La-Z-Boy 10U502 Manuel utilisateur

Taper
Manuel utilisateur
operating instructions
instrucciones de operación
instructions
© 2020 La-Z-Boy Incorporated D0C016530 08/20
Power Recliner with Headrest,
Power Recliner with Headrest and Lumbar,
Power Sofa with Headrest and
Power Sofa with Headrest and Lumbar Furniture
Sillón reclinable eléctrico con apoyacabezas, sillón
reclinable eléctrico con mecanismo lumbar y
apoyacabezas, so eléctrico con apoyacabezas, y sofá
eléctrico con mecanismo lumbar y de apoyacabezas
Fauteuil inclinable électrique avec repose-te, fauteuil
inclinable électrique avec repose-tête et support lombaire,
canainclinable électrique avec repose-tête et canapé
inclinable électrique avec repose-tête et support lombaire
Congratulations!
You are now the proud owner of a
stat e-of-the-art Power Recliner with Headrest,
Power Recliner with Headrest and Lumbar,
Power Sofa with Headrest and Power Sofa with
Headrest and Lumbar furniture by La-Z-Boy.
You have just selected one of the
finest quality upholstered products
produced in the furniture industry,
backed by over 90 years of quality
manufacturing experience.
La-Z-Boy®is proud of our designs
and craftsmanship and knows you
will feel the same as you enjoy your
new furniture’s comfort and style.
3
2
Table of Contents
Important Safety Instructions ...................................... 4-5
Regulatory Compliance Statements....................................6
Power Recliner with Headrest Assembly Instructions.......8-9
Power Recliner with Headrest and Lumbar
Assembly Instructions................................................10-11
Power Sofa with Headrest Assembly Instructions..........12-15
Power Sofa with Headrest and Lumbar
Assembly Instructions................................................16-19
Battery Backup Assembly Instructions..................................20
Operating Instructions for Power Recliner with Headrest
with Standard Control Panel..................................................22-24
Operating Instructions for Power Recliner with Headrest
and Lumbar with Standard Control Panel..............................26-28
Operating Instructions for Power Sofa with Headrest
with Standard Control Panel..................................................30-32
Operating Instructions for Power Sofa with Headrest
and Lumbar with Standard Control Panel..............................34-36
Operating Instructions for Power Recliner with Headrest
with Optional Wireless Remote..............................................38-39
Operating Instructions for Power Recliner with Headrest
and Lumbar with Optional Wireless Remote.................40-41
Operating Instructions for Power Sofa with Headrest
with Optional Wireless Remote...................................42-43
Operating Instructions for Power Sofa with Headrest
and Lumbar with Optional Wireless Remote.....................44-45
Operating Instructions for Optional Wireless Remote.............46-49
Troubleshooting.....................................................................50-51
Furniture Placement Guide.................................................52
IMPORTANT
Read the safety and other instructions before using your
Power Recliner with Headrest, Power Recliner with Headrest and
Lumbar, Power Sofa with Headrest and Power Sofa with Headrest
and Lumbar furniture. Keep this manual for future reference. Disclaimer: The information and products featured in this manual may be
somewhat different from the product you purchased. La-Z-Boy reserves the right
to make substitutions that are equal in quality and performance.
5
4
To reduce the risk of electric shock, serious injury or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this unit if the
power control is damaged, wet, in contact with or near spilled water or any liquid. Do not use the
unit if the button activation switch has been exposed to water or any liquid. Do not handle the
plug or remote control with wet hands.
To prevent suffocation, keep plastic bags away from children.
Keep cord out of the reach of children and pets that may cause damage.
Do not attempt to disassemble, modify or service the product or motor; no serviceable parts are
inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture. Contact your
La-Z-Boy dealer for service.
To reduce the risk of burns, fire, electric shock, serious
injury or death:
This product is intended for indoor residential use only.
The back of the unit must be lifted for assembly. Please seek assistance if you are unable to lift
at least 45 pounds without strain.
Keep upholstery away from flames or lit cigarettes. Upholstery may burn rapidly, with toxic gas and
thick smoke. Fires that begin elsewhere in a home may spread and involve upholstery. For your
safety, always use a properly installed smoke detector with working batteries.
Unplug the power cord immediately if you detect strange odors or fumes coming from the unit.
Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.
Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power
plug and pull it out.
Disconnect the power plug from outlet before cleaning, moving, servicing or when not in use for
an extended period of time.
Closely supervise children and disabled persons using this product.
This product has many moving parts, serious injury can occur if not used properly. Keep hands,
fingers and body parts away from the mechanism. To reduce the risk of head entrapment and
other injuries, keep children and pets away from openings and moving parts in and around furniture,
including the open area between a reclined back and an upright back on a reclining sofa.
Do not place power supply underneath the power motion furniture.
Do not place cord under carpet or in a location where it could become worn.
Do not allow electrical cord to be pinched anywhere.
Keep the electrical cord away from heat sources.
Do not use this product where the cord may be a trip hazard.
Provide a clear path for operation of the back and legrest. Place tables and area rugs at a distance
to allow the legrest to fully extend without rubbing or interference.
Do not use this product if it is damaged. Do not use attachments or substitute parts.
Never operate the unit with a damaged power supply, electrical cord, plug or connector. Check the
condition of the power supplies, electrical cords, plugs and connectors often.
DANGER
WARNING
Important Safety Instructions:
Important: Read these instructions thoroughly before using.
When assembling, do not plug in until directed in Operating Instructions.
Save These Instructions Save These Instructions
Important Safety Instructions:
Important: Read these instructions thoroughly before using.
When assembling, do not plug in until directed in Operating Instructions.
To reduce the risk of burns, fire, electric shock, serious
injury or death:
Do not operate the unit until the back is installed and locked.
Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back of the unit.
Only the occupant should operate the unit. Never attempt to open the legrest by pulling on it.
This unit is equipped with memory and home positions. Do not enter or exit the unit when the unit
is in motion.
To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
Do not stand, sit or place extra weight on the arms, back or open legrest.
This product may adversely affect medical devices. Do not use near people using or wearing
medical devices. Models with a wireless remote contain magnets in the cradle, which may
adversely affect medical devices.
Users of medical devices should contact their health care provider before using this product. Do
not use this product if you have poor circulation, are immobile, or cannot sense heat, except as
directed by your health care provider.
Do not use this product where aerosol (spray) products are being used or where oxygen is
being administered.
This product is not intended to be used as a bed. Do not sleep in for an extended period.
Double-insulated products are marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”
and may include the symbol (square within a square). Do not attempt to ground these products,
which use two systems of insulation instead of grounding. Double-insulated products should be
serviced only by qualified service personnel, using replacement parts identical to the original parts.
Before moving the product, disconnect the electrical plug from the wall outlet and secure the
mechanism to prevent unexpected opening or movement. Never move the product by the mechanism,
legrest, handle, reclining back, or swivel base.
Power Motion Furniture with and without Headrest and Lumbar units are intended for a single
occupant not exceeding 300 pounds per seat. Do not operate an individual seat with more than
one occupant in or on any part of the individual seat.
If you give this product to someone else, include this Operating Instructions manual.
M3
To reduce the risk of product damage:
To prevent damage to the power supply, do not plug in until instructed.
Never operate the unit except when it is on its base in the upright position.
Gently press the buttons during operation and avoid hitting the buttons with pointed or hard objects.
After 1 minute of continuous operation, allow the system to rest for 9 minutes.
Only operate when no foreign object or obstacle will impede, interfere, or otherwise damage
the unit in any of its positions or while in motion.
NOTICE
WARNING
Regulatory Compliance Statements for
Furniture with Wireless Remote
7
6
(Page intentionally left blank)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
This device complies with Industry Canada’s license-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain must be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Back Bracket
Body
Bracket
9
8
Body
Bracket
FIGURE 1FIGURE 2
FIGURE 4
FIGURE 5FIGURE 6
Electrical
Components Bag
120 Volt Power Cord
3. Install the back.
Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall
between the rear seat and tailgate, and align the brackets on the back with the brackets on the
body (FIGURE 2)
Lower the back onto the body, making sure the back and body brackets are completely engaged.
-To make sure the back is properly installed with both sets of back and body brackets
engaged, stand behind the chair and twist the back from side to side. If one or both sides
move out of position the brackets are not engaged (FIGURE 5). Remove the back and repeat
the steps above.
-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.
Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).
4. Remove the power supply from its packaging from the electrical components bag. Remove the power
supply and 120 volt power cord from the package.
5. Locate the motor connector behind the unit. Connect the motor connector to the power supply
connector. Align the connectors, push together until fully seated and close the locking cover to
secure the connection (FIGURE 6).
6. Connect the 120 volt power cord to the power supply (FIGURE 6). Do not plug in until instructed in
the operating instructions.
7. Proceed to the Battery Backup Assembly Instructions.
8. To remove the back, unplug the 120 volt power cord from the electrical outlet and disconnect the
power supply from the motor connector behind the unit. Reverse the Assembly Instructions steps.
When lifting the back up from the body, to lay across the arms, make sure to do so slowly and carefully
to prevent damage to the electrical connections.
Back and body brackets on this
side are not engaged. Remove
the back and reinstall.
Make this
connection
Power Supply*
Adjustable Headrest
Connection Brown
Motor Connector
Make this
connection
Tailgate Rear Seat
To reduce the risk of injury:
Do not operate the unit until the back is installed and locked.
The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
WARNING
NOTICE: -- To reduce the risk of product damage:
Do not plug in until instructed.
1. Once the furniture is unpacked, carefully remove the yellow electrical components bag from the body
bracket and set aside; depending on the product purchased, inside the bag are the power supply,
power cord, optional remote and three AAA batteries for the optional remote (FIGURE 1).
2. Make back electrical connections.
Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
attached to the back (one on each side), to a 90° angle (FIGURES 2 AND 3).
Locate and identify the two electrical connections between the back and the body. The color of
the connectors varies by date of manufacture.
-The brown connectors on the right side (sitting) are for the adjustable headrest feature. One
connector routes from bottom of the back panel and the other between the rear seat and tailgate.
Carefully rotate the back until the headrest actuator cable is able to reach the connector.
Connect the adjustable headrest (FIGURE 4). Align the pins and sockets in the brown connectors,
push the connectors together and close the locking cover to secure the connection.
*Power supplies/connections
may vary by date of manufacture.
Back
Bracket
Locking
Lever
at a 90
Degree
Angle
Locked
Position
Power Recliner with Headrest
Assembly Instructions
Power Recliner with Headrest
Assembly Instructions
Power Rocking Recliner Style Featured
FIGURE 3
11
10
To reduce the risk of injury:
Do not operate the unit until the back is installed and locked.
The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
WARNING
NOTICE: -- To reduce the risk of product damage:
Do not plug in until instructed.
1. Once the furniture is unpacked, carefully remove the red electrical components bag from the body
bracket and set aside; depending on the product purchased, inside the bag are the power supply,
power cord, optional remotes and three AAA batteries for the optional remote (FIGURE 1).
2. Make back electrical connections.
Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
attached to the back (one on each side), to a 90° angle (FIGURES 2 AND 3).
Locate and identify the electrical connection between the back and the body. The color of the
connectors varies by date of manufacture.
-The brown connectors on the right side (sitting) are for the adjustable headrest feature. One
connector routes from bottom of the back panel and the other between the rear seat and tailgate.
- The orange connectors on the left side (sitting) are for the adjustable lumbar feature. One connector
routes from bottom of the back panel and the other between the rear seat and tailgate.
Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the connectors.
Connect the adjustable headrest (FIGURE 4). Align the pins and sockets in the brown connectors,
push the connectors together and close the locking cover to secure the connection.
Connect the adjustable lumbar (FIGURE 4). Align the pins and sockets in the orange connectors,
push the connectors together and close the locking cover to secure the connection.
Power Recliner with Headrest
and Lumbar Assembly Instructions
3. Install the back.
Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall
between the rear seat and tailgate, and align the brackets on the back with the brackets on the
body (FIGURE 2).
Lower the back onto the body, making sure the back and body brackets are completely engaged.
-To make sure the back is properly installed with both sets of back and body brackets
engaged, stand behind the chair and twist the back from side to side. If one or both sides
move out of position the brackets are not engaged (FIGURE 5). Remove the back and repeat
the steps above.
-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.
Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).
4. Remove the power supply from its packaging from the electrical components bag. Remove the power
supply and 120 volt power cord from the package.
5. Locate the motor connector behind the unit. Connect the motor connector to the power supply
connector. Align the connectors, push together until fully seated and close the locking cover to
secure the connection (FIGURE 6).
6. Connect the 120 volt power cord to the power supply (FIGURE 6). Do not plug in until instructed in
the operating instructions.
7. Proceed to the Battery Backup Assembly Instructions.
8. To remove the back, unplug the 120 volt power cord from the electrical outlet and disconnect the
power supply from the motor connector behind the unit. Reverse the Assembly Instructions steps.
When lifting the back up from the body, to lay across the arms, make sure to do so slowly and carefully
to prevent damage to the electrical connections.
Body
Bracket
FIGURE 1FIGURE 2
FIGURE 4
FIGURE 5
Electrical
Components Bag
Back and body brackets on this
side are not engaged. Remove
the back and reinstall.
Adjustable Headrest
Connection Brown
Tailgate Rear Seat
Back
Bracket
Locking
Lever
at a 90
Degree
Angle
Locked
Position
Power Recliner with Headrest
and Lumbar Assembly Instructions
Back Bracket
Body
Bracket
Adjustable Lumbar
Connection Orange
FIGURE 6
120 Volt Power Cord
Make this
connection
Power Supply*
Motor Connector
Make this
connection
*Power supplies/connections
may vary by date of manufacture.
FIGURE 3
FIGURE 1
FIGURE 4
FIGURE 5
3. Install the back.
Continue rotating the back at a slight angle, making sure the headrest connection falls between the
rear seat and tailgate, and align the brackets on the back with the brackets on the body (FIGURE 2).
Lower the back onto the body, making sure the back and body brackets are completely engaged.
-To make sure the back is properly installed with both sets of back and body brackets
engaged, stand behind the chair and twist the back from side to side. If one or both sides
move out of position the brackets are not engaged (FIGURE 5). Remove the back and repeat
the steps above.
-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.
Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).
Back and body brackets on this
side are not engaged. Remove
the back and reinstall.
Adjustable Headrest
Connection Brown
To reduce the risk of injury:
Do not operate the unit until the back is installed and locked.
The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
WARNING
NOTICE: -- To reduce the risk of product damage:
Do not plug in until instructed.
1. Once the furniture is unpacked, carefully remove the yellow electrical components bag from the body
bracket and set aside; depending on the product purchased, inside the bag are the power supply,
power cord, optional remote and three AAA batteries for the optional remote (FIGURE 1).
2. Make back electrical connections.
Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
attached to the back (one on each side), to a 90° angle (FIGURES 2 AND 3).
Locate and identify the electrical connections between the back and the body.
-The brown connectors on the right side (sitting) are for the adjustable headrest feature. One
connector routes from bottom of the back panel and the other between the rear seat and tailgate.
Carefully rotate the back until the headrest actuator cable is able to reach the connector.
Connect the adjustable headrest (FIGURE 4). Align the pins and sockets in the brown connectors,
push the connectors together and close the locking cover to secure the connection. Back
Bracket
Locking
Lever
at a 90
Degree
Angle
Locked
Position
Power Sofa with Headrest
Assembly Instructions
Power Sofa with Headrest
Assembly Instructions
Back Bracket
Body Bracket
FIGURE 2
13
12
Body
Bracket
Electrical
Components Bag
FIGURE 3
Tailgate Rear Seat
15
14
Power Sofa with Headrest
Assembly Instructions
Base Rail
Lock
Washer
Upper Jam Nut
Lower Jam Nut
Adjustable Glide
4. Adjust the glides to ensure a height that provides a clear path for operation of the legrest. Each glide is
attached to the base rail by one jam nut and one lock washer on top of the base rail, and one jam nut
on the bottom of the base rail.
To extend the glide, loosen the upper jam nut by rotating clockwise. Turn the lower jam nut
clockwise to the desired height.
Tighten the upper jam nut by rotating counterclockwise.
Repeat steps one and two for each adjustable glide on the unit, if needed.
Repeat this procedure, as necessary, to adjust the front height of the unit and level it.
5. Locate the motor connector, one behind each reclining seat (FIGURE 6). Connect the Y-cable to the
motor connectors and to the power supply.
Align one motor connector to a long lead Y-cable connector, push the connectors together until
seated and close the locking cover to secure the connection (FIGURE 7). Repeat this for the other
motor connector and Y-cable long lead. Then align the short lead of the Y-cable to the power supply
connector, push the connectors together until seated and close the locking cover to secure the
connection (FIGURE 8).
6. Connect the 120 volt power cord to the power supply (FIGURE 9). Align the connector ends and
push together until seated. Do this for each power supply and 120 volt power cord included with the
furniture. Do not plug in until instructed in the Operating Instructions.
7. Proceed to the Battery Backup Assembly Instructions.
To Remove a Back:
1. Unplug the 120 volt power cord and disconnect the power supply from the Y-cable. Reverse the
Assembly Instructions steps. When lifting the back up from the body, to lay across the arms,
make sure to do so slowly and carefully to prevent damage to the electrical connections.
2. Repeat step 1 for the other side of the back.
FIGURE 6FIGURE 7
Motor Connector
FIGURE 8FIGURE 9
Y-Cable Long Leads
Make this
connection
Power Supply
Y-Cable Short Lead
Make these
connections
Make this
connection
Power Supply 120 Volt Power Cord
Power Sofa with Headrest
Assembly Instructions
17
16
Body
Bracket
FIGURE 1
FIGURE 4
FIGURE 5
Electrical
Components Bag
3. Install the back.
Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall
between the rear seat and tailgate, and align the brackets on the back with the brackets on the
body (FIGURE 2).
Lower the back onto the body, making sure the back and body brackets are completely engaged.
-To make sure the back is properly installed with both sets of back and body brackets
engaged, stand behind the chair and twist the back from side to side. If one or both sides
move out of position the brackets are not engaged (FIGURE 5). Remove the back and repeat
the steps above.
-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.
Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).
Back and body brackets on this
side are not engaged. Remove
the back and reinstall.
Adjustable Headrest
Connection Brown
To reduce the risk of injury:
Do not operate the unit until the back is installed and locked.
The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
WARNING
NOTICE: -- To reduce the risk of product damage:
Do not plug in until instructed.
1. Once the furniture is unpacked, carefully remove the red electrical components bag from the body
bracket and set aside; depending on the product purchased, inside the bag are the power supply,
power cord, optional remote and three AAA batteries for the optional remote (FIGURE 1).
2. Make back electrical connections.
Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
attached to the back (one on each side), to a 90° angle (FIGURES 2 AND 3).
Locate and identify the orange and brown electrical connections between the back and the body.
-The brown connectors on the right side (sitting) are for the adjustable headrest feature. One
connector routes from bottom of the back panel and the other between the rear seat and tailgate.
-The orange connectors on the left side (sitting) are for the adjustable lumbar feature.
One connector routes from bottom of the back panel and the other between the rear seat and tailgate.
Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the connectors.
Connect the adjustable headrest (FIGURE 4). Align the pins and sockets in the brown connectors,
push the connectors together and close the locking cover to secure the connection.
Connect the adjustable lumbar (FIGURE 4). Align the pins and sockets in the orange connectors,
push the connectors together and close the locking cover to secure the connection.
Back
Bracket
Locking
Lever
at a 90
Degree
Angle
Locked
Position
Power Sofa with Headrest
and Lumbar Assembly Instructions
Power Sofa with Headrest
and Lumbar Assembly Instructions
Back Bracket
Body Bracket
FIGURE 2
FIGURE 3
Tailgate Rear Seat
Adjustable Lumbar
Connection Orange
19
18
Power Sofa with Headrest
and Lumbar Assembly Instructions
Base Rail
Lock
Washer
Upper Jam Nut
Lower Jam Nut
Adjustable Glide
4. Adjust the glides to ensure a height that provides a clear path for operation of the legrest. Each glide is
attached to the base rail by one jam nut and one lock washer on top of the base rail, and one jam nut
on the bottom of the base rail.
To extend the glide, loosen the upper jam nut by rotating clockwise. Turn the lower jam nut
clockwise to the desired height.
Tighten the upper jam nut by rotating counterclockwise.
Repeat steps one and two for each adjustable glide on the unit, if needed.
Repeat this procedure, as necessary, to adjust the front height of the unit and level it.
5. Locate the motor connector, one behind each reclining seat (FIGURE 6). Connect the Y-cable to the
motor connectors and to the power supply.
Align one motor connector to a long lead Y-cable connector, push the connectors together until
seated and close the locking cover to secure the connection (FIGURE 7). Repeat this for the other
motor connector and Y-cable long lead. Then align the short lead of the Y-cable to the power supply
connector, push the connectors together until seated and close the locking cover to secure the
connection (FIGURE 8).
6. Connect the 120 volt power cord to the power supply (FIGURE 9). Do not plug in until instructed in
the Operating Instructions.
7. Proceed to the Battery Backup Assembly Instructions.
To Remove a Back:
1. Unplug the 120 volt power cord and disconnect the power supply from the Y-cable. Reverse the
Assembly Instructions steps. When lifting the back up from the body, to lay across the arms,
make sure to do so slowly and carefully to prevent damage to the electrical connections.
2. Repeat step 1 for the other side of the back.
FIGURE 6FIGURE 7
FIGURE 8FIGURE 9
Y-Cable Long Leads
Make this
connection
Power Supply
Y-Cable Short Lead
Make these
connections
Make this
connection
Power Supply 120 Volt Power Cord
Power Sofa with Headrest
and Lumbar Assembly Instructions
Motor Connector
21
20
Battery Backup
Assembly Instructions
NOTICE: Replace the power supply batteries every six months
and after each power failure use.
The performance of the built-in battery backup cannot be guaranteed. The backup system is
designed to return a reclined unit to the upright, closed position for exiting ease during a power
interruption. It is not intended to recline the unit. If you require continuing use during a power outage,
then you should purchase a separate battery backup system. Contact your La-Z-Boy®dealer for
more information.
When operating on battery backup the furniture operating speed is reduced. In addition, the
Memory I and Memory II programs and the USB charging port are disabled.
Always maintain constant, even pressure on the button when operating on battery backup to
reduce the energy consumption.
Replace the batteries every six months and after each power failure use.
The battery backup is located in the power supply and uses two 9-volt alkaline batteries (not included).
1. Unplug the 120 volt power cord from the electrical outlet, and disconnect the power supply
from the motor connector.
2. The battery compartment is located in the bottom of the power supply. Slide the battery cover
up to access the battery compartment.
3. Snap the connection caps on the battery terminals. Place the batteries in the power supply.
4. Slide the battery cover over the batteries.
5. Proceed to Operating Instructions.
Power
Supply
(2) 9-Volt
Alkaline Batteries
Power Supply Specifications:
Input: 100V-240V~, AC 50/60 Hz 1.5A
Output: 29V DC 2.5A
Battery
Cover
(Page intentionally left blank)
Operating Instructions for Power Recliner with
Headrest with Standard Control Panel
Right Side Sitting Featured; Left Side Sitting Opposite This View
23
22
Back toggle
Press the Back toggle rearward and hold to recline
the back. Or press it forward and hold to return
the back to the upright position. Release the button
to stop the back in any reclined position, or when
fully reclined or fully raised.
Headrest toggle
Press the Headrest toggle forward and hold to
rotate the headrest forward. Or press it rearward
and hold to return the headrest. Release the
button to stop the headrest in any position, or
when fully extended or fully retracted.
USB port
Rearward Forward
Home button
Press and release the
Home button to return
the furniture to the
upright, closed,
stored position.
Legrest toggle
Press the Legrest toggle rearward and hold
to extend the legrest and tilt the chair body
backward. Or press it forward and hold to close
the legrest and return the chair body. Release
the button to stop the legrest in any extended
position, or when fully raised or fully closed.
Memory I button
Memory II button
Press and release a
Memory button to
automatically move
the furniture to the
stored setting.
(pressing and holding
stores the setting)
To reduce the risk of burns, electric shock,
serious injury or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
USB Output Specifications:
5 VDC, 1.0A
To reduce the risk of electric shock, serious injury
or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.
Do not use the unit if the button activation switch has been exposed to water or any liquid.
Do not handle the plug or remote control with wet hands.
Do not attempt to disassemble, modify or service the product or motor; no serviceable
parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.
Contact your La-Z-Boy dealer for service.
DANGER
To reduce the risk of electric shock or serious injury:
Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.
Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that
no children or pets are in close proximity.
The Power Rocking Recliner and Power Wall Recliner with Headrest units are intended for
a single occupant not exceeding 300 pounds per seat. Do not operate an individual seat
with more than one occupant in or on any part of the individual seat.
To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
WARNING
Operating Instructions for Power Recliner with
Headrest with Standard Control Panel
After 1 minute of continuous operation, allow the system to rest for 9 minutes.
NOTICE:
Only proceed after having followed the Assembly Instructions completely.
Operating Instructions for Furniture with a Control Panel:
Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running
from the chair to the outlet to allow for rocking and reclining. Never stretch or strain a cord.
The power features are operated by the toggles on the Control Panel located on the outside
arm. Each feature has a dedicated toggle for independent operation of the feature, or
simultaneous operation of multiple features when more than one toggle is pressed.*
Press rearward the Back and Legrest toggle to increase the amount of recline or extension. Press
the toggle forward to retract the back and legrest.
Press the Headrest toggle forward to increase the amount of adjustment. Press the toggle rearward
to decrease the amount of adjustment.
The Control Panel also features Memory I, Memory II and Home buttons for personal, effortless
operation and added comfort. Two preferred recline settings may be stored for a more enjoyable
reclining experience. Press and release a stored Memory button (not holding for more than 2
seconds) and the furniture automatically moves to the stored setting. If no setting is stored, the
furniture will move to its home, or upright, closed and stored position. Press and release the Home
button and the furniture automatically moves to its home position.
A handy USB port for charging small personal electronic devices is located in the Control Panel to
keep your devices close at hand and ready for use at all times.
Unplug the power supply from the wall outlet if you are going to be away from your residence for
an extended period of time.
* When the furniture is powered by the 9-volt battery backup or the optional rechargeable lithium-ion
battery pack, only two features can be operated at the same time.
25
24
Operating Instructions for Power Recliner
with Headrest with Standard Control Panel
To Program and Use the Memory I or Memory II:
1. Adjust the furniture to the best and most comfortable position for you using the toggle buttons.
2. Press and hold the Memory I or Memory II button for three (or more) seconds.
3. Listen for the beepto indicate the setting was saved in memory.
Memory I setting plays a single beep to indicate a successful save.
Memory II setting plays a double beep to indicate a successful save.
Three quick beeps play when the setting did not successfully save.
4. The next time you use your furniture, press and release either the Memory I or Memory II button
(not holding longer than two seconds) and the furniture automatically moves to the saved setting.
If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.
Pressing a toggle or button on the control panel will stop the automatic motion of the furniture.
The furniture does not restart once the toggle or button is released. Another press of the Memory I
or Memory II button is required to start the furniture in motion again.
NOTE: All features start in motion upon a Memory button press if the feature is programmed to
recline or extend, except for the headrest.* When the headrest is programmed to extend, the headrest
does not start in motion until the back reaches approximately 40% recline, or its programmed recline
setting if set to less than 40% recline. This is done to guard against an undesirable positioning of the
head and neck when moving into the stored recline setting.
* Furniture must be plugged into a power outlet or powered by the optional rechargeable lithium-ion
battery pack for the Memory feature to function. This feature is disabled when powered by the 9-volt
battery backup. Additionally, when powered by the optional rechargeable lithium-ion battery pack,
only two features operate at the same time.
To Use the Home Button:
The Home button returns the back to its fully upright position and the legrest, headrest and lumbar
to the fully retracted and closed position.
Press and release the Home button. The furniture automatically starts in motion, moving the back,
legrest, headrest and lumbar back to the upright and retracted positions under full, normal power.
All motion stops if any toggle or button is pressed while the furniture is moving to home. The motion
does not resume when the toggle or button is released. Another press and release of the Home
button is required to restart the automatic home program.
NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to
the home position first. Once the back and legrest are fully upright and retracted, then the headrest
will begin to move to the retracted, home position. When powered by the optional rechargeable lithium-
ion battery pack, the headrest will return to the Home position first, and then the back and legrest
return to Home.
To Use the USB Charging Port:
Plug the USB cable of a small portable electronic device into the USB charging port. Unplug the USB
cable from the charging port when charging is complete. The USB port is for charging only and does
not save or transfer data.
NOTE: When the furniture is operating on the 9-volt battery back-up in the power supply, the USB
charge port is disabled. When the furniture is powered by the optional rechargeable lithium-ion
battery pack, the USB port is enabled, as long as there is adequate charge.
(Page intentionally left blank)
27
26
Operating Instructions for Power Recliner with
Headrest and Lumbar with Standard Control Panel
Right Side Sitting Featured; Left Side Sitting Opposite This View
Headrest toggle
Press the Headrest toggle forward and hold to rotate
the headrest forward. Or press it rearward and hold
to return the headrest. Release the button to stop
the headrest in any position, or when fully extended
or fully retracted.
Back toggle
Press the Back toggle rearward and hold to recline
the chair back. Or press it forward and hold to return
the back to the upright position. Release the button
to stop the back in any reclined position, or when
fully reclined or fully raised.
USB port
To reduce the risk of burns, electric shock,
serious injury or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
To reduce the risk of electric shock, serious injury
or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.
Do not use the unit if the button activation switch has been exposed to water or any liquid.
Do not handle the plug or remote control with wet hands.
Do not attempt to disassemble, modify or service the product or motor; no serviceable
parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.
Contact your La-Z-Boy dealer for service.
DANGER
To reduce the risk of electric shock or serious injury:
Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.
Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that no
children or pets are in close proximity.
The Power Rocking Recliner and Power Wall Recliner with Headrest and Lumbar units are
intended for a single occupant not exceeding 300 pounds per seat. Do not operate an
individual seat with more than one occupant in or on any part of the individual seat.
To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
WARNING
Operating Instructions for Power Recliner with
Headrest and Lumbar with Standard Control Panel
After 1 minute of continuous operation, allow the system to rest for 9 minutes.
NOTICE:
Only proceed after having followed the Assembly Instructions completely.
Operating Instructions for Furniture with a Control Panel:
Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running
from the chair to the outlet to allow for reclining. Never stretch or strain a cord.
The power features are operated by the toggles on the Control Panel located on the outside
arm. Each feature has a dedicated toggle for independent operation of the feature, or
simultaneous operation of multiple features when more than one toggle is pressed. *
Press rearward the Back and Legrest toggle to increase the amount of recline or extension.
Press the toggle forward to retract the back and legrest.
Press the Headrest and Lumbar toggle forward to increase the amount of adjustment. Press the toggle
rearward to decrease the amount of adjustment.
The Control Panel also features Memory I, Memory II and Home buttons for personal, effortless operation
and added comfort. Two preferred recline settings may be stored for a more enjoyable reclining experience.
Press and release a stored Memory button (not holding for more than 2 seconds) and the furniture
automatically moves to the stored setting. If no setting is stored, the furniture will move to its home, or
upright, closed and stored position. Press and release the Home button and the furniture automatically
moves to its home position.
A handy USB port for charging small personal electronic devices is located in the cradle to keep
your devices close at hand and ready for use at all times.
Unplug the power supply from the wall outlet if you are going to be away from your residence for
an extended period of time.
* When the furniture is powered by the 9-volt battery backup or the optional rechargeable
lithium-ion pack, only two features can be operated at the same time.
Legrest toggle
Press the Legrest toggle rearward and hold to
extend the legrest and tilt the chair body backward.
Or press it forward and hold to close the legrest
and return the chair body. Release the button to
stop the legrest in any extended position, or when
fully raised or fully closed.
Rearward
USB Output Specifications:
5 VDC, 1.0A
Forward
Home button
Press and release the
Home button to return
the furniture to the
upright, closed,
stored position.
Memory I button
Memory II button
Press and release a
Memory button to
automatically move
the furniture to the
stored setting.
(pressing and holding
stores the setting)
Lumbar toggle
Press the Lumbar toggle forward and hold to
increase the lumbar intensity. Or press it rearward
and hold to decrease lumbar intensity. Release the
button to stop the lumbar in any position, or when
fully extended or fully retracted.
29
28
Operating Instructions for Power Recliner with
Headrest and Lumbar with Standard Control Panel
To Program and Use the Memory I or Memory II:
1. Adjust the furniture to the best and most comfortable position for you using the toggle buttons.
2. Press and hold the Memory I or Memory II button for three (or more) seconds.
3. Listen for the beepto indicate the setting was saved in memory.
Memory I setting plays a single beep to indicate a successful save.
Memory II setting plays a double beep to indicate a successful save.
Three quick beeps play when the setting did not successfully save.
4. The next time you use your furniture, press and release either the Memory I or Memory II button
(not holding longer than two seconds) and the furniture automatically moves to the saved setting.
If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.
Pressing a toggle or button on the control panel will stop the automatic motion of the furniture.
The furniture does not restart once the toggle or button is released. Another press of the Memory I
or Memory II button is required to start the furniture in motion again.
NOTE: All features start in motion upon a Memory button press if the feature is programmed to
recline or extend, except for the headrest.* When the headrest is programmed to extend, the headrest
does not start in motion until the back reaches approximately 40% recline, or its programmed recline
setting if set to less than 40% recline. This is done to guard against an undesirable positioning of the
head and neck when moving into the stored recline setting.
* Furniture must be plugged into a power outlet or powered by the optional rechargeable lithium-ion
battery pack for the Memory feature to function. This feature is disabled when powered by the 9-volt
battery backup. Additionally, when powered by the optional rechargeable lithium-ion battery pack,
only two features operate at the same time.
To Use the Home Button:
The Home button returns the back to its fully upright position and the legrest, headrest and lumbar
to the fully retracted and closed position.
Press and release the Home button. The furniture automatically starts in motion, moving the back,
legrest, headrest and lumbar back to the upright and retracted positions under full, normal power.
All motion stops if any toggle or button is pressed while the furniture is moving to home. The motion
does not resume when the toggle or button is released. Another press and release of the Home
button is required to restart the automatic home program.
NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to
the home position first. Once the back and legrest are fully upright and retracted, then the headrest
and lumbar begin to move to the retracted, home position. When powered by the optional rechargeable
lithium-ion battery pack, the headrest and lumbar return to the Home position first, and then the
back and legrest return to Home.
To Use the USB Charging Port:
Plug the USB cable of a small portable electronic device into the USB charging port. Unplug the USB
cable from the charging port when charging is complete. The USB port is for charging only and does
not save or transfer data.
NOTE: When the furniture is operating on the 9-volt battery back-up in the power supply, the USB
charge port is disabled. When the furniture is powered by the optional rechargeable lithium-ion
battery pack, the USB port is enabled, as long as there is adequate charge.
(Page intentionally left blank)
31
30
Operating Instructions for Power Sofa with
Headrest with Standard Control Panel
Right Side Sitting Featured; Left Side Sitting Opposite This View
Back toggle
Press the Back toggle rearward and hold to recline
the back. Or press it forward and hold to return
the back to the upright position. Release the button
to stop the back in any reclined position, or when
fully reclined or fully raised.
Headrest toggle
Press the Headrest toggle forward and hold to
rotate the headrest forward. Or press it rearward
and hold to return the headrest. Release the
button to stop the headrest in any position, or
when fully extended or fully retracted.
USB port
Rearward Forward
Home button
Press and release the
Home button to return
the furniture to the
upright, closed,
stored position.
Legrest toggle
Press the Legrest toggle rearward and hold
to extend the legrest and tilt the chair body
backward. Or press it forward and hold to close
the legrest and return the chair body. Release
the button to stop the legrest in any extended
position, or when fully raised or fully closed.
Memory I button
Memory II button
Press and release a
Memory button to
automatically move
the furniture to the
stored setting.
(pressing and holding
stores the setting)
To reduce the risk of burns, electric shock,
serious injury or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
USB Output Specifications:
5 VDC, 1.0A
To reduce the risk of electric shock, serious injury
or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.
Do not use the unit if the button activation switch has been exposed to water or any liquid.
Do not handle the plug or remote control with wet hands.
Do not attempt to disassemble, modify or service the product or motor; no serviceable
parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.
Contact your La-Z-Boy dealer for service.
DANGER
To reduce the risk of electric shock or serious injury:
Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.
Power Motion Furniture with Headrest units are intended for a single occupant not
exceeding 300 pounds per seat. Do not operate an individual seat with more than one
occupant in or on any part of the individual seat.
To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
WARNING
Operating Instructions for Power Sofa with
Headrest with Standard Control Panel
After 1 minute of continuous operation, allow the system to rest for 9 minutes.
NOTICE:
Only proceed after having followed the Assembly Instructions completely.
Operating Instructions for Furniture with a Control Panel:
Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running
from the chair to the outlet to allow for rocking and reclining. Never stretch or strain a cord.
The power features are operated by the toggles on the Control Panel located on the outside
arm. Each feature has a dedicated toggle for independent operation of the feature, or
simultaneous operation of multiple features when more than one toggle is pressed. *
Press rearward the Back and Legrest toggle to increase the amount of recline or extension. Press
the toggle forward to retract the back and legrest.
Press the Headrest toggle forward to increase the amount of adjustment. Press the toggle rearward
to decrease the amount of adjustment.
The Control Panel also features Memory I, Memory II and Home buttons for personal, effortless
operation and added comfort. Two preferred recline settings may be stored for a more enjoyable
reclining experience. Press and release a stored Memory button (not holding for more than 2
seconds) and the furniture automatically moves to the stored setting. If no setting is stored, the
furniture will move to its home, or upright, closed and stored position. Press and release the Home
button and the furniture automatically moves to its home position.
A handy USB port for charging small personal electronic devices is located in the Control Panel to
keep your devices close at hand and ready for use at all times.
Unplug the power supply from the wall outlet if you are going to be away from your residence for
an extended period of time.
* When the furniture is powered by the 9-volt battery backup or the optional rechargeable lithium-ion
battery pack, only two features can be operated at the same time.
Operating Instructions for Power Sofa with
Headrest with Standard Control Panel
To Program and Use the Memory I or Memory II:
1. Adjust the furniture to the best and most comfortable position for you using the toggle buttons.
2. Press and hold the Memory I or Memory II button for three (or more) seconds.
3. Listen for the beepto indicate the setting was saved in memory.
Memory I setting plays a single beep to indicate a successful save.
Memory II setting plays a double beep to indicate a successful save.
Three quick beeps play when the setting did not successfully save.
4. The next time you use your furniture, press and release either the Memory I or Memory II button
(not holding longer than two seconds) and the furniture automatically moves to the saved setting.
If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.
Pressing a toggle or button on the control panel will stop the automatic motion of the furniture.
The furniture does not restart once the toggle or button is released. Another press of the Memory I
or Memory II button is required to start the furniture in motion again.
NOTE: All features start in motion upon a Memory button press if the feature is programmed to
recline or extend, except for the headrest.* When the headrest is programmed to extend, the headrest
does not start in motion until the back reaches approximately 40% recline, or its programmed recline
setting if set to less than 40% recline. This is done to guard against an undesirable positioning of the
head and neck when moving into the stored recline setting.
* Furniture must be plugged into a power outlet or powered by the optional rechargeable lithium-ion
battery pack for the Memory feature to function. This feature is disabled when powered by the 9-volt
battery backup. Additionally, when powered by the optional rechargeable lithium-ion battery pack,
only two features operate at the same time.
To Use the Home Button:
The Home button returns the back to its fully upright position and the legrest, headrest and lumbar
to the fully retracted and closed position.
Press and release the Home button. The furniture automatically starts in motion, moving the back,
legrest, headrest and lumbar back to the upright and retracted positions under full, normal power.
All motion stops if any toggle or button is pressed while the furniture is moving to home. The motion
does not resume when the toggle or button is released. Another press and release of the Home
button is required to restart the automatic home program.
NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to
the home position first. Once the back and legrest are fully upright and retracted, then the headrest
will begin to move to the retracted, home position. When powered by the optional rechargeable lithium-
ion battery pack, the headrest will return to the Home position first, and then the back and legrest
return to Home.
To Use the USB Charging Port:
Plug the USB cable of a small portable electronic device into the USB charging port. Unplug the USB
cable from the charging port when charging is complete. The USB port is for charging only and does
not save or transfer data.
NOTE: When the furniture is operating on the 9-volt battery back-up in the power supply, the USB
charge port is disabled. When the furniture is powered by the optional rechargeable lithium-ion
battery pack, the USB port is enabled, as long as there is adequate charge.
33
32
(Page intentionally left blank)
35
34
To reduce the risk of electric shock, serious injury
or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.
Do not use the unit if the button activation switch has been exposed to water or any liquid.
Do not handle the plug or remote control with wet hands.
Do not attempt to disassemble, modify or service the product or motor; no serviceable
parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.
Contact your La-Z-Boy dealer for service.
DANGER
To reduce the risk of electric shock or serious injury:
Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.
Power Motion Furniture with Headrest and Lumbar units are intended for a single occupant
not exceeding 300 pounds per seat. Do not operate an individual seat with more than one
occupant in or on any part of the individual seat.
To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
WARNING
Operating Instructions for Power Sofa with Headrest
and Lumbar with Standard Control Panel
After 1 minute of continuous operation, allow the system to rest for 9 minutes.
NOTICE:
Only proceed after having followed the Assembly Instructions completely.
Operating Instructions for Furniture with a Control Panel:
Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running
from the chair to the outlet to allow for reclining. Never stretch or strain a cord.
The power features are operated by the toggles on the Control Panel located on the outside
arm. Each feature has a dedicated toggle for independent operation of the feature, or
simultaneous operation of multiple features when more than one toggle is pressed. *
Press rearward the Back and Legrest toggle to increase the amount of recline or extension.
Press the toggle forward to retract the back and legrest.
Press the Headrest and Lumbar toggle forward to increase the amount of adjustment. Press the toggle
rearward to decrease the amount of adjustment. Press the toggle rearward to decrease the amount of
adjustment.
The Control Panel also features Memory I, Memory II and Home buttons for personal, effortless operation
and added comfort. Two preferred recline settings may be stored for a more enjoyable reclining experience.
Press and release a stored Memory button (not holding for more than 2 seconds) and the furniture
automatically moves to the stored setting. If no setting is stored, the furniture will move to its home, or
upright, closed and stored position. Press and release the Home button and the furniture automatically
moves to its home position.
A handy USB port for charging small personal electronic devices is located in the cradle to keep
your devices close at hand and ready for use at all times.
Unplug the power supply from the wall outlet if you are going to be away from your residence for
an extended period of time.
* When the furniture is powered by the 9-volt battery backup or the optional rechargeable
lithium-ion pack, only two features can be operated at the same time.
Operating Instructions for Power Sofa with Headrest
and Lumbar with Standard Control Panel
Right Side Sitting Featured; Left Side Sitting Opposite This View
Headrest toggle
Press the Headrest toggle forward and hold to rotate
the headrest forward. Or press it rearward and hold
to return the headrest. Release the button to stop
the headrest in any position, or when fully extended
or fully retracted.
Back toggle
Press the Back toggle rearward and hold to recline
the chair back. Or press it forward and hold to return
the back to the upright position. Release the button
to stop the back in any reclined position, or when
fully reclined or fully raised.
USB port
To reduce the risk of burns, electric shock,
serious injury or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
Legrest toggle
Press the Legrest toggle rearward and hold to
extend the legrest and tilt the chair body backward.
Or press it forward and hold to close the legrest
and return the chair body. Release the button to
stop the legrest in any extended position, or when
fully raised or fully closed.
Rearward
USB Output Specifications:
5 VDC, 1.0A
Forward
Home button
Press and release the
Home button to return
the furniture to the
upright, closed,
stored position.
Memory I button
Memory II button
Press and release a
Memory button to
automatically move
the furniture to the
stored setting.
(pressing and holding
stores the setting)
Lumbar toggle
Press the Lumbar toggle forward and hold to
increase the lumbar intensity. Or press it rearward
and hold to decrease lumbar intensity. Release the
button to stop the lumbar in any position, or when
fully extended or fully retracted.
37
36
Operating Instructions for Power Sofa with Headrest
and Lumbar with Standard Control Panel
To Program and Use the Memory I or Memory II:
1. Adjust the furniture to the best and most comfortable position for you using the toggle buttons.
2. Press and hold the Memory I or Memory II button for three (or more) seconds.
3. Listen for the beepto indicate the setting was saved in memory.
Memory I setting plays a single beep to indicate a successful save.
Memory II setting plays a double beep to indicate a successful save.
Three quick beeps play when the setting did not successfully save.
4. The next time you use your furniture, press and release either the Memory I or Memory II button
(not holding longer than two seconds) and the furniture automatically moves to the saved setting.
If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.
Pressing a toggle or button on the control panel will stop the automatic motion of the furniture.
The furniture does not restart once the toggle or button is released. Another press of the Memory I
or Memory II button is required to start the furniture in motion again.
NOTE: All features start in motion upon a Memory button press if the feature is programmed to
recline or extend, except for the headrest.* When the headrest is programmed to extend, the headrest
does not start in motion until the back reaches approximately 40% recline, or its programmed recline
setting if set to less than 40% recline. This is done to guard against an undesirable positioning of the
head and neck when moving into the stored recline setting.
* Furniture must be plugged into a power outlet or powered by the optional rechargeable lithium-ion
battery pack for the Memory feature to function. This feature is disabled when powered by the 9-volt
battery backup. Additionally, when powered by the optional rechargeable lithium-ion battery pack,
only two features operate at the same time.
To Use the Home Button:
The Home button returns the back to its fully upright position and the legrest, headrest and lumbar
to the fully retracted and closed position.
Press and release the Home button. The furniture automatically starts in motion, moving the back,
legrest, headrest and lumbar back to the upright and retracted positions under full, normal power.
All motion stops if any toggle or button is pressed while the furniture is moving to home. The motion
does not resume when the toggle or button is released. Another press and release of the Home
button is required to restart the automatic home program.
NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to
the home position first. Once the back and legrest are fully upright and retracted, then the headrest
and lumbar begin to move to the retracted, home position. When powered by the optional rechargeable
lithium-ion battery pack, the headrest and lumbar return to the Home position first, and then the
back and legrest return to Home.
To Use the USB Charging Port:
Plug the USB cable of a small portable electronic device into the USB charging port. Unplug the USB
cable from the charging port when charging is complete. The USB port is for charging only and does
not save or transfer data.
NOTE: When the furniture is operating on the 9-volt battery back-up in the power supply, the USB
charge port is disabled. When the furniture is powered by the optional rechargeable lithium-ion
battery pack, the USB port is enabled, as long as there is adequate charge.
(Page intentionally left blank)
39
38
To reduce the risk of electric shock, serious injury
or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.
Do not use the unit if the button activation switch has been exposed to water or any liquid.
Do not handle the plug or remote control with wet hands.
Do not attempt to disassemble, modify or service the product or motor; no serviceable
parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.
Contact your La-Z-Boy dealer for service.
DANGER
To reduce the risk of electric shock or serious injury:
Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.
Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that no
children or pets are in close proximity.
The Power Rocking Recliner and Power Wall Recliner with Headrest units are intended for
a single occupant not exceeding 300 pounds per seat. Do not operate an individual seat
with more than one occupant in or on any part of the individual seat.
To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
WARNING
Operating Instructions for Power Recliner
with Headrest with Optional Wireless Remote
After 1 minute of continuous operation, allow the system to rest for 9 minutes.
NOTICE:
Only proceed after having followed the Assembly Instructions completely.
Operating Instructions for Furniture with Optional Wireless Remote:
Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running
from the chair to the outlet to allow for rocking and reclining. Never stretch or strain a cord.
The power features are operated by the buttons on the remote located in the
remote cradle on the outside arm, and by the buttons on the cradle itself. Each feature
has a dedicated button on the remote for independent operation of the feature, or
simultaneous operation of multiple features when more than one button is pressed. *
A press on the left side of a button (arrow UP) on the remote increases the
amount of recline or adjustment, while a press on the right side (arrow DOWN)
decreases the amount of recline or adjustment.
The Remote and Cradle both feature a Memory I, Memory II and Home button for personal, effortless
operation and added comfort. Two preferred recline settings may be stored for a more enjoyable reclining
experience at the mere press of a button. Press and release a stored Memory button (not holding for more
than 2 seconds) and the furniture automatically moves to the stored setting. Press and release the Home
button and the furniture automatically moves to its home, or upright, closed and stored position.
A handy USB port for charging small personal electronic devices is located in the cradle to keep
your devices close at hand and ready for use at all times.
Unplug the power supply from the wall outlet if you are going to be away from your residence for
an extended period of time.
* When the furniture is powered by the 9-volt battery backup or the optional rechargeable
lithium-ion pack, only two features can be operated at the same time.
Operating Instructions for Power Recliner
with Headrest with Optional Wireless Remote
Back button
Press the Back button arrow UP and hold
to recline the back. Or press the arrow
DOWN and hold to return the back to the
upright position. Release the button to
stop the back in any reclined position
or when fully reclined or fully raised.
Home button
Press and release the Home button to
automatically return the furniture to its
upright, closed and stored position.
Memory I and
Memory II buttons
Press and release the
Memory I or Memory II
button to automatically move
the furniture to a stored setting.
(pressing and holding
stores the setting)
Legrest button
Press the Legrest arrow UP
and hold to extend the
legrest and tilt the chair
body backward. Or press the
arrow DOWN and hold to
close the legrest and return
the chair body. Release the
button to stop the legrest in
any extended position or when
fully raised or fully closed.
Headrest button
Press the Headrest button
arrow UP and hold to rotate
the headrest forward. Or
press the arrow DOWN and
hold to return the headrest.
Release the button to stop
the headrest in any position
or when fully extended or
fully retracted.
To reduce the risk of burns, electric shock,
serious injury or death:
Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79

La-Z-Boy 10U502 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues