Sony TCM-4TR Mode d'emploi

Catégorie
Lecteurs de cassettes
Taper
Mode d'emploi

Ce manuel convient également à

1998 by Sony Corporation Printed in China
3-862-269-14 (1)
Cassette-Corder
Operating Instructions
Mode d‘emploi
TCM-4TR
EN
F
2
EN
For the customers in the U.S.A.
Owner’s Record
The model number is located at the bottom and the serial number is
located inside the tape holder. Record the serial number in the space
provided below. Refer to whenever you call upon your Sony dealer
regarding this product.
Model No. TCM-4TR Serial No.
INFORMATION
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
3
EN
EN
Table of Contents
Welcome!...................................................................... 4
Getting Started
Preparing a Power Source ......................................... 6
Dry Batteries .......................................................... 6
House Current .................................................... 11
Operating the Unit
Playing a Tape ........................................................... 12
Playing a 4-track Tape ....................................... 12
Playing a 2-track Tape ....................................... 16
Adjusting the Playback Speed (DPC Function) ... 17
Recording ................................................................... 20
Recording Cue Marks .............................................. 26
Recording from Various Sound Sources ............... 28
Recording with an External Microphone ........ 28
Recording from Another Equipment............... 29
Additional Information
Precautions ................................................................ 30
Maintenance .............................................................. 32
Troubleshooting ........................................................ 33
Specifications ............................................................. 36
Location of parts and controls ................................ 38
Index ........................................................................... 40
LIMITED WARRANTY ........................................... 41
4
EN
Welcome!
Thank you for purchasing the Sony Cassette-
Corder.
This Cassette-Corder is a product which Sony
Corporation developed specially for visually
impaired people. You can play back a tape
recorded on 4 tracks at 2.4 cm/s.
Some features are:
You can play back a 4-track tape as well as a
normal 2-track tape.
You can play back and record with two tape
speeds (4.8cm/s and 2.4cm/s).
DPC (Digital Pitch control) allows you to increase
or decrease the speed of the playback sound
(page 17). If you change the playback tape speed,
the pitch will be automatically adjusted.
The CUE MARKER function locates a specific
point on a recording (page 26).
Built-in flat microphone for clear recording of
speaker’s voice.
5
EN
When the batteries are running out of power, a
beep sounds (page 9).
The BATT/REC lamps indicate the remaining
battery power in two steps. A beep sounds and
the i lamp shows when to replace the batteries
(page 9).
Automatic shut-off mechanism at the end of the
tape (in the recording/playback mode only).
Stop-pause-release function —The pause switch
is released automatically when the p STOP
button is depressed, so that you won’t miss a
recording chance (pages 15, 22).
Notes
Recording can be made with 2 speeds but only
on 2 tracks. Note that 4-track recording cannot
be made.
•A tape recorded in stereo cannot be played
back properly.
•A tape recorded with 2.4cm/s tape speed
using this unit cannot be played back on a
normal tape recorder.
6
EN
}
}
]
]
z Getting Started
Preparing a Power Source
Choose either one of the following power sources:
dry batteries (see below) or house current (see
page 11).
Dry Batteries
Make sure that nothing is connected to the DC IN
3 V jack.
1 Open the battery compartment lid.
2 Insert two R6 (size AA) batteries (not
supplied) with correct polarity and close the
lid.
DC IN 3V jack
7
EN
}
]
}
]
Notes
Do not charge a dry battery.
Do not use a new battery with an old one.
Do not use different types of batteries.
When you do not use the unit for a long time, remove
the batteries to avoid any damage caused by battery
leakage and subsequent corrosion.
Dry batteries will not be expended when another
power source is connected.
To take out the batteries
To attach the battery compartment lid
if it is accidentally detached
Attach it as illustrated.
Continued
8
EN
Preparing a Power Source (continued)
Battery life (Approximate hours) (EIAJ*)
Sony alkaline Sony
LR6(SG) R6P(SR)
Recording (4.8cm/s) 6.5 1.0
Recording (2.4cm/s) 7.0 1.5
Playback (4.8cm/s) 6.5 1.0
Playback (2.4cm/s) 7.0 1.5
* Measured value by the standard of EIAJ (Electronic
Industries Association of Japan)(Using a Sony HF-
series cassette tape)
We recommend to use long-life alkaline batteries.
Note
The battery life may shorten depending on the
operation of the unit.
9
EN
When to replace the batteries
When the batteries are running out of power, a
beep sounds and the BATT/REC lamps go off and
the i lamp flashes. When this happens, replace
the batteries with new ones.
The BATT/REC lamps change as illustrated.
When batteries
are new
When batteries
become weak
light
flash
Replace batteries
light
Continued
(A beep sounds.)
10
EN
Preparing a Power Source (continued)
Notes
During recording, you will hear the beep through the
earphone. During playback, you will hear the beep
through the earphone and the speaker.
During FF (CUE) or REW (REVIEW), the i lamp may
flash with a beep. Only when the tape does not run
properly, replace the batteries.
In some cases when the unit is used with rechargeable
batteries, only one BATT/REC lamp will light even
though the batteries have been fully charged.
After the batteries have been used for a while, the
BATT/REC lamp(s) may flash with the playback
sound when you turn up the volume; however, this
does not mean that you need to replace the batteries.
The unit will play back normally for a while even after
i lamp flashes with a beep. However, replace the
batteries as soon as you can. If you do not, a loud
noise may be emitted by the built-in speaker or
subsequent recording will not be done correctly.
When the tape starts running or at the end of the tape
the i lamp may momentarily light with a short beep.
If the lamp goes off, you do not need to replace the
batteries.
11
EN
House Current
Connect the AC power adaptor to DC IN 3V and
to the wall outlet. Use a commercially-available
AC power adaptor (rated output voltage/current:
3 V DC/700 mA). Do not use any other AC power
adaptor.
DC IN 3V
to the wall outlet
Polarity of the plug
Notes
The voltage of power supply is different depending on
the country. Please buy an AC power adaptor in the
country where the product is to be used.
Depending on the AC power adaptor, noise may be
heard while using the unit. Refer to the operating
instructions of the AC power adaptor.
AC power adaptor (not supplied)
12
EN
z Operating the Unit
Playing a Tape
Playing a 4-track Tape
1 Open the cassette compartment lid.
2 Insert a cassette with the side to start
playing facing the lid.
3 Close the cassette compartment lid.
4 Set TAPE SPEED to 2.4 (cm/s) .
( PLAY
TAPE TRACK
TAPE SPEED
13
EN
5 Set TAPE TRACK to 1-2 or 3-4 and start
playback.
To play the tape from the beginning, follow the
procedure below. Make sure that side A is
facing the lid.
1 Set TAPE TRACK to 1-2 and press ( PLAY.
Track 1 will be played. At the end of the
tape, playback stops automatically.
2 Take out the cassette and reinsert the cassette
with side B facing the lid.
3 Leaving TAPE TRACK at 1-2, press
( PLAY. Track 2 will be played.
4 Take out the cassette and reinsert the cassette
with side A facing the lid.
5 Set TAPE TRACK to 3-4 and press ( PLAY.
Track 3 will be played.
6 Take out the cassette and reinsert the cassette
with side B facing the lid.
7 Leaving TAPE TRACK at 3-4, press
( PLAY. Track 4 will be played.
When the tape comes to an end
Playback stops and the unit turns off automatically
(Automatic shut-off mechanism).
After fast forward or rewind, press p STOP, as the unit
does not automatically enter the stop mode at the end of
the tape.
Continued
14
EN
VOL
p STOP
) FF/CUE
0 REW/
REVIEW
( PLAY
TAPE TRACK
Playing a Tape (continued)
TAPE SPEED
PAUSE c
EAR jack
To
Adjust the volume
Stop playback/stop
fast forward or
rewind
Pause playback
Fast forward**
Rewind**
Do this
Turn VOL.
Press p STOP.
Slide PAUSE c.
To release pause playback, release
PAUSE c*.
Press ) FF/CUE during stop.
Press 0 REW/REVIEW during
stop.
15
EN
Do this
Press and hold ) FF/CUE and
release it at the point you want.
Press and hold 0 REW/REVIEW
and release it at the point you
want.
Press p STOP and open the
cassette compartment lid by hand.
* PAUSE c will be also automatically released when
p STOP is pressed (stop-pause-release function).
**If you leave the unit after the tape has been wound or
rewound, noise will be heard. Be sure to depress
p STOP. Otherwise, the batteries will be consumed
rapidly.
To
Search forward
during playback
(CUE)
Search backward
during playback
(REVIEW)
Take out a cassette
To listen through the earphones
Connect the supplied earphones to the EAR jack.
Continued
16
EN
Playing a Tape (continued)
Playing a 2-track Tape
1 Proceed with steps 1 to 3 on page 12.
2 Set TAPE SPEED to 2.4 (cm/s) or 4.8 (cm/s) to
match the tape speed used for recording.
3 Set TAPE TRACK to 1-2.
4 Press ( PLAY.
Other operations are the same as those of playing a
4-track tape described on pages 14 and 15.
Note
If the recording is made in stereo, only the L channel is
heard.
17
EN
Adjusting the Playback
Speed (DPC Function)
The DPC (Digital Pitch Control) function allows
you to increase or decrease the playback speed.
When playing back a tape with 2.4cm/s tape speed
such as a 4-track tape, the playback speed will be
adjusted from approximately +100% to 0%.
When playing back a tape with 4.8cm/s tape
speed, the playback speed will be adjusted from
approximately +100% to –50%.
If you change the playback tape speed, the pitch
will be automatically adjusted.
Continued
18
EN
Adjust DPC as follows:
To play back Set DPC to
faster (2.4 cm/s tape) FAST
(4.8 cm/s tape) FAST
at normal speed Center
slower (2.4 cm/s tape ) Not available
(4.8 cm/s tape) SLOW
DPC
Adjusting the Playback Speed (DPC Function)
(continued)
19
EN
Notes
When playing back a tape with 2.4cm/s tape speed,
the playback speed will be normal even if you set DPC
to SLOW.
Even though you use DPC, you cannot acquire the
same pitch as the original. The tone will be somewhat
different from the original.
When the power of the batteries is weak, the DPC may
make noise if you turn it fast. In that case turn it
slowly or change the batteries.
When DPC is turned or the volume is adjusted during
playback, BATT/REC lamps may flicker.
20
EN
Recording
You can record the sound easily with the built-in
microphone. Use a normal (TYPE I) tape.
Make sure that nothing is connected to the MIC
jack.
1 Open the cassette compartment lid.
2 Take out any slack in the tape and insert the
cassette with the side to start recording
facing the lid.
3 Close the cassette compartment lid.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Sony TCM-4TR Mode d'emploi

Catégorie
Lecteurs de cassettes
Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues