Kichler 300395WH Manuel utilisateur

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

56” ICON CEILING FAN

Model #300395

READ AND SAVE THESE INSTRUCTIONS

KICHLER.COM

Net Weight: 8.63 kg (19.02 lb)

Gross weight: 10.45 kg (23.04 lb)

56” ICON | 3

SAFETY RULES

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

MOUNTING OPTIONS

HANGING THE FAN

INSTALLATION OF SAFETY SUPPORT

(CANADA ONLY)

ELECTRICAL CONNECTIONS

FINISHING THE INSTALLATION

ATTACHING THE FAN BLADE ARMS

ATTACHING THE FAN BLADES

INSTALLING THE LIGHT KIT FIXTURE

INSTALLING GLASS SHADE

CONTROL SYSTEM SET-UP

BUTTON INSTRUCTIONS

INSTALLING WALL PLATE

INSTALLING THE TRANSMITTER

OPERATING INSTRUCTIONS

TROUBLESHOOTING

FCC INFORMATION

TABLE OF CONTENTS

Read all instructions BEFORE assembly and USE of product

KEEP INSTRUCTIONS FOR FUTURE USE

4

6

7

8

11

12

14

15

16

17

19

20

21

22

23

24

| KICHLER.COM

4

SAFETY RULES

WARNING: FOR CANADA, THIS FAN MUST BE SECURED

DIRECTLY TO THE BUILDING STRUCTURE/CEILING

JOIST. DON’T SECURE THIS FAN TO AN OUTLET BOX.

1. CAUTION - RISK OF SHOCK -

Disconnect power at the main circuit breaker panel

or main fusebox before starting and during the

installation.

2. WARNING: This fixture is intended for installation in

accordance with the National Electrical Code (NEC) and

all local code specifications. If you are not familiar with

code requirements, installation by a certified electrician

is recommended.

3. WARNING: To reduce the risk of fire, electric shock, only

use the control provided with fan.

4. WARNING: To reduce the risk of fire, electric shock,

or Personal Injury mount to an outlet box marked

“Acceptable For Fan Support of up to 15.9 kg (35 lb)”.

For outlet box mounting, use mounting screws (and

lock washers) provided with the outlet box. Most outlet

boxes commonly used for the support of light fixtures

are not acceptable for fan support and may need to

be replaced. Due to the complexity of the installation

of this fan, a qualified licensed electrician is strongly

recommended.”

5. All wiring must be in accordance with the National

Electrical Code ANSI/NFPA 70 and local electrical codes.

Electrical installation should be performed by a qualified

licensed electrician.

6. The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum of

15.9 kg (35 lb). Use only CUL Listed outlet boxes marked

“FOR FAN SUPPORT”.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN TO OUTLET

BOX MARKED “ACCEPTABLE FOR FAN SUPPORT”.

7. CAUTION: The fan must be mounted with a minimum

of 2.1m (7 feet) clearance from the trailing edge of the

blades to the floor.

8. To operate the reverse function on this fan, press the

reverse button while the fan is running.

9. Avoid placing objects in the path of the blades.

10. To avoid personal injury or damage to the fan and other

items, be cautious when working around or cleaning the

fan.

11. WARNING: Make sure the power is disconnected before

cleaning the fan.

READ AND SAVE THESE INSTRUCTIONS

56” ICON | 5

12. Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened

cloth will be suitable for most cleaning.

13. After making the electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be

spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the

outlet box and the ungrounded conductor on the

other side of the outlet box.

14. Electrical diagrams are reference only. Light Kits

that are not packed with the fan must be cULus listed

and marked suitable for use with the model fan you

are installing. Switches must be cULus General Use

Switches. Refer to the Instructions packaged with the

light kits and switches for proper assembly.

15. All set screws must be checked, and re-tightened

where necessary, before installation.

WARNING: TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS (ALSO REFERRED

TO AS BLADE ARMS) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS IN THE PATH

OF BLADES.

16. WARNING: Chemical Burn Hazard. Keep batteries

away from children.; and

This product contains a lithium button/coin cell

battery. If a new or used lithium button/coin cell

battery is swallowed or enters the body, it can cause

severe internal burns and can lead to death in as little

as 2 hours. Always completely secure the battery

compartment. If the battery compartment does

not close securely, stop using the product, remove

the batteries, and keep it away from children. If you

think batteries might have been swallowed or placed

inside any part of the body, seek immediate medical

attention.

a) The cells shall be disposed of properly, including

keeping them away from children; and

b) Even used cells may cause injury.

SAFETY RULES (continued)

!

| KICHLER.COM

6

TOOLS REQUIRED PACKAGE CONTENTS

• Philips screw driver

• Blade screw driver

• 11mm wrench

• Step ladder

• Wire cutters

Unpack your fan and check the contents.

You should have the following items:

a. Fan blades (5)

b. Canopy

c. Ball/Downrod assembly

d. Coupling cover

e. Fan motor assembly

f. Blade arms (5)

g. Light kit assembly

h. Glass shade assembly

i. Receiver

j. Wall transmitter

k. Parts bag contents:

1) Mounting hardware:

Star washers (2), wire nuts (3),

machine screws (2), washers (2),

wood screws (2)

2) Blade attachment hardware:

blade screws (16), blade arm

screws (11), fiber washers (16)

3) Safety cable hardware:

wood screw, lock washer, flat

washer

4) Balancing kit

a.

b.

c.

d.

e.

f.

g.

h.

i.

j.

k.

56” ICON | 7

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting plate

Outlet box

ANGLED CEILING

MAXIMUM 20°

ANGLE

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the full weight of the fan (up

to 15.9 kg (35 lb)). Do not use plastic outlet boxes.

Figures 1, 2, and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A minimum

clearance of 12” is suggested for optimal operation.

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist Hanger”

for the support of the outlet box. Make sure the joist hanger you

purchase has been designed for use with ceiling fans. (Fig. 4)

Fig. 2

Fig. 1

Fig. 3

Fig. 4

| KICHLER.COM

8

HANGING THE FAN

NOTE: FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY

TO THE BUILDING STRUCTURE/CEILING JOIST. DON’T SECURE

THIS FAN TO AN OUTLET BOX. (see Fig. 6A)

REMEMBER to turn o the power before you begin.

To properly install your ceiling fan, follow the steps below.

Step 1. Remove the decorative canopy bottom cover from the

canopy by turning the cover counterclockwise. (Fig. 5)

Step 2. Remove the ceiling mounting bracket from the canopy by

removing (and save) one of the two screws. Loosen the remaining

screw by a half turn. (Fig. 5)

Step 3. Pass the 120 volt supply wires from the ceiling outlet box

through the center of the ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to the outlet box using

the screws and washers included with the outlet box. (Fig. 6)

Step 4A. Secure the mounting bracket directly to a joist from the

building structure. Use only the appropriate wood screws and lock

washers included with your fan. (Fig. 7)

NOTE: THIS STEP IS ONLY FOR CANADA.

CAUTION: The hanger bracket must be installed directly to the

building joist using the two wood screws and washers provided.

(Fig. 7)

Fig. 6

Fig. 5

Fig. 7

Ceiling

mounting

bracket

Canopy

Canopy cover

120V Wires

Ceiling

hanger

bracket

Mounting screws

(supplied with electrical box)

UL Listed

electrical box

Washers

120V Wires

Hanger bracket

Ceiling joist

#10 Wood screws

Lock washers

56” ICON | 9

Step 5. Remove the hanger ball from the downrod assembly by

loosening the set screw, unscrewing and removing the cross pin and

unscrewing the ball o the rod. (Fig. 8)

Step 6. Loosen the two set screws and remove the hitch pin and

retaining clip from the coupling on top of the motor assembly. (Fig. 9)

Step 7. Carefully feed the electrical lead wires from the fan up

through the downrod. Thread the downrod into the coupling until the

hitch pin holes align.

Next, replace the hitch pin and retaining clip. Tighten both set screws.

(Fig. 9)

Fig. 8

Fig. 9

HANGING THE FAN (continued)

Cross pin

Hanger ball

Downrod

Supply wire &

Safety cable

Downrod

Retaining

clip

Hitch pin

Set screws

Coupling

Set screws

| KICHLER.COM

10

Step 8. Slip the coupling cover, canopy cover and canopy onto the

downrod. (Fig. 10)

Thread the hanger ball onto the downrod, insert the cross pin

through the downrod and tighten. Tighten the set screw.

Step 9. Lift the motor assembly into position and place the

hanger ball into the ceiling mounting bracket.

Rotate the entire assembly until the “Check Tab” has dropped into

the “Registration Slot” and seats firmly. (Fig. 11)

The entire motor assembly should not rotate (left or right) when

seated properly.

WARNING: Failure to reattach the cross pin and seat the

“Check Tab” can cause the fan to fall from the ceiling during

operation. Take special care to make sure this pin is reattached.

HANGING THE FAN (continued)

Registration

slot

Check

tab

Cross pin

Hanger ball

Set screw

Downrod

Coupling

Canopy

Canopy cover

Coupling cover

Supply wires & Safety cable

Fig. 10

Fig. 11

56” ICON | 11

INSTALLATION OF SAFETY SUPPORT

(Required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan

from falling, please install it as follows.

Step 1. Attach the provided wood screw and washers to the ceiling

joist next to the mounting bracket but do not tighten. (Fig. 12)

Step 2. Adjust the length of the safety cable to reach the screw and

washers by pulling the extra cable through the cable clamp until the

overall length is correct, put the end of the cable back through the

cable clamp, forming a loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of the safety cable over

the wood screw securely.

NOTE: Although the safety support cable is required for Canadian

installations only, it’s a good idea to make the attachment with

any installation.

Fig. 12

Hanger bracket

Safety cable Attach safety cable

to ceiling joist with

screw and washer

| KICHLER.COM

12

ELECTRICAL CONNECTIONS

WARNING: Carefully read and retain this Instruction Manual for

future reference.

WARNING: To avoid possible electrical shock, be sure the

electricity is turned o at the main panel by removing the fuse or

opening the circuit breaker.

WARNING: This control is designed for use with “DC Motor

Ceiling Fans” ONLY. DO NOT use with any other type of electrical

appliance.

WARNING: All wiring must conform to national and local electrical

codes. If you feel you do not have enough electrical knowledge,

have a licensed electrician install the control.

Step 1. Insert the receiver into the ceiling mounting bracket with the

flat side of the receiver facing the ceiling. (Fig. 13)

For best performance, make sure the Black antenna, on the end

of the receiver, remains extended and not tangled with any of the

electrical wires. Fig. 13

Receiver

Hanger

bracket

56” ICON | 13

Fig. 14

White (Neutral)

Green or Bare

Copper (Ground)

White ("AC IN N")

Outlet box

Black (Hot)

Black ("AC IN L")

Receiver

Blue (For light)

Green-

(ground)

Orange (Motor)

Brown (Motor)

Grey(Motor)

(Connect to ground

wire on hanger

bracket if no house

ground wired)

Filter

White (For light)

A. Fan wire connection (Fig. 14)

Connect the orange wire from the fan to the orange wire on the receiver.

Connect the brown wire from the fan to the brown wire on the receiver.

Connect the grey wire from the fan to the grey wire on the receiver.

Connect the blue wire from the fan to the blue wire on the receiver.

Connect the white wire from the fan to the white wire on the receiver.

Secure the wire connections with the plastic wire nuts provided.

Align the black wire from the receiver to the brown wire from the filter,

align the white wire from the receiver to the blue wire from the filter, then

connecting the molded adaptor together.

Connect the black (hot) wire from the ceiling to the brown wire from the

filter box.

Connect the white (Neutral) wire from the ceiling to the blue wire from the

filter box.

Secure the wire connections with the plastic wire nuts provided.

If your outlet box has a ground wire (green or bare copper) connect it to

the fan ground wires; otherwise connect the hanging bracket ground

wire to the mounting bracket. Secure the wire connection with a plastic

nut provided. After connecting the wires, spread them apart so that the

green and white wires are on one side of the outlet box and black and blue

wires are on the other side. Carefully tuck the wire connections up into the

outlet box.

NOTE: Remember to cut o excess lead wire from fan body before wiring

in order to install receiver and canopy easily.

ELECTRICAL CONNECTIONS (continued)

| KICHLER.COM

14

FINISHING THE INSTALLATION

Step 1. Tuck all the connections neatly into the ceiling outlet box.

Step 2. Slide the canopy up to the mounting bracket and place one of

the key hole slots over the mounting screw on the mounting bracket.

Rotate the canopy until the screw head locks in place at the narrow

section of the key hole. (Fig.15)

Step 3. Align the remaining circular hole on the canopy with the

remaining hole on the Ceiling Mounting Bracket. Insert and tighten

the mounting screw you removed earlier and the mounting screw

from step 2 above. Now, attach the canopy cover to the mounting

screw heads by inserting the screw heads into the bottom side of the

canopy cover and rotating the cover clockwise.

NOTE: Adjust the canopy screws as necessary until the canopy

and canopy cover are snug.

WARNING: Make sure the “Check Tab” at the bottom of the

hanger bracket is properly seated in the “Registration Slot” on

the side of the hanger ball before attaching the canopy to the

bracket. Failure to properly seat the “Check Tab” could damage

the electrical wires when the ceiling fan blade direction is changed

while the fan is running.

Fig. 15

Outlet box

Ceiling

mounting

bracket

Canopy

cover

Screw

Filter Receiver

56” ICON | 15

ATTACHING THE FAN BLADES

Step 1. Align the holes from the blade and washer to the holes from

the blade arms, and secure the blade in place with screws provided.

(Fig. 17)

Step 2. Repeat these steps for the remaining four blades.

Fig. 16

Fig. 17

ATTACHING THE FAN BLADE ARMS

Step 1. Fasten the blade arm to the fan motor assembly by tightening the

blade arm screw onto the fan motor assembly. (Fig. 16)

Step 2. Repeat this procedure for the remaining four blade arms.

Screw

Fan motor assembly

Blade arm

Fan motor assembly

Blade

Screw

Washer

| KICHLER.COM

16

INSTALLING THE GLASS SHADE

Raise the glass shade against the light plate and secure by tightening

the nut and finial. (Fig. 20)

Fig. 19

Fig. 20

Fig. 18

INSTALLING THE LIGHT KIT FIXTURE

CAUTION: “To reduce the risk of electric shock, disconnect the

electrical supply circuit to the fan before installing light kit.”

Step 1. Remove the finial, and nut from the threaded nipple of the

light kit fixture assembly. (Fig. 18)

Step 2. Loosen, remove, and save the four screws on the mounting

ring, attached to the motor shaft. Connect the wire from the light

kit fixture assembly to the wire from the fan motor assembly by

connecting the molded adaptor plug together.

Step 3. Align the screw holes from the light kit pan with the screw

holes on the mounting ring of the fan motor assembly. Reinstall

and tighten the four screws previously removed in step 2 securely.

(Fig. 19)

Light kit pan

Screws

Fan motor assembly

Finial

Light kit pan

Nut

Fan motor

assembly

Light kit pan

Shade

Finial

Nut

A

B

56” ICON | 17

WARNING:Chemical Burn Hazard.Keep

batteries away from children.See Manual

Model : UC7214T

FCC ID : CHQ7214T

WARNING:Chemical Burn Hazard.Keep

batteries away from children.See Manual

ON

Dip switch

Model : UC7214T

FCC ID : CHQ7214T

WARNING:Chemical Burn Hazard.Keep

batteries away from children.See Manual

CONTROL SYSTEM SET-UP

WARNING: Chemical Burn Hazard. Keep batteries away from

children.

WARNING: Make sure the power is completely disconnected

before you begin this procedure.

SPECIAL NOTE: Your new Kichler® Ceiling Fan is state of the art

and employs a high eciency DC (direct current) motor with an

advanced CoolTouch™ remote control system. The DC motor

uses 70% less energy than a conventional ceiling fan AC induction

motor. The DC motor is “digitally” controlled and operates

dierently than conventional ceiling fan motors.

Please read this portion of the manual completely before

proceeding.

Our CoolTouch™ Control System includes an “automatic

frequency selection” feature. To set the control frequency and

program the control system, follow these steps:

Open the back of the transmitter by loosening the screw (figure

21). The frequency selector is a “dip switch block” inside the

battery compartment of the transmitter (see figure 22). You

change frequencies by arranging the small switches numbered

1 through 4 in a up or down position. 16 Possible frequencies

or combinations are possible. The fifth switch, marked D and X

sets the system for operation with incandescent or fluorescent

lamps. It is essential to set this switch correctly. If your ceiling

fan is equipped with incandescent lamps set this switch to the D

position, for fluorescent lamps, set the switch to the X position.

If these settings are reversed, the lighting control system will

operate erratically and could damage your ceiling fan.

Fig. 21

Fig. 22

!

| KICHLER.COM

18

System programing: Read all of these steps before proceeding.

Each step must be followed exactly to properly program the control system.

1. You can leave the frequency switches at the factory setting or move them to any combination of up or

down. Use a small flat bladed screwdriver to move the switches.

2. Insert both batteries and make sure they are seated correctly in each recess with the positive + sign

facing up. Replace the battery cover. (Figure 21)

3. Test the transmitter by pushing and releasing ANY button briefly. A Blue Light should illuminate under

the 3-4 buttons. (Fig. 23) If not, check to make sure the batteries are inserted and seated correctly.

Power Up and Programming:

4. Follow the below steps to set the remote control:

The auto learning function will only mandate within 60 seconds when turning the fan’s AC power ON.

(Figure 24)

5. Select desired frequency from the back of transmitter.

6. From the back of the transmitter, press and hold the “hold ” button for 5+ seconds. Once the receiver

has detected the frequency, the light will flash twice, and the fan will automatically begin to operate

and start to rotate in the counter clockwise direction and on the highest RPM for 3 minutes. When

counterclockwise rotation has finished, the fan will automatically reverse to clockwise direction again

to the highest RPM for 3 minutes. Fan will shut o when the self calibration test has finished. The total

self calibration test will last about 6 minutes.

NOTE: If the self calibration test failed, turn the AC power o; restore power and process the self

calibration test again.

NOTE: During self calibration test, the remote is non-fuctional.

NOTE: The learning frequency function and self calibration test will continue to retain the last set

frequency and calibration set even when the AC power is shut o. If the frequency is changed the self

calibration test will occur again.

7. Your CoolTouch™ Control System is now programmed and ready for use. Please see the Operating

Instructions.

The receiver provides the following protective function:

1. Lock position: The DC motor has a built-in safety against obstruction during operation. If there is an

obstruction, the motor will stop and then the power will automatically go o in 30 seconds. Remove

the obstruction and reset.

2. Over 80W protection: When the receiver detects motor power consumption which is greater than

80W, the receiver power will be stopped and operation will immediately discontinue. Wait for 5 seconds

and then turn the receiver power back on.

Fig. 23

Fig. 24

Blue Light

Press/hold Button

56” ICON | 19

BUTTON INSTRUCTIONS

Figure 25

Buttons 1, 2, 3, 4, 5 and 6 are used to set the blade speed as follows:

1 = Low Speed

2 = Medium Low Speed

3 = Medium Speed

4 = Medium High Speed

5 = High Speed

6 = Extra High Speed

Figure 26

The “MOTOR OFF” button:

This button turns the fan motor o and is also used in the program procedure.

The “LIGHT CONTROL “ button:

This button turns the bottom light ON or OFF and also controls the brightness

setting. Press and hold either button to set the desired brightness level. The

next time you turn the light on, the system will remember this setting. Press

and release either button to turn the light ON or OFF.

Figure 27

The “FORWARD/REVERSE “ button is used to set the fan in forward or reverse

operation. Each time you press this button the fan blades will reverse direction.

This button functions ONLY when the fan blades are in motion.

OPERATIONAL NOTE: Each time you start the blades rotating, at any speed

or reverse, the direction of the blades the Control System will do a “Self Check”

to ensure operational integrity. The blades will rotate slowly a short distance

(¼ turn), pause, change directions, rotate ¼ turn, then build up RPM’S to the

selected speed.This is a perfectly normal procedure and ensures normal

operating performance Fig. 27

Fig. 25

Motor Off Button

Light Control Buttons

Forward/Reverse

Button

Speed Buttons

Fig. 26

| KICHLER.COM

20

INSTALLING THE COOL TOUCHTM

CONTROL SYSTEM WALL PLATE

Select a location to install the Wall Control System Transmitter and

Wall Plate.

WARNING: All wiring must be in accordance with the National

Electrical Code and local electrical codes. Electrical installation

should be performed by a qualified licensed electrician.

Select a location to install your CoolTouch™ Control System

Transmitter. You can replace an existing wall switch or, install the

transmitter on ANY flat surface.

Option 1: Install the control system using an existing wall switch

outlet box. Make sure the electrical power is TURNED OFF at the

main panel before continuing.

NOTE: Switch installation must comply with all local and national

electric codes.

Step 1. Remove the existing wall plate and the old switch from the

wall outlet box. Wire nut the BLACK leads (hot) together and push

back inside the outlet box. (Fig. 28)

Step 2. Install the metal plate and CoolTouch™ wall plate to the

existing wall outlet box with 4 screws provided. Then place the two

plastic plugs into the wall plate. (Fig. 29)

Option 2: Install the control system on ANY flat surface.

Select the desired location and use the CoolTouch™ wall plate to

mark the location for the mounting holes. Use the dry wall anchors

and/or screws provided and finish the installation.

Wall plate

Switch

Outlet box

Screws

Plastic plugs

CoolTouch

™

wall plate

Outlet box Metal plate

Fig. 29

Fig. 28

La page charge ...

Kichler 300395WH Manuel utilisateur

Ce manuel convient également à

Kichler 300395WH Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents