Kichler 300285WZC Manuel utilisateur

85" GENTRY XL

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

REV 1-JUN-2021

TABLE OF CONTENTS

SAFETY RULES.......................................................................... 4

5

6

7

10

11

13

14

TOOLS REQUIRED....................................................................

PACKAGE CONTENTS.............................................................

MOUNTING OPTIONS.............................................................

HANGING THE FAN..................................................................

INSTALLATION OF SAFETY SUPPORT..........................

ELECTRICAL CONNECTIONS.............................................

FINISHING THE INSTALLATION........................................

INSTALLING THE LIGHT PLATE........................................

INSTALLING THE LED LIGHT KIT

AND GLASS SHADE ASSEMBLY......................................15

16

17

18

19

20

21

CONTROL SYSTEM SET-UP...............................................

BUTTON INSTRUCTION........................................................

INSTALLING THE WALL CONTROL

SYSTEM WALL PLATE...........................................................

OPERATION INSTRUCTIONS............................................

TROUBLESHOOTING............................................................

85" GENTRY XL | 3

ATTACHING THE FAN BLADES..........................................

SENSORLESS DC CONTROL PAIRING

PROCEDURES...........................................................................

FCC INFORMATION............................................................... 22

cULus Model: 300285/CP183616/85-GENT

Net Weight: 15.5KGS Gross Weight: 18KGS

4 | KICHLER.COM

1. CAUTION - RISK OF SHOCK-

Disconnect Power at the main circuit breaker panel or main fusebox

before starting and during the installation.

2. WARNING: This xture is intended for installation in accordance with the

National Electrical Code (NEC) and all local code specications. If you are

not familiar with code requirements, installation by a certied electrician

is recommended.

3. WARNING: To reduce the risk of re, electric shock, or personal Injury

mount to an outlet box marked “Acceptable For Fan Support of up to 22.7

kg (50 lbs)”. For outlet box mounting, use mounting screws provided with

the outlet box. Most outlet boxes commonly used for the support of light

xtures are not acceptable for fan support and may need to be replaced.

Due to the complexity of the installation of this fan, a qualied licensed

electrician is strongly recommended.

4. All wiring must be in accordance with the National Electrical Code ANSI/

NFPA 70 and local electrical codes. Electrical installation should should

be performed by a qualied licensed electrician.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only cULus

Listed outlet boxes marked “FOR FAN SUPPORT”.

6. CAUTION: The fan must be mounted with a minimum of 2.1 m (7 feet)

clearance from the trailing edge of the blades to the oor.

7. To operate the reverse function on this fan, press the reverse button while

the fan is running.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

10. WARNING: Make sure the power is disconnected before cleaning the fan.

11. Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

12. After marking electrical connections, spliced conductors should be turned

upward and pushed carefully up into outlet box. The wires should be

spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box.

13. Electrical diagrams are reference only. Light Kits that are not packed with

the fan must be cULus Listed and marked suitable for use with the model

fan you are installing. Switches must be cULus General Use Switches.

Refer to the Instructions packaged with the light kits and switches for

proper assembly.

14. Suitable for damp location.

15. Use only with light kits marked suitable for damp location.

16. All set screws must be checked, and retightened where necessary, before

installation.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED “ACCEPTABLE FOR FAN SUPPORT”.

WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS (ALSO REFERRED TO AS FLANGES) DURING ASSEMBLY

OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN THE PATH OF

BLADES.

SAFETY RULES

READ AND SAVE THESE INSTRUCTIONS

WARNING: FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY TO THE

BUILDING STRUCTURE / CEILING JOIST. DON’T SECURE THIS FAN TO AN

OUTLET BOX.

TOOLS REQUIRED

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

PACKAGE CONTENTS

i

j

k

f

g

h

b

c

d

e

Unpack your fan and check the

contents. You should have the

following items:

a. Fan blades (9)

b. Blade support plates (9)

c. Canopy & Ceiling mounting bracket

d. Ball/downrod assembly

e. Coupling cover

f. Fan motor assembly

g. Light plate

h. 14W LED light kit

i. Glass shade assembly

j. Wall Transmitter

k. Part bag contents

1) Mounting hardware:

star washers (2), wire nuts (3),

machine screws (2), washers (2),

screws (2)

2) Blade attachment hardware:

screws (29)

3) Safety cable hardware:

wood screw, lock washer,

flat washer

4) Balance Kit

a

85" GENTRY XL | 5

6 | KICHLER.COM

If there isn't an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning off circuit breakers

Secure the outlet box directly to the building structure. Use appropriate

fasteners and building materials. The outlet box and its support must be

able to fully support the moving weight of the fan (at least 50 lbs). Do not

use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different ways to mount the outlet

box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted) ceiling,

you may need a longer downrod to maintain proper clearance between

the tip of the blade and the ceiling. A minimum clearance of 12" is

suggested for optimal operation.

NOTE: Depending on the location you have selected for installation, you

may need to purchase and install a "Joist Hanger" for the support of the

outlet box. Make sure the joist hanger you purchase has been designed

for use with ceiling fans. (Fig. 4)

MOUNTING OPTIONS

Fig. 1

Outlet box

Fig. 2

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Fig. 3

ANGLED CEILING

MAXIMUM 20° ANGLE

Outlet box

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Hanger bracket

Ceiling

canopy

Canopy

cover

HANGING THE FAN

NOTE: FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY TO

THE BUILDING STRUCTURE / CEILING JOIST. DON'T SECURE THIS

FAN TO AN OUTLET BOX. (SEE Fig. 6A)

REMEMBER to turn off the power before you begin

To properly install your ceiling fan, follow the steps below.

Step 1. Remove the decorative canopy bottom cover from the canopy

by turning the cover counter clockwise. (Fig. 5)

Step 2. Remove the ceiling mounting bracket from the canopy by

removing (and save one of the two screws. Loosen the remaining screw

by a half turn. (Fig. 5)

Step 3. Pass the 120 volt supply wires from the ceiling outlet box through

the center of the ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to the outlet box using the

screws and washers included with the outlet box. (Fig. 6)

Step 4A. Secure mounting bracket directly to a joist from the building

structure. Use only the appropriate wood screws lock washers included

with your fan. (Fig. 7) NOTE: THIS STEP IS ONLY FOR CANADA.

CAUTION! THE HANGER BRACKET MUST BE INSTALLED DIRECTLY

TO THE BUILDING JOIST USING THE TWO WOOD SCREWS AND

WASHERS PROVIDED. (Fig. 7)

85" GENTRY XL | 7

120V Wires

Hanger bracket

Ceiling joist

#10 Wood screws

Lock washers

120V Wires

Ceiling

hanger

bracket

Mounting screws

(supplied with

electrical box)

UL Listed

electrial

box

Washers

8 | KICHLER.COM

Step 5. Remove the hanger ball from the downrod assembly by

loosening the set screw, unscrewing and removing removing the cross

pin and unscrewing the ball off the rod. (Fig. 8

Step 6. Loosen the two set screws and remove the hitch pin and

retaining clip from the coupling on top of the motor assembly. (Fig. 9)

Step 7. Carefully feed the electrical lead wires from the fan up through

the downrod. Thread

the downrod into the coupling until the Hitch pin holes are aligned.

Next, replace the hitch pin and retaining clip. Tighten both set screws.

(Fig. 9)

HANGING THE FAN (continued)

Fig. 8

Fig. 9

Downrod

Cross pin

Hanger

ball Set screw

Supply wires

Downrod

Hitch pin

Retaining clip Set screws

Set screws

Fig. 10

Fig. 11

HANGING THE FAN (continued)

Step 8. Slip the coupling cover, canopy cover and canopy onto the

downrod. (Fig. 10)

Thread the hanger ball onto the downrod, insert the cross pin through

the downrod and tighten. Tighten the set screw.

Step 9. Lift the motor assembly into position and place the hanger ball

into the ceiling mounting bracket.

Rotate the entire assembly until the "Check Tab" has dropped into the

"Registration Slot" and seats firmly. (Fig. 11)

The entire motor assembly should not rotate (left or right) when seated

properly.

WARNING: Failure to reattach the cross pin and seat the "Check Tab"

can cause the fan to fall from the ceiling during operation. Take special

care to make sure this pin is reattached.

Registration slot

Downrod

Canopy

Canopy cover

Set screws

Hitch pin Retaining clip

Coupling cover

85" GENTRY XL | 9

10 | KICHLER.COM

A safety support cable is provided to help prevent the ceiling fan from

falling.

Step 1. Attach the provided wood screw and washers to the ceiling joist

next to the mounting bracket but do not tighten. (Fig. 12)

Step 2. Adjust the length of the safety cable to reach the screw and

washers by pulling the extra cable through the cable clamp until the

overall length is correct, put the end of the cable back through the cable

clamp, forming a loop at the end of the cable. Tighten the cable clamp

securely. Now, put the loop in the end of the safety cable over the wood

screw and under the washer. Tighten the wood screw securely.

NOTE: Although the safety support cable is required for Canadian

installations only. It's a good idea to make the attachment with any

installation.

Fig. 12

Ceiling mounting

bracket

Attach

safety cable

to ceiling joist

with screw and

washer

INSTALLATION OF SAFETY SUPPORT

ELECTRICAL CONNECTIONS

WARNING: Carefully read and retain this Instruction Manual for future reference.

WARNING:To avoid possible electrical shock, be sure the electricity is turned off at the main panel by removing the fuse or opening the circuit breaker.

WARNING: This control control is designed for use with "DC Motor Ceiling Fans" ONLY. DO NOT use with any other type of electrical appliance.

WARNING: All wiring must conform to national and local electrical codes. If you feel you do not have enough electrical knowledge, have a licensed

electrician install the control.

Make each of the wire connections illustrated in Figure 13. Secure each with the wire nuts provided. (Fig. 13)

A. Fan wire connection

Step 1. Black wire from the fan (motor) to the Black wire from the Wall Control's. (Fig. 13)

Step 2. White wire from the fan (motor) to the White (neutral) wire from the Household Supply. (Fig. 13)

Step 3. If your ceiling outlet box has a ground wire (green or bare copper) connect it to the ground wire from the ceiling fan and/or the ceiling mounting

bracket. (Fig. 13)

B. Wall control wire connection

Step 1. Black wire (TO MOTOR L) from the Wall Control to the Black wire from the Wall Outlet Box. (Fig. 13)

Step 2. Black wire (AC IN L) from the Wall Control to the Black wire from the Wall Outlet Box. (Fig. 13)

Step 3. If your wall outlet box has a ground wire (green or bare copper), connect the wall control's yellow/green ground wire to it; otherwise connect

the wall control's yellow/green ground wire directly to one of the screws from the wall outlet box. (Fig. 13)

85" GENTRY XL | 11

12 | KICHLER.COM

Fig. 13

Black White

Black

Ground

conductor

Outlet

box

Wall outlet box

Yellow/green ground

Black

White

Green

SUPPLY CIRCUIT

Fig. 14

Outlet box

Ceiling

mounting

bracket

Canopy

Canopy cover

Screws

Step 1. Tuck all the connections neatly into the ceiling outlet box.

Step 2. Slide the canopy up to the mounting bracket and place one of

the key hole slots over the mounting screw on the mounting bracket.

Rotate the canopy until the screw head locks in place at the narrow

section of the key hole. See figure 14.

Step 3. Align the remaining circular hole on the canopy with the

remaining hole on the Ceiling Mounting Bracket. Insert and tighten the

mounting screw you removed earlier and the mounting screw from

Step 2 above. Now, attach the canopy cover to the mounting screw

heads by inserting the screw heads into the bottom side of the canopy

cover and rotating the cover clockwise.

NOTE: Adjust the canopy screws as necessary until the canopy and

canopy cover are snug. (Fig. 14)

WARNING: Make sure the "Check Tab" at the bottom of the hanger

bracket is properly seated in the "Registration Slot" on the side of the

hanger ball before attaching the canopy to the bracket. Failure to

properly seat the "Check Tab" could damage the electrical wires when

to ceiling fan blade direction is changed while the fan is running.

FINISHING THE INSTALLATION

85" GENTRY XL | 13

14 | KICHLER.COM

Fig. 16

Fig. 15

INSTALLING THE LIGHT PLATE

Step 1. Loosen the two screws on the mounting ring attached to the

motor shaft and "remove" and save the third screw. (Fig. 16)

Step 2. Place the key hole slots on the light plate over the two screws

previously loosened on the mounting ring.

Turn the light plate until is locks in place at the narrow section of the key

hole slots.

Tighten both key hole screws and replace the third screw previously

removed and tighten securely.

Blades

Blade arms

Screws

Blade support

plates

ATTACHING THE FAN BLADES

Step 1. Align the holes from the blade and blade support plate to the

holes from the blade arms, and secure the blade in place with screws

provided. (Fig. 15)

Step 2. Repeat this process to attach the other two blades.

Light plate Mounting ring

Screws

85" GENTRY XL | 15

INSTALLING THE LED LIGHT KIT

AND GLASS SHADE ASSEMBLY

NOTE: Before starting installation, disconnect the power by turning off

the circuit breaker or removing the fuse at fuse box.

Step 1. Loosen the three mounting screws on the inside of the LED light

kit. (Fig.17)

Step 2. While holding the LED light kit under the fan motor, make the

wire connections: (Fig. 17)

- White to white

- Black to black

Step 3. Tuck the connections neatly into the light plate. Place the key

holes on the LED light kit over the 2 screws previously loosened from

the light plate, turn the LED light kit until it locks in place at the narrow

section of the key holes. Secure by tightening all three screws. (Fig.17)

Step 4. Raise the glass shade against the light plate and Secure by

tightening all three screws. (Fig. 18)

Fig. 17

Fig. 18

Wire connectors

LED light kit

Light plate

Screws

Glass shade

assembly

Screws

16 | KICHLER.COM

Fig. 19

CONTROL SYSTEM SET-UP

Green Light

For/Rev switch

Light status indicator

Fan speed indicator

Power switch

IMPORTANT: Ceiling fan blades MUST be installed before pairing

procedure can begin.

Program the wall control and/or the handset control separately. Once

the following pairing is successfully done, both the wall control and the

handset control can be used for the fan.

Press the power button on wall control to TURN THE POWER ON. The

LED lights on the wall control will blink thru the power up process,

approximately 3 seconds.

Press the “ ” power button to turn off the wall control (the button will

be up). Restore electricity to the ceiling fan branch circuit at the circuit

breaker or fuse box. Within 60 seconds of turning on the power, press

the “ ” power button to turn on the wall control (the button will be

down), and then press the " " reverse button for 3 to 5 seconds. Light

will blink twice. The remote will now be programmed to your fan and

ready for use.

IMPORTANT: Do not interrupt the conditioning until the fan comes to a

complete stop in approximately 5 minutes. All functions of the control

will be rejected during conditioning.

Try different speed setting on both the wall control and the handset

control to ensure the fan is now fully functional. If programming is

unsuccessful, retry the process starting from step 1 again.

85" GENTRY XL | 17

Fig. 20

LED Indicator Red LED: Transmitter signal indicator. When RF signal is

sending, the red light will illuminate.

Green LED: To show the Forward and Reverse indicator.

ON/OFF button " "

ON: Turn on the power.

OFF: Turn off the power

Reverse button " "

When the fan is running, press and release the Reverse button one time,

the fan will change operating direction.

Downflow: Green indicator LED will be off

Reverse: Green indicator LED will be on.

Light button " "

Press and release the Light button for light ON/OFF control.

Light indicator LEDs will show current light status. If the light kit is OFF,

the Light indicator LEDs are also all off. Press AND HOLD the light

button for more than 1 second and the light kit will begin dimming. Light

indicator LED will show the change in light level status. The light level

cycles from bright to dim and back to bright when the light button is

held.

Fan control " "

Press and release the Fan speed button for Fan ON/OFF control.

Fan indicator LED will illustrate the current fan speed. If the fan is OFF,

the fan speed indicator LEDs will also be OFF. Press and hold Fans

speed button for more than 1second to begin adjusting the fan speeds.

The indicator LEDs will shows the current speed level. The fan speed

adjustments adjust in a repeat cycle when the speed button is held

down. The speeds adjust from High to Low, then back up to High.

BUTTON INSTRUCTION

18 | KICHLER.COM

SENSORLESS DC CONTROL PAIRING PROCEDURES

IMPORTANT: Ceiling fan blades MUST be installed before pairing procedure can begin.

Step 1. Program the wall control and/or the handset control separately. Once the following pairing is successfully done, both the

wall control and the handset control can be used for the fan.

For wall control,

fan branch circuit at the circuit breaker or fuse box. Within 60 seconds of turning on the power, press the “ ” power button to

turn on the wall control (the button will be down), and then press the " " reverse button for 3 to 5 seconds. Light will blink twice.

The remote will now be programmed to your fan and ready for use.

For handset control, restore electricity to the ceiling fan branch circuit at the circuit breaker or fuse box. Within 60 seconds of

turning on the power, press “ ” power button for 3 to 5 seconds. Light will blink twice. The remote will now be programmed to

your fan and ready for use.

IMPORTANT: Do not interrupt the conditioning until the fan comes to a complete stop in approximately 5 minutes. All functions of

the control will be rejected during conditioning.

If

programming is unsuccessful, retry the process starting from step 1 again.

85" GENTRY XL | 19

Fig. 21

Select a location to install the Wall Control System Transmitter and Wall

Plate.

REMEMBER also this should state that the control is not to be mounted

outdoors. You can safely use the transmitter outdoors but it should be

mounted indoors away from excess heat and away from contact with

water or humidity.

Install the wall plate using an existing wall switch outlet box. Make sure

the electrical power is TURNED OFF at the main panel before

continuing.

If your ceiling outlet box has a ground wire (green or bare copper)

connect it to the ground wire from the wall switch and/or the ceiling

mounting bracket and push back inside the outlet box.

Install the wall plate on the existing wall outlet box using the screws

provided. (Fig. 21)

After installing the wall anchors, attached the wall plate with the

mounting screws to finish the installation.

INSTALLING THE WALL CONTROL

SYSTEM WALL PLATE

Screws

Outlet box

Screws

Wall plate

Switch

20 | KICHLER.COM

Fig. 22

Fig. 23

Warm weather - Forward (counter clockwise) A downward airflow

creates a cooling effect as shown in Fig. 22. This allows you to set your

air conditioner on a warmer setting without affecting your comfort.

Cool weather - Reverse (clockwise) An upward airflow moves warm air

off the ceiling area as shown in Fig. 23. This allows you to set your

heating unit on a cooler setting without affecting your comfort

NOTE: To change the airflow direction of your ceiling fan use the

FOR/REV button on the wall control transmitter.

OPERATING INSTRUCTIONS

La page charge ...

Kichler 300285WZC Manuel utilisateur

Kichler 300285WZC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents