Philips CED228/98 Guide de démarrage rapide

Philips
Marque
Philips
Modèle
CED228/98
Taper
Guide de démarrage rapide
Register your product and get support at
CED228
ENG Quick Start Guide
English
Overview of parts
These are the supplierd parts needed to connect and install this unit.
a
c
f
d
e
b
a Carry case with front panel stored inside
b Trim plate
c Standard connector
d Rubber cushion
e Removal keys x 2 pcs
f Screw x 5 pcs
Connect wires: ISO connectors
1
Pull out the ISO connectors from the
car dashboard and connect them to
the bigger end of the supplied standard
connector.
2
Connect the other end of supplied
standard connector to the unit.
3
Do the other connections, if applicable.
Connect wires: without ISO connectors
1
2
3
4
5
6
7
8
1
Cut off the bigger end of the supplied standard connector.
2
Check the car’s wiring carefully, then connect them to the standard connector.
Connector Connect to
1
Black wire A metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
2
Yellow wire The +12V car battery which is live at all times.
3
Orange/white wire Illumination switch
4
Red wire The +12V power terminal which is live in the accessory
(ACC) position of the ignition switch
If there is no accessory position, connect to the +12V car bat-
tery terminal that is always live. Be sure to connect the black
JURXQGHDUWKOHDGWRDPHWDOVXUIDFHRIWKHFDUÀUVW
5
Green and green/black wires Left speaker (Rear)
6
White and white/black wires Left speaker (Front)
7
Gray and gray/black wires Right speaker (Front)
8
Purple and purple/black wires Right speaker (Rear)
3
Connect the supplied standard connector to the unit.
4
Do the other connections, if applicable.
Connect parking brake cable
Connect reverse driving cable
Attach the front panel Mount in the dashboard
Note
For proper operation of the DVD player, the chassis must be mounted within 20 degree horizontal.
Ensure that the unit is mounted within this limitation.
Check wire connection before you mount the unit into a car.
If preset radio stations are lost when the ignition key is turned OFF and then back ON, reconnect the
red leads crosswise to the yellow ones.
1
If the car does not have an on-board drive or navigation computer, disconnect the negative terminal
of the car attery.
If you disconnect the car battery in a car that has an on-board drive or navigation computer, the 
computer may lost its memory.
If the car battery is not disconnected, to avoid short-circuit, ensure that bare wires do not touch 
each other.
2
Ensure that car dashboard opening is within
these measurements.
3
Remove the two transport screws on the top
of the unit.
4
Remove the mounting sleeve with the removal
keys.
5
Install the sleeve into the dashboard and bend
WKHWDEVRXWZDUGWRÀ[WKHVOHHYH
,IWKHXQLWLVQRWÀ[HGE\VOHHYHEXWE\WKH
supplied screws, skip this step.
1
Attach the trim plate.
2
Insert the left side of the panel
in the chassis until it is correctly
engaged.
3
Press the right side of the panel
until the mechanism locks it into
place.
4
Close the front panel.
6
Place the rubber cushion over the end of the
bolt.
7
Slide the unit into the dashboard until a click
sound is heard.
Turn on
1
Press the knob to turn on the unit.
The unit plays the last listened program: DVD, Tuner, USB or SD/MMC Card (if there is USB
»
device or SD/MMC card connected).
To turn off the unit, press the 
knob for more than 2 seconds.
When the unit is idle for over 3 minutes, it goes to standby mode and displays screen saver.
Set clock
1
Press MENU.
2 Press the navigation buttons to select [SETTINGS], then press SEL on the remote control.
3 Select [SYSTEM], then press .
4 Select [TIME MODE], then press .
The time mode options are displayed:
»
[12 hour mode]
[24 hour mode]
5 Select a mode, then press SEL.
6 Press to return to previous menu and select [TIME ADJUST], then press .
7 Press or to enter clock, then press SEL.
Tune to a radio station
1
Press SOURCE to select Tuner.
2 Press and hold or to select band.
»
[FM] or [AM] is displayed.
3 Press or to tune to a radio station manually.
To search for radio station automatically, press 
or for 3 seconds.
Play discs
1
Press to open the front panel.
2 Insert the disc into the disc slot with label side facing up.
Play resumes from the point where it was last stopped.
»
3 To remove the disc, press the button.
When the disc is ejected, the unit switches to TUNER mode automatically.
»
4 Close the front panel.
After a few seconds, the screen turns on.
»
For video discs, if a menu appears: press 
or to select an item, then press to start play.
For discs that contain MP3s, WMAs, or JPEGs: press 
or to select a folder/track/picture, then
press
to start play.
Insert USB device
Insert SD/MMC card
1
Slide down the USB socket cover.
2 Insert the USB device into the USB socket.
The unit starts playing from the USB
»
device automatically.
1 Press to open the front panel.
2 Insert the SD or MMC card into the card
slot.
The unit starts playing from the SD/
»
MMC card automatically.
183 mm
52m
m
4.75-5.56 mm
183 m
m
4.75-5.56 mm
8
Reconnect the negative terminal of the car battery.
Detach the front panel
The front panel can be detached and taken with you to deter theft.
Note
Before installing the unit, detach the front panel.
1
Press
to release the panel.
2
Open the panel, then push the right side panel toward the left side to disengage it from the chassis.
3
Take off the panel and store it in the supplied carry case to protect it from dirt or damage.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CED228_98_QSG_V3.0
  • Page 1 1
  • Page 2 2

Philips CED228/98 Guide de démarrage rapide

Philips
Marque
Philips
Modèle
CED228/98
Taper
Guide de démarrage rapide
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes