Campbell Hausfeld DC200000 Manuel utilisateur

Oilless Compressors

Operating Instructions and Parts Manual

Models: DC130010 and DC200000

IN641900AV 8/16

A Marmon/Berkshire Hathaway Company

EN

REGISTER YOUR PRODUCT ONLINE NOW! www.campbellhausfeld.com

READ AND FOLLOW ALL INSTRUCTIONS • SAVE THESE INSTRUCTIONS • DO NOT DISCARD

Please read and save these instructions. Read carefully before attempting to

assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply

with instructions could result in personal injury and/or property damage! Retain

instructions for future reference.

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to

this manual or file it for safekeeping.

Model #: __________________________

Serial #: ___________________________

Purchase Date: _____________________

For parts, product & service information

visit www.campbellhausfeld.com

Campbell Hausfeld

100 Production Drive

Harrison, Ohio 45030

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

1

BEFORE YOU BEGIN

Description

This residential oilless compressor is designed for do-it-yourselfers with a variety of home and automotive

jobs. These compressors power spray guns, impact wrenches and other tools. Compressed air from this unit

will contain moisture. Install a water filter or air dryer if application requires dry air.

UNPACKING

Do not lift or move unit without appropriately rated equipment. Be sure the unit is securely

attached to lifting device used. Do not lift unit by holding onto tubes or coolers. Do not use unit

to lift other attached equipment.

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for

loose, missing or damaged parts. Check to be sure all supplied accessories are enclosed with the unit. In case

of questions, damaged or missing parts, please visit www.campbellhausfeld.com for customer assistance.

Do not operate unit if damaged during shipping, handling or use. Damage may result in

bursting and cause injury or property damage.

GENERAL SAFETY INSTRUCTIONS

Safety Guidelines

This manual contains information that is very important to know and understand. This information is

provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe

the following symbols.

Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death

or serious injury.

Warning indicates a potentially hazardous situation which, if not avoided, COULD result in

death or serious injury.

Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or

moderate injury.

Notice indicates important information, that if not followed, may cause damage to equipment.

IMPORTANT or NOTE: Information that requires special attention.

Safety Symbols

The following Safety Symbols appear throughout this manual to alert you to important safety hazards and

precautions.

Risk of

Hot Parts

Risk of

Explosion

Risk of

Pressure

Risk of Shock

MANUAL

Read

Manual

First

Risk of

Fire

Wear eye

and hearing

protection

Wear Eye

and Mask

Protection

MAINTENANCE /

REPAIR

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

2

GENERAL SAFETY INSTRUCTIONS (CONTINUED)

California Proposition 65

This product or its power cord may contain chemicals known to the State of California to cause

cancer and birth defects or other reproductive harm. Wash hands after handling.

You can create dust when you cut, sand, drill or grind materials such as wood, paint,

metal, concrete, cement, or other masonry. This dust often contains chemicals known

to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

Important Safety Information

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the

product described. Protect yourself and others by observing all safety information. Failure to comply with instructions

could result in personal injury and/or property damage! Retain instructions for future reference.

This manual contains important safety, operational and maintenance information. If you have any

questions, lease visit www.campbellhausfeld.com for customer assistance.

BREATHABLE AIR WARNING

This compressor/pump is not equipped and should not be used “as is” to supply breathing quality

air. For any application of air for human consumption, the air compressor/pump will need to be

fitted with suitable in-line safety and alarm equipment. This additional equipment is necessary to

properly filter and purify the air to meet minimal specifications for Grade D breathing as described in

Compressed Gas Association Commodity Specification G 7.1, OSHA 29 CFR 1910. 134, and/or Canadian

Standards Associations (CSA).

DISCLAIMER OF WARRANTIES

In the event the compressor is used for the purpose of breathing air application and proper in-line

safety and alarm equipment is not simultaneously used, existing warranties shall be voided, and

Campbell Hausfeld disclaims any liability whatsoever for any loss, personal injury or damage.

General Safety

Since the air compressor and other components (material pump, spray guns, filters, lubricators, hoses, etc.)

used make up a high pressure pumping system, the following safety precautions must be observed at all

times:

Do not run unattended. Leaving compressor in AUTO position may allow it to turn on

inadvertently. To prevent this and possible damage from power surge, turn to OFF position after

each use.

1. Read all manuals included with this product carefully. Be thoroughly familiar with the

controls and the proper use of the equipment.

2. Follow all local electrical and safety codes as well as in the United States, the National

Electrical Codes (NEC) and Occupational Safety and Health Act (OSHA).

3. Only persons well acquainted with these rules of safe operation should be allowed to use the

compressor.

4. Keep visitors away and NEVER allow children in the work area.

5. Wear safety glasses and use hearing protection when operating the unit.

6. Do not stand on or use the unit as a handhold.

7. Before each use, inspect compressed air system and electrical components for signs of

damage, deterioration, weakness or leakage. Repair or replace defective items before using.

8. Check all fasteners at frequent intervals for proper tightness.

Motors, electrical equipment and controls can cause electrical arcs that will ignite a

flammable gas or vapor. Never operate or repair in or near a flammable gas or vapor.

Never store flammable liquids or gases in the vicinity of the compressor.

Compressor parts may be hot even if the unit is stopped.

9. Keep fingers away from a running compressor; fast moving and hot parts will cause injury

and/or burns.

MANUAL

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

3

GENERAL SAFETY INFORMATION (CONTINUED)

10. If the equipment should start to vibrate abnormally, STOP the engine/motor and check immediately for

the cause. Vibration is generally a warning of trouble.

11. To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or excessive grease.

Never remove or attempt to adjust safety valve. Keep safety valve free from paint

and other accumulations.

Never use plastic (PVC) pipe for compressed air. Serious injury or death could result.

Never attempt to repair or modify a tank! Welding, drilling or any other

modification will weaken the tank resulting in damage from rupture or explosion.

Always replace worn, cracked or damaged tanks.

Drain liquid from tank daily.

12. Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank regularly and

inspect periodically for unsafe conditions such as rust formation and corrosion.

13. Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining

moisture or depressurizing the compressor system.

Spraying Precautions

Do not spray flammable materials in vicinity of open flame or near ignition sources

including the compressor unit.

14. Do not smoke when spraying paint, insecticides, or other flammable substances.

15. Use a face mask / respirator when spraying and spray in a well ventilated area to prevent

health and fire hazards.

16. Do not direct paint or other sprayed material at the compressor. Locate compressor as

far away from the spraying area as possible to minimize overspray accumulation on the

compressor.

17. When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the

chemical manufacturer.

MAINTENANCE /

REPAIR

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

4

SPECIFICATIONS

DC130010 DC200000

Motor HP 1.3 1.3

Tank Capacity 13 gallon 20 gallon

Phase Single Single

Number of Cylinders 1 1

Air Delivery @ 90 psi 4.0 SCFM 4.0 SCFM

Voltage 110-120 110-120

Amperes 14A 14A

Hertz (Cycle) 60 60

Maximum Pressure 150 150

Tank Outlet 1/4 in. IM 1/4 in. IM

Unit Weight 78.28 pounds 97.02 pounds

DIMENSIONS

DC130010 DC200000

Length 27.56 in. 31.5 in.

Width 12.6 in. 14.96 in.

Height 27.95 in. 30.315 in.

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

5

ASSEMBLY INSTRUCTIONS

Handle Assembly (Figure 1)

1. Place ends of handle around tank and into the

mounting pipe. Align holes in handle to holes in

mounting pipe.

2. Assemble two (2) screws (from parts package)

through holes in mounting pipe and handle.

Tighten screws.

Never use the handle to lift the unit

completely off the ground. Only

use the handle to lift one end so the wheels may be used to

move the unit.

Wheel Assembly (Figure 2)

Wheel assembly kit includes:

- 2 wheels *

- 2 axle bolts *

- 2 washers *

- 2 nuts *

The items marked with an asterisk (*) were shipped

loose with the unit.

1. Wheel has an offset hub. Place wheel insert into

center of hub. With offset hub facing axle iron,

assemble axle bolt through washer and then holes

in wheel and axle iron.

2. Place lock washer on axle bolt. Then tighten nut

securely to threaded part of axle bolt.

3. Repeat procedure with other side.

Handle

Bolt

Figure 1 - Handle Assembly

Figure 2 - Wheel Assembly

Nut

Wheel

Axle

Spring Washer

MAINTENANCE /

REPAIR

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

6

GETTING TO KNOW YOUR UNIT

Pressure Switch - Auto/Off Switch - In the “AUTO” position, the compressor shuts off automatically when

tank pressure reaches the maximum preset pressure. In the “OFF” position, the compressor will not operate.

This switch should be in the “OFF” position when connecting or disconnecting the power cord from the

electrical outlet.

Regulator - The regulator controls the amount of air pressure at the hose outlet.

ASME Safety Valve - This valve automatically releases air if the tank pressure exceeds the preset

maximum.

Exhaust Tube - This tube carries compressed air from the pump to the check valve. This tube becomes very

hot during use. To avoid the risk of severe burns, never touch the discharge tube.

Check Valve - One-way valve that allows air to enter the tank, but prevents air in the tank from flowing

back into the compressor pump.

Handle - Designed to move the compressor.

Never use the handle on wheeled units to lift the unit completely off the ground.

Drain Valve - This valve is located on the bottom of the tank. Use this valve to drain moisture from the

tank daily to reduce the risk of corrosion.

Pressure Gauges - These gauges will show air pressure in the compressor tank and at the compressor

outlet.

Outlet Pressure Gauge - Will show air pressure at the outlet in pounds per square inch (psi). Make sure

this gauge reads ZERO (by adjusting regulator knob fully counterclockwise) before changing air tools or

disconnecting air hose from outlet.

Tank Pressure Gauge - Will show air pressure in tank while the compressor is running, indicating

compressor is building pressure properly. This gauge will show maximum pressure of compressor when it

shuts off automatically at the pressure switch.

Motor Reset - (not shown, located inside motor). Designed to keep the motor from overheating. The

motor has an auto reset protector. To reset once the motor has cooled, turn the pressure switch to the OFF

position, then to the AUTO position.

This compressor is equipped with an overload protector which will shut off motor if it becomes

overloaded.

If the overload protector is actuated, the motor must be allowed to cool down for

approximately 30 minutes before it will reset.

Drain Valve

Handle

Check Valve Pressure Switch

(Auto/Off)

Outlet Gauge

Tank Gauge

Safety Valve

Regulator

Figure 3

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

7

INSTALLATION INSTRUCTIONS

Location

It is extremely important to install the compressor in a clean, dry, and well ventilated area. The compressor

must be placed on a firm, level surface where the surrounding air temperature will not be more than 100°F.

A minimum clearance of 18 inches between the compressor and a wall is required because objects could

obstruct air flow.

Do not locate the compressor air inlet near steam, paint spray, sandblast areas or any other

source of contamination. This debris will damage the motor.

Electrical Installation

All wiring and electrical connections should be performed by a qualified electrician.

Installation must be in accordance with local codes and national electrical codes.

Wiring

1. Local electrical wiring codes differ from area to area. Source wiring, plug and protector must be rated

for at least the amperage and voltage indicated on motor nameplate, and meet all electrical codes for

this minimum.

2. Use a slow blow fuse or a circuit breaker.

3. This product is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug

illustrated in Figure 4. Make sure the product is connected to an outlet having the same configuration

as the plug. This product must be grounded. In the event of an electrical short circuit, grounding

reduces risk of electrical shock by providing an escape wire for electric current. This product is equipped

with a cord having a grounding wire with an appropriate grounding plug. Plug must be plugged into

an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Overheating, short circuiting and fire damage will result from inadequate wiring.

Minimum Gauge of Extension Cord

25 ft. 50 ft. 100 ft.

14 12 10

Use of an extension cord may cause excess heat to

motor. This could lead to tripped breaker (at electrical

panel) or tripped thermal overload (on compressor

motor). If this occurs, eliminate extension cord and plug

compressor directly into electrical outlet. Avoid using

extension cords; use longer air hose(s) instead.

Grounded Outlet

Grounding

Figure 4 - Grounding Method

MAINTENANCE /

REPAIR

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

8

OPERATING INSTRUCTIONS

Before First Start-Up Break-In Procedure

(Complete this procedure before using compressor for the first time. Once completed, it is not necessary to

repeat.)

1. Open drain valve located on bottom of tank.

2. Turn ON / OFF switch to OFF position.

3. Plug in power cord.

4. Turn ON / OFF switch to ON position and run compressor for 30 minutes.

5. Turn ON / OFF switch to OFF position.

6. Unplug power cord.

7. Close drain valve.

The compressor is now ready for use.

Operating Procedure

1. Turn switch to OFF position and plug in power cord.

2. Turn regulator knob counterclockwise to close air flow.

3. Turn switch to AUTO position.

4. Compressor will build to maximum pressure and shut off.

5. With hose attached to outlet of compressor, attach tire chuck or other tool to open end of hose.

6. Adjust regulator to proper pressure for tool or tire. Operate tool per instructions.

As air is depleted from the tank by use of a tire chuck, tool, etc., the compressor will restart automatically

at its preset “cut-in” pressure. When a tool is being used continuously, the compressor will cycle on and off

automatically.

7. Turn switch to OFF position, unplug power cord and drain tank of air when finished using compressor.

MOISTURE IN COMPRESSED AIR

Moisture in compressed air will form into droplets as it comes from an air compressor pump. When

humidity is high or when a compressor is in continuous use for an extended period of time, this

moisture will collect in the tank. When using a paint spray or sandblast gun, this water will be carried

from the tank through the hose, and out of the gun as droplets mixed with the spray material.

IMPORTANT: This condensation will cause water spots in a paint job, especially when spraying other

than water based paints. If sandblasting, it will cause the sand to cake and clog the gun, rendering it

ineffective.

A filter in the air line, located as near to the gun as possible, will help eliminate this moisture.

TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Compressor will not run 1. Switch in OFF position 1. Make sure compressor is plugged in and switch is

ON.

2. No electrical power at wall outlet 2. Check circuit breaker or fuse at electrical panel.

3. Compressor has reached automatic

shut-off pressure

3. Release air from tank until compressor restarts

automatically.

4. Motor overheated 4. Allow compressor to cool for approximately 30

minutes so thermal overload switch will reset. Make

sure compressor is run in a clean, well-ventilated

area where temperature will not exceed 100°F.

5. Loose electrical connection 5. Check all electrical connections.

6. ON / OFF switch bad 6. Replace ON / OFF switch.

7. Pressure switch bad 7. Replace pressure switch.

8. Defective motor 8. Replace pump / motor assembly.

Fuses blow / circuit breaker

trips repeatedly

1. Incorrect size fuse, circuit overloaded 1. Check for proper fuse, use time-delay fuse.

Disconnect other electrical appliances from circuit

or operate compressor on its own branch circuit.

2. Extension cord usage - wrong gauge

wire and/or too long

2. Remove extension cord or refer to Extension Cord

Chart on page 5.

3. Worn check valve 3. Replace check valve.

Do not disassemble check valve

with air pressure in tank; bleed

tank.

4. Defective unloader valve (on

pressure switch)

4. Replace unloader valve.

5. Defective motor capacitor(s) 5. Replace capacitor(s).

6. Defective motor 6. Replace motor.

Tank pressure drops when

compressor shuts off

1. Loose connections (fittings, tubing,

etc.)

1. Check all connections with soap and water solution.

Tighten; or remove and apply pipe dope or pipe

tape to the threads, then reassemble.

2. Open tank drain valve 2. Close tank drain valve.

3. Tank leaks 3. Check tank for leaks with soap and water solution.

If leak is detected, tank must be replaced with

genuine replacement part.

Compressor runs continuously

and / or air output is lower

than normal / low discharge

pressure

1. Excessive air usage 1. Decrease air usage; compressor not large enough

for air requirement.

2. Clogged intake filter 2. Clean or replace filter.

3. Open tank drain valve 3. Close tank drain valve.

4. Air leaks in piping (on machine or in

outside system)

4. Check all connections with soap and water solution.

Tighten; or remove and apply pipe dope or pipe

tape to the threads, then reassemble.

5. Piston ring worn 5. Replace piston and cylinder.

6. Broken valve (in pump) 6. Replace valve.

7. Tank leaks 7. Check tank for leaks with soap and water solution.

If leak is detected, tank must be replaced with

genuine replacement part.

8. Defective pressure switch 8. Replace switch.

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

9

TROUBLESHOOTING GUIDE (CONTINUED)

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Excessive moisture in discharge

air

1. Excessive water in tank 1. Drain tank.

2. High humidity 2. Move to area of less humidity; use air line filter.

Knocks, rattles, and/or

excessive vibration

1. Loose mounting bolts 1. Tighten bolts.

2. Tank not level 2. Use sturdy wedge / object to bring tank to level

position.

3. Cylinder or piston is worn/scored 3. Replace or repair as necessary.

Compressor runs continuously

and safety valve opens as

pressure rises

1. Defective pressure switch 1. Replace switch.

2. Defective safety valve 2. Replace safety valve with genuine replacement

part.

Air leaking from unloader

valve on pressure switch

1. Check valve stuck in an open position 1. Replace check valve.

2. Unloader valve stuck in open

position

2. Replace unloader valve.

Do not disassemble check valve

with air pressure in tank; bleed

tank.

MAINTENANCE /

REPAIR

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

10

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

11

MAINTENANCE AND INSPECTION INSTRUCTIONS

Disconnect, tag and lock out power source, then release all pressure from the system

before attempting to install, service, relocate or perform any maintenance.

Check compressor often for any visible problems and follow maintenance procedures each time

compressor is used.

ASME Safety Valve

Do not remove or attempt to adjust the safety valve!

Check the safety valve by performing the following steps:

1. Plug the compressor in and run until shut off

pressure is reached.

2. Wearing safety glasses, pull the ring on the safety

valve to release pressure from compressor tank.

Use your other hand to deflect fast-moving air

from being directed toward your face.

3. The safety valve should automatically close at

approximately 40 psi - 50 psi. If the safety valve

does not allow air to be released when you pull

on the ring, or if it does not close automatically, it

MUST be replaced.

Safety valve must be replaced if it cannot be actuated or it leaks air after ring is released.

Drain Tank

1. Turn compressor off and release pressure from system. (To release pressure from system, pull ring on

ASME safety valve. Deflect escaping air by shielding valve with one hand as you pull ring with other

hand.) Pull ring until tank is empty.

A large amount of fast moving air will be released when the safety valve is opened with

pressure in the tank. Wear ANSI approved Z87.1 safety glasses.

2. Drain moisture from tank by opening drain valve underneath tank. Tilt tank to remove all moisture.

3. Clean dust and dirt from tank, air lines and pump cover while compressor is still OFF.

Intake Air Filter Maintenance

Removal, Inspection and Replacement (Figure 6).

The intake filter element should be removed and

checked periodically. A clogged intake filter can

decrease compressor performance and cause the

compressor to overheat.

1. Remove bolt.

2. Remove the filter cover and filter element. Inspect

each piece.

3. If the filter element is dirty or clogged, replace it.

4. Reinstall filter, cover, and bolt.

IMPORTANT: Locate unit as far from spraying area as hose will allow to prevent overspray from clogging

filter.

End of operation/Storage

1. Turn AUTO/OFF switch to the OFF position.

2. Unplug power cord from wall outlet and wrap around handle to prevent damage when not in use.

3. Wearing safety glasses drain tank of air by pulling the ring on the safety valve. Use other hand to

deflect fast moving air from being directed toward your face.

4. Drain tank of condensation by opening drain valve on bottom of tank. Tank pressure should be below

10 psi when draining tank.

Figure 5

Figure 6 - Intake Filter Maintenance

MAINTENANCE /

REPAIR

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

12

MAINTENANCE AND INSPECTION INSTRUCTIONS (CONTINUED)

5. Air hose should be disconnected from compressor and hung open ends down to allow any moisture to

drain.

6. Compressor and hose should be stored in a cool, dry place.

Technical Service

For information regarding the operation or repair of this product, please visit www.campbellhausfeld.com.

MAINTENANCE SCHEDULE

OPERATION DAILY WEEKLY MONTHLY

DRAIN TANK

●

CHECK AIR FILTER

●

CHECK SAFETY VALVE

●

CLEAN UNIT

●

NOTES

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

13

For Repair Parts, visit www.campbellhausfeld.com

24 hours a day – 365 days a year

Please provide following information:

- Model number

- Serial number (if any)

- Part description and number as shown in parts list

REPAIR PARTS ILLUSTRATION FOR DC130010 AND DC200000

MAINTENANCE /

REPAIR

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

14

12

1

7

6

11

8

10

9

31

30

29

25

23

27

20

14

13

26

28

16

17

18

22

32

37

3

35

3

36

15

33

34

33

21

2

4

5

3

19

24

42

41

40

39

38

1

*

REPAIR PARTS LIST FOR DC130010 AND DC200000

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

15

Ref.

No. Description Part Number: Qty.

1 PUMP/MOTOR ASSEMBLY DC200101AV 1

2 M8 X 30 SCREW -- 4

3 M8 WASHER

■

8

4 LOCK NUT -- 4

5 RUBBER PAD -- 4

6 FRONT SHROUD -- 1

7 SIDE SHROUD BLACK -- 2

8 SIDE SHROUD GRAY -- 2

9 BACK SHROUD -- 1

10 M5 X 12 BOLT -- 6

11 ST3X12 TAPPING SCREW -- 8

12 ST4X18 TAPPING SCREW -- 8

13 QUICK COUPLER

▼

1

14 REGULATOR

▼

1

15 NPT 1/4 X 30 CONNECT

▼

1

16 NPT 1/8 PRESSURE GAUGE OUTLET

▼

1

17 NPT 1/4 PRESSURE GAUGE TANK

▼

1

18 PRESSURE SWITCH

▼

1

19 NPT 1/4 X 40 CONNECT

▼

1

20 SAFETY VALVE

▼

1

21 G1X8 RELIEF NUT

●

1

22 UNLOAD TUBE

DC200152AV ●

1

23 POWER CORD -- 1

24 CABLE CONNECTOR U -- 2

25 CABLE CONNECTOR O -- 1

26 TANK 13 GALLON HORIZONTAL

TANK 20 GALLON HORIZONTAL

--

1

27 CHECK VALVE DC200151AV 1

28 DRAIN VALVE DC200153AV 1

29 M6 X 30 HEXALE SCREW -- 2

30 HANDLE -- 1

31 HANDLE GRIP SR130011SV 1

32 BRASS COMPRESSION

▲

2

33 COMPRESSION NUT

▲

2

34 PRESSURE TUBE

▲

1

35 M8 X 30 BOLT

■

2

36 RUBBER FOOT

■

2

37 M8 NUT

■

2

38 AXLE

◆

2

39 6 IN. WHEEL

◆

2

40 M10 SPRING WASHER

◆

2

41 M10 NUT

◆

2

42 FILTER DC200150AV 2

REPAIR PARTS KITS

●

UNLOAD TUBE ASSEMBLY SR130012SV

■

RUBBER FOOT KIT SR130013SV

▲

EXHAUST TUBE KIT SR130014SV

▼

PRESSURE SWITCH/REGULATOR KIT SR130015SV

◆

TANK WHEEL KIT SR130016SV

For Repair Parts, visit www.campbellhausfeld.com

24 hours a day – 365 days a year

Please provide following information:

- Model number

- Serial number (if any)

- Part description and number as shown in parts list

REPAIR PARTS ILLUSTRATION FOR DC200101AV

MAINTENANCE /

REPAIR

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

16

1

3

4

11

18

19

21

22

24

23

5

6

7

8

9

10

12

13

7

2

14

15

16

20

17

27

26

25

28

2

29

30

31

32

28

33

34

45

46

43

42

41

26

40

38

39

37

36

35

44

*

REPAIR PARTS LIST FOR DC200101AV

MAINTENANCE /

REPAIR

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS

GETTING STARTED

17

Ref.

No. Description Part Number Qty.

1 M6X35 BOLT

●

4

2 SPRING WASHER

●

5

3 CYLINDER HEAD

●

1

4 O-RING FOR VALVE PLATE

UPPER

●

1

5 RELIEF VALVE

■

1

6 T-FITTING CONNECT

■

1

7 M4X8 SCREW

▲

2

8 M4 SPRING WASHER

▲

1

9 VALVE LIFT GUARD

▲

1

10 OUTLET VALVE

▲

1

11 VALVE PLATE

▲

1

12 INLET VALVE

▲

1

13 CAP OF INLET VALVE

▲

1

14 O-RING FOR VALVE PLATE

LOWER

▲ ▼

1

15 CYLINDER

▼

1

16 CRANKCASE -- 1

17 ECCENTRIC -- 1

18 M6X16 SCREW

▼

1

19 COVER OF CONROD

▼

1

20 PISTON RING

▼

1

21 CONROD

▼

1

22 FAN

◗

1

23 M6 WASHER

◗

1

24 M6X16 SCREW

◗

1

25 M5X25 SCREW

▼

1

26 M5 SPRING WASHER

▼

5

27 M5 NUT

▼

1

28 6203 BEARING -- 2

29 M6X40 SCREW -- 1

30 6204 BEARING -- 1

31 ROTOR -- 1

32 STATOR -- 1

33 WASHER -- 1

34 REAR MOTOR SEAT -- 1

35 M4X6 SCREW -- 1

36 M4 WASHER -- 1

37 GROUNDING SIGNAL -- 1

38 MOTOR FAN

◆

1

Ref.

No. Description Part Number Qty.

39 CIRCLI

◆

1

40 M5X10 BOLT -- 4

41 M3 SPRING WASHER -- 4

42 M3X6 SCREW -- 4

43 STARTING CAPACITOR

◆

1

44 RUNNING CAPACITOR

◆

1

45 M8 INNER WASHER

◆

2

46 M8 NUT

◆

10

REPAIR PARTS KITS

●

PUMP HEAD KIT DC200156AV

■

COLD START VALVE KIT DC200157AV

▲

VALVE PLATE KIT DC200158AV

▼

PISTON/CYLINDER KIT DC200159AV

◆

CAPACITOR KIT DC200160AV

◗

FRONT END FAN KIT DC200161AV

◆

MOTOR FAN KIT DC200162AV

18

Reminder: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

LIMITED WARRANTY

1. DURATION: From the date of purchase by the original purchaser as follows: One Year.

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld a Marmon/Berkshire Hathaway Company, 100 Production Drive,

Harrison, Ohio, 45030, Visit www.campbellhausfeld.com

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld

compressor.

4. WHAT PRODUCT IS COVERED BY THIS WARRANTY: This Campbell Hausfeld air compressor.

5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects due to material and workmanship with the exceptions noted below.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE

OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this compressor is used for commercial, industrial or rental purposes,

the warranty will apply for ninety (90) days from the date of purchase. Some States do not allow limitations on how long an

implied warranty lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE,

OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitations of incidental

or consequential damages, so the above limitation or exclusion may not apply to you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with

instructions provided in the owner’s manual(s) supplied with compressor.

D. Pre-delivery service, e.g. assembly, oil or lubricants, and adjustment.

E. Items or service that are normally required to maintain the product, e.g. lubricants, filters and gaskets, etc.

F. Gasoline engines and components are expressly excluded from coverage under this limited warranty. The Purchaser must comply

with the warranty given by the engine manufacturer which is supplied with the product.

G. Additional items not covered under this warranty:

1. All Compressors

a. Any component damaged in shipment or any failure caused by installing or operating unit under conditions not in

accordance with installation and operation guidelines or damaged by contact with tools or surroundings.

b. Pump or valve failure caused by rain, excessive humidity, corrosive environments or other contaminants.

c. Cosmetic defects that do not interfere with compressor functionality.

d. Electric motors, check valves and pressure switches.

e. Drain cocks.

f. Damage due to incorrect voltage or improper wiring.

g. Other items not listed but considered general wear parts.

h. Pressure switches, air governors and safety valves modified from factory settings.

2. Lubricated Compressors

a. Pump wear or valve damage caused by using oil not specified.

b. Pump wear or valve damage caused by any oil contamination or by failure to follow proper oil maintenance

guidelines.

3. Belt Drive / Direct Drive / Gas Driven Compressors

a. Belts.

b. Ring wear or valve damage from inadequate filter maintenance.

c. Manually adjusted load/unload and throttle control devices.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, compressor or component

which is defective, has malfunctioned and/or failed to conform within the duration of the specific warranty period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Portable compressors or components must be delivered or shipped to the nearest Campbell Hausfeld Authorized Service Center.

Freight costs, if any, must be borne by the purchaser.

C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled

and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.

This Limited Warranty applies in the U.S., Canada and Mexico only and gives you specific legal rights. You may also have other rights

which vary from State to State or country to country.

La page charge ...

Campbell Hausfeld DC200000 Manuel utilisateur

Campbell Hausfeld DC200000 Manuel utilisateur

dans d''autres langues

Documents connexes