Ohaus ST300-G Manuel utilisateur

STARTER 300

Portable pH Meter

Instruction Manual

Manual de instrucciones

del pHmetro portátil

STARTER 300

PH-mètre portable

Manuel d’instructions

STARTER 300

Medidor de pH Portátil

Manual de Instruções

TABLE OF CONTENTS

1 INTRODUCTION ................................................................... 1

1.1 Definition of Signal Warnings and Symbols ...................................... 1

1.2 Safety Precautions ............................................................................ 2

1.3 Display and controls .......................................................................... 3

2 INSTALLATION ..................................................................... 5

2.1 Package contents .............................................................................. 5

2.2 Installing the batteries ....................................................................... 6

2.3 Installing the electrode clip ................................................................ 6

2.4 Installing the IP54 seal components ................................................. 6

2.5 Integrated stand for table top use ..................................................... 7

3 STARTER 300 SETUP .......................................................... 8

3.1 Set temperature unit and MTC value ................................................ 8

3.2 Selecting a predefined buffer group .................................................. 8

4 STARTER 300 OPERATION ................................................. 9

4.1 Calibration ......................................................................................... 9

4.1.1 Buffer group ................................................................................ 9

4.1.2 Performing 1-point calibration .................................................. 10

4.1.3 Performing 2-point calibration ................................................... 11

4.2 Sample measurement ..................................................................... 12

4.2.1 pH measurement ...................................................................... 12

4.2.2 mV measurement ..................................................................... 12

4.3 Temperature measurement ............................................................. 12

4.4 Using the memory ........................................................................... 12

4.4.1 Storing a reading ...................................................................... 12

4.4.2 Recalling from memory ............................................................ 12

4.4.3 Clearing the memory ................................................................ 12

5 MAINTENANCE .................................................................. 14

5.1 Error message ................................................................................. 14

5.2 Meter maintenance.......................................................................... 14

5.3 Electrode maintenance ................................................................... 14

5.4 Self-diagnosis .................................................................................. 15

5.5 Recover factory settings .................................................................. 15

6 TECHNICAL DATA ............................................................. 16

6.1 Specifications ................................................................................ 16

6.2 Compliance ..................................................................................... 16

7 BUFFER GROUP ................................................................ 18

STARTER 300 Portable pH Meter EN-1

1 INTRODUCTION

Thank you for choosing OHAUS.

Please read the manual completely before using the STARTER 300 portable pH meter to avoid

incorrect operation.

STARTER 300 has an excellent performance/price ratio and is designed with many useful features.

Other accessories such as different electrodes for different applications, bottle buffer solutions are

also available from OHAUS.

Starter 300 offers many practical features such as:

 Ergonomic, multifunctional design for ambidextrous measurements or table top use

 Integrated table top stand for counter use and semi-permanent installations

 Integrated labeling design for quick product identification

 IP54 protection against dust and water

 Ohaus renowned user friendly software

1.1 Definition of Signal Warnings and Symbols

Safety notes are marked with signal words and warning symbols. These show safety issues and

warnings. Ignoring the safety notes may lead to personal injury, damage to the instrument,

malfunctions and false results.

Signal Words

WARNING For a hazardous situation with medium risk, possibly resulting in

injuries or death if not avoided.

CAUTION For a hazardous situation with low risk, resulting in damage to the

device or the property or in loss of data, or injuries if not avoided.

Attention For important information about the product.

Note For useful information about the product

Warning Symbols

General hazard

Explosion hazard

Corrosive hazard



Alternating current



Direct current

EN-2 STARTER 300 Portable pH Meter

1.2 Safety Precautions

CAUTION: Read all safety warnings before installing, making connections, or servicing this

equipment. Failure to comply with these warnings could result in personal injury and/or property

damage. Retain all instructions for future reference.

 Use the equipment only in dry locations.

 Dry off any liquid spills immediately. The instrument is not watertight.

 When using chemicals and solvents, comply with the instructions of the chemical producer

and the general lab safety rules.

 Use only approved accessories and peripherals.

 Operate the equipment only under ambient conditions specified in these instructions.

 Do not operate the equipment in hazardous or unstable environments.

 Service should only be performed by authorized personnel.

STARTER 300 Portable pH Meter EN-3

1.3 Display and controls

Displays

1

Electrode condition

Slope: more than 95%

and offset: ± (0-15) mV

Electrode condition is good

Slope: 90-95%

or offset: ± (15-35) mV

Electrode condition is

acceptable

Slope: less than 90%

or offset: ± (>35) mV

Electrode condition is not

good or needs cleaning

2

Endpoint stability icon ; Auto endpoint icon

3

Measurement icon - ; measurement or calibration is running

4

Calibration icon - ; calibration in progress

5

Setup icon - ; instrument is in the setup mode

6

Battery status icon shows the condition of the batteries - fully charged, half-charged or fully

discharged

7

pH/mV reading or slope in calibration process

8

Calibration point / Buffer group /Memory number / Error index

9

Auto temperature compensation - ATC ; Manual temperature compensation - MTC

10

Temperature during measurement or offset in calibration process

2

3

4

1

5

6

7

8

9

10

EN-4 STARTER 300 Portable pH Meter

Controls

Button

Press & release

Press & hold

for 3 seconds

- Start or endpoint measurement

- Confirm setting, store entered

value

- Turn auto endpoint on / off

,

- Start calibration

- Review the latest calibration

data (slope, offset)

- Meter turn on

- Return to measurement screen

- Meter turn off

- Store current reading to memory

- Increase value during setting

- Scroll up through the memory

- Recall stored data

- Switch between pH and mV

measuring modes

- Decrease value during setting

- Scroll down through the memory

- Enter setup mode

- Start self-diagnosis

STARTER 300 Portable pH Meter EN-5

2 INSTALLATION

Carefully unpack the box.

2.1 Package contents

The ST300-B (basic) package has the following items:

In addition to ST300-B content, the ST300 package also includes the following:

Each pH buffer powder should be dissolved in 250ml pure water or deionized water in volumetric

flask.

Additional Ohaus pH electrodes are available for various applications:

Model

Description

P/N

ST310

3-in-1 plastic refillable pH Electrode

83033965

ST210

2-in-1 plastic refillable pH Electrode

83033966

ST320

3-in-1 plastic gel pH Electrode(no need to fill)

83033967

ST230

2-in 1 glass muddy sample pH Electrode

83033968

STORP1

Gel plastic ORP electrode

30038555

STORP2

Refillable glass ORP electrode

30038553

STTEMP30

Temperature Electrode

83033970

Buffers and Accessories:

Buffer powder set (4.01; 7.00; 10.00)

83033971

Buffer pH1.68 250ml

30100424

Buffer pH4.01 250ml

30100425

Buffer pH7.00 250ml

30100427

Buffer pH10.01 250ml

30100429

Buffer pH12.45 250ml

30100430

Portable Bag for portable meters

30031635

ST300-B

Units

STARTER 300

1

AAA battery

4

Electrode Clip

1

IP54 seal components

1 set

Wrist Strap

1

pH Buffer Powder Set (4.01, 7.00, 10.01)

1 set

ST320 3-in-1 gel pH electrode

1

EN-6 STARTER 300 Portable pH Meter

2.2 Installing the batteries

 Remove the battery cover screw using a coin or screwdriver and remove the battery cover.

 Insert the batteries in the battery compartment as shown.

 Replace the battery cover and tighten the battery cover screw.

2.3 Installing the electrode clip

The electrode clip is an electrode holder that can be placed on either side of the housing.

 Attach the clip by inserting the tabs into the recess.

 Slide the clip forward to lock in position.

 Slide the shaft of the sensor into the clip from above.

2.4 Installing the IP54 seal components

Use the small plastic tool as shown to install the seal components:

STARTER 300 Portable pH Meter EN-7

2.5 Integrated stand for table top use

STARTER 300 has an integrated table stand as shown, which can be pushed out to use the meter

on a lab bench or desk. To close the stand, push the middle edge of the stand toward the meter.

EN-8 STARTER 300 Portable pH Meter

3 STARTER 300 SETUP

3.1 Set temperature unit and MTC value

Please note:

If a temperature electrode is used, Automatic Temperature Compensation (ATC) and the sample

temperature are displayed on the screen. You may then choose to skip MTC setup (below).

If the meter does not detect a temperature electrode or one is not used, the meter automatically

switches to Manual Temperature Compensation (MTC) mode and MTC appears on the screen.

MTC can be set as follows:

 Power the meter on by pressing

 Press and hold until the setup icon appears on the display and the current

temperature unit blinks (°C or °F).

 Press or to switch between °C and °F .

 Press to confirm your selection.

Then

 Continue with MTC temperature setting by using or to adjust temperature

compensation accordingly

 Press button- to confirm the setting

 Press to return to the measurement screen.

The default MTC temperature value setting is 25 °C (77°F).

Note: °C = 5/9 (°F - 32)

3.2 Selecting a predefined buffer group

After confirming the MTC value (or if you are using ATC) you have the option of making a buffer

group selection. In most cases the default buffer group will be used, buffer group b1.

If it is necessary to switch the buffer group, use button- or button- to select a buffer

group among 4 buffer groups shown in section 4.1.1 in this manual. Press button- to confirm

the setting or press button- to return to the measurement screen.

The default buffer group is b1.

b1

1.68

4.01

7.00

10.01

STARTER 300 Portable pH Meter EN-9

4 STARTER 300 OPERATION

The basic procedure for pH measurement is as follows:

a) pH electrode preparation

b) buffer preparation and pH electrode calibration

c) sample preparation

d) pH measurement

e) Record measurement results

f) Rinse the pH electrode and store properly

For pH electrode preparation: pH electrode should be rinsed with pure water before and after

using. Check if the electrode is physically damaged. (Be careful with the glass bulb)

The pH electrode should be stored in the included storage bottle; the solution in the bottle is 3M

KCl. After placing pH electrode into the sample or buffer solution, carefully stir with the electrode

for several seconds then wait 30 to 60 seconds for the signal to be stabilize, and then press the

button to operate (Calibration or measurement).

WARNING Do not operate the equipment in hazardous environments. The

equipment is not explosion protected.

WARNING When using chemicals and solvents, comply with the instructions of the

chemical producer and the general lab safety rules.

STARTER 300 will turn off the power automatically without any press operation after 10 minutes.

4.1 Calibration

4.1.1 Buffer group

STARTER 300 can perform 1-, 2- or 3- point calibrations.

There are 4 buffer groups in the meter, you can select the buffer group you prefer (see 4.3),

default buffer group is b1 (US standard), and the buffer value will be automatically recognized

during calibration.

The 4 predefined buffer groups are (at 25°C):

STARTER 300 automatically corrects for the temperature dependence of the buffer pH values

given in the following table - buffer group b1.

b1

1.68

4.01

7.00

10.01

b2

2.00

4.01

7.00

9.21

11.00

b3

1.68

4.00

6.86

9.18

12.46

b4

1.68

4.01

6.86

9.18

EN-10 STARTER 300 Portable pH Meter

pH electrodes need to be calibrated with pH standard buffer solution before a proper pH

measurement can be made. Calibration is to display the correct pH value when meter receives

the mV value signal from the pH electrode.

Slope: the linear coefficient between mV and pH according to theoretical value (e.g. -

59.16mV/pH @ 25°C which means 100% slope);

Offset: the mV value when pH value is 7.00. (Theoretical value is 0 mV);

4.1.2 Performing 1-point calibration

When performing calibration, Ohaus recommends using Auto End Point Mode. After powering

the meter on, be sure the top of the screen shows to ensure the meter is in Auto End point

Mode.

Auto or Manual End point Mode:

o Press and hold to change the End Point Mode.

o When in Manual Mode, to manually reach a pH measurement or calibration value,

you need to press button- when reading is stable and displays : then the

sample reading or calibration value freezes, blinks 3 times and freezes on

the display.

o When in Auto End Point Mode, the meter determines when the reading is stable

then displays and locks the reading or calibration value automatically, the reading

freezes and blinks 3 times then disappears; blinks 3 times and freezes on

the display.

o Please note stability criterion: the signal of the sensor input may not change by

more than 0.1mV in 6 seconds.

Note: With the 1-point calibration only the offset is adjusted. If the sensor was previously

calibrated with multi-point calibration the previously stored slope will remain. Otherwise theoretical

100% slope (-59.16 mV / pH) will be used.

5 °C

1.67

4.01

7.09

10.25

10 °C

1.67

4.00

7.06

10.18

15 °C

1.67

4.00

7.04

10.12

20 °C

1.68

4.00

7.02

10.06

25 °C

1.68

4.01

7.00

10.01

30 °C

1.68

4.01

6.99

9.97

35 °C

1.69

4.02

6.98

9.93

40 °C

1.69

4.03

6.97

9.89

45 °C

1.70

4.05

6.97

9.86

50 °C

1.71

4.06

6.96

9.83

STARTER 300 Portable pH Meter EN-11

When STARTER 300 is in pH measurement mode (see 4.2) and Auto End point Mode.; place

the pH electrode in your chosen calibration buffer, stir for 10 seconds, and wait 30-60 seconds,

then:

 Press button- . “Cal 1” displays on the bottom left of the screen and “Cal ” is blinking.

and appear on the top of the screen, is blinking during calibration.

 The meter reaches the calibration (e.g. 7.00) value with the temperature display on the

screen.

The 1-point calibration is finished. There are now 3 options (OHAUS recommends conducting at

least a 2 point calibration);

1. Press button- to store the 1-point calibration and exit, the offset and the

slope are shown on the display for 3 seconds then return to the measurement

screen.

2. Press button- to reject the calibration, the meter then returns to the

measurement screen.

3. Rinse pH electrode then put into another buffer, press button- to do the 2-

point calibration.(see 4.1.3)

4.1.3 Performing 2-point calibration

 Perform 1-point calibration as described above.

 Rinse the pH electrode with pure water.

 Place the electrode in the next calibration buffer, stir and wait, then press button- , “Cal

2” displays on the bottom left of the screen and “Cal ” is blinking. and appear on the

top of the screen, is blinking during calibration.

 The meter reaches the calibration (e.g. 4.01) with the temperature display on the screen.

The 2 point calibration is finished. There are now 3 options :

1. Press button- to do the 3-point calibration.

2. Press button- to reject the calibration, the meter then returns to the

measurement screen.

3. Press button- to store the 2-point calibration and exit, the offset and the

slope are shown on the display for 3 seconds then return to the measurement

screen.

Note: To perform a 3 point calibration, follow the instructions for performing a 2 point calibration

using a third buffer.

EN-12 STARTER 300 Portable pH Meter

4.2 Sample measurement

4.2.1 pH measurement

 Place the electrode in the sample, stir for 10 seconds, and wait 30-60 seconds.

 Press button- to start the pH measurement, appears on the display. is blinking

during measurement.

 When meter reaches the proper value, the pH value with the temperature is displayed on the

screen.

4.2.2 mV measurement

 Press button- to switch between pH and mV measurement.

 Follow the same procedure as for pH measurement to perform a mV measurement.

4.3 Temperature measurement

For better accuracy, we recommend to use either a built-in or a separate temperature electrode.

 If a temperature electrode is used, ATC and the sample temperature are displayed.

 If the meter does not detect a temperature electrode, it automatically switches to the manual

temperature compensation mode and MTC appears. MTC temperature should be set. (See

section 3.1 in this manual)

Note: STARTER 300 accepts NTC 30 kΩ temperature sensor.

4.4 Using the memory

4.4.1 Storing a reading

The STARTER 300 can store up to 30 results.

 Press button- when the measurement reaches its final reading, M01 indicates that one

result has been stored.

If you press button- when M30 is displayed, FUL displays to indicate the memory is full. To

store further data you will have to clear the memory. (See 4.4.3 below)

4.4.2 Recalling from memory

 Press and hold button- to recall the stored values from memory when the current

measurement reaches its final reading and freezing.

 Press button- or button- to scroll through the stored results. R01 to R30 indicates

which result is being displayed.

Press button- to exit.

STARTER 300 Portable pH Meter EN-13

4.4.3 Clearing the memory

 Pressing button- or button- to scroll through the stored results until “MRCL”

appears.

 Press button- , CLr blinks;

 There are now two choices:

 Press button- to confirm the deletion of all the stored data.

 Press button- to return to the measurement mode without deleting the memory.

EN-14 STARTER 300 Portable pH Meter

5 MAINTENANCE

5.1 Error message

Error 0

Memory access error

Reset to factory settings

Error 1

Self-diagnosis failed

Repeat the self-diagnosis procedure and make

sure that you finish pressing all five keys within

two minutes.

Error 2

Measured values out of range

Check if the electrode is properly connected and

placed in the sample solution.

Error 3

Measured buffer temperature

out of range (<5 or >40 °C)

Keep the pH buffer temperature within the range

for calibration

Error 4

Offset out of range

offset > 60mV or < - 60 mV

Make sure the pH buffer is correct and fresh;

Clean or replace the pH electrode.

Error 5

Slope out of range

Make sure the buffer is correct and fresh; Clean

or replace the pH electrode.

Error 6

Meter cannot recognize the

buffer

Make sure the buffer is correct and fresh; check if

the buffer has not been used more than once.

Error 9

The current data set has

already been stored once

An endpoint reading can only be stored once.

Perform a new measurement to store.

For further technical support please contact Ohaus. (US please contact 1-800-672-7722)

5.2 Meter maintenance

Never unscrew the two halves of the housing!

The STARTER 300 series instruments do not require any maintenance other than replacement of

depleted batteries. To clean, use a damp cloth.

The housing is made of acrylonitrile butadiene styrene (ABS). This material is susceptible to

damage by some organic solvents, such as toluene, xylene and methyl ethyl ketone (MEK). Any

spillage should be immediately wiped off.

5.3 Electrode maintenance

Make sure the electrode is filled with electrolyte solution. Always store the electrode according to

the electrode instruction manuals and do not allow it to dry out.

If the electrode response becomes sluggish or the slope is not acceptable, try the following:

o Soak the electrode in 0.1M HCl for at least 8 hours.

o For fat or oil contaminant, degrease the membrane with cotton wool soaked in either

acetone or a soap solution.

After electrode treatment, a new calibration should be performed. If the electrode slope is still not

acceptable, the electrode might need to be replaced.

STARTER 300 Portable pH Meter EN-15

5.4 Self-diagnosis

 Press and hold and simultaneously until the meter displays the full screen. Each

icon blinks one after the other.

This checks whether all icons are correctly shown. The next step is to check that the keys are

functioning correctly. This requires user interaction.

When b blinks, five icons are displayed.

 Press the five keys in any order. Each time you press a key an icon disappears from the

screen, continue to press the other keys until all the icons have disappeared.

When the self-diagnosis has been completed successfully, PAS appears. If self-diagnosis fails,

error message Err 1 appears. In this case, repeat the self-diagnosis.

Note: You have to finish pressing all five keys within 2 minutes, otherwise Err 1 appears and you

will have to repeat the procedure.

5.5 Recover factory settings

 When the meter is off, press and hold & & together for 3 seconds, the

screen displays “RST” and blinks, press to reset factory settings (MTC, slope and

offset, etc.).

 Press to switch off the meter.

EN-16 STARTER 300 Portable pH Meter

6 TECHNICAL DATA

6.1 Specifications

Ambient conditions

 Altitude: Up to 2000 m

 Specified Temperature range: 5°C to 40°C

 Humidity: maximum relative humidity 80 % for temperatures up to 30°C decreasing linearly to

50% relative humidity at 40°C

 Installation category: N/A

 Pollution degree: N/A

 Operability is assured at ambient temperatures between 5°C to 40°C

Model

ST300

Measuring range

0.00…14.00 pH

–1999…1999 mV

0 °C…100 °C

Resolution

0.01 pH

1 mV

0.1 °C

Error limits

± 0.01 pH

± 1 mV

± 0.5 °C

Calibration

3 points

4 predefined buffer groups

Memory

30 measurements

Current calibration

Power supply

4 x AAA (LR03) batteries

> 500 operating hours

Size/weight

90 W x 150 D x 35 H mm / 0.18 kg

(without batteries)

Display

Liquid crystal

Input

BNC, impedance > 10e+12 Ω

Cinch, NTC 30 kΩ

Temperature-compensation

ATC & MTC

IP protection

IP54

Housing

ABS

La page charge ...

Ohaus ST300-G Manuel utilisateur

Ce manuel convient également à

Ohaus ST300-G Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents