POSMicro SP210 Manuel utilisateur

QUESTIONS?

Ask the experts at POSMicro.com.

1.800.241.6264

Live Chat Now

[email protected]

Monday - Friday 6 AM to 5 PM Pacic Time

BULK DISCOUNTS

FREE SHIPPING*

SE HABLA

ESPAñOL

*Free ground shipping to the continental USA on orders over $100.

For Help Call

1.800.241.6264

Star Micronics Manual

More information available at POSMicro.com

DOT MATRIX PRINTER

SP200F SERIES

USERS MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a

shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department

of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

CE

Manufacturer’s Declaration of Conformity

EC Council Directive 89/336/EEC of 3 May 1989

This product, has been designed and manufactured in accordance with the International

Standards EN 50081-1/01.92 and EN 50082-1/01.92, following the provisions of the

Electro Magnetic Compatibility Directive of the European Communities as of May 1989.

EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993

This product, has been designed and manufactured in accordance with the International

Standards EN 60950, following the provisions of the Low Voltage Directive of the

European Communities as of July 1993.

The above statement applies only to printers marketed in EU.

Trademark acknowledgments

SP200F Series: Star Micronics Co. Ltd.

VeriFone: VeriFone, Inc.

ESC/POS: Seiko Epson Corporation

Notice

without STAR’s express permission is forbidden.

• The contents of this manual are subject to change without notice.

• All efforts have been made to ensure the accuracy of the contents of this manual at the

time of going to press. However, should any errors be detected, STAR would greatly

appreciate being informed of them.

• The above notwithstanding, STAR can assume no responsibility for any errors in this

manual.

©

TABLE OF CONTENTS

1. Outline ...............................................................................................................1

2. Unpacking and Installation................................................................................2

2-1. Unpacking ..............................................................................................2

2-2. Locating the printer................................................................................3

2-3. Handling Care ........................................................................................3

2-4. Maintenance ...........................................................................................3

3. Parts Identification and Nomenclature ..............................................................4

4. Loading the Ribbon Cartridge and Paper ..........................................................6

4-1. SP210 type .............................................................................................6

4-2. SP240 type .............................................................................................9

4-3. Removing the Paper .............................................................................14

4-4. Connecting the Interface Cable............................................................14

5. Control Panel ...................................................................................................16

5-1. Basic Operation....................................................................................16

5-2. Switch Operation (Combined Switch Operation) ................................17

6. Control Codes ..................................................................................................19

STAR mode..................................................................................................19

6-1. Control Codes Used in Character Setting ............................................19

6-2. Control Codes Used in Print Mode Setting..........................................19

6-3. Control Codes Used in Line Spacing...................................................19

6-4. Control Codes Used for Peripheral Units ............................................20

6-5. Auto Cutter Control .............................................................................20

6-6. Other Control Codes ............................................................................20

Appendix A: Serial Interface...............................................................................87

A-1. Connectors and Signals........................................................................87

A-2. Interface Connections ..........................................................................88

A-3. Dip Switch Setting ...............................................................................89

A-4. Communication Protcol .......................................................................90

Appendix B: Parallel Interface ............................................................................92

B-1. Interface Specifications........................................................................92

B-2. Interface Timing...................................................................................92

B-3. Connectors and Signals........................................................................93

B-4. Dip Switch Setting ...............................................................................94

Appendix C: Peripheral Unit Drive Circuit.........................................................95

Appendix D: General Specifications ...................................................................97

Appendix E: Character Font Table....................................................................100

E-1. U.S.A..................................................................................................100

E-2. Europe ................................................................................................102

E-3. International Character Sets ...............................................................104

E-4. VeriFone ............................................................................................105

– 1 –

ENGLISH

1. Outline

The SP200 Series Serial Impact Dot Matrix Printer is designed for use with

electronic instruments such as POS, banking equipment, computer peripheral

equipment, etc.

The major features of the SP200 Series are as follows:

1. Bi-directional printing at approx. 2.5 lines/sec.

2. Serial interface or Parallel interface.

3. The data buffer allows the unit to receive print data even during printing.

4. Peripheral unit drive circuit enables control of external devices such as cash

drawers.

SP2 1 2 F D 42 – 120

Voltage

120 : 120VAC

230 : 230VAC

240 : 240VAC

No. of print columns

42 : 42 columns (16 CPI)

Interface

D : Serial interface (RS-232C)

K : Serial interface (RS-422A)

C : Parallel interface

Paper feed

F : Friction paper feed method

Mechanism

2 : Single color, 42 columns (16 CPI)

6 : Two color, 42 columns (16 CPI)

Printer type

1 : Standard type

4 : Auto cutter equipped type

SP200 Series printer

– 2 –

ENGLISH

2. Unpacking and Installation

2-1. Unpacking

After unpacking the unit, check that all the necessary accessories are included in

the package.

SP210 type

SP240 type

Fig. 2-1 Unpacking

User´s manual

Ribbon cartridge

Printer

Ferrite core

(EU only)

Fastener

(EU only)

Printer

User´s manual

Ribbon cartridge

Ferrite core

(EU only)

Fastener

(EU only)

– 3 –

ENGLISH

2-2. Locating the printer

When you locate your printer, keep the following tips in mind:

1. Protect your printer from excessive heat such as direct sunlight or heaters, and

keep it away from moisture and dust.

2. Place the printer on a firm, level surface which is fairly vibration-free.

3. A steady power supply that is not subject to power surges should be connected

to the printer.

For example, do not connect it to the same circuit as a large, noise-producing

appliance such as a refrigerator or an air conditioner.

4. Make sure the line voltage is the voltage specified on the printer’s identifica-

tion plate.

5. To disconnect the printer, the plug has to be disconnected from the wall socket,

which has to be located close to the printer, and easy to access.

2-3. Handling Care

1. Be careful not to drop paper clips, pins or other foreign matter into the unit as

these cause the printer to malfunction.

2. Do not attempt to print when either paper or ribbon cartridge is not located in

the printer, otherwise the print head can be damaged.

3. Do not open the cover while printing.

4. Do not touch the print head immediately after printing as it gets very hot.

5. Use only roll paper that is not glued to the core.

6. When the paper end mark appears on the paper, replace the roll paper before

it runs out.

2-4. Maintenance

Essentially, your printer is a robust piece of equipment, but should be treated with

a modicum of care in order to avoid malfunctions. For example:

1. Keep your printer in a “comfortable” environment. Roughly speaking, if you

feel comfortable, then the environment is suitable for your printer.

2. Do not subject the printer to physical shocks or excessive vibration.

3. Avoid over-dusty environments. Dust is the enemy of all precision mechani-

cal devices.

4. To clean the exterior of the printer, use a cloth barely dampened with either

water with a little detergent or a little alcohol, but do not allow any liquid to

fall inside the printer.

5. The interior of the printer may be cleaned with a small cleaner or a com-

pressed-air aerosol (sold for this purpose). When performing this operation,

be sure not to bend or damage any cable connections or electronic compo-

nents.

– 4 –

ENGLISH

3. Parts Identification and Nomenclature

SP210 type

Fig. 3-1 External view of the printer (SP210 type)

Features two control

switches and two

indicators to indicate

printer status.

Control panel

Protects the printer from

dust and reduces noise.

Do not open the cover

while printing.

Cover

Connects the printer

with host computer.

Interface connector

Connects to peripheral units such

as cash drawers, etc.

Do not connect this to a telephone.

Peripheral unit drive circuit connector

Plugs into an outlet of

the specified voltage.

Shape of AC power plug

will vary according to

destinations.

AC power cord

– 5 –

ENGLISH

SP240 type

Fig. 3-2 External view of the printer (SP240 type)

Features two control

switches and two

indicators to indicate

printer status.

Control panel

Connects the printer

with host computer.

Interface connector

Connects to peripheral units such

as cash drawers, etc.

Do not connect this to a telephone.

Peripheral unit drive circuit connector

Protects the printer from

dust and reduces noise.

Do not open the cover

while printing.

Cover

Plugs into an outlet of

the specified voltage.

Shape of AC power plug

will vary according to

destinations.

AC power cord

– 6 –

ENGLISH

4. Loading the Ribbon Cartridge and Paper

4-1. SP210 type

4-1-1.Loading the Ribbon Cartridge

1 Turn off power to the printer.

2 Lift the cover up approx. 3 cm.

Hold the cover tilted at this an-

gle, then pull it toward you to

remove it.

3 Place the ribbon cartridge in the

direction shown in Fig. 4-2 and

press it down to load it. If loading

of the ribbon cartridge is not sat-

isfactory, press down the car-

tridge while rotating the ribbon

feed knob in the direction of the

arrow.

4 Turn the ribbon feed knob of the

ribbon cartridge in the direction

of the arrow to remove slack in

the ribbon.

5 Mount the cover by reversing the

procedure outlined in step 2

above.

Fig. 4-1 Removing the cover

Cover

Power off

Print head

Ink ribbon

Ribbon cartridge

Ribbon feed

knob

Notched

part

Fig. 4-2 Loading the ribbon cartridge

– 7 –

ENGLISH

Note: When removing the ribbon car-

tridge, raise the A section and

then remove it by holding the B

section as shown in Fig. 4-3.

A

B

Fig. 4-3

4-1-2.Loading the Paper

1 Lift the cover up approx. 3cm. Hold

the cover tilted at this angle, then

pull it toward you to remove it.

Cover

FEED

switch

Fig. 4-4 Removing the cover

– 8 –

ENGLISH

2 Cut off the front edge of the roll

paper perpendicularly.

3 Confirm that the power of the printer

is turned on.

4 While observing the direction of the

roll paper, insert the top end of the

paper beneath the paper guide as far as

it will go. If the roll paper is installed,

the top end of the paper automatically

comes out from the paper exit.

5 Move the paper roll holder in the

direction of the arrow, and insert the

roll so that the holes in the core align

with the axes of the paper roll holder.

Release the paper roll holder to se-

cure the paper.

6 If the paper roll core has not been

properly aligned with the paper roll

holder, the cover cannot to properly

seated until the paper position is

corrected.

7 Press the FEED (paper feed) switch to

feed the paper approximately 10cm.

8 Insert the top edge of the paper into

the tear bar slot, then mount the cover

by reversing the procedure for re-

moving the cover in step 1 above.

Note: When the paper end mark ap-

pears on the paper, replace the

roll paper before it runs out.

Fig. 4-7

Positioning rib

Cover

Roll paper

Paper roll holder

Roll paper

Core

Axis

Paper roll holder

Fig. 4-5 Loading the paper

Fig. 4-6

FEED switch

Tear bar

– 9 –

ENGLISH

4-2. SP240 type

4-2-1.Loading the Ribbon Cartridge

1 Turn off power to the printer.

2 Lift the cover up approx. 3 cm.

Hold the cover tilted at this an-

gle, then pull it toward you to

remove it.

3 Lift up the auto cutter and put it in

a vertical position, as shown in

Fig. 4-9.

Cove

r

Power off

Fig. 4-8 Removing the cover

Auto cutter

Fig. 4-9 Raise the auto cutter

– 10 –

ENGLISH

4 Place the ribbon cartridge in the

direction shown in Fig. 4-10 and

press it down to load it. If loading

of the ribbon cartridge is not sat-

isfactory, press down the car-

tridge while rotating the ribbon

feed knob in the direction of the

arrow.

5 Turn the ribbon feed knob of the

ribbon cartridge in the direction

of the arrow to remove slack in

the ribbon.

6 Close the Auto Cutter.

7 Mount the cover by reversing the

procedure outlined in step 2

above.

Note: When removing the rib-

bon cartridge, raise the A

section and then remove

it by holding the B section

as shown in Fig. 4-11.

Fig. 4-10 Loading the ribbon cartridge

Print head

Ink ribbon

Auto cutter

Ribbon cartridge

Ribbon feed

knob

Notched

part

A

B

Fig. 4-11

– 11 –

ENGLISH

4-2-2.Loading the Paper

1 Lift the cover up approx. 3cm. Hold

the cover tilted at this angle, then

pull it toward you to remove it.

2 Cut off the front edge of the roll

paper perpendicularly.

3 Confirm that the power of the printer

is turned on.

4 While observing the direction of the

roll paper, insert the top end of the

paper beneath the paper guide as far as

it will go. If the roll paper is installed,

the top end of the paper automatically

comes out from the paper exit. After

2cm of paper are fed out, the paper

is automatically cut off.

5 Move the paper roll holder in the

direction of the arrow, and insert the

roll so that the holes in the core align

with the axes of the paper roll holder.

Release the paper roll holder to se-

cure the paper.

6 If the paper roll core has not been

properly aligned with the paper roll

holder, the cover cannot to properly

seated until the paper position is

corrected.

Cover

FEED

switch

Fig. 4-12 Removing the cover

Roll paper

Core

Axis

Paper roll holder

Fig. 4-13 Loading the paper

– 12 –

ENGLISH

7 Press the FEED (paper feed) switch

to feed the paper approximately

10cm.

8 Insert the tip of the roll paper in the

auto cutter paper slit.

• When using copying paper, insert

only the original (the upper paper)

into the slit of the auto cutter. Insert

the paper which is to be copied (the

lower paper) between the platen and

the auto cutter.

Fig. 4-14

Positioning rib

Cover

Roll paper

Paper roll holder

Paper

insertion

slit

Auto

cutter

Fig. 4-15 Insertion of the paper into

the auto cutter

– 13 –

ENGLISH

Fig. 4-16 Insertion of the paper into the auto cutter

(When using copying paper)

9 Pull on the edge of the paper to

remove any slack and then lower the

auto cutter.

0 Insert the paper through the paper

outlet and then replace the cover by

reversing the removal steps.

Note: When the paper end mark ap-

pears on the paper, replace the

roll paper before it runs out.

Fig. 4-18

Paper

outlet

Auto cutter

Fig. 4-17 Paper outlet of the front

cover

Paper insertion

slit

Platen

Lower paper

Upper

paper

Print head

Paper insertion

slit

Auto cutter

Platen

Lower paper

Upper paper

FEED switch

– 14 –

ENGLISH

4-3. Removing the Paper

Remove the cover, then cut off the paper near the rear of the paper guide and press

the FEED switch to feed out the paper remaining in the unit.

When the paper runs out, the POWER lamp will blink.

Note 1. Remove the paper remaining in the printer by pressing the FEED

switch.

2. When the paper end mark appears on the paper, replace the roll

paper before it runs out.

3. When removing the core of the roll paper, open the roll paper

holder.

4-4. Connecting the Interface Cable

4-4-1.Ferrite core installation (EU only)

1 Affix the ferrite core onto the serial/

parallel interface cable as shown in

the illustration.

If a ferrite core is not open, use a

screw driver to pry it apart, taking

care not to damage the core or lock.

2 Pass fastener through ferrite core.

3 Pass fastener around cable and lock

it.

Cut off excess with scissors.

Attach the ferrite core only to the

cables of printers sold in the EU.

Ferrite core

Interface cable

Fig. 4-19

Pull and cut

5cm

maximum

Fastener

– 15 –

ENGLISH

4-4-2.Serial Interface Cable

1 Turn off power to both the host

computer and the printer.

2 Insert the connector at one end of

the interface cable into the connec-

tor on the printer and the other con-

nector into the connector for the

host computer.

3 Next, fasten the right and left screws

for the respective interface connec-

tors to fix them in place on the

connectors.

Ferrite core

(EU only)

Screwdriver

Screws

Fig. 4-20 Connecting the interface

cable

4-4-3.Parallel Interface Cable

1 Turn off power to both the host

computer and the printer.

2 Insert one terminal of the interface

cable into the printer’s connector,

as shown in the diagram, and fasten

it there with the clasp.

3 Insert the other terminal of interface

cable into the host computer’s con-

nector, and again fasten it with the

clasp.

Fig. 4-21 Connecting the parallel

interface cable

Ferrite core

(EU only)

– 16 –

ENGLISH

5. Control Panel

5-1. Basic Operation

1 ON LINE switch

Switches the printer between ON

LINE and OFF LINE. ON LINE

and OFF LINE switching is possi-

ble only when paper is loaded in the

printer.

2 FEED switch

• When this switch is pressed and

then released within 0.5 sec., the

paper feeds on line.

• When this switch is held depressed

for more than 0.5 sec., the paper

feeds continuously.

(The above paper feed operation is

possible for both ON LINE and OFF

LINE modes.)

3 POWER lamp (green LED)

• Lights when the power to the printer is on.

• Flashes when paper is out, mechanical error occurs, when there is an alarm due

to head temperature detection, or when a CPU error has occurred.

• If the paper is out, load new paper and press the ON LINE switch.

• When the POWER lamp flashes due to occurrence of a mechanical error, turn

off the power and remove the cause of a mechanical error and then turn on the

power again to reset the printer.

• If the POWER lamp flashes due to the alarm of the head temperature detection,

the printer will be set automatically when the head temperature becomes low.

4 ON LINE lamp (green LED)

LED lit: Printer is ON LINE

LED off: Printer is OFF LINE

LED flashes: CPU error

When the POWER lamp and ON LINE lamp light simultaneously, a CPU

error has occurred.

ON LINEPOWER FEED

3 4 1 2

Fig. 5-1 Control panel

La page charge ...

POSMicro SP210 Manuel utilisateur

Ce manuel convient également à

POSMicro SP210 Manuel utilisateur

dans d''autres langues

Autres documents