STIHL MS 462 C-M Manuel utilisateur

Marque: STIHL

Modèle: MS 462 C-M

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

STIHL MS 462 C-M

Instruction Manual

Notice d’emploi

G Instruction Manual

1 - 66

F Notice d’emploi

67 - 143

Original Instruction ManualPrinted on chlorine-free paper

Printing inks contain vegetable oils, paper can be recycled.

0458-790-8221-A. VA3.M19.

0000008350_003_GB

0458-790-8221-A

English

with electronic systems.

Contents

1 Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Guide to Using this Manual

. . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Signal Words

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Symbols in Text

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 Main Parts

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1 Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2 Features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Safety Symbols on the Product

. . . . . . . . . . . . . . . . . . . . . .

4.1 Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 IMPORTANT SAFETY INSTRUCTIONS

. . . . . . . . . . . . .

5.1 Intended Use

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 Operator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 Personal Protective Equipment

. . . . . . . . . . . . . . . . . . . . . .

5.4 Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5 Fueling Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6 Using the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 Kickback and Other Reactive Forces

. . . . . . . . . . . . . . .

6.1 Reactive Forces

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2 Kickback

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3 Pull-in

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.4 Pushback

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 Proper Techniques for Basic Bucking, Limbing,

Pruning and Felling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.1 Bucking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2 Cutting Logs Under Tension

. . . . . . . . . . . . . . . . . . . . . . . .

7.3 Limbing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.4 Pruning

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.5 Felling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 Maintenance, Repair and Storage

. . . . . . . . . . . . . . . . . .

8.1 Warnings and Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . .

9 Before Starting Work

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1 Preparing the Chain Saw for Operation

. . . . . . . . . . . . .

10 Assembling the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . .

10.1 Cutting Attachment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.2 Mounting and Removing the Guide Bar and

Chain

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.3 Tensioning the Chain

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 Lubricating the Saw Chain and Guide Bar

. . . . . . . . . .

11.1 Bar and Chain Lubricant

. . . . . . . . . . . . . . . . . . . . . . . . . . .

11.2 Filling the Chain Oil Tank

. . . . . . . . . . . . . . . . . . . . . . . . . .

11.3 Adjusting the Flow of Bar and Chain Oil

. . . . . . . . . . . .

12 The Chain Brake

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.1 Engaging the Chain Brake

. . . . . . . . . . . . . . . . . . . . . . . . .

12.2 Disengaging the Chain Brake

. . . . . . . . . . . . . . . . . . . . . .

12.3 Maintaining the Chain Brake

. . . . . . . . . . . . . . . . . . . . . . .

13 Mixing Fuel and Refueling the Chain Saw

. . . . . . . . . .

13.1 Mixing Fuel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.2 Refueling the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . .

14 Starting the Engine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.1 Holding the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.2 Starting the Engine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 Shutting Off the Engine

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

15.1 Shutting Off the Engine

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

16 Checking the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . .

16.1 Checking the Operation of the Chain Brake

. . . . . . . .

16.2 Testing the Controls

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.3 Testing Chain Lubrication

. . . . . . . . . . . . . . . . . . . . . . . . . .

17 Adjusting the Carburetor

. . . . . . . . . . . . . . . . . . . . . . . . . . .

17.1 STIHL M-Tronic Engine Management System

. . . . . .

17.2 Calibrating the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . .

17.3 Winter Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17.4 Summer Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 After Finishing Work

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.1 Preparing for Transportation or Storage

. . . . . . . . . . . .

19 Transporting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19.1 Transporting the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . .

0458-790-8221-A

English

1 Introduction

Thank you for your purchase. The information contained in

this manual will help you receive maximum performance and

satisfaction from your STIHL chain saw and, if followed,

reduce the risk of injury from its use.

SAVE THIS MANUAL!

Have your authorized STIHL servicing dealer show you how

to operate your chain saw. All safety precautions that are

generally observed when working with an axe or a hand saw

also apply to the operation of chain saws. Observe all

applicable federal, state and local safety regulations,

standards and ordinances.

Do not lend or rent your chain saw without this instruction

manual. Allow only persons who have the proper training

and fully understand the information in this manual to

operate the chain saw.

For further information, or if you do not understand any of

the instructions in this manual, please go to www.stihl.ca or

contact your authorized STIHL servicing dealer.

2.1 Signal Words

This manual contains safety information that requires your

special attention. Such information is introduced with the

following symbols and signal words:

20 Storing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20.1 Storing the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 Cleaning

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21.1 Cleaning the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . . . .

21.2 Cleaning the Guide Bar and Saw Chain

. . . . . . . . . . . .

21.3 Cleaning the Air Filter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21.4 Cleaning the Spark Plug

. . . . . . . . . . . . . . . . . . . . . . . . . . .

22 Inspection and Maintenance

. . . . . . . . . . . . . . . . . . . . . . . .

22.1 Inspection and Maintenance Chart

. . . . . . . . . . . . . . . . .

22.2 Inspecting and Maintaining the Chain Saw

. . . . . . . . .

22.3 Inspecting and Maintaining the Chain Sprocket

. . . . .

22.4 Inspecting and Maintaining the Guide Bar

. . . . . . . . . .

22.5 Inspecting, Maintaining and Sharpening the Saw

Chain

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 Troubleshooting Guide

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23.1 Chain saw

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23.2 Clearing the Combustion Chamber

. . . . . . . . . . . . . . . . .

24 Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24.1 CEPA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24.2 STIHL MS 462 C-M

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24.3 Chain Sprockets

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24.4 Minimum Groove Depth of Guide Bars

. . . . . . . . . . . . .

24.5 Depth Gauge Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24.6 Symbols on the Chain Saw

. . . . . . . . . . . . . . . . . . . . . . . . .

24.7 Engineering Improvements

. . . . . . . . . . . . . . . . . . . . . . . . .

25 CSA Standard

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25.1 Chain Saw Class

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25.2 Definition of the Chain Saw Classes according to

CSA Z62.1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 Combinations of Guide Bars and Saw Chains

. . . . . .

26.1 STIHL MS 462 C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27 Replacement Parts and Equipment

. . . . . . . . . . . . . . . . .

27.1 Genuine STIHL Replacement Parts

. . . . . . . . . . . . . . . .

28 Disposal

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28.1 Disposal of the Power Tool

. . . . . . . . . . . . . . . . . . . . . . . . .

29 Emission Control Warranty

. . . . . . . . . . . . . . . . . . . . . . . . .

29.1 STIHL Limited Federal Emission Control

Warranty Statement

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 Introduction

Because a chain saw is a high-speed wood-

cutting tool, special safety precautions must be

observed to reduce the risk of personal injury.

Read this instruction manual thoroughly before

use and periodically thereafter. Follow all safety

precautions. Careless or improper use of the

chain saw can cause serious or fatal injury.

2 Guide to Using this Manual

0458-790-8221-A

English

3 Main Parts

DANGER

Indicates a hazardous situation that, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazardous situation that, if not avoided, could

result in death or serious injury.

NOTICE

Indicates a risk of property damage, including damage to the

machine or its individual components.

2.2 Symbols in Text

The following symbol is included to assist you with the use

of the manual:

3.1 Chain Saw

Refers to a designated chapter or sub-chapter in this

instruction manual.

3 Main Parts

0000-GXX-3166-A0

0458-790-8221-A

English

3 Main Parts

1 Front Hand Guard

Helps protect the operator's left hand from projecting

branches and contact with the saw chain. Serves as the

activation lever for the chain brake.

2 Muffler with Spark Arresting Screen

Reduces engine exhaust noise and diverts exhaust

gases away from the operator. The spark arresting

screen is designed to reduce the risk of fire.

3Bumper Spike

Helps hold the saw steady against the wood during

cutting.

4 Saw Chain

Toothed cutting tool consisting of cutters, tie straps and

drive links.

5 Guide Bar

Supports and guides the saw chain.

6 Chain Catcher

Helps contain the saw chain and reduce the risk of

operator contact in the event the chain breaks or comes

off the bar.

7 Side Chain Tensioner

Permits precise adjustment of saw chain tension.

8 Chain Sprocket

Drives the saw chain.

9 Chain Sprocket Cover

Covers the chain sprocket.

10 Nuts

Tighten the chain sprocket cover to the chain saw.

11 Shroud

Covers the air filter and engine.

12 Shroud Lock

Lock for the shroud.

13 Front Handle

Handle for the operator's left hand.

14 Decompression Valve (not available on all models)

Makes starting easier.

15 Spark Plug

Ignites the fuel-air mix in the engine.

16 Shutter for Summer or Winter Operation

With summer and winter positions. Carburetor is heated

in winter position.

17 Spark Plug Boot

Connects the spark plug with the ignition lead.

18 Air Filter

Filters the air drawn into the engine.

19 Throttle Trigger Lockout

Prevents activation of the throttle trigger until depressed.

20 Rear Handle

Handle for the operator's right hand.

21 Rear Hand Guard

Helps protect the operator's right hand in the event the

chain breaks or comes off the bar.

22 Throttle Trigger

Controls the speed of the engine.

23 Master Control Lever

Lever for choke control, starting throttle, run and stop

switch position.

24 Fuel Filler Cap

Closes and seals the fuel tank.

25 Starter Grip

The grip of the pull starter for starting the engine.

26 Oil Flow Adjusting Screw

For adjusting the amount of chain oil.

27 Oil Adjustment Limiter

Limits travel of oil flow adjusting screw.

28 Oil Filler Cap

Closes and seals the oil tank.

29 Chain Scabbard

Covers the guide bar and saw chain to reduce the risk of

injury from inadvertent contact during transportation and

storage.

0458-790-8221-A

English

4 Safety Symbols on the Product

Clutch (not illustrated)

Engages the chain sprocket when the engine is

accelerated beyond idle speed.

Anti-Vibration System (not illustrated)

The anti-vibration system includes a number of anti-

vibration elements designed to reduce the transmission

of vibration created by the engine and cutting attachment

to the operator's hands.

# Rating Plate

Contains the product's serial number.

3.2 Features

The chainsaw may be equipped with the following features:

1 Handle Heating Switch

Switches the handle heating on and off.

Carburetor heating (not illustrated)

Heats the carburetor when the engine is running. Saws

with a handle heating system also have carburetor

heating.

4.1 Chain Saw

The following safety symbols are found on the chain saw:

5.1 Intended Use

WARNING

￭ This chain saw is designed for cutting trees, branches and

limbs. Use of the chain saw for operations different than

intended could result in serious injury or death.

– Cut wood only. For example, do not use chain saw

for cutting metal, plastic or masonry.

– Read and follow the operating and use instructions

in this manual for approved applications and

recommended working techniques.

￭ The saw chain has many sharp cutters. If they contact

your flesh, they will cut you even if the chain is not moving.

– Always wear heavy-duty work gloves when handling

the saw or its chain.

– Keep hands, feet and other parts of your body away

from the chain.

4 Safety Symbols on the Product

0000-GXX-3167-A0

To reduce the risk of injury, follow the specified

safety precautions.

Read and follow all safety precautions in the

instruction manual. Improper use can lead to

serious or fatal personal injury or property

damage.

To reduce the risk of serious personal injury and

hearing loss, always wear proper eye protection,

hearing protection and an approved protective

helmet, @ 5.3.

Avoid contact of the bar tip with any object. This

can cause the bar to kick suddenly up and back,

which may result in serious or fatal injury. Always

use two hands to operate the saw, @ 6.

5 IMPORTANT SAFETY

INSTRUCTIONS

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

￭ Reactive forces, including kickback, can be dangerous.

– Pay special attention to the sections of this

instruction manual dealing with reactive forces.

￭ Observe all applicable federal, state and local safety

regulations, standards and ordinances.

￭ Improper use could result in personal injury or property

damage, including damage to the chain saw.

– Use the chain saw only as described in this manual.

– Never attempt to modify or override the chain saw's

controls or safety devices in any way.

– Never use a chain saw that has been modified or

altered from its original design.

5.2 Operator

WARNING

￭ Working with the chain saw can be strenuous. The

operator must be in good physical condition and mental

health. To reduce the risk of personal injury from fatigue

and loss of control:

– Check with your doctor before using the chain saw if

you have any health condition that may be

aggravated by strenuous work.

– Do not operate the chain saw while under the

influence of any substance (drug, alcohol or

medication, etc.) that might impair vision, balance,

dexterity or judgment.

– Be alert. Do not operate the chain saw when you are

tired. Take a break if you become tired.

– Do not permit minors to use the chain saw.

– Bystanders, especially children, and animals should

not be allowed in the area where the chain saw is in

use.

￭ Prolonged use of a chain saw (or other power tools)

exposing the operator to vibration may produce white

finger disease (Raynaud's phenomenon) or carpal tunnel

syndrome. These conditions reduce the hand's ability to

feel and regulate temperature. They produce numbness

and burning sensations and may also cause nerve and

circulation damage as well as tissue necrosis.

￭ All factors which contribute to white finger disease are not

known. Cold weather, smoking and diseases or physical

conditions that affect blood vessels and blood transport,

as well as high vibration levels and long periods of

exposure to vibration, are mentioned as factors in the

development of white finger disease.

￭ STIHL chain saws are equipped with an anti-vibration

("AV") system designed to reduce the transmission of

vibration from the saw to the operator's hands. To reduce

the risk of white finger disease and carpal tunnel

syndrome:

– Wear gloves while working and keep your hands

warm.

– Keep the chain saw and its AV system well

maintained. A chain saw with loose components or

with damaged or worn AV elements will tend to have

higher vibration levels.

– Keep the saw chain sharp. A dull chain will increase

cutting time, and pressing a dull chain through wood

will increase the vibration transmitted to your hands.

– Maintain a firm grip at all times, but do not squeeze

the handles with constant, excessive pressure. Take

frequent breaks.

￭ These precautions do not guarantee that you will not

sustain white finger disease or carpal tunnel syndrome.

– Closely monitor the condition of your hands and

fingers if you are a regular operator.

– Seek medical advice immediately if any of the above

symptoms appear.

￭ The ignition system of this machine produces an

electromagnetic field of a very low intensity. This field may

interfere with some pacemakers or implanted medical

devices. To reduce the risk of injury:

– Persons with a pacemaker or other implanted

medical device should consult their physician and

the device manufacturer before operating this chain

saw.

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

5.3 Personal Protective Equipment

WARNING

￭ To reduce the risk of personal injury:

– Always wear proper clothing and protective apparel,

including proper eye protection.

￭ Loss of control and severe cut injuries may result if hair,

clothing or apparel make contact with the moving saw

chain or otherwise become entangled in the components

of the saw. To reduce the risk of severe personal injury:

– Wear a long-sleeve shirt or jacket.

– Avoid loose-fitting jackets, scarves, neckties, flared

or cuffed pants, jewelry and any other apparel that

could be caught on branches, brush or the moving

chain.

– Secure hair above shoulder level before starting

work.

￭ To reduce the risk of eye injury:

– To reduce the risk of injury to your face, STIHL

recommends that you also wear a face shield or face

screen over your goggles or protective glasses.

￭ To reduce the risk of head injury from falling branches or

other objects encountered during work:

– Wear an approved protective helmet.

￭ Prolonged exposure to power tool noise may result in

permanent hearing damage. To reduce the risk of hearing

damage:

￭ Good footing is very important. To help maintain a secure

footing and reduce the risk of injury while working:

￭ To improve your grip and help protect your hands:

5.4 Chain Saw

WARNING

￭ The saw chain has many sharp cutters. Contacting the

cutters may result in serious laceration injuries, even if the

chain is not moving. To reduce the risk of such injuries:

– Keep hands, feet and other parts of your body away

from the chain.

– Wear heavy-duty work gloves when handling the

chain saw or its chain.

– Never touch a moving chain with your hand or any

other part of your body.

– Cover the guide bar with a chain scabbard before

transporting or storing the chain saw to reduce the

risk of injury from inadvertent contact.

– Wear sturdy and snug-fitting clothing that

also allows complete freedom of

movement.

– Wear the type of overalls, long pants or

chaps that contain pads of cut-retardant

material.

– Always wear goggles or close-fitting

protective glasses with adequate top and

side protection that are impact-rated and

marked as complying with CSA Z94.

– Wear sound barriers (ear plugs or ear

muffs).

– Regular operators should have their

hearing checked periodically.

– Be particularly alert and cautious when

using hearing protection. Your ability to

hear shouts, alarms or other audible

warnings is restricted.

– Wear sturdy boots with non-slip soles.

Steel-toed safety boots are

recommended. Do not wear sandals, flip-

flops, open-toed or similar footwear.

– Always wear heavy-duty non-slip work

gloves made of leather or another wear-

resistant material when handling the

chain saw or its chain.

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

￭ Reactive forces, including kickback, can be dangerous.

– Pay special attention to the section of this instruction

manual on "Kickback and Other Reactive Forces,"

@ 6.

￭ To reduce the risk of personal injury to the operator and

bystanders:

– Always release the throttle trigger, engage the chain

brake and shut off the engine before assembling,

transporting, adjusting, inspecting, cleaning,

servicing, maintaining or storing the chain saw.

– Shut off the chain saw anytime it is not in use.

￭ To reduce the risk of fire and explosion:

– Only use the spark plug specified in this instruction

manual and make sure it and the ignition lead are

clean and in good condition.

– Always press the spark plug boot snugly onto the

spark plug terminal of the proper size.

– Never test the ignition system with the spark plug

boot removed from the spark plug or with a removed

spark plug.

￭ Although certain unauthorized attachments may fit your

STIHL chain saw, their use may be extremely dangerous.

Only attachments supplied by STIHL or expressly

approved by STIHL for use with this specific model are

recommended.

– Use only attachments supplied or expressly

approved by STIHL.

– Never modify this chain saw in any way.

– Never attempt to modify or override the chain saw's

controls or safety devices in any way.

– Never use a chain saw that has been modified or

altered from its original design.

￭ Any modification to your muffler or spark arresting screen

could cause an increase in heat radiation, sparks or sound

level, thereby increasing the risk of fire, burn injury or

hearing loss. You may also permanently damage the

engine.

– Never modify your muffler or spark arresting screen.

￭ If the chain saw is dropped or subjected to similar heavy

impacts:

– Check that it is undamaged, in good condition and

functioning properly before continuing work.

– Check that the fuel system is tight and has no leaks.

– Check that the controls and safety devices, including

the chain brake, are working properly, @ 16.

– Never work with a damaged or malfunctioning chain

saw. In case of doubt, have the chain saw checked

by your authorized STIHL servicing dealer.

￭ Genuine STIHL replacement parts are specifically

designed to match your chain saw and meet safety and

performance requirements. Use of parts that are not

authorized or approved by STIHL may cause serious or

fatal injury or property damage.

– STIHL recommends that only identical STIHL

replacement parts be used.

5.5 Fueling Instructions

Fuel

WARNING

￭ Gasoline and its vapors are extremely flammable. Your

STIHL chain saw uses an oil-gasoline mixture for fuel. If

spilled and ignited by a spark or other ignition source, it

can cause fire and serious burn injury or property damage.

– Use extreme caution when handling

gasoline or fuel mix.

– Do not smoke or bring any fire or flame

near the fuel or the chain saw.

– Note that combustible fuel vapor may

escape from the fuel system.

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

Pick a Safe Location for Fueling

WARNING

￭ To reduce the risk of fire and explosion while fueling:

Allow the Saw to Cool Before Removing the Fuel Cap

WARNING

￭ Gasoline vapor pressure may build up inside the fuel tank.

The amount of pressure depends on a number of factors,

such as the fuel used, altitude, and temperature. To

reduce the risk of burns and other personal injury from

escaping gas, vapor and fumes:

– Always shut off the engine and allow it to cool before

removing the fuel cap.

￭ The engine is air cooled. When it is shut off, cooling air is

no longer drawn across the cylinder and engine

temperatures will rise for several minutes before starting

to cool. In hot environments, cooling will take longer. To

reduce the risk of burns and other personal injury from

escaping gas vapor and fumes:

– Allow the chain saw to cool. If you need to refuel

before completing a job, turn off the machine and

allow the engine to cool before opening the fuel tank.

Fuel Spraying or "Geysering"

WARNING

￭ Removing the cap on a pressurized fuel tank can result in

gasoline, vapors and fumes being forcefully sprayed out

from the fuel tank in all directions. The escaping gasoline,

vapors or fumes can cause serious personal injury,

including fire and burn injury, or property damage.

￭ Sometimes also referred to as “fuel geysering,” fuel

spraying is an expulsion of fuel, vapors and fumes which

can occur in hot conditions, or when the engine is hot, and

the tank is opened without allowing the saw to cool

adequately. It is more likely to occur when the fuel tank is

half full or more.

￭ Pressure is caused by fuel and heat and can occur even if

the engine has not been running. When gasoline in the

fuel tank is heated (by ambient temperatures, heat from

the engine, or other sources), vapor pressure will increase

inside the fuel tank.

￭ Some blends of gasoline, particularly winter blends, may

cause tanks to pressurize more quickly or create greater

pressure. At higher altitudes, fuel tank pressurization is

more likely.

How to Avoid Fuel Spraying

WARNING

￭ Removing the fuel cap on a pressurized tank can result in

gasoline, vapors and fumes being forcefully sprayed out

from the fuel tank in all directions. To reduce the risk of

burns, serious injuries or property damage from fuel

spraying:

– Follow the fueling instructions in this chapter.

– Always assume your fuel tank is pressurized.

– Allow the chain saw to cool before removing the fuel

cap.

– If you need to refuel before completing a job, turn off

the machine and allow the engine to cool before

removing the fuel cap.

– In hot environments, cooling will take longer.

– Fuel your chain saw in a well-ventilated

area, outdoors away from flames, pilot

lights, heaters, electric motors, and other

sources of ignition. Vapors can be

ignited by a spark or flame many feet

away.

– Select bare ground for fueling and move

at least 10 ft. (3 m) from the fueling spot

before starting the engine.

– Wipe off any spilled fuel before starting

your chain saw.

– Take care not to get fuel on your

clothing. If this happens, change your

clothing immediately.

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

– The engine is air cooled. When it is shut off, cooling

air is no longer drawn across the cylinder and the

engine temperature will rise for several minutes

before starting to cool.

￭ After the chain saw has cooled appropriately, follow the

safety instructions in this chapter for removing the cap.

– Never remove the cap by turning it directly to the

open position.

– First check for residual pressure by turning the cap

slowly to the vent position, approximately 1/8 turn

counter-clockwise.

– Use only good quality fuel that is appropriate for the

season (summer v. winter blends). Some blends of

gasoline, particularly winter blends, are more volatile

and can contribute to fuel spraying.

Removing the Toolless Fuel Cap: Turn Slowly and Stop in

the Vent Position

WARNING

￭

￭ After allowing the chain saw to cool, remove the fuel filler

cap slowly and carefully to allow any remaining pressure

build-up in the tank to release:

– Flip up the grip and press the cap down firmly (1).

– While maintaining steady, downward pressure, turn

the cap slowly counter-clockwise to the vent

position (2), approximately a 1/8 turn of the cap.

– If any significant venting occurs, immediately re-seal

the tank by turning the cap clockwise to the closed

position. Allow the saw to cool further before

attempting to open the tank.

– Turn the cap to the open position (3) only after the

contents of the tank are no longer under pressure. In

the open position, the exterior positioning mark (4)

on the cap will line up with the "unlocked" symbol (5)

on the fuel tank housing.

– Never remove the cap by turning it directly to the

open position without first allowing the saw to cool

adequately and then letting it release any residual

pressure at the vent position (2).

– Never attempt to remove the cap while the engine is

still hot or running.

Installing the Toolless Fuel Cap

WARNING

￭

0000-GXX-2144-A0

123

0000-GXX-2935-A1

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

￭ An improperly tightened fuel filler cap can loosen or come

off and spill quantities of fuel. To reduce the risk of fuel

spillage and fire from an improperly installed fuel cap,

correctly position and tighten the cap in the fuel tank

opening:

– Raise the grip on the top of the cap until it is upright

at a 90° angle. Insert the cap in the fuel tank opening

with the exterior positioning mark (1) lined up with

the "unlocked" symbol (2) on the fuel tank housing.

– Using the grip, press the cap down firmly while

turning it clockwise to the closed position

(approximately 1/4 turn). In the closed position, the

interior (4) and exterior (1) positioning marks will

align with the "locked" symbol (3) on the fuel tank

housing.

– Fold the grip flush with the top of the cap and check

for tightness.

– If the grip does not lie completely flush with the cap

or the detent on the grip does not fit in the

corresponding recess in the tank opening, or if the

cap is loose, the cap is not properly seated and you

must repeat the above steps. Refer to the procedure

below for returning the base of the cap to the proper

starting position for installation.

Misaligned, Damaged or Broken Cap

WARNING

￭

￭ If the cap does not drop fully into the fuel tank opening

when the positioning marks (1, 2) line up, or if it does not

tighten properly when turned, the base of the cap may be

prematurely rotated in relation to the top. Such

misalignment can result from handling, cleaning or an

improper attempt at tightening.

– Illustrations A and B: The base of the cap is prematurely

rotated to the closed position and is not in the correct

starting position for installation. The tank will not seal in

this configuration. Note: in Illustrations A and B, the

interior positioning marks (1) are in line with the exterior

positioning marks (2).

– Illustration C: The bottom of the cap is in the correct

starting position for installation. Note: in Illustration C,

the interior positioning mark (1) is under the grip and not

in line with the outer positioning mark (2).

￭

￭ To return the base of the cap to the proper starting

position for installation:

– Drop the cap into the fuel tank opening (A).

– Turn the cap counter-clockwise with slight pressure

until it drops fully into the fuel tank opening

(approx. 1/4 turn) (B). This will rotate the base of the

cap into the correct starting position for

installation (C). The exterior positioning mark (1) on

the cap will line up with the "unlocked" symbol on the

fuel tank housing. The interior positioning mark (3)

should be under the grip and not in line with the outer

positioning mark (1).

– Then, turn the cap clockwise, closing it normally.

0000-GXX-2134-A1

A B C

0000-GXX-3136-A1

ABC

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

￭ If your fuel cap still does not tighten properly, it may be

damaged or broken. Stop using the unit and take it to your

authorized STIHL dealer for repair.

Vapor Lock

WARNING

￭ Vapor lock occurs when fuel in the fuel line or carburetor

vaporizes, causing bubbles to block the free flow of liquid

fuel into the carburetor.

￭ Vapor lock cannot be relieved or affected by opening the

fuel tank. Removing the fuel filler cap without first allowing

the chain saw to cool adequately can result in fuel

spraying. Always follow the instructions in this section

when removing the fuel cap.

￭ To relieve vapor lock:

– Place the Master Control Lever in the start

position and try to start the chain saw, @ 14.

– If your chain saw will not restart, or if vapor lock

occurs again, the chain saw is being used in

conditions too extreme for the fuel being used.

Discontinue use and let the engine cool completely

before attempting to start the chain saw.

– Using good quality, fresh fuel (stored less than 30

days) also can help reduce the occurrence of vapor

lock.

5.6 Using the Chain Saw

5.6.1 Before Operation

WARNING

￭ Misuse or unauthorized use may result in personal injury

and property damage.

– Use the chain saw only as described in this

instruction manual.

￭ For proper assembly of the bar and chain:

– Read and follow the instructions on mounting the

guide bar and chain, @ 10.2.1.

￭ The chain, guide bar and sprocket must match each other

in gauge and pitch. Before mounting or replacing:

– Read the information on guide bar and chain

combinations, @ 26.

– Read and follow the instructions on kickback and

other reactive forces, @ 6.

– Select the shortest bar that will meet your cutting

needs. Longer bars add weight and may be more

difficult to control.

￭ Proper tension of the chain is extremely important to

maximize cutting performance and reduce the risk of

personal injury from chain breakage, derailment or

reactive forces:

– Read and follow the chain tensioning instructions,

@ 10.3.

– Always make sure the chain sprocket cover is

tightened securely after tensioning the chain in order

to secure the bar. Never start the chain saw with the

chain sprocket cover loose or missing.

– Check chain tension once more after tightening the

chain sprocket cover.

– After adjusting the chain, let the motor run for a

minute or two, then shut off the engine, engage the

chain brake and recheck chain tension.

– Check chain tension periodically thereafter at

regular intervals (only after engaging the chain brake

and shutting off the engine).

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

– Never cut with a loose chain. If the chain becomes

loose while cutting, engage the chain brake and shut

off the engine before tightening the chain. Never

attempt to adjust the chain while the engine is

running.

￭ To reduce the risk of fire and explosion:

– Check fuel system for leaks, especially the visible

parts, (e.g., filler cap, hose connections).

– Securely mount the spark plug boot on the spark

plug.

– Do not start the engine if the fuel system has leaks

or the saw is otherwise damaged. Have the chain

saw repaired by an authorized STIHL servicing

dealer before using it.

￭ Using a chain saw that is modified, damaged, improperly

adjusted or maintained, or not completely and securely

assembled can lead to a malfunction and increase the risk

of serious personal injury or death.

– Never operate a chain saw that is modified,

damaged, improperly maintained or not completely

and securely assembled.

– Always check your chain saw for proper condition

and operation before starting work, particularly the

throttle trigger, throttle trigger lockout, Master

Control Lever, front hand guard, chain brake and

cutting attachment.

– Ensure that the throttle trigger and throttle trigger

lockout move freely and always spring back to the

idle position when released. The throttle trigger must

not engage until the throttle trigger lockout is

depressed. The Master Control Lever must move

easily to STOP.

– Never attempt to modify or override the controls or

safety devices in any way.

– If your saw or any part is damaged or does not

function properly, take it to your authorized STIHL

servicing dealer. Do not use the saw until the

problem has been corrected.

￭ Before starting the engine and disengaging the chain

brake, take the following steps to reduce the risk of

personal injury from reactive forces, loss of control or

inadvertent contact with the chain:

– Be sure that the guide bar and chain are clear of you

and all other obstructions and objects, including the

ground.

– Never attempt to start or accelerate the engine when

the guide bar is in a cut or kerf. Doing so could lead

to reactive forces and injury.

– Read and follow the instructions on starting the

chain saw, @ 14.

5.6.2 Starting

WARNING

￭ To reduce the risk of burns and other personal injury from

escaping gas vapor and fumes:

– Move at least 10 ft. (3 m) from the fueling spot before

starting the engine.

– Start your chain saw only outdoors.

￭ To reduce the risk of injury from chain contact and/or

reactive forces:

– Engage the chain brake before starting the chain

saw.

￭ To reduce the risk of serious or fatal injuries to the

operator or bystanders from loss of control:

– Start the chain saw only as described in the

"Starting" chapter in this manual, @ 14.

– Do not drop start. Drop starting means pushing the

chain saw away from the operator, or allowing it to

drop toward the ground, while pulling on the starter

grip. This method is very dangerous because you

may lose control of the chain saw.

– When you pull the starter grip, do not wrap the

starter rope around your hand.

– Do not let the grip snap back. Guide the starter rope

to rewind it properly.

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

– Be sure that the guide bar and chain are clear of you

and all other obstructions and objects, including the

ground. Never attempt to start the chain saw when

the guide bar is in a cut or kerf.

– Always engage the chain brake before starting.

When the engine is started, the engine speed with

the starting throttle lock engaged will be fast enough

for the clutch to engage the sprocket and, if the chain

brake is not activated, turn the chain.

– Once the engine has started, immediately blip the

throttle trigger, which should release the Master

Control Lever to the run position and allow the

engine to slow down to idle.

￭ Accelerating the engine while the chain brake is engaged

or the chain is otherwise blocked (i.e., not able to turn)

increases the load and will cause the clutch to slip

continuously. This may occur if the throttle is depressed

for more than a few seconds when the chain is pinched in

the cut or the chain brake is engaged. To reduce the risk

of overheating and damage to important components

(e.g., clutch, polymer housing components):

– Always disengage chain brake before accelerating

engine and before starting cutting work. The only

exception to this rule is when you check operation of

the chain brake.

5.6.3 Holding and Controlling the Chain Saw

WARNING

￭ To maintain a firm grip and properly control your chain

saw:

– Keep the handles clean and dry at all times. Keep

them free of moisture, pitch, oil, grease and resin.

￭ To reduce the risk of serious or fatal injuries to the

operator or bystanders from loss of control:

– Place your left hand on the front handle and your

right hand on the rear handle (see illustration). Left-

handers must follow these instructions too.

– Wrap your fingers tightly around the handles,

keeping the handles cradled between your thumb

and forefinger.

– Position the chain saw in such a way that all parts of

your body are clear of the cutting attachment

whenever the engine is running. Stand to the left of

the cut while bucking, outside of the cutting plane

(see illustration).

– Read and follow all warnings and instructions in the

chapter Kickback and Reactive Forces, @ 6.

￭ Operating the chain saw with one hand is extremely

dangerous. One-handed operation makes it difficult to

oppose and absorb reactive forces (pushback, pull-in,

kickback) without losing control of the chain saw. It also

makes it difficult to prevent the bar and chain from skating

or bouncing along a limb or log. To reduce the risk of

serious or fatal injury to the operator or bystanders from

loss of control:

0000-GXX-4119-A0

– Avoid contacting any object with the

upper quadrant of the tip of the guide

bar. It may cause kickback to occur.

– Always hold the chain saw firmly with

both hands when you are working.

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

￭ To reduce the risk of serious or fatal cut injuries to the

operator or bystanders from loss of control, keep proper

footing and balance at all times:

– Take special care in overgrown or wet terrain and

always watch for hidden obstacles such as tree

stumps, roots, rocks, holes and ditches to avoid

stumbling or falling.

– Be extremely cautious when working on slopes or

uneven ground.

– For better footing, always clear away fallen

branches, scrub and cuttings. Freshly debarked logs

and other material can increase the danger of

slipping, tripping or falling.

– Use extreme caution when cutting small-size brush,

branches and saplings because slender material

may catch the chain and spring toward you or pull

you off balance.

￭ To reduce the risk of injury from loss of control:

– Do not overreach. Keep proper footing and balance

at all times.

– Never attempt to start or accelerate the engine when

the guide bar is in a cut or kerf. Doing so could lead

to reactive forces and injury. Instead, remove the

guide bar from the cut and re-enter the cut at full

throttle, taking care to avoid contacting any object

with the tip of the guide bar.

￭ The bumper spike is designed to provide greater control

of the chain saw while cutting. If you work without the

bumper spike, the chain saw may pull you forward

suddenly. This could cause loss of control or, if the tip of

the guide bar strikes an object, kickback.

– Position the bumper spike against the material you

are cutting and use it as a fulcrum.

– Always work with the bumper spike to maintain

better control of the saw.

￭ Applying pressure to the chain saw when reaching the end

of a cut may cause the bar and rotating chain to accelerate

out of the kerf, go out of control and strike the operator or

some other object. To reduce the risk of injury:

– Use caution when approaching the end of a cut.

– Never put pressure on the chain saw when reaching

the end of a cut.

– STIHL recommends that first-time chain saw users

work under the supervision of an experienced

operator.

5.6.4 Working Conditions

WARNING

￭ Operate your chain saw only under good visibility during

favorable daylight conditions.

– Postpone the work if the weather is windy, foggy,

rainy or inclement.

– Never cut near power lines.

￭ Your chain saw is a one-person machine.

– Do not allow other persons in the general work area.

– Bystanders, especially children, and animals should

not be allowed in the area where it is in use.

– Shut off the engine immediately if you are

approached. Engage the chain brake.

– Never attempt to operate the chain saw

with one hand.

– Never work on a ladder, roof, in a tree or

while standing on any other insecure

support.

– Never operate the chain saw above

shoulder height.

0000-GXX-1889-A0

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

￭ To reduce the risk of injury to bystanders and

unauthorized users:

– Never leave the chain saw unattended when the

engine is running.

– Shut off the engine and engage the chain brake

during work breaks and any other time the chain saw

is not in use.

￭ To reduce the risk of fire and explosion:

– Never operate the chain saw in a location where

combustible gases, liquids, vapors, dusts or other

combustible materials and substances are present.

– Always move the Master Control Lever to stop

position 0 before pulling the starter grip if the spark

plug boot has been removed.

– Read and follow recommendations issued by

government authorities for identifying and avoiding

the hazards of combustible gases, liquids, vapors,

dusts or other combustible materials and

substances.

– Never modify the chain saw muffler or spark

arresting screen.

￭ If a rotating chain strikes a rock or other hard object,

sparks may be created, which can ignite flammable

materials under certain circumstances. Flammable

materials can include dry vegetation and brush,

particularly when weather conditions are hot and dry.

– When there is a risk of fire or wildfire, do not use your

chain saw around flammable materials or around dry

vegetation or brush.

– Contact your local fire authorities or the Canadian

Forest Service if you have any question about

whether vegetation and weather conditions are

suitable for the use of a chain saw.

￭ As soon as the engine is running, it generates toxic

exhaust gases containing chemicals, such as unburned

hydrocarbons (including benzene) and carbon monoxide,

that are known to cause respiratory problems, cancer,

birth defects, or other reproductive harm. Some of the

gases (e. g. carbon monoxide) may be colorless and

odorless. To reduce the risk of serious or fatal injury or

illness from inhaling toxic exhaust gases:

￭ Using this chain saw and sharpening its chain can

generate dust, oil mist and other substances containing

chemicals known to cause respiratory problems, cancer,

birth defects and other reproductive harm.

– Consult governmental agencies such as ECCC,

CCOHS and PHAC and other authoritative sources

on hazardous materials if you are unfamiliar with the

risks associated with the particular substances you

are cutting or with which you are working.

￭ Inhalation of certain dusts, especially organic dusts such

as mold or pollen, can cause susceptible persons to have

an allergic or asthmatic reaction. Substantial or repeated

inhalation of dust or other airborne contaminants,

especially those with a smaller particle size, may cause

respiratory or other illnesses. This includes wood dust,

especially from hardwoods, but also from some softwoods

such as Western Red Cedar.

– Control dust (such as saw dust) and mists (such as

oil mist from chain lubrication) at the source where

possible.

– Always work with a properly sharpened chain, which

produces wood chips rather than fine dust.

– To the extent possible, operate the chain saw so that

the wind or operating process directs any dust, mist

or other particulate matter raised by the chain saw

away from the operator.

– When respirable dust or other particulate matter

cannot be kept at or near background levels, always

wear a respirator that is approved by PHAC and

rated for worksite-specific conditions. Follow the

– Never operate the chain saw indoors, in

confined spaces or other poorly

ventilated locations.

– If exhaust fumes become concentrated

due to insufficient ventilation, clear

obstructions from the work area. Ensure

proper ventilation before proceeding.

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

recommendations of governmental authorities (e.g.,

CCOHS/PHAC) and occupational and trade

associations.

￭ If the vegetation being cut or the surrounding ground is

coated with a chemical substance, such as pesticide or

herbicide:

– Read and follow the instructions and warnings that

accompanied the substance coating the vegetation

or surrounding ground.

￭ Breathing asbestos dust is dangerous and can cause

severe or fatal injury, respiratory illness or cancer,

including mesothelioma. The use and disposal of

asbestos-containing products is strictly regulated by

CCOHS and the ECCC.

– Do not use your chain saw to cut or disturb asbestos

or asbestos-containing products.

– Stop work immediately and contact the relevant

state and local authorities and/or ECCC, your

employer or local CCOHS representative if you have

reason to believe that you might be disturbing

asbestos.

￭ Repeated contact with waste oil can cause skin cancer

and its use is harmful to the environment.

– Do not use waste oil to lubricate the bar and chain of

your STIHL chain saw.

5.6.5 Operating Instructions

WARNING

￭ In the event of an emergency:

– Shut off the engine immediately and engage the

chain brake.

￭ To reduce the risk of personal injury from loss of control

and/or contact with the chain:

– Do not use your chain saw with incorrect idle

adjustment. When the idle speed is correctly

adjusted, the chain should not move when the saw

running at idle. If it does, have your STIHL dealer

check your chain saw and make proper adjustments

and repairs before use.

￭ To reduce the risk of severe personal injuries from

unintentional starting:

– Never touch a chain with your hand or any part of

your body when the engine is running, even when

the chain is not rotating.

￭ The chain continues to move for a short period after the

throttle trigger is fully released. This is known as the

"flywheel effect." To reduce the risk of serious personal

injury from contact with the chain:

– Wait for the chain to stop and engage the chain

brake before walking with the chain saw or putting it

down.

￭ Your chain saw is equipped with a chain catcher. It is

designed to reduce the risk of personal injury in the event

of a thrown or broken chain.

– Never operate the chain saw with a damaged or

missing chain catcher.

￭ Contacting foreign objects while sawing might cause the

chain to break or be thrown, or cause the chain saw to

propel dangerous debris or kick back in the direction of the

operator. To reduce the risk of severe or fatal personal

injury caused by contact with foreign objects:

– Inspect the tree, log or branch before cutting.

– Remove any foreign objects to ensure that the wood

is free of materials such as nails, spikes, cables, or

wires.

– Before starting a cut, ensure that it can be completed

without contacting surrounding objects or structures

such as fencing or stonework.

￭ Check the chain saw, chain and guide bar at regular short

intervals during operation, or immediately if there is a

change in cutting behavior:

– Shut off the engine and activate the chain brake.

– Have damaged, broken or excessively worn anti-

vibration elements replaced immediately. A

"sponginess" in the feel of the saw, increased

0458-790-8221-A

English

5 IMPORTANT SAFETY INSTRUCTIONS

vibration or increased "bottoming" during normal

operation may indicate damage, breakage or

excessive wear.

– Anti-vibration elements should always be replaced in

sets. If you have any questions as to whether the

anti-vibration elements should be replaced, consult

your authorized STIHL servicing dealer.

– Check the condition and tension of the chain. Look

for damage to the chain or guide bar.

– If the chain cannot be properly tensioned, or if other

components of the saw are worn or damaged, stop

work immediately and take your chain saw to an

authorized STIHL servicing dealer for inspection,

repair or maintenance.

￭ The muffler and other parts of the engine (e.g. fins of the

cylinder, spark plug) become hot during operation and

remain hot for a while after stopping the engine. To reduce

the risk of burn injury:

– Allow the engine to cool before inspecting,

transporting or storing the chain saw. Avoid

contacting the muffler while it is still hot following

operation.

– Keep the area around the muffler clean. Remove

excess lubricant and all debris such as pine needles,

branches or leaves.

– Allow the chain saw to cool on concrete, metal, bare

ground or solid wood (e.g. the trunk of a felled tree)

away from any combustible substances.

– Do not continue work with a damaged or improperly

mounted cylinder housing or a damaged/deformed

muffler shell. It may interfere with the cooling

process of the muffler.

￭ The muffler of this chain saw is furnished with a spark

arresting screen. If your gas/oil mix ratio is correct (i.e.,

not too rich), this screen will normally stay clean as a

result of the heat from the muffler and need no service or

maintenance. To reduce the risk of fire from the emission

of hot particles:

– Never operate your chain saw with a missing or

damaged spark arresting screen.

– If you experience loss of performance and suspect a

clogged screen, have your muffler serviced. Some

state or federal laws or regulations may require a

properly maintained spark arrester for certain uses.

￭ In California, it is a violation of § 4442 or § 4443 of the

Public Resources Code to use or operate gasoline-

powered tools on forest-covered, brush-covered or grass-

covered land unless the engine's exhaust system is

equipped with a complying spark arrester that is

maintained in effective working order. The owner/operator

of this product is responsible for properly maintaining the

spark arrester. Other states or governmental

entities/agencies, such as the Canadian Forest Service,

may have similar requirements.

– Do not use your chain saw around flammable

materials or around vegetation or brush when there

is a risk of fire or wildfire.

– Contact your local fire authorities or the Canadian

Forest Service if you have any question about laws

or regulations relating to fire protection

requirements.

DANGER

￭ To reduce the risk of electrocution:

– Never operate this chain saw in the

vicinity of any wires or cables that may

be carrying electric current.

– Never cut near power lines.

– Do not rely on the chain saw's insulation

against electric shock.

La page charge ...

STIHL MS 462 C-M Manuel utilisateur

Marque: STIHL

Modèle: MS 462 C-M

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: STIHL MS 462 C-M User manual

STIHL MS 462 C-M Manuel utilisateur

STIHL MS 462 C-M Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents