DeWalt DCE200 Mode d'emploi

Marque: DeWalt

Modèle: DCE200

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Ce manuel convient également à

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCE200

20V Max* Press Tool

Outil de sertissage 20V Max*

Herramienta de prensado de 20 V Max*

Final print size: 5.5 x 8.5 in.

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 15

Español (traducido de las instrucciones originales) 30

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.

Press jaw

Jaw arms

Jaw retention pin

Lock/release slide

Trigger switch

Reverse trigger switch

Diagnostics panel

Power ON/OFF switch

Micro USB port

Battery pack

Battery release button

Shoulder strap ring

LED Worklight

Shoulder strap clip

Main handle

Tool neck

FIG. A



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

English (original instructions)

GENERAL POWER TOOL SAFETY WARNINGS



WARNING! Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow all

instructions listed below may result in electric shock,

fire and/or seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

h ) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

e ) Do not use a battery pack or tool that is

damaged or modified. Damaged or modified

batteries may exhibit unpredictable behaviour

resulting in fire, explosion or risk of injury.

f ) Do not expose a battery pack or tool to fire

or excessive temperature. Exposure to fire or

temperature above 130 °C may cause explosion.

g ) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and increase

the risk of fire.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

Additional Safety Rules for Press Tool



WARNING: Use the press tool only with

DeWALT

-approved attachments. Other uses or

modifying the press tool for other applications

may damage the press tool, damage the

attachments and/or can result in a faulty

installation. Faulty installations can result in

catastrophic failures, injury to installers and

damage to property.



WARNING: Though this

DeWALT

press tool will

reach the proper pressure to complete a press

successfully, connections can only be effective

when the connection is free from defects and

when the press is properly prepared according

to the fitting manufacturer's installation

procedures. Proper preparation and installation

is the responsibility of the installing contractor.

• Only use

DeWALT

-approved attachments

with a compression range rated for this tool.

• Keep all body parts away from the attachments

during operation and any time the power is ON. A

moment of inattention while operating power tools,

may result in serious personal injury. Fingers or hands

can be crushed, fractured or amputated if they become

caught in the attachments.

• Inspect tool and attachments before use. Never

attempt to repair or use a damaged jaw set or other

attachment. Replace with a new jaw set or attachment.

• This tool produces large forces that can break

attachments or parts and cause injury. Always be

attentive and take proper safety precautions, including

wearing eye protection.

• Crush hazard. Never run the tool without a jaw set or

attachment installed.

• Only trained personnel should operate this tool.

• Before operating, inspect the tool and LEDs on the

diagnostics panel. Correct any problems before using

the tool. Reference the Troubleshooting Guide or

LED Indications sections for a list of possible problems

andsolutions.

• Before operating, inspect job site for hazards

including chemicals or waste that could remain

inpipes.

• Before operating, read and understand all safety

and operating instructions including the fitting

manufacturer's installation instructions and the

instructions for any other equipment used with this

tool. Failure to follow all instructions and warnings

may result in property damage and/or serious

personal injury.

• Keep the pressing area of the tool free from hands

and other objects while tool is in use. Fingers could

be crushed.

• Secure and support the material prior to making the

press to prevent movement during pressing.

• Keep a firm grip on the tool at all times. Forces on the

tool may change during and after the press.

• Press operations may cause material pieces to fly.

Flying particles can cause permanent eye damage.

ALWAYS wear eye protection.

• Always wear gloves when operating tool and

handling materials. The ends of the materials can be

sharp and can cause serious personal injury.

• Always wear safety shoes to protect your feet from

sharp metal debris on the floor.

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... electric shock

hazard

.....................crush hazard

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or serious injury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a short circuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and

Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to

the FLEXVOLT™ battery,

the battery is in Shipping

Mode. Strings of cells are

electrically disconnected within the pack resulting in three

batteries with a lower Watt hour (Wh) rating as compared

to one battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hour batteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 battery implied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or serious injury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center for recycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting battery pack.

Fig. C

2. Insert the battery pack

10

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process has started.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

11

on the battery pack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before first

use.

Charger Operation

Refer to the indicators below for the charge status of the

battery pack.

DCB101

Charging

Fully Charged

Hot/Cold Pack Delay

Problem Pack or Charger

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132:

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

yellow light will turn off and the charger will resume the

charging procedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing to light or by displaying a problem pack or charger

blink pattern.

NOTE: This could also mean a problem with a charger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized service center.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery pack life.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to be cooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of the charger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fully charged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in the slots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaning solutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack in an air temperature below +40°F

(+4.5°C), or above +104°F (+40°C). This is important

and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local service center.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the battery pack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting to clean.

6. Do not freeze or immerse the charger in water or any

other liquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimal results.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged before use.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

INTENDED USE

This press tool is designed for professional pressing of

specific plumbing applications only. Only trained personnel

should operate this tool.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

This press tool is a professional power tool. DO NOT let

children come into contact with the tool. Supervision is

required when inexperienced operators use thistool.

Introduction

The DCE200 Cordless Press Tool uses an electric motor to

power a hydraulic piston pump. The pumping action forces

a ram forward that forces closed a jaw set or attachment.

The attachment mechanically presses fittings onto various

types of tubing to create a tight and permanent seal.

Trigger Switch (Fig. A)

Squeezing the trigger switch

5

advances the hydraulic ram,

while fully releasing the trigger switch stops the advance of

the hydraulic ram.

Reverse Trigger Switch (Fig. A)

Squeezing the reverse trigger switch

6

retracts the

hydraulic ram which releases the pressing action.

Shoulder Strap (Fig. A)



WARNING: The shoulder strap and ring are intended

for transporting the tool. They are not intended for

tethering or securing the tool to a person or object

during use.



WARNING: Do not transport the tool with the

main power ON. Switch the main power OFF prior

totransporting.

Your press tool comes with a shoulder strap. Hook the

shoulder strap clips

14

into the shoulder strap ring

12

LED Worklight (Fig. A)

The LED worklight

13

is located on the foot of the tool. The

worklight is activated when the trigger switch is depressed.

It will remain on for 2minutes. After 1 minute, 40 seconds,

the light will dim to 25% indicating that the light is going

to turn off.

LED Display (Fig. C)

The LED display on the top of the press tool includes the

power ON/OFF button

8

maintenance LED

17

, cycle

complete LED

18

, battery state of charge LED

19

, and

temperature LEDs

20

. Refer to the LED Indications chart

for specific information.

FIG. C

When the battery state of charge LED

19

is lit, regardless of

color, the tool is ON.

DeWALT

CRIMP CONNECT™ System (Fig. A)

This press tool is capable of connecting with a computer

via the micro USB port

9

on the back of the tool using the

micro USB cable included with your tool. This allows the

user to connect the

DeWALT

press tool to a computer which

utilizes

DeWALT

's CRIMP CONNECT

System software.

NOTE: The CRIMP CONNECT™ System software is governed

by separate terms and conditions available for viewing

through the software download.

Step 1: Download the CRIMP CONNECT™ System software

to your computer at www.dewalt.com/crimpconnect.

Step 2: Follow the instructions in the software to create

your CRIMP CONNECT™ System account.

Step 3: Connect your press tool with the

DeWALT

CRIMP

CONNECT™ System software by first connecting the

provided micro USB cable to the micro USB port

9

on the

back of the tool to a USB port on a computer. Then go to

the Home screen of the program to access tool tracking and

usage reports stored on the press tool.

NOTE: The USB connection will not charge the tool's

batterypack.

For more information on

WALT CRIMP CONNECT™ System

functionality and features, please call 1–800–4-

DeWALT

(1–800–433–9258), visit www.

DeWALT

.com or view the FAQ

page and help screens located inside the software.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.



WARNING: To reduce the risk of serious personal

injury, do not use the press tool with any kind

of accessory or attachment other than those

recommended by

DeWALT

Replacing the Press Jaw (Fig. D)

1. Remove the battery pack.

2. Hold the jaw

1

and move the lock/release slide

4

back.

The jaw retention pin

3

will automatically spring open,

releasing the jaw.



CAUTION: The jaw

1

will fall if the lock/release slide

4

is moved while the jaw is aimed downward.

3. Remove the press jaw or attachment.

4. Replace with a new or different sized press jaw or

attachment as shown in FigureD.

5. Push the jaw retention pin

3

back in until it locks in a

closed position.

NOTICE: To avoid damage to the tool, do not

operate the tool without the jaw retention pin

fully inserted. Damage to the tool may occur.

FIG. D

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.



WARNING: CUT OR AMPUTATION HAZARD. Never

have any part of your body near the press jaw or

moving parts during the press cycle, or whenever the

main power is ON. Serious personal injury may occur.



WARNING: Proper material preparation

and installation is the responsibility of the

installingcontractor.



WARNING: The press fittings must be used in

compliance with applicable building codes

and as approved by the authorities having

jurisdiction. For proper installation procedures

and to reduce the risk of failure resulting in injury or

property damage, follow all published safety and

installation instructions.



WARNING: To reduce the risk of injury, always

remove the press jaw or attachment for

transport or storage.

Installing and Removing the Battery Pack

(Fig. E)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

FIG. E

Proper Hand Position (Fig. F)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main handle

15

and one hand on the tool neck

16

, of the press tool.

FIG. F

Preparing the Connection



WARNING: Always follow the specific

manufacturer's installation instructions for press

tool attachments being used. It is the installer's

responsibility to ensure the compatibility of the pipe

and fittings used for the connection. Contact the

manufacturer for specific information on their fittings

system. Failure to follow all instructions and warnings

may result in property damage and/or serious

personalinjury.

• Make sure to clear the work area of loose debris and any

other items that could hinder the pressing operation.

• Always ensure the work area is set up properly and that

the tool's connection is prepared according to the fitting

manufacturer’s instructions.

• Follow the fitting manufacturer’s instructions to make

sure the tubing is inserted properly into the fitting.

Pressing (Fig. A, C)



WARNING: To reduce the risk of serious personal

injury, inspect the jaw assembly for cleanliness,

cracks or other damage before beginning a press.

Using a dirty or damaged jaw assembly could result

in improper press connections that could lead to

extensive property damage. Return damaged jaw

assembly to a

DeWALT

service facility.



WARNING: To reduce the risk of serious personal

injury, prior to use, inspect workpieces for cracks,

defects or wear. Defective workpieces may shatter.



WARNING: Before turning on the press tool, be

sure hands are clear of the jaws.

Before beginning a press, check the fuel gauge to determine

whether the battery charge is sufficient to complete the

pressing operation.

NOTE: The tool will turn off automatically after 2 minutes

of no use.

1. Press jaw arms

2

to open jaws

1

and place around

thefitting.

2. Turn the tool ON by holding the power ON/OFF button

8

until all 3 LEDs illuminate green.

3. Hold tool securely.

4. Press and hold the trigger switch

5

(bottom trigger)

until the cycle is complete, indicated by the ram

automatically returning to its original position.

5. When the press cycle is complete, the Cycle Complete

LED

18

will flash green for 5 seconds. If the press cycle

is incomplete, the cycle complete LED

18

will flash red

for 5 seconds. No action is possible until the user presses

the ON/OFF button.

6. If the battery dies or tool malfunctions during the press

connection, the rollers can retract by pressing the

reverse trigger switch

6

. This will retract the ram and

allow the jaws to be opened.

7. Press the ON/OFF button

8

to turn the tool OFF, then

press the jaw arms to open the jaw set.

NOTE: If the tool does not complete the press properly, read

the Troubleshooting Guide or LED Indications sections or

take the tool to a

DeWALT

factory service center.

NOTE: When pressing overhead, always confirm workpiece

and tool are secure before pressing.

NOTICE: In the event of an incomplete press, press the

reverse trigger switch

6

to open the press jaws and

remove the material.

Inspecting the Pressed Connection

1. Clear the pressed fitting of any control rings or control

labels. These are used by fitting manufacturers to

indicate an unpressed fitting.

2. Check for excessive misalignment, tubing not fully

inserted into the fitting, and incorrect jaw or attachment

alignment. Make sure no other issues are present on the

pressed connection per the manufacturer’s instructions.

If any issues are present, remove the fitting and replace

with a new one.

3. Test the fitting according to manufacturer’s instructions

or local codes.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.



WARNING: Before each use, inspect the tool

(including LED indicators) and correct any

problems before attempting to use.



WARNING: Skin injection hazard. The oil in the

mechanism is under extreme pressure. Do not

use hands to check for oil leaks.



WARNING: Explosion hazard. The internal

hydraulic system creates extreme pressures.

Only

DeWALT

-qualified personnel should service

thistool.

Required Maintenance (Fig. A)

Maintenance is required when the pipe pressing tool

reaches 45,000 cycles. Warning indicators will illuminate on

the diagnostic panel

7

as follows.

1. Maintenance warning at 44,500 cycles (Maintenance

LED lights yellow continuously)

2. Final maintenance warning at 44,900 cycles

(Maintenance LED flashes yellow continuously)

3. Needs service at 45,000 cycles (Maintenance LED lights

red for 10 seconds then turns tool off automatically).

At 45,000 cycles, the tool will no longer run. Take your

tool to a

DeWALT

factory service center for maintenance

andrecalibration.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Regularly clean the press jaws to be sure they are free of dirt

and debris to ensure a proper press.

Accessories



WARNING: Since accessories and attachments, other

than those offered or recommended by

DeWALT

have not been tested with this product, use of such

accessories or attachments with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories and attachments should

be used with thisproduct.

Recommended accessories and attachments for use with

your tool are available at extra cost from your local dealer or

authorized service center. If you need assistance in locating

any accessory or attachment, please contact

DeWALT

Industrial Tool Co., 701East Joppa Road, Towson, MD 21286,

call 1-800-4-

DeWALT

(1-800-433-9258) or visit our website:

www.dewalt.com.

For a complete and most up to date list of compatible jaws,

rings, attachments and fittings, visit www.dewalt.com.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement) should

be performed by a

DeWALT

factory service center

or a

DeWALT

authorized service center. Always use

identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from the

date of purchase. This warranty does not cover part failure

due to normal wear or tool abuse. For further detail of

warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-

DeWALT

(1-800-433-9258).

This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and

you may have other rights which vary in certain states

orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase. The press tool wear items such as rollers,

roller pins, and roller holder are not covered.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB606

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

SPECIFICATIONS

DCE200 20V Max*

Ram force 7645–8550 lbs (34kN-38kN)

Operating Temperature Range 14 °F–158 °F (-10 °C–70 °C)

Troubleshooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

Problem Possible Cause Possible Solution

Tool does not turn ON when power ON/OFF

switch is pressed.

Battery is not charged. Charge battery or use a new, fully charged battery.

Battery is not fully inserted into tool. Remove battery and reinsert fully into the tool.

Tool does not respond when trigger switch

is pressed.

Battery is too low to complete a crimp/press. Battery

LED lights in red continuously.

Recharge battery in compatible D

WALT charger.

Other causes Refer to LED Indications for additional

information.

Tool is plugged into computer via micro

USB cable but the maintenance LED does

not light blue continuously.

Micro USB cable is not the provided cable and may

only be a "charging" cable, not a "data" cable.

Use the provided data cable.

CRIMP CONNECT™ System software is not

working properly.

Other causes View the FAQ page and help screens located

inside the CRIMP CONNECT™ System software.

LED Indications

INDICATION USER ACTION LEDs EXAMPLE

Unit Power

Unit ON Press ON/OFF button All 3 LEDs light in green for 1 second.

GREEN

Unit OFF Press ON/OFF button All 3 LEDs light in red for 1 second.

RED

USB

Plug tool into computer

via USB

Maintenance LED lights in blue continuously.

NOTE: Indication is permanent as soon as tool is plugged in via USB.

BLUE

Battery

Full Charge Battery LED lights in green continuously.

NOTE: Indication is permanent as soon as tool is switched on.

GREEN

Medium

Charge

Battery LED lights in yellow continuously.

NOTE: Indication is permanent as soon as tool is switched on.

YELLOW

Low Charge Battery LED lights in red for 10 seconds, then tool turns off automatically.

NOTE: Indication is permanent as soon as tool is switched on.

RED

Crimp/Press Cycle

Cycle

Complete

Attempt a crimp/press Cycle Complete LED flashes in green for 5 seconds.

GREEN

Cycle Not

Complete

Attempt a crimp/press Cycle Complete LED flashes in red for 5 seconds.

NOTE: No action is possible until user presses ON/OFF button.

RED

Maintenance

Warning

Maintenance LED lights in yellow continuously.

NOTE: 500 cycles left. Indication is permanent as soon as tool is

switched on.

YELLOW

Final

Maintenance

Warning

Maintenance LED flashes in yellow continuously.

NOTE: 100 cycles left. Indication is permanent as soon as tool is

switched on.

YELLOW

Needs Service Maintenance LED lights in red for 10 seconds, then tool turns

off automatically.

NOTE: 0 cycles left.

RED

Temperature

Out of Range

Maintenance and Cycle Complete LEDs light in red continuously.

NOTE: Indication is permanent as soon as tool is switched on.

LEDs turn off when acceptable temperature is reached.

RED

Mâchoires de sertissage

Bras de mâchoires

Broche de retenue

Glissière de verrouillage

Gâchette

Inverseur

Écran de diagnostic

Interrupteur marche/

arrêt

Port micro USB

Bloc-piles

Bouton de libération du

bloc-piles

Anneau de suspension

de la bandoulière

Lampe DEL

Dispositif de fixation de

la bandoulière

Poignée principale

Collet

FIG. A

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Pour toute question ou remarque au sujet de cet outil

ou de tout autre outil

DeWALT

, composez le numéro

sans frais : 1-800-4-

DeWALT

(1-800-433-9258).

Français (traduction de la notice d’instructions originale)

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

POUR LES OUTILS ÉLECTRIQUES



AVERTISSEMENT! Lire toutes les consignes de

sécurité, les directives, les illustrations et les

caractéristiques techniques fournies avec cet

outil électrique. Tout manquement aux instructions

suivantes pose des risques de chocs électriques,

d’incendie et/ou de dommages corporels graves.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise à

l’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc électrique est plus élevé si votre corps

est mis à laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive.

Ne jamais utiliser le cordon pour transporter,

tirer ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à

l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue

pour l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique

est utilisé. Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence de drogues,

d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut

entraîner des blessures corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source

d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter

un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de

provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les

situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

h ) Ne pas laisser la familiarisation gagnée par

l’utilisation fréquente des outils vous amener

à la négligence et à ignorer les principes de

sécurité liés à l’outil. Une imprudence pourrait

causer des dommages corporels graves en une

fraction de seconde.

4) Utilisation et entretien d’un outil

électrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

b ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et

doit êtreréparé.

c ) Débrancher la fiche de la source d’alimentation

et/ou du bloc-piles de l’outil électrique avant de

faire tout réglage ou changement d’accessoire

ou avant de ranger l’outil. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

e ) Entretien des outils électriques. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus

faciles àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les

forets, etc. conformément aux présentes

directives en tenant compte des conditions de

travail et du travail à effectuer. L’utilisation d’un

outil électrique pour toute opération autre que celle

pour laquelle il a été conçu estdangereuse.

h ) Maintenir les poignées et les surfaces de

préhension propres et sèches, exemptes

d’huile ou de graisse. Des poignées ou surfaces

de préhension glissantes ne permettent pas la

manipulation sécuritaire et le contrôle de l’outil dans

les situations inattendues.

5) Utilisation et entretien du bloc-piles

a ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc-piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de b loc-piles.

b ) Utiliser les outils électriques uniquement avec

les blocs-piles conçus à cet effet. L’utilisation de

tout autre bloc-piles risque de causer des blessures ou

unincendie.

c ) Lorsque le bloc-piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court-circuit des bornes du bloc-piles

risque de provoquer des brûlures ou unincendie.

d ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc-piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc-piles peut provoquer

des irritations ou desbrûlures.

e ) Ne pas utiliser un bloc-piles ou un outil

endommagé ou modifié. Un bloc-piles endommagé

ou modifié pourrait se comporter de façon

imprévisible et poser des risques d’incendie, d’explosion

ou de dommages corporels.

f ) Ne pas exposer un bloc-piles ou un outil au feu,

ou à des températures excessives. Toute exposition

au feu ou à des températures supérieures à 130°C

pose des risques d’explosion.

g ) Suivre toutes les instructions de chargement

et ne pas recharger un bloc-piles ou un outil

hors des températures d’emploi spécifiées

dans les directives. Un chargement incorrect

ou à des températures hors des plages spécifiées

pourrait endommager le bloc-piles et augmenter les

risquesd’incendie.

6) Réparation

a ) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de

rechange identiques. Cela permettra de maintenir

une utilisation sécuritaire de l’outilélectrique.

b ) Ne jamais réparer un bloc-piles endommagé.

Toute réparation d’un bloc-piles devrait être effectuée

par le fabricant ou des services agréés.

Règles de sécurité additionnelles propres

aux outils de sertissage



AVERTISSEMENT: utiliser l’outil de sertissage

exclusivement avec des accessoires

DeWALT

agréés par

DeWALT

. Toute utilisation de l’outil de

sertissage à d’autres fins que pour sa fonction

d’origine ou sa modification pour d’autres

applications pose le risque d’endommager

l’outil et ses accessoires, et/ou résulter en une

installation défectueuse. Les installations

défectueuses posent des risques de défaillances

extrêmement graves, de dommages corporels

pour les installateurs et de dommages matériels.



AVERTISSEMENT: bien que cet outil de

sertissage

DeWALT

atteindra la pression

adéquate pour effectuer au mieux le sertissage,

le sertissage ne sera correctement effectué que

dans la mesure où la connexion ne sera affectée

d’aucun défaut et que l’outil sera préparé

conformément à la procédure d’installation

du raccord du fabricant. La préparation et

l’installation correctes restent la responsabilité

de l’entrepreneur chargé de l’installation.

• Utiliser exclusivement des accessoires

DeWALT

, ou

agréés par

DeWALT

, capables de subir les taux de

compression conformes à la plaque signalétique

del’outil.

• Protéger toutes les parties du corps des accessoires

pendant l’utilisation de l’outil et tant que l’outil sera

en marche. Tout moment d’inattention pendant

l’utilisation d’un outil électrique pose des risques de

blessures graves. Les doigts ou les mains pourraient être

écrasés, ou subir fractures ou amputation s’ils venaient à

entrer en contact avec les accessoires.

• Vérifier l’outil et ses accessoires avant toute

utilisation. Ne jamais tenter de réparer ou utiliser

un dispositif de mâchoires ou tout autre accessoire

endommagé. Changer le dispositif de mâchoires ou

l’accessoire.

• Cet outil produit des forces importantes qui

pourraient briser les accessoires ou les pièces et

causer des dommages corporels. Rester attentif et

prendre les mesures de sécurité adéquates, y compris le

port d’une protection oculaire.

• Risques d’écrasement. Ne jamais mettre l’outil en

marche sans son dispositif de mâchoires ou un

accessoire installé.

• Cet outil ne doit être utilisé que par du

personnelqualifié.

• Avant chaque utilisation, vérifier l’outil et les

voyants DEL sur l’écran de diagnostic. Corriger tout

problème avant d’utiliser l’outil. Se reporter aux sections

Guide de dépannage ou Voyants DEL pour avoir la

liste des problèmes possibles et leurs solutions.

• Avant chaque utilisation, vérifier que les lieux de

travail ne comportent aucun risque, y compris

l’absence de produits chimiques ou déchets dans

lestuyaux.

• Avant toute utilisation, lire et comprendre toutes

les instructions quant à la sécurité et à l’utilisation,

y compris les instructions d’installation du raccord

du fabricant et les instructions accompagnant tout

accessoire utilisé avec cet outil. Tout manquement

aux instructions et avertissements pose des risques

de dommages matériels et/ou corporels graves.

• Éloigner de la zone de sertissage les mains et tout

autre objet pendant toute la durée d’utilisation de

l’outil. Il y a risques d’écrasement pour les doigts.

• Arrimer et soutenir le matériau avant d’effectuer

le sertissage pour prévenir tout mouvement

pendantl’opération.

• Maintenir systématiquement l’outil fermement.

Lesforces appliquées sur l’outil peuvent changer pendant

ou après le sertissage.

• Le sertissage peut faire que des débris de matériau

s’envolent. Des particules volantes pourraient

occasionner des dommages oculaires permanents. Porter

SYSTÉMATIQUEMENT une protection oculaire.

• Porter systématiquement des gants pendant

l’utilisation de l’outil et pour manipuler les

matériaux. Les extrémités des matériaux peuvent

être acérées et poser des risques de dommages

corporelsgraves.

• Porter systématiquement des souliers de sécurité

pour protéger les pieds de tout débris métallique

acéré tombé sur le sol.

Consigne de sécurité supplémentaire



AVERTISSEMENT: porter SYSTEMATIQUEMENT

des lunettes de protection. Les lunettes courantes

NE sont PAS des lunettes de protection. Utiliser aussi

un masque antipoussières si la découpe doit en

produire beaucoup. PORTER SYSTÉMATIQUEMENT UN

ÉQUIPEMENT DE SÉCURITÉ HOMOLOGUÉ:

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);

• Protection auditive ANSI S12.6 (S3.19);

• Protection des voies respiratoires NIOSH/OSHA/

MSHA.



AVERTISSEMENT: les scies, meules, ponceuses,

perceuses ou autres outils de construction peuvent

produire des poussières contenant des produits

chimiques reconnus par l’État californien pour causer

cancers, malformations congénitales ou être nocifs au

système reproducteur. Parmi ces produits chimiques,

on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment,

ou autres produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un

traitementchimique.

Le risque associé à de telles expositions varie selon la

fréquence à laquelle on effectue ces travaux. Pour réduire

toute exposition à ces produits: travailler dans un endroit

bien aéré, en utilisant du matériel de sécurité homologué, tel

un masque antipoussières spécialement conçu pour filtrer les

particulesmicroscopiques.

• Limiter toute exposition prolongée avec les

poussières provenant du ponçage, sciage, meulage,

perçage ou toute autre activité de construction.

Porter des vêtements de protection et nettoyer à

l’eau savonneuse les parties du corps exposées. Le

fait de laisser la poussière pénétrer dans la bouche, les

yeux ou la peau peut favoriser l’absorption de produits

chimiquesdangereux.



AVERTISSEMENT: cet outil peut produire et/

ou répandre de la poussière susceptible de causer

des dommages sérieux et permanents au système

respiratoire. Utiliser systématiquement un appareil

de protection des voies respiratoires homologué par

le NIOSH ou l’OSHA. Diriger les particules dans le sens

opposé au visage et aucorps.



AVERTISSEMENT: pendant l’utilisation, porter

systématiquement une protection auditive

individuelle adéquate homologuée ANSI S12.6

(S3.19). Sous certaines conditions et suivant la durée

d’utilisation, le bruit émanant de ce produit pourrait

contribuer à une perte de l’acuitéauditive.



ATTENTION: après utilisation, ranger l’outil

sur son côté, sur une surface stable, là où il

ne pourra ni faire trébucher ni faire chuter

quelqu’un. Certains outils équipés d’un large bloc-

La page charge ...

DeWalt DCE200 Mode d'emploi

Marque: DeWalt

Modèle: DCE200

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCE200 User guide
español: DeWalt DCE200 Guía del usuario

DeWalt DCE200 Mode d'emploi

Ce manuel convient également à

DeWalt DCE200 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents