Kenmore Elite 59672282201 Le manuel du propriétaire

Marque: Kenmore Elite

Modèle: 59672282201

Taper: Le manuel du propriétaire

Ce manuel convient également à

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8

ENGLISH FRANÇAIS ESPAÑOL

Part No. 12642729

Form A/04/03

www.sears.com

Au Canada, www.sears.ca

Bottom Freezer Refrigerator

Use & Care Guide

Refrigerador con montaje inferior

Manual de uso y cuidado

Réfrigérateur à compartiment inférieur

Guide d’utilisation et d’entretien

Models:

596.72282200, 596.72283200, 596.72284200, 596.72289200,

596.72282201, 596.72283201, 596.72284201, 596.72289201,

596.72282202, 596.72283202, 596.72284202, 596.72289202

Important safety information

What you need to know

about safety

instructions

Warning and Important Safety

Instructions appearing in this manual are

not meant to cover all possible

conditions and situations that may occur.

Common sense, caution, and care must

be exercised when installing,

maintaining, or operating refrigerator.

Always contact your dealer, distributor,

service agent, or manufacturer about

problems or conditions you do not

understand.

Save these instructions

DANGER – Immediate hazards

which WILL result in severe personal

injury or death.

DANGER

WARNING – Hazards or unsafe

practices which COULD result in

severe personal injury or death.

WARNING

CAUTION – Hazards or unsafe

practices which COULD result in

minor personal injury.

CAUTION

To reduce risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic

precautions, including the following:

WARNING

To reduce risk of injury or death,

follow basic precautions, including

the following:

IMPORTANT: Child entrapment and

suffocation are not problems of the

past. Junked or abandoned

refrigerators are still dangerous –

even if they sit out for “just a few

days.” If you are getting rid of your

old refrigerator, please follow the

instructions below to help prevent

accidents.

Before you throw away your old

refrigerator or freezer:

➢ Take off the doors.

➢ Leave the shelves in

place so children

may not easily climb

inside.

DANGER

RECOGNIZE SAFETY

SYMBOLS, WORDS,

LABELS

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not sure this

appliance is properly grounded.

5. DO NOT ground to a gas line.

6. DO NOT ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate 103 to

126 volt, 15 amp., 60 cycle line. DO NOT modify plug on

power cord. If plug does not fit electrical outlet, have

proper outlet installed by a qualified electrician.

8. DO NOT use a two-prong adapter, extension cord or

power strip.

9. DO NOT remove warning tag from power cord.

10. DO NOT tamper with refrigerator controls.

11. DO NOT service or replace any part of refrigerator unless

specifically recommended in Use & Care or published

user-repair instructions. DO NOT attempt service if

instructions are not understood or if they are beyond

personal skill level.

12. Always disconnect refrigerator from electrical supply

before attempting any service. Disconnect power cord by

grasping the plug, not the cord.

13. Install refrigerator according to Installation Instructions. All

connections for water, electrical power and grounding

must comply with local codes and be made by licensed

personnel when required.

14. Keep your refrigerator in good condition. Bumping or

dropping refrigerator can damage unit or cause unit to

malfunction or leak. If damage occurs, have refrigerator

checked by qualified service technician.

15. Replace worn power cords and/or loose plugs.

16. Always read and follow manufacturer’s storage and ideal

environment instructions for items being stored in

refrigerator.

ENGLISH FRANÇAIS ESPAÑOL

Protection agreements

Master protection

agreements

IN THE U.S.A.

Congratulations on making a smart

purchase. Your new Kenmore

appliance is designed and manufactured

for years of dependable operation. But

like all products, it may require

preventive maintenance or repair from

time to time. That is when having a

Master Protection Agreement can save

you money and aggravation.

Purchase a Master Protection

Agreement now and protect yourself

from unexpected hassle and expense.

The Master Protection Agreement also

helps extend the life of your new

appliance. Here is what is included in

the agreement:

➢ Expert service by our 12,000

professional repair specialists.

➢ Unlimited service and no charge for

parts and labor on all covered

repairs.

➢ “No-lemon” guarantee – replacement

of your covered product if more than

three product failures occur within

twelve months.

➢ Product replacement if your covered

product cannot be fixed.

➢ Annual Preventive Maintenance

Check at your request – no extra

charge.

➢ Fast help by phone – non-technical

and instructional assistance on

products repaired in your home, plus

convenient repair scheduling.

➢ Power surge protection against

electrical damage due to power

fluctuations.

➢ Rental reimbursement if repair of

your covered product takes longer

than promised.

Once you purchase the Agreement, a

simple phone call is all that it takes for

you to schedule service. You can call

anytime day or night, or schedule a

service appointment online.

Sears has over 12,000 professional

repair specialists, who have access to

over 4.5 million quality parts and

accessories. That is the kind of

professionalism you can count on to

help prolong the life of your new

purchase for years to come. Purchase

your Master Protection Agreement

today!

Some limitations and exclusions apply.

For prices and additional information,

call 1-800-827-6655.

Sears Installation Service

For Sears guaranteed professional

installation of home appliances and

items like garage door openers and

water heaters, in the U.S.A. call

1-800-MY-HOME

Maintenance agreements

IN CANADA

Your purchase has added value because

you can depend on Sears HomeCentral

for service. With over 2,400 service

technicians and access to over 900,000

parts and accessories, we have the

tools, parts, knowledge and skills to

ensure our pledge: We Service What

We Sell.

Your Kenmore

appliance is designed,

manufactured and tested to provide

years of dependable operation. Yet any

major appliance may require service

from time to time. The Sears

Maintenance Agreement offers you an

outstanding service program, affordably

priced.

Sears Maintenance Agreement

➢ Is your way to buy tomorrow’s service

at today’s price.

➢ Eliminates repair bills resulting from

normal wear and tear.

➢ Provides for non-technical and

instructional assistance.

➢ Even if you don’t need repairs,

provides an annual Preventive

Maintenance Check, at your request,

to ensure that your appliance is in

proper running condition.

Some limitations apply. For information

concerning Sears Canada Maintenance

Agreements, call 1-800-361-6665.

Warranty

Full One Year Warranty on

Refrigerator

For one year from the date of purchase,

when this refrigerator is operated and

maintained according to instructions

attached to or furnished with it, Sears

will repair it, free of charge, if defective

in material or workmanship.

Full Five Year Warranty on Sealed

Refrigeration System

For five years from the date of purchase,

when this refrigerator is operated and

maintained according to instructions

attached to or furnished with it, Sears

will repair the sealed system (consisting

of refrigerant, connecting tubing and

compressor motor) free of charge, if

defective in material or workmanship.

The above warranty coverage applies

only to refrigerators which are used for

storage of food for private household

purposes. It excludes original and

replacement Kenmore ice & water filter

cartridges. Original and replacement

cartridges are warranted for 30 days,

parts only, against defects in material or

workmanship.

Warranty service is available by

contacting 1-800-4-MY-HOME

(1-800-469-4663).

This warranty applies only while this

product is in use in the United States

and Canada.

This warranty gives you specific legal

rights, and you may also have other

rights, which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA,

Hoffman Estates, IL 60179

NOTE: Some Reverse Osmosis home

water systems cause low water

pressure. Low water pressure can affect

the water and ice dispensing system by

causing small or hollow ice cubes and

slow water flow from the dispenser.

Service problems related to the home’s

Reverse Osmosis water system are not

covered by the warranty.

Product record

In the space below record the model

and serial numbers and purchase date

of your refrigerator. You will find the

model and serial number sticker inside

the refrigerator section on the left wall.

Model Number: 596. _______________

Serial Number: ____________________

Purchase Date: ____________________

Keep this booklet and your Sears

sales receipt in a safe place for future

reference.

ENGLISH FRANÇAIS ESPAÑOL

Contents

Important Safety Information ......................................................................................2

What You Need to Know About Safety Instructions...................................................2

Protection Agreements ................................................................................................3

Master Protection Agreements – U.S.A.....................................................................3

Maintenance Agreements – Canada .........................................................................3

Warranty ........................................................................................................................4

Product Record.............................................................................................................4

Installing Your Refrigerator ....................................................................................6-11

Measuring the Opening .............................................................................................6

Transporting Your Refrigerator...................................................................................6

Selecting the Best Location .......................................................................................6

Removing and Replacing Handles ............................................................................6

How to Remove the Hinges, Door and Drawer .........................................................7

How to Reverse the Door ..........................................................................................8

How to Replace the Hinges, Door and Drawer .........................................................8

How to Connect the Water Supply.............................................................................9

How to Level Your Refrigerator................................................................................10

Setting and Maintaining Proper Temperatures........................................................11

Initial Control Settings ..............................................................................................11

Adjusting the Controls ..............................................................................................11

Fresh Food Storage .................................................................................................11

Frozen Food Storage ...............................................................................................11

About Your Water Filter ........................................................................................12-13

Water Filter Installation and Removal......................................................................12

Water Filter Data......................................................................................................13

Fresh Food Features.............................................................................................14-15

Water Dispenser ......................................................................................................14

Interior Shelves ........................................................................................................14

Door Storage............................................................................................................14

Climate-Controlled Drawers.....................................................................................15

Freezer Features.........................................................................................................16

Automatic Ice Maker ................................................................................................16

Drawers....................................................................................................................16

Hints and Care.......................................................................................................17-18

How to Clean Your Refrigerator...............................................................................17

How to Remove Odors from Refrigerator ................................................................18

Energy Saving Ideas................................................................................................18

How to Remove and Replace Light Bulbs...............................................................18

Normal Operating Sounds.........................................................................................19

Troubleshooting ....................................................................................................20-21

Operation ............................................................................................................20-21

Ice and Water...........................................................................................................21

Français.......................................................................................................................23

Español........................................................................................................................44

Service ..........................................................................................................Back Cover

Installing your refrigerator

These instructions were provided to aid

you in the installation of your

refrigerator.

Measuring the opening

A one-half inch (

⁄2") of air space must be

provided for the top and the back of the

refrigerator. When installing your

refrigerator, measure carefully.

Subflooring or floor coverings (i.e.

carpet, tile, wood floors, rugs) may make

your opening smaller than anticipated.

Some clearance may be gained by

using the leveling procedure under

How to Level Your Refrigerator

(page 10).

IMPORTANT: If refrigerator is to be

installed into a recess where top of

refrigerator is completely covered, use

dimensions from floor to top of hinge

cap to verify proper clearance.

Transporting your

refrigerator

Follow these tips when moving the

refrigerator to final location:

➢ NEVER transport refrigerator on its

side. If an upright position is not

possible, lay refrigerator on its back.

Allow refrigerator to sit upright for

approximately 30 minutes prior to

plugging refrigerator in to assure oil

returns to the compressor. Plugging

refrigerator in immediately may cause

damage to internal parts.

➢ Use an appliance dolly when moving

refrigerator. ALWAYS truck

refrigerator from its side or

back–NEVER from its front.

➢ Protect outside finish of refrigerator

during transport by wrapping cabinet

in blankets or inserting padding

between the refrigerator and dolly.

➢ Secure refrigerator to dolly firmly with

straps or bungee cords. Thread

straps through handles when

possible. DO NOT overtighten. Over-

tightening restraints may dent or

damage outside finish.

Selecting the best

location

Observe these points when choosing the

final location for your refrigerator:

➢ DO NOT install refrigerator near

oven, radiator or other heat source. If

not possible, shield refrigerator with

cabinet material.

➢ DO NOT install where temperature

falls below 55° F (13° C). Malfunction

may occur at this temperature.

➢ To assure proper door closure, follow

the leveling instructions in the

section, How to Level Your

Refrigerator (page 10).

Removing and replacing

handles

1. Remove top and bottom door trim by

removing 4 screws*. Lift handle

corner of trim and slide toward hinge

edge of door.

➢ Retain all screws for later use.

2. Remove handle by removing 2

screws* from top and bottom edge of

handle.

➢ Retain all screws for later use.

Removing Freezer Handle

1. Remove handle by removing 3

screws* from handle.

➢ Retain all screws for later use.

Replacing Fresh Food Handle

1. Install handle by fastening with

screws* from previous removal.

2. Install top and bottom door trim.

➢ Locate hinge hole corner of trim.

Install hinge hole corner of trim,

then install handle edge of trim.

Replacing Freezer Handle

1. Install handle by fastening with

screws* from previous removal.

* Fasteners may require either a T-15 Torx

driver or a Phillips screwdriver.

Torx

is a registered trademark of Textron Inc.

To avoid possible injury and damage

to property:

➢ DO NOT remove secondary cap

when removing door trim.

➢ Place doors on nonabrasive

surface protected by towels or

rugs while working directly on

door.

CAUTION

Removing Fresh Food Handle

NOTE: These instructions are best

followed with the fresh food door

removed. See How to Remove the

Hinges, Door and Drawer for

instructions.

ENGLISH ESPAÑOL FRANÇAIS

To avoid electrical shock, which can

cause severe personal injury or

death, observe the following:

➢ Disconnect power to refrigerator

before removing doors. Connect

power only after replacing doors.

WARNING

To avoid damage to walls and

flooring, protect soft vinyl or other

flooring with cardboard, rugs, or other

protective material.

CAUTION

How to remove the

hinges, door and

drawer

Some installations require door removal

to get refrigerator into final location.

1. Unplug power cord

from power source.

2. Remove top hinge

covers by removing

Phillips screws.

➢ Retain screw and

cover for replacement.

3. Unscrew

⁄16" hex head screws from

top hinge to remove hinge.

➢ Retain all screws for later use.

4. Lift refrigerator door from center

hinge pin.

5. Remove center hinge

pin with a

⁄16" hex head

driver.

➢ Retain hinge pin for

later use.

6. Remove Phillips

screws to remove

center hinge.

➢ Retain all screws

for later use.

To avoid possible injury, product, or

property damage, you will need two

people to perform the following

instructions.

CAUTION

10. Lift top of door to unhook door

supports from rail system. Lift door

out to remove.

11. Remove toe grille and bottom

bracket covers.

7. Pull drawer open to full extension.

8. Remove lower basket by pressing

inward on basket sides, then lift

basket.

9. Pull upper basket out to full

extension, and lift out to remove.

12. Remove both stabilizing brackets

with

⁄8" hex head driver.

➢ Retain screws for later use.

Press Tab Here

How to replace the

hinges, door and

drawer

1. Install stabilizing brackets with

⁄8" hex

head driver.

2. Replace toe grille and bottom bracket

covers.

➢ Snap bottom portion into place

first. Press down on top part of

grille until top portion snaps into

place.

3. Pull both rails out to full extension.

Installing your refrigerator,

cont.

7. Install center hinge with Phillips

screws.

8. Install center hinge pin with

⁄16" hex

head driver.

➢ Replace any applicable door

shims.

➢ Make sure the hinge pin is

installed tightly.

9. Install top hinge loosely with

⁄16" hex

head screws.

10. Place hinge side of refrigerator door

on center hinge pin.

11. While holding refrigerator door

upright, tighten door top hinge with

⁄16" hex head driver.

12. Replace top hinge cover on hinge.

4. Hook door supports into rail tabs, as

illustrated, and lower door into final

position.

5. With drawer pulled out to full

extension, insert lower basket by

aligning tabs on both side of lower

basket with notches in rail assembly.

6. Slide upper basket into refrigerator.

Make sure that rear of basket hooks

behind rail catch.

To avoid possible injury and damage

to property:

➢ DO NOT remove sub cap when

removing door trim.

➢ Place doors on nonabrasive

surface protected by towels or rugs

while working directly on door.

CAUTION

* Fasteners may require either a T-15 Torx

driver or a Phillips screwdriver.

Torx

is a registered trademark of Textron Inc.

How to reverse the door

1. Perform all steps listed in How to

Replace the Hinges, Door and

Drawer (page 8).

2. Transfer cabinet

plugs and screws to

opposite side of

cabinet.

➢ Remove plugs with flat blade of

screwdriver wrapped in masking

tape.

➢ Remove center mullion screws

with

⁄16" hex head driver.

3. Remove door stop

from fresh food

door with Phillips

screwdriver.

4. Remove bottom door trim by

removing 4 Phillips screws. Lift

handle corner of trim and slide

toward hinge edge of door.

5. Remove top door trim by removing 4

screws*. Lift handle corner of trim

and slide toward hinge edge of door.

➢ Retain all screws for later use.

6. Reverse handle by removing two

screws* from top and bottom edge of

handle and reattaching handle on

opposite side of door.

7. Install top door trim on bottom side

of door, and bottom trim on top side

of door.

➢ Locate hinge hole corner of trim.

Install hinge hole corner of trim on

hinge side first, then install handle

edge of trim.

8. Proceed to How to Replace the

Hinges, Door and Drawer.

ENGLISH FRANÇAIS ESPAÑOL

How to connect the

water supply

To reduce the risk of injury or

death, follow basic precautions,

including the following:

➢ Read all instructions before

installing device.

➢ DO NOT attempt installation if

instructions are not understood or

if they are beyond personal skill

level.

➢ Observe all local codes and

ordinances.

➢ DO NOT service device unless

specifically recommended in Use

and Care Guice or published

user-repair instructions.

➢ Disconnect power to refrigerator

prior to installing device.

WARNING

To avoid property damage or

possible injury, follow basic

precautions, including the

following:

➢ Consult a plumber to connect

copper tubing to household

plumbing to assure compliance

with local codes and ordinances.

➢ Confirm water pressure to water

valve is between 20 and 100

pounds per square inch. If water

filter is installed, water pressure to

water valve must be a minimum of

35 pounds per square inch.

➢ DO NOT use a self-piercing, or

⁄16"

saddle valve! Both reduce water

flow, become clogged with time,

and may cause leaks if repair is

attempted.

➢ Tighten nuts by hand to prevent

cross threading. Finish tightening

nuts with pliers and wrenches. Do

not overtighten.

➢ Wait 24 hours before placing

refrigerator into final position to

check and correct any water leaks.

CAUTION

MATERIALS NEEDED

➢

⁄4" outer diameter flexible copper

tubing

➢ Brass compression nut and sleeve for

⁄4" outer diameter copper tubing.

➢ Shut-off valve (requires a

⁄4" hole to

be drilled into water supply before

valve attachment)

➢ Adjustable wrench

➢

⁄4" hex nut driver

NOTE: Add 8' to tubing length needed to

reach water supply for creation of

service loop.

1. Create service loop with tubing using

care to avoid kinks in tubing.

2. Remove plastic cap from water valve

inlet port.

3. Place brass nut (A) and sleeve (B) on

copper tube end as illustrated.

4. Place end of copper tubing into water

valve inlet port. Shape tubing slightly –

DO NOT KINK – so that tubing feeds

straight into inlet port.

5. Slide brass nut over sleeve and

screw nut into inlet port. Tighten nut

with wrench.

IMPORTANT: DO NOT overtighten.

Cross threading may occur.

6. Pull on tubing to confirm connection

is secure. Connect tubing to frame

with water tubing clamp (C) and turn

on water supply. Check for leaks and

correct, if present.

7. Monitor water connection for 24

hours. Correct leaks, if necessary.

Installing your refrigerator,

cont.

How to level your

refrigerator

If your refrigerator requires an ice maker

water supply connection, proceed to

How to Connect the Water Supply

section (page 9) before leveling your

refrigerator.

To protect personal property or

refrigerator from damage, observe the

following:

➢ Protect soft vinyl or other flooring

with cardboard, rugs, or other

protective material.

➢ Do not use power tools when

performing leveling procedure.

CAUTION

MATERIALS NEEDED

➢

⁄8" hex head driver

➢ Level

1. Remove toe grille and bottom bracket

covers.

2. Turn left and right

adjustment screws

(A) to raise or

lower front of

refrigerator.

➢ Make sure

refrigerator

cabinet is level from side to side

by adjusting left and right roller

adjustment screws.

➢ Turn stabilizing leg clockwise until

firmly against floor.

3. After completing the above listed

steps, turn roller adjustment screws

(A) 2 to 3 times counterclockwise, so

that full weight of refrigerator rests on

stabilizing legs.

4. Using a level, make sure front of

refrigerator is

⁄4" (6 mm) or

⁄2 bubble

higher than back of refrigerator.

➢ See step 3 for assistance.

5. Replace toe grille and bracket covers.

See markings on inside of toe grille to

insure proper placement.

➢ Snap bottom portion into place

first. Press down on top part of

grille until top portion snaps into

place.

ENGLISH FRANÇAIS ESPAÑOL

Setting and maintaining proper temperatures

The controls are located at the top front of the refrigerator and freezer compartments. NOTE: The freezer control turns the cooling

system on. Neither section will cool if freezer control is set to OFF.

Refrigerator Control

Freezer Control

Initial control settings

1. Locate refrigerator control at the top

of fresh food compartment and

freezer control at top of freezer

section.

2. The manufacturer’s recommended

setting for both compartments is 4.

3. Let the refrigerator run at least 8 to

12 hours before adding food.

4. Allow 24 hours for temperature to

stabilize.

Adjusting the controls

➢ 24 hours after adding food, you may

decide that one or both

compartments should be colder or

warmer. If so, adjust the control(s) as

indicated in the Temperature Control

Guide.

➢ Do not change either control more

than one number at a time.

➢ Allow 5-8 hours for temperatures to

stabilize.

➢ Changing either control will have

some effect on the temperature of the

other compartment.

TEMPERATURE CONTROL GUIDE

Refrigerator too warm Turn the refrigerator control to next higher number.

Refrigerator too cold Turn the refrigerator control to next lower number.

Freezer too warm Turn the freezer control to next higher number.

Freezer too cold Turn the freezer control to next lower number.

To turn refrigerator OFF Turn the freezer control to OFF.

NOTE: Turning freezer control to OFF stops cooling in both compartments. It does

not shut off power to the refrigerator.

Fresh food storage

➢ The fresh food compartment of a

refrigerator should be kept between

34° F and 40° F with an optimum

temperature of 37° F. To check the

temperature, place an appliance

thermometer in a glass of water and

place in the center of the refrigerator.

Check after 24 hours. If the

temperature is above 40° F adjust the

control as explained above.

Frozen food storage

➢ The freezer compartment of a

refrigerator should be kept at

approximately 0° F. To check the

temperature, place an appliance

thermometer between the frozen

packages and check after 24 hours. If

the temperature is above 0° F, adjust

the control as described above.

About your water filter…

Water filter installation

and removal

To avoid serious illness or death, do

not use refrigerator where water is

unsafe or of unknown quality without

adequate disinfection before or after

use of filter.

WARNING

➢ Bypass cartridge DOES NOT filter

water. Be sure to have

replacement cartridge available

when filter change is required.

➢ If water filtration system has been

allowed to freeze, replace filter

cartridge.

➢ If system has not been used for

several months, and water has an

unpleasant taste or odor, flush

system by dispensing 2–3 glasses

of water. If unpleasant taste or

odor persists, change filter

cartridge.

CAUTION

INSTALLING

WATER FILTER

1. Remove blue bypass cap and retain

for possible later use.

2. Remove sealing label from end of

filter and insert into filter head.

3. Rotate gently clockwise until filter

stops, and snap filter cover closed.

4. Reduce water spurts by flushing air

from system. Run water continuously

for 2 minutes through dispenser until

water runs steady.

➢ Additional flushing may be

required in some households

where water is of poor quality.

REPLACING

WATER FILTER

IMPORTANT: Air trapped in system

may cause water and cartridge to eject.

Use caution when removing.

1. Turn filter counterclockwise until it

releases from filter head.

2. Drain water from filter into sink, and

dispose in normal household

garbage.

3. Wipe up excess water in filter cover

and continue with Installing Water

Filter, steps 2 and 3.

WHEN DO I CHANGE THE

WATER FILTER?

The filter should be changed

approximately every 6 months.

IMPORTANT: Condition of water and

amount used determines life span of

water filter cartridge. If water use is

high, or if water is of poor quality,

replacement may need to take place

more often.

HOW DO I ORDER A

REPLACEMENT FILTER

CARTRIDGE?

Kenmore

replacement water filter

cartridge model 9005 is available

through Sears dealers and servicers.

You may also order through Sears by

using the information on the back cover.

I'M TRYING TO DISPENSE

WATER TO FLUSH THE

SYSTEM. WHERE'S THE

WATER?

During initial use, allow about a 1 to 2

minute delay in water dispersal to allow

internal water tank to fill.

WHAT IF I CHOOSE NOT

TO USE THE WATER

FILTRATION SYSTEM?

Dispenser feature may be used without

water filter cartridge. If you choose this

option, replace filter with blue bypass

cap.

ENGLISH FRANÇAIS ESPAÑOL

GENERAL USE

CONDITIONS

Read this Performance Data Sheet and

compare the capabilities of this

refrigerator with your actual water

treatment needs.

DO NOT use this product where water

is microbiologically unsafe or of

unknown quality without adequate

disinfection installed before or after

filtration system. Systems certified

for cyst reduction may be used on

disinfected water that may contain

filterable cysts.

Use only with cold water supply.

Check for compliance with the state

and local laws and regulations.

The retractable water filtration system

uses a 9005 replacement cartridge (see

Sears contact information at the back of

your Use and Care Guide to order).

Timely replacement of filter cartridge is

essential for performance satisfaction

from this filtration system. Please refer

to the applicable section in this Use and

Care Guide for general operation,

maintenance requirements and

troubleshooting.

This system has been tested according

to ANSI/NSF 42 and 53 for reduction of

the substances listed below. The

concentration of the indicated

substances in water entering the system

was reduced to a concentration less than

or equal to the permissible limit for water

leaving the system, as specified in

ANSI/NSF 42 and 53.

*Tested using a flow rate of 0.75 GPM (2.83 L/min.) and a maximum pressure of 120 psi (827 kPa)

under standard laboratory conditions, however, actual performance may vary. Health Claim

Performance tested and certified by NSF International

** Particle size range classification of test. Particles used were 0.5 –1 microns.

Influent Challenge Effluent Average % Maximum Min. Required Inlet

Substance Concentration Average Reduction Effluent Reduction pH

Lead 0.15 mg/L +/- 10% 0.001 mg/L 99.33% 0.001 mg/L 0.010 mg/L 6.5

Lead 0.15 mg/L +/- 10% 0.002 mg/L 98.66% 0.003 mg/L 0.010 mg/L 8.5

Cyst Minimum 50,000/L 1count/mL 99.99% 3 count/mL > 99.95% NA

Turbidity 11+/-1 NTU 0.12 NTU 98.98% 0.18 NTU 0.5 NTU NA

Lindane 0.002 mg/L +/- 10% 0.00005 mg/L 97.62% 0.00005 mg/L 0.00002 mg/L NA

Atrazine 0.009 mg/L +/- 10% 0.0002 mg/L 97.93% 0.0006 mg/L 0.003 mg/L NA

Chlorine 2.0 mg/L +/- 10% 0.09 mg/L 95.26% 0.17 mg/L ≥75% NA

Particulate** at least 10,000 900 count/mL 99.68% 2400 count/mL ≥85% NA

particles/mL

2,4-D 0.210 mg/L +/- 10% 45.45 ug/L 84.42% 100 ug/L 0.0017 mg/L NA

Asbestos

to 10

fibers/L; fibers greater

0.16 MFL/mL 99.96% 0.16 MFL/mL 99% NA

than 10 micrometers in length

PERFORMANCE DATA

Water filter data

SYSTEM SPECIFICATION AND PERFORMANCE DATA

SHEET REFRIGERATOR WATER FILTER CARTRIDGE

MODEL 9005

Specifications

Service Flow Rate (maximum) ...............................................0.75 GPM (2.83 L/min)

Rated Service Life Model 9005 (maximum)...........................500 gallons/1892 liters

Maximum Operating Temperature..........................................100° F/38° C

Minimum Operating Temperature...........................................33° F/1° C

Minimum Pressure Requirement............................................35 psi/138 kPa

Maximum Operating Pressure ...............................................120 psi/827 kPa

1000 Apollo Road

Eagan, Minnesota U.S.A.

EPA EST #35917-MN-1

Standard No. 53: Health Effects

Chemical Reduction Unit

Lead, Atrazine, Lindane and 2, 4-D Reduction

Mechanical Filtration Unit

Cyst, Turbidity and Asbestos Reduction

Tested and certified by NSF International against ANSI/NSF Standards 42 and 53 in

models WF50-KNI300 and WF50-KWI500 for the reduction of:

Standard No. 42: Aesthetic Effects

Taste and Odor Reduction

Chlorine Reduction

Mechanical Filtration Unit

Particulate Reduction Class 1

Door storage

DAIRY CENTER

The Dairy Center

provides convenient

storage for items

such as butter,

yogurt, cheese, etc.

This compartment is an adjustable

feature located in the door. It can be

moved to several different locations to

accommodate storage needs.

➢ To remove, open dairy door, pull

upward and tilt out.

➢ To install, reverse above procedure.

DOOR BUCKETS

Door Buckets adjust to

meet individual storage

needs.

➢ To remove,

slide bucket up

and pull

straight out.

➢ To install, reverse above procedure.

Fresh food features

Water dispenser

A Water Dispenser

is located on the

left side wall of the

fresh food section.

This design is for

cold water

dispensing only.

To dispense

water:

➢ Hold container under spout and press

dispenser pad, as illustrated.

Interior shelves

To avoid personal injury or property

damage, observe the following:

➢ Confirm shelf is secure before

placing items on shelf.

➢ Handle tempered glass shelves

carefully. Shelves may break

suddenly if nicked, scratched, or

exposed to sudden temperature

change.

CAUTION

SPILLPROOF SHELVES

Spillproof Shelves hold

simple spills for easier

cleaning.

➢ To remove shelves, lift

up and out.

➢ To install shelves, reverse above

procedure.

Spillproof Slide-out

Shelves feature

the convenience

of easy cleaning

with a pullout

design to reach items in the back. For

ease of cleaning, glass shelf may be

removed by pulling to full extension and

lifting out of frame.

DOOR RETAINER

Door Retainers remove for easy

cleaning.

➢ To remove, slide retainer up and pull

straight out.

➢ To install, reverse above procedure.

ENGLISH FRANÇAIS ESPAÑOL

Climate-controlled

drawers

HUMIDITY-CONTROLLED

CRISPER DRAWERS

The Crisper Drawer keeps produce

fresh longer by providing an

environment with adjustable humidity.

Controls

The

crisper

controls

regulate

the amount of humidity in the crisper

drawer. Use the low setting for produce

with outer skins. Use the high setting for

leafy produce.

To remove and install crisper

drawers:

➢ To remove

drawer, pull

drawer out to full

extension. Tilt up

front of drawer and pull straight out.

➢ To install, insert drawer into frame

rails and push back into place.

WHAT CAN I DO TO PROLONG

THE LIFE OF MY PRODUCE?

Please observe the following rules when

storing produce in humidity-controlled

crisper drawers:

➢ DO NOT wash produce before

placing in crispers. Any additional

moisture added to the drawers may

cause produce to prematurely spoil.

➢ DO NOT line crispers with paper

towels. Towels will retain moisture.

➢ Follow control instructions carefully.

Not setting controls correctly may

damage produce.

See below for correct humidity drawer

control settings:

LOW • cauliflower • apples

• corn • oranges

• zucchini • grapes

• cucumbers

HIGH • lettuce • asparagus

• spinach • cabbage

• celery • broccoli

• fresh sprouts • fresh herbs

HOW DO I REMOVE THE GLASS

AND CRISPER FRAME IF I WANT

TO CLEAN IT?

➢ Remove the drawers as instructed.

➢ Place hand beneath frame to push up

glass from underneath. Lift glass out.

➢ Lift frame from refrigerator liner rails.

➢ To install, replace frame on liner rails

and insert glass into grooves on top

of frame.

STORAGE DRAWER

The Storage Drawer can be used for

large party trays, deli items or

beverages.

To remove and install drawer:

➢ To remove drawer, pull drawer out to

full extension. Tilt up front of drawer

and pull straight out.

➢ To install, insert drawer into frame

rails and push back into place.

Freezer features

Automatic ice maker

Using Ice Maker for the First Time

1. Confirm ice bin is in

place and ice maker

arm is down.

2. After freezer section reaches

between 0° to 2° F (-18° to -17° C),

ice maker fills with water and begins

operating.

3. Allow approximately 24 hours after

installation to receive first harvest of

ice.

4. Discard ice created within first 12

hours of operation to verify system is

flushed of impurities.

To avoid property damage, observe

the following:

➢ Do not force ice maker arm down

or up.

➢ Do not place or store anything in

ice storage bin.

CAUTION

To prevent accidental child

entrapment or suffocation risk, DO

NOT remove the divider in the top

freezer basket.

DANGER

Drawers

PULLOUT DRAWER

BASKETS

(Door assembly of drawer removed from

illustration for visual clarity)

To remove and replace baskets:

➢ See page 7 for basket removal and

page 8 for replacement instructions.

Operating Instructions

1. Confirm ice bin is in place and ice

maker arm is down.

2. After freezer section reaches 0° to 2° F

(-18° to -17° C), ice maker fills with

water and begins operating. You will

have a complete harvest of ice

approximately every 3 hours.

3. Stop ice production

by raising ice maker

arm until click is

heard.

4. Ice maker will remain in the off

position until arm is pushed down.

ENGLISH FRANÇAIS ESPAÑOL

Hints and care

PART DO

➢ Use 4 tablespoons of baking soda dissolved in 1 quart

(1 liter) warm soapy water.

➢ Rinse surfaces with clean warm water and dry immediately

to avoid water spots.

➢ Use warm, soapy water and a soft, clean cloth or sponge.

➢ Rinse surfaces with clean warm water and dry immediately

to avoid water spots.

➢ Use a vacuum cleaner hose nozzle.

➢ Use a vacuum cleaner hose nozzle with brush attachment.

➢ Follow removal and installation instructions from appropriate

feature section.

➢ Allow items to adjust to room temperature.

➢ Dilute mild detergent and use a soft clean cloth or sponge

for cleaning.

➢ Use a plastic bristle brush to get into crevices.

➢ Rinse surfaces with clean warm water.

➢ Dry glass and clear items immediately to avoid spots.

DO NOT USE

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Vinegar-based products

➢ Citrus-based cleaners

➢ Abrasive or harsh cleaners

➢ Metal or plastic-textured

scouring pads

➢ A dishwasher

Textured Doors

and Exterior

Cabinet Interior

Stainless Steel Doors

and Exterior*

IMPORTANT: Damage

to stainless steel finish

due to improper use of

cleaning products or

non-recommended

products is not covered

under this product’s

warranty.

Door Gaskets

Condenser Coil

Remove base grille to

access

Condenser Fan Outlet

Grille

See back of refrigerator

Accessories Shelves,

buckets, drawers, etc.

To avoid personal injury or property damage, observe the following:

➢ Read and follow manufacturer’s directions for all cleaning products.

➢ DO NOT place buckets, shelves or accessories in dishwasher. Cracking or

warping of accessories may result.

CAUTION

To avoid electrical shock which can

cause severe personal injury or

death, disconnect power to

refrigerator before cleaning. After

cleaning, connect power.

WARNING

How to clean your refrigerator

*Astainless steel cleaner has been included inside the refrigerator for your use. To purchase additional cleaner, please contact

Sears using the information on the back of your guide.

How to remove odors

from refrigerator

1. Remove all food.

2. Disconnect refrigerator.

3. Clean the following items–paying

special attention to crevices–using

the appropriate instructions in How to

Clean Your Refrigerator:

•Walls, floor and ceiling of cabinet

interior.

• Drawers, shelves and gaskets.

4. Wash and dry all bottles, containers

and jars. Discard spoiled or expired

items.

5. Wrap or store odor-causing foods in

tightly-sealed containers to prevent

reoccurring odors.

6. Connect power to refrigerator and

return food.

7. After 24 hours, check if odor has

been eliminated.

If odor is still present...

1. Remove drawers and place on top

shelf of refrigerator.

2. Pack refrigerator and freezer

sections–including doors–with

crumpled sheets of black and white

newspaper.

3. Place charcoal briquettes randomly

on crumpled newspaper in both

freezer and refrigerator

compartments.

4. Close doors and let stand 24–48 hours.

5. Repeat steps 5 through 7 above.

If odor was not eliminated, contact

Sears Service Center. Refer to back of

manual for phone number.

Energy saving ideas

➢ Avoid overcrowding refrigerator

shelves. This reduces effectivity of air

circulation around food and causes

refrigerator to run longer.

➢ Avoid adding too much warm food to

refrigerator at one time. This

overloads compartments and slows

rate of cooling.

➢ Do not use aluminum foil, wax paper,

or paper toweling as shelf liners. This

decreases air flow and causes

refrigerator to run less efficiently.

➢ A freezer that is

⁄3 full runs most

efficiently.

➢ Locate refrigerator in coolest part of

room. Avoid areas of direct sunlight,

or near heating ducts, registers, or

other heat producing appliances. If

this is not possible, isolate exterior by

using a section of cabinet or an

added layer of insulation.

➢ Refer to section in Use and Care

Guide on temperature controls for

recommended control settings.

➢ Clean door gaskets every three

months according to Use and Care

Guide instructions. This will assure

that door seals properly and

refrigerator runs efficiently.

➢ Take time to organize items in

refrigerator to reduce time that door

is open.

➢ Be sure your doors are closing

securely by leveling refrigerator as

instructed in your Use and Care

Guide.

➢ Clean condenser coils off as

indicated in the Use and Care Guide

every 3 months. This will increase

energy efficiency and cooling

performance.

To avoid personal injury or property

damage, observe the following:

➢ Allow light bulb to cool.

➢ Wear gloves when replacing light

bulb.

CAUTION

To avoid electrical shock which can

cause severe personal injury or

death, disconnect power to

refrigerator before replacing light

bulb. After replacing light bulb,

connect power.

WARNING

How to remove and

replace light bulbs

FRESH FOOD

1. Slide shield toward

back of

compartment to

release from light

assembly.

2. Remove light bulbs.

3. Replace with appliance bulbs no

greater than 40 watts.

4. Replace light bulb

cover by inserting

tabs on light shield

into liner holes on

each side of light assembly. Slide

shield toward front of refrigerator until

it locks into place. DO NOT force

shield beyond locking point. Doing so

may damage light shield.

FREEZER

1. Pinch rear tabs on

light cover and pull

straight down.

2. Remove light

bulb.

3. Replace bulb with

appliance bulb no greater than 40

watts.

4. Insert front tabs of light cover into

freezer liner and snap rear portion

over light assembly until rear tabs

engage.

Hints and care,

cont.

ENGLISH FRANÇAIS ESPAÑOL

Normal operating sounds

Today’s refrigerators use foam insulation and are more energy efficient than refrigerators of the past. However, foam insulation is

not as sound absorbent as former insulated models. As a result, certain sounds may be unfamiliar. In time, these sounds will

become familiar. Please refer to this information before calling service.

SOLUTION

➢ Normal operation

➢ See Installation Instructions for details on how to level your

refrigerator.

➢ Normal operation

➢ Stop sound by raising ice maker arm to ‘off’ position. See

Automatic Ice Maker section in your Use and Care Guide

for details.

➢ Normal operation

POSSIBLE CAUSE

➢ Freezer control (A) clicks when

starting or stopping compressor.

➢ Defrost timer (B) sounds like an

electric clock and snaps in and

out of defrost cycle.

➢ Freezer fan (C) and condenser

fan (D) make this noise while

operating.

➢ Evaporator (E) and heat

exchanger (F) refrigerant makes

this noise when flowing.

➢ Ice cubes from ice maker (select

models) drop into ice bucket (G).

➢ Compressor (H) makes a

pulsating sound while running.

➢ Refrigerator is not level.

➢ Ice maker water valve (I)

hookup (select models) buzzes

when ice maker fills with water.

➢ Ice maker (J) is in the ‘on’

position without water

connection.

➢ Compressor (H) can make a high-

pitched hum while operating.

➢ Defrost heater (K) hisses, sizzles

or pops when operational.

TOPIC

Clicking

Air rushing or whirring

Gurgling or boiling

sound

Thumping

Vibrating noise

Buzzing

Humming

Hissing or

popping

PROBLEM

Food temperature

appears too warm

Refrigerator has an odor

Water droplets form on

outside of refrigerator

Water droplets form on

inside of refrigerator

Refrigerator or ice maker

make unfamiliar sounds

or seems too loud

Crisper drawers do not

close freely

Refrigerator runs too

frequently

Operation

POSSIBLE CAUSE

Door is not closing properly.

Controls need to be adjusted.

Condenser coils are dirty.

Rear air grille is blocked.

Door has been opened frequently, or has

been opened for long periods.

Food has recently been added.

Compartment is dirty or has odor-causing

food.

Check gaskets for proper seal.

Humidity levels are high.

Controls require adjustment.

Humidity levels are high or door has been

opened frequently.

Check gaskets for proper seal.

Normal operation.

Contents of drawer, or positioning of items in

the surrounding compartment could be

obstructing drawer.

Drawer is not in proper position.

Refrigerator is not level.

Drawer channels are dirty or need treatment.

Doors have been opened frequently or have

been opened for long periods of time.

Humidity or heat in surrounding area is high.

Food has recently been added.

Refrigerator is exposed to heat by

environment or by appliances nearby.

Condenser coils are dirty.

SOLUTION

See Installing Your Refrigerator–How to Level Your

Refrigerator section on how to properly level refrigerator.

Check gaskets for proper seal. Clean, if necessary, according

to cleaning instructions.

Check for internal obstructions that are keeping door from

closing properly (i.e. improperly closed drawers, ice buckets,

oversized or improperly stored containers or foodstuffs, etc.)

See Setting and Maintaining Proper Temperatures–

Adjusting the Controls section on how to adjust your controls.

See section on Hints and Care–How to Clean Your

Refrigerator for instructions.

Check the positioning of food items in refrigerator to make

sure grille is not blocked. Rear air grilles are located under

crisper drawers.

Reduce time door is open. Organize food items efficiently to

assure door is open for as short a time as possible.

Allow interior environment to adjust for period the door has

been open.

Allow time for recently added food to reach refrigerator or

freezer temperature.

See section on Hints and Care for instructions.

See section on Hints and Care–How to Clean Your

Refrigerator for instructions.

See Setting and Maintaining Proper Temperatures–

Adjusting the Controls section on how to adjust your controls.

See Setting and Maintaining Proper Temperatures–

Adjusting the Controls section on how to adjust your controls.

See Setting and Maintaining Proper Temperatures–

Adjusting the Controls section on how to adjust your controls.

Reduce time door is open. Organize food items efficiently to

assure door is open for as short a time as possible.

See section on Hints and Care–How to Clean Your

Refrigerator for instructions.

Refer to Normal Operating Sounds.

Reposition food items and containers to avoid interference

with the drawers.

See section on Fresh Food Features–Climate-Controlled

Drawers to verify drawer positioning.

See Installing Your Refrigerator–How to Level Your

Refrigerator section on how to properly level refrigerator.

Clean drawer channels with warm, soapy water. Rinse and

dry thoroughly. Apply a thin layer of petroleum jelly to drawer

channels.

Reduce time door is open. Organize food items efficiently to

assure door is open for as short a time as possible.

Allow interior environment to adjust for period the door has

been open.

Normal operation.

Allow time for recently-added food to reach refrigerator or

freezer temperature.

Evaluate your refrigerator’s environment. Refrigerator may

need to be moved to run more efficiently.

See section on Hints and Care–How to Clean Your

Refrigerator for instructions.

Troubleshooting

La page charge ...

Kenmore Elite 59672282201 Le manuel du propriétaire

Marque: Kenmore Elite

Modèle: 59672282201

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore Elite 59672282201 Owner's manual
español: Kenmore Elite 59672282201 El manual del propietario

Kenmore Elite 59672282201 Le manuel du propriétaire

Ce manuel convient également à

Kenmore Elite 59672282201 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents