab the stain with the fingertips and a cot-

ton cloth.

Rust: oxalic acid dissolved in hot water or a

rust removing product used cold. Be careful

with rust stains which are not recent since

the cellulose structure will already have

been damaged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well

(whites and fast coloureds only).

Grass: soap lightly and treat with bleach

(whites and fast coloureds only).

Ball point pen and glue: moisten with

acetone

1)

, lay the garment on a soft cloth

and dab the stain.

Lipstick: moisten with acetone as above,

then treat stains with methylated spirits.

Treat any residual marks with bleach.

Red wine: soak in water and detergent,

rinse and treat with acetic or citric acid,

then rinse. Treat any residual marks with

bleach.

Ink: depending on the type of ink, moisten

the fabric first with acetone

1)

, then with

acetic acid; treat any residual marks on

white fabrics with bleach and then rinse

thoroughly.

Tar stains: first treat with stain remover,

methylated spirits or benzine, then rub with

detergent paste.

Detergents and additives

Good washing results also depend on the

choice of detergent and use of the correct

quantities to avoid waste and protect the

environment.

Although biodegradable, detergents contain

substances which, in large quantities, can

upset the delicate balance of nature.

The choice of detergent will depend on the

type of fabric (delicates, woollens, cottons,

etc.), the colour, washing temperature and

degree of soiling.

All commonly available washing machine

detergents may be used in this appliance:

• powder detergents for all types of fabric

• powder detergents for delicate fabrics

(60°C max) and woollens

• liquid detergents, preferably for low tem-

perature wash programmes (60°C max)

for all types of fabric, or special for wool-

lens only.

The detergent and any additives must be

placed in the appropriate compartments of

the dispenser drawer before starting the

wash programme.

If using liquid detergents, a programme

without prewash must be selected.

1) do not use acetone on artificial silk

12 electrolux

Your appliance incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Follow the product manufacturer’s recom-

mendations on quantities to use and do

not exceed the «MAX» mark in the de-

tergent dispenser drawer.

Quantity of detergent to be used

The type and quantity of detergent will de-

pend on the type of fabric, load size, de-

gree of soiling and hardness of the water

used.

Follow the product manufacturers’ instruc-

tions on quantities to use.

Use less detergent if:

• you are washing a small load

• the laundry is lightly soiled

• large amounts of foam form during wash-

ing.

Degrees of water hardness

Water hardness is classified in so-called

“degrees” of hardness. Information on hard-

ness of the water in your area can be ob-

tained from the relevant water supply com-

pany, or from your local authority. If the wa-

ter hardness degree is medium or high we

suggest you to add a water softener follow-

ing always the manufacturer’s instructions.

When the degree of hardness is soft, read-

just the quantity of the detergent.

WASHING PROGRAMMES

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

COTTONS and LINENS

90° - Cold

Main wash - Rinses

Maximum spin speed: 1400 rpm

Max. load 8 kg - Reduced load 4 kg

1)

White and coloured cotton (normally soiled items).

SPIN REDUCTION

NO SPIN

RINSE HOLD

NIGHT CYCLE

PREWASH

2)

EXTRA RINSE

TIME MANAGER

SYNTHETICS

60° - Cold

Main wash - Rinses

Maximum spin speed: 900 rpm

Max. load 4 kg - Reduced load 2 kg

1)

Synthetic or mixed fabrics: underwear, coloured

garments, non-shrink shirts, blouses.

SPIN REDUCTION

NO SPIN

RINSE HOLD

NIGHT CYCLE

PREWASH

2)

EXTRA RINSE

TIME MANAGER

electrolux 13

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

DELICATES

40° - Cold

Main wash - Rinses

Maximum spin speed: 700 rpm

Max. load 4 kg - Reduced load 2 kg

1)

Delicate fabrics: acrylics, viscose, polyester.

SPIN REDUCTION

NO SPIN

RINSE HOLD

NIGHT CYCLE

PREWASH

2)

EXTRA RINSE

TIME MANAGER

WOOL - HANDWASH

40° - Cold

Main wash - Rinses

Maximum spin speed: 1000 rpm

Max. load 2 kg

Washing programme for machine washable wool as

well as for hand washable woollens and delicate fab-

rics with «hand washing» care symbol. Note: A single

or bulky item may cause imbalance. If the appliance

doesn’t perform the final spin phase, add more items,

redistribute the load manually and then select the

spinning programme.

SPIN REDUCTION

NO SPIN

RINSE HOLD

NIGHT CYCLE

LINGERIE

40° - Cold

Main wash - Rinses

Maximum spin speed: 1000 rpm

Max. load 2 kg

This programme is suitable for very delicate items

such a lingerie, bras and underwear. The maximum

spin speed is automatically reduced.

SPIN REDUCTION

NO SPIN

RINSE HOLD

NIGHT CYCLE

RINSE

Rinse - Long spin

Maximum spin speed: 1400 rpm

Max. load 8 kg

With this programme it is possible to rinse and spin

cotton garments which have been washed by hand.

To intensify the rinsing action, select the option EX-

TRA RINSE. The appliance will add some additional

rinses.

SPIN REDUCTION

NO SPIN

RINSE HOLD

NIGHT CYCLE

EXTRA RINSE

DRAIN

Draining of water

Max. load 8 kg

For emptying out the water of the last rinse in pro-

grammes with the option selected, which ends with

water left in the tub.

14 electrolux

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

SPIN

Drain and long spin

Maximum spin speed: 1400 rpm

Max. load 8 kg

Separate spin for hand washed garments and after

programmes with the Rinse Hold and Night Cycle op-

tion selected. You can choose the spin speed by

pressing the relevant button to adapt it to the fabrics

to be spun.

SPIN REDUCTION

COTTONS ECONOMY

90° - 40°

Main wash - Rinses

Maximum spin speed: 1400 rpm

Max. load 8 kg

White and fast coloured cotton

This programme can be selected for slightly or nor-

mally soiled cotton items. The temperature will de-

crease and the washing time will be extended. This al-

lows to obtain a good washing efficiency so saving

energy.

SPIN REDUCTION

NO SPIN

RINSE HOLD

NIGHT CYCLE

PREWASH

2)

EXTRA RINSE

BLANKET

40° - 30°

Main wash - Rinses

Maximum spin speed: 700 rpm

Max. load 2,5 kg

Special programme for a single washable synthetic

blanket or duvet.

SPIN REDUCTION

NO SPIN

BABY

40° - Cold

Main wash - Rinses

Maximum spin speed: 700 rpm

Max. load 2 kg

Extra delicate cycle for multicoloured or special knit

baby clothes.

SPIN REDUCTION

NO SPIN

RINSE HOLD

NIGHT CYCLE

PREWASH

2)

EXTRA RINSE

14 MINUTES

30°

Main wash - Rinses

Maximum spin speed: 900 rpm

Max. load 2 kg

Short washing cycle ideal for laundry which only

needs freshening up.

SPIN REDUCTION

NO SPIN

RINSE HOLD

SPORT LIGHT

30°

Main wash - Rinses

Maximum spin speed: 900 rpm

Max. load 2,5 kg

Short programme for lightly soiled mixed fabric sports

clothes.

NO SPIN

electrolux 15

Programme

Maximum and Minimum Temperature

Cycle Description

Maximum Spin Speed

Maximum Fabrics Load

Type of Laundry

Options

Detergent

Compartment

COOL CLEAN

Cold

Main wash - Rinses

Maximum spin speed: 1200 rpm

Max. load 3 kg

Highly energy efficient cold wash programme for light-

ly soiled laundry made of cottons, synthetic or mixed

fabrics. This programme requires the use of detergent

which is already active in cold water. Hint: In case of

water inlet temperatures lower than 6°C the machine

will execute a short heating phase. The detergent

must be used with the supplied or a suitable deter-

gent dosing cap (use the amount of the detergent rec-

ommended by detergent's manufacturer).

SPIN REDUCTION

NO SPIN

RINSE HOLD

EXTRA RINSE

/ OFF

For cancelling the programme which is running or to

switch the machine off .

1) If you select the Quick or Super Quick option by pressing button 9, we recommend that you reduce the maximum

load as indicated. Full loading is possible however with somewhat reduced cleaning results. If you select the

Refresh or Super Refresh option, we recommend that you reduce the load even more.

2) If using liquid detergents, a programme without PREWASH must be selected.

CARE AND CLEANING

Warning! You must disconnect the

appliance from the electricity supply,

before you can carry out any cleaning

or maintenance work.

Descaling

The water we use normally contains lime. It

is a good idea to periodically use a water

softening powder in the machine. Do this

separately from any laundry washing, and

according to the softening powder manu-

facturer's instructions. This will help to pre-

vent the formation of lime deposits.

After each wash

Leave the door open for a while. This helps

to prevent mould and stagnant smells form-

ing inside the appliance. Keeping the door

open after a wash will also help to preserve

the door seal.

Maintenance wash

With the use of low temperature washes it

is possible to get a build up of residues in-

side the drum.

We recommend that a maintenance wash

be performed on a regular basis.

To run a maintenance wash:

• The drum should be empty of laundry.

• Select the hottest cotton wash pro-

gramme.

• Use a normal measure of detergent,

must be a powder with biological proper-

ties.

External cleaning

Clean the exterior cabinet of the appliance

with soap and water only, and then dry

thoroughly.

Important! Do not use methylated spirits,

solvents or similar products to clean the

cabinet.

Cleaning the dispenser drawer

The detergent dispenser drawer should be

cleaned regularly.

The washing powder and additive dispens-

er drawer should be cleaned regularly.

Remove the drawer by pressing the catch

downwards and by pulling it out.

16 electrolux

Flush it out under a tap, to remove any

traces of accumulated powder.

To aid cleaning, the top part of the additive

compartment should be removed. Clean all

parts with water.

Clean the chamber of dispenser drawer

with a brush.

Washing drum

Rust deposits in the drum may occur due

to rusting foreign bodies in the washing or

tap water containing iron.

Important! Do not clean the drum with

acidic descaling agents, scouring agents

containing chlorine or iron or steel wool.

1. Remove any rust deposits on the drum

with a cleaning agent for stainless steel.

2. Run a washing cycle without any wash-

ing to clean off any cleaning agent resi-

dues.

Programme: Short Cotton Programme

at maximum temperature and add ap-

prox. 1/4 measuring cup of detergent.

Door seal

Check from time to time the door seal and

eliminate eventual possible objects that

could be trapped in the fold.

electrolux 17

Drain pump

The pump should be inspected regularly

and particularly if:

• the appliance does not empty and/or

spin;

• the appliance makes an unusual noise

during draining due to objects such as

safety pins, coins etc. blocking the

pump;

• a problem with water draining is detected

(see chapter “What to do if...” for more

details).

Warning! Before opening the pump

door, switch the appliance off and

remove the mains plug from the

socket.

Proceed as follows:

1. Unplug the appliance.

2. If necessary wait until the water has

cooled down.

3. Open the pump door levering on the

groove with a coin (or with the suitable

tool, that you can find in the bag con-

taining the instruction booklet, depend-

ing on the model).

1

2

4. Place a bowl with a small edge close to

the pump to collect any spillage.

5. Pull out the emergency emptying cap

from the filter cover, using pliers.

6. When no more water comes out, un-

screw the pump cover by turning it an-

ti-clockwise, using pliers, and remove

the filter. Always keep a rag nearby to

dry up any water spillages when re-

moving the cover.

Clean the filter under a tap, to remove

any traces of fluff.

1

2

18 electrolux

7. Remove foreign bodies and fluff from

the pump seat and from the pump im-

peller.

8. Check carefully whether the pump im-

peller rotates (it rotates jerkily). If it

doesn’t rotate, please contact your

Service Centre.

9. Replace the filter into the pump by in-

serting it correctly into the special

guides. Screw the pump cover firmly by

turning it clockwise.

10. Replace the emergency emptying cap

into the filter cover and fix it firmly.

electrolux 19

11. Close the pump door.

Warning! When the appliance is in use

and depending on the programme

selected there can be hot water in the

pump. Never remove the pump cover

during a wash cycle, always wait until

the appliance has finished the cycle,

and is empty. When refitting the pump

cover , ensure it is securely re-

tightened so as to stop leaks and

young children being able to remove it.

Cleaning the water inlet filters

If you notice that the machine is taking lon-

ger to fill, check that the filter in the water

inlet hose is not blocked.

1. Turn off the water tap.

2. Unscrew the water inlet hose.

3. Clean the filter in the hose using a hard

bristle brush.

4. Screw the hose back onto the tap.

5. Unscrew the hose from the machine.

Keep a rug nearby because some water

may flow.

6. Clean the filter in the valve with a stiff

brush or with the piece of cloth.

7. Screw the hose back to the machine

and make sure the connection is tight.

8. Turn on the water tap.

Emergency emptying out

If the water is not discharged, proceed as

follows to empty out the machine:

1. pull out the plug from the power socket;

2. close the water tap;

3. if necessary, wait until the water has

cooled down;

4. open the pump door;

5. place a bowl on the floor. Remove the

emergency emptying cap from the filter.

The water should drain by gravity into

the bowl. When the bowl is full, refit the

cap into the filter. Empty the bowl. Re-

peat the procedure until water stops

flowing out;

6. clean the pump if necessary as previ-

ously described;

7. screw the pump again and close the

door.

Frost precautions

If the machine is installed in a place where

the temperature could drop below 0°C,

proceed as follows:

1. Pull out the plug from the power socket.

2. Turn off the water tap.

3. Unscrew the inlet hose.

4. Place the end of the inlet hose in a bowl

placed on the floor, open the emergen-

cy emptying cup of the filter and let wa-

ter drain out.

20 electrolux

La page est en cours de chargement...

Electrolux EWN148540S Manuel utilisateur

Electrolux EWN148540S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents