Mellanox Technologies InfiniScale III M2401G 20Gb/s InfiniBand Manuel utilisateur

Marque: Mellanox Technologies

Modèle: InfiniScale III M2401G 20Gb/s InfiniBand

Taper: Manuel utilisateur

Ce manuel convient également à

InfiniScale III

Mellanox Technologies

Third party information brought

to you courtesy of Dell.

InfiniScale® III M2401G 20Gb/s InfiniBand

Blade Switch I/O Module for PowerEdge

M-Series User Manual

PN: M2401G

Rev 1.8

Rev 1.8 Mellanox Technologies

Mellanox Technologies ConnectX, InfiniBlast, InfiniBridge, InfiniHost, InfiniRISC, InfiniScale,

and InfiniPCI are registered trademarks of Mellanox Technologies, Ltd. Virtual Protocol Intercon

nect is a trademark of Mellanox Technologies, Ltd. Dell and the Dell logo are trademarks of Dell

Inc. All other marks and names mentioned herein may be trademarks of their respective companies.

Third party information brought to you courtesy of Dell.

InfiniScale® III M2401G 20Gb/s InfiniBand Blade Switch I/O Module for PowerEdge M-Series

User Manual

Document Number: 2948

Mellanox Technologies, Inc.

350 Oakmead Parkway

Sunnyvale, CA 94086

U.S.A.

www.Mellanox.com

Tel: (408) 970-3400

Fax: (408) 970-3403

Mellanox Technologies Ltd

PO Box 586 Hermon Building

Yokneam 20692

Israel

Tel: +972-4-909-7200

Fax: +972-4-959-3245

NOTE:

THIS INFORMATION IS PROVIDED BY MELLANOX FOR INFORMATIONAL PURPOSES ONLY AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL

MELLANOX BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSE

QUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLI

GENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS HARDWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

M2401G 20Gb/s InfiniBand Blade Switch I/O Module User Manual

Mellanox Technologies Rev 1.8

Contents

Contents 3

About this Manual 4

Revision History 5

Chapter 1 Overview 6

1.1 InfiniBand Connectors 7

1.2 Switch Status Lights 7

Chapter 2 Installation and Basic Operation 9

2.1 Installation Safety Warnings 10

2.2 Mechanical Installation 11

2.2.1 Removing an Old Switch From the Chassis 11

2.2.2 Removing a Blank Cover Plate From the Chassis 12

2.2.3 Installing the Mellanox M2401G Switch Into the Dell Chassis 12

2.3 Power Connections and Initial Power On 12

2.4 InfiniBand Cable Installation 13

Chapter 3 Cluster Management and Firmware 14

3.1 Network Management and Clustering Software 14

3.2 Updating Firmware 14

3.2.1 Instructions for Reprogramming Over the InfiniBand Network 14

Chapter 4 Troubleshooting 17

Appendix A Specifications 18

Appendix B Mechanical Drawing 19

Appendix C EMC Certification Statements 20

Appendix D InfiniBand Connector Pinout 22

Appendix E Avertissements de sécurité d’installation 24

Appendix F Installation - Sicherheitshinweise 26

Rev 1.8 Mellanox Technologies

About this Manual

This manual describes the installation and basic use of the InfiniScale® III M2401G 20Gb/s Infini-

Band blade switch I/O module for PowerEdge M-Series.

Intended Audience

This manual is intended for users and system administrators responsible for installing and setting

up the switch platforms listed above.

The manual assumes familiarity with the InfiniBand® Architecture Specification.

Related Documentation

The documentation set accompanying the Mellanox M2401G includes the following:

Online Resources

• Mellanox Technologies Web pages: http://www.mellanox.com

• Dell Support Web pages: http://support.dell.com

Conventions

Throughout this manual, the name M2401G and the term switch are used to describe the M2401G

20Gb/s InfiniBand blade switch I/O module, unless explicitly indicated otherwise.

Table 1 - Reference Documents

InfiniBand Architecture Specification Vol-

ume 1 Release 1.2.1 and Volume 2 release

1.2.1

InfiniBand architecture specification descriptions

Mellanox OFED Stack The Mellanox OFED stack provides a tool set to manage InfiniBand fabric clusters. The

stack with user’s manual can be downloaded at:

http://www.mellanox.com > Downloads > InfiniBand SW/Drivers,

Be sure to download the stack that matches your OS.

Mellanox Firmware Tools (MFT)

User’s Manual

Document # 2329

The MFT (Mellanox Firmware Tools) package is a set of firmware tools. The manual

supplied with this package provides an overview of the firmware its installation and

replacement. The MFT can be downloaded with its documentation at:

http://www.mellanox.com > Downloads > Firmware Tools

M2401G 20Gb/s InfiniBand Blade Switch I/O Module User Manual

Mellanox Technologies Rev 1.8

Revision History

Table 2 - Revision History Table

Date Revision Description

Mar. 2009 Rev 1.8 Modified product description and document title

Mar. 2009 Rev 1.7 Added Dell flat black Logo

Dec. 2008 Rev 1.6 Minor fixes to Rev 1.5

Dec. 2008 Rev 1.5 Minor fixes to Rev 1.4

Added Instructions for Reprogramming Over the InfiniBand Network

Nov. 2008 Rev 1.4 Added Dell logo and Dell 3rd party info statement

Replaced Mellanox address

Fixed Links to new web site

Aug. 2008 Rev 1.3 Added Certs and Link to FW

Aug. 2008 Rev 1.2 Added appendix with safety warnings in French for Canada Certification

July 2008 Rev 1.1 Fixed Max Ambient Temperature

June 2008 Rev 1.0 First Draft

Rev 1.8 Mellanox Technologies

1 Overview

The InfiniScale® III M2401G 20Gb/s InfiniBand blade switch I/O module for PowerEdge M-

Series provides a high bandwidth, low latency, low power fabric for Enterprise Data Center and

High-Performance Computing environments. Based on the third generation InfiniScale® III Infini

Band switch device, the platform delivers an ideal balance between cost and performance. When

used in conjunction with ConnectX® InfiniBand dual port I/O cards clustered data bases, parallel

ized applications and transactional services applications will achieve significant performance

improvements resulting in reduced completion time and lower cost per operation.

The switch platform comes pre-installed with all necessary firmware, and configured for standard

operation within an InfiniBand fabric, and requires an InfiniBand compliant Subnet Manager run

ning from one of the hosts. All that is required for normal operation is to follow the usual precau-

tions for installation and connection from the switch to the HCAs or other switches. Once

connected, the Subnet Management software automatically configures and begins utilizing the

switch.

It is recommended that Mellanox OpenFabrics software package be installed on all nodes con-

nected to the M2401G. The software package provides a subnet manager and network management

tools as well as connectivity software for servers and storage, and is available on the Mellanox web

site. See

“Cluster Management and Firmware” on page 14. for more information.

Basic installation, hot-swapping components and hardware maintenance is covered in “Installa-

tion and Basic Operation” on page 9.

The M2401G switch has a Hot Swap controller and a PSOC Management IC.

Figure 1: Switch Front Panel and Locking Mechanism

Locking Mechanism

Switch Status Lights

M2401G 20Gb/s InfiniBand Blade Switch I/O Module User Manual

Mellanox Technologies Rev 1.8

1.1 InfiniBand Connectors

InfiniBand connectivity has 8 microGiGa connectors through the front panel. The remaining 16

interfaces are through the AirMax Midplane Connector out the back of the switch.

Figure 1 shows

the front 8 ports.

Each of the InfiniBand ports has two LEDs located next to the connector. The green LED, when lit,

indicates that a valid physical connection to the other system (switch or HCA port) exists. The yel

low LED when lit, indicates that the Subnet Manager is running and a valid data link exists. The

yellow LED illuminates when the InfiniBand network is discovered over the physical link. A valid

data activity link without data transfer is designated by a constant yellow LED indication. A valid

data activity link with data transfer is designated by a blinking yellow LED indication. If the LEDs

are not active, either the physical link or the logical link (or both) connections have not been estab

lished.

Figure 2: Physical and Logical Link Indication LEDs

1.2 Switch Status Lights

The switch Status lights indicate whether the switch is receiving power from the chassis, and the

state of the switch.

Figure 3: Indicator LEDs

LED Name Connection Status

Physical Link - Green Off – No Physical Link

ON – Physical Link

Data Activity - Yellow Blinking – indicates Data Transfer

Constant on – indicates Link exists

with no Data Transfer taking place

Off with green LED lit – indicates that

the Subnet Manager may not be

running

The I/O Module is on and

ready when both the blue and

green LEDs are lit.

This LED can be blue or

amber. A fault is indicated

when the amber LED is blink-

ing. See Table 3.

Rev 1.8 Mellanox Technologies

Table 3 - IOM states and LED configurations:

LED

Switch Status

Indication Green Status

OFF OFF OFF

ON OFF Boot in Progress

Switch not ready

Blinking Blue

ON BLINKING BLUE The CMC is identifying

the newly installed switch

ON ON BLUE Switch is on and operating Normally

ON ON or BLINKING

AMBER

Fault in System

Self-diagnosed

OFF ON or BLINKING

AMBER

Fault in System

CMC-detected

M2401G 20Gb/s InfiniBand Blade Switch I/O Module User Manual

Mellanox Technologies Rev 1.8

2 Installation and Basic Operation

Installation and initialization of the switch platform are straightforward processes, requiring atten-

tion to the normal mechanical, power, and thermal precautions for rack-mounted equipment. The

switch platform does not require any programming or configuration to operate as a basic Infini

Band switch and includes all of the necessary functionality to operate with external standard Infini-

Band Subnet Management software.

This section describes the installation process and basic operation of the switch platform. Please

first read the warnings sub-section carefully before carrying on with installation procedures.

Suitable electrical, mechanical and fire enclosure shall be provided by the end user.

Rev 1.8 Mellanox Technologies

2.1 Installation Safety Warnings

1. Installation Instructions

2. Over-temperature

3. Stacking the Chassis

4. During Lightning - Electrical Hazard

5. Copper InfiniBand Cable Connecting/Disconnecting

6. Rack Mounting and Servicing

7. Equipment Installation

Read all installation instructions before connecting the equipment to the power source.

This equipment should not be operated in an area with an ambient temperature exceed-

ing the maximum recommended: °C (°F). Moreover, to guarantee proper air flow, allow

at least 8cm (3 inches) of clearance around the ventilation openings.

The chassis should not be stacked on any other equipment. If the chassis falls, it can

cause bodily injury and equipment damage.

During periods of lightning activity, do not work on the equipment or connect or discon-

nect cables.

Copper InfiniBand cables are heavy and not flexible, as such they should be carefully

attached to or detached from the connectors. Refer to the cable manufacturer for special

warnings and instructions.

When this product is mounted or serviced in a rack, special precautions must be taken to

ensure that the system remains stable. In general you should fill the rack with equipment

starting from the bottom to the top.

This equipment should be installed, replaced, or serviced only by trained and qualified

personnel.

M2401G 20Gb/s InfiniBand Blade Switch I/O Module User Manual

Mellanox Technologies Rev 1.8

8. Equipment Disposal

9. Local and National Electrical Codes

2.2 Mechanical Installation

These switches are hot pluggable. It is not necessary to power down the Dell Chassis to install a

new switch or to replace an old switch with a new one.

Figure 4: Rear View of the Dell PowerEdge M1000e Chassis

Note: M2401G blades are not allowed in the Fabric A slots.

2.2.1 Removing an Old Switch From the Chassis

1. Remove any locking cables or screws that secure the old switch into the chassis.

2. Disconnect all of the InfiniBand cables from the front of the switch to be removed.

Disposal of this equipment should be in accordance to all national laws and regulations.

This equipment should be installed in compliance with local and national electrical

codes.

Latch Release Buttons

Locking Arms

Channel 2 slots

C2 B2 A2

Channel 1 slots

A1 B1 C1

Rev 1.8 Mellanox Technologies

3. Unlock the switch from the chassis by pushing the red latch release button.

4. Pull the locking arm down to a position perpendicular to the front of the chassis.

5. Pull the switch out of the chassis using the locking arm.

6. Install either a new switch or a blank IOM within one minute.

2.2.2 Removing a Blank Cover Plate From the Chassis

1. Remove any locking cables or screws that secure the blank cover plate into the chassis.

2. Unlock the blank cover plate by pushing the red latch release button.

3. Pull the locking arm down to a position perpendicular to the front of the chassis.

4. Pull the cover plate out of the chassis using the locking arm.

5. Install either a new switch or reinstall a blank IOM within one minute.

2.2.3 Installing the Mellanox M2401G Switch Into the Dell Chassis

Note: Make sure the Chassis is stable on a solid floor and that the Chassis is filled from the bot-

tom up. This will keep the center of gravity as low as possible reducing risk of tipping.

Note: The M2401G IOMs are only to be installed in Fabric B or Fabric C slots, and at least one

blade must have a matching ConnectX I/O card installed to support data flow. Within each fabric

type, you must install a module in the fabric's channel 1 slot before installing a module in the

fabric's channel 2 slot. For example, you must install a module in slot C1 before installing a

module in slot C2. Modules may be installed in Fabric B and C independently (you do not need

to install modules in Fabric B before installing modules in Fabric C slots). Refer to the Dell

PowerEdge M1000e Hardware Owners Manual for more information.

1. Follow the instructions in Section 2.2.1 or Section 2.2.2 to remove an old switch or a Blank

cover plate.

2. On the new switch, push the red latch release button.

3. Pull the lever forward until the lever is perpendicular to the front panel.

4. Push the switch into the slot until the latching mechanism is against the bar.

5. Push the lever on the latching mechanism up, making sure that the latching mechanism catches

the locking bar. The lever should now be parallel to the front panel.

6. Check the indicator lights to make sure the switch has power.

The installer should use a rack cable to support the mechanical and environmental characteristics of

a fully populated switch platform Chassis.

The rack mounting is designed to fit the PowerEdge Chassis. Take precautions to

guarantee proper ventilation for air intake at the front of the chassis and exhaust at the

rear in order to maintain good airflow at ambient temperature. Cable routing in partic

ular should not impede the air exhaust from the chassis.

2.3 Power Connections and Initial Power On

Caution: The switch platform will automatically power up when AC power is applied. There is no

power switch. Immediately upon closing the latching mechanism check to make sure that the

green switch LED is lit.

M2401G 20Gb/s InfiniBand Blade Switch I/O Module User Manual

Mellanox Technologies Rev 1.8

2.4 InfiniBand Cable Installation

All cables can be inserted or removed with the unit power on. To insert a cable, press the connector

into the port receptacle until the connector is firmly seated. The green LED indicator below each

port will light when the physical connection is established (that is, when the unit is powered on and

a cable is plugged into the port with a functioning port plugged into the other end of the connector).

After plugging in a cable, lock the connector using the latching mechanism particular to the cable

vendor. The yellow LED will light if the subnet manager is running (non blinking indicating that no

data is being transferred yet). When a logical connection is made the yellow LED will blink signi

fying data is being transferred.

To remove, disengage the locks and slowly pull the connector away from the port receptacle. Both

LED indicators will turn off when the cable is unseated.

Care should be taken not to impede the air exhaust flow through the chassis.

Note: Cable lengths should be used which allow for routing horizontally around to the side of the

chassis before bending upward or downward in the rack.

Rev 1.8 Mellanox Technologies

3 Cluster Management and Firmware

3.1 Network Management and Clustering Software

Download and install, on all nodes, the Mellanox OpenFabric software package for Linux, Win-

dows, or other operating systems from the Mellanox software website:

http://www.mellanox.com > Downloads > InfiniBand SW/Drivers

This software package provides connectivity for server and storage systems utilizing High Perfor-

mance Computing (HPC) or enterprise data center (EDC) applications across an InfiniBand fabric.

It also provides a Subnet Manager for simple network configuration and network administration

and diagnostic tools for network management.

3.2 Updating Firmware

The switch is delivered with the latest Firmware available at the time of production. New firmware

versions will be posted on the Mellanox firmware download page. Firmware can be updated in-

band using the Mellanox Firmware Tools (MFT).

You will need the Mellanox Firmware Tools package available in MLNX_OFED to update firm-

ware for this switch. It also can be downloaded from:

http://www.mellanox.com > Downloads > Firmware Tools

The latest firmware can be found at:

http://www.mellanox.com >Support >Dell

3.2.1 Instructions for Reprogramming Over the InfiniBand Network

To update an MT47396 InfiniScale III switch devices having a specific GUID (for example,

0x00000006660abcd0) or LID, the following are the recommended steps to update the device firm

ware.

1. Make sure all subnet ports are in the active state. One way to check this is to run opensm, the

Subnet Manager.

[root@mymach]> /etc/init.d/opensmd start

opensm start [ OK ]

2. Make sure the local ports are active by running ‘ibv_devinfo’.

3. Obtain the device LID. There are two ways to do that:

I. Using the “mst ib add” command:

The “mst ib add” runs the ibdiagnet tool to discover the InfiniBand fabric and then lists the discovered IB

nodes as an mst device under /dev/mst/ directory. These devices can be used for access by other MFT

tools.

[root@mymach]> mst ib add

-I- Running ibdiagnet to discover the fabric ...

Loading IBDIAGNET from: /usr/local/lib/ibdiagnet1.2

-W- Topology file is not specified.

M2401G 20Gb/s InfiniBand Blade Switch I/O Module User Manual

Mellanox Technologies Rev 1.8

Reports regarding cluster links will use direct routes.

Loading IBDM from: /usr/local/lib/ibdm1.2

-I- Using port 1 as the local port.

-I- Discovering ... 3 nodes (2 Switches & 1 CA-s) discovered.