Uniden GMR3050-2C Le manuel du propriétaire

Catégorie
Radios bidirectionnelles
Taper
Le manuel du propriétaire
F R S
2-way
radios
GMR3050-2C
Congratulations on your purchase of a Uniden FRS radio.
This lightweight, palm-sized radio is a state-of-the-art
device, equipped with many valuable features. Use it at
sporting events, to stay in contact with family and friends,
hiking, skiing, outdoors, or in a neighborhood watch for vital
communication.
22 FRS Channels Battery Charger
121 Privacy Codes Silent Mode
Up to 30-Mile Range* microUSB charging jack
Channel Scan 10 Selectable Call Tone
Alerts
VOX Headset Jack Auto Squelch
Roger Beep
* Range may vary depending on environmental and/or
topographical conditions.
GMR3050-2C HARDWARE
1
2
3
4
5
6
7
8
10
11
9
1 Antenna 7 Speaker
2 USB Charge Port/
Headphone Jack
8 Channel and Volume
3 Push to Talk 9 Backlight
4 Microphone 10 CH/LOCK
5 MENU/Power 11 Screen
6 CALL/MON
WHAT'S IN THE BOX
Your package contains 2 radios, 6 AA
rechargeable NiMH batteries, one AC adapter/
Y-Split microUSB charge cable, 2 belt clips, and
this reference guide.
Visit our web site at www.uniden.com to order
accessories.
Use only Uniden accessories.
Each radio uses 3 AA rechargeable NiMH
batteries (included).
To install the batteries:
1. If installed, remove the belt clip.
2. Remove the battery compartment door by
pressing on the latch and releasing the
cover. Remove it.
3. Install the supplied 3 AA NiMH batteries
into the battery compartment. Be certain
to follow the + and – symbols in the
compartment. Installing the batteries
incorrectly will prevent the unit from
operating.
4. Replace the battery compartment door.
5. Replace the belt clip if necessary.
6. Repeat for each radio.
Note: You may also use 3 AA non-rechargeable
alkaline batteries in each radio.
However, do not mix NiMH and alkaline
batteries in the same radio.
CHARGING THE RADIO
Review the following tips before charging your
radios:
CAUTION: Do not attempt to recharge
alkaline batteries. Doing so can
create a safety hazard or damage the
radio.
Install the batteries before connecting the AC
adapter to the radio and power source.
The battery icon flashes while the radio
charges, whether the radio is turned on or
not. The charge stops after 14 hours of
continuous charging. If there is a power
interruption, the charging timer resets to 14
hours. If the radio is off and charging stops,
the battery icon stops flashing.
Charge time may vary depending on the
battery life remaining. For fastest charging,
turn off the radio before charging.
If battery power is low, you cannot operate
the radio even using external power. If you
try to transmit while power is low, the radio
will automatically turn off. Recharge the
batteries.
GMR3050-2C charges through a microUSB
Y-branch cable (provided) with an AC adapter
end that plugs into an AC power source.
1. Plug one branch of the microUSB Y-Cable
into each radio's microUSB charge port.
2. Insert the AC adapter end into an AC
power source (wall plug).
INSTALL THE BATTERIES
3. The radio is fully charged when the battery
charging icon stops flashing.
USING THE RADIO
Turning the Radio On and Adjusting the
Volume
1. Press and hold the MENU/ key to turn
the radio ON.
2. To change the volume level, press the
or key to increase or decrease the
volume level. There are 8 volume levels (L1
- L8) plus volume off (L0)
3. Press and hold the MENU/ key to turn
the radio OFF.
Using Headphones
Your radio has a headphone jack to support
earphones/earbuds (not included). Using the
earbuds lets you have more private
communications. To use headphones/earbuds,
lift the rubber cover from the headset jack, then
plug in the headphones/earbuds.
Important: Your radio is not weather resistant
when using the headset jack. When you remove
the headphones/earbuds, be sure to fully press
the cover into place to restore the radio's
weather resistant capability.
Using the Menu
Press MENU/ to access the three menu
options:
Privacy Code (121 codes). The privacy codes
display underneath the channel number on
the screen.
Call Tone (10 call tone options plus Off)
VOX (5 levels plus Off)
Each menu option is discussed later in the
manual with the feature that uses it.
Choosing a Channel
Your radio has 22 channels you can use to talk
to others. In order to speak to someone, each of
you must be set to the same channel and privacy
code.
Each of the channels 1-22 may have any one of
the privacy codes, 0 (OFF), or 1-121 selected.
Code oF (OFF) indicates no privacy code
selected and your radio can receive a signal
regardless of the code settings of the transmitting
radio.
To choose a privacy code:
1. Press MENU/ until the privacy code
number flashes below the channel number.
2. Press or to cycle through the privacy
codes.
3. The radio returns to its normal state after
about 5 seconds.
To choose a channel:
1. Press the CH/LOCK key to access the
channel function; the channel number
flashes.
2. Press ▲ or ▼ to manually cycle through
the channels.
You can only manually cycle through channels
when the channel numbers are flashing.
3. Press CH/LOCK to set the channel.
VOX Feature
CAUTION: Insert headphones into the radio
BEFORE turning on the radio.
Your radio is equipped with a user selectable
Voice Operated Transmitter (VOX) that can be
used for automatic voice transmissions. The
VOX feature is designed to be used with or
without a headset with a microphone.
Transmission is initiated by speaking into the
microphone instead of pressing PTT.
To select a VOX level:
1. Press MENU/ repeatedly until the vox
icon and the VOX sensitivity level (OFF,
1-5) blink.
2. Press or to change the VOX
sensitivity levels. Use level 5 for increased
sensitivity to voice in normally quiet
environments, and use a higher level to
reduce undesired activation in very noisy
environments.
Channel Scan Feature
Your radio has a channel scan feature that allows
you to easily scan all 22 channels. When an
active channel is detected, the unit pauses on
that channel until the channel is clear. Then, after
a 2 second delay, the radio continues scanning.
Press CH/LOCK to resume scanning while the
radio is stopped on an active channel.
When it stops on an active channel, press the
PTT button to transmit on that channel.
Using channel scan
Press CH/LOCK then hold or ▲ for 3
seconds. The radio will repeatedly cycle
through all 22 channels. To reverse scan
direction, press the other directional icon.
Press MENU/ or CALL/MON to stop
scanning.
Silent Mode
Silent mode turns off all key beeps when it is
turned on. It does NOT mute call or voice signals
received.
Change Silent mode status (OFF or ON) by first
turning OFF the radio.
Turn Silent mode off by pressing the MENU/
key to turn the radio ON. Silent mode is
off and key beeps sound. (Default)
Turn Silent mode on by pressing the CALL/
MON and MENU/ keys to turn the radio
back ON. Silent mode turns on and no key
beeps sound.
Talking on Your Radio
When the radio stops on a channel that is
transmitting, you can talk to others on that
channel:
Transmitting
1. Press and hold the PTT button and speak in a
clear, normal voice about 2-3 inches away from
the microphone on the earbud cord. (The tx icon
displays while you are transmitting. Pause slightly
after pressing the PTT button before you start
talking to prevent cutting off your transmission.)
2. When you are finished speaking, release the PTT
button. You can now receive incoming calls. While
receiving, the rx icon displays.
Transmitting a Call Alert Tone
Your radio is equipped with a call tone that will be
transmitted when the CALL/MON key is pressed. You
can select from 10 call tones.
1. Press MENU/ until call displays on the screen
and the call tone number displays.
2. Press or to cycle through the call tones. A
sample of the tone sounds as you move through
them
3. The radio returns to its normal state after about 5
seconds.
To transmit the call tone, press the CALL/MON key.
Auto Squelch Feature
The radio is equipped with an automatic squelch
system which shuts off weak transmissions and
unwanted noise due to terrain conditions or range
limitations.
Monitor Mode Feature
Your radio allows you to listen for weak signals on the
current channel at the press of a key.
To turn ON Monitor Mode:
Press and hold CALL/MON for 2 seconds. On a
channel that does not have activity, you will hear only
an open-squelch hissing noise and rx displays.
To turn OFF Monitor Mode:
Press the CALL/MON key for 2 seconds again. rx
does not display.
Backlight
Press and hold to turn on the LCD backlight. The
screen stays illuminated for 10 seconds before the
backlight turns off.
Key Lock
1. Press and hold CH/LOCK; displays. The
following functions are not affected by Key Lock:
Volume adjust
Enter monitor mode
PTT transmission
Backlight
Power off
2. Press and hold CH/LOCK again; disappears.
Channels 22 FRS
Privacy Codes 38 Sub-Codes
83 DCS Codes
SPECIFICATIONS
Operating
Frequency
UHF 462.5500 - 467.7125 MHz
Power Source 3 AA NiMH Batteries per radio
FREQUENCY CHART
CH Freq.[MHz] -
Cross Ref.
CH Freq.[MHz] -
Cross Ref.
1 462.5625 - FRS &
GMRS 1
12 467.6625 - FRS 12
2 462.5875 - FRS &
GMRS 2
13 467.6875 - FRS 13
3 462.6125 - FRS &
GMRS 3
14 467.7125 - FRS 14
4 462.6375 - FRS &
GMRS 4
15 462.5500 - GMRS
11
5 462.6625 - FRS &
GMRS 5
16 462.5750 - GMRS
8
6 462.6875- FRS &
GMRS 6
17 462.6000 - GMRS
12
7 462.7125 - FRS &
GMRS 7
18 462.6250 - GMRS
9
8 467.5625 - FRS 8 19 462.6500 - GMRS
13
9 467.5875 - FRS 9 20 462.6750 - GMRS
10
10 467.6125 - FRS 10 21 462.7000 - GMRS
14
11 467.6375 - FRS 11 22 462.7250 - GMRS
15
Note:This product is considered FRS only with 22 FRS
channels in the US market.It is considered a
GMRS product in the Canadian market.
RBRC INFORMATION
As part of our commitment to protect the
environment and conserve natural
resources, Uniden voluntarily participates
in an RBRC
®
industry program to collect
and recycle used Ni-MH batteries within
the US.
Please call 1-800-8-BATTERY for information on Ni-MH
battery recycling in your area. (RBRC
®
is a registered
trademark of the Rechargeable Battery Recycling
Corporation.)
MAINTENANCE
To be safe and sure:
Never open your radio’s case.
Never change or replace anything in your radio
except the batteries.
Care and Safety
Body-Worn Operation
This device was evaluated for body-worn operations
with the supplied belt-clip accessory. (All necessary
accessories are included in the package; any
additional or optional accessories are not required for
compliance with the guidelines.) Third party
accessories (unless approved by the manufacturer)
should be avoided as these might not comply with
FCC RF exposure guidelines.
For body-worn operation, this device has been tested
and meets the Industry Canada RF exposure
guidelines when used with Uniden accessories
supplied or designated for this product. Use of other
accessories may not ensure compliance with Industry
Canada RF exposure guidelines.
Fonctionnement de l’appareil, lorsque porté sur le
corps. Cet appareil a été testé et s’est avéré conforme
aux normes d’Industrie Canada et approuvé pour le
port sur le corps à l’aide des accessoires Uniden
inclus et conçus pour cet appareil. L’utilisation
d'accessoires ne respectant pas les exigences
d'exposition RF d’Industrie Canada doit être évitée.
FCC PART 15/IC COMPLIANCE
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void your
authority to operate the equipment.
Avis de conformité à la FCC : Ce dispositif a été testé
et s’avère conforme à l’article 15 des règlements de la
Commission fédérale des communications (FCC). Ce
dispositif est soumis aux conditions suivantes: 1) Ce
dispositif ne doit pas causer d’interférences nuisibles
et; 2) Il doit pouvoir supporter les parasites qu’il reçoit,
incluant les parasites pouvant nuire à son
fonctionnement.
Tout changement ou modification non approuvé
expressément par la partie responsable pourrait
annuler le droit à l’utilisateur de faire fonctionner cet
équipement.
IC COMPLIANCE
This device contains license-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada's license-exempt
RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. this device must accept any interference,
including interference that may cause undesired
operation of the device.
Changes or modifications not expressly approved by
the party responsible for compliance could void your
authority to operate the equipment.
Cet appareil contient un ou des émetteurs/récepteurs
exemptés de licence qui sont conformes aux normes
RSS d'Innovation, Sciences et Développement économique
Canada exemptées de licence. L'utilisation est soumise aux
deux conditions
suivantes :
1. Cet appareil ne doit pas causer d'interférences.
2. Cet appareil doit accepter toute interférence, y compris
les interférences susceptibles de provoquer un
fonctionnement non désiré de l'appareil.
Tout changement ou modification non approuvé expressément
par la partie responsable pourrait annuler le droit à l’utilisateur
de faire fonctionner cet équipement.
ONE YEAR LIMITED WARRANTY
IMPORTANT! SAVE YOUR RECEIPT! Evidence of original
purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION
("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants, for one year,
to the original retail owner, this Uniden Product to be free from
defects in materials and craftsmanship with only the limitations
or exclusions set out below.
WARRANTY DURATION: This warranty to the original user
shall terminate and be of no further effect 12 months after the
date of original retail sale. The warranty is invalid if the
Product is: (A) damaged or not maintained as reasonable or
necessary, (B) modified, altered, or used as part of any
conversion kits, sub-assemblies, or any configurations not
sold by Uniden, (C) improperly installed, (D) serviced or
repaired by someone other than an authorized Uniden service
center for a defect or malfunction covered by this warranty, (E)
used in any conjunction with equipment or parts or as part of
any system not manufactured by Uniden, or (F) installed or
programmed by anyone other than as detailed by the owner’s
manual for this product.
STATEMENT OF REMEDY: In the event that the product
does not conform to this warranty at any time while this
warranty is in effect, warrantor will either, at its option, repair
or replace the defective unit and return it to you without
charge for parts, service, or any other cost (except shipping
and handling) incurred by warrantor or its representatives in
connection with the performance of this warranty. Warrantor,
at its option, may replace the unit with a new or refurbished
unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE
SOLE AND ENTIRE WARRANTY PERTAINING TO THE
PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL
OTHER WARRANTIES OF ANY NATURE WHATSOEVER,
WHETHER EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OVERPAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow this
exclusion or limitation of incidental or consequential damages
so the above limitation or exclusion may not apply to you.
To clean the radio, use a soft cloth dampened with
water. Do not use cleaners or solvents because they
can harm the body of the unit and leak inside, causing
permanent damage. Use a dry, lint-free cloth to clean
the battery contacts. Do not submerge the unit in
water. If the unit gets wet, turn it off and remove the
batteries immediately.
Dry the battery compartment with a soft cloth to
minimize potential water damage. Leave the battery
compartment cover off overnight to ensure complete
drying. Do not use the radio until the unit is completely
dry.
Your radio might cause TV or radio interference even
when it is operating properly. To determine whether
your radio is causing the interference, turn it off. If the
interference goes away, your radio is causing it. Try to
eliminate the interference by moving your radio away
from the receiver. If you cannot eliminate the
interference, the FCC requires that you stop using the
radio.
Hazardous Environments
Do not operate the radio in hazardous environments.
Explosion or fire may result. Do not operate the radio
near unshielded electrical blasting caps.
Under certain conditions, radios can interfere with
blasting operations and may cause an explosion. Turn
your radio OFF to prevent accidental transmission
when in a blasting area or in areas posted: "Turn off
two-way radio." Construction crews often use remote
control RF devices to set off explosives.
WARNING! Read this information before using the
radio. In August 1996 the Federal Communications
Commission (FCC) of the United States with its action
in Report and Order FCC 96-326 adopted an updated
safety standard for human exposure to radio
frequency electromagnetic energy emitted by FCC
regulated transmitters.
Those guidelines are consistent with the safety
standard previously set by both U.S. and international
standards bodies. The design of the radio complies
with the FCC guidelines and these international
standards.
Never allow children to operate the radio without adult
supervision and the knowledge of the following
guidelines.
FCC RF EXPOSURE
WARNING! It is up to the user to properly operate
this radio transmitter to insure safe operation. Please
adhere to the following:
Do not use the radio with a damaged antenna. If a
damaged antenna comes into contact with the skin, a
minor burn may result. Please contact your local
dealer for a replacement antenna.
Hand-Held Operation (Held-to-Face)
This device was evaluated for typical hand-held (held-
to-face) operations with a 1 inch spacing from the
front of the radio. For hand-held operation, the radio
should be held 1 inch from the user's face in order to
comply with FCC RF exposure requirements.
© 2019 Uniden America Corporation Issue 3, June 2019
All rights reserved Printed in China
LEGAL REMEDIES: This warranty gives you specific legal
rights, and you may also have other rights which vary from state
to state. This warranty is void outside the United States of
America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF
WARRANTY: If, after following the instructions in the owner’s
manual you are certain that the Product is defective, pack the
Product carefully (preferably in its original packaging). The
Product should include all parts and accessories originally
packaged with the Product. Include evidence of original
purchase and a note describing the defect that has caused you
to return it.The Product should be shipped freight prepaid, by
traceable means, to warrantor:
Uniden America Corporation
C/O Saddle Creek
743 Henrietta Creek Road, Suite 100
Roanoke, TX 76262
  • Page 1 1
  • Page 2 2

Uniden GMR3050-2C Le manuel du propriétaire

Catégorie
Radios bidirectionnelles
Taper
Le manuel du propriétaire

dans d''autres langues