Topdon BTMOBILE PRO Manuel utilisateur

86-755-21612590

1-833-629-4832 (North America)

[email protected]

www.topdon.com

@TopdonOcial

For Services and Support

12V Wireless Battery and System Tester

USER MANUAL

BTMOBILE PRO

CONTENT

Welcome

About

Package List

Compatibility

Guide to LED Indicator

APP Installation & Setup

Operation Introduction

Battery Library

Technical Specication

Warranty

Warnings

Cautions

2

3

4

5

6

19

21

22

24

FAQ

Français

Español

Deutsch

Português

日本語

Pусский

Italiano

25

27

52

77

102

127

152

177

2

English

Welcome

About

Thank you for purchasing the TOPDON BTMobile Pro wireless battery tester. Please read and

understand this manual carefully before using this product. If any issues arise from the operation of

this product, you are welcome to contact us via [email protected] for ocial technical support.

TOPDON BTMobile Pro meets a variety of battery specications including CCA, JIS, EN, DIN,

SAE, IEC, etc., and also an eective detector to pinpoint the bad cell.

It adopts the most advanced conductivity detection technology to eectively help maximize the

performance of your 12V vehicles, giving valuable, easy-to-understand information about the

vehicle battery health, alternator’s charging, and starter's cranking conditions.

The built-in ExtraSafe protections against short circuit, reverse polarity, and over voltage allow the

tester to safely connect to any battery.

EN

3 4

Package List Guide to LED Indicator

Compatibility

1. TOPDON BTMobile Pro 2. User Manual 3. EVA Carrying Case

Please be noted that battery type and CCA values (Cold Cranking Amp) are marked on the battery

label. Please refer to it before using BTMobile Pro.

1. Regular Flooded 2. AGM Flat plate 3. AGM Spiral 4. GEL 5. EFB

NOTE: If your vehicle battery is not the battery mentioned above and you are not sure about which

type it is, please choose AGM to conduct test, and the error is within 10%.

LED Indicator Battery Status

Successful Battery Connection

Successful Bluetooth Connection

Error. Over temperature, or over voltage

EN

Green Light

Blue Light

Red Light

5 6

APP Installation & Setup Operation Introduction

Installation:

Download and install the App: search

"BTMobile Pro" in Apple Store or

Google Play.

NOTE: Compatible with iOS 10.0 /

Android 5.0 smart devices, or newer.

Set up

For the rst time, you can choose

to register with email or skip login.

But we strongly recommend the

registration for latest product news

and timely technical assistance.

Before Test:

1. Before you test a battery in a vehicle, turn o the ignition, all accessories and loads. Close all of the

vehicle’s doors and trunk lid.

2. Make sure the battery terminals are clean. Use a wire brush to clean them, if necessary.

NOTE: This tester works best if the battery connectors have been removed and the battery posts have

been cleaned. Any corrosion between the tester clamps and the battery connectors, or between the

battery connectors and the battery posts, will degrade the tester's eciency.

3. Connect the RED (+) Positive Battery Clamp to the (+) positive battery terminal, and connect the

BLACK (-) Negative Battery Clamp to the (-) negative battery terminal. Ensure that the clamps are

securely attached to the correct terminals.

4. Open the Bluetooth on mobile device or tablet.

5. Test Introduction

• BATTERY TEST: Display SOH (State of Health), SOC (State of Charge), Voltage, Test Value, Internal

Resistance, and the readable analysis results on App;

• CRANKING TEST: Analyze the actual cranking voltage and the cranking time to help you quickly gure

out the whole state of the starting system;

• CHARGING TEST: Test dierent parts of charging system, including generator, rectier, rectier diode,

and so on for a reliable charging volt value.

EN

7 8

1. Battery Test (12V Only)

1) Open the APP on your mobile device or tablet and log in.

2) Click "Connect to the BTMobile Pro", search for the matching device name.

3) Click the matching device name to connect.

Click "Battery Test" on the

home screen and click

"BATTERY TEST".

4) 5) Select battery type and click the

corresponding type.

EN

9 10

6) Select the battery

standard marked

on the battery

label, and click the

corresponding type.

7) Select the battery standard marked on the battery label, and click "OK" to conrm.

NOTE: If the battery is JIS standard, please refer to the table for value and select CCA (SAE) as

the test standard (please Google JIS to CCA).

EN

11 12

Click "Next" and wait a

few seconds for results.

9)

8)

Click "Share" to share

the results.

2. Cranking Test (12V&24V)

NOTE: The engine and all other accessory loads must be OFF during test.

2)1) Follow the steps and start vehicle.Click "CRANKING TEST".

EN

13 14

3. Charging Test (12V&24V)

NOTE: The engine must be ON during test.

1) Click "CHARGING TEST".

3) Click "OK" to get the results.

4) Click "Share" to share the results.

2) Follow the steps and start vehicle.

3) Step on the accelerator, increase the value of RPM to 2500, keep it for 5 seconds.

4) Click "OK" to get the results.

EN

15 16

5) Click "Share" to share the results. 4. System Test (12V Only)

1) Click "SYSTEM TEST" .

2) Follow the steps to complete all tests (refer to Battery Test, Cranking Test, Charging Test

for details).

EN

17 18

After completing all test, the test result report will generate automatically. Drop down to see

each test result.

3) 5.Test Report

Select "Test Report" at the upper

right corner, click "TEST REPORT".

Click the test report which you want to check.

Or you can select it and delete it.

1) 2)

EN

19 20

Battery Library

To know your battery

information, you can check

on Battery Library. Select

Battery Library on the home

screen and click "BATTERY

LIBRARY". Follow the

prompts, select your options

such as vehicle type, MAKE,

MODEL, YEAR and CC.

1)

2) Click "Next" to get the result.

EN

21 22

Technical Specication

Warnings

Warranty

Operating Voltage: 9V~30V

Working Temperature: -10°C to 45°C (14°F to 113°F)

Storage Temperature: -20°C to 75°C (-4°F to 167°F)

Clamp Line Length: 556mm (21.89 inch)

Safety Protection: Reverse Polarity Protection DO NOT place the tester near the engine or exhaust pipe to avoid damage from high temperatures.

DO NOT smoke, cause sparks, or strike matches near the battery when testing.

DO NOT remove battery clamps while testing.

DO NOT put the tester into a highly humid or dusty environment.

DO NOT disassemble the tester.

TOPDON One Year Limited Warranty

The TOPDON Company warrants to its original purchaser that TOPDON products will be free from

defects in material and workmanship for 12 months from the date of purchase (Warranty Period).

For the defects reported during the Warranty Period, TOPDON will, according to the technical

support analysis and conrmation, either repair or replace the defective part or product.

This limited warranty is void under the following conditions:

Misused, disassembled, altered or repaired by a non-TOPDON technical repair specialist.

Careless handling and violation of operation.

Notice: All information in this manual is based on the latest information available at the time of

publication and no warranty can be made for its accuracy or completeness. TOPDON reserves the

right to make changes at any time without notice.

EN

23 24

Cautions

Use this tester in accordance with these instructions, taking into account the working conditions and

the work to be performed.

Hazardous results could occur if tool is used for purposes not intended.

Before testing, make sure the battery terminals are clean. Grease and dust could result in inaccurate

test results.

Wear eye protection when working around batteries.

Check the insulation layer of the battery clamps is in good condition (no damage, bareness or

disconnection) to avoid electric shock.

Test in a well-ventilated area. Vehicle exhaust contains toxic carbon monoxide.

Keep hair, hands, and clothing as well as tester leads and cords away from moving blades and belts.

Keep the tester out of the reach of children.

FCC Warnings:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

EN

25 26

FAQ

Q: Can BTMOBILE PRO test the battery installed in the vehicle?

A: Yes, it supports in-vehicle and out-of-vehicle testing.

Q: Is the test result accurate?

A: Yes. Our BTMOBILE PRO features advanced conductance detection giving you accurate test

results in seconds.

Q: What batteries can BTMOBILE PRO work on?

A: It works on 12V regular ooded, AGM Flat plate, AGM Spiral, GEL and Deep Cycle batteries,

with CCA between 100 to 2000.

Q:Is BTMOBILE PRO designed with any built-in protections?

A:Yes. It oers peace of mind with extra-safe Reverse Polarity and Sparkproof protection, and

easy operations even if you’re new to battery testing.

Q: How do I conrm if my vehicle battery is bad or good?

A: The battery tester will display SOH (State of Health), SOC (State of Charge), CCA (Cold

Cranking Ampere), Voltage, Internal Resistance, and Rating, with an intuitive test result of “GOOD”

or “BAD” for your reference.If the internal resistance is too large, it indicates a broken battery.

Q: Can this battery tester estimate the remaining capacity of my battery?

A: Yes.The battery tester will display SOC (State of Charge) to express as a percentage of your

battery’s rated capacity, a measure of its condition to assess the potential energy.

Note that a decent SOC (State of Charge) doesn’t mean the battery is in good condition. You need

to refer to your battery’s actual CCA Value and Internal Resistance for further analysis.

EN

28

Français

Bienvenue

À propos de

Nous vous remercions d’avoir acheté le Testeur de Batterie sans l TOPDON BTMobile Pro. Veuillez

prendre le temps de lire et de comprendre ce Manuel de l’Utilisateur avant de faire fonctionner ce

produit. En cas de problème lors de l’utilisation, veuillez contacter [email protected] pour obtenir

un soutien technique ociel.

TOPDON BTMobile Pro est capable de répondre à une grande variété de tests de spécications

de batteries tels que CCA, JIS, EN, DIN, SAE et IEC, et est également un testeur de batteries

ecace pour détecter les batteries en mauvais état.

Tout en appliquant la technologie de test de conductance la plus avancée, il peut maximiser

ecacement les performances de votre véhicule 12V et fournir aux techniciens et aux

professionnels des informations cruciales sur l’état de santé de la batterie. La fonction de test du

système du produit permet d’identier rapidement et facilement les problèmes tels que l’état de la

batterie, sa décharge et sa charge.

La protection ExtraSafe intégrée contre les courts-circuits, la polarité inverse et les surtensions

permet au testeur de connecter en toute sécurité à n’importe quelle batterie.

FR

29 30

Liste du Paquet Guide d’utilisation de l’indicateur LED

Compatibilité

1. TOPDON BTMobile Pro 2. Manuel de l’Utilisateur 3. Sac EVA

Veuillez noter que le type de batterie et la valeur de CCA (courant de démarrage à froid) sont

indiqués sur l’étiquette de la batterie. Veuillez vous y référer avant d’utiliser BTMobile Pro.

1. Inondations régulières 2. Plaque à plat AGM 3. AGM Spiral 4. GEL 5. EFB

Remarque : Si le type de votre batterie de véhicule n’appartient à aucun des éléments ci-dessus

ou si vous n’êtes pas sûr du type de batterie, il est recommandé de sélectionner le type AGM par

défaut pour le test. Comme ça, l’erreur de résultat serait inférieure à 10%. Indicateur LED État de la batterie

La batterie est connectée avec succès

La connexion Bluetooth est réussie

Erreur. Température trop élevée ou tension trop élevée

FR

Feu vert

Feu bleu

Feu rouge

31 32

Installation et mise en place de l’application Introduction d’Opération

Installation :

Téléchargez et installez l’application:

recherchez « BTMobile Pro » dans l’Apple

Store ou Google Play.

Remarque : compatible avec les

appareils intelligents d’iOS 10.0 / Android

5.0 et versions ultérieures.

Mise en place

La première fois que vous vous

connectez, vous pouvez choisir de vous

enregistrer par e-mail ou de sauter la

connexion. Mais nous recommandons

vivement de vous enregistrer pour obtenir

les dernières nouvelles sur les produits et

une assistance technique en temps utile.

Avant les tests

1.Avant de tester la batterie dans le véhicule, coupez le contact, tous les accessoires et charges. Fermez

toutes les portes et les couvercles de core.

2.Assurez-vous que les bornes de la batterie sont propres. Si nécessaire, utilisez une brosse métallique

pour les nettoyer. Remarque : si le connecteur de la batterie a été retiré et que la colonne de la batterie a

été nettoyée, le test eectué par ce testeur est le plus précis. Toute corrosion entre la pince du testeur et

le connecteur de la batterie, ou la corrosion entre le connecteur de la batterie et la colonne de la batterie,

réduira l’ecacité du testeur.

3.La « pince de batterie positive ROUGE(+) » est connectée à l’électrode positive (+) de la batterie et la «

pince de batterie négative NOIR (-)» est connectée à l’électrode négative (-) de la batterie. Assurez-vous

que la pince est reliée en toute sécurité à la borne appropriée.

4. Activez Bluetooth sur un appareil mobile ou une tablette.

5. Présentation des essais

• Test de la batterie: ache SOH (état de santé), SOC (état de charge), tension, valeur de test, résistance

interne et résultats d’analyse lisibles sur l’application ;

• Test de démarrage: analyse la tension de démarrage réelle et l’heure de démarrage, pour déterminer

rapidement l’état global du système de démarrage ;

• Test de charge: teste diérentes parties du système de charge, y compris le générateur, le redresseur, la

diode de redressement, etc., an d’obtenir une valeur de tension de charge able.

FR

33 34

1. Essai de Batterie (12V seulement)

1) Ouvrez l’application sur votre appareil mobile ou votre tablette et connectez-vous.

2) Cliquez sur « Se connecter au BTMobile Pro » pour rechercher le nom d’appareil correspondant.

3) Cliquez sur le nom de l’appareil correspondant pour vous connecter.

Dans l’interface

principale, cliquez sur «

Essai de Batterie ».

4) 5) Sélectionnez le type de batterie et cliquez

sur le type correspondant.

FR

35 36

6) 7)

Sélectionnez la norme

de batterie indiquée

sur l’étiquette

de la batterie et

cliquez sur le type

correspondant.

Sélectionnez la norme de batterie indiquée sur l’étiquette de la batterie et cliquez sur «Conrmer»

pour la conrmation.

Remarque: si la batterie est soumise à la norme JIS, veuillez consulter les valeurs gurant dans le

tableau et choisir CCA (SAE) comme norme de test (veuillez rechercher sur google JIS to CCA).

FR

La page charge ...

Topdon BTMOBILE PRO Manuel utilisateur

Topdon BTMOBILE PRO Manuel utilisateur

dans d''autres langues

Documents connexes