Maytag MFF2055YEW00 User Instructions

Marque: Maytag

Modèle: MFF2055YEW00

Catégorie: Frigos

Taper: User Instructions

Ce manuel convient également à

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.maytag.com for additional information. If you still need assistance, call us at 1-800-688-9900.

In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de

su producto, visite: www.maytag.com.

Necesitara su nQmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

Table of Contents / Table des mati res

REFRIGERATOR SAFETY .............................................................. 2

Proper Disposal of Your Old Refrigerator .................................... 2

INSTALLATION INSTRUCTIONS ................................................... 3

Unpack the Refrigerator ............................................................... 3

Location Requirements ................................................................ 3

Remove and Replace Refrigerator Doors and Drawer Front ....... 4

Electrical Requirements ................................................................ 8

Water Supply Requirements ........................................................ 8

Connect the Water Supply ........................................................... 8

Handle Installation ...................................................................... 10

Door Closing and Door Alignment ............................................. 10

FILTERS AND ACCESSORIES ..................................................... 11

Water Filtration System .............................................................. 11

Install Air Filter ............................................................................ 11

Install Produce Preserver ........................................................... 12

Accessories ................................................................................ 13

REFRIGERATOR USE ................................................................... 13

Opening and Closing Doors ....................................................... 13

Using the Controls ...................................................................... 13

Water Dispenser ......................................................................... 15

Ice Maker .................................................................................... 16

REFRIGERATOR FEATURES ....................................................... 16

Refrigerator Shelves ................................................................... 16

Pantry Drawer ............................................................................. 17

Crisper ........................................................................................ 17

DOOR FEATURES ......................................................................... 18

Condiment Bins .......................................................................... 18

Fresh Bin ..................................................................................... 18

Half-Height Bin ........................................................................... 18

REFRIGERATOR CARE ................................................................ 19

Cleaning ...................................................................................... 19

Changing the Light Bulbs ........................................................... 19

TROUBLESHOOTING ................................................................... 20

Operation .................................................................................... 20

Noise ........................................................................................... 21

Temperature and Moisture ......................................................... 22

Ice and Water ............................................................................. 23

Doors .......................................................................................... 25

WATER FILTER CERTIFICATIONS ............................................. 25

PERFORMANCE DATA SHEET ................................................... 26

WARRANTY ................................................................................... 27

SI_CURITI_ DU RI_FRIGI_RATEUR .............................................. 28

Mise au rebut adequate de votre vieux refrig6rateur ................ 29

INSTRUCTIONS D'INSTALLATION ............................................ 29

Deballage du r6frigerateur ......................................................... 29

Exigences d'emplacement ........................................................ 30

Retrait et reinstallation des portes du

refrig6rateur et de I'avant du tiroir ............................................. 30

Specifications electriques .......................................................... 34

Specifications de I'alimentation en eau ..................................... 34

Raccordement & I'alimentation en eau ...................................... 34

Installation de la poignee ........................................................... 36

Fermeture et alignement de la porte ......................................... 36

FILTRES ET ACCESSOIRES ....................................................... 37

Systeme de filtration de I'eau .................................................... 37

Installation du filtre a air ............................................................. 38

Installation du conservateur pour produits frais ........................ 38

Accessoires ................................................................................ 39

UTILISATION DU RI_FRIGI_RATEUR .......................................... 39

Ouverture et fermeture des portes ............................................ 39

Utilisation des commandes ....................................................... 40

Distributeur d'eau ....................................................................... 42

Machine a gla(2ons ..................................................................... 43

CARACTI_RISTIQUES DU RI_FRIGI_RATEUR ........................... 44

Tablettes du r6frigerateur ........................................................... 44

Garde-manger ............................................................................ 44

Bac a legumes ........................................................................... 45

CARACTI_RISTIQUES DE LA PORTE ......................................... 45

Balconnets a condiments .......................................................... 45

Balconnet frafcheur .................................................................... 45

Balconnet mi-hauteur ................................................................ 45

ENTRETIEN DU RI_FRIGI_RATEUR ............................................ 46

Nettoyage ................................................................................... 46

Remplacement des ampoules d'eclairage ................................ 46

DI_PANNAGE ................................................................................ 47

Fonctionnement ......................................................................... 47

Bruit ............................................................................................ 48

Temperature et humidite ............................................................ 49

Gla(2ons et eau ........................................................................... 50

Portes ......................................................................................... 52

FEUlLLE DE DONNI_ES SUR LA PERFORMANCE ................... 53

GARANTIE ..................................................................................... 54

W10405120A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

[] Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily

climb inside.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in "Refrigerator Care."

important information to know about glass shelves

and covets:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a V2"

(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. Ifyour refrigerator has an

ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space between the refrigerator and

wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range

for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

1/2" (1.25 cm)

2" (5.08 cm)

Dependingonthewidthofyourdooropening,itmaybe

necessarytoremovetherefrigeratordoorstomovethe

refrigeratorintoyourhome.

RemoveDoorsandHinges

IMPORTANT:

• If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control OFF, and unplug the refrigerator or disconnect power.

Remove food and any adjustable door or utility bins from

doors.

• Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet. Provide additional support for the

refrigerator door while the hinges are being removed. Do not

depend on the door gasket magnets to hold the door in place

while you are working.

• All graphics referenced in the following instructions are

included later in this section after "Final Steps."

TOOLS NEEDED: 5/le", 3/8",and V4"hex head socket wrenches,

Torx®tT27 screwdriver, #2 Phillips screwdriver, and a flat-blade

screwdriver.

Replace Doors and Hinges

1. Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

2. Assemble the parts for the top hinges as shown in Top Hinge

graphic. Do not tighten the screws completely.

External Dispenser Models Only:

• Reconnect the wiring plug on top of the left-hand side

refrigerator door.

• Reconnect the water line by pulling back the locking

collar ring while firmly pushing the water line into the

connector. Check for leaks.

3. Align the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Replace the top hinge covers.

Remove Doors and Hinges

1. Unplug refrigerator or disconnect power.

2. Remove the base grille. Grasp the grille firmly and pull it

toward you.

3. Starting with the right-hand side door, remove the parts for

the top hinge as shown in Top Hinge graphic. Lift the

refrigerator door from the bottom hinge pin.

4. Remove the hinge pin cover from the bottom hinge pin and

keep it for later use. See Bottom Hinge graphic.

5. Remove top hinge cover from the left-hand side refrigerator

door. Remove the parts for the top hinge as shown in Top

Hinge graphic.

External Dispenser Models Only:

• Disconnect the wiring plug, located under the top left-

hand side door hinge, by wedging a flat-blade

screwdriver or your fingernail between the two sections.

See Wiring Plug graphic.

• Disconnect the water line, located under the top left-hand

side door hinge, by pulling back on the locking collar

while pulling the water line out of the water line connector.

See Water Dispenser Tubing Connection graphic.

6. Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the hinge pin cover from

the bottom hinge pin and keep it for later use. See Bottom

Hinge graphic.

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and

replace the freezer drawer. Graphics are included later in this

section.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

The refrigerator leveling/roller assembly protrudes from each

side of the cabinet base. Remove the three screws attaching

each assembly, and remove the assemblies. See Refrigerator

Leveling/Roller Assembly graphic.

t(t_>-lORX is a re,qistered trademark of Saturn Fasteners, Inc.

ReplaceDrawerFront

1. Aligntheleveling/rollerassemblywiththeholesoneachside

oftherefrigeratorcabinet.Usingthescrewsremoved,

reinstalltheassembliestothecabinetbase.Tightenthe

screwscompletely.

2. Slidethedrawerglidesoutofthefreezercompartment.Insert

thescrewsinthetopofthedrawerfrontintotheslotsinthe

drawerbrackets.SeeDrawerFrontReplacementgraphic.

3. Pullthedrawerbracketstowardyoutopositionthetwo

screwsinthebottomofthedrawerfrontintothebrackets.

Completelytightenthefourscrews.SeeDrawerFront

Replacementgraphic.

4. Replacethebasegrille.

• Pullopenthefreezerdrawer.

• Alignthethreeclipsonthebackofthebasegrillewiththe

threetabsatthebaseoftherefrigerator.

• Pushthebasegrilleintowardtherefrigeratoruntilitis

firmlyinplace.

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Return all removable parts to doors and drawer and food to

refrigerator and freezer.

A.Tab

B.Clip

Style 1 - Non-Dispenser Models

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

C. 5/16" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Leveling/Roller Assembly

A. Assembly Screws

A. Loosen 4 Door Bracket Screws

Style 2 - External Water Dispenser Models

Water Dispenser

Tubing Connection

A. Blue Outer Ring

Wiring Plug

Top Hinges

A. Hinge Cover Screw

B, Top Hinge Cover

C, _6" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Leveling/Roller Assembly

A. Assembly Screws

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF,and then disconnect the

refrigerator from the electrical source. When you are finished,

reconnect the refrigerator to the electrical source and turn

Cooling ON. See "Using the Controls."

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. Ifyou have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage. The tank capacity could be too low to

keep up with the requirements of the refrigerator.

• If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water

Filtration System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IM PORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

• Install copper tubing only in areas where the temperatures

will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Flat-blade screwdriver • V4"Nut driver

• 7/le"and V_"Open-end or two • V4"Drill bit

adjustable wrenches

• Cordless drill

NOTE: Your refrigerator dealer has a kit available with a V4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure asaddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/le"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Connect to Water Line

Style 1

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"to 1V4" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a cordless drill, drill a V4"hole in the cold water pipe

you have selected.

G,, B C

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the V4"(6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal.

Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut onto the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

On models with ice makers, the ice maker is equipped with a

built-in water strainer. Ifyour water conditions require a

second water strainer, install it in the 1/4"(6.35 mm) water line

at either tube connection. Obtain a water strainer from your

nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a 1/4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed

in order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

I/ II

A.Bulb

B.Nut (provided)

Turn shutoff valve ON.

Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

-- A

A B C D E F G

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (provided)

E.Ferrule (purchased)

F Nut (purchased)

G. Household water fine

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water Dispenser."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

Parts Included: Handles (3)

Install Door Handles

1. Remove the handles from the packaging inside the

refrigerator.

NOTE: To avoid damaging the handles, place them on a

towel or other soft surface.

Place the keyhole slots in the handle over the shoulder

screws (preinstalled on the door). Apply firm pressure on the

handle to slide it down onto the shoulder screws.

NOTE: Do not push the handle toward the door; this can

damage the door. Apply only downward pressure.

3. Repeat the previous steps to install the adjacent door handle.

Install Drawer Handle

1. Place the keyhole slots in the handle over the shoulder

screws (preinstalled on the drawer). Slide the handle firmly to

the right to fully engage the shoulder screws in the keyhole

slots.

NOTE: Do not push the handle toward the drawer; this can

damage the drawer.

2. Save all instructions.

Remove the Handles

Refrigerator Door

• Lift the handle directly upward, and pull it off of the door.

• If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

Freezer Drawer

• Slide the handle to the left to disengage the keyhole slot from

the shoulder screws, and pull it off of the drawer.

• If necessary, use a Phillips screwdriver to remove the

shoulder screws from the drawer.

IMPORTANT: To comply with American Disabilities Act (ADA)

guidelines, fully retract the rollers into the cabinet to lower the

refrigerator.

Door Closing

The base grille covers the leveling screws and roller assemblies

located at the bottom of the refrigerator cabinet below the freezer

drawer. Before making adjustments, remove the base grille and

move the refrigerator to its final location.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Move the refrigerator to its final location.

NOTE: To allow the refrigerator to roll easier, raise the leveling

legs off the floor by turning the leveling screws

counterclockwise. The front rollers will be touching the floor.

3. So the doors will close easier, use a V4"hex driver to turn both

leveling screws clockwise. This will raise the front of the

refrigerator tilting it slightly downward to the rear. Turn both

leveling screws the same amount.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws.

A. Leveling screw

4. Open both doors again to make sure they close as easily as

you like and that they stay closed. If not, tilt the refrigerator

slightly more to the rear by turning both leveling screws to the

right. It may take several more turns.

NOTE: To keep the refrigerator level, you should turn both

leveling screws the same amount.

5. Replace the base grille.

• Pull open the freezer drawer.

• Align the three clips on the back of the base grille with the

three tabs at the base of the refrigerator.

• Push the base grille in toward the refrigerator until it is

firmly in place. Changing the Water Filter

A.Tab

B.Clip

Door Alignment

If the space between the refrigerator doors and freezer drawer

looks uneven, you can adjust it using the following instructions:

1. Remove the top hinge cover.

2. Loosen the top hinge screws using a 5/16"socket or wrench.

3. Have someone hold the door in place or put a spacer

between the doors and drawer.

4. Tighten the top hinge screws once the door is in the desired

location.

5. Replace the top hinge cover.

FILTERS AND ACCESSORIES

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Light

The water filter status light on the control panel will help you

know when to order and replace the water filter.

• GOOD - The water filter icon on the control lights up in BLUE.

• ORDER a replacement filter - The water filter icon on the

control lights up in YELLOW.

• REPLACE the water filter - The water filter icon on the control

lights up in RED and "Replace Filter" will appear on the

display.

• EXPIRED - The water filter icon lights up in RED and "Replace

Filter" flashes on the display.

NOTE: If water flow to your water dispenser or ice maker

decreases noticeably, change the filter sooner. The

disposable water filter should be replaced at least every

6 months, depending on your water quality and usage.

• After changing the water filter, reset the status. Press and

hold the WATER FILTER button for 3 seconds. When the

system is reset, the water filter icon will return to its BLUE

color and the words "Replace Filter" will disappear from the

display.

1. Locate the water filter in the top-right corner of the

refrigerator compartment.

2. Lift open the filter cover door. The filter will be released and

then eject as the door is opened.

3. When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

4. Take the new filter out of its packaging and remove the

covers from the O-rings. Be sure the O-rings are still in place

after the covers are removed.

5. With the arrow pointing up, align the new filter with the filter

housing and slide it into place. The filter cover door will

automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the

filter into place. You may need to press hard.

7. Flush the water system. See "Water and Ice Dispensers."

The air filter reduces the buildup of odors. This helps to maintain

a cleaner environment inside the refrigerator.

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use. On some

models, the air filter is already installed at the factory.

Installing the Air Filter

Install the air filter behind the vented door, located along the rear

interior wall of the refrigerator compartment.

1. Remove the air filter from its packaging.

NOTE: An air filter status indicator is included with the air

filter. The indicator is not needed for models that display the

air filter status on the control panel.

2. Lift open the vented door.

3. Snap the filter into place.

Air Filter Status Indicator

The control panel displays the Air Filter status.

• GOOD - The air filter icon on the control lights up in BLUE.

• ORDER a replacement - The air filter icon on the control lights

up in YELLOW.

• REPLACE air filter - The air filter icon on the control lights up

in RED and "Replace Filter" will appear.

• EXPIRED - The air filter icon lights up in RED and "Replace

Filter" flashes on the control display.

After replacing the air filter, press and hold the AIR FILTER button

for 3 seconds. The filter icons will turn off. See "Using the

Control(s)." When the system is reset, the air filter icon will return

to its BLUE color and the words "Replace Filter" will disappear

from the display.

NOTE: At any filter status, pressing and holding the AIR FILTER

button for 3 seconds will reset the air filter status to Good and the

air filter icon will turn off.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, or

when the status indicator air filter icon turns on and starts

flashing when the refrigerator door is opened.

To order a replacement air filter, contact us. See "Accessories."

1. Remove the used air filter by squeezing in on the side tabs.

2. Install the new air filter and reset the status indicator using

the instructions in the previous section.

The accessory packet includes two produce preserver pouches,

which should be installed in a crisper drawer prior to use.

NOTE: For best performance, always use two pouches.

The produce preserver absorbs ethylene, to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

Produces Ethylene

Sensitivity

to Ethylene

High

Med.

Low

Very Low Med. High Very

Low High

Broccoli

Lettuce

Spinach

Asparagus

Citrus fruit

Carrots

Grapes

Canta-

loupe

Apples

Pears

Installing the Produce Preserver

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

The produce preserver pouches should be installed in the

housing, located on the wall of one of the crisper drawers.

1. Remove the FreshFIow TM Produce Preserver pouches from

the packaging.

2. Lift up on the housing to remove it from the mounting tab.

3. Open the housing by pulling up and out on the back of the

top of the housing.

4. Place both pouches inside the housing, then snap the

housing back together.

5. Place the housing back on the mounting tab.

Installing the Status Indicator

The produce preserver comes with a status indicator, which

should be activated and installed at the same time the pouches

are installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator until

the bubble pops, to activate the indicator.

3. Slide open the cap on the top of the produce preserver

housing.

4. Place the indicator in the top of the housing, facing outward.

Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's bubble

has not been popped.

Replacing the Produce Preserver

The disposable pouches should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order replacements, contact us. See "Accessories" for

information on ordering.

1. Remove the used pouches from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement pouches and status indicator using

the instructions in the previous sections.

The following accessories are available for your refrigerator. To

order, contact us and ask for the part numbers.

In the U.S.A., visit our web page www.maytag.com/accessories

or call 1-800-901-2042.

In Canada, visit our web page www.maytagparts.ca

or call 1-800-807-6777.

Stainless Steel Cleaner and Polish:

Order Part #4396095

Water Filter:

Order Part #W10295370A or FILTER1

Air Filter:

Order Part #W10311524 or AIR1

Ethylene Filter:

Order Part #W10346771A or FRESH1

Water Filter, Air Filter and Ethylene Filter Bundle Pack:

Order Part #W10443987BL

REFRIGERATOR USE

Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has

cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

The recommended setting should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream

is firm.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Control Panel

Depending on your model, your refrigerator has either an internal

control panel, located at the top of the refrigerator compartment,

or an external control panel, located above the external water

dispenser. Follow the instructions specific to your model.

Internal Control Panel

I_ c_er replace filter

o 1313 _li.

• freezer temp air filter

cooling 131

off _ replace filter I_ coZder

_e 8= 13131313

speed cool moisture control water filter fridgetemp

External Control Panel

• £ '=

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

IMPORTANT (External Control only): The display screen on the

dispenser control panel will turn off automatically and enter

"sleep" mode when the control buttons and dispenser levers

have not been used for 2 minutes or more. While in "sleep"

mode, the first press of a control button will only reactivate the

display screen, without changing any settings. After reactivation,

changes to any settings can then be made. If no changes are

made within 2 minutes, the display will re-enter "sleep" mode.

A. Hinged seal

• Touch any control button on the dispenser panel to activate

the display screen.

Temperature Control

For your convenience, the temperature control is preset at the

factory. When you first install your refrigerator, make sure the

control is still set to the recommended setting as shown.

Internal Control - Recommended Setting "3 Boxes"

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is

turned off. Follow the directions specific to your model.

Internal Control Panel

• To turn cooling off, press and hold both the SPEEDCOOL and

MOISTURE CONTROL buttons at the same time for

3 seconds. When cooling is off, "Cooling Off" will appear on

the display screen.

• To turn cooling back on. Press and hold both the

SPEEDCOOL and MOISTURE CONTROL buttons at the same

time for 3 seconds. When cooling is on, "Cooling Off" will

disappear and the previously selected settings will appear on

the display screen.

External Control - Recommended Setting "3 Snowflakes"

External Control Panel

• To turn cooling off, press and hold both the FREEZER TEMP

and FRIDGE TEMP buttons at the same time for 3 seconds.

When cooling is off, "Cooling Off" will appear on the display

screen.

To turn cooling back on. Press and hold both the FREEZER

TEMP and FRIDGE TEMP buttons at the same time for

3 seconds. When cooling is on, "Cooling Off" will disappear

and the previously selected settings will appear on the display

screen.

Adjusting the Controls

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the following chart

as a guide.

• Press the TEMP button to display the desired number of

snowflakes or boxes from (1 snowflake/box [least cold] to all

5 snowflakes/boxes [coldest]).

NOTE: Except when starting the refrigerator, do not adjust the

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm FRIDGE TEMP one

more snowflake/box

FREEZER too warm/too little ice FREEZER TEMP one

more snowflake/box

REFRIGERATOR too cold FRIDGE TEMP one less

snowflake/box

FREEZER too cold FREEZER one less

snowflake/box

Additional Features

Door Open Alarm

• The Door Open icon lights upwhenever either door is

opened.

Internal Control External Control

When either door is open for 5 minutes and cooling is on, an

alert tone will sound three times, and the Door Open icon will

flash seven times. This pattern will repeat every 2 minutes

until all the doors are closed properly. The feature then resets

and will reactivate when either door is left open again for

5 minutes.

NOTES:

• To mute the audible alarm while keeping the doors open,

such as while cleaning the inside of the refrigerator, press any

button on the control panel. The alarm sound will be

temporarily turned off, but the Door Open icon will still be

displayed on the dispenser control panel.

• Both doors must be fully closed to turn off the Door Open

icon.

SpeedCool

The SpeedCool feature assists during times of high refrigerator

use, full grocery loads or temporarily warm room temperatures.

• Press SPEEDCOOL to set the freezer and refrigerator to the

coldest temperature settings. Press SPEEDCOOL again to

return to the selected temperature set point.

NOTES:

The SpeedCool icon will be illuminated while the

refrigerator is in SpeedCool mode.

The SpeedCool feature will turn off automatically after

24 hours.

_e E

Internal Control External Control

Moisture Control

The moisture control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Moisture Control is on.

NOTE: The moisture control icon will light up to indicate the

feature is on.

To turn on/off the moisture control feature:

• Internal Control Panel - Press and hold MOISTURE

CONTROL for 3 seconds.

• External Control Panel - Press and hold LIGHT for 3 seconds.

Internal Control External Control

Water Filter Status Light and Reset

The filter reset control allows you to restart the water filter status

tracking feature each time you replace the water filter. See "Water

Filtration System."

• Press and hold WATER FILTER for 3 seconds, to reset the

water filter status to Good. The water filter icon will turn blue.

Internal Control External Control

Air Filter Status Light and Reset

The filter reset control allows you to restart the air filter status

tracking feature each time you replace the air filter. See "Install Air

Filter."

• Press and hold AIR FILTER for 3 seconds, to reset the air filter

status to Good. The air filter icon will turn blue.

Internal Control External Control

IM PORTANT:

• Allow 3 hours for the refrigerator to cool down and chill water.

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The dispensing system will not operate when the refrigerator

door is open.

Flush the Water System

Air in the water dispensing system can cause the water dispenser

to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system.

Flushing the water dispensing system, forces air from the water

line and filter and prepares the water filter for use. Additional

flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

1. Using a sturdy container, depress and hold the water

dispenser paddle for 5 seconds.

2. Release the dispenser paddle for 5 seconds. Repeat steps 1

and 2 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing

the dispenser pad (5 seconds on, 5 seconds off) until a total

of 4 gal. (15 L) has been dispensed.

Dispense Water

IM PORTANT:

• The dispensing system will not operate when the refrigerator

door is open.

• The display screen on the dispenser control panel will turn off

automatically and enter "sleep" mode when the control

buttons and dispenser levers have not been used for

2 minutes or more. While in "sleep" mode, the first press of a

control button will only reactivate the display screen, without

changing any settings. After reactivation, changes to any

settings can then be made. If no changes are made within

2 minutes, the display will re-enter "sleep" mode.

To dispense water:

1. Press a sturdy glass against the water dispenser paddle.

2. Remove the glass to stop dispensing.

Dispenser Light

When you use the dispenser, the light will automatically turn on.

If you want the light to be on continuously, you may turn on the

light. The light icon will illuminate when the light is on.

ON: Press LIGHT quickly to turn on the dispenser light.

OFF: Press LIGHT quickly to turn off the dispenser light.

NOTES:

• If you unintentionally press and hold the LIGHT button for

3 seconds or longer, you will turn on the Moisture control

feature. If this happens, press and hold LIGHT for 3 seconds

again to turn off the Moisture control feature.

• The dispenser lights are LEDs that cannot be changed. If it

appears that your dispenser lights are not working, see

"Troubleshooting" for more information.

Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the

refrigerator, to the ice maker, or to the dispenser light. It simply

deactivates the controls and dispenser levers. To turn off the ice

maker, see "Ice Maker and Storage Bin."

• Press and hold SPEEDCOOL for 3 seconds to lock the

dispenser.

• Press and hold SPEEDCOOL for 3 seconds again to unlock

the dispenser.

The lock icon will illuminate when the dispenser is locked.

IMPORTANT: For models with a water filter, after connecting the

refrigerator to a water source or replacing the water filter, fill and

discard three full containers of ice to prepare the water filter for

use.

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Ice Storage Bin

1. Wash the ice storage bin with mild soap and warm water.

2. Slide the ice storage bin under the ice maker, and push it

toward the back as far as it will go.

3. Lower the arm on the ice maker to the "on" position.

NOTE: It usually takes approximately 24 hours for the ice

maker to begin producing ice. You may notice the ice has an

"off-taste." If so, discard the first three batches of ice

produced. After that the "off-taste" should be gone.

Ice Production Rate

• The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period. Allow 3 days to completely fill the

ice container.

• To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Control(s)." Wait 24 hours

between adjustments.

Remember

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice storage bin and the dispenser

mechanism.

Do not store anything on top of or in the ice maker or ice

storage bin.

REFRIGERATOR FEATURES

NOTE: Your model may have some or all of these features.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

i÷%,

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Glass Shelves

To remove a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift the back or front of the shelf

past the stop. Pull the shelf out the rest of the way.

To replace a shelf:

1. Slide the back of the shelf into the track in the wall of the

cabinet.

2. Guide the front of the shelf into the shelf track. Be sure to

slide the shelf in all the way.

Fold Away Shelf (on some models)

To retract the fold away shelf:

• Retract the fold away section of the shelf by holding the front

of the shelf with one hand and lifting up on the center front of

the shelf. Then push back and down on the shelf until it slides

beneath the back section of the shelf.

To replace the fold away shelf:

• Replace the fold away section of the shelf by holding the front

of the shelf with one hand and pulling the center of the shelf

until the fold away section is returned to its full shelf position.

Pantry Drawer Control

The amount of air flowing through the pantry drawer affects the

temperature inside the drawer.

The airflow control is located on the left side of the pantry drawer.

To adjust the airflow:

• Colder - Slide the control forward, toward the front of the

pantry drawer, the airflow is open.

• Cold - Slide the control all the way toward the rear of the

pantry drawer. The airflow is closed, as shown.

Pantry Drawer

To remove and replace the pantry drawer:

1. Slide pantry drawer out to the stop.

2. Lift front of pantry drawer with one hand while supporting

bottom of drawer with other hand. Slide drawer out the rest of

the way.

3. Replace the drawer by sliding it back in fully past the drawer

stop.

Pantry Drawer Cover

To remove and replace the pantry drawer cover:

1. Remove the pantry drawer.

2. From underneath, push up on the glass cover and pull it out.

3. Replace the pantry drawer cover by lowering it into place.

4. Replace the pantry drawer.

Crisper Drawers

To remove and replace the crisper drawer:

1. Slide the crisper drawer straight out to the stop. Lift the front

and slide the drawer out the rest of the way.

2. Replace the drawer by sliding the drawer in fully past the

stop.

Crisper Cover

To remove and replace the glass crisper cover:

1. Pull the glass straight out.

2. Replace the glass by pushing it straight in.

Crisper Humidity Control (on some models)

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

DOOR FEATURES

NOTE: Your model may have some or all of these features.

To remove and replace the condiment bins:

1. Tilt the bin by grabbing it and pulling outward.

2. Remove the bin by grabbing it and lifting it upward off the

glides.

3. Replace the bin by sliding it back onto the glides and then

push it closed.

BiR

To remove and replace the fresh bin:

1. Open the bin by grabbing the top center lip of the bin and

tilting the bin outward.

Remove the bin by grabbing both sides of the bin and lifting

the bin upward off the glides.

Replace the bin by sliding it back into its tilted position on the

glides and then push it closed.

To remove and replace the half-height bin:

1. Tilt the bin by grabbing it and pulling outward.

2. Remove the bin by grabbing it and lifting it upward off the

glides.

3. Replace the bin by sliding it back onto the glides and then

push it closed.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT:

• Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

• For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately

to avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately

to avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

IM PC RTANT:

• Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size,

shape, and wattage.

• To ensure optimum refrigerator performance, replace light

bulbs as soon as they burn out.

Refrigerator Compartment Light

The lighting located at the top of the refrigerator compartment

never needs to be replaced. If the lights do not illuminate when

the door is opened call for assistance or service. In the U.S.A, call

1-800-253-1301. In Canada, call 1-800-807-6777.

Freezer Compartment Light (on some models)

Unplug the refrigerator or disconnect power.

Remove the light shield (on some models).

• Top of the freezer compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

3. Replace the burned-out bulb with an appliance bulb(s) no

greater than 25 watts.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The refrigerator will not

operate

Check electrical supply Plug the power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Make sure there is power to the outlet. Plug in a lamp to see

if the outlet is working.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Check controls Make sure the controls are turned on. See "Using the

Controls."

New installation Allow 24 hours following installation for the refrigerator to

cool completely.

NOTE: Adjusting the temperature controls to the coldest

setting will not cool either compartment quicker.

La page charge ...

Maytag MFF2055YEW00 User Instructions

Marque: Maytag

Modèle: MFF2055YEW00

Catégorie: Frigos

Taper: User Instructions

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MFF2055YEW00

Maytag MFF2055YEW00 User Instructions

Ce manuel convient également à

Maytag MFF2055YEW00 User Instructions

dans d''autres langues

Documents connexes

Autres documents