Polaris PB4SQ Le manuel du propriétaire

Marque: Polaris

Modèle: PB4SQ

Catégorie: Accessoires de piscine hors terre

Taper: Le manuel du propriétaire

FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualied

in pool equipment by the jurisdiction in which the product will be installed, where such state or local requirements

exist. In the event no such state or local requirement exists, the individual in charge of maintenance must be

a professional with sufcient experience in pool equipment installation and maintenance, so that all of the

instructions in this manual can be followed exactly. Improper installation and/or operation can create dangerous

electrical hazards, which can cause high voltages to run through the electrical system. Before installing this

product, read and follow all warning notices and instructions that accompany this product. Failure to follow

warning notices and instructions may result in property damage, personal injury, or death. Improper installation

and/or operation will void the warranty.

If these instructions are not followed exactly, a re or explosion may result, causing property damage, personal

injury, or death.

ATTENTION INSTALLER: This manual contains important information about the installation,

operation and safe use of this product. This information should be given to the owner/operator of

this equipment.

WARNING

H0544300_REVC

Pressure Cleaner Booster Pump

Installation and

Operation Manual

ENGLISH

FRANÇAIS

ESPAÑOL

Page 2

ENGLISH

Polaris® PB4SQ™ Booster Pump | Installation and Operation Manual

Table of Contents

Section 1. IMPORTANT SAFETY INSTRUCTIONS .........3

1.1 Pool Pump Suction Entrapment Prevention Guidelines ...... 4

Section 2. Overview ..........................................................5

2.1 Introduction .......................................................................... 5

2.2 Description .......................................................................... 5

2.3 Dimensions .......................................................................... 5

Section 3. Getting Started ................................................6

3.1 Package Contents ............................................................... 6

3.2 Required Equipment ............................................................ 6

3.2.1 Tools ................................................................................. 6

3.2.2 Materials Supplied by Installer .......................................... 6

Section 4. Installation .......................................................7

4.1 Plumbing Overview ............................................................. 7

4.2 Location Requirements ....................................................... 8

4.3 Electrical Connections ......................................................... 8

4.3.1 Supply Voltage .................................................................. 8

4.3.2 Bonding and Grounding .................................................... 9

4.3.3 Electrical Wiring ................................................................ 9

4.3.4 Connect To Controls ......................................................... 10

4.4 Plumbing Connections ........................................................ 11

Section 5. Operation .........................................................12

5.1 Pressure Test....................................................................... 12

5.2 Start Up ............................................................................... 12

5.3 Maintenance ........................................................................ 13

5.3.1 Winterizing ........................................................................ 13

5.3.2 Troubleshooting and Repair ............................................. 13

Section 6. Replacement Parts .........................................15

DATE OF INSTALLATION

INSTALLER INFORMATION

INITIAL PRESSURE GAUGE READING (WITH CLEAN FILTER)

PUMP MODEL HORSEPOWER

NOTES:

EQUIPMENT INFORMATION RECORD

www.zodiac.com/en/united-states/contact/product-registration

Page 3

ENGLISH

Polaris

PB4SQ™ Booster Pump

Installation and Operation Manual

READ AND FOLLOW ALL INSTRUCTIONS

Section 1. IMPORTANT SAFETY INSTRUCTIONS

All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes.

When installing and using this electrical equipment, basic safety precautions should always be followed, including the

following:

WARNING

In order to reduce the risk of injury, do not permit children to use

this product.

To reduce the risk of property damage or injury, do not attempt to

change the backwash (multiport, slide, or full ow) valve position

with the pump running.

Polaris pumps are powered by a high voltage electric motor and

must be installed by a licensed or certied electrician or a qualied

swimming pool service technician.

WARNING

RISK OF ELECTRIC SHOCK, FIRE, PERSONAL INJURY,

OR DEATH. Connect only to a branch circuit that is protected

by a ground-fault circuit-interrupter (GFCI). Contact a qualied

electrician if you cannot verify that the circuit is protected by a

GFCI. Make sure such a GFCI should be provided by the installer

and should be tested on a routine basis. To test the GFCI, push

the test button. The GFCI should interrupt power. Push the reset

button. Power should be restored. If the GFCI fails to operate in

this manner, the GFCI is defective. If the GFCI interrupts power to

the pump without the test button being pushed, a ground current is

owing, indicating the possibility of electrical shock. Do not use the

pump. Disconnect the pump and have the problem corrected by a

qualied service representative before using.

Due to the potential risk of re, electric shock, or injuries to

persons, Polaris Pumps must be installed in accordance with the

National Electrical Code

(NEC

), all local electrical and safety

codes, and the Occupational Safety and Health Act (OSHA

Copies of the NEC may be ordered from the National Fire

Protection Association

(NFPA

) online at www.nfpa.org or call

617-770-3000, or contact your local government inspection agency.

Incorrectly installed equipment may fail, causing severe injury or

property damage.

WARNING

• Do not connect the system to an unregulated city water

system or other external source of pressurized water producing

pressures greater than 35 PSI.

• Incorrectly installed equipment may fail, causing severe injury

or property damage.

• Trapped air in system can cause the lter lid to be blown

off, which can result in death, serious personal injury, or property

damage. Be sure all air is out of the system before operating.

To minimize the risk of severe injury or death, the lter and/or pump

should not be subjected to the piping system pressurization test.

Local codes may require the pool piping system to be subjected to

a pressure test. These requirements are generally not intended to

apply to the pool equipment such as lters or pumps.

Polaris pool equipment is pressure tested at the factory.

However, if the WARNING cannot be followed and pressure testing

of the piping system must include the lter and/or pump, BE SURE

TO COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS:

Check all clamps, bolts, lids, lock rings and system accessories to

ensure they are properly installed and secured before testing.

RELEASE ALL AIR in the system before testing.

Water pressure for test must NOT EXCEED 35 PSI.

Water temperature for test must NOT EXCEED 100°F (38°C).

Limit test to 24 hours. After test, visually check system to be sure it

is ready for operation.

NOTICE: These parameters apply to Polaris equipment only. For

non-Polaris equipment, consult equipment manufacturer.

Chemical spills and fumes can weaken pool/spa equipment.

Corrosion can cause lters and other equipment to fail, resulting in

severe injury or property damage. Do not store pool chemicals near

your equipment.

CAUTION

Do not start pump dry! Running the pump dry for any length of time

will cause severe damage and will void the warranty.

This pump is for use with permanently installed pools and may

also be used with hot tubs and spas if so marked. Do not use

with storable pools. A permanently installed pool is constructed

in or on the ground or in a building such that it cannot be readily

disassembled for storage. A storable pool is constructed so that it

may be readily disassembled for storage and reassembled to its

original integrity.

Do not install within an outdoor enclosure or beneath the skirt of

a hot tub or portable spa. The pump requires adequate ventilation

to maintain air temperature at less than the maximum ambient

temperature rating listed on the motor rating plate.

SAVE THESE INSTRUCTIONS

Page 4

ENGLISH

Polaris® PB4SQ™ Booster Pump | Installation and Operation Manual

1.1 Pool Pump Suction Entrapment Prevention Guidelines

WARNING

Pump suction is hazardous and can trap and drown or

disembowel bathers. Do not use or operate swimming pools,

spa, or hot tubs if a suction outlet cover is missing, broken,

or loose. The following guidelines provide information for pump

installation that minimizes the risk of injury to users of pools, spas,

and hot tubs:

Entrapment Protection - The pump suction system must provide

protection against the hazards of suction entrapment.

Suction Outlet Covers - All suction outlets must have correctly

installed, screw-fastened covers in place. All suction outlet (drain)

covers must be maintained. Drain covers must be listed/certied

to the latest version of ANSI

/ASME

A112.19.8 or its successor

standard, ANSI/APSP-16. They must be replaced if cracked,

broken, or missing.

Number of Suction Outlets Per Pump - Provide at least two (2)

hydraulically-balanced main drains, with covers, as suction outlets

for each circulating pump suction line. The centers of the main

drains (suction outlets) on any one (1) suction line must be at least

three (3) feet apart, center to center. See Figure 1.

The system must be built to include at least two (2) suction outlets

(drains) connected to the pump whenever the pump is running.

However, if two (2) main drains run into a single suction line, the

single suction line may be equipped with a valve that will shut off

both main drains from the pump. The system shall be constructed

such that it shall not allow for separate or independent shutoff or

isolation of each drain. See Figure 1.

More than one (1) pump can be connected to a single suction line as

long as the requirements above are met.

Water Velocity - The maximum water velocity through the suction

tting or cover for any suction outlet must be 1.5 feet per second

unless the outlet complies with the latest version of ANSI/ASME

A112.19.8 or its successor standard, ANSI/APSP-16, the standard

for Suction Fittings For Use in Swimming Pools, Wading Pools,

Spas, and Hot Tubs. In any case, do not exceed the suction tting’s

maximum designed ow rate.

If 100% of the pump’s ow comes from the main drain system,

the maximum water velocity in the pump suction hydraulic system

must be six (6) feet per second or less, even if one (1) main

drain (suction outlet) is completely blocked. The ow through the

remaining main drain(s) must comply with the latest version of

ANSI/ASME A112.19.8 or its successor standard, ANSI/APSP-

16, the standard for Suction Fittings For Use in Swimming Pools,

Wading Pools, Spas, and Hot Tubs.

Testing and Certication - Suction outlet covers must have been

tested by a nationally recognized testing laboratory and found

to comply with the latest version of ANSI/ASME A112.19.8 or its

successor standard, ANSI/APSP-16, the standard for Suction

Fittings For Use in Swimming Pools, Wading Pools, Spas, and Hot

Tubs.

Fittings - Fittings restrict ow; for best efciency use fewest

possible ttings (but at least two (2) suction outlets).

Avoid ttings which could cause an air trap.

Pool cleaner suction ttings must conform to applicable

International Association of Plumbing and Mechanical Ofcials

(IAPMO

) standards.

Listed/certified to the latest

published version of

ANSI/ASME A112.19.8 or

its successor standard,

ANSI/APSP-16.

Anti-entrapment

Cover/Grate or Suction

Fitting, securely-fastened

to Main Drain Sump

Listed/certified to the latest

published version of

ANSI

/ASME

A112.19.8 or

its successor standard,

ANSI/APSP-16.

Anti-entrapment

Cover/Grate or Suction

Fitting, securely fastened to

Main Drain Sump

At Least

3 Feet

Suction Outlet

(Main Drain)

Suction Outlet

(Main Drain)

Valves permitted only after tee

Pump

No valves between

Tee and Main Drains

Skimmer

Figure 1. Number of Suction Outlets Per Pump

Page 5

ENGLISH

Polaris

PB4SQ™ Booster Pump

Installation and Operation Manual

Section 2. Overview

2.1 INTRODUCTION

This manual contains information for the proper

installation, operation and maintenance of the Polaris

PB4SQ booster pump.

Running the booster pump without a ltration pump

will damage the booster pump. Improper operation

of the booster pump will void the warranty.

CAUTION

2.2 Description

The Polaris PB4SQ Booster Pump,

supplies high pressure water for the

operation of pressure driven pool

cleaners. The PB4SQ is a multistage

booster pump. Hydraulic efciency is

optimized by passing water through

four pressurization stages. At each

stage, water is moved through an

individual impeller and diffuser,

progressively increasing outlet

pressure without increasing motor

Revolutions Per Minute (RPM). This

allows a pressure operated cleaner

to run with optimal power while

minimizing energy consumption. The

pump is not self priming and should

only be used when the pool ltration

pump is on

2.3 Dimensions

16 3/16" (411 mm)

9 7/16"

(240 mm)

(102 mm)

13 5/8" (346 mm)

16 3/16" (411 mm)

7 1/2" (191 mm)

6 3/8" (162 mm)

Anchor bolt hole centers

9 7/16"

(240 mm)

(102 mm)

13 5/8" (346 mm)

Impeller

Diffuser

Outlet

Inlet

Stage 4

Stage 3

Stage 2

Stage 1

Electric Motor

Page 6

ENGLISH

Polaris® PB4SQ™ Booster Pump | Installation and Operation Manual

Section 3. Getting Started

3.1 Package Contents

Before starting, check that you have the correct parts as

indicated below. If any parts are missing or incorrect,

please call your local distributor or technical support at

1-800-822-7933 for assistance.

Item Description Qty.

1 Polaris PB4SQ Booster Pump 1

2 Polaris Quick Connecter Assembly (Barb & Nut) 4

3 Reinforced Hose (6' / 183 cm) 1

3.2 Required Equipment

Please ensure that the following equipment is available to the installer at the time of installation.

3.2.1 Tools

Safety Eyewear Gloves

Phillips Screw-

driver

Flat Head

Screwdriver

Hose Cutters

Channel Locks Tape Measure Voltage Meter

Adjustable

Wrench

PTFE (Teon™)

Tape

3.2.2 Materials Supplied by Installer

Please ensure that all materials used during the

installation are in accordance with local codes or the

authority having jurisdiction (AHJ) requirements. If you

have any questions regarding the materials that need to be

used during this installation please call technical support

at 1-800-822-7933.

NOTE: Required materials may differ from the materials listed. Be

sure to conrm with all local and national codes before beginning

the installation.

ELECTRICAL

SUPPLIES

PLUMBING SUPPLIES

230 VAC

115 VAC

PVC Reducer Bushing (2" - 3/4" NPT)

Flexible Conduit PTFE (Teon™) Tape

Page 7

ENGLISH

Polaris

PB4SQ™ Booster Pump

Installation and Operation Manual

Section 4. Installation

4.1 Plumbing Overview

• The pump must be installed on the outlet side of the lter.

• If installed on a dual equipment system with a heater,

introduce the booster pump downstream no less than

3' feet (1 m). This ensures that excessively heated

water is not passed through the booster pump.

• If using solar heat, ensure that the booster is

equipped with an automatic override to shut off the

pump. This ensures that the pump will not operate in

a no ow condition during solar panel purges.

• Plumb the booster pump upstream from any

chlorination or other sanitation systems.

• Always use properly sized valves. Jandy

Pro Series

valves are recommended for best ow capabilities.

• Use the fewest ttings possible.

NOTE: If more than 10 suction fittings are needed, the

pipe size must be increased.

• The piping must be well supported and not forced

together where constant stress will be experienced.

• A dedicated return line is required.

Filter

Heater

From Skimmer

Variable Speed Pump

Salt Water Chlorination Cell

Check Valve

PB4SQ Booster Pump

For Single Body

Equipment Installations

For Dual Body

Equipment Installations

Filter

Heater

Variable Speed Pump

Check Valve

Salt Water Chlorination Cell

To Pool

From Pool Drain

To Dedicated

Cleaner Return Line

PB4SQ Booster Pump

To Dedicated

Cleaner Return Line

To Spa

To Pool

Figure 2. Typical Equipment Layout

Page 8

ENGLISH

Polaris® PB4SQ™ Booster Pump | Installation and Operation Manual

4.2 Location Requirements

• Pump must receive constant ow from the lter

pump. The PB4SQ is not a self priming pump.

See Figure 2.

PB4SQ Booster Pump

Quick Connect Assembly

Reinforced Hose

5' (1.5 m) min.

From Inner Pool Wall

10' (3 m) min. in Canada

Provide

adequate

clearance for

intake air.

Minimum 3” is

recommended

• A dedicated return line is required.

• DO NOT USE flexible tubing of any kind for an underground return line.

• Plumb upstream of all air inducing equipment.

• Install on a solid level surface that will not vibrate.

• A concrete slab/equipment pad is recommended.

• To reduce noise bolt the pump to the concret equipment pad.

• Ensure the equipment pad has sufficient drainage

1 1/2" (40 mm) PVC min.

1' (30.5 cm) min.

Above Pool

Water Level

Must maintain

constant flow

from filter pump

Min Ø

12” (304.8mm)

To Cleaner

Expansion Anchor

Figure 3. Location Requirements

Some Safety Vacuum Release System (SVRS)

devices are not compatible with the installation of

check valves. If the pool is equipped with an SVRS

device, be sure to conrm that it will continue to

safely operate when check valves are installed.

WARNING

NOTE: For installations in Canada the distance from the inner

pool edge must be 10' (3 m).

• The pump along with all other circulation

equipment must be installed at least 5' (1.5 m) from

the inner pool edge. See Figure 3.

• The pump must be placed on a solid foundation that

will not vibrate. See Figure 3.

• Install the pump as close to the pool as possible and

in a position that will minimize bends in the piping.

• Secure the pump by bolting it to the equipment pad.

This will also have the added benet of helping to

reduce vibration noise. See Figure 3.

• The booster pump inlet connection line should be at

least 3/4” pipe.

• To help prevent difculty in priming, install the

inlet line without high points

or air locks.

• The Quick Connect ttings

are designed to work with the

Polaris reinforced hose (part

#P19). See Figure 8

• Return line should be

rigid PVC at 1 1/2" (40 mm)

Minimum. See Figure 3

• Plumb return line upstream

of any air inducing equipment.

• Install the booster pump

within 1' (30.5 cm) of the pool

water surface. See Figure 3

• The pump should not be

elevated more than a few feet

above the water level of the pool.

• If the pump is installed below the water level,

check valves must be installed on both the inlet and

return lines to prevent back ow during service or

maintenance of the pump.

• The equipment pad must have adequate drainage to

prevent water intrusion to the pump.

• The pump needs to be protected from extreme

weather exposure.

• Proper ventilation is required in order to avoid

excess heat buildup at the pump motor.

• Ensure that sufcient service and maintenance

clearances are provided.

• The area around the pump should be clear and free

of debris.

• Sufcient space must be left above the pump to

allow access to the electrical connections.

• If the equipment is under cover, provide adequate

lighting.

• Do Not Install under the skirt or within the outer

enclosure of a spa.

4.3 Electrical Connections

4.3.1 Supply Voltage

The pump can be wired for supply voltage of either

230VAC or 115VAC. The pump comes factory wired

for 230VAC installation. See section 4.3.3 for details

on wiring the motor for 115VAC supply. Correct

supply voltage is necessary for proper performance and

sustained motor life.

It is the responsibility of the electrical installer to

provide proper operating voltage, based on the pump

motor rating information found here or on the pump

rating plate, ensuring

proper circuit sizes

and wire sizes for this

specic application.

The National Electrical

Code

(NEC

, NFPA-

) requires all

pool pump circuits

be protected with a

MOTOR RATING

MODEL PB4SQ

OUTPUT WATTS 725

HP 0.97

SERVICE FACTOR 1.0

RPM 3450

VOLTS AC

230/115VAC,

1 PHASE,

60 HZ

AMPS 4.5/9.2

DUTY CONT

Page 9

ENGLISH

Polaris

PB4SQ™ Booster Pump

Installation and Operation Manual

Ground Fault Circuit-Interrupter (GFCI). Therefore,

it is also the responsibility of the electrical installer

to ensure that the pump circuit is in compliance

with this and all other applicable requirements of

the National Electrical Code

(NEC

) and any other

applicable installation codes.

Failure to provide data plate voltage (within 10%)

during operation will cause the motor to overheat

and void the warranty.

CAUTION

4.3.2 Bonding and Grounding

The motor frame must be grounded to a reliable

grounding point using a solid copper conductor, No.

8 AWG (8.4mm

) or larger. In Canada, No. 6 AWG

(13.3mm

) or larger must be used. Do not ground to a

gas supply line.

The motor must be bonded to all metal parts of the

swimming pool, spa, or hot tub structure and to all

electrical equipment, metal conduit, and metal piping

within ve (5) feet (1,5 meter) of the inside walls of the

swimming pool, spa, or hot tub. Bond the motor using

the provided external lug.

To avoid the risk of property damage, severe

personal injury, and/or death, always disconnect the

power source before working on a motor or its

connected load.

WARNING

To avoid the risk of property damage, severe personal

injury, and/or death, make sure that the control switch

or time clock is installed in an accessible location so

that in the event of an equipment failure or a loose

plumbing tting the equipment can be turned off. This

location must not be in the same area as the pool

pump, lter, and other equipment.

WARNING

The pump must be permanently connected to a

dedicated electrical circuit. No other equipment,

lights, appliances or outlets may be connected to

the pump circuit, with the exception of devices that

may be required to operate simultaneously with the

pump, such as a chlorinating device or heater.

CAUTION

4.3.3 Electrical Wiring

MAXIMUM WIRE SIZE AND MAXIMUM OVERCURRENT PROTECTION*

Distance from Sub-Panel 0-50 feet (15 meters) 50-100 feet (15-30 meters) 100-200 feet (30-60 meters)

Pump

Model

Branch Fuse AMPs

Class: CC, G, H, J, K, RK, or T

Voltage Voltage Voltage

230 VAC 115 VAC 208-230 VAC 115 VAC 208-230 VAC 115 VAC 208-230 VAC 115 VAC

PB4SQ 15A 15A

14 AWG

(2.1mm

)

12 AWG

(3.3mm

)

12 AWG

(3.3mm

)

10 AWG

(5.3mm

)

10 AWG

(5.3mm

)

10 AWG

(5.3mm

)

*Assumes three (3) copper conductors in a buried conduit and 3% maximum voltage loss in branch circuit. All National Electrical Code

(NEC

) and

local codes must be followed. Table shows minimum wire size and branch fuse recommendations for a typical installation per NEC.

1. Turn off all electrical power at the breakers.

2. Ensure that the pump is installed and rmly attached to

a solid foundation. See Figure 3.

3. Use exible conduit to route supply power lines

to pump location.

4. Determine the best conduit port to use. There is one on

the side and one in the back of the capacitor housing.

5. Loosen do not remove the 4 screws securing the

electrical housing cover to the pump body. See Figure 4.

6. Remove the electrical housing cover and seal assembly.

7. Inspect the cover and seal for any damage or improper

seating. Replace if necessary.

Inlet

Conduit Connection Port

Return

Seal

Cover

Capacitor

Housing

Conduit hubs suitable for wet locations that comply

with the requirements in the Standard for Conduit,

Tubing, and Cable Fittings, UL 514B, are to be used.

Figure 4. Removing Electrical Access Cover

Be careful not to overtighten any conduit tting.

Overtightening can cause the housing to crack.

CAUTION

Page 10

ENGLISH

Polaris® PB4SQ™ Booster Pump | Installation and Operation Manual

A. Factory Wiring for 230VAC Supply

JUMPER

GND

Wiring for

230VAC 60hz

Factory wiring 230VAC

- White Wire in 8 & 9

- Yellow Wire in 7

Figure 5. Factory Wiring For 230VAC

The pump is factory wired for 230VAC supply power.

For 230VAC installations, do not make any adjustments

to the motor's factory wired terminal connections.

For use only with exible wiring systems. Be careful

not to damage or abrade any of the wiring during this

procedure.

1. Remove plug from conduit connection port. See Figure 4.

2. Feed supply wires through conduit connection port.

3. Wire electrical supply according to Figure 5.

4. Secure conduit to the connection port with a 1/2" conduit

elbow or comparable conduit connection. See Figure 5.

Be careful not to damage or abrade any of the wiring.

5. Secure the electrical housing cover using 4 screws.

See Figure 4.

B. Wiring for 115VAC Supply

JUMPER

GND

Wiring For

115VAC 60hz

To change to 115VAC

- Move White Wire

from 9 to 10

- Move Yellow Wire

from 7 to 9

Figure 6. Wiring For 115VAC

The pump is factory wired for 230VAC supply power.

Adjustments to the pump wiring are required in order

to accommodate this supply voltage. For use only with

exible wiring systems. Be careful not to damage or

abrade any of the wiring during this procedure.

1. Remove plug from conduit connection port. See Figure 4.

2. Feed supply wires through conduit port.

3. Rewire factory wiring and wire supply according to

Figure 6.

4. Secure exible conduit to conduit connection port with

a 1/2" conduit elbow or comparable conduit connection.

See Figure 6. Be careful not to damage or abrade any of

the wiring.

5. Secure the electrical housing cover using 4 screws.

See Figure 4.

4.3.4 Connect To Controls

The pump must be connected to a control so that:

• The ltration pump is operating at all times the

booster pump is operating.

• The booster pump is set to run after the lter pump

has been running for 30 minutes, and that it shuts off

30 minutes prior to the lter pump turning off.

• When using Jandy

automation, wire the booster

pump on the Aux 1 relay, and set the DIP switch S1-1

to on. The default label for this preset is "Cleaner"

and operating the booster pump on this relay under

this DIP switch setting will ensure that the lter pump

will work in coordination with the booster pump.

Please review all wiring and programming information

in the controls manual to ensure accurate control and

coordination between the lter pump and booster pump

settings.

Page 11

ENGLISH

Polaris

PB4SQ™ Booster Pump

Installation and Operation Manual

4.4 Plumbing Connections

1. Disconnect power to the ltration system at the breaker.

2. Install a 2" PVC tee downstream from the lter and

upstream from any sanitation or chlorination equipment.

See Figure 7.

3. Connect one leg of the tee to the pool return line.

4. On the open leg of the tee install a PVC 2" to 3/4"

NPT reducer bushing. Be sure to use approved PVC

cement. DO NOT INSTALL with open leg facing up.

See Figure 7.

The pump is not self priming and must be lled

with water from an upstream lter pump. Never

run the booster pump without water. Running the

pump “dry” for any length of time can cause severe

damage to both the pump and motor and will void

the warranty

CAUTION

PVC cement and primer can produce vapors that

can be hazardous to your health. Use PVC cement

to join pipes only in a well ventilated area where

vapors cannot accumulate.

Pipe dope should NEVER be used on barb threads.

Pipe dope will severely weaken the plastic, causing

leakage and may cause the plastic to fracture. DO

NOT OVERTIGHTEN

WARNING

Callout

Description

Reinforced Hose

Quick Connect Nut

Quick Connect

Barbed Fitting

2" - 3/4" NPT

Reducer Bushing

2" PVC Tee

Figure 7. Plumbing Transition Components

5. Apply 4-6 wraps of PTFE (Teon™) tape to the tapered

threads on all four of the barbed ttings. Be sure to wrap

the tape in the opposite direction that the male threads will

be turning in order to create a water tight seal. See Figure 9.

6. Install the quick connect barbed tting into the

reducer bushing.

7. Cut the reinforced hose to length. Make sure the cut is

square and clean.

8. Slide the quick connect nut over the reinforced hose.

See Figure 9.

9. Use water to lubricate the barbs. See Figure 9.

10. Slide the hose over the barbs until a snug t is achieved.

See Figure 8.

11. Tighten the quick connect nuts onto the barbed connector

hand tight only. DO NOT OVERTIGHTEN.

12. Install a second quick connect barbed tting at the pump

suction inlet. See Figure 9.

13. Repeat steps 6-11 to install the reinforced hose

at the pump inlet.

14. Install the third quick connect barbed tting

at the pump outlet.

15. Repeat steps 6-11 to install the reinforced hose

at the pump outlet.

Barb Face

Connector Nut

Connector

Barb

Reinforced

Hose

Nut Gap

Figure 8. Quick Connect Fitting

PTFE (Teflon™)

Tape

Pump Inlet

Quick Connect Nut

Quick Connect Barbed Fitting

Reinforced Hose

Figure 9. Quick Connect Installation

Be careful not to overtighten any pipe tting on the

inlet or outlet of the booster pump. Overtightening

can cause the housing to crack.

CAUTION

16. Run the Reinforced hose to the dedicated return line.

17. Make sure the dedicated return line has a

female 3/4" NPT tting.

18. Install the fourth quick connect barbed tting at the

dedicated return line.

19. Repeat steps 6-11 to install the reinforced hose at the

dedicated return line.

Page 12

ENGLISH

Polaris® PB4SQ™ Booster Pump | Installation and Operation Manual

Section 5. Operation

5.1 Pressure Test

1. Fill the system with water, using care to eliminate

trapped air.

2. Pressurize the system with water to no more than 35 PSI.

3. Close the valve to trap pressurized water in the system.

4. Observe the system for leaks and/or pressure decay.

5. For technical support please call 1-800-822-7933.

When pressure testing a system with water, air

is often trapped in the system during the lling

process. This air will compress when the system is

pressurized. Should the system fail, this trapped air

can propel debris at a high speed and cause injury.

Every effort to remove trapped air must be taken,

including opening the bleed valve on the lter and

loosening the pump basket lid on the lter pump

while lling the pump.

WARNING

Trapped air in system can cause lter lid to be

blown off, which can result in death, serious

personal injury, or property damage. Be sure all air

is properly out of system before operating. DO NOT

USE COMPRESSED AIR TO PRESSURE TEST

OR CHECK FOR LEAKS.

When pressure testing the system with water, it is

very important to make sure that the pump basket

lid on the lter pump is completely secure.

Do not pressure test above 35 PSI. Pressure

testing must be done by a trained pool professional.

Circulation equipment that is not tested properly can

fail, which could result in severe injury or property

damage.

WARNING

5.2 Start Up

If this is a new pool installation, make sure all piping

is clear of construction debris and has been properly

pressure tested. The lter should be checked for proper

installation, verifying all connections and clamps are

secure according to the manufacturer's recommendations.

To avoid risk of damage or injury, verify that all

power is turned off before starting this procedure.

WARNING

1. Turn ltration pump ON.

2. Open the lter pressure release to relieve the system

pressure until water comes out.

3. If the lter pump is located below the water level of the

pool, opening the lter pressure release valve will prime

the pump with water.

4. Once all the air has left the lter, close the pressure

release valve.

5. Turn on the power to the booster pump.

6. The booster pump should prime. The time it takes to

prime will depend on the elevation and length of pipe

used on the suction supply pipe.

7. If the booster pump does not prime and all the

instructions to this point have been followed, check for a

suction leak.

Never run the booster pump without water. Running

the pump “dry” for any length of time can cause

severe damage to both the pump and motor and will

void the warranty.

CAUTION

Never run the booster pump without the cleaner

connected. Running the pump without the cleaner

connected will cause damage to the pump impeller

and will void the warranty. Using this pump for any

purpose other than running a pressure side pool

cleaner will void the warranty

CAUTION

Page 13

ENGLISH

Polaris

PB4SQ™ Booster Pump

Installation and Operation Manual

5.3 Maintenance

5.3.1 Winterizing

The pump must be protected when freezing

temperatures are expected. Allowing the pump to

freeze will cause severe damage and void the

warranty.

CAUTION

Do not use antifreeze solutions in the pool,

spa, or hot tub systems! Antifreeze is highly toxic

and may damage the circulation system. The only

exception to this is Propylene Glycol. For more

information see your local pool/spa supply store or

contact a qualied swimming pool service company.

CAUTION

1. Drain all water from the pump, system equipment, and

piping.

2. Remove the drain plug. Store the drain plug in a safe

location and reinstall it when the cold weather season is

over. Be mindful of the O-ring. Check for damage and

wear and replace as needed, please see Section 6 for a

complete replacement parts list.

3. Keep the motor covered and dry.

NOTE: Covering the pump with plastic will create condensation,

and this moisture will damage the pump. The best way to protect

your pump is to have a qualied service technician or electrician

properly disconnect the electrical wiring at the switch or junction

box. Once the power is removed, the two (2) quick connect ttings

can be loosened and the pump stored indoors. For safety, and to

prevent entry of contaminants, reinstall all conduit and terminal

box covers.

4. When the system is reopened for operation, make sure all

piping, valves, wiring, and equipment are in accordance

with the manufacturer's recommendations. Pay close

attention to the lter and electrical connections.

5. The pump is not self priming and must be lled with

water from an upstream lter pump.

5.3.2 Troubleshooting and Repair

Call a licensed and qualied service professional to

perform any repairs on the lter/pump system. To locate

a service company, visit www.polarispool.com or contact

technical support at 1-800-822-7933.

Symptom Possible Problem/Solution

Pump won't turn on Ensure that there is power to the pump using a digital multimeter set on AC

voltage. The power supplied to the pump must be within 10% of the nameplate

voltage

Check the pump wiring and compare it to the supply voltage. If the pump is wired

for 115VAC operation and the supply voltage is 230VAC it will damage the motor.

Check the capacitor. If the capacitor is bad replace it and try starting the pump.

Check the drive shaft by inserting a 1/4" hex key through the center opening in

the fan cover. If the drive shaft does not spin with ease, it may be seized and may

need to be replaced.

The cleaning/circulating system

is not operating correctly.

Verify that skimmer baskets, pump basket and other screens are clean. Clean as

necessary.

Check filter and clean as necessary.

Check valve positions. Adjust as necessary.

NOTE Multiple pieces of equipment operating at one time (for example,

waterfalls, spa jets, and surface returns) may prevent the cleaning system from

working properly.

Check the cleaning system manually to ensure that the system is adjusted

according to the manufacturer's recommendations.

Bubbles present in the filtration

pump basket.

Air in system. Check the pool or spa water level to ensure it is at the proper level

and that air is not being drawn into the suction piping. If the water is at normal

level, turn off the pump. Remove the lid and check for debris around the lid o-ring

seat or improper installation of the lid seal (these conditions will cause air to leak

into the system). Clean the lid o-ring and replace the lid. Hand-tighten the lid

securely until it reaches the "locked" position (follow instructions on lid). Do not

use any tools to tighten the lid. Turn the pump back on.

Page 14

ENGLISH

Polaris® PB4SQ™ Booster Pump | Installation and Operation Manual

Air leaks are still present. Check the suction side piping union. While the pump is running, try to tighten the

union. If this does not stop the air leak, turn off the pump. Loosen both unions and

slide the pump out of the way. Remove, clean and re-install both union o-rings on

the filtration pump.

Reposition the pump next to the piping and secure the union nuts to the pump.

With clean union o-rings, hand-tightening of the unions should create a seal. If

the unions still do not seal, gently tighten with a large pair of tongue-and-groove

pliers.

Do not over-tighten using a tool. Doing so will compromise the unions.

There is no air in the system,

but the pressure is still low.

It is possible that debris is caught in the pump impeller. The pump impeller moves

the water, and the vanes in the impeller can become blocked with debris.

There is no debris blocking the

impeller and the pressure is still

low.

The pump impeller is showing signs of normal wear. Have a qualified service

technician check the impeller and replace as necessary.

Make sure that the first stage O ring is properly installed and is not pinched or

damaged.

If the pump is part of a relatively new installation, it could be an electrical problem.

Contact a qualified service technician. Have the technician check for loose

electrical connections and check the voltage at the pump motor while it is in

operation. The voltage must be within 10% of the motor's data plate rating. If the

voltage is not within 10%, contact a qualified electrician and/or the local power

service provider.

Pump seal is leaking air. Have a qualified service technician replace the seal.

The pump is leaking water

between the motor and pump

body.

This is caused by a damaged or failed mechanical seal. Replace the seal.

The pump gets hot and shuts

off periodically.

Ensure that there is adequate room around the motor to circulate air and keep the

motor cool. Have a qualified electrician check for loose connections and check the

voltage at the pump motor while it is in operation. The voltage must be within 10%

of the motor's data plate rating. If the voltage is not within 10%, contact a qualified

electrician and/or the local power service provider.

Page 15

ENGLISH

Polaris

PB4SQ™ Booster Pump

Installation and Operation Manual

13,15

3,4,5

3,4

1,3

2,3

13, 14 (4 ea)

7,8,9

8,9,10

12 (4 ea)

9,10

1,3 (4 ea)

Section 6. Replacement Parts

ITEM Part # Description

R0722900 Capacitor Housing Cover

R0734500 Capacitor 30MFD 400V

R0734200 Motor Kit

R0722600 Fan Cover

R0723000 Motor Fan

R0722700 Base

R0747800 Mechanical Seal

ITEM Part # Description

R0723200 Backplate Kit

R0734300 Seal Replacement Kit

R0723100 Pump Body

R0722800 Impeller and Diffuser Kit

R0734400 Pump Hardware Kit

R0617100 Quick Connect Install Kit

R0621000 Quick Connect Set

P19 Reinforced Hose 6 ft.

ZODIAC

is a registered trademark of Zodiac International, S.A.S.U., used under license.

Polaris® and the Polaris 3-wheeled cleaner design are

registered trademarks of Zodiac Pool Systems, Inc.

All trademarks referenced herein are the property of their respective owners.

Zodiac Pool Systems Canada, Inc.

2115 South Service Road West, Unit 3

Oakville, ON L6L 5W2

1.800.822.7933 | www.ZodiacPoolSystems.ca

CONFORMS TO UL 1081

CERTIFIED TO CSA C22.2 NO 108

Zodiac Pool Systems, Inc.

2620 Commerce Way, Vista, CA 92081

1.800.822.7933 | www.polarispool.com

POUR VOTRE SÉCURITÉ – Ce produit doit être installé et entretenu par un entrepreneur autorisé et qualié

pour les équipements de piscine par la juridiction dans laquelle le produit sera installé lorsque de telles exigences

locales ou gouvernementales existent. Si aucune exigence locale ou gouvernementale n'existe, l'individu

responsable de la maintenance doit être un professionnel possédant sufsamment d'expérience dans l'installation

et la maintenance des équipements de piscine pour suivre correctement les consignes du présent manuel. Une

installation et/ou une utilisation incorrectes peuvent causer de dangereux risques électriques pouvant provoquer

le passage de courants haute tension dans le système électrique. Avant d'installer ce produit, lisez et respectez

la totalité des avertissements et instructions qui accompagnent ce produit. Le non-respect des avertissements et

des instructions peut entraîner des dommages matériels, des blessures ou même la mort. Une installation et/ou

une utilisation inappropriées annuleront la garantie.

Si ces instructions ne sont pas suivies à la lettre, un incendie ou une explosion pourrait survenir et causer des

dommages à la propriété, des blessures ou la mort.

NOTE POUR L'INSTALLATEUR : Ce manuel contient des informations importantes concernant

l'installation, le fonctionnement et l'utilisation sans risque de ce produit. Ces informations doivent

être données au propriétaire/à l'utilisateur de cet équipement.

AVERTISSEMENT

H0544300_REVC

Pompe de surpression pour

nettoyeur à pression

Manuel d'installation et

mode d'emploi

ENGLISH

FRANÇAIS

ESPAÑOL

Page 18

FRANÇAIS

Polaris

Pompe de surpression PB4SQ™ | Manuel d'installation et mode d'emploi

Table des matières

CONSIGNES DE SÉCURITÉ IMPORTANTES .................... 19

Directives de prévention du piégeage

par aspiration de la pompe de piscine ........................................... 20

Vue d'ensemble ................................................ 21

INTRODUCTION ........................................................................... 21

Description..................................................................................... 21

Dimensions .................................................................................... 21

Pour commencer .............................................. 22

Contenu de l'emballage ................................................................. 22

Équipements requis ....................................................................... 22

Outils .......................................................................................... 22

Matériaux fournis par l'installateur .............................................. 22

Installation ..........................................................................23

Vue d'ensemble de la plomberie ................................................... 23

Exigences d'emplacement ............................................................. 24

Raccordements électriques ........................................................... 24

Tension d'alimentation................................................................. 24

Liaison électrique et mise à la terre ............................................ 25

Câblage électrique ...................................................................... 25

Raccordement aux commandes ................................................. 26

Raccords de plomberie.................................................................. 27

Fonctionnement ..................................................................28

Essai de pression .......................................................................... 28

Démarrage..................................................................................... 28

Maintenance .................................................................................. 29

Hivérisation ................................................................................. 29

Dépannage et réparation ............................................................ 29

Pièces de rechange ............................................................31

DATE D'INSTALLATION

INFORMATIONS DE L'INSTALLATEUR

LECTURE INITIALE DU MANOMÈTRE (AVEC FILTRE PROPRE)

MODÈLE DE POMPE CHEVAUX-VAPEUR

REMARQUES :

FICHE D'INFORMATIONS SUR L'ÉQUIPEMENT

ENREGISTREZ VOTRE PRODUIT EN LIGNE :

www.zodiac.com/en/united-states/contact/product-registration

Page 19

FRANÇAIS

Polaris

Pompe de surpression PB4SQ™

Manuel d'installation et mode d'emploi

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS

Section 1. CONSIGNES DE SÉCURITÉ IMPORTANTES

Tous les travaux électriques doivent être effectués par un électricien agréé et doivent être conformes aux normes

fédérales, provinciales et locales. Lorsque vous installez et utilisez cet équipement électrique, des mesures de sécurité

de base doivent toujours être prises, en particulier les mesures suivantes :

AVERTISSEMENT

Pour réduire le risque de blessure, ne laissez pas les enfants

utiliser ce produit.

Pour réduire le risque de dommage matériel ou de blessure, ne

tentez pas de changer la position de la valve de lavage à contre-

courant (multivoies, glissement ou débit intégral) pendant le

fonctionnement de la pompe.

Les pompes Polaris fonctionnent à l'aide d'un moteur électrique

haute tension et doivent être installées par un électricien certié

ou autorisé, ou un technicien qualié en entretien et en réparation

de piscines.

AVERTISSEMENT

RISQUE DE CHOC ÉLECTRIQUE, D'INCENDIE, DE

BLESSURES OU DE MORT. Branchez l'appareil uniquement à un

circuit qui est protégé par un disjoncteur de fuite de terre (DDFT).

Communiquez avec un électricien qualié si vous ne pouvez pas

conrmer que le circuit est protégé par un disjoncteur de fuite de

terre. Assurez-vous que ce disjoncteur de fuite de terre soit fourni

par l'installateur et testé régulièrement. Pour tester le disjoncteur

de fuite de terre, appuyez sur le bouton de test. Le disjoncteur de

fuite de terre doit interrompre l'alimentation électrique. Appuyez

sur le bouton de réinitialisation. L'alimentation électrique devrait

être rétablie. Si le disjoncteur de fuite de terre ne fonctionne pas

de cette façon, le disjoncteur est défectueux. Si le disjoncteur

de fuite de terre interrompt l'alimentation de la pompe sans que

vous enfonciez le bouton de test, cela signie qu'un courant à la

terre circule et qu'un choc électrique est possible. N'utilisez pas la

pompe. Débranchez la pompe, puis faites corriger le problème par

un représentant d'entretien qualié avant de l'utiliser.

En raison du risque potentiel d'incendie, de choc électrique ou de

blessures corporelles, les pompes Polaris doivent être installées

conformément au code électrique national (National Electrical

Code

– NEC

), à tous les codes d'électricité et de sécurité locaux,

ainsi qu'à la Loi de sécurité et de salubrité du travail (OSHA

Vous pouvez obtenir des exemplaires du code électrique national

de l'association nationale de protection contre l'incendie (National

Fire Protection Association

– NFPA

) en ligne au www.nfpa.org ou

en composant le 617-770-3000 ou en communiquant avec votre

organisme d'inspection gouvernemental local.

Un équipement installé incorrectement peut être défaillant et

causer des blessures graves ou des dommages matériels.

AVERTISSEMENT

• Ne raccordez pas le système à un système d'alimentation en

eau urbain non règlementé ou à une autre source externe d'eau

sous pression générant des pressions supérieures à 35 psi.

• Un équipement installé incorrectement peut être défaillant et

causer des blessures graves ou des dommages matériels.

• L'air emprisonné dans le système risque de provoquer une

ouverture explosive du couvercle du ltre, ce qui peut entraîner

la mort, des blessures graves ou des dommages matériels. Avant

d'utiliser le système, assurez-vous que tout l'air soit expulsé.

Pour réduire les risques de blessures graves ou mortelles, le ltre

et/ou la pompe ne doivent pas être soumis à l'essai de mise sous

pression du système de tuyauterie.

Les codes locaux peuvent exiger un essai de mise sous pression

du système de tuyauterie de la piscine. Ces exigences ne

s'appliquent généralement pas aux équipements de piscine tels

que les ltres ou les pompes.

L'équipement de piscine Polaris a fait l'objet d'un essai de mise

sous pression en usine.

Toutefois, si l'AVERTISSEMENT ne peut pas être respecté et que

l'essai de mise sous pression du système de tuyauterie doit inclure

le ltre et/ou la pompe, ASSUREZ-VOUS DE VOUS CONFORMER

AUX CONSIGNES DE SÉCURITÉ SUIVANTES :

Vériez que l'ensemble des brides, boulons, couvercles, bagues de

retenue et accessoires du système sont correctement installés et

xés avant d'effectuer un essai.

ÉVACUEZ TOUT L'AIR du système avant d'effectuer un essai.

La pression d'eau pour l'essai ne doit PAS DÉPASSER 35 PSI.

La température de l'eau pour l'essai ne doit PAS DÉPASSER

100 °F (38 °C).

Limitez l'essai à 24 heures. Après l'essai, vériez visuellement le

système pour vous assurer qu'il est prêt à fonctionner.

AVIS : Ces paramètres s'appliquent uniquement à l'équipement

Polaris. Pour un équipement qui n'est pas fabriqué par Polaris,

consultez le fabricant.

Des déversements et vapeurs chimiques peuvent affaiblir

l'équipement de la piscine/du spa. La corrosion risque de

provoquer la défaillance des ltres et autres équipements, ce qui

peut entraîner des blessures graves ou des dommages matériels.

N'entreposez pas de produits chimiques pour piscine à proximité

de votre équipement.

ATTENTION

Ne démarrez pas la pompe à sec! Faire fonctionner la pompe à sec

pendant une durée quelconque causera des dommages importants

et annulera la garantie.

Cette pompe doit être utilisée avec des piscines installées de

manière permanente et, si cela est également mentionné, avec des

cuves thermales et des spas. Ne l'utilisez pas avec des piscines

remisables. Une piscine permanente est construite dans le sol,

sur le sol ou dans un bâtiment et ne peut pas être facilement

démontée et entreposée. Une piscine remisable est conçue pour

être facilement démontée et entreposée, puis remontée dans son

état initial.

Ne l'installez pas dans une enceinte extérieure ou sous les bords

d'une cuve thermale ou d'un spa portatif. La pompe nécessite

une ventilation adéquate an de maintenir la température de l'air

inférieure à la température ambiante maximale indiquée sur la

plaque signalétique du moteur.

CONSERVEZ CES INSTRUCTIONS

Page 20

FRANÇAIS

Polaris

Pompe de surpression PB4SQ™ | Manuel d'installation et mode d'emploi

1.1 Directives de prévention du piégeage par aspiration de la pompe de piscine

AVERTISSEMENT

L'aspiration de la pompe est dangereuse et peut piéger,

noyer ou éviscérer les baigneurs. N'utilisez pas ou ne faites

pas fonctionner de piscines, spas ou cuves thermales si

un couvercle de sortie d'aspiration est manquant, brisé ou

instable. Les directives suivantes fournissent les informations

d'installation de la pompe qui permettent de minimiser les

risques de blessure pour les utilisateurs de piscines, spas et

cuves thermales :

Protection contre le piégeage – Le système d'aspiration de la

pompe doit fournir une protection contre les dangers de piégeage

par aspiration.

Couvercles de sorties d'aspiration – Toutes les sorties

d'aspiration doivent comporter des couvercles correctement

installés et vissés en place. Tous les couvercles de sortie

d'aspiration (drain) doivent être entretenus. Les couvercles de drain

doivent être homologués/certiés conformément à la plus récente

version d'ANSI

/ASME

A112.19.8 ou la norme de remplacement,

ANSI/APSP-16. Ils doivent être remplacés s'ils sont fendus, cassés

ou manquants.

Nombre de sorties d'aspiration par pompe – Prévoyez au

moins deux (2) drains de fond hydrauliquement équilibrés, avec

couvercles, comme sorties d'aspiration pour chaque tuyauterie

d'aspiration de pompe de circulation. Les centres des drains de

fond (sorties d'aspiration) sur une (1) conduite d'aspiration doivent

être éloignés d'au moins trois (3) pieds (91 cm) l'un de l'autre,

entre-axes. Voir la Figure 1.

Le système doit être conçu pour comprendre au moins deux (2)

sorties d'aspiration (drains) raccordées à la pompe chaque fois

que la pompe fonctionne. Toutefois, si deux (2) drains de fond

aboutissent à une seule tuyauterie d'aspiration, cette dernière peut

être équipée d'une valve qui coupera les deux drains de fond de la

pompe. Le système doit être conçu de manière à ne pas permettre

une fermeture ou un isolement distinct ou indépendant de chaque

drain. Voir la Figure 1.

Plus d'une (1) pompe peut être raccordée à une seule tuyauterie

d'aspiration à condition que les exigences susmentionnées soient

respectées.

Vitesse de l'eau – La vitesse maximale de l'eau à travers le

raccord d'aspiration ou le couvercle de toute prise d'aspiration doit

être de 1,5 pi/s (45 cm/s), à moins que la sortie ne soit conforme

à la plus récente version d'ANSI/ASME A112.19.8 ou la norme

de remplacement, ANSI/APSP-16, la norme pour les raccords

d'aspiration à utiliser dans les piscines, pataugeoires, spas et

cuves thermales. Dans tous les cas, ne dépassez pas les débits

maximaux spéciés pour les raccords d'aspiration.

Si 100 % du débit de la pompe provient du système de drain de

fond, la vitesse maximale de l'eau dans le système hydraulique

d'aspiration de la pompe doit être de 6 pi/s (183 cm/s) ou

moins, même lorsqu'un (1) drain de fond (sortie d'aspiration) est

complètement bloqué. Le débit à travers les autres drains de

fond doit être conforme à la plus récente version d'ANSI/ASME

A112.19.8 ou la norme de remplacement, ANSI/APSP-16, la

norme pour les raccords d'aspiration à utiliser dans les piscines,

pataugeoires, spas et cuves thermales.

Essais et certication – Les couvercles de prise d'aspiration

doivent avoir fait l'objet d'essais dans un laboratoire reconnu à

l'échelle nationale et être jugés conformes à la plus récente version

d'ANSI/ASME A112.19.8 ou la norme de remplacement, ANSI/

APSP-16, la norme pour les raccords d'aspiration à utiliser dans les

piscines, les pataugeoires, les spas et les cuves thermales.

Raccords – Les raccords limitent le débit; pour une plus grande

efcacité, utilisez le moins possible de raccords (mais au moins

deux (2) sorties d'aspiration).

Évitez les raccords qui pourraient causer l'emprisonnement de l'air.

Les raccords d'aspiration du nettoyeur de piscine doivent être

conformes aux normes de l'International Association of Plumbing

and Mechanical Ofcials (IAPMO

Homologué/certifié

conformément à la plus

récente version publiée

d'ANSI/ASME A112.19.8 ou

la norme de remplacement,

ANSI/APSP-16.

Couvercle/grille

anti-piégeage ou raccord

d'aspiration, fixé solidement

au puisard de drain de fond

Homologué/certifié

conformément à la plus récente

version publiée

d'ANSI

/ASME

A112.19.8 ou

la norme de remplacement,

ANSI/APSP-16.

Couvercle/grille anti-piégeage

ou raccord d'aspiration, fixé

solidement au puisard de

drain de fond

Au moins

3 pieds

Sortie d'aspiration

(drain de fond)

Sortie d'aspiration

(drain de fond)

Valves permises uniquement

après le raccord en T

Pompe

Aucune valve entre le raccord

en T et les drains de fond

Écumeur

Figure 1. Nombre de sorties d'aspiration par pompe

La page est en cours de chargement...

Polaris PB4SQ Le manuel du propriétaire

Marque: Polaris

Modèle: PB4SQ

Catégorie: Accessoires de piscine hors terre

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Polaris PB4SQ Owner's manual
español: Polaris PB4SQ El manual del propietario

Polaris PB4SQ Le manuel du propriétaire

Polaris PB4SQ Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents