Maytag MFF2055YEB00 User Instructions

Catégorie
Frigos
Taper
User Instructions

Ce manuel convient également à

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,
please visit our website at www.maytag.com for additional information. If you still need assistance, call us at 1-800-688-9900.
In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.
You will need your model and serial number, located on the inside wall of the refrigerator compartment.
Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de
su producto, visite: www.maytag.com.
Necesitara su nQmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.
Table of Contents / Table des mati res
REFRIGERATOR SAFETY .............................................................. 2
Proper Disposal of Your Old Refrigerator .................................... 2
INSTALLATION INSTRUCTIONS ................................................... 3
Unpack the Refrigerator ............................................................... 3
Location Requirements ................................................................ 3
Remove and Replace Refrigerator Doors and Drawer Front ....... 4
Electrical Requirements ................................................................ 8
Water Supply Requirements ........................................................ 8
Connect the Water Supply ........................................................... 8
Handle Installation ...................................................................... 10
Door Closing and Door Alignment ............................................. 10
FILTERS AND ACCESSORIES ..................................................... 11
Water Filtration System .............................................................. 11
Install Air Filter ............................................................................ 11
Install Produce Preserver ........................................................... 12
Accessories ................................................................................ 13
REFRIGERATOR USE ................................................................... 13
Opening and Closing Doors ....................................................... 13
Using the Controls ...................................................................... 13
Water Dispenser ......................................................................... 15
Ice Maker .................................................................................... 16
REFRIGERATOR FEATURES ....................................................... 16
Refrigerator Shelves ................................................................... 16
Pantry Drawer ............................................................................. 17
Crisper ........................................................................................ 17
DOOR FEATURES ......................................................................... 18
Condiment Bins .......................................................................... 18
Fresh Bin ..................................................................................... 18
Half-Height Bin ........................................................................... 18
REFRIGERATOR CARE ................................................................ 19
Cleaning ...................................................................................... 19
Changing the Light Bulbs ........................................................... 19
TROUBLESHOOTING ................................................................... 20
Operation .................................................................................... 20
Noise ........................................................................................... 21
Temperature and Moisture ......................................................... 22
Ice and Water ............................................................................. 23
Doors .......................................................................................... 25
WATER FILTER CERTIFICATIONS ............................................. 25
PERFORMANCE DATA SHEET ................................................... 26
WARRANTY ................................................................................... 27
SI_CURITI_ DU RI_FRIGI_RATEUR .............................................. 28
Mise au rebut adequate de votre vieux refrig6rateur ................ 29
INSTRUCTIONS D'INSTALLATION ............................................ 29
Deballage du r6frigerateur ......................................................... 29
Exigences d'emplacement ........................................................ 30
Retrait et reinstallation des portes du
refrig6rateur et de I'avant du tiroir ............................................. 30
Specifications electriques .......................................................... 34
Specifications de I'alimentation en eau ..................................... 34
Raccordement & I'alimentation en eau ...................................... 34
Installation de la poignee ........................................................... 36
Fermeture et alignement de la porte ......................................... 36
FILTRES ET ACCESSOIRES ....................................................... 37
Systeme de filtration de I'eau .................................................... 37
Installation du filtre a air ............................................................. 38
Installation du conservateur pour produits frais ........................ 38
Accessoires ................................................................................ 39
UTILISATION DU RI_FRIGI_RATEUR .......................................... 39
Ouverture et fermeture des portes ............................................ 39
Utilisation des commandes ....................................................... 40
Distributeur d'eau ....................................................................... 42
Machine a gla(2ons ..................................................................... 43
CARACTI_RISTIQUES DU RI_FRIGI_RATEUR ........................... 44
Tablettes du r6frigerateur ........................................................... 44
Garde-manger ............................................................................ 44
Bac a legumes ........................................................................... 45
CARACTI_RISTIQUES DE LA PORTE ......................................... 45
Balconnets a condiments .......................................................... 45
Balconnet frafcheur .................................................................... 45
Balconnet mi-hauteur ................................................................ 45
ENTRETIEN DU RI_FRIGI_RATEUR ............................................ 46
Nettoyage ................................................................................... 46
Remplacement des ampoules d'eclairage ................................ 46
DI_PANNAGE ................................................................................ 47
Fonctionnement ......................................................................... 47
Bruit ............................................................................................ 48
Temperature et humidite ............................................................ 49
Gla(2ons et eau ........................................................................... 50
Portes ......................................................................................... 52
FEUlLLE DE DONNI_ES SUR LA PERFORMANCE ................... 53
GARANTIE ..................................................................................... 54
W10405120A
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
[] Disconnect power before servicing.
Replace all parts and panels before operating.
Remove doors from your old refrigerator.
Use nonflammable cleaner.
Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
Use two or more people to move and install refrigerator.
Disconnect power before installing ice maker (on ice maker
kit ready models only).
Use a sturdy glass when dispensing ice (on some models).
Do not hit the refrigerator glass doors (on some models).
SAVE THESE INSTRUCTIONS
Proper Disposal of Your Old Refrigerator
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
Before You Throw Away Your Old Refrigerator or Freezer:
Takeoff the doors.
Leave the shelves in place so that children may not easily
climb inside.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for "just a few days." If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Important information to know about disposal of
refrigerants:
Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.
2
INSTALLATION INSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see "Refrigerator Safety."
Dispose of/recycle all packaging materials.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the refrigerator straight out when moving it. Do not wiggle or
"walk" the refrigerator when trying to move it, as floor
damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in "Refrigerator Care."
important information to know about glass shelves
and covets:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your refrigerator, allow for a V2"
(1.25 cm) of space on each side and at the top. Allow for a 1"
(2.54 cm) space behind the refrigerator. Ifyour refrigerator has an
ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave a 2" (5.08 cm) minimum space between the refrigerator and
wall to allow the door to swing open.
NOTE: This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature range
for optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F
(32°C). It is recommended that you do not install the refrigerator
near a heat source, such as an oven or radiator.
/
1/2" (1.25 cm)
2" (5.08 cm)
/
\
Dependingonthewidthofyourdooropening,itmaybe
necessarytoremovetherefrigeratordoorstomovethe
refrigeratorintoyourhome.
RemoveDoorsandHinges
IMPORTANT:
If the refrigerator was previously installed and you are moving
it out of the home, before you begin, turn the refrigerator
control OFF, and unplug the refrigerator or disconnect power.
Remove food and any adjustable door or utility bins from
doors.
Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet. Provide additional support for the
refrigerator door while the hinges are being removed. Do not
depend on the door gasket magnets to hold the door in place
while you are working.
All graphics referenced in the following instructions are
included later in this section after "Final Steps."
TOOLS NEEDED: 5/le", 3/8",and V4"hex head socket wrenches,
Torx®tT27 screwdriver, #2 Phillips screwdriver, and a flat-blade
screwdriver.
Replace Doors and Hinges
1. Replace the parts for the bottom hinge as shown in Bottom
Hinge graphic. Tighten screws. Replace the refrigerator door.
NOTE: Provide additional support for the refrigerator door
while the hinges are being moved. Do not depend on the door
gasket magnets to hold the door in place while you are
working.
2. Assemble the parts for the top hinges as shown in Top Hinge
graphic. Do not tighten the screws completely.
External Dispenser Models Only:
Reconnect the wiring plug on top of the left-hand side
refrigerator door.
Reconnect the water line by pulling back the locking
collar ring while firmly pushing the water line into the
connector. Check for leaks.
3. Align the door so that the bottom of the refrigerator door
aligns evenly with the top of the freezer drawer. Tighten all
screws.
4. Replace the top hinge covers.
Remove Doors and Hinges
1. Unplug refrigerator or disconnect power.
2. Remove the base grille. Grasp the grille firmly and pull it
toward you.
3. Starting with the right-hand side door, remove the parts for
the top hinge as shown in Top Hinge graphic. Lift the
refrigerator door from the bottom hinge pin.
4. Remove the hinge pin cover from the bottom hinge pin and
keep it for later use. See Bottom Hinge graphic.
5. Remove top hinge cover from the left-hand side refrigerator
door. Remove the parts for the top hinge as shown in Top
Hinge graphic.
External Dispenser Models Only:
Disconnect the wiring plug, located under the top left-
hand side door hinge, by wedging a flat-blade
screwdriver or your fingernail between the two sections.
See Wiring Plug graphic.
Disconnect the water line, located under the top left-hand
side door hinge, by pulling back on the locking collar
while pulling the water line out of the water line connector.
See Water Dispenser Tubing Connection graphic.
6. Lift the left-hand side door from the bottom hinge pin.
NOTE: On some models, remove the hinge pin cover from
the bottom hinge pin and keep it for later use. See Bottom
Hinge graphic.
Remove and Replace Freezer Drawer Front
IMPORTANT: Two people may be required to remove and
replace the freezer drawer. Graphics are included later in this
section.
Remove Drawer Front
1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer glides to the
drawer front. See Drawer Front Removal graphic.
NOTE: Loosen screws three to four turns. Keep the screws in
the drawer front.
3.
4.
Lift drawer front upward and off the screws. See Drawer Front
Removal graphic.
The refrigerator leveling/roller assembly protrudes from each
side of the cabinet base. Remove the three screws attaching
each assembly, and remove the assemblies. See Refrigerator
Leveling/Roller Assembly graphic.
t(t_>-lORX is a re,qistered trademark of Saturn Fasteners, Inc.
4
ReplaceDrawerFront
1. Aligntheleveling/rollerassemblywiththeholesoneachside
oftherefrigeratorcabinet.Usingthescrewsremoved,
reinstalltheassembliestothecabinetbase.Tightenthe
screwscompletely.
2. Slidethedrawerglidesoutofthefreezercompartment.Insert
thescrewsinthetopofthedrawerfrontintotheslotsinthe
drawerbrackets.SeeDrawerFrontReplacementgraphic.
3. Pullthedrawerbracketstowardyoutopositionthetwo
screwsinthebottomofthedrawerfrontintothebrackets.
Completelytightenthefourscrews.SeeDrawerFront
Replacementgraphic.
4. Replacethebasegrille.
Pullopenthefreezerdrawer.
Alignthethreeclipsonthebackofthebasegrillewiththe
threetabsatthebaseoftherefrigerator.
Pushthebasegrilleintowardtherefrigeratoruntilitis
firmlyinplace.
Final Steps
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A
B
1. Plug into a grounded 3 prong outlet.
2. Return all removable parts to doors and drawer and food to
refrigerator and freezer.
A.Tab
B.Clip
Style 1 - Non-Dispenser Models
Top Hinges
A. Hinge Cover Screw
B. Top Hinge Cover
C. 5/16" Hex-Head Hinge Screws
D. Top Hinge
Bottom Hinges
B
C
A. Hinge Pin Cover
B. Bottom Hinge
C. Hinge Screws
Leveling/Roller Assembly
A. Assembly Screws
A. Loosen 4 Door Bracket Screws
6
Style 2 - External Water Dispenser Models
Water Dispenser
Tubing Connection
\
\
\
\
\
\
\
\
A
A. Blue Outer Ring
Wiring Plug
Top Hinges
A. Hinge Cover Screw
B, Top Hinge Cover
C, _6" Hex-Head Hinge Screws
D. Top Hinge
Bottom Hinges
A
B
A. Hinge Pin Cover
B. Bottom Hinge
C. Hinge Screws
Leveling/Roller Assembly
A. Assembly Screws
¸
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection.
Recommended Grounding Method
A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn Cooling OFF,and then disconnect the
refrigerator from the electrical source. When you are finished,
reconnect the refrigerator to the electrical source and turn
Cooling ON. See "Using the Controls."
A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. Ifyou have questions about your water pressure, call a
licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill
after heavy usage. The tank capacity could be too low to
keep up with the requirements of the refrigerator.
If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See "Water
Filtration System."
If you have questions about your water pressure, call a licensed,
qualified plumber.
Read all directions before you begin.
IM PORTANT:
All installations must meet local plumbing code requirements.
Use copper tubing or Whirlpool supply line, Part Number
8212547RP, and check for leaks.
Install copper tubing only in areas where the temperatures
will remain above freezing.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Flat-blade screwdriver V4"Nut driver
7/le"and V_"Open-end or two V4"Drill bit
adjustable wrenches
Cordless drill
NOTE: Your refrigerator dealer has a kit available with a V4"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure asaddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3/le"
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
Connect to Water Line
Style 1
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a 1/2"to 1V4" (1.25 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
Make sure it is a cold water pipe.
Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure
both ends of copper tubing are cut square.
5. Using a cordless drill, drill a V4"hole in the cold water pipe
you have selected.
G,, B C
6=
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the V4"(6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten or you may crush the copper tubing.
8
7. Slip the compression sleeve and compression nut onto the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water is
clear. Turn OFF the shutoff valve on the water pipe. Coil the
copper tubing.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3. Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
6.
On models with ice makers, the ice maker is equipped with a
built-in water strainer. Ifyour water conditions require a
second water strainer, install it in the 1/4"(6.35 mm) water line
at either tube connection. Obtain a water strainer from your
nearest appliance dealer.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3. If the gray water tube supplied with the refrigerator is not long
enough, a 1/4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed
in order to connect the water tubing to an existing household
water line. Thread the provided nut onto the coupling on the
end of the copper tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
A
I/ II
B
4=
5.
A.Bulb
B.Nut (provided)
Turn shutoff valve ON.
Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Connect to Refrigerator
Style 1
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do
not overtighten.
3. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help avoid
damage to the tubing when the refrigerator is pushed back
against the wall.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
-- A
B
C
A B C D E F G
A. Refrigerator water tubing
B. Nut (provided)
C. Bulb
D. Coupling (provided)
E.Ferrule (purchased)
F Nut (purchased)
G. Household water fine
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Complete the Installation
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A. Tube clamp
B. Tube clamp screw
C. Copper tubing
D
E
D. Compression nut
E. Valve inlet
1. Plug into a grounded 3 prong outlet.
2. Flush the water system. See "Water Dispenser."
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to
completely fill ice container.
Parts Included: Handles (3)
Install Door Handles
1. Remove the handles from the packaging inside the
refrigerator.
NOTE: To avoid damaging the handles, place them on a
towel or other soft surface.
2.
Place the keyhole slots in the handle over the shoulder
screws (preinstalled on the door). Apply firm pressure on the
handle to slide it down onto the shoulder screws.
NOTE: Do not push the handle toward the door; this can
damage the door. Apply only downward pressure.
3. Repeat the previous steps to install the adjacent door handle.
Install Drawer Handle
1. Place the keyhole slots in the handle over the shoulder
screws (preinstalled on the drawer). Slide the handle firmly to
the right to fully engage the shoulder screws in the keyhole
slots.
NOTE: Do not push the handle toward the drawer; this can
damage the drawer.
2. Save all instructions.
Remove the Handles
Refrigerator Door
Lift the handle directly upward, and pull it off of the door.
If necessary, use a Phillips screwdriver to remove the
shoulder screws from the door.
Freezer Drawer
Slide the handle to the left to disengage the keyhole slot from
the shoulder screws, and pull it off of the drawer.
If necessary, use a Phillips screwdriver to remove the
shoulder screws from the drawer.
IMPORTANT: To comply with American Disabilities Act (ADA)
guidelines, fully retract the rollers into the cabinet to lower the
refrigerator.
Door Closing
The base grille covers the leveling screws and roller assemblies
located at the bottom of the refrigerator cabinet below the freezer
drawer. Before making adjustments, remove the base grille and
move the refrigerator to its final location.
1. Remove the base grille. Grasp the grille firmly and pull it
toward you.
2. Move the refrigerator to its final location.
NOTE: To allow the refrigerator to roll easier, raise the leveling
legs off the floor by turning the leveling screws
counterclockwise. The front rollers will be touching the floor.
3. So the doors will close easier, use a V4"hex driver to turn both
leveling screws clockwise. This will raise the front of the
refrigerator tilting it slightly downward to the rear. Turn both
leveling screws the same amount.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws. This
makes it easier to turn the screws.
A. Leveling screw
4. Open both doors again to make sure they close as easily as
you like and that they stay closed. If not, tilt the refrigerator
slightly more to the rear by turning both leveling screws to the
right. It may take several more turns.
NOTE: To keep the refrigerator level, you should turn both
leveling screws the same amount.
5. Replace the base grille.
Pull open the freezer drawer.
Align the three clips on the back of the base grille with the
three tabs at the base of the refrigerator.
10
Push the base grille in toward the refrigerator until it is
firmly in place. Changing the Water Filter
A
B
A.Tab
B.Clip
Door Alignment
If the space between the refrigerator doors and freezer drawer
looks uneven, you can adjust it using the following instructions:
1. Remove the top hinge cover.
2. Loosen the top hinge screws using a 5/16"socket or wrench.
3. Have someone hold the door in place or put a spacer
between the doors and drawer.
4. Tighten the top hinge screws once the door is in the desired
location.
5. Replace the top hinge cover.
FILTERS AND ACCESSORIES
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Water Filter Status Light
The water filter status light on the control panel will help you
know when to order and replace the water filter.
GOOD - The water filter icon on the control lights up in BLUE.
ORDER a replacement filter - The water filter icon on the
control lights up in YELLOW.
REPLACE the water filter - The water filter icon on the control
lights up in RED and "Replace Filter" will appear on the
display.
EXPIRED - The water filter icon lights up in RED and "Replace
Filter" flashes on the display.
NOTE: If water flow to your water dispenser or ice maker
decreases noticeably, change the filter sooner. The
disposable water filter should be replaced at least every
6 months, depending on your water quality and usage.
After changing the water filter, reset the status. Press and
hold the WATER FILTER button for 3 seconds. When the
system is reset, the water filter icon will return to its BLUE
color and the words "Replace Filter" will disappear from the
display.
1. Locate the water filter in the top-right corner of the
refrigerator compartment.
2. Lift open the filter cover door. The filter will be released and
then eject as the door is opened.
3. When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
4. Take the new filter out of its packaging and remove the
covers from the O-rings. Be sure the O-rings are still in place
after the covers are removed.
5. With the arrow pointing up, align the new filter with the filter
housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.
6. Close the filter cover door completely in order to snap the
filter into place. You may need to press hard.
7. Flush the water system. See "Water and Ice Dispensers."
The air filter reduces the buildup of odors. This helps to maintain
a cleaner environment inside the refrigerator.
On some models, your refrigerator's accessory packet includes
an air filter, which must be installed prior to use. On some
models, the air filter is already installed at the factory.
Installing the Air Filter
Install the air filter behind the vented door, located along the rear
interior wall of the refrigerator compartment.
1. Remove the air filter from its packaging.
NOTE: An air filter status indicator is included with the air
filter. The indicator is not needed for models that display the
air filter status on the control panel.
2. Lift open the vented door.
3. Snap the filter into place.
11
Air Filter Status Indicator
The control panel displays the Air Filter status.
GOOD - The air filter icon on the control lights up in BLUE.
ORDER a replacement - The air filter icon on the control lights
up in YELLOW.
REPLACE air filter - The air filter icon on the control lights up
in RED and "Replace Filter" will appear.
EXPIRED - The air filter icon lights up in RED and "Replace
Filter" flashes on the control display.
After replacing the air filter, press and hold the AIR FILTER button
for 3 seconds. The filter icons will turn off. See "Using the
Control(s)." When the system is reset, the air filter icon will return
to its BLUE color and the words "Replace Filter" will disappear
from the display.
NOTE: At any filter status, pressing and holding the AIR FILTER
button for 3 seconds will reset the air filter status to Good and the
air filter icon will turn off.
Replacing the Air Filter
The disposable air filter should be replaced every 6 months, or
when the status indicator air filter icon turns on and starts
flashing when the refrigerator door is opened.
To order a replacement air filter, contact us. See "Accessories."
1. Remove the used air filter by squeezing in on the side tabs.
2. Install the new air filter and reset the status indicator using
the instructions in the previous section.
The accessory packet includes two produce preserver pouches,
which should be installed in a crisper drawer prior to use.
NOTE: For best performance, always use two pouches.
The produce preserver absorbs ethylene, to slow the ripening
process of many produce items. As a result, certain produce
items will stay fresh longer.
Ethylene production and sensitivity varies depending on the type
of fruit or vegetable. To preserve freshness, it is best to separate
produce with sensitivity to ethylene from fruits that produce
moderate to high amounts of ethylene.
Produces Ethylene
Sensitivity
to Ethylene
High
Med.
Low
Very Low Med. High Very
Low High
Broccoli
Lettuce
Spinach
Asparagus
Citrus fruit
Carrots
Grapes
Canta-
loupe
Apples
Pears
Installing the Produce Preserver
CAUTION: IRRITANT
MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES
FORM WHEN MIXED WITH OTHER PRODUCTS.
Do not mix with cleaning products containing ammonia,
bleach or acids. Do not get in eyes, on skin or clothing. Do
not breathe dust. Keep out of reach of children.
FIRST AID TREATMENT: Contains potassium
permanganate. If swallowed, call a Poison Control Center or
doctor immediately. Do not induce vomiting. If in eyes, rinse
with water for 15 minutes. If on skin, rinse with water.
The produce preserver pouches should be installed in the
housing, located on the wall of one of the crisper drawers.
1. Remove the FreshFIow TM Produce Preserver pouches from
the packaging.
2. Lift up on the housing to remove it from the mounting tab.
3. Open the housing by pulling up and out on the back of the
top of the housing.
4. Place both pouches inside the housing, then snap the
housing back together.
5. Place the housing back on the mounting tab.
Installing the Status Indicator
The produce preserver comes with a status indicator, which
should be activated and installed at the same time the pouches
are installed.
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator until
the bubble pops, to activate the indicator.
3. Slide open the cap on the top of the produce preserver
housing.
4. Place the indicator in the top of the housing, facing outward.
12
5,
Slide the cap closed, and check that the indicator is visible
through the rectangular hole in the cap.
NOTE: The cap will not easily close if the indicator's bubble
has not been popped.
Replacing the Produce Preserver
The disposable pouches should be replaced every 6 months,
when the status indicator has completely changed from white to
red.
To order replacements, contact us. See "Accessories" for
information on ordering.
1. Remove the used pouches from the produce preserver
housing.
2. Remove the used status indicator.
3. Install the replacement pouches and status indicator using
the instructions in the previous sections.
The following accessories are available for your refrigerator. To
order, contact us and ask for the part numbers.
In the U.S.A., visit our web page www.maytag.com/accessories
or call 1-800-901-2042.
In Canada, visit our web page www.maytagparts.ca
or call 1-800-807-6777.
Stainless Steel Cleaner and Polish:
Order Part #4396095
Water Filter:
Order Part #W10295370A or FILTER1
Air Filter:
Order Part #W10311524 or AIR1
Ethylene Filter:
Order Part #W10346771A or FRESH1
Water Filter, Air Filter and Ethylene Filter Bundle Pack:
Order Part #W10443987BL
REFRIGERATOR USE
Wait 24 hours for your refrigerator to cool completely before
adding food. If you add food before the refrigerator has
cooled completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer temperature
controls to a colder than recommended setting will not cool
the compartments any faster.
The recommended setting should be correct for normal
household refrigerator use. The controls are set correctly
when milk or juice is as cold as you like and when ice cream
is firm.
If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
Control Panel
Depending on your model, your refrigerator has either an internal
control panel, located at the top of the refrigerator compartment,
or an external control panel, located above the external water
dispenser. Follow the instructions specific to your model.
Internal Control Panel
I_ c_er replace filter
o 1313 _li.
freezer temp air filter
cooling 131
off _ replace filter I_ coZder
_e 8= 13131313
6
speed cool moisture control water filter fridgetemp
External Control Panel
£ '=
There are two refrigerator compartment doors. The doors can be
opened and closed either separately or together.
There is a vertically-hinged seal on the left refrigerator door.
When the left side door is opened, the hinged seal
automatically folds inward so that it is out of the way.
When both doors are closed, the hinged seal automatically
forms a seal between the two doors.
IMPORTANT (External Control only): The display screen on the
dispenser control panel will turn off automatically and enter
"sleep" mode when the control buttons and dispenser levers
have not been used for 2 minutes or more. While in "sleep"
mode, the first press of a control button will only reactivate the
display screen, without changing any settings. After reactivation,
changes to any settings can then be made. If no changes are
made within 2 minutes, the display will re-enter "sleep" mode.
A. Hinged seal
13
Touch any control button on the dispenser panel to activate
the display screen.
Temperature Control
For your convenience, the temperature control is preset at the
factory. When you first install your refrigerator, make sure the
control is still set to the recommended setting as shown.
Internal Control - Recommended Setting "3 Boxes"
Cooling On/Off
Your refrigerator and freezer will not cool when cooling is
turned off. Follow the directions specific to your model.
Internal Control Panel
To turn cooling off, press and hold both the SPEEDCOOL and
MOISTURE CONTROL buttons at the same time for
3 seconds. When cooling is off, "Cooling Off" will appear on
the display screen.
To turn cooling back on. Press and hold both the
SPEEDCOOL and MOISTURE CONTROL buttons at the same
time for 3 seconds. When cooling is on, "Cooling Off" will
disappear and the previously selected settings will appear on
the display screen.
External Control - Recommended Setting "3 Snowflakes"
External Control Panel
To turn cooling off, press and hold both the FREEZER TEMP
and FRIDGE TEMP buttons at the same time for 3 seconds.
When cooling is off, "Cooling Off" will appear on the display
screen.
To turn cooling back on. Press and hold both the FREEZER
TEMP and FRIDGE TEMP buttons at the same time for
3 seconds. When cooling is on, "Cooling Off" will disappear
and the previously selected settings will appear on the display
screen.
Adjusting the Controls
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the following chart
as a guide.
Press the TEMP button to display the desired number of
snowflakes or boxes from (1 snowflake/box [least cold] to all
5 snowflakes/boxes [coldest]).
NOTE: Except when starting the refrigerator, do not adjust the
control more than one setting at a time. Wait 24 hours between
adjustments for the temperature to stabilize.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm FRIDGE TEMP one
more snowflake/box
FREEZER too warm/too little ice FREEZER TEMP one
more snowflake/box
REFRIGERATOR too cold FRIDGE TEMP one less
snowflake/box
FREEZER too cold FREEZER one less
snowflake/box
14
Additional Features
Door Open Alarm
The Door Open icon lights upwhenever either door is
opened.
O
Internal Control External Control
When either door is open for 5 minutes and cooling is on, an
alert tone will sound three times, and the Door Open icon will
flash seven times. This pattern will repeat every 2 minutes
until all the doors are closed properly. The feature then resets
and will reactivate when either door is left open again for
5 minutes.
NOTES:
To mute the audible alarm while keeping the doors open,
such as while cleaning the inside of the refrigerator, press any
button on the control panel. The alarm sound will be
temporarily turned off, but the Door Open icon will still be
displayed on the dispenser control panel.
Both doors must be fully closed to turn off the Door Open
icon.
SpeedCool
The SpeedCool feature assists during times of high refrigerator
use, full grocery loads or temporarily warm room temperatures.
Press SPEEDCOOL to set the freezer and refrigerator to the
coldest temperature settings. Press SPEEDCOOL again to
return to the selected temperature set point.
NOTES:
The SpeedCool icon will be illuminated while the
refrigerator is in SpeedCool mode.
The SpeedCool feature will turn off automatically after
24 hours.
_e E
Internal Control External Control
Moisture Control
The moisture control feature turns on a heater to help reduce
moisture on the door hinge seal. Use in humid environments or
when you notice moisture on the door hinge seal. The refrigerator
uses more energy when Moisture Control is on.
NOTE: The moisture control icon will light up to indicate the
feature is on.
To turn on/off the moisture control feature:
Internal Control Panel - Press and hold MOISTURE
CONTROL for 3 seconds.
External Control Panel - Press and hold LIGHT for 3 seconds.
Internal Control External Control
Water Filter Status Light and Reset
The filter reset control allows you to restart the water filter status
tracking feature each time you replace the water filter. See "Water
Filtration System."
Press and hold WATER FILTER for 3 seconds, to reset the
water filter status to Good. The water filter icon will turn blue.
6
Internal Control External Control
Air Filter Status Light and Reset
The filter reset control allows you to restart the air filter status
tracking feature each time you replace the air filter. See "Install Air
Filter."
Press and hold AIR FILTER for 3 seconds, to reset the air filter
status to Good. The air filter icon will turn blue.
Internal Control External Control
IM PORTANT:
Allow 3 hours for the refrigerator to cool down and chill water.
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The dispensing system will not operate when the refrigerator
door is open.
Flush the Water System
Air in the water dispensing system can cause the water dispenser
to drip. After connecting the refrigerator to a water source or
replacing the water filter, flush the water system.
Flushing the water dispensing system, forces air from the water
line and filter and prepares the water filter for use. Additional
flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of
the dispenser.
1. Using a sturdy container, depress and hold the water
dispenser paddle for 5 seconds.
2. Release the dispenser paddle for 5 seconds. Repeat steps 1
and 2 until water begins to flow.
3. Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total
of 4 gal. (15 L) has been dispensed.
Dispense Water
IM PORTANT:
The dispensing system will not operate when the refrigerator
door is open.
The display screen on the dispenser control panel will turn off
automatically and enter "sleep" mode when the control
buttons and dispenser levers have not been used for
2 minutes or more. While in "sleep" mode, the first press of a
control button will only reactivate the display screen, without
changing any settings. After reactivation, changes to any
settings can then be made. If no changes are made within
2 minutes, the display will re-enter "sleep" mode.
To dispense water:
1. Press a sturdy glass against the water dispenser paddle.
2. Remove the glass to stop dispensing.
15
Dispenser Light
When you use the dispenser, the light will automatically turn on.
If you want the light to be on continuously, you may turn on the
light. The light icon will illuminate when the light is on.
ON: Press LIGHT quickly to turn on the dispenser light.
OFF: Press LIGHT quickly to turn off the dispenser light.
NOTES:
If you unintentionally press and hold the LIGHT button for
3 seconds or longer, you will turn on the Moisture control
feature. If this happens, press and hold LIGHT for 3 seconds
again to turn off the Moisture control feature.
The dispenser lights are LEDs that cannot be changed. If it
appears that your dispenser lights are not working, see
"Troubleshooting" for more information.
Dispenser Lock
The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the
refrigerator, to the ice maker, or to the dispenser light. It simply
deactivates the controls and dispenser levers. To turn off the ice
maker, see "Ice Maker and Storage Bin."
Press and hold SPEEDCOOL for 3 seconds to lock the
dispenser.
Press and hold SPEEDCOOL for 3 seconds again to unlock
the dispenser.
The lock icon will illuminate when the dispenser is locked.
IMPORTANT: For models with a water filter, after connecting the
refrigerator to a water source or replacing the water filter, fill and
discard three full containers of ice to prepare the water filter for
use.
Turning the Ice Maker On/Off
To turn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,
the ice cubes will fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff arm up or down.
Ice Storage Bin
1. Wash the ice storage bin with mild soap and warm water.
2. Slide the ice storage bin under the ice maker, and push it
toward the back as far as it will go.
3. Lower the arm on the ice maker to the "on" position.
NOTE: It usually takes approximately 24 hours for the ice
maker to begin producing ice. You may notice the ice has an
"off-taste." If so, discard the first three batches of ice
produced. After that the "off-taste" should be gone.
Ice Production Rate
The ice maker should produce approximately 8 to 12 batches
of ice in a 24-hour period. Allow 3 days to completely fill the
ice container.
To increase ice production, lower the freezer and refrigerator
temperature. See "Using the Control(s)." Wait 24 hours
between adjustments.
Remember
The quality of your ice will be only as good as the quality of
the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker
and lead to poor quality ice. If a softened water supply cannot
be avoided, make sure the water softener is operating
properly and is well maintained.
Do not use anything sharp to break up the ice in the bin. This
can cause damage to the ice storage bin and the dispenser
mechanism.
Do not store anything on top of or in the ice maker or ice
storage bin.
REFRIGERATOR FEATURES
NOTE: Your model may have some or all of these features.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
i÷%,
The shelves in your refrigerator are adjustable to match your
individual storage needs.
Glass Shelves
To remove a shelf:
1. Remove items from the shelf.
2. Slide the shelf straight out to the stop.
3. Depending on your model, lift the back or front of the shelf
past the stop. Pull the shelf out the rest of the way.
16
To replace a shelf:
1. Slide the back of the shelf into the track in the wall of the
cabinet.
2. Guide the front of the shelf into the shelf track. Be sure to
slide the shelf in all the way.
Fold Away Shelf (on some models)
To retract the fold away shelf:
Retract the fold away section of the shelf by holding the front
of the shelf with one hand and lifting up on the center front of
the shelf. Then push back and down on the shelf until it slides
beneath the back section of the shelf.
To replace the fold away shelf:
Replace the fold away section of the shelf by holding the front
of the shelf with one hand and pulling the center of the shelf
until the fold away section is returned to its full shelf position.
Pantry Drawer Control
The amount of air flowing through the pantry drawer affects the
temperature inside the drawer.
The airflow control is located on the left side of the pantry drawer.
To adjust the airflow:
Colder - Slide the control forward, toward the front of the
pantry drawer, the airflow is open.
Cold - Slide the control all the way toward the rear of the
pantry drawer. The airflow is closed, as shown.
Pantry Drawer
To remove and replace the pantry drawer:
1. Slide pantry drawer out to the stop.
2. Lift front of pantry drawer with one hand while supporting
bottom of drawer with other hand. Slide drawer out the rest of
the way.
3. Replace the drawer by sliding it back in fully past the drawer
stop.
Pantry Drawer Cover
To remove and replace the pantry drawer cover:
1. Remove the pantry drawer.
2. From underneath, push up on the glass cover and pull it out.
3. Replace the pantry drawer cover by lowering it into place.
4. Replace the pantry drawer.
Crisper Drawers
To remove and replace the crisper drawer:
1. Slide the crisper drawer straight out to the stop. Lift the front
and slide the drawer out the rest of the way.
2. Replace the drawer by sliding the drawer in fully past the
stop.
Crisper Cover
To remove and replace the glass crisper cover:
1. Pull the glass straight out.
2. Replace the glass by pushing it straight in.
17
Crisper Humidity Control (on some models)
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and
HIGH.
LOW (open) lets moist air out of the crisper for best storage of
fruits and vegetables with skins.
Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store
in a loosely closed paper bag on a refrigerator shelf.
Vegetables with skins: Place in plastic bag or plastic
container and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of
fresh, leafy vegetables.
Leafy vegetables: Wash in cold water, drain and trim or tear
off bruised and discolored areas. Place in plastic bag or
plastic container and store in crisper.
DOOR FEATURES
NOTE: Your model may have some or all of these features.
To remove and replace the condiment bins:
1. Tilt the bin by grabbing it and pulling outward.
2. Remove the bin by grabbing it and lifting it upward off the
glides.
3. Replace the bin by sliding it back onto the glides and then
push it closed.
BiR
To remove and replace the fresh bin:
1. Open the bin by grabbing the top center lip of the bin and
tilting the bin outward.
2.
3.
Remove the bin by grabbing both sides of the bin and lifting
the bin upward off the glides.
Replace the bin by sliding it back into its tilted position on the
glides and then push it closed.
To remove and replace the half-height bin:
1. Tilt the bin by grabbing it and pulling outward.
2. Remove the bin by grabbing it and lifting it upward off the
glides.
3. Replace the bin by sliding it back onto the glides and then
push it closed.
18
REFRIGERATOR CARE
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid
buildup of odors. Wipe up spills immediately.
IMPORTANT:
Because air circulates between both sections, any odors
formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid
odor transfer and drying out of food, wrap or cover foods
tightly.
For stainless steel models, stainless steel is corrosion-
resistant and not corrosion-proof. To help avoid corrosion of
your stainless steel, keep your surfaces clean by using the
following cleaning instructions.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, muriatic acid,
cleaning waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on exterior surfaces (doors and
cabinet), plastic parts, interior and door liners or gaskets. Do not
use paper towels, scouring pads, or other harsh cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
3. Clean the exterior surfaces.
Painted metal: Wash painted metal exteriors with a clean,
soft cloth or sponge and a mild detergent in warm water.
Rinse surfaces with clean, warm water and dry immediately
to avoid water spots.
Stainless steel: Wash stainless steel surfaces with a clean,
soft cloth or sponge and a mild detergent in warm water.
Rinse surfaces with clean, warm water and dry immediately
to avoid water spots.
NOTE: When cleaning stainless steel, always wipe in the
direction of the grain to avoid cross-grain scratching.
4.
5.
There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
Remove the base grille.
Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
Replace the base grille when finished.
Plug in refrigerator or reconnect power.
IM PC RTANT:
Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with an appliance bulb of the same size,
shape, and wattage.
To ensure optimum refrigerator performance, replace light
bulbs as soon as they burn out.
Refrigerator Compartment Light
The lighting located at the top of the refrigerator compartment
never needs to be replaced. If the lights do not illuminate when
the door is opened call for assistance or service. In the U.S.A, call
1-800-253-1301. In Canada, call 1-800-807-6777.
1.
2.
Freezer Compartment Light (on some models)
Unplug the refrigerator or disconnect power.
Remove the light shield (on some models).
Top of the freezer compartment - Slide the light shield
toward the back of the compartment to release it from the
light assembly.
3. Replace the burned-out bulb with an appliance bulb(s) no
greater than 25 watts.
4. Replace the light shield.
5. Plug in refrigerator or reconnect power.
19
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call.
In the U.S.A., www.maytag.com In Canada, www.maytag.ca
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
The refrigerator will not
operate
Check electrical supply Plug the power cord into a grounded 3 prong outlet.
Do not use an extension cord.
Make sure there is power to the outlet. Plug in a lamp to see
if the outlet is working.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Check controls Make sure the controls are turned on. See "Using the
Controls."
New installation Allow 24 hours following installation for the refrigerator to
cool completely.
NOTE: Adjusting the temperature controls to the coldest
setting will not cool either compartment quicker.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Maytag MFF2055YEB00 User Instructions

Catégorie
Frigos
Taper
User Instructions
Ce manuel convient également à

dans d''autres langues