Maytag MFX2570AEB0 User Instructions

Marque: Maytag

Modèle: MFX2570AEB0

Catégorie: Frigos

Taper: User Instructions

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.maytag.com for additional information. If you still need assistance, call us at 1-800-688-9900.

In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de

su producto, visite: www.maytag.com.

Necesitara su nQmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

Table of Contents / Table des mati res

REFRIGERATOR SAFETY ........................................................ 2

Proper Disposal of Your Old Refrigerator .............................. 2

INSTALLATION INSTRUCTIONS ............................................. 3

Unpack the Refrigerator ......................................................... 3

Location Requirements .......................................................... 3

Electrical Requirements .......................................................... 4

Water Supply Requirements................................................... 4

Connect the Water Supply ..................................................... 4

Refrigerator Doors and Drawer .............................................. 6

Adjust the Doors ..................................................................... 9

REFRIGERATOR USE............................................................... 9

Opening and Closing Doors ................................................... 9

Using the Controls .................................................................. 9

Exterior Refrigerator Drawer ................................................. 11

Ice Maker and Ice Storage Bin ............................................. 11

Water and Ice Dispensers ......................................................

Water Filtration System ........................................................ 15

REFRIGERATOR CARE .......................................................... 15

Cleaning ................................................................................ 15

Changing the Light Bulb ....................................................... 16

TROUBLESHOOTING ............................................................. 17

Refrigerator Operation .......................................................... 17

Temperature and Moisture ................................................... 17

Ice and Water ........................................................................ 18

WATER FILTER CERTIFICATIONS ....................................... 19

PERFORMANCE DATA SHEETS ........................................... 20

WAR RANTY ............................................................................. 22

SI_CURITI_ DU RI_FRIGI_RATEUR ......................................... 24

Mise au rebut adequate de votre vieux refrig6rateur ...........25

INSTRUCTIONS D'INSTALLATION ....................................... 25

Deballage du refrig6rateur .................................................... 25

Exigences d'emplacement ................................................... 26

Specifications electriques ..................................................... 26

Specifications de I'alimentation en eau................................ 27

Raccordement de la canalisation d'eau ............................... 27

Portes et tiroir du r6frig6rateur .............................................. 29

Ajustement des portes .......................................................... 32

UTILISATION DU RI_FRIGI_RATEUR .................................... 32

Ouverture et fermeture des portes ....................................... 32

Utilisation des commandes .................................................. 32

Tiroir refrig6r6 externe ........................................................... 35

Machine &gla£;ons et bac d'entreposage ............................ 35

Distributeur d'eau et de gla£:ons .......................................... 35

Systeme de filtration de I'eau ............................................... 38

ENTRETIEN DU RI_FRIGI_RATEUR ....................................... 39

Nettoyage .............................................................................. 39

Remplacement de I'ampoule d'eclairage ............................. 40

DI_PANNAGE ........................................................................... 41

Fonctionnement du refrig6rateur .......................................... 41

-I-emperature et humidite ...................................................... 42

Gla£;ons et eau...................................................................... 42

FEUlLLES DE DONNI_ES SUR LA PERFORMANCE ........... 44

GARANTIE ............................................................................... 46

W10476752A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in "Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/2"

(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. If your refrigerator has an

ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 33/4'' (9.5 cm) minimum space between the refrigerator

and wall to allow the door to swing open.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the

refrigerator in a location where the temperature will fall below

55°F (13°C).

1/2" (1.25 cm) /

I II I

3s/4'' (9.5 cm)

p _

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF, and then disconnect the

refrigerator from the electrical source. When you have finished,

reconnect the refrigerator to the electrical source and turn

Cooling ON. See "Using the Control(s)."

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • _/4"Nut driver

• 7/_e"and Y2"Open-end or two • _/4"Drill bit

adjustable wrenches

• Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/_e"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

• For models with water filters, the disposable water filter

should be replaced at least every 6 months.

Water Pressure

A cold water supply with water pressure of between 35 and

120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

• If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water

Filtration System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

..... iA_i:!I, '°_ _" ' I++,

Read all directions before you begin.

IMPORTANT: Ifyou turn the refrigerator on before the water line

is connected, turn the ice maker OFE

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a V2"to lY4" (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the rear of the refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use Y4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

Using a cordless drill, drill a 1/4"hole in the cold water pipe

you have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E.Compression sleeve

F. Shutoff valve

G.Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

slowly and evenly so the washer makes a watertight seal. Do

not overtighten.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten or

you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove the plastic cap from water supply connection. Place

brass nut and compression sleeve on copper tube end as

shown.

4. Check connection by pulling on the copper tubing.

5. Fasten the plastic water line to the refrigerator with a "P"

clamp. Slide the plastic water line into the retainer.

A. Brass nut C. "P" clamp

B. Compression sleeve

Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

the tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the tubing. Fasten the copper tubing to the

refrigerator cabinet with a "P" clamp.

A. Brass nut

B. Compression sleeve

2. Place end of the copper tubing into the plastic water valve

supply line. Slide the brass nut over the sleeve and screw the

nut into supply line.

3. Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the nut on the copper tubing counterclockwise to completely

tighten. Do not overtighten.

A. Copper tubing

B. "P" clamp

C. Compression nut

D. Compression sleeve

Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispensers."

Ret_i_/io_ __-_ a_ _,_aw_ _

All graphics referenced in the following instructions are included

later in this section after "Final Steps."

Remove and Replace Handles

To Remove Handles:

1. Grasp the lower part of the handle firmly, slide the handle up

and pull the handle straight out from the door. See Handle

graphic.

To Replace Handles:

1. Position the handle so that the large holes in the mounting

clips are down and align the holes with the door studs.

2. Rotate the handle so that the mounting clips are flat against

the door and slide the handle down to engage. See Handle

graphic.

Remove Doors and Hinges

IMPO RTANT:

Remove food and any adjustable door or utility bins from

doors.

Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

TOOLS NEEDED: %e", 3/8",V4"hex head socket wrench, T20®

Torx®tscrewdriver, #2 Phillips screwdriver, and a flat-blade

screwdriver.

1. Unplug refrigerator or disconnect power.

2. Remove the base grille. Grasp the grille firmly and pull it

toward you.

3. Starting with the right-hand side door, remove the parts for

the top hinge as shown in Top Hinge graphic. Lift the

refrigerator door from the bottom hinge pin.

4. Remove the top hinge cover from left-hand side refrigerator

door.

5. Disconnect the wiring plug located on top of the hinge by

wedging a flat-blade screwdriver or your fingernail between

the two sections. See Connections graphic.

6. Disconnect the water line by pulling back on the locking collar

while pulling the water line out of the water line connector.

See Connections graphic.

7. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the left-hand side door from the bottom hinge

pin.

8. Using a 3/8"hex wrench, remove the leveling leg brackets from

the bottom of the cabinet. Keep screws for later use.

t-(_JFORX and T20 are registered trademarl<s of Saturn Fasteners, Inc.

Replace Doors and Hinges

1. Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten the screws completely.

2. Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

3. Align the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

5. Reconnect the water line by pulling back the locking collar

ring while firmly pushing the water line into the connector.

6. Check for leaks. Replace the top hinge covers.

Remove and Replace Refrigerator Drawer and Freezer

Drawer

IMPORTANT: Two people may be required to remove and

replace the freezer drawer. Graphics are included later in this

section.

Remove Drawer Front

1. Open the drawer to full extension.

2. Loosen the two top screws attaching the drawer glide

brackets to the drawer front. See Drawer Front Removal

graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Remove the two bottom screws attaching the drawer glide

brackets to the drawer front.

4. Lift the drawer front up and off the top screws. See Drawer

Front Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the compartment. Insert the

two screws in the drawer front into the upper slots in the

drawer glide brackets. See Drawer Front Replacement

graphic.

2. Align the drawer glide brackets with the lower holes in the

drawer front and refasten with the screws. See Drawer Front

Replacement graphic.

3. Completely tighten the four screws.

Final Steps

1. Replacethe basegrille.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug into a grounded 3 prong outlet.

3. Return all removable parts to doors and drawer and food to

refrigerator and freezer.

Bottom Hinges

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Connections

i !

i I

A. Wiring Plug

B. WaterL_e Connection

B •

A. Loosen 2 Drawer Glide Bracket Screws

B. Remove 2 Drawer Glide Bracket Screws

IMPORTANT:

Your refrigerator has two adjustable, front leveling screws -

one on each side of the refrigerator base. If your refrigerator

seems unsteady or you want the door to close easier, use the

instructions below.

• Before moving the refrigerator, raise the leveling screws so

the front rollers are touching the floor.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Raise or lower the cabinet.

Using a 1/4"hex driver, turn the leveling screw on each side to

raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws. It may take several turns of

the leveling screw to adjust the tilt of the refrigerator.

• To raise, turn the leveling screw clockwise.

• To lower, turn the leveling screw counterclockwise.

A. Leveling screw

Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

REFRIGERATOR USE

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

_,,, _ )_;_ .......... _.....

The refrigerator and freezer controls are located on the dispenser

panel.

IMPORTANT: The display screen on the dispenser control panel

will turn off automatically and enter "sleep" mode when the

control buttons and dispenser levers have not been used for

2 minutes or more. While in "sleep" mode, the first press of a

control button will only reactivate the display screen, without

changing any settings. After reactivation, changes to any settings

can then be made. If no changes are made within 2 minutes, the

display will re-enter "sleep" mode.

• Touchanycontrolbuttononthedispenserpaneltoactivate

thedisplayscreen.Thehomescreenwillappearasshown.

Adjusting the Controls

For your convenience, your refrigerator and freezer controls are

preset at the factory. When you first install your refrigerator, make

sure that the controls are still set to the "mid-settings." The

factory recommended set points are 38°F (3°C) for the

refrigerator and 0°F (-18°C) for the freezer.

IMPORTANT:

• Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the set points to a colder than

recommended setting will not cool the compartments any

faster.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

• The preset temperatures should be correct for normal

household usage. The controls are set correctly when milk or

juice is as cold as you like and when ice cream is firm.

• Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

To view and adjust the set points, press and hold TEMP for

3 seconds. When adjust mode is activated, adjusting information

will appear on the display screen.

• Press LOCK to raise the set point, or press OPTIONS to lower

the set point.

• When you have finished viewing (and adjusting if desired) the

refrigerator set point, press TEMP to change the display to

show the freezer set point. When the zone has been changed,

"FREEZER" appears on the display screen.

• Press LOCK to raise the set point, or press OPTIONS to lower

the set point.

• When you have finished viewing (and adjusting if desired)

both the refrigerator and freezer set points, press

MEASURED FILL "Confirm" to save the settings.

NOTE: To exit without saving changes, press ICE TYPE

"Back" at any time while in adjust mode, or allow about

60 seconds of inactivity and adjust mode will turn off

automatically.

When adjusting temperature set points, use the following chart as

a guide.

CONDITION: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Setting

1° higher

REFRIGERATOR too warm REFRIGERATOR Setting

1° lower

FREEZER too cold FREEZER Setting

1° higher

FREEZER too warm / FREEZER Setting

Too little ice 1° lower

The set point range for the refrigerator is 33°F to 45°F (0°C to

7°C). The set point range for the freezer is -5°F to 5°F (-21 °C to

-15°C).

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is

turned off.

• To turn cooling off, press and hold the LOCK and

MEASURED FILL buttons at the same time for 3 seconds.

IMPORTANT: To avoid unintentionally locking the dispenser

or changing other settings, be sure to press both buttons at

exactly the same time.

When the cooling is turned off, "Cooling Off" will appear on

the display screen as shown.

NOTE: To view Celsius temperatures, press the LIGHT button

when adjust mode is activated. To return the display setting to

Fahrenheit, press LIGHT again.

• When adjust mode is activated, the display screen shows the

refrigerator set point and "FRIDGE" appears.

• Press and hold LOCK and MEASURED FILL for 3 seconds

again to turn cooling back on.

Options

SpeedCool

The SpeedCool feature assists with periods of high refrigerator

use, full grocery loads, or temporarily warm room temperatures.

• Toturn on the SpeedCool feature, press the OPTIONS button

to enter Options mode, then press OPTIONS again to activate

the feature. When the feature is on, "SpeedCool" will appear

on the dispenser display screen. The SpeedCool feature will

remain on for 24 hours unless manually turned off.

• To manually turn off the SpeedCool feature, press the

OPTIONS button to enter Options mode (unless you are

already in Options mode), then press OPTIONS again. When

the feature has been turned off, "SpeedCool" will disappear

on the dispenser display.

NOTE: Setting the freezer to a colder temperature may make

some foods, such as ice cream, harder.

Ice Maker On/Off

You can turn the ice maker ON or OFF from the control panel.

• Press the OPTIONS button to enter Options mode. The words

"Ice Maker" will illuminate. Then press TEMP to toggle

between "Ice Maker" and "Ice Maker Off." When the ice

maker is turned off, "Ice Maker Off" will illuminate.

Additional Features

Sabbath Mode

Sabbath Mode is designed for those whose religious

observances require turning off the lights and dispensers.

In Sabbath Mode, the temperature set points remain unchanged,

but the interior and dispenser lights turn off, all sounds and

alarms are disabled, the dispenser display screen backlight turns

off, and the dispenser levers are disabled. The ice maker is also

disabled; however, "Ice Maker Off" will not appear on the display.

• To turn on Sabbath Mode, press and hold LIGHT and

OPTIONS at the same time for 3 seconds. When the feature

turns on, "Sabbath Mode" will appear on the display.

• To turn off Sabbath Mode, press and hold LIGHT and

OPTIONS at the same time, for 3 seconds, again. The screen

will display the settings as they were before Sabbath Mode

was turned on. The SpeedCool feature, however, will remain

off until it is selected again.

Power Outage Indicator

The power outage indicator lets you know if the power supply to

the refrigerator has been cut off and the freezer temperature has

risen to 18°F (-8°C) or higher.

When power has been restored, "PO" repeatedly flashes on the

display screen and the red Power Outage icon appears.

When the indicator is on, all other control and dispenser

functions are disabled until you confirm that you are aware of the

power outage.

• To enable other functions, press MEASURED FILL to reset

the display screen to its normal status.

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the

refrigerator or freezer door is open for 5 minutes and the product

cooling is turned on. The alarm will repeat every 2 minutes. Close

both doors to turn it off. The feature then resets and will

reactivate when either door is left open again for 5 minutes.

NOTE: To mute the audible alarm while keeping the doors open,

such as while cleaning the inside of the refrigerator, press any

button on the control panel. The alarm sound will be temporarily

turned off, but the Door Ajar icon will still be displayed on the

dispenser control panel.

Disabling Sounds

• To turn off all control and dispenser sounds, press and hold

ICE TYPE and MEASURED FILL at the same time for

3 seconds.

• To turn all sounds back on, press and hold ICE TYPE and

MEASURED FILL at the same time for 3 seconds again.

Water Filter Status Light and Filter Reset

The filter reset control allows you to restart the water filter status

tracking feature each time you replace the water filter. See "Water

Filtration System."

• After changing the water filter, reset the status light. Press the

OPTIONS button to enter Options mode, then press LOCK to

initiate the reset, then press MEASURED FILL to confirm that

you want to reset the status light. When the system is reset,

the "Order" and "Replace" icons will disappear from the

display screen.

The refrigerator drawer holds more fresh food in more ways than

ever before, and is ideal for storing popular food items that need

to be readily accessible. In addition, the drawer's location allows

children to serve themselves from the refrigerator.

Use the full-width drawer to store large party platters or deli trays,

or use a drawer organizer to store smaller items such as yogurt,

juice boxes and lunch meat within easy access.

IMPORTANT:

• Flush the water system before turning on the ice maker. See

"Water and Ice Dispensers."

• The ice maker and storage bin are located in the upper left-

hand side of the refrigerator compartment.

Turning the Ice Maker On/Off

The ice maker has an automatic shutoff. When the ice maker is

on, sensors will automatically stop ice production when the

storage bin is full. The ice maker will remain set to ON, and ice

production will resume when the bin is no longer full.

To manually turn off the ice maker:

Press OPTIONS to display the OPTIONS screen. Pressing ICE

MAKER, if the ice maker is currently on, will turn off the ice maker.

The "Ice Maker Off" icon will flash three times and then stay lit.

When the ice maker is set to OFF, it will stop producing ice.

Pressing ICE MAKER, if the ice maker is currently off, turns on

the ice maker. The "Ice Maker Off" icon will disappear.

Removing and Replacing Ice Storage Bin

To Remove the Ice Storage Bin:

1. Hold the base of the storage bin and press the release

button.

2. Pull out the storage bin.

To Replace the Ice Storage Bin:

IMPORTANT: It may be necessary to turn the auger driver,

behind the ice bin, counterclockwise to properly align the ice bin

with the auger driver. The ice storage bin must be locked in place

for proper ice dispensing.

1. Slide the ice bin into the guide rails located on either side of

the enclosure.

2. Push the ice bin in until resistance is felt. Raise the front

slightly and push the ice bin in until an audible "click" is

heard.

A. Auger driver

Ice Production Rate

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period.

• To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

NOTE: Setting the freezer to a colder temperature may make

some foods, such as ice cream, harder.

Remember

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice bin and dispenser mechanism.

• Do not store anything in the ice storage bin.

IMPORTANT:

• After connecting the refrigerator to a water source or

replacing the water filter, flush the water system. Use a sturdy

container to depress and hold the water dispenser pad for

5 seconds, then release it for 5 seconds. Repeat until water

begins to flow. Once water begins to flow, continue

depressing and releasing the dispenser pad (5 seconds on,

5 seconds off) until a total of 4 gal. (15 L) has been

dispensed. This will flush air from the filter and water

dispensing system, and prepare the water filter for use.

Additional flushing may be required in some households. As

air is cleared from the system, water may spurt out of the

dispenser.

• Allow 24 hours for the refrigerator to cool down and chill

water.

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The dispensing system will not operate when the refrigerator

door is open.

Calibrate Measured Fill

Household water pressure may affect the accuracy of the

Measured Fill feature. So, for optimum performance of your water

dispenser, you must first calibrate Measured Fill.

IMPORTANT: Flush the water system before calibrating

Measured Fill.

1. Place a sturdy measuring cup (1 cup size) on the dispenser

tray centered in front of the water dispenser paddle.

NOTE: Depending on your model, a measuring cup may be

provided.

k_/ w

A. Water dispenser paddle

B. Measuring cup (1 cup)

Press and hold the OPTIONS and LOCK buttons at the same

time for 3 seconds. The words "Back" and "1 Cup" will

appear on the display screen. Also, the Calibrate Measured

Fill icon will illuminate and remain lit while the Measured Fill

feature is being calibrated.

NOTE: You may press ICE TYPE, under Back, at any time to

exit calibration mode. The Calibrate Measured Fill icon will

disappear.

Press and release the water dispenser paddle, as needed, to

dispense water to the 1 cup fill line.

NOTE: If overfilling or spilling occurs, discard the water and

press ICE TYPE to restart the calibration process.

The Water Dispenser

IMPORTANT: Dispense at least 1 qt (1 L) of water every week to

maintain a fresh supply.

To Dispense Water (Standard):

1. Press a sturdy glass against the water dispenser lever.

NOTE: While dispensing water and for 3 seconds after

dispensing has stopped, the digital display will show how

much water has been dispensed.

2. Remove the glass to stop dispensing.

To Dispense Water (Measured Fill):

Measured Fill allows you to dispense a specified amount of water

with the touch of a few buttons.

NOTE: The amount of water you select will be dispensed. Be

sure that the container is empty and can hold the entire volume. If

ice is in the container, you may need to adjust your selection.

1. Press MEASURED FILL to turn the feature on. When the

feature is on, the Measured Fill screen appears on the display.

When 1 cup of water has been correctly dispensed into the

measuring cup, press the MEASURED FILL button under the

word "Confirm" to confirm the calibration.

A. 1 cup of water

When Measured Fill calibration has been confirmed the icons

will disappear and the display will return to the home screen.

Press ICE TYPE to manually turn off the Measured Fill feature.

NOTE: The dispenser will automatically turn off Measured Fill

after 1 minute of inactivity. When Measured Fill is turned off,

any changes you have made will be lost and all defaults will

be restored.

You can dispense water by the ounce, cup, or liter. The

default unit is ounces. To switch to cups or liters, press the

LIGHT button.

Default, minimum, and maximum volumes are listed below.

Units Default Minimum Maximum

Ounces 8 1 128

Cups 1 1/4 16

Liters 0.25 0.05 4.00

3. Press the LOCK and OPTIONS buttons to adjust the volume

as desired. The LOCK button increases the volume, and the

OPTIONS button lowers the volume.

NOTE: Most coffee cups (commonly 4 to 6 oz [118 to

177 mL] per cup) are not the same size as a measuring cup

(8 oz [237 mL]). You may need to adjust the volume to avoid

unintentionally overfilling coffee cups.

4. To dispense water, press a sturdy glass against the water

dispenser lever OR place the glass below the water dispenser

and press the MEASURED FILL button.

NOTE: While dispensing water, the digital display will count

down how much water remains to be dispensed, according

to the volume you selected. The flow of water will

automatically stop once the desired volume has been

dispensed.

5. To stop dispensing before the selected volume has been

dispensed, remove the glass from the dispenser lever OR

press the MEASURED FILL button a second time.

NOTE: If you stop dispensing before the desired volume has

been dispensed, the digital display will continue to show how

much water remains to be dispensed. The display will turn off

after 1 minute of inactivity.

• To select a new volume or start dispensing the same volume

again, you must first finish dispensing the selected volume, or

turn off the Measured Fill feature (either by waiting 1 minute

so it will automatically turn off or by pressing ICE TYPE to

manually turn it off) and then turn it back on.

Rotating Faucet and Pull-out Tray (on some models)

On some models, the dispenser has a rotating water faucet and a

pull-out tray at the bottom.

A. Faucet rotated

B. Pull-out tray

The faucet rotates to the center to allow for easy dispensing

into large containers. To rotate it, push in on the right-hand

side of the faucet as shown.

Push in on the left-hand side to rotate the faucet back into

place.

NOTE: When using the dispenser with the faucet rotated, do

not use the water dispenser pad. Use only the water

dispenser button to dispense. Dispensing by pressing the

container against the water dispenser pad may result in

unintentional spilling.

The tray can be pulled out a bit in order to better support

large containers. It is designed to catch small spills and allow

for easy cleaning. There is no drain in the tray.

NOTE: The tray can be removed from the dispenser and

carried to the sink to be emptied or cleaned. Pull the tray out

until it hits the stop, then gently lift up on the back of the tray

and slide it out the rest of the way.

The Ice Dispenser

Ice is dispensed from the ice maker storage bin in the freezer

when the dispenser lever is pressed. To turn off the ice maker,

see "Ice Maker and Storage Bin."

Your ice maker can produce both crushed and cubed ice. Before

dispensing ice, select which type of ice you prefer by pressing

the ICE TYPE button.

The display screen indicates which type of ice is selected.

UL]

CRUSHED CUBED

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When you are changing from crushed to cubed, a few ounces of

crushed ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Make sure the desired type of ice is selected. To switch

between cubed and crushed, press ICE TYPE.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

NOTE: Ice may continue to be dispensed for several seconds

after you remove the glass from the lever. The dispenser may

continue to make noise for a few seconds after dispensing.

The Dispenser Light

When you use the dispenser, the light will automatically turn on.

If you want the light to be on continuously, you may choose either

On or Pads. The display screen indicates which mode is

selected.

• Press LIGHT to toggle through the following choices in a

continuous loop.

Off: (default) The dispenser light is off.

On: To turn on both the dispenser light and the light behind

the dispenser paddles.

Pads (dispenser paddles): To turn off the dispenser light, but

keep the light behind the dispenser paddles on.

The dispenser lights are LEDs that do not need to be replaced. If

it appears that your dispenser lights are not working, see

"Troubleshooting" for more information.

The Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the

refrigerator, to the ice maker, or to the dispenser light. It simply

deactivates the controls and dispenser levers. To turn off the ice

maker, see "Ice Maker and Storage Bin."

• Press and hold LOCK for 3 seconds to lock the dispenser.

• Press and hold LOCK a second time to unlock the dispenser.

The display screen indicates when the dispenser is locked.

& &

LOCKED UNLOCKED

The water filter is located in the upper right-hand corner of the

refrigerator compartment.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status

When a water filter has been installed in the refrigerator, the water

filter status lights help you know when to change your water filter.

• The "Order Filter" icon will illuminate when 90% of the volume

of water for which the filter is rated has passed through the

filter OR 5 months have passed since the filter was installed.

• The "Replace Filter" icon will illuminate and blink

continuously during dispensing when the rated volume of

water has passed through the filter OR 6 months have

passed since the filter was installed. A new water filter should

be installed immediately when the "Replace Filter" light is

illuminated.

• After 14 days at Replace Filter stage, the "Replace Filter" and

"water" icons will glow at all times and blink continuously

during dispensing. Also, an alert chime will sound three times

following dispensing.

The disposable water filter should be replaced at least every

6 months. If the water flow to the water dispenser or ice maker

decreases noticeably before 6 months have passed, replace the

water filter more often.

Reset Water Filter Status

After changing the water filter, reset the status light. Press the

OPTIONS button to enter Options mode, then press LOCK to

initiate the reset, then press MEASURED FILL to confirm that you

want to reset the status light. When the system is reset, the

"ORDER" and "REPLACE" icons will disappear from the display

screen.

Replacing the Water Filter

To purchase a replacement water filter, model number

UKF8001AXX-750 or UKF8001AXX-200, contact your dealer or

call 1-800-253-1301 in the U.S.A. or 1-800-807-6777 in Canada.

IMPORTANT: Air trapped in the water system may cause water

and filter to eject. Always dispense water for at least 2 minutes

before removing the filter or blue bypass cap.

1. To access the filter, press upward on the ribbed section of the

water filter cover.

2. Turn filter counterclockwise to remove.

3. Remove sealing label from replacement filter and insert the

filter end into the filter head.

4. Turn the filter clockwise until it stops. Snap the filter cover

closed.

5. Flush the water system. See "Water and Ice Dispenser."

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. If this option is chosen,

replace the filter with the blue bypass cap.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid odor

buildup. Wipe up spills immediately.

IMPORTANT:

• Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, nail polish remover, bleaches or

cleansers containing petroleum products. Do not use paper

towels, scouring pads, or other harsh cleaning tools that may

scratch or damage the materials.

Clean the Interior

1. Unplug refrigerator or disconnect power.

2. Using a clean sponge or soft cloth and a mild detergent in

warm water, hand wash, rinse, and dry removable parts and

interior surfaces thoroughly.

3. Plug in refrigerator or reconnect power.

Clean the Touch Screen Display on the Dispenser Panel

1. Make sure the refrigerator is unplugged or the power is

disconnected before wiping the screen, to avoid

unintentionally changing the settings.

2. Mix a solution of mild detergent in warm water. Dampen a

soft, lint-free cloth with the solution and gently wipe the

screen.

NOTE: Do not spray or wipe liquids directly onto the screen,

or over-saturate the cloth.

3. Plug in refrigerator or reconnect power.

Clean the Exterior Surfaces

Unplug refrigerator or disconnect power.

Using a clean sponge or soft cloth and a mild detergent in

warm water, wash, rinse and thoroughly dry stainless steel

and painted metal exteriors.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner and Polish, Part Number 4396920. To order the

cleaner, call 1-800-422-1230 U.S.A. or 1-800-807-6777

Canada.

IMPORTANT: This cleaner isfor stainless steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to come

into contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth.

Plug in refrigerator or reconnect power.

Clean the Condenser

There is no need for routine condenser cleaning in normal home

operating environments. If the environment is particularly greasy

or dusty, or there is significant pet traffic in the home, the

condenser should be cleaned every 2 to 3 months to ensure

maximum efficiency.

To clean the condenser:

1. Unplug refrigerator or disconnect power.

2. Remove the base grille.

3. Use a vacuum cleaner with asoft brush to clean the grille, the

open areas behind the grille and the front surface area of the

condenser.

4. Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size, shape,

and wattage (no greater than 40 watts).

• The dispenser lights are LEDs that cannot be changed.

• On some models, the interior lights are LEDs that cannot be

changed.

• Some models may have LEDs in one compartment and an

appliance bulb in another compartment.

To Replace an Appliance Bulb:

1. Unplug refrigerator or disconnect power.

2. Remove the light shield(s), if necessary.

• Squeeze both sides of the light shield while pulling

downward to remove.

3. Replace burned-out bulb(s) with appliance light bulb(s) no

greater than 40 watts.

4. Replace the light shield(s) by inserting the tabs on the shield

into the liner holes and snap into place.

NOTE: To avoid damaging the light shield, do not force the

shield beyond the locking point.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to foUow these instructions can result in death,

fire, or electrical shock.

Power cord unplugged?Plug intoa grounded 3 prong

outlet.

Is outlet working? Plug in a lamp to see if the outlet is

working.

Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Control(s)."

New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

• Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during

defrost cycle

• Popping - contraction/expansion of inside walls, especially

during initial cool-down

• Water running - may be heard when ice melts during the

defrost cycle and water runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back into the

correct position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below

are listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker

• Pulsating - fans/compressor adjusting to optimize

performance

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Control(s)."

Temperature is too cold in refrigerator

• Refrigerator air vent blocked? If the air vent located in the

top, left, rear corner of the refrigerator compartment is

blocked by items placed directly in front of it, the refrigerator

will get too cold. Move items away from the air vent.

• Ice storage bin in correct position? See "Ice Maker and Ice

Storage Bin."

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting warmer. Check temperature in

24 hours. See "Using the Control(s)."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to

enter refrigerator. Minimize door openings and keep doors

fully closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

Ice maker turned on? Make sure ice maker is on. See "Ice

Maker and Ice Storage Bin."

New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

Refrigerator door closed completely? Close the door

firmly. If it does not close completely, see "The doors will not

close completely."

Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice volume improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice quality improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

Odor transfer from food? Use airtight, moisture proof

packaging to store food.

Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

Water filter installed on the refrigerator? Gray or dark

discoloration in ice indicates that the water filtration system

needs additional flushing. Flush the water system before

using a new water filter. Replace water filter when indicated.

See "Water Filtration System."

The water and ice dispenser will not operate properly

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? Straighten the water source

line.

• New installation? Flush and fill the water system. See "Water

and Ice Dispensers."

• Is the water pressure at least 35 psi (241 kPa)? The water

pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements."

• Water filter installed on the refrigerator? Remove filter and

operate dispenser. If water flow increases, the filter may be

clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Water dispenser measured fill feature is not dispensing

an accurate amount of water? Calibrate the water

dispenser. See "Water and Ice Dispensers."

• Refrigerator door closed completely? Close the door

firmly. If it does not close completely, see "The doors will not

close completely."

• Recently removed the doors? Make sure the water

dispenser wire/tube assembly has been properly reconnected

at the top of the refrigerator door. See "Refrigerator Doors

and Drawer."

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

Water is leaking from the dispenser system

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

• New installation? Flush the water system. See "Water and

Ice Dispensers."

• Recently changed water filter? Flush the water system. See

"Water and Ice Dispensers."

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C).

• New installation? Allow 24 hours after installation for the

water supply to cool completely.

• Recently dispensed large amount of water? Allow

24 hours for water supply to cool completely.

• Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water

Supply Requirements."

WATER FILTER CERTIFICATIONS

State of Calilbrnia

Department of Public tteakh

WaterTreatmentDevice

CertificateNumber

03- 1583

Datelssued: September I6, 2008

Date Revised: April 22, 2009

Trademark/Model Desiunation

L KF8001AXX-750

_6 9006-750

67003523-75C

Manufacturer: Cuno [nc

Reatacement Elements

UKb80oi

Turbidity

Organic Contanlinants

Atrazine

Linda_c

Benzene

Carboluran

p-dmhlorobenzene

Toxaphene

Tetrachtoroethy]cne

Rated Service Capaci_: 750 gal. Rated Service Flow: 078 gpm

Conditions of Certification:

Do not use where water is microbiologically imsal_ or with water o fm,&nowrt quality, except that systems certified

lbr cyst reduction may be used on disinl_cted waters that may contain filterable cysts.

State of California

Department of Public tlealth

WaterTreatmentDevice

CertificateNumber

09- 1979

Date Issued: Ma_ 8, 2009

Date Revised: 6/22/2010

Trademark/Model Designation Reolacement Elements

UKFS001AXX-200 : UKFS001

Kenmore 46 9 ..... 46 9006

Manuthcturer:

Cysts

Turbidityl

Benzene

Carbofuraa ::

Chlorobenz_n¢

Endrin

Ethglbenzene

Lindane : .....

Rated Service Capacity': 200 gal Service Flow: 0.55 _pm

Do not use where water is mierobi01_ii¢i!ly _safe _ v_ Watt'r _ _ nR_o_n quality, except that systems

certified lbr cyst reduction may be Used On disinfected waters fl_t ma_ contain filterable cysts.

PERFORMANCE DATA SHEETS

Interior Water Filtration System

Model UKF8001AXX-750 Capacity 750 Gallons (2839 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42 for the

reduction of Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI

Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene,

Carbofuran, Toxaphene, Cysts, Turbidity, Asbestos, Tetrachloroethylene and Lindane.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 2.00 mg/L 2.0 mg/L + 10% 0.06 mg/L 0.050625 mg/L 97.00% 97.52%

Particulate Class I* 85% reduction 14,000,000 #/mL Atparticles/mLleast10,000 370,000 #/mL** 196,666 #/mL 97.40% 99.00%

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: @ pH 6.5 0.010 mg/L 0.150 mg/U 0.15 mg/L + 10% < 0.001 mg/L < 0.001 mg/L >99.30% >99.30%

Lead: @ pH 8.5 0.010 mg/L 0.150 mg/12 0.15 mg/L _+10% < 0.001 mg/L < 0.001 mg/L >99.30% >99.30%

Mercury: @ pH 6.5 0.002 mg/L 0.006 mg/L 0.006 mg/L + 10% 0.0005 mg/L 0.0003 mg/L 91.70% 95.00%

Mercury: @ pH 8.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _+10% 0.0018 mg/L 0.00073 mg/L 69.20% 88.10%

Benzene 0.005 mg/L 0.0133 mg/L 0.015 mg/L _+10% 0.0005 mg/L 0.0005 mg/L 96.10% 96.30%

p-Dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/L >99.80% >99.80%

Carbofuran 0.040 mg/L 0.0753 mg/L 0.08 mg/L _+10% 0.027 mg/L 0.008 mg/L 64.60% 73.45%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 _+10% < 0.001 mg/L < 0.001 mg/L >93.3% >93.3%

Atrazine 0.003 mg/L 0.0102 mg/L 0.009 mg/L _+10% 0.0027 mg/L 0.00105 mg/L 76.30% 89.40%

Asbestos >99% 126.5 MF/L 107to 108fibers/l_ tt < 0.17 MF/L < 0.17 MF/L >99.99% >99.99%

Live Cysts _ >99.95% 122,500 #/L 50,000/L min. < 1 #/U < 1 #/U >99.99% >99.99%

Turbidity 0.5 NTU 10.5 NTU 11 _+1 NTU 0.30 NTU 0.125 NTU 97.30% 98.80%

Lindane 0.0002 mg/L 0.0019 mg/L 0.002 _+10% < 0.00016 mg/L 0.000035 mg/L 91.80% 97.90%

Tetrachloroethylene 0.005 mg/L 0.015 mg/L 0.015 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/L >96.6% >96.6%

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.78 gpm (2.9 Lpm). Pressure =

(20°0 _+3°0).

• It is essential that operational, maintenance, and filter •

replacement requirements be carried out for the product to

perform as advertised.

• The disposable water filter should be replaced at least every

6 months.

The filter monitor system measures the amount of water that

passes through the filter and alerts you to replace the filter.

When 90% of the filter's rated life is used, the yellow (Order)

light comes on. When 100% of the filter's rated life is used,

the red (Replace) light comes on, and it is recommended that

you replace the filter. For models without filter status lights,

replace the filter every 6 months. Use replacement filter

model UKF8001. 2011 suggested retail price of

$44.99 U.S.A./S49.95 Canada. Prices are subject to change

without notice.

The product is for cold water use only.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

60 psig (413.7 kPa). Temp. = 68°F _+5°F

Refer to the "Water Filtration System" section for the

Manufacturer's name and telephone number.

Refer to the "Warranty" section for the Manufacturer's limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 35 - 120 psi (241 - 827 kPa)

Water Temperature 33° - 100°F (1o_38oc)

Service Flow Rate 0.78 gpm (2.9 L/min.) @ 60 psi

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

tThese contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

ttFibers greater than 10 um in length

_Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

La page charge ...

Maytag MFX2570AEB0 User Instructions

Marque: Maytag

Modèle: MFX2570AEB0

Catégorie: Frigos

Taper: User Instructions

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MFX2570AEB0

Maytag MFX2570AEB0 User Instructions

Maytag MFX2570AEB0 User Instructions

dans d''autres langues

Documents connexes

Autres documents