Yamaha NP-S2000 Le manuel du propriétaire

Marque: Yamaha

Modèle: NP-S2000

Taper: Le manuel du propriétaire

Network Player

Lecteur Réseau

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

NP-S2000_OM_UB_cv1_4.fm Page 1 Wednesday, September 22, 2010 2:16 PM

Black process 45.0° 240.0 LPI

i En

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within

an equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions

in the literature accompanying the appliance.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has

two blades and a third grounding prong. The wide blade

or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been

dropped.

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit. Retain

this manual in a safe place for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is

often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group

recommend you to avoid prolonged exposure from excessive volume levels.

ii En

English

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC,

to use the product.

2 IMPORTANT:

When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to

follow instructions could void your FCC authorization to

use this product in the USA.

3 NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15

for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will

not result in harmful interference with other electronic

devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300 ohm

ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can

not locate the appropriate retailer, please contact

Yamaha Electronics Corp., USA 6660 Orangethorpe

Ave., Buena Park, CA 90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-003.

COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation, USA

Address: 6660 Orangethorpe Avenue

Buena Park, CA 90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Network Player

Model Name: NP-S2000

• This device complies with Part 15 of the FCC Rules.

• Operation is subject to the following conditions:

– This device may not cause harmful interference.

– This device must accept any interference received including

interference that may cause undesired operation.

See the Troubleshooting section at the end of the Owner’s

Manual (online manual) if interference to radio reception is

suspected.

iii En

HiFi Began with Yamaha

Yamaha’s involvement with and passion for music goes back

more than a century, to when we built our first reed organ in

1887. Now we are the world’s leading producer of pianos and

other musical instruments, and are involved with music in many

other ways as well. We manufacture professional recording

equipment, we design concert halls and we assist artists at

concerts with set up and sound tuning.

This knowledge and experience benefits our production of

audio components in many ways. We introduced our first HiFi

(High Fidelity) turntable in 1955. Thereafter we were one of the first

to offer mass-produced, high quality audio equipment,

and introduced many legendary stereo components.

We hope you enjoy the genuine HiFi experience of

Yamaha Natural Sound.

iv En

English

CA-1000NS-20

NS-1000M

NS-10M

GT-2000

C-2

NS-690

B-1

B-6

GT-CD1AX-2000

Soavo-2Soavo-1

PX-1

Excellence in Audio Achievement

1922: We introduced a high-quality hand-

wound phonograph.

Since 1955, we have released many HiFi

components, including turntables, tuners,

integrated amplifiers, control amplifiers,

power amplifiers and speakers.

NS-20 Monitor Speaker

CA-1000 Integrated Amplifier

Featuring A-Class operation, the CA-1000 set

the standard for integrated amplifiers.

NS-690 Monitor Speaker

NS-1000M Monitor Speaker

A truly legendary speaker still revered by HiFi enthusiasts

B-1 Power Amplifier

An innovative power amp that used FETs in all stages

C-2 Control Amplifier

Received top prize at the Milan International Music

and HiFi Show.

NS-10M Studio Monitor Speaker

Became of the most popular studio monitors in the world.

A-1 Integrated Amplifier

PX-1 Turntable

Yamaha’s first linear tracking turntable

B-6 Power Amplifier

Pyramid-shaped power amplifier with X power supply and

X amplifier

GT-2000/L Turntable

Ultra-precise heavyweight player embodying GT concept

CD-1 CD Player

First CD Player introduced in 1983

B-2x Power Amplifier

MX-10000 Power Amplifier and

CX-10000 Control Amplifier

Amplifier that redefined the capabilities of separate

components

100th anniversary model

AX-2000 Integrated Amplifier

High S/N ratio (128 dB), digital direct function equipped

GT-CD1 CD Player

Top-loading type player with integrated separate structure

MX-1 Power Amplifier and CX-1 Control

Amplifier

Soavo-1 and Soavo-2 Natural Sound

Speaker Systems

A-S2000 Stereo Amplifier and

CD-S2000 Super Audio CD Player

A-S1000 Stereo Amplifier and

CD-S1000 Super Audio CD Player

v En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances

around this unit.

Top: 10 cm (4 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the wall outlet.

16 Be sure to read the “Troubleshooting” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press the power switch (on the

main unit) downward to turn off this unit and then

disconnect the AC power plug from the AC wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit

alone for cooling.

20 Install this unit near the AC outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like. When you dispose of

batteries, follow your regional regulations.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn off this

unit by the power switch (on the main unit).

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

WARNING

THE POWER SUPPLY CABLE OF THIS UNIT MUST BE

CONNECTED TO THE MAIN SOCKET OUTLET VIA A

PROTECTIVE EARTHING CONNECTION.

1 En

English

SUPPLIED ACCESSORIES.............................................................................................................. 2

GENERAL FLOWCHART ...............................................................................................................3

SYSTEM STRUCTURES................................................................................................................... 4

Basic system.........................................................................................................................................................4

Full system ...........................................................................................................................................................5

Roles of each component .....................................................................................................................................6

Supported audio files............................................................................................................................................6

PREPARATIONS ............................................................................................................................... 7

Connections..........................................................................................................................................................7

Downloading the dedicated applications .............................................................................................................8

Turning on this unit..............................................................................................................................................9

COMMUNICATION SETUP .......................................................................................................... 10

Media sharing setup ...........................................................................................................................................10

Media controller setup........................................................................................................................................10

CONTENT BROWSING AND PLAYBACK................................................................................. 12

Operations from PC browser..............................................................................................................................12

Operations from iPhone/iPod touch ..................................................................................................................13

Operations from main unit or remote control ....................................................................................................14

Presetting favorite contents................................................................................................................................15

SETUP MENU................................................................................................................................... 17

Setup menu operations .......................................................................................................................................17

Setup menu list...................................................................................................................................................18

Advanced setup menu ........................................................................................................................................19

CONTROLS AND FUNCTIONS .................................................................................................... 20

Front panel .........................................................................................................................................................20

Remote control...................................................................................................................................................21

ADDITIONAL INFORMATION .................................................................................................... 22

Basic information on this unit............................................................................................................................22

Troubleshooting .................................................................................................................................................24

Taking care of this unit ......................................................................................................................................26

SPECIFICATIONS........................................................................................................................... 27

CONTENTS

About this manual

• This manual is produced prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and product, the product has priority.

• Pictures and illustrations (screen display, etc.) used in this manual may be different from actual products

depending on use environments.

• Notes contain important information about safety and operating instructions. y indicates a tip for your operation.

Thank you for purchasing Yamaha Network Player NP-S2000. By connecting this unit to your home network and audio

system, you can enjoy Internet radio (vTuner) or music files stored on your music servers (PCs and NAS) in the same

network.

Also, you can select a playback source or operate this unit not only from the supplied remote control but also from an

external media controller such as PC browsers and the dedicated iPhone/iPod touch application.

If you are not familiar with “DLNA” or “Internet radio”, please read “Basic information on this unit” () P.22) at the beginning.

Introduction

2 En

Check that you have received all of the following items.

• Remote control

• Batteries (AA, R6, UM-3) x 2

• Power cable

• RCA stereo cable

• TwonkyMedia server License Key brochure

■ Note on transport tape

Upon shipment from the factory, magnet feet are fixed

with transport tape to this unit’s feet. Remove the

transport tape before placing this unit.

■ Installing the batteries

1 Press the part and slide the battery cover off.

2 Insert two supplied AA batteries according to the

polarity markings (+ and –).

3 Slide the cover back until it snaps into place.

Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or

stove

– places of extremely low temperatures

– dusty places

• Insert the battery according to the polarity markings

(+ and –).

• Change all batteries if the operation range of the remote

control narrows.

• If the batteries run out, immediately remove them from

the remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries

immediately, taking care not to touch the leaked

material. If the leaked material comes into contact with

your skin or gets into your eyes or mouth, rinse it away

immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This

may shorten the life of the new batteries or cause old

batteries to leak.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Specification of

batteries may be different even though they look the

same.

• Before inserting new batteries, wipe the compartment

clean.

• Dispose of batteries according to your regional

regulations.

SUPPLIED ACCESSORIES

RETURN

PUSH

SELECT

ENTER

SOURCE

OFF

LINK

3 En

English

The following flowchart explains general setup procedures required to enjoy streaming music or Internet radio using this

unit.

GENERAL FLOWCHART

Step 1: Deciding the system structure ) P.4

Decide the system to establish and check the requirements.

Step 2: Connections ) P.7

Connect this unit to your PC system and audio system.

Step 3: Downloading the dedicated applications ) P.8

From the website, download the dedicated applications required for your system.

Step 4: Turning on this unit ) P.9

Power on this unit and other system components.

Step 5: Media sharing setup ) P.10

Configure the media sharing settings of your digital media server.

Step 6: Media controller setup ) P.10

Search the network players in your home network and establish a connection between an external media

controller (PC) and this unit.

Step 7: Playback ) P.12

Select music or Internet radio station to listen to.

4 En

This section describes two major system structure examples and what you can do with each system.

The following figure shows a minimum configuration to utilize the basic functions of this unit.

With this system structure, you can do...

• Easily establishing a communication between your PC and this unit using the dedicated PC setup application.

• Selecting playback source from a browser on any PC in the same network or remote control

– Browsing music stored on your PC

– Selecting Internet radio stations

■ Requirements

To establish the “basic system”, all of the following requirements should be met.

Audio system

Your amplifier has an audio input jack.

A speaker set is connected to your amplifier.

For details on a connection between your audio system and this unit, see “Connections” () P.7). Please also refer to the manual of your

audio devices.

PC network system

Your PC is connected to the Internet via the broadband router.

Your PC has a disc drive capable of ripping CDs and enough hard drive space to store audio files.

• For details on Internet connection, please refer to the manual of your network devices.

• For details on a connection and communication setup between your PC and this unit, see “Connections” () P.7) and

“COMMUNICATION SETUP” () P.10).

SYSTEM STRUCTURES

Basic system

RETURN

PUSH

SELECT

ENTER

SOURCE

OFF

LINK

Your audio system Your PC network system

Speakers

Amplifier

Balanced, digital audio

(optical or coaxial), or

analog stereo cable

To AC outlet

This unit (NP-S2000)

Broadband

router

Modem

Internet

Remote control

Network cable

SYSTEM STRUCTURES

5 En

English

The following figure shows a recommended configuration to take full advantage of the functions of this unit.

With this system structure, you can do...

• All features listed in “Basic system” () P.4)

• Delivering music stored on your NAS (without starting your PC)

• Selecting playback source from your iPhone/iPod touch

– Browsing music stored on your PC and NAS

– Selecting Internet radio stations

■ Requirements

To establish the “full system”, all of the following requirements should be met.

Audio system

Your amplifier has an audio input jack.

A speaker set is connected to your amplifier.

For details on a connection between your audio system and this unit, see “Connections” () P.7). Please also refer to the manual of your

audio devices.

PC network system

Your PC is connected to the Internet via the WiFi broadband router.

Your PC has a disc drive capable of ripping CDs and enough hard drive space to store audio files.

Your NAS is compatible with DLNA and works with your PC and WiFi broadband router properly.

• For details on Internet connection, please refer to the manual of your network devices.

• For details on a connection and communication setup between your PC and this unit, see “Connections” () P.7) and

“COMMUNICATION SETUP” () P.10).

iPhone/iPod touch

Your iPhone/iPod touch is wirelessly connected to the WiFi broadband router.

Full system

RETURN

PUSH

SELECT

ENTER

SOURCE

OFF

LINK

Your audio system

Your PC network system

Speakers Amplifier

Balanced, digital audio

(optical or coaxial), or

analog stereo cable

This unit (NP-S2000)

Modem

Internet

iPhone/

iPod touch

NAS

WiFi

broadband

router

Network cable

To AC outlet

Remote control

SYSTEM STRUCTURES

6 En

This section describes rolls of each component in the

system.

This unit (NP-S2000)

Decodes digital audio signals received from your PC

network system and sends the signals to your audio

system so that you can enjoy digital music stored on a PC

or NAS, or Internet radio in high-quality sounds.

Remote control

With the remote control, you can select a playback source

or operate this unit while viewing information on the front

panel display of this unit.

Amplifier and speakers

Receive audio signals from this unit and produce sounds.

• Stores music files ripped from CDs or downloaded and

works as a DLNA digital media server.

• By installing the dedicated PC setup application on your

PC, you can configure the communication setup

between your PC and this unit.

• With a browser (Internet Explore 6.0 or later), you can

select a playback source or operate this unit.

Broadband router (WiFi broadband router)

Connects your PC and this unit to the Internet. A WiFi

broadband router also works as a bridge between your

iPhone/iPod touch and this unit in the network.

NAS (Network attached storage)

Stores music files ripped from CDs or downloaded and

works as a DLNA digital media server, enabling you to

enjoy music without starting your PC.

iPhone/iPod touch

By installing the dedicated application on your iPhone/

iPod touch, you can use it as an external controller. You

can select playback source or operate this unit while

viewing the iPhone/iPod touch screen.

This unit supports the following audio files stored on a PC

or a NAS.

Audio format:

WAV, FLAC, MP3, AAC, WMA

• Playable audio formats vary depending on the media server.

For example:

– Windows Media Player 12 supports WAV, MP3, AAC and

WMA.

– Windows Media Player 11 supports WAV, MP3 and WMA.

– TwonkyMedia server (supplied) supports all audio formats

listed above.

For details, visit “http://download.yamaha.com/file/45350”.

• We recommend WAV and FLAC as audio formats producing

high-quality sounds.

Sample rate:

96, 88.2, 64, 48, 44.1, 32, 24, 22.05, 16, 12, 11.025, 8

(kHz)

Bit depth:

16, 24 (bit)

Roles of each component Supported audio files

7 En

English

This section describes preparations required before operating this unit.

Depending on the system structure you want to establish, make cable connections of the system components.

1 Connect this unit to your amplifier with an XLR

balanced cable, RCA stereo cable, coaxial digital

audio cable or optical cable.

Select one of the audio connections shown above. If your

amplifier is equipped with XLR balanced input jacks, we

recommend a balanced connection for optimum audio

performance.

2 Connect this unit to your broadband router with an

STP (shielded twisted pair) network cable (CAT-5 or

higher straight cable).

3 Connect the power cable to AC IN and then plug

into an AC outlet.

■ About the spike feet

The feet of this unit include built-in spikes that can reduce

the effect of vibrations on the set. To use the spikes,

remove the magnet foot by pulling it. Also, you can adjust

the height of each foot by rotating it if this unit is unstable.

PREPARATIONS

Connections

BALANCED OUT BALANCED OUT

NETWORK

SYSTEM CONNECTOR

DIGITAL OUT

OPTICAL COAXIAL AC INR ANALOG OUT

OUTPUT

RL L

LAN

WAN

Speakers Amplifier

XLR balanced

cable

RCA

stereo cable

(supplied)

Optical cable

Coaxial digital

audio cable

Internet

Modem

Broadband

router

This unit (NP-S2000) *U.S.A model

Power cable (supplied)

To AC outlet

NAS

(for full system only)

* Used for product inspection service

Caution

The spikes may scratch the shelf or floor. We recommend you use

a support when placing this unit on expensive furniture, etc.

Spike

Magnet foot

PREPARATIONS

8 En

■ About the BALANCED OUT jacks

The pin assignments for the BALANCED OUT jacks of

this unit are shown below. Before connecting an XLR

balanced cable, refer to the manual of your amplifier and

verify that its XLR balanced input jacks are compatible

with the pin assignments.

When connecting to this unit, be sure to match the pins

and insert the connector of the “female” XLR balanced

cable until you hear a click. When disconnecting, hold

down the lever of the connector and then pull it out.

Visit the following website for information about

downloading the dedicated applications.

http://download.yamaha.com/file/45350

The latest information on this unit (owner’s manual, FAQ, etc.) is

also available in the download file.

■ Network Player Search

This application enables you to easily search the network

players in your home network from your PC and start the

browser to select playback source or operate this unit.

Please read “License agreement” () P.28) before using this

application.

■ Network Player Controller

This application (for iPhone/iPod touch) enables you to

select playback source or operate this unit from your

iPhone/iPod touch.

■ TwonkyMedia server

For details, refer to “TwonkyMedia server License Key

brochure” supplied with this unit.

2: hot1: ground

3: cold

“Female” XLR connector

“Male” XLR connector

Downloading the dedicated

applications

Note

Full System

PREPARATIONS

9 En

English

If you have established all cable connections, turn on this unit and other system components.

When the power switch on main unit is set to STANDBY/ON, you can switch this unit between on and standby by pressing the power

button on the remote control () P.21).

Turning on this unit

RETURN

PUSH

SELECT

ENTER

SOURCE

OFF

LINK

Set the power switch to STANDBY/ON

10 En

This section describes the setup required on digital media

servers (PC or NAS) and controllers (PC).

To enable a sharing of PC/NAS music contents over the

network, configure the sharing setting of the media server.

■ Sharing setup on PC

When using Windows Media Player 12

(on Windows 7)

1 In “Control Panel”, select “Choose

homegroup and sharing options”

under “Network and Internet”.

2 Check the “Stream my pictures,

music, and videos to all devices on

my home network” box and then

select “Choose media streaming

options”.

3 Select “Allowed” from the drop-

down menu next to “NP-S2000”.

4 In the same way, select “Allowed”

from the drop-down menu next to

“Media programs on this PC and

remote connections”.

5 Click “OK” to exit.

Since this unit supports Windows 7, you can directly control

playback of this unit from Windows Media Player 12.

When using Windows Media Player 11

1 Start Windows Media Player 11 on

your PC.

2 Select “Library” and then “Media

Sharing”.

3 Check the “Share my media to” box,

select the “NP-S2000” icon and then

click “Allow”.

4 In the same way, select the icons for

devices to be used as external media

controllers (other PCs and iPhone/

iPod touch) and then click “Allow”.

5 Click “OK” to exit.

When using TwonkyMedia server

If you have saved music files on your PC with iTunes

(Non-DRM AAC/MP3 files), you can enable music

streaming by using TwonkyMedia server. For details,

refer to “TwonkyMedia server License Key brochure”

supplied with this unit.

Change the media receiver setting on TwonkyMedia

server to allow this unit and devices to be used as external

media controllers (other PCs and iPhone/iPod touch) to

access TwonkyMedia server.

■ Sharing setup on NAS

Refer to the manual of your NAS and change the media

sharing setting on the NAS to allow this unit and devices

to be used as external media controllers (other PCs and

iPhone/iPod touch) to access the NAS.

To select a playback source or operate this unit from

external media controllers, first you need specify the IP

address of this unit on a browser (Internet Explore 6.0 or

later). By using the dedicated application “Network Player

Search”, you can easily search the network players in your

home network from your PC and establish a connection.

• For details on the download of the dedicated applications, see

“Downloading the dedicated applications” () P.8).

• To use your iPhone/iPod touch as an external media controller,

see “Operations from iPhone/iPod touch” () P.13).

COMMUNICATION SETUP

Media sharing setup

Media controller setup

Full System

COMMUNICATION SETUP

11 En

English

■ Controller setup on PC

In this section, Windows 7 is used as an example.

1 Click the “NP Search.exe” in the

download folder to start “Network

Player Search”.

The “NETWORK PLAYER SEARCH” screen

appears.

The menu language is automatically selected according to the

language setting on the operating system. When using Windows,

you can also select a language from “Language” under the “Tool”

menu.

2 From the “Network Adapter” drop-

down menu, select the network

adapter connected to the network

which this unit is being connected.

3 Click “Search” to search the network

players in the network.

4 Select the model from the list and

then click “Connect”.

The network player control screen appears in the

browser.

Now you are ready to select a playback source or

operate this unit. For details, see “CONTENT

BROWSING AND PLAYBACK” () P.12).

By adding the URL of the network player control screen (IP

address of this unit) to the bookmark of the browser, you will be

able to open it without using “Network Player Search” from the

next time. However, the IP address of this unit may change if you

are using a DHCP server.

Select

Click

Select

Click

12 En

This section describes how to browse contents and start

playback from the PC browser (Internet Explore 6.0 or

later), iPhone/iPod touch or front panel/remote control of

this unit.

1 In the “Source” screen, select a

source type.

• The “Source” screen is displayed after following the procedure

in “Controller setup on PC” () P.11).

• Select “Setup” to configure the settings of this unit () P.17).

2 Select a menu item until you find a

desired content and then start

playback.

Menu screen

1 Return

Move to the previous menu screen.

2 Now Playing

Move to the playback information screen.

3 Menu items

4 Source

Move to the “Source” screen.

5 Home

Move to the top menu screen.

6 Page Up/Page Down

Switch the pages of the menu list.

CONTENT BROWSING AND PLAYBACK

Operations from PC browser

45 6

CONTENT BROWSING AND PLAYBACK

13 En

English

Playback information screen

1 Return

Move to the previous screen.

2 Album art or station icon (if available)

3 Playback information

Shows the information on the playback content.

4 Playback functions

DLNA:

Z (play), (pause), (skip backward),

(skip forward)

Internet Radio:

Z (play), (stop)

5 Source

Move to the “Source” screen.

6 Home

Move to the top menu screen.

7 Shuffle (for “DLNA” only)

Switch the shuffle mode (on, off).

8 Repeat (for “DLNA” only)

Switch the repeat mode (repeat all, repeat single, off).

You can register your favorite Internet Radio stations by

accessing the “vTuner Radio Guide” website with a PC browser.

To use this feature, you need the MAC address of this unit

() P.18) and your e-mail address to create your personal

account. For details, visit “http://yradio.vtuner.com/”.

By using the dedicated application “Network Player

Controller” () P.8), you can browse contents and start

playback from your iPhone/iPod touch.

1 Tap the “NP Controller” icon on your

iPhone/iPod touch to start “Network

Player Controller”.

2 In the “Player Select” screen, select

a network player to connect to.

• This screen is skipped when only one network player has been

detected.

• To search the network players again, tap “Search”.

3 Follow the procedure in “Operations

from PC browser” () P.12).

• To update the media server list, tap “Search”.

• To reload the content list of the selected media server, tap

“Load”. Reload the content list when you have added or deleted

any content on the media server.

5678

Operations from iPhone/iPod touch

Full System

CONTENT BROWSING AND PLAYBACK

14 En

For details on the controls on the front panel/remote control, see

“CONTROLS AND FUNCTIONS” () P.20).

1 Press SOURCE repeatedly to select

a source type.

2 Use the following controls to select a

menu item until you find a desired

content.

Main unit

Jog dial

Rotate to select a menu item and press to confirm the

selection.

RETURN

Show the upper-level menu in the front panel display.

Remote control

Cursor buttons/ ENTER

Press S/T to select a menu item (or press W/X

repeatedly to select from the gauge) and press

ENTER to confirm the selection.

RETURN

Show the upper-level menu in the front panel display.

HOME

Show the top-level menu in the front panel display.

NOW PLAYING

Show the playback information in the front panel

display.

3 If playback starts, use the following

controls to operate desired

functions.

Main unit

Jog dial

Rotate left to skip backward and right to skip

forward. Press to start or pause playback.

RETURN

Show the previous menu in the front panel display.

Operations from main unit or

remote control

RETURN

PUSH

SELECT

ENTER

SOURCE

DIMMER

REPEAT

MEMORY

DISPLAY

SHUFFLE

SOURCE

D L N A

Internet Radio

Symphony #9-4

RETURN

PUSH

SELECT

ENTER

SOURCE

RETURN

Jog dial

RETURN

NOW PLAYING HOME

ENTER

RETURN

Cursor buttons/

ENTER

HOME

NOW PLAYING

Symphony #9-4

RETURN

PUSH

SELECT

ENTER

SOURCE

RETURN

Jog dial

La page charge ...

Yamaha NP-S2000 Le manuel du propriétaire

Marque: Yamaha

Modèle: NP-S2000

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Yamaha NP-S2000 Owner's manual

Yamaha NP-S2000 Le manuel du propriétaire

Yamaha NP-S2000 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents