Kobalt 2600503 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
Français p. 22
80 V SNOW THROWER
ITEM #0727352
MODEL #2600503
Serial Number
Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-456-8934, 9 a.m. - 8 p.m., EST, Monday - Thursday,
9 a.m. - 5 p.m., EST, Friday - Saturday.
AB17560
ATTACH YOUR RECEIPT HERE
1
2
TABLE OF CONTENTS
PRODUCT SPECIFICATIONS
Product Specications............................................................................................................2
Package Contents................................................................................................................3
Hardware Contents...............................................................................................................4
Symbols................................................................................................................................ 5
Safety Information .............................................................................................................7
Preparation ........................................................................................................................... 8
Assembly Instructions ........................................................................................................ 9
Operating Instructions ....................................................................................................... 12
Care and Maintenance........................................................................................................ 15
Troubleshooting........................................................................................................................ 19
Warranty ................................................................................................................................ 20
Replacement Parts List...................................................................................................... 21
SPECIFICATIONS
Type Cordless, battery-operated
Motor 80 V brushless motor
No-load speed 1,900 RPM
Working width 20 in.
Cleaning depth 10 in.
Impeller size 16 in.
Wheels 7 in.
Discharge distance 20 ft.
Weight (without battery) 34.6 lbs.
3
PART DESCRIPTION QUANTITY
A Upper chute control rod 1
B Lower chute control rod 1
C Middle handle 1
D Upper handle 1
E Chute deector 1
F Battery 1
G Charger 1
H Lower handle 1
I Discharge chute 1
J Handle of the chute
control rod
1
PACKAGE CONTENTS
A
B
C
D
E
F
G
PART DESCRIPTION QUANTITY
K Battery compartment
cover
1
L Battery release button 1
M Safety switch button 1
N Bail lever 1
O LED lights 1
P Trigger 1
Q Left side cover 1
R Drive Belt 1
S Small pulley 1
T Large pulley 1
H
I
J
K
L
M
N
O
P
S
R
T
Q
4
HARDWARE CONTENTS (not shown actual size)
AA
Cam locks
Qty. 2
BB
Bolts
Qty. 2
CC
DD
Handle knobs
Qty. 4
Hitch pin
Qty. 1
5
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their mean-
ing. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOLS NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
Wh Watt Hour Energy Storage Capacity
Ah Amp Hour Current Capacity
Direct Current Type or a characteristic of current
RPM Rotating Speed Revolutions per minute
/min Per Minute Revolutions, strokes, surface speed, orbits
,
etc., per minute
Wet Conditions Alert Do not expose to rain or use in damp locations.
Read The Operator’s
Manual
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye and Hearing
Protection
Wear eye and hearing protection when operating this
equipment.
Safety Alert Precautions that involve your safety.
Hand and Feet Keep hands and feet away.
Safe Distance Keep bystanders a safe distance from the machine.
Stop the Machine
Stop the motor and remove the battery before leaving the
machine.
Moving Parts
Stay away from moving parts. Keep all guards and
shields in place.
Thrown objects
Thrown objects can ricochet and result in personal injury or
property damage.
Hand and feet Keep hands and feet away from rotating impeller.
Hand Keep hands away from the discharge area.
6
The following signal words and meanings are intended to explain the levels of risk associated
with this product.
WARNING
To avoid serious personal injury, do not attempt to use this product until you have read this Owner's
Manual thoroughly and understand it completely. If you do not understand the warnings and
instructions in this Owner's Manual, do not use this product.
Call 1-866-456-8934 for assistance.
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before operating a power tool, always wear safety goggles,
safety glasses with side shields, or a full face shield when needed. We recommend a Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always
use eye protection that is marked to comply with ANSI Z87.1.
SYMBOL SIGNAL MEANING
DANGER
Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury.
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may
result in property damage.
SYMBOLS
7
WARNING
SAFETY INFORMATION
Read and understand all instructions before using this product. Failure to follow all instructions listed
below may result in electric shock, re, and/or serious personal injury.
The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
Walk. Do not run.
Verify that the power tool is not in contact with anything before turning it on.
Stay away from impeller openings at all times. Keep face, hands, and feet away from concealed,
moving, or rotating parts.
Be attentive when using the power tool. Stay alert for holes in the terrain and other hidden hazards
or trafc.
Move up and down slopes when clearing snow. Do not go across a slope. Use caution when
changing direction. Do not use this power tool to clear snow from steep slopes.
Do not operate the power tool if the guards, plates, and other safety protective devices are not in
place.
Do not operate the power tool near glass enclosures, automobiles, trucks, window wells, drop-offs,
etc., without properly adjusting the angle of the snow discharge. Keep children and pets away from
the work area.
Do not operate the power tool at high speeds on slippery surfaces. Look behind when backing up
and exercise caution.
Wear safety glasses or goggles that meet ANSI Z87.1 standards.
Use the power tool in daylight or in good articial light.
To avoid accidental start-ups, remain in the starting position when turning the power tool on. The
operator and the power tool must be in a stable position during start-up. See the section titled
Starting/Stopping Instructions.
Use this power tool only for the purposes it was designed.
Hold the power tool with both hands while it is in use. Keep a rm grip on the handles.
If the impeller does not rotate freely due to ice, thaw the power tool thoroughly before attempting to
use it.
Keep the impeller clear of debris.
Do not attempt to clear the impeller while the motor is running.
After striking a foreign object, turn the power tool off and remove the battery pack, then inspect it for
damage. Repair any damage before restarting and using the power tool.
If the power tool starts to vibrate abnormally, stop the power tool immediately and attempt to
determine the cause. Vibration is generally an indication of danger.
Stop the motor and remove the battery pack whenever the operator is not in the operating position,
before unclogging the impeller, and before making any repairs, adjustments, or inspections.
Do not use on graveled surface unless the power tool is adjusted for such a surface in accordance
with the operator’s manual.
Keep Children Away – All visitors should be kept a safe distance from work area.
Dress Properly – Do not wear loose clothing or jewelry. They can be caught in moving parts.
Wear rubber boots when operating the power tool. Do not operate the equipment when barefoot or
wearing open sandals. Always wear substantial footwear.
Operation of the power tool in the hand-held position is unsafe, except in accordance with the
special instructions for such use provided in the operator’s manual.
8
SAFETY INFORMATION
Keep guards in place and in working order.
Don’t Force Power Tool – It will perform better and safer at the rate for which it was designed.
Don’t Overreach – Keep proper footing and balance at all times.
If the power tool strikes a foreign object, follow these steps:
i) Stop the power tool.
ii) Inspect for damage.
iii) Repair any damage before restarting and operating the power tool.
Store Idle Power Tool Indoors – When not in use, power tools should be stored indoors in a dry,
locked-up place out of reach of children.
Maintain Power Tools With Care – Follow instructions for lubricating and changing accessories.
Allow the power tool to run for a few minutes after clearing snow in order to prevent moving parts
from freezing.
Only use identical replacement parts and accessories for this power tool. The use of nonidentical
parts or accessories could lead to serious injury to the user or damage the power tool, and will void
the warranty.
Do not pick up the power tool while it is running. The power tool is designed to travel along the
ground.
Never allow children to operate a power tool. Keep the area of operation clear of all persons,
particularly small children, and pets.
Thoroughly inspect the area where the equipment is to be used and remove all stones, sticks,
wires, bones, and other foreign objects.
Stop the blade(s) when crossing gravel drives, walks, or roads.
Use only 80-volt Kobalt batteries.
Read the operating and service instruction manual carefully. Be thoroughly familiar with the controls
and the proper use of the equipment.
GENERAL SAFETY RULES
Verify that the power tool is secure while transporting.
Store the power tool in a dry area that will prevent unauthorized use or damage. Keep out of the
reach of children.
Keep handles dry, clean, and free of debris. Clean the power tool after each use. Refer to the
Maintenance Section in this manual for more information.
If the labels on the power tool become defaced or start to lift off, contact customer service
at 1-866-456-8934.
Keep these instructions in a safe place for future reference. Refer to them often and use them to
instruct other users. Anyone who uses this power tool must read these instructions carefully.
Maintain the power tool with care. Follow the instructions for lubricating and changing accessories.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assem-
ble the product.
Estimated Assembly Time: 5 minutes
9
1a. Align the holes on the middle handle (C) and
the lower handle (H). Insert the bolts (BB) and
use the handle knobs (CC) to tighten them.
WARNING
Do not allow familiarity with this product to make you careless. Remember that a careless fraction
of a second is sufcient to inict serious injury.
Do not use any attachments or accessories not recommended by the manufacturer of this product.
The use of attachments or accessories not recommended can result in serious personal injury.
1. ASSEMBLING THE HANDLES
ASSEMBLY INSTRUCTIONS
1b
1a
C
H
CC
BB
1b. Align the hole on the middle handle (C) and
the upper handle (D). Insert the cam locks
(AA) and tighten them with the handle knobs
(CC) provided. Once tightened, close the cam
locks to secure them in place.
NOTE: If the upper handle is loose or seperated
from the middle handle, tighten the cam locks and
the handle knobs by turning them clockwise. Do
not overtighten the handle knobs.
C
D
CC
AA
10
ASSEMBLY INSTRUCTIONS
3. INSTALLING THE CHUTE CONTROL ROD
3a. Align the holes on the upper chute control rod
(A) with the holes on the lower chute control
rod (B). Insert the hitch pin (DD).
NOTE: Position the discharge chute (I) so that it
faces forward.
3b. Insert the end of the chute control rod through
the keyed hole in the bracket that is attached
to the top of the middle handle (C).
Ensure that the handle (J) of the chute control
rod points upward and insert the rod into the
keyed hole in the back of the housing.
Firmly push the rod into the keyed hole in the
back of the housing until it snaps into place.
2a
E
Latching tab
Keyed holeSlot
Post
2. ASSEMBLING THE DISCHARGE CHUTE
2a. Push the chute deector (E) until the latching
tabs on both sides click into the slots and the
posts on both sides click into the keyed holes.
3a
A
B
DD
Holes
3b
I
Keyed hole
J
Keyed hole
C
11
ASSEMBLY INSTRUCTIONS
M
N
O
4a. TO INSTALL BATTERY PACK
Open the battery compartment cover (K).
Align the battery (F) with the cavity in the snow
thrower housing.
Slide the battery down to lock it into position.
The battery is fully inserted into the snow
thrower when you hear an audible “click”.
Close the battery compartment cover.
4b. TO REMOVE BATTERY PACK
Release your grip on the bail lever to stop the
snow thrower.
Press the battery release button (L) in the snow
thrower housing. This will cause the battery to
raise out of the tool slightly.
Remove battery pack from the snow thrower.
3c
3c. Rotate the handle (J) on the chute control rod
to ensure that it moves in the same direction
as the chute.
J
WARNING
Always remove battery from your tool when you are assembling parts, making adjustments, cleaning,
or when not in use. Removing battery will prevent accidental starting that could cause serious person-
al injury.
4
K
F
L
12
OPERATING INSTRUCTIONS
1. POWERING ON AND OFF
To power on, rst press the safety switch button (M).
While pressing the safety switch button with one hand, use your other hand to simultaneously pull
the bail lever (N) toward you. Once the machine powers on, release the safety switch button and
proceed with operation. The snow thrower can only be started by pressing the safety switch button
rst, followed by squeezing the bail lever; reverse operation will not start the machine.
To power off, release your grip on the bail lever (N).
CAUTION
Do not attempt to override the operation of the safety switch button or bar lever.
WARNING
The operation of any snow thrower can result in foreign objects being thrown into the eyes, which
can cause severe eye damage. Always wear safety glasses while operating the snow thrower and
while performing any adjustments or repairs.
Keep bystanders a safe distance from the machine.
INSPECT THE CLEARING AREA. Remove all stones, sticks, wire, bones, and other debris that
might be thrown by the rotating impeller.
1
M
N
N
13
OPERATING INSTRUCTIONS
2. UTILIZING THE LED LIGHTS
To utilize the LED lights (O) for night time snow
removal, press the safety switch button (M) and
then pull the bail lever (N) toward you.
To turn off the LED lights, release the bail lever.
2
O
N
M
3. ADJUSTING THE DISCHARGE CHUTE AND
CHUTE DEFLECTOR
To adjust the discharge chute (I), rotate the
handle (J) on the chute control rod in the
direction that you wish to direct the snow
stream.
To adjust the chute deector (E) and control the
height of the snow stream, squeeze the trigger
(P) to raise or lower the chute deector.
3
J
P
E
I
14
OPERATING INSTRUCTIONS
OPERATING TIPS
WARNING
If the snow thrower hits a foreign object while it is in use, the object could be thrown in the direction of
the operator or a bystander. Thrown objects could cause serious personal injury. Keep the area to be
cleared free of all foreign objects that may be picked up and thrown by the impeller.
Keep the area of operation free of foreign objects that can become thrown by the impeller. Per-
form a thorough inspection of the area since some objects may be hidden from view by surround-
ing snow. lf the snow thrower hits an obstruction or picks up a foreign object during use, stop the
snow thrower, remove the battery, remove the obstruction, and inspect the unit for damage. Repair
or replace any damaged part before restarting and operating the unit.
Keep children, pets, and bystanders away from the area of operation. Be aware that the normal
noise of the machine when turned on may make it difcult for you to hear approaching people.
When moving the snow thrower, use the wheels on one side as the pivot point. Slightly tilt the
snow thrower on this pivot point to move it forward or backward.
Start your clearing path outward, throwing snow in a back and forth motion. To clear in the oppo-
site direction, pivot the snow thrower on its wheels. Make sure to overlap clearing paths.
Note the wind direction. If possible, move in the same direction as the wind so that the snow is not
thrown against the wind (and thus back onto you and on the just cleared path).
Do not push the snow thrower with excessive force. You should push the machine gently and at a
consistent speed in accordance with the unit's throw rate.
Some parts of the snow thrower may freeze under extreme temperature conditions. Do not at-
tempt to operate the snow thrower with frozen parts. If the parts freeze while the snow thrower
is in use, stop the snow thrower, remove the battery, and inspect for frozen parts. Free all parts
before restarting or operating the snow thrower. Never force controls that are frozen.
When working on pebbles, gravel, or unpaved surfaces, avoid throwing loose surface material
along with the snow by pushing down on the handle to raise the scraper at the base of the unit
above the pebbles or gravel.
Cold Weather Operation: Lithium Ion batteries can be safely used from temperatures ranging from
1°F (-17°C) to 113°F (45°C).
NOTE: Do not store or charge battery outside. Battery must be charged and stored indoors prior
to use of the snow thrower.
If the snow thrower does not start, initially remove battery from snow thrower. Place battery on
charger and allow to charge for 10 minutes. Remove from charger and install in snow thrower for
use. The start-up issue may be caused from the battery being too cold. To avoid this issue, ensure
battery is stored in a dry cool place for storage and charging and leave indoors until ready for use.
15
CARE AND MAINTENANCE
Screw
Screw
Remove the 3 screws from under the machine
that secure the scraper to the machine.
Remove and discard the old scraper. Install
the new scraper and fasten it securely with 5
screws previously removed.
3 Screws
1
IMPORTANT: Always remove the
battery from the tool before performing any
maintenance on it.
1. REPLACING THE SCRAPER
NOTE: The scraper is located at the bottom of the
impeller housing. Ensure that the battery is not
installed in the tool.
Remove the screw from each side plate that
holds the scraper.
16
CARE AND MAINTENANCE
2. REPLACING THE DRIVE BELTS
Remove the 5 screws that secure the left side
cover (Q) to the frame of the snow thrower.
Remove the side cover.
2
5 Screws
Q
S
R
T
Remove the old belt (R) from the small pulley
(S) and large pulley (T).
Loop one end of the new belt over the small
pulley.
Rotate the impeller with the left hand while
positioning the belt on the large pulley with the
right hand.
Install the left side cover and secure it using
the 5 screws.
17
CARE AND MAINTENANCE
3. REPLACING THE IMPELLER
3a
3d
3g
3b
Remove the 5 screws
that secure the right
side cover.
3c
3e
3f
Remove the nut from
the right of the axle.
Remove the 5 screws
that secure the left
side cover.
Remove the belt. Using a socket (not included),
remove the the large pulley
inside the left side cover.
Remove the 6 screws
that secure the left side
plate.
3h
3i
Pull the axle and remove the
old impeller. Install the new
impeller and insert the axle.
Reinstall the nut and right side cover.
Reinstall the left side plate, large pulley, belt and left side cover.
18
CARE AND MAINTENANCE
SERVICE
Servicing requires extreme care and knowledge and should be performed only by a qualied service
technician. For service, it is suggested you return the product to your nearest AUTHORIZED SER-
VICE CENTER for repair. When servicing, use only identical replacement parts.
WARNING
If the battery pack is installed into the snow thrower, the snow thrower could start accidentally while
the operator is performing maintenance on it, which could cause serious personal injury. Remove the
battery pack before performing any maintenance.
STORAGE
Run the snow thrower for a few minutes in order to melt any snow that may be left on the snow
thrower.
Wipe the snow thrower off with a dry cloth before storage. This will help prevent ice building up on
the unit and parts freezing.
Remove the battery and store it in a cool dry location, if possible. Charge the battery every six-
months when not in use in order to increase its life.
Inspect the snow thrower thoroughly for worn, loose, or damaged parts. If any parts must be re-
paired or replaced, contact 1-866-456-8934.
Store the snow thrower in a clean, dry place. Cover it in order to provide added protection.
Always store battery and charger indoors.
19
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The handle is not
in position.
1. The bolts are not properly
seated.
1. Make sure the bolts are correctly installed
through the handle bars. Check to see if the
hand knobs are tight. Refer to Assembling
the Handles section in this manual.
The snow thrower
doesn't start.
1. The battery is not charged.
2. The switch is defective.
3. Battery is too cold.
4. The battery is not attached to
the motor.
5. Battery may require service
or replacement.
1. Charge the battery by following the
procedures in the battery and charger
manual.
2. Have the switch replaced by an authorized
service center.
3. Remove battery from snow thrower. Bring
battery and charger into warm area for 15
minutes on charge. After 15 mins, remove
from charger and install in snow thrower for
use.
4. Check the connection between the motor
connector and the battery.
5. Call customer service at 1-866-456-8934 or
replace battery.
The motor is on, but
the impeller does
not turn.
1. The belt is damaged. 1. Replace the belt (see the section entitled
Replacing the Drive Belt).
The snow thrower
leaves a thin layer
of snow behind.
1. The scraper is worn. 1. Inspect the scraper for wear or damage. Re-
place the scraper (see the section entitled
Replacing the Scraper).
If you still have questions or an unresolved issue after going through this troubleshooting guide, or
just want to speak to a Kobalt product expert, please call our customer service department at
1-866-456-8934, 9 a.m. - 8 p.m., EST, Monday - Thursday, 9 a.m. - 5 p.m., EST, Friday - Saturday.
20
WARRANTY
5-YEAR REPAIR WARRANTY
This 80 V Lithiuim-Ion snow thrower is warranted to the original purchaser from the original purchase
date for ve (5) years subject to the warranty coverage described herein.
This 80 V Lithiuim-Ion snow thrower is warranted for the original user to be free from defects in material
and workmanship.
If you believe that the 80 V Lithiuim-Ion snow thrower is defective at any time during the specied war-
ranty period, simply return the 80 V Lithiuim-Ion snow thrower along with proof of purchase to the place
of purchase for a free replacement or refund, or call 1-866-456-8934 for warranty service.
This warranty is void if: defects in materials or workmanship or damages result from repairs or alter-
ations which have been made or attempted by others or the unauthorized use of nonconforming parts;
the damage is due to normal wear, damage is due to abuse (including overloading of the tool beyond
capacity), improper maintenance, neglect or accident; or the damage is due to the use of the tool after
partial failure or use with improper accessories or unauthorized repair or alteration.
This warranty gives you specic legal rights, and you may also have other rights that vary from province
to province.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Kobalt 2600503 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur

dans d''autres langues