DREAME T30, T30 Cordless Vacuum Cleaner Manuel utilisateur

  • Bonjour ! Je suis votre assistant d'aide sur le Dreame, et j'ai lu le manuel de l'aspirateur sans fil VTT1. Je suis prêt à répondre à vos questions. Ce manuel couvre tous les aspects de l'appareil, de son installation à son entretien, en passant par ses fonctions comme les différents modes de nettoyage et accessoires. N'hésitez pas à me solliciter pour toute question.
  • Comment puis-je changer les niveaux d'aspiration ?
    Comment activer le mode nettoyage continu ?
    Comment puis-je nettoyer le filtre ?
Dreame
Cordless Vacuum Cleaner
User Manual
THANK YOU
FOR PURCHASING THIS DREAME
VACUUM CLEANER.
With it you are obtaining a high quality product that is engineered for
optimal performance. If you have any questions on the product, please
contact us: aftersales@dreame.tech.
Registration Quick Start
Welcome to register a Dreame account
by scanning the QR code.
You are available for the User Manual
and Special O󼴨ers.
User Manual
Benutzerhandbuch
Manuel d'utilisation
Manuale utente
Manual de usuario
Руководство пользователя
1
27
55
83
111
139
167
192
EN
IT
DE
ES
SA
FR
RU
HE


1
Safety Instructions
Warning
This product can be used by children aged from 8 years and above and persons
with physical, sensory, intellectual de󼴩ciencies, or limited experience or knowledge
under the supervision of a parent or guardian to ensure safe operation and to
avoid any risk of hazards. Cleaning and maintenance shall not be made by children
without supervision.
The vacuum is not a toy. Children shall not play with or operate this product. Please
exercise caution when using the vacuum near children. Do not allow children to
clean or maintain the vacuum unless supervised by a parent or guardian.
Do not use the vacuum outdoors or on wet surfaces. Only use the vacuum on dry
indoor surfaces. Do not touch the plug or any part of the vacuum with wet hands.
To reduce the risk of 󼴩re, explosion, or injury, check to make sure the lithium battery
and charging adapter are undamaged before use. Do not use the vacuum if either
the lithium battery or charger is damaged.
The smart multi-brush bar, mini electric brush, battery, carbon 󼴩ber rod, and
vacuum are electrically conductive and should not be immersed in water or other
liquid. Make sure to dry all 󼴩lters after cleaning.
Prevent injury caused by moving parts. Turn o󼴨 the vacuum before cleaning the
smart multi-brush bar. The smart multi-brush bar, dust cup and 󼴩lter must all be
properly installed before using the vacuum.
Only use the original charging adapter. Never use an unoriginal adapter, as this may
cause the lithium battery to catch 󼴩re.
Do not use the vacuum to pick up 󼴪ammable or combustible liquids, such as
gasoline, or bleach, ammonia, drain cleaners or other liquids.
Do not use the vacuum to pick up sharp or hard objects, such as glass, nails, screws,
or coins, which may damage the machine. Do not use the vacuum to pick up drywall
particles, ashes like 󼴩replace ash, or smoking or burning materials such as coal,
cigarette butts, or matches.
Check the area to be cleaned before use. To prevent the openings from being
blocked, clear the larger paper, spitball, plastic cloth or sharp objects (such as glass,
nails, screws, coins, etc.) and any object which is larger than openings.
Keep hair, loose clothing, 󼴩ngers and other parts of the body away from the
vacuum's openings and moving parts. Do not point the hose, wand or tools at your
eyes or ears or put them in your mouth.
Do not put any object into the vacuum's openings. Do not use the vacuum with
any opening blocked. Keep free of dust, lint, hair, or other items which may reduce
air󼴪ow.
Do not rest the vacuum against a chair, table, or other unstable surface, as this may
cause damage to the machine or personal injury.
To prevent accidents including electric shock or 󼴩re caused by improper use, please
read this manual carefully before use and retain it for future reference.
EN
2
If the vacuum becomes damaged or is otherwise malfunctioning, please contact our
authorized service department. Never attempt to disassemble the device on your
own.
All instructions in the manual for recharging the battery must be strictly followed.
Failure to properly charge the battery within the speci󼴩ed temperature range could
damage the battery.
Make sure the vacuum is unplugged when not used for extended periods as well as
prior to performing any maintenance or repairs.
Please be extra careful when using the vacuum to clean stairs.
Do not install, charge, or use this product outdoors, in bathrooms, or around a pool.
Fire Hazard Warning: Do not apply any type of fragrance to the vacuum's 󼴩lter.
These types of products are known to contain 󼴪ammable chemicals which may
cause the vacuum to catch 󼴩re.
This product is designed for home use only.
Only use the original charger (Model ZD024M340090EU/ZD024M340090AU).
Only use the approved battery type (Model P2033-8S1P-PAA).
Do not use and store in extremely hot or cold environments (below 0℃ /32° F or
above 40℃ /104° F). Please charge the cordless vacuum in temperature above 0℃
/32° F and below 40℃ /104° F.
We Dreame Trading (Tianjin) Co., Ltd., hereby, declares that this equipment is in
compliance with the applicable Directives and European Norms, and amendments.
The full text of the EU declaration of conformity is available at the following internet
address: www.dreame-technology.com
For detailed e-manual, please go to https://www.dreame-technology.com/pages/
user-manuals-and-faqs
EN
3
Product Overview
Accessories
Note: The images in this manual are for illustrative purposes only. The actual product may
di󼴨er.
2-in-1 Charging
& Storage Mount
(Including screws ×2,
wall plugs ×2, and
mounting template
sticker )
Smart Multi-Brush BarCharger
LED Crevice NozzleCarbon Fiber Rod
Extension Hose
2-in-1 Brush NozzleFlexible Adapter Mini Electric BrushSoft Dusting Brush
EN
4
Product Overview
Component Names
Display Screen
Antistatic Contact
Carbon Fiber Rod
Release Button
Brushbar Head Release
Button
Carbon Fiber Rod
Smart Multi-Brush Bar
Charging Port
Dust Cup
LED Battery Status Indicator
On/O󼴨 Switch
Press to turn on
Release to turn o󼴨
Battery Release Button
Dust Cup Bottom Cover
Release Button
EN
5
Product Overview
The color of dust level indicator changes with the amount of inhaled dust.
Residual time is for reference only and it may be di󼴨erent from the actual time.
Note:
Switching Suction Level
Press brie󼴪y to switch the
suction level
Lock Status
Dust Level Indicator
Suction Level Status
Residual Running-Time
Dust Level Monitoring Curve
The color of curve changes
with the amount of dust in
real time
Red: High
Orange: Med
Green: Low
Electronic Lock/Reset Filter
Press brie󼴪y to enter/exit
lock
Press and hold for 1.5
seconds to enter the 󼴩lter
reset interface
Introduction of Display Screen
EN
6
Installation
Vacuum Installation
Diagram
Click
Click
EN
7
Installation
Accessories Installation
Diagram
Click
Click
EN
8
Click Click
Click
Accessories Installation Diagram
Installation
EN
9
2-in-1 Charging & Storage Mount Installation Diagram
(The 2-in-1 charging & storage mount is an optional accessory. You can install it based on
your needs.)
*30cm: Leave enough space just in case you
may need to purchase the replaceable battery
in the future.
1. The bottom of the mounting template sticker should be level and at least 103cm from
the ground. The top should have at least 30cm* of clearance above it.
2. Use a power drill with an 8mm drill bit to drill a hole into each marker on the mounting
template sticker, then insert a wall plug into each hole.
3. Align the locating holes on the mount with the holes on the wall. Fasten it to the wall
with the included screws.
Note:
The 2-in-1 charging & storage mount should be installed in a cool, dry place with an
electrical outlet nearby. Prior to installing, ensure that there are no electrical wires or
pipes in the space directly behind where the mount will be installed.
Installation
103 cm
30 cm
EN
10
Charging
Note: Once the vacuum is fully charged, the
indicator will turn o󼴨 after 5 minutes, and
the vacuum will enter energy-saving mode.
Charging the vacuum with the charger Charging the vacuum on the charging mount
Charging Methods
1
2
LED Battery Status IndicatorDisplay Screen
Battery Status Display
When charging, the indicators blink white.
When the charging is completed, the
indicators keep solid white.
The number on the display screen
represents the current battery level in a
percentage during charging. When the
number becomes 100, the battery is fully
charged.
Fully charge the vacuum before using it for the 󼴩rst time.
A full charge will take approx. 4 hours.
Vacuuming in Turbo Mode for a prolonged period will cause the battery to heat up, which
increases charging time. Allow the vacuum to cool down for 30 minutes before charging it.
Note:
EN
11
How to Use
Setting Language
Note: Stop the vacuum at any time while cleaning. It will continue to use the last selected
suction level when starting again.
Switching Suction Level
Press the button to switch between four suction levels of auto, eco, med and turbo. The
corresponding suction level will be highlighted on the display screen.
The color of dust level indicator changes with the amount of inhaled dust. When the
smart multi-brush bar is attached, the vacuum will automatically switch the suction level
between the 󼴪oor/tile and the carpet.
Press and hold the button for 3 seconds to enter the menu interface. Click the button
to swtich to "Language". Press the button for 1 second to enter the language selection
interface. Click to scroll through the language list, select a language, and then press
and hold for 3 seconds to save your setting.
Cleaning Record
Press and hold the button for 3 seconds to enter the menu interface. Click the button
to swtich to "Cleaning Record" and press the button for 1 second to enter the cleaning
record interface. Then you will see the cleaning record of the last 7 days.
The display screen will return to the main page if there is no operation for more than 15 seconds.
To exit the menu interface, click the button to select "Exit".
Note:
EN
12
How to Use
Working Methods
Note:
In this mode, brie󼴪y press the on/o󼴨 switch to suspend the operation or start again and
the working mode of the vacuum will not change.
Click the electronic lock again to quit Continuous Cleaning Mode.
Select from two working methods for the vacuum, which can be selected based on your
own needs.
When the vacuum is running, it will monitor the amout of inhaled dust within 1 second. The
amount of dust will be displayed by the color of dust level monitoring curve on the screen
in real time.
Method 1: Discontinuous Cleaning Mode
Press and hold the switch of the vacuum to enable this mode, and release it to stop
immediately.
Method 2: Continuous Cleaning Mode (Electronic Lock)
Click the electronic lock key to switch to Continuous Cleaning Mode, and then brie󼴪y press
the on/o󼴨 switch to keep the vacuum in Continuous Cleaning Mode.
Use the electronic lock to free your 󼴩ngers from fatigue caused by holding the switch.
EN
13
Using Di󼴨erent Accessories
Smart Multi-Brush Bar
For cleaning 󼴪oors such as marble, tile,
and low pile carpet. When Auto Mode is
activated, the vacuum will automatically
adjust its suction level depending on the
surface type.
Note: The smart multi-brush bar can be
attached directly to the vacuum.
Mini Electric Brush
For vacuuming dirt, pet hair, and other
stubborn debris from sofas, bedding, and
other fabric surfaces.
Note: It is not recommended to vacuum
on fragile surfaces, such as silk.
How to Use
2-in-1 Brush Nozzle Soft Dusting Brush
For vacuuming dust from curtains,
keyboards, ceilings, sofas, vehicle
interiors, co󼴨ee tables, etc.
Suitable for vacuuming on LCDs,
keyboards, lampshades, curtains, shutters
and other surfaces of fragile objects.
EN
14
How to Use
Note:
If any rotating part becomes stuck, the vacuum may shut o󼴨 automatically. Remove any
trapped objects so the device can function normally.
When the battery becomes overheated, the vacuum will automatically shut o󼴨. Wait until
the battery temperature returns to normal, then the vacuum will work normally.
Extension Hose
It is suitable for vacuuming the corners that are not easily accessible such as drawers, cars
interior, and in the bottom of sofa when used with soft dusting brush or 2-in-1 brush nozzle.
Flexible Adapter LED Crevice Nozzle
Bending and extending the rod with one
click can easily reach under low-lying
furniture, such as bed and sofa.
The nozzle is equipped with a thin suction
opening and LED light. It is suitable for
vacuuming the debris in the narrow places.
EN
15
Care & Maintenance
Tips:
1. Always use genuine parts to keep your warranty from becoming void.
2. If the 󼴩lter or nozzle becomes clogged, the vacuum will stop working shortly after being
turned on. To restore normal functions, clean the 󼴩lter and/or nozzle.
3. If the vacuum is not be used for an extended period, fully charge it, unplug its charger,
and store it in a cool, low-humidity environment away from direct sunlight. To avoid
over-discharging the battery, recharge the vacuum at least once every three months.
2. Push the dust cup release switch in the direction indicated by the arrow, then gently
remove the dust cup from the vacuum.
Cleaning the Vacuum
Wipe the vacuum with a soft dry cloth.
Cleaning the Dust Cup, Pre-Filter, and Cyclone Assembly
The vacuum's cleaning ability will be reduced if the dust cup is 󼴩lled to the "MAX" mark.
To regain performance, empty the dust cup in a timely manner. Before emptying the cup,
make sure the vacuum is disconnected from the power, and do not press its power button.
1. Press the dust cup bottom cover release button, then empty the contents.
2
1
1
EN
16
Care & Maintenance
3. Remove the pre-󼴩lter 󼴩rst, then lift the handle of the cyclone assembly and turn it
counterclockwise until it stops, then pull to lift out the cyclone assembly.
Note: It is recommended to clean the pre-󼴩lter at least once every 3 months and the
cyclone system at least once every 6 months.
1
2
3
Pre-FilterCyclone Assembly
4. Wipe the dust cup with a soft wet cloth. Pay attention to wring out the discloth before
using.
5. Rinse the cyclone assembly and pre-󼴩lter until they are clean. After washing, air dry for
at least 24 hours .
12
6
111
57
210
48
39 24 hrs
To reduce the risk
of electric shock, do
not rinse the dust
cup with water.
EN
17
Installing the Dust Cup, Pre-Filter, and Cyclone Assembly
1. Insert the cyclone assembly vertically into the dust cup, and make sure that the handle
of the cyclone assembly line up with the slot on the left side of the dust cup. Turn the
handle clockwise until it locks, then 󼴪ip the handle down.
2. Place the pre-󼴩lter with its front side facing up into the cyclone assembly.
3. Slightly tilt the dust cup so its slot aligns with the clip on the vacuum. Then gently push
the dust cup until it clicks into place.
3
1
2
3
Care & Maintenance EN
1/221