Powerfist 9049057 Le manuel du propriétaire

Marque: Powerfist

Modèle: 9049057

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

V1.0 9049057

Please read and understand all instructions before use. Retain this manual for

future reference.

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Voltage Rating (V DC) 20

Stroke Length (in.) 1-1/8

Strokes Per Minute (SPM) 0 to 2,900

Blade Type T-shank

Material Plastic/metal

Handle Type D with soft grip

Keyless Blade Clamp Yes

Adjustable Shoe Yes

Tool Length (in.) 15.75

Weight (lb) 4.63

Includes (1 ea) Wood and metal blade

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A

notice is an alert that there is a possibility of property damage, injury or

death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that

may result in minor or moderate injury if proper practices are

not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice

will result in equipment or property damage, but not

personal injury.

V1.0 20V Li-ion Cordless Reciprocating Saw 9049057

Visit www.princessauto.com for more information 3

INTRODUCTION

This cordless reciprocating saw features a high-performance motor, metal

gear construction, variable-speed trigger, keyless blade changes, adjustable

pivoting shoe and textured grip. It requires the Powerfist 20V cordless

system Li-ion battery and charger (sold separately).

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection

and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions. Place lights so you are not working in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away from

the work area.

3. Store unused tools properly in a safe and dry location to prevent rust

or damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. Wear the appropriate type of full-face shield in addition to safety

googles, as the work can create chips, abrasive or particulate matter.

3. Do not wear gloves when operating a tool that can snag the material

and pull the hand into the tool.

4. Wear protective clothing designed for the work environment and tool.

5. Non-skid footwear is recommended to maintain footing and balance in

the work environment.

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

4 For technical questions call 1-800-665-8685

6. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

7. Wear the appropriate rated dust mask or respirator.

8. This tool can cause hearing damage. Wear hearing protection gear with

an appropriate Noise Reduction Rating to withstand the decibel levels.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

4. Securely hold this tool using both hands. Using a tool with only one

hand can result in loss of control.

POWER TOOL PRECAUTIONS

1. Do not use any power tool with a malfunctioning power switch or

control. A power tool that fails to respond to the controls is dangerous

and can cause an injury. A qualified technician must repair and verify

the power tool is operating correctly, before it can be used.

2. Do not cover the air vents. Proper cooling is necessary prevent damage

to the tool’s motor.

3. Avoid unintentional starts. Ensure the switch is off when connecting to

the power source.

4. Disconnect the power source before installing or servicing the tool.

5. Remove adjusting keys and wrenches before using the tool. The tool

may eject an attached wrench or a key and cause an injury to you or

a bystander.

6. Never point the tool towards yourself. It could inflict an injury.

7. Never force the tool. Excessive pressure could break the tool, resulting

in damage to your workpiece or serious personal injury. Excessive

pressure is the cause if your tool runs smoothly under no load, but

roughly under load.

V1.0 20V Li-ion Cordless Reciprocating Saw 9049057

Visit www.princessauto.com for more information 5

8. Keep hands and fingers away from the work area. Any part of the body

contacting the tool’s working parts could result in an injury.

9. Only use accessories that are specifically designed for use with the

tool. Ensure the accessory is tightly installed.

10. Only use an accessory that exceeds the Speed Rating (see Specifications).

11. Before using the tool on a workpiece, test the tool by running it at the

highest Speed Rating for at least 30 seconds in a safe position. Stop

immediately if there is any abnormal vibration or wobbling. Check the

tool to determine the cause.

a. Do not allow the tool to run without load for an extended period

of time, as this will shorten its life.

12. Never touch the tool accessory or workpiece during or immediately after

use. They may be hot and could inflict a burn injury.

13. Take work breaks to prevent the tool's motor from overheating

and/or overloading.

14. Never use a tool with a cracked or worn tool accessory. Change the

tool accessory before using it.

15. Do not start the tool when the tool’s accessory is touching the workpiece.

ELECTRICAL SAFETY

WARNING! Do not touch or handle a live tool with any part of your body that

is wet or damp. Wet skin reduces resistance to electrical current, increasing

the danger of a serious or fatal shock.

1. Do not alter any parts of the tool or accessories. All parts and

accessories are designed with built-in safety features that may be

compromised if altered.

2. Protect yourself against electric shocks when working on electrical

equipment. Avoid body contact with grounded surfaces. There is an

increased chance of electrical shock if your body is grounded.

3. Do not expose the saw to rain, snow, frost or any other damp or wet

conditions. Water entering a tool will increase the risk of electric shock.

4. Hold the tool by the insulated gripping surfaces when performing an

operation where the cutting accessory may contact hidden wiring.

Contact with a live wire will also make exposed metal parts of the

power tool live and shock the operator.

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

6 For technical questions call 1-800-665-8685

BATTERY SAFETY

WARNING! Only charge a battery with a charger designed for that purpose. Do

not use modified chargers or a charger that does not specify the voltage,

amperage or recharge rate. Improper charging can lead to battery rupturing.

WARNING! Do not charge a damaged or frozen battery. Contact your local

municipality for proper disposal procedures. Consult the Safety Data

Sheet (SDS) for your battery before use or maintenance.

1. Do not expose the battery to heat or throw it in a fire. The contents are

flammable and the battery may explode. Remove any source of ignition

such as an open flame or a tool like a heater from the area.

2. Do not inhale smoke issuing from a burning battery, as it is toxic.

3. Do not disassemble or crush the battery as the contents are corrosive

and flammable. Exposure may cause an injury. There is a risk of

escaping hazardous vapors. These vapors can irritate the respiratory

track. Always ensure proper ventilation and immediately consult a

doctor, if you feel unwell.

4. Even a discharged battery may still carry a charge. To prevent a shock,

place battery terminal caps or covers over the terminal to prevent

accidental contact. Hold the battery by the bottom if moving the

battery to a different location.

5. Do not store the battery in containers / spaces with loose metal

objects. Keep it away from other metal objects that can make a

connection between terminals. Shorting out the battery terminals may

cause burns or a fire.

6. A battery-operated tool with internal batteries or with a separate

battery pack must only be powered by the included battery. Do not

mix different brands of tools and batteries or use adapters to allow

you to use a battery pack with a different voltage. This can damage the

tool’s electrical mechanism and create a fire hazard.

7. If fluids leak from the battery, avoid contact. Leaking battery fluid can

cause irritation of the skin or burns. If contact should occur, flush

immediately with water. In case of accidental contact with the eyes,

seek medical aid.

8. Do not disconnect from the power source in place of using the ON/OFF

switch on the tool. This can lead to an accidental startup when the tool

is connected to the power supply.

V1.0 20V Li-ion Cordless Reciprocating Saw 9049057

Visit www.princessauto.com for more information 7

9. Do not allow a rechargeable battery to fully discharge. This will

damage the battery. Recharge the battery as soon as possible.

10. Do not store the battery completely discharged. Charge it fully before

storing. Recharge occasionally if storing for a long time.

CHARGER PRECAUTIONS

WARNING! Voltage is present at the charging terminals, do not probe with

conductive objects. Electric shock or electrocution may result. A battery

short can cause a large current flow, overheating, possible burns and even a

breakdown of the tool.

Before using the charger, read all instructions and cautionary markings on

the charger, battery pack and the product using the battery pack.

1. Only use the included battery charger to recharge the battery. Other

chargers may be unsafe, causing an electrical short circuit or fire.

2. Disconnect the charger from its power source before attaching or

removing batteries or battery clamps.

3. Charge the battery in a well-ventilated area and never obstruct the

vents in the top and bottom of the charger. Place the charger on a flat

nonflammable surface and away from flammable materials when re-

charging the battery.

4. Do not place any object on top of the charger or place the charger on a

soft surface that may result in excessive internal heat. Place the

charger in a position away from any heat source.

5. Charge the battery at rates recommended by the battery manufacturer.

6. Do not insert the battery into the charger backwards. Make sure the

polarity symbols on the battery lines up with the polarity symbols of

the charger. A battery inserted backwards may explode causing fire

and/or injury.

7. Do not use the charger with an extension cord. This can cause a low

voltage outage during charging.

8. Do not charge leaking batteries. A compromised casing will release

volatile chemicals and gases. Charging a leaking battery can cause a

fire or explosion.

9. Do not operate the charger if it has received a sharp blow, been dropped

or otherwise damaged in any way. Have it serviced or replaced.

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

8 For technical questions call 1-800-665-8685

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific

function. Do not modify or alter this tool or use it for an

unintended purpose.

2. Do not use the tool if any parts are damage broken or misplaced.

Repair or replace the parts.

CUTTING PRECAUTIONS

WARNING! Some surfaces contain materials which can be toxic. When

working on materials that may contain lead, asbestos, copper chromium

arsenate or other toxic materials, extra care should be taken to avoid

inhalation and minimize skin contact.

1. Only use accessories that are specifically designed for use with the

tool. Ensure the accessory is tightly installed.

2. Use caution when cutting damp wood, pressure treated lumber or

wood containing knots. Adjust speed of cut to maintain smooth

advancement of tool without decrease in cutting accessory speed.

3. Do not use a dull or damaged cutting accessory. A dull cutting accessory

requires more force to use the tool, possibly causing the accessory to

break. This may cause an injury and will damage the workpiece.

a. Dull or improperly set cutting accessories produce a narrow kerf

that can cause excessive friction on the cutting accessory,

resulting in binding or a kickback. Keep the cutting accessory’s

edge sharp and clean.

4. Only use a cutting accessory that exceeds the No Load Speed

rating (see Specifications).

5. Always wait until the motor has reached full speed before starting a cut.

CUTTING TOOL PRECAUTIONS

1. Use the correct mounting hardware. The mounting hardware is

designed to hold the cutting accessory on the tool to allow optimum

performance and safety of operation. Mismatched mounting hardware

may result in a tool malfunction and cause an injury.

a. Always use blades that are correctly sized and shaped for the

tool. Blades that do not match the tool’s mounting hardware will

run erratically, causing loss of control.

V1.0 20V Li-ion Cordless Reciprocating Saw 9049057

Visit www.princessauto.com for more information 9

2. Check the cutting accessory for damage before each use. A damaged

accessory can break during use and cause serious injury.

3 Inspect material for foreign objects such as staples, nails or debris.

Remove from material before cutting.

4. Affix the workpiece to a stable platform to prevent movement, minimize

body exposure to injury, cutting accessory binding or loss of control.

5. Position the tool on the larger section of a supported workpiece to

complete a cut. Cut the small portion away from the larger portion.

Support the smaller portion if possible to prevent it from binding when

the cut is almost complete.

6. Never confine the part of the workpiece being cut away by holding,

clamping or using length stops against it. That part of the workpiece

could become wedged against the blade and be thrown violently. The

cut away part of the workpiece must be free to move sideways

RECIPROCATING SAW PRECAUTIONS

DANGER! When the tool is in operation, keep hands away from the saw

blade and the area it is being applied to. Failure to follow this warning will

result in amputation, serious personal injury or death.

1. Always make sure the reciprocating saw is clean before using.

2. Always handle the reciprocating saw blade with care when mounting

or removing it.

3. Always be aware of the position of your hands relative to the blade.

Avoid awkward hand positions where a sudden slip could cause a hand

to move into the blade.

4. Never reach behind or beneath the blade.

KICKBACK PRECAUTIONS

Kickback is a sudden reaction to a pinched or snagged cutting accessory.

The tool kicks out and away from the workpiece while the cutting accessory

is still active. This can inflict a serious injury on the user or a bystander.

Kickback can also damage the tool or workpiece.

Kickback can be avoided by taking proper precautions:

1. Maintain a firm grip on the tool and position your body and arms to

allow you to resist a kickback. Kickback will propel the tool in the

direction opposite to the cutting accessory’s teeth or direction of

rotation. A snagged rotary cutting bit may pull the tool out of the grasp

of the user.

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

10 For technical questions call 1-800-665-8685

2. If kickback occurs:

a. The cutting accessory may pass over a body part, causing a

seriously injury;

b. A rotary bit may wrench the user’s arm causing muscle or joint

injuries; and

c. The tool may strike bystanders.

3. Use clamps or a vice to hold down smaller workpieces.

4. Use special care when working on corners, sharp edges or flexible

material. These workpieces have a tendency to snag the

cutting accessory.

5. When the blade is the binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless in the material

until the blade comes to a complete stop. Never attempt to remove the

saw from the workpiece or pull the saw backward while the blade is in

motion as kickback may occur. Investigate and take corrective actions

to eliminate the cause of blade binding.

6. When restarting a saw in the workpiece, center the saw blade in the

kerf and check that saw teeth are not engaged into the material. If saw

blade is binding, it may walk up or kickback from the workpiece as the

saw is restarted.

7. Support large panels to minimize the risk of blade pinching and

kickback. Large panels tend to sag under their own weight. Supports

must be placed under the panel on both sides, near the line of cut and

near the edge of the panel.

8. Use extra caution when making a plunge cut into existing walls or other

blind areas. The protruding blade may cut objects that can cause kickback.

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to

vibration may cause temporary or permanent physical injury. Take

frequent breaks when using the tool.

2. If you feel any medical symptoms related to vibrations (such as

tingling, numbness, and white or blue fingers), seek medical attention

as soon as possible.

3. Wear suitable gloves to reduce the effects of vibration.

4. DO NOT use this tool before consulting a physician if one of the

following applies:

V1.0 9049057

Please read and understand all instructions before use. Retain this manual for

future reference.

a. Pregnant

b. Impaired blood circulation

to the hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud's Disease

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the Identification Key are included.

IDENTIFICATION KEY

A Trigger

B Trigger Lock

C Battery (sold

separately)

D Pivoting Shoe

E Blade

F Chuck

G LED Work Light

H Shoe Lock

ASSEMBLY &

INSTALLATION

Letter references in

parenthesis (A) refer to the

included Identification Key.

INSTALL EXTERNAL BATTERY PACK

WARNING! Avoid unintentional starts by ensuring the trigger lock (B) is

engaged before installing the battery pack.

1. Check the battery power level before each use.

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

12 For technical questions call 1-800-665-8685

a. The battery is not fully charged out of the carton. Charge the

battery before first use.

2. Install the battery by aligning the rib on the battery with the groove

on the battery port and push forward until the latch clicks.

3. Remove the battery by pushing the battery lock button and pulling the

battery free.

INSTALLING THE BLADE

IMPORTANT! Coarse blades are ideal for cutting wood, plastics and

composites. Fine blades are ideal for cutting metal. When cutting metal,

lightly oil the blade to prevent it from overheating.

1. Twist the chuck (F) counterclockwise to open.

2. Insert the blade (E) into the chuck.

3. Release the chuck to close.

4. Ensure that the blade is securely locked and that the teeth are

pointing downwards.

ADJUSTING THE PIVOTING SHOE LENGTH

1. Move the shoe lock (H) into the unlocked position.

2. Pull the shoe assembly into or away from the housing until it reaches

the desired length.

3. Move the shoe lock into the locked position.

OPERATION

WARNING! Do not attempt

to cut a workpiece that is

thicker than a fully

retracted blade. This

prevents the blade from

striking the workpiece and

shattering from the impact.

Refer to Fig. 1.

1. Hold the

reciprocating

saw firmly with both hands. Position the blade near the work piece.

2. Push in and hold the trigger lock (B), then press the trigger (A).

3. Allow the blade to reach full speed before contacting the workpiece.

Fig. 1

PVC Pipe

✓

PVC Pipe

V1.0 20V Li-ion Cordless Reciprocating Saw 9049057

Visit www.princessauto.com for more information 13

4. Press the pivoting shoe assembly against the surface to be cut. Align

the saw blade along the direction of the cut. Slowly tilt the saw

forward to lower the blade into the workpiece.

WARNING! Do not bend or twist the blade or attempt to cut with the tip as it

may cause kickback and blade damage.

IMPORTANT! Use a fine blade or cut at a higher speed if chattering or

vibration occurs. Replace the blade if the saw overheats or clogs.

5. After completing the cut, release the trigger.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier

to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or

worn components. Only use identical replacement parts when servicing.

3. Only use accessories intended for use with this tool.

4. Keep the tool handles or gripping surfaces clean and dry.

5. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd.

for replacements.

6. Clear the vents of any dirt, dust and debris on a regular basis to

prevent the tool from overheating.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

BATTERY MAINTENANCE

Avoid the risk of battery short circuits during transport, storage or disposal

by isolating both terminals with adhesive tape or pack the battery in a

plastic bag or a cardboard box.

1. The longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 50 to

86°F (10 to 30°C). Do not charge the battery when the temperature is

below 32°F (0°C) or above 104°F (40°C). This is important and will

prevent damage to the battery pack.

2. Charge the battery at rates recommended by the manufacturer.

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

14 For technical questions call 1-800-665-8685

CLEANING

1. Remove all swarf from the machine with a vacuum cleaner or

compressed air. Focus on removing dust from the motor’s fan vents.

2. Thoroughly clean all surfaces.

CLEANING THE CHARGER

1. Only clean with a damp cloth. Avoid using solvents when cleaning

plastic parts.

2. To reduce risk of electric shock, unplug the charger from the outlet

before attempting any cleaning. Removing the battery pack will not

reduce this risk.

STORAGE

When not in use for an extended period, apply a thin coat of lubricant to the

steel parts to avoid rust. Remove the lubricant before using the tool again.

1. Components should be kept dry, with machined surfaces lightly oiled.

2. Always remove the saw blade and store in a safe place.

3. Never store equipment in a wet/damp environment.

BATTERY STORAGE

Remove the battery when not in use for an extended period of time to

prevent damage.

1. Do not store the battery completely discharged. Charge it fully before

storing. Recharge occasionally if storing for a long time.

2. Do not store batteries in containers / spaces with loose metal objects.

Battery terminals could be short circuited if they come into contact

with metal objects. In addition to damaging the battery, you increase

the risk of a fire.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

V1.0 20V Li-ion Cordless Reciprocating Saw 9049057

Visit www.princessauto.com for more information 15

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function

properly or parts are missing. If unable to do so, have a qualified technician

service the tool.

Problem(s) Possible Cause(s) Suggested Solution(s)

The saw will not

start.

Supplied power is

interrupted.

2. On/Off switch is faulty.

3. Motor components are

short-circuiting or are

defective.

4. Motor has overheated.

5. The battery is not

installed correctly.

6. Battery power

depleted.

7. Battery is worn out.

Check that power supply is

still available.

2. Replace faulty switch.

3. Have a qualified technician

service the tool.

4. Allow motor to cool before

attempting to use.

5. Clean battery contacts

individually to avoid a shock.

Then install the battery

correctly. Make sure the

polarity matches and the

battery locks into place.

6. Follow instructions to charge

the battery in Care &

Maintenance.

7. Replace with a new battery

from the same manufacturer.

Dispose or recycle your old

battery according to your

local municipal bylaws.

Motor starts slow

and doesn't reach

operation speed.

1. Motor is damaged.

2. The battery has

insufficient charge.

3. Battery is worn out.

1. Have a qualified technician

service the tool.

Follow instructions to charge

the battery in Care &

Maintenance.

3. Replace with a new battery

from the same manufacturer.

Dispose or recycle your old

battery according to your

local municipal bylaws.

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

16 For technical questions call 1-800-665-8685

Tool is making

unusual sounds

The saw's parts may

be rubbing or binding.

2. Electrical components

may be shorting.

Check for obstructions or

misaligned tool components.

Lubricate, repair or replace

the components based on

the particular problem.

2. Disconnect tool from the

power source immediately.

Have the tool examined by a

qualified technician.

Heavy sparking

inside motor

housing.

Motor is shorting. Disconnect tool from the power

source immediately. Have the tool

examined by a qualified

technician.

Overheating 1.

Forcing machine to

work too fast.

Blocked motor housing

vents.

Allow machine to work at its

own rate.

2. Keep the blade sharp.

Replace as needed

3. Blow dust out of motor using

compressed air.

V1.0 20V Li-ion Cordless Reciprocating Saw 9049057

Visit www.princessauto.com for more information 17

PARTS BREAKDOWN

PARTS LIST

# DESCRIPTION QTY

1 Saw Blade 1

2 Reciprocating Rod

Subassembly

3 Front Positioning Block 1

4 Rear Positioning Block 1

5 Oil Bearing 1

6 Dustproof Block 1

7 Screw 13

8 Spring Washer 4

9 Gear Box Cover 1

10 Needle Bearing 1

11 Roller Pin 1

12 Positioning Block for Shaft 1

13 Balance Block 1

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

18 For technical questions call 1-800-665-8685

14 Central Axis 1

15 Roller Pin 1

16 Gear Wheel 1

17 Flat Washer 2

18 Bearing 1

19 Circlip for Hole 1

20 Bearing 1

21 Flat Washer 2

23 Left Enclosure 1

24 Return Spring for Push Rod 1

25 Push Rod 1

26 Switch 1

27 Battery Bracket

Subassembly

28 Motor 1

29 Motor Bracket 1

30 Bearing 1

31 Spring Washer 3

32 Screw 2

33 Flat Washer 1

34 Small Washer 1

35 Roller Pin 4

36 Roller Pin 1

37 Gear Box 1

38 Limit Piece 1

39 Pivoting Shoe 1

40 Sealing Strip 2

41 Shoe Lock 1

42 Circlip for Shaft 1

43 Positioning Axis 1

45 Positioning Frame 1

46 Flat Washer 1

47 Screw 1

48 Right Enclosure 1

49 Red Inner Wire 1

50 Black Inner Wire 1

51 Tapping Screw 11

V1.0 20V Li-ion Cordless Reciprocating Saw 9049057

Visit www.princessauto.com for more information 19

9049057 20V Li-ion Cordless Reciprocating Saw V1.0

20 For technical questions call 1-800-665-8685

La page charge ...

Powerfist 9049057 Le manuel du propriétaire

Marque: Powerfist

Modèle: 9049057

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Powerfist 9049057 Owner's manual

Powerfist 9049057 Le manuel du propriétaire

Powerfist 9049057 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents